| /* Copyright (c) 2008-2011, Code Aurora Forum. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| */ |
| /* |
| * SPI driver for Qualcomm MSM platforms |
| * |
| */ |
| #include <linux/version.h> |
| #include <linux/kernel.h> |
| #include <linux/init.h> |
| #include <linux/spinlock.h> |
| #include <linux/list.h> |
| #include <linux/irq.h> |
| #include <linux/platform_device.h> |
| #include <linux/spi/spi.h> |
| #include <linux/interrupt.h> |
| #include <linux/err.h> |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/workqueue.h> |
| #include <linux/io.h> |
| #include <linux/debugfs.h> |
| #include <mach/msm_spi.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/sched.h> |
| #include <mach/dma.h> |
| #include <asm/atomic.h> |
| #include <linux/mutex.h> |
| #include <linux/gpio.h> |
| #include <linux/remote_spinlock.h> |
| #include <linux/pm_qos_params.h> |
| |
| #define SPI_DRV_NAME "spi_qsd" |
| #if defined(CONFIG_SPI_QSD) || defined(CONFIG_SPI_QSD_MODULE) |
| |
| #define QSD_REG(x) (x) |
| #define QUP_REG(x) |
| |
| #define SPI_FIFO_WORD_CNT 0x0048 |
| |
| #elif defined(CONFIG_SPI_QUP) || defined(CONFIG_SPI_QUP_MODULE) |
| |
| #define QSD_REG(x) |
| #define QUP_REG(x) (x) |
| |
| #define QUP_CONFIG 0x0000 /* N & NO_INPUT/NO_OUPUT bits */ |
| #define QUP_ERROR_FLAGS 0x0308 |
| #define QUP_ERROR_FLAGS_EN 0x030C |
| #define QUP_ERR_MASK 0x3 |
| #define SPI_OUTPUT_FIFO_WORD_CNT 0x010C |
| #define SPI_INPUT_FIFO_WORD_CNT 0x0214 |
| #define QUP_MX_WRITE_COUNT 0x0150 |
| #define QUP_MX_WRITE_CNT_CURRENT 0x0154 |
| |
| #define QUP_CONFIG_SPI_MODE 0x0100 |
| |
| #define GSBI_CTRL_REG 0x0 |
| #define GSBI_SPI_CONFIG 0x30 |
| #endif |
| |
| #define SPI_CONFIG QSD_REG(0x0000) QUP_REG(0x0300) |
| #define SPI_IO_CONTROL QSD_REG(0x0004) QUP_REG(0x0304) |
| #define SPI_IO_MODES QSD_REG(0x0008) QUP_REG(0x0008) |
| #define SPI_SW_RESET QSD_REG(0x000C) QUP_REG(0x000C) |
| #define SPI_TIME_OUT QSD_REG(0x0010) QUP_REG(0x0010) |
| #define SPI_TIME_OUT_CURRENT QSD_REG(0x0014) QUP_REG(0x0014) |
| #define SPI_MX_OUTPUT_COUNT QSD_REG(0x0018) QUP_REG(0x0100) |
| #define SPI_MX_OUTPUT_CNT_CURRENT QSD_REG(0x001C) QUP_REG(0x0104) |
| #define SPI_MX_INPUT_COUNT QSD_REG(0x0020) QUP_REG(0x0200) |
| #define SPI_MX_INPUT_CNT_CURRENT QSD_REG(0x0024) QUP_REG(0x0204) |
| #define SPI_MX_READ_COUNT QSD_REG(0x0028) QUP_REG(0x0208) |
| #define SPI_MX_READ_CNT_CURRENT QSD_REG(0x002C) QUP_REG(0x020C) |
| #define SPI_OPERATIONAL QSD_REG(0x0030) QUP_REG(0x0018) |
| #define SPI_ERROR_FLAGS QSD_REG(0x0034) QUP_REG(0x001C) |
| #define SPI_ERROR_FLAGS_EN QSD_REG(0x0038) QUP_REG(0x0020) |
| #define SPI_DEASSERT_WAIT QSD_REG(0x003C) QUP_REG(0x0310) |
| #define SPI_OUTPUT_DEBUG QSD_REG(0x0040) QUP_REG(0x0108) |
| #define SPI_INPUT_DEBUG QSD_REG(0x0044) QUP_REG(0x0210) |
| #define SPI_TEST_CTRL QSD_REG(0x004C) QUP_REG(0x0024) |
| #define SPI_OUTPUT_FIFO QSD_REG(0x0100) QUP_REG(0x0110) |
| #define SPI_INPUT_FIFO QSD_REG(0x0200) QUP_REG(0x0218) |
| #define SPI_STATE QSD_REG(SPI_OPERATIONAL) QUP_REG(0x0004) |
| |
| /* SPI_CONFIG fields */ |
| #define SPI_CFG_INPUT_FIRST 0x00000200 |
| #define SPI_NO_INPUT 0x00000080 |
| #define SPI_NO_OUTPUT 0x00000040 |
| #define SPI_CFG_LOOPBACK 0x00000100 |
| #define SPI_CFG_N 0x0000001F |
| |
| /* SPI_IO_CONTROL fields */ |
| #define SPI_IO_C_CLK_IDLE_HIGH 0x00000400 |
| #define SPI_IO_C_MX_CS_MODE 0x00000100 |
| #define SPI_IO_C_CS_N_POLARITY 0x000000F0 |
| #define SPI_IO_C_CS_N_POLARITY_0 0x00000010 |
| #define SPI_IO_C_CS_SELECT 0x0000000C |
| #define SPI_IO_C_TRISTATE_CS 0x00000002 |
| #define SPI_IO_C_NO_TRI_STATE 0x00000001 |
| |
| /* SPI_IO_MODES fields */ |
| #define SPI_IO_M_OUTPUT_BIT_SHIFT_EN QSD_REG(0x00004000) QUP_REG(0x00010000) |
| #define SPI_IO_M_PACK_EN QSD_REG(0x00002000) QUP_REG(0x00008000) |
| #define SPI_IO_M_UNPACK_EN QSD_REG(0x00001000) QUP_REG(0x00004000) |
| #define SPI_IO_M_INPUT_MODE QSD_REG(0x00000C00) QUP_REG(0x00003000) |
| #define SPI_IO_M_OUTPUT_MODE QSD_REG(0x00000300) QUP_REG(0x00000C00) |
| #define SPI_IO_M_INPUT_FIFO_SIZE QSD_REG(0x000000C0) QUP_REG(0x00000380) |
| #define SPI_IO_M_INPUT_BLOCK_SIZE QSD_REG(0x00000030) QUP_REG(0x00000060) |
| #define SPI_IO_M_OUTPUT_FIFO_SIZE QSD_REG(0x0000000C) QUP_REG(0x0000001C) |
| #define SPI_IO_M_OUTPUT_BLOCK_SIZE QSD_REG(0x00000003) QUP_REG(0x00000003) |
| |
| #define INPUT_BLOCK_SZ_SHIFT QSD_REG(4) QUP_REG(5) |
| #define INPUT_FIFO_SZ_SHIFT QSD_REG(6) QUP_REG(7) |
| #define OUTPUT_BLOCK_SZ_SHIFT QSD_REG(0) QUP_REG(0) |
| #define OUTPUT_FIFO_SZ_SHIFT QSD_REG(2) QUP_REG(2) |
| #define OUTPUT_MODE_SHIFT QSD_REG(8) QUP_REG(10) |
| #define INPUT_MODE_SHIFT QSD_REG(10) QUP_REG(12) |
| |
| /* SPI_OPERATIONAL fields */ |
| #define SPI_OP_MAX_INPUT_DONE_FLAG 0x00000800 |
| #define SPI_OP_MAX_OUTPUT_DONE_FLAG 0x00000400 |
| #define SPI_OP_INPUT_SERVICE_FLAG 0x00000200 |
| #define SPI_OP_OUTPUT_SERVICE_FLAG 0x00000100 |
| #define SPI_OP_INPUT_FIFO_FULL 0x00000080 |
| #define SPI_OP_OUTPUT_FIFO_FULL 0x00000040 |
| #define SPI_OP_IP_FIFO_NOT_EMPTY 0x00000020 |
| #define SPI_OP_OP_FIFO_NOT_EMPTY 0x00000010 |
| #define SPI_OP_STATE_VALID 0x00000004 |
| #define SPI_OP_STATE 0x00000003 |
| |
| #define SPI_OP_STATE_CLEAR_BITS 0x2 |
| enum msm_spi_state { |
| SPI_OP_STATE_RESET = 0x00000000, |
| SPI_OP_STATE_RUN = 0x00000001, |
| SPI_OP_STATE_PAUSE = 0x00000003, |
| }; |
| |
| /* SPI_ERROR_FLAGS fields */ |
| #define SPI_ERR_OUTPUT_OVER_RUN_ERR 0x00000020 |
| #define SPI_ERR_INPUT_UNDER_RUN_ERR 0x00000010 |
| #define SPI_ERR_OUTPUT_UNDER_RUN_ERR 0x00000008 |
| #define SPI_ERR_INPUT_OVER_RUN_ERR 0x00000004 |
| #define SPI_ERR_CLK_OVER_RUN_ERR 0x00000002 |
| #define SPI_ERR_CLK_UNDER_RUN_ERR 0x00000001 |
| |
| /* We don't allow transactions larger than 4K-64 or 64K-64 due to |
| mx_input/output_cnt register size */ |
| #define SPI_MAX_TRANSFERS QSD_REG(0xFC0) QUP_REG(0xFC0) |
| #define SPI_MAX_LEN (SPI_MAX_TRANSFERS * dd->bytes_per_word) |
| |
| #define SPI_NUM_CHIPSELECTS 4 |
| #define SPI_SUPPORTED_MODES (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP) |
| |
| #define SPI_DELAY_THRESHOLD 1 |
| /* Default timeout is 10 milliseconds */ |
| #define SPI_DEFAULT_TIMEOUT 10 |
| /* 250 microseconds */ |
| #define SPI_TRYLOCK_DELAY 250 |
| |
| /* Data Mover burst size */ |
| #define DM_BURST_SIZE 16 |
| /* Data Mover commands should be aligned to 64 bit(8 bytes) */ |
| #define DM_BYTE_ALIGN 8 |
| |
| static char const * const spi_rsrcs[] = { |
| "spi_clk", |
| "spi_miso", |
| "spi_mosi" |
| }; |
| |
| static char const * const spi_cs_rsrcs[] = { |
| "spi_cs", |
| "spi_cs1", |
| "spi_cs2", |
| "spi_cs3", |
| }; |
| |
| enum msm_spi_mode { |
| SPI_FIFO_MODE = 0x0, /* 00 */ |
| SPI_BLOCK_MODE = 0x1, /* 01 */ |
| SPI_DMOV_MODE = 0x2, /* 10 */ |
| SPI_MODE_NONE = 0xFF, /* invalid value */ |
| }; |
| |
| /* Structure for SPI CS GPIOs */ |
| struct spi_cs_gpio { |
| int gpio_num; |
| bool valid; |
| }; |
| |
| /* Structures for Data Mover */ |
| struct spi_dmov_cmd { |
| dmov_box box; /* data aligned to max(dm_burst_size, block_size) |
| (<= fifo_size) */ |
| dmov_s single_pad; /* data unaligned to max(dm_burst_size, block_size) |
| padded to fit */ |
| dma_addr_t cmd_ptr; |
| }; |
| |
| MODULE_LICENSE("GPL v2"); |
| MODULE_VERSION("0.3"); |
| MODULE_ALIAS("platform:"SPI_DRV_NAME); |
| |
| static struct pm_qos_request_list qos_req_list; |
| |
| #ifdef CONFIG_DEBUG_FS |
| /* Used to create debugfs entries */ |
| static const struct { |
| const char *name; |
| mode_t mode; |
| int offset; |
| } debugfs_spi_regs[] = { |
| {"config", S_IRUGO | S_IWUSR, SPI_CONFIG}, |
| {"io_control", S_IRUGO | S_IWUSR, SPI_IO_CONTROL}, |
| {"io_modes", S_IRUGO | S_IWUSR, SPI_IO_MODES}, |
| {"sw_reset", S_IWUSR, SPI_SW_RESET}, |
| {"time_out", S_IRUGO | S_IWUSR, SPI_TIME_OUT}, |
| {"time_out_current", S_IRUGO, SPI_TIME_OUT_CURRENT}, |
| {"mx_output_count", S_IRUGO | S_IWUSR, SPI_MX_OUTPUT_COUNT}, |
| {"mx_output_cnt_current", S_IRUGO, SPI_MX_OUTPUT_CNT_CURRENT}, |
| {"mx_input_count", S_IRUGO | S_IWUSR, SPI_MX_INPUT_COUNT}, |
| {"mx_input_cnt_current", S_IRUGO, SPI_MX_INPUT_CNT_CURRENT}, |
| {"mx_read_count", S_IRUGO | S_IWUSR, SPI_MX_READ_COUNT}, |
| {"mx_read_cnt_current", S_IRUGO, SPI_MX_READ_CNT_CURRENT}, |
| {"operational", S_IRUGO | S_IWUSR, SPI_OPERATIONAL}, |
| {"error_flags", S_IRUGO | S_IWUSR, SPI_ERROR_FLAGS}, |
| {"error_flags_en", S_IRUGO | S_IWUSR, SPI_ERROR_FLAGS_EN}, |
| {"deassert_wait", S_IRUGO | S_IWUSR, SPI_DEASSERT_WAIT}, |
| {"output_debug", S_IRUGO, SPI_OUTPUT_DEBUG}, |
| {"input_debug", S_IRUGO, SPI_INPUT_DEBUG}, |
| {"test_ctrl", S_IRUGO | S_IWUSR, SPI_TEST_CTRL}, |
| {"output_fifo", S_IWUSR, SPI_OUTPUT_FIFO}, |
| {"input_fifo" , S_IRUSR, SPI_INPUT_FIFO}, |
| {"spi_state", S_IRUGO | S_IWUSR, SPI_STATE}, |
| #if defined(CONFIG_SPI_QSD) || defined(CONFIG_SPI_QSD_MODULE) |
| {"fifo_word_cnt", S_IRUGO, SPI_FIFO_WORD_CNT}, |
| #elif defined(CONFIG_SPI_QUP) || defined(CONFIG_SPI_QUP_MODULE) |
| {"qup_config", S_IRUGO | S_IWUSR, QUP_CONFIG}, |
| {"qup_error_flags", S_IRUGO | S_IWUSR, QUP_ERROR_FLAGS}, |
| {"qup_error_flags_en", S_IRUGO | S_IWUSR, QUP_ERROR_FLAGS_EN}, |
| {"mx_write_cnt", S_IRUGO | S_IWUSR, QUP_MX_WRITE_COUNT}, |
| {"mx_write_cnt_current", S_IRUGO, QUP_MX_WRITE_CNT_CURRENT}, |
| {"output_fifo_word_cnt", S_IRUGO, SPI_OUTPUT_FIFO_WORD_CNT}, |
| {"input_fifo_word_cnt", S_IRUGO, SPI_INPUT_FIFO_WORD_CNT}, |
| #endif |
| }; |
| #endif |
| |
| struct msm_spi { |
| u8 *read_buf; |
| const u8 *write_buf; |
| void __iomem *base; |
| void __iomem *gsbi_base; |
| struct device *dev; |
| spinlock_t queue_lock; |
| struct mutex core_lock; |
| struct list_head queue; |
| struct workqueue_struct *workqueue; |
| struct work_struct work_data; |
| struct spi_message *cur_msg; |
| struct spi_transfer *cur_transfer; |
| struct completion transfer_complete; |
| struct clk *clk; |
| struct clk *pclk; |
| unsigned long mem_phys_addr; |
| size_t mem_size; |
| unsigned long gsbi_mem_phys_addr; |
| size_t gsbi_mem_size; |
| int input_fifo_size; |
| int output_fifo_size; |
| u32 rx_bytes_remaining; |
| u32 tx_bytes_remaining; |
| u32 clock_speed; |
| int irq_in; |
| int read_xfr_cnt; |
| int write_xfr_cnt; |
| int write_len; |
| int read_len; |
| #if defined(CONFIG_SPI_QSD) || defined(CONFIG_SPI_QSD_MODULE) |
| int irq_out; |
| int irq_err; |
| #endif |
| int bytes_per_word; |
| bool suspended; |
| bool transfer_pending; |
| wait_queue_head_t continue_suspend; |
| /* DMA data */ |
| enum msm_spi_mode mode; |
| bool use_dma; |
| int tx_dma_chan; |
| int tx_dma_crci; |
| int rx_dma_chan; |
| int rx_dma_crci; |
| /* Data Mover Commands */ |
| struct spi_dmov_cmd *tx_dmov_cmd; |
| struct spi_dmov_cmd *rx_dmov_cmd; |
| /* Physical address of the tx dmov box command */ |
| dma_addr_t tx_dmov_cmd_dma; |
| dma_addr_t rx_dmov_cmd_dma; |
| struct msm_dmov_cmd tx_hdr; |
| struct msm_dmov_cmd rx_hdr; |
| int input_block_size; |
| int output_block_size; |
| int burst_size; |
| atomic_t rx_irq_called; |
| /* Used to pad messages unaligned to block size */ |
| u8 *tx_padding; |
| dma_addr_t tx_padding_dma; |
| u8 *rx_padding; |
| dma_addr_t rx_padding_dma; |
| u32 unaligned_len; |
| /* DMA statistics */ |
| int stat_dmov_tx_err; |
| int stat_dmov_rx_err; |
| int stat_rx; |
| int stat_dmov_rx; |
| int stat_tx; |
| int stat_dmov_tx; |
| #ifdef CONFIG_DEBUG_FS |
| struct dentry *dent_spi; |
| struct dentry *debugfs_spi_regs[ARRAY_SIZE(debugfs_spi_regs)]; |
| #endif |
| struct msm_spi_platform_data *pdata; /* Platform data */ |
| /* Remote Spinlock Data */ |
| bool use_rlock; |
| remote_mutex_t r_lock; |
| uint32_t pm_lat; |
| /* When set indicates multiple transfers in a single message */ |
| bool multi_xfr; |
| bool done; |
| u32 cur_msg_len; |
| /* Used in FIFO mode to keep track of the transfer being processed */ |
| struct spi_transfer *cur_tx_transfer; |
| struct spi_transfer *cur_rx_transfer; |
| /* Temporary buffer used for WR-WR or WR-RD transfers */ |
| u8 *temp_buf; |
| /* GPIO pin numbers for SPI clk, miso and mosi */ |
| int spi_gpios[ARRAY_SIZE(spi_rsrcs)]; |
| /* SPI CS GPIOs for each slave */ |
| struct spi_cs_gpio cs_gpios[ARRAY_SIZE(spi_cs_rsrcs)]; |
| }; |
| |
| /* Forward declaration */ |
| static irqreturn_t msm_spi_input_irq(int irq, void *dev_id); |
| static irqreturn_t msm_spi_output_irq(int irq, void *dev_id); |
| static irqreturn_t msm_spi_error_irq(int irq, void *dev_id); |
| static inline int msm_spi_set_state(struct msm_spi *dd, |
| enum msm_spi_state state); |
| static void msm_spi_write_word_to_fifo(struct msm_spi *dd); |
| static inline void msm_spi_write_rmn_to_fifo(struct msm_spi *dd); |
| |
| #if defined(CONFIG_SPI_QSD) || defined(CONFIG_SPI_QSD_MODULE) |
| /* Interrupt Handling */ |
| static inline int msm_spi_get_irq_data(struct msm_spi *dd, |
| struct platform_device *pdev) |
| { |
| dd->irq_in = platform_get_irq_byname(pdev, "spi_irq_in"); |
| dd->irq_out = platform_get_irq_byname(pdev, "spi_irq_out"); |
| dd->irq_err = platform_get_irq_byname(pdev, "spi_irq_err"); |
| if ((dd->irq_in < 0) || (dd->irq_out < 0) || (dd->irq_err < 0)) |
| return -1; |
| return 0; |
| } |
| |
| static inline int msm_spi_get_gsbi_resource(struct msm_spi *dd, |
| struct platform_device *pdev) |
| { |
| return 0; |
| } |
| |
| static inline int msm_spi_request_gsbi(struct msm_spi *dd) { return 0; } |
| static inline void msm_spi_release_gsbi(struct msm_spi *dd) {} |
| static inline void msm_spi_init_gsbi(struct msm_spi *dd) {} |
| |
| static inline void msm_spi_disable_irqs(struct msm_spi *dd) |
| { |
| disable_irq(dd->irq_in); |
| disable_irq(dd->irq_out); |
| disable_irq(dd->irq_err); |
| } |
| |
| static inline void msm_spi_enable_irqs(struct msm_spi *dd) |
| { |
| enable_irq(dd->irq_in); |
| enable_irq(dd->irq_out); |
| enable_irq(dd->irq_err); |
| } |
| |
| static inline int msm_spi_request_irq(struct msm_spi *dd, |
| const char *name, |
| struct spi_master *master) |
| { |
| int rc; |
| rc = request_irq(dd->irq_in, msm_spi_input_irq, IRQF_TRIGGER_RISING, |
| name, dd); |
| if (rc) |
| goto error_irq1; |
| rc = request_irq(dd->irq_out, msm_spi_output_irq, IRQF_TRIGGER_RISING, |
| name, dd); |
| if (rc) |
| goto error_irq2; |
| rc = request_irq(dd->irq_err, msm_spi_error_irq, IRQF_TRIGGER_RISING, |
| name, master); |
| if (rc) |
| goto error_irq3; |
| return 0; |
| |
| error_irq3: |
| free_irq(dd->irq_out, dd); |
| error_irq2: |
| free_irq(dd->irq_in, dd); |
| error_irq1: |
| return rc; |
| } |
| |
| static inline void msm_spi_free_irq(struct msm_spi *dd, |
| struct spi_master *master) |
| { |
| free_irq(dd->irq_err, master); |
| free_irq(dd->irq_out, dd); |
| free_irq(dd->irq_in, dd); |
| } |
| |
| static inline void msm_spi_get_clk_err(struct msm_spi *dd, u32 *spi_err) {} |
| static inline void msm_spi_ack_clk_err(struct msm_spi *dd) {} |
| static inline void msm_spi_set_qup_config(struct msm_spi *dd, int bpw) {} |
| |
| static inline int msm_spi_prepare_for_write(struct msm_spi *dd) { return 0; } |
| static inline void msm_spi_start_write(struct msm_spi *dd, u32 read_count) |
| { |
| msm_spi_write_word_to_fifo(dd); |
| } |
| static inline void msm_spi_set_write_count(struct msm_spi *dd, int val) {} |
| |
| static inline void msm_spi_complete(struct msm_spi *dd) |
| { |
| complete(&dd->transfer_complete); |
| } |
| |
| static inline void msm_spi_enable_error_flags(struct msm_spi *dd) |
| { |
| writel_relaxed(0x0000007B, dd->base + SPI_ERROR_FLAGS_EN); |
| } |
| |
| static inline void msm_spi_clear_error_flags(struct msm_spi *dd) |
| { |
| writel_relaxed(0x0000007F, dd->base + SPI_ERROR_FLAGS); |
| } |
| |
| #elif defined(CONFIG_SPI_QUP) || defined(CONFIG_SPI_QUP_MODULE) |
| |
| /* Interrupt Handling */ |
| /* In QUP the same interrupt line is used for intput, output and error*/ |
| static inline int msm_spi_get_irq_data(struct msm_spi *dd, |
| struct platform_device *pdev) |
| { |
| dd->irq_in = platform_get_irq_byname(pdev, "spi_irq_in"); |
| if (dd->irq_in < 0) |
| return -1; |
| return 0; |
| } |
| |
| static inline int msm_spi_get_gsbi_resource(struct msm_spi *dd, |
| struct platform_device *pdev) |
| { |
| struct resource *resource; |
| |
| resource = platform_get_resource_byname(pdev, |
| IORESOURCE_MEM, "gsbi_base"); |
| if (!resource) |
| return -ENXIO; |
| dd->gsbi_mem_phys_addr = resource->start; |
| dd->gsbi_mem_size = resource_size(resource); |
| |
| return 0; |
| } |
| |
| static inline void msm_spi_release_gsbi(struct msm_spi *dd) |
| { |
| iounmap(dd->gsbi_base); |
| release_mem_region(dd->gsbi_mem_phys_addr, dd->gsbi_mem_size); |
| } |
| |
| static inline int msm_spi_request_gsbi(struct msm_spi *dd) |
| { |
| if (!request_mem_region(dd->gsbi_mem_phys_addr, dd->gsbi_mem_size, |
| SPI_DRV_NAME)) { |
| return -ENXIO; |
| } |
| dd->gsbi_base = ioremap(dd->gsbi_mem_phys_addr, dd->gsbi_mem_size); |
| if (!dd->gsbi_base) { |
| release_mem_region(dd->gsbi_mem_phys_addr, dd->gsbi_mem_size); |
| return -ENXIO; |
| } |
| return 0; |
| } |
| |
| static inline void msm_spi_init_gsbi(struct msm_spi *dd) |
| { |
| /* Set GSBI to SPI mode, and CRCI_MUX_CTRL to SPI CRCI ports */ |
| writel_relaxed(GSBI_SPI_CONFIG, dd->gsbi_base + GSBI_CTRL_REG); |
| } |
| |
| /* Figure which irq occured and call the relevant functions */ |
| static irqreturn_t msm_spi_qup_irq(int irq, void *dev_id) |
| { |
| u32 op, ret = IRQ_NONE; |
| struct msm_spi *dd = dev_id; |
| |
| if (readl_relaxed(dd->base + SPI_ERROR_FLAGS) || |
| readl_relaxed(dd->base + QUP_ERROR_FLAGS)) { |
| struct spi_master *master = dev_get_drvdata(dd->dev); |
| ret |= msm_spi_error_irq(irq, master); |
| } |
| |
| op = readl_relaxed(dd->base + SPI_OPERATIONAL); |
| if (op & SPI_OP_INPUT_SERVICE_FLAG) { |
| writel_relaxed(SPI_OP_INPUT_SERVICE_FLAG, |
| dd->base + SPI_OPERATIONAL); |
| /* |
| * Ensure service flag was cleared before further |
| * processing of interrupt. |
| */ |
| mb(); |
| ret |= msm_spi_input_irq(irq, dev_id); |
| } |
| |
| if (op & SPI_OP_OUTPUT_SERVICE_FLAG) { |
| writel_relaxed(SPI_OP_OUTPUT_SERVICE_FLAG, |
| dd->base + SPI_OPERATIONAL); |
| /* |
| * Ensure service flag was cleared before further |
| * processing of interrupt. |
| */ |
| mb(); |
| ret |= msm_spi_output_irq(irq, dev_id); |
| } |
| |
| if (dd->done) { |
| complete(&dd->transfer_complete); |
| dd->done = 0; |
| } |
| return ret; |
| } |
| |
| static inline int msm_spi_request_irq(struct msm_spi *dd, |
| const char *name, |
| struct spi_master *master) |
| { |
| return request_irq(dd->irq_in, msm_spi_qup_irq, IRQF_TRIGGER_HIGH, |
| name, dd); |
| } |
| |
| static inline void msm_spi_free_irq(struct msm_spi *dd, |
| struct spi_master *master) |
| { |
| free_irq(dd->irq_in, dd); |
| } |
| |
| static inline void msm_spi_free_output_irq(struct msm_spi *dd) { } |
| static inline void msm_spi_free_error_irq(struct msm_spi *dd, |
| struct spi_master *master) { } |
| |
| static inline void msm_spi_disable_irqs(struct msm_spi *dd) |
| { |
| disable_irq(dd->irq_in); |
| } |
| |
| static inline void msm_spi_enable_irqs(struct msm_spi *dd) |
| { |
| enable_irq(dd->irq_in); |
| } |
| |
| static inline void msm_spi_get_clk_err(struct msm_spi *dd, u32 *spi_err) |
| { |
| *spi_err = readl_relaxed(dd->base + QUP_ERROR_FLAGS); |
| } |
| |
| static inline void msm_spi_ack_clk_err(struct msm_spi *dd) |
| { |
| writel_relaxed(QUP_ERR_MASK, dd->base + QUP_ERROR_FLAGS); |
| } |
| |
| static inline void msm_spi_add_configs(struct msm_spi *dd, u32 *config, int n); |
| |
| /* QUP has no_input, no_output, and N bits at QUP_CONFIG */ |
| static inline void msm_spi_set_qup_config(struct msm_spi *dd, int bpw) |
| { |
| u32 qup_config = readl_relaxed(dd->base + QUP_CONFIG); |
| |
| msm_spi_add_configs(dd, &qup_config, bpw-1); |
| writel_relaxed(qup_config | QUP_CONFIG_SPI_MODE, |
| dd->base + QUP_CONFIG); |
| } |
| |
| static inline int msm_spi_prepare_for_write(struct msm_spi *dd) |
| { |
| if (msm_spi_set_state(dd, SPI_OP_STATE_RUN)) |
| return -1; |
| if (msm_spi_set_state(dd, SPI_OP_STATE_PAUSE)) |
| return -1; |
| return 0; |
| } |
| |
| static inline void msm_spi_start_write(struct msm_spi *dd, u32 read_count) |
| { |
| if (read_count <= dd->input_fifo_size) |
| msm_spi_write_rmn_to_fifo(dd); |
| else |
| msm_spi_write_word_to_fifo(dd); |
| } |
| |
| static inline void msm_spi_set_write_count(struct msm_spi *dd, int val) |
| { |
| writel_relaxed(val, dd->base + QUP_MX_WRITE_COUNT); |
| } |
| |
| static inline void msm_spi_complete(struct msm_spi *dd) |
| { |
| dd->done = 1; |
| } |
| |
| static inline void msm_spi_enable_error_flags(struct msm_spi *dd) |
| { |
| writel_relaxed(0x00000078, dd->base + SPI_ERROR_FLAGS_EN); |
| } |
| |
| static inline void msm_spi_clear_error_flags(struct msm_spi *dd) |
| { |
| writel_relaxed(0x0000007C, dd->base + SPI_ERROR_FLAGS); |
| } |
| |
| #endif |
| |
| static inline int msm_spi_request_gpios(struct msm_spi *dd) |
| { |
| int i; |
| int result = 0; |
| |
| for (i = 0; i < ARRAY_SIZE(spi_rsrcs); ++i) { |
| if (dd->spi_gpios[i] >= 0) { |
| result = gpio_request(dd->spi_gpios[i], spi_rsrcs[i]); |
| if (result) { |
| dev_err(dd->dev, "%s: gpio_request for pin %d " |
| "failed with error %d\n", __func__, |
| dd->spi_gpios[i], result); |
| goto error; |
| } |
| } |
| } |
| return 0; |
| |
| error: |
| for (; --i >= 0;) { |
| if (dd->spi_gpios[i] >= 0) |
| gpio_free(dd->spi_gpios[i]); |
| } |
| return result; |
| } |
| |
| static inline void msm_spi_free_gpios(struct msm_spi *dd) |
| { |
| int i; |
| |
| for (i = 0; i < ARRAY_SIZE(spi_rsrcs); ++i) { |
| if (dd->spi_gpios[i] >= 0) |
| gpio_free(dd->spi_gpios[i]); |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(spi_cs_rsrcs); ++i) { |
| if (dd->cs_gpios[i].valid) { |
| gpio_free(dd->cs_gpios[i].gpio_num); |
| dd->cs_gpios[i].valid = 0; |
| } |
| } |
| } |
| |
| static void msm_spi_clock_set(struct msm_spi *dd, int speed) |
| { |
| int rc; |
| |
| rc = clk_set_rate(dd->clk, speed); |
| if (!rc) |
| dd->clock_speed = speed; |
| } |
| |
| static int msm_spi_calculate_size(int *fifo_size, |
| int *block_size, |
| int block, |
| int mult) |
| { |
| int words; |
| |
| switch (block) { |
| case 0: |
| words = 1; /* 4 bytes */ |
| break; |
| case 1: |
| words = 4; /* 16 bytes */ |
| break; |
| case 2: |
| words = 8; /* 32 bytes */ |
| break; |
| default: |
| return -1; |
| } |
| switch (mult) { |
| case 0: |
| *fifo_size = words * 2; |
| break; |
| case 1: |
| *fifo_size = words * 4; |
| break; |
| case 2: |
| *fifo_size = words * 8; |
| break; |
| case 3: |
| *fifo_size = words * 16; |
| break; |
| default: |
| return -1; |
| } |
| *block_size = words * sizeof(u32); /* in bytes */ |
| return 0; |
| } |
| |
| static void get_next_transfer(struct msm_spi *dd) |
| { |
| struct spi_transfer *t = dd->cur_transfer; |
| |
| if (t->transfer_list.next != &dd->cur_msg->transfers) { |
| dd->cur_transfer = list_entry(t->transfer_list.next, |
| struct spi_transfer, |
| transfer_list); |
| dd->write_buf = dd->cur_transfer->tx_buf; |
| dd->read_buf = dd->cur_transfer->rx_buf; |
| } |
| } |
| |
| static void __init msm_spi_calculate_fifo_size(struct msm_spi *dd) |
| { |
| u32 spi_iom; |
| int block; |
| int mult; |
| |
| spi_iom = readl_relaxed(dd->base + SPI_IO_MODES); |
| |
| block = (spi_iom & SPI_IO_M_INPUT_BLOCK_SIZE) >> INPUT_BLOCK_SZ_SHIFT; |
| mult = (spi_iom & SPI_IO_M_INPUT_FIFO_SIZE) >> INPUT_FIFO_SZ_SHIFT; |
| if (msm_spi_calculate_size(&dd->input_fifo_size, &dd->input_block_size, |
| block, mult)) { |
| goto fifo_size_err; |
| } |
| |
| block = (spi_iom & SPI_IO_M_OUTPUT_BLOCK_SIZE) >> OUTPUT_BLOCK_SZ_SHIFT; |
| mult = (spi_iom & SPI_IO_M_OUTPUT_FIFO_SIZE) >> OUTPUT_FIFO_SZ_SHIFT; |
| if (msm_spi_calculate_size(&dd->output_fifo_size, |
| &dd->output_block_size, block, mult)) { |
| goto fifo_size_err; |
| } |
| /* DM mode is not available for this block size */ |
| if (dd->input_block_size == 4 || dd->output_block_size == 4) |
| dd->use_dma = 0; |
| |
| /* DM mode is currently unsupported for different block sizes */ |
| if (dd->input_block_size != dd->output_block_size) |
| dd->use_dma = 0; |
| |
| if (dd->use_dma) |
| dd->burst_size = max(dd->input_block_size, DM_BURST_SIZE); |
| |
| return; |
| |
| fifo_size_err: |
| dd->use_dma = 0; |
| printk(KERN_WARNING "%s: invalid FIFO size, SPI_IO_MODES=0x%x\n", |
| __func__, spi_iom); |
| return; |
| } |
| |
| static void msm_spi_read_word_from_fifo(struct msm_spi *dd) |
| { |
| u32 data_in; |
| int i; |
| int shift; |
| |
| data_in = readl_relaxed(dd->base + SPI_INPUT_FIFO); |
| if (dd->read_buf) { |
| for (i = 0; (i < dd->bytes_per_word) && |
| dd->rx_bytes_remaining; i++) { |
| /* The data format depends on bytes_per_word: |
| 4 bytes: 0x12345678 |
| 3 bytes: 0x00123456 |
| 2 bytes: 0x00001234 |
| 1 byte : 0x00000012 |
| */ |
| shift = 8 * (dd->bytes_per_word - i - 1); |
| *dd->read_buf++ = (data_in & (0xFF << shift)) >> shift; |
| dd->rx_bytes_remaining--; |
| } |
| } else { |
| if (dd->rx_bytes_remaining >= dd->bytes_per_word) |
| dd->rx_bytes_remaining -= dd->bytes_per_word; |
| else |
| dd->rx_bytes_remaining = 0; |
| } |
| dd->read_xfr_cnt++; |
| if (dd->multi_xfr) { |
| if (!dd->rx_bytes_remaining) |
| dd->read_xfr_cnt = 0; |
| else if ((dd->read_xfr_cnt * dd->bytes_per_word) == |
| dd->read_len) { |
| struct spi_transfer *t = dd->cur_rx_transfer; |
| if (t->transfer_list.next != &dd->cur_msg->transfers) { |
| t = list_entry(t->transfer_list.next, |
| struct spi_transfer, |
| transfer_list); |
| dd->read_buf = t->rx_buf; |
| dd->read_len = t->len; |
| dd->read_xfr_cnt = 0; |
| dd->cur_rx_transfer = t; |
| } |
| } |
| } |
| } |
| |
| static inline bool msm_spi_is_valid_state(struct msm_spi *dd) |
| { |
| u32 spi_op = readl_relaxed(dd->base + SPI_STATE); |
| |
| return spi_op & SPI_OP_STATE_VALID; |
| } |
| |
| static inline int msm_spi_wait_valid(struct msm_spi *dd) |
| { |
| unsigned long delay = 0; |
| unsigned long timeout = 0; |
| |
| if (dd->clock_speed == 0) |
| return -EINVAL; |
| /* |
| * Based on the SPI clock speed, sufficient time |
| * should be given for the SPI state transition |
| * to occur |
| */ |
| delay = (10 * USEC_PER_SEC) / dd->clock_speed; |
| /* |
| * For small delay values, the default timeout would |
| * be one jiffy |
| */ |
| if (delay < SPI_DELAY_THRESHOLD) |
| delay = SPI_DELAY_THRESHOLD; |
| |
| /* Adding one to round off to the nearest jiffy */ |
| timeout = jiffies + msecs_to_jiffies(delay * SPI_DEFAULT_TIMEOUT) + 1; |
| while (!msm_spi_is_valid_state(dd)) { |
| if (time_after(jiffies, timeout)) { |
| if (!msm_spi_is_valid_state(dd)) { |
| if (dd->cur_msg) |
| dd->cur_msg->status = -EIO; |
| dev_err(dd->dev, "%s: SPI operational state" |
| "not valid\n", __func__); |
| return -ETIMEDOUT; |
| } else |
| return 0; |
| } |
| /* |
| * For smaller values of delay, context switch time |
| * would negate the usage of usleep |
| */ |
| if (delay > 20) |
| usleep(delay); |
| else if (delay) |
| udelay(delay); |
| } |
| return 0; |
| } |
| |
| static inline int msm_spi_set_state(struct msm_spi *dd, |
| enum msm_spi_state state) |
| { |
| enum msm_spi_state cur_state; |
| if (msm_spi_wait_valid(dd)) |
| return -1; |
| cur_state = readl_relaxed(dd->base + SPI_STATE); |
| /* Per spec: |
| For PAUSE_STATE to RESET_STATE, two writes of (10) are required */ |
| if (((cur_state & SPI_OP_STATE) == SPI_OP_STATE_PAUSE) && |
| (state == SPI_OP_STATE_RESET)) { |
| writel_relaxed(SPI_OP_STATE_CLEAR_BITS, dd->base + SPI_STATE); |
| writel_relaxed(SPI_OP_STATE_CLEAR_BITS, dd->base + SPI_STATE); |
| } else { |
| writel_relaxed((cur_state & ~SPI_OP_STATE) | state, |
| dd->base + SPI_STATE); |
| } |
| if (msm_spi_wait_valid(dd)) |
| return -1; |
| |
| return 0; |
| } |
| |
| static inline void msm_spi_add_configs(struct msm_spi *dd, u32 *config, int n) |
| { |
| *config &= ~(SPI_NO_INPUT|SPI_NO_OUTPUT); |
| |
| if (n != (*config & SPI_CFG_N)) |
| *config = (*config & ~SPI_CFG_N) | n; |
| |
| if ((dd->mode == SPI_DMOV_MODE) && (!dd->read_len)) { |
| if (dd->read_buf == NULL) |
| *config |= SPI_NO_INPUT; |
| if (dd->write_buf == NULL) |
| *config |= SPI_NO_OUTPUT; |
| } |
| } |
| |
| static void msm_spi_set_config(struct msm_spi *dd, int bpw) |
| { |
| u32 spi_config; |
| |
| spi_config = readl_relaxed(dd->base + SPI_CONFIG); |
| |
| if (dd->cur_msg->spi->mode & SPI_CPHA) |
| spi_config &= ~SPI_CFG_INPUT_FIRST; |
| else |
| spi_config |= SPI_CFG_INPUT_FIRST; |
| if (dd->cur_msg->spi->mode & SPI_LOOP) |
| spi_config |= SPI_CFG_LOOPBACK; |
| else |
| spi_config &= ~SPI_CFG_LOOPBACK; |
| msm_spi_add_configs(dd, &spi_config, bpw-1); |
| writel_relaxed(spi_config, dd->base + SPI_CONFIG); |
| msm_spi_set_qup_config(dd, bpw); |
| } |
| |
| static void msm_spi_setup_dm_transfer(struct msm_spi *dd) |
| { |
| dmov_box *box; |
| int bytes_to_send, num_rows, bytes_sent; |
| u32 num_transfers; |
| |
| atomic_set(&dd->rx_irq_called, 0); |
| if (dd->write_len && !dd->read_len) { |
| /* WR-WR transfer */ |
| bytes_sent = dd->cur_msg_len - dd->tx_bytes_remaining; |
| dd->write_buf = dd->temp_buf; |
| } else { |
| bytes_sent = dd->cur_transfer->len - dd->tx_bytes_remaining; |
| /* For WR-RD transfer, bytes_sent can be negative */ |
| if (bytes_sent < 0) |
| bytes_sent = 0; |
| } |
| |
| /* We'll send in chunks of SPI_MAX_LEN if larger */ |
| bytes_to_send = dd->tx_bytes_remaining / SPI_MAX_LEN ? |
| SPI_MAX_LEN : dd->tx_bytes_remaining; |
| num_transfers = DIV_ROUND_UP(bytes_to_send, dd->bytes_per_word); |
| dd->unaligned_len = bytes_to_send % dd->burst_size; |
| num_rows = bytes_to_send / dd->burst_size; |
| |
| dd->mode = SPI_DMOV_MODE; |
| |
| if (num_rows) { |
| /* src in 16 MSB, dst in 16 LSB */ |
| box = &dd->tx_dmov_cmd->box; |
| box->src_row_addr = dd->cur_transfer->tx_dma + bytes_sent; |
| box->src_dst_len = (dd->burst_size << 16) | dd->burst_size; |
| box->num_rows = (num_rows << 16) | num_rows; |
| box->row_offset = (dd->burst_size << 16) | 0; |
| |
| box = &dd->rx_dmov_cmd->box; |
| box->dst_row_addr = dd->cur_transfer->rx_dma + bytes_sent; |
| box->src_dst_len = (dd->burst_size << 16) | dd->burst_size; |
| box->num_rows = (num_rows << 16) | num_rows; |
| box->row_offset = (0 << 16) | dd->burst_size; |
| |
| dd->tx_dmov_cmd->cmd_ptr = CMD_PTR_LP | |
| DMOV_CMD_ADDR(dd->tx_dmov_cmd_dma + |
| offsetof(struct spi_dmov_cmd, box)); |
| dd->rx_dmov_cmd->cmd_ptr = CMD_PTR_LP | |
| DMOV_CMD_ADDR(dd->rx_dmov_cmd_dma + |
| offsetof(struct spi_dmov_cmd, box)); |
| } else { |
| dd->tx_dmov_cmd->cmd_ptr = CMD_PTR_LP | |
| DMOV_CMD_ADDR(dd->tx_dmov_cmd_dma + |
| offsetof(struct spi_dmov_cmd, single_pad)); |
| dd->rx_dmov_cmd->cmd_ptr = CMD_PTR_LP | |
| DMOV_CMD_ADDR(dd->rx_dmov_cmd_dma + |
| offsetof(struct spi_dmov_cmd, single_pad)); |
| } |
| |
| if (!dd->unaligned_len) { |
| dd->tx_dmov_cmd->box.cmd |= CMD_LC; |
| dd->rx_dmov_cmd->box.cmd |= CMD_LC; |
| } else { |
| dmov_s *tx_cmd = &(dd->tx_dmov_cmd->single_pad); |
| dmov_s *rx_cmd = &(dd->rx_dmov_cmd->single_pad); |
| u32 offset = dd->cur_transfer->len - dd->unaligned_len; |
| |
| if ((dd->multi_xfr) && (dd->read_len <= 0)) |
| offset = dd->cur_msg_len - dd->unaligned_len; |
| |
| dd->tx_dmov_cmd->box.cmd &= ~CMD_LC; |
| dd->rx_dmov_cmd->box.cmd &= ~CMD_LC; |
| |
| memset(dd->tx_padding, 0, dd->burst_size); |
| memset(dd->rx_padding, 0, dd->burst_size); |
| if (dd->write_buf) |
| memcpy(dd->tx_padding, dd->write_buf + offset, |
| dd->unaligned_len); |
| |
| tx_cmd->src = dd->tx_padding_dma; |
| rx_cmd->dst = dd->rx_padding_dma; |
| tx_cmd->len = rx_cmd->len = dd->burst_size; |
| } |
| /* This also takes care of the padding dummy buf |
| Since this is set to the correct length, the |
| dummy bytes won't be actually sent */ |
| if (dd->multi_xfr) { |
| u32 write_transfers = 0; |
| u32 read_transfers = 0; |
| |
| if (dd->write_len > 0) { |
| write_transfers = DIV_ROUND_UP(dd->write_len, |
| dd->bytes_per_word); |
| writel_relaxed(write_transfers, |
| dd->base + SPI_MX_OUTPUT_COUNT); |
| } |
| if (dd->read_len > 0) { |
| /* |
| * The read following a write transfer must take |
| * into account, that the bytes pertaining to |
| * the write transfer needs to be discarded, |
| * before the actual read begins. |
| */ |
| read_transfers = DIV_ROUND_UP(dd->read_len + |
| dd->write_len, |
| dd->bytes_per_word); |
| writel_relaxed(read_transfers, |
| dd->base + SPI_MX_INPUT_COUNT); |
| } |
| } else { |
| if (dd->write_buf) |
| writel_relaxed(num_transfers, |
| dd->base + SPI_MX_OUTPUT_COUNT); |
| if (dd->read_buf) |
| writel_relaxed(num_transfers, |
| dd->base + SPI_MX_INPUT_COUNT); |
| } |
| } |
| |
| static void msm_spi_enqueue_dm_commands(struct msm_spi *dd) |
| { |
| dma_coherent_pre_ops(); |
| if (dd->write_buf) |
| msm_dmov_enqueue_cmd(dd->tx_dma_chan, &dd->tx_hdr); |
| if (dd->read_buf) |
| msm_dmov_enqueue_cmd(dd->rx_dma_chan, &dd->rx_hdr); |
| } |
| |
| /* SPI core can send maximum of 4K transfers, because there is HW problem |
| with infinite mode. |
| Therefore, we are sending several chunks of 3K or less (depending on how |
| much is left). |
| Upon completion we send the next chunk, or complete the transfer if |
| everything is finished. |
| */ |
| static int msm_spi_dm_send_next(struct msm_spi *dd) |
| { |
| /* By now we should have sent all the bytes in FIFO mode, |
| * However to make things right, we'll check anyway. |
| */ |
| if (dd->mode != SPI_DMOV_MODE) |
| return 0; |
| |
| /* We need to send more chunks, if we sent max last time */ |
| if (dd->tx_bytes_remaining > SPI_MAX_LEN) { |
| dd->tx_bytes_remaining -= SPI_MAX_LEN; |
| if (msm_spi_set_state(dd, SPI_OP_STATE_RESET)) |
| return 0; |
| dd->read_len = dd->write_len = 0; |
| msm_spi_setup_dm_transfer(dd); |
| msm_spi_enqueue_dm_commands(dd); |
| if (msm_spi_set_state(dd, SPI_OP_STATE_RUN)) |
| return 0; |
| return 1; |
| } else if (dd->read_len && dd->write_len) { |
| dd->tx_bytes_remaining -= dd->cur_transfer->len; |
| if (list_is_last(&dd->cur_transfer->transfer_list, |
| &dd->cur_msg->transfers)) |
| return 0; |
| get_next_transfer(dd); |
| if (msm_spi_set_state(dd, SPI_OP_STATE_PAUSE)) |
| return 0; |
| dd->tx_bytes_remaining = dd->read_len + dd->write_len; |
| dd->read_buf = dd->temp_buf; |
| dd->read_len = dd->write_len = -1; |
| msm_spi_setup_dm_transfer(dd); |
| msm_spi_enqueue_dm_commands(dd); |
| if (msm_spi_set_state(dd, SPI_OP_STATE_RUN)) |
| return 0; |
| return 1; |
| } |
| return 0; |
| } |
| |
| static inline void msm_spi_ack_transfer(struct msm_spi *dd) |
| { |
| writel_relaxed(SPI_OP_MAX_INPUT_DONE_FLAG | |
| SPI_OP_MAX_OUTPUT_DONE_FLAG, |
| dd->base + SPI_OPERATIONAL); |
| /* Ensure done flag was cleared before proceeding further */ |
| mb(); |
| } |
| |
| static irqreturn_t msm_spi_input_irq(int irq, void *dev_id) |
| { |
| struct msm_spi *dd = dev_id; |
| |
| dd->stat_rx++; |
| |
| if (dd->mode == SPI_MODE_NONE) |
| return IRQ_HANDLED; |
| |
| if (dd->mode == SPI_DMOV_MODE) { |
| u32 op = readl_relaxed(dd->base + SPI_OPERATIONAL); |
| if ((!dd->read_buf || op & SPI_OP_MAX_INPUT_DONE_FLAG) && |
| (!dd->write_buf || op & SPI_OP_MAX_OUTPUT_DONE_FLAG)) { |
| msm_spi_ack_transfer(dd); |
| if (dd->unaligned_len == 0) { |
| if (atomic_inc_return(&dd->rx_irq_called) == 1) |
| return IRQ_HANDLED; |
| } |
| msm_spi_complete(dd); |
| return IRQ_HANDLED; |
| } |
| return IRQ_NONE; |
| } |
| |
| if (dd->mode == SPI_FIFO_MODE) { |
| while ((readl_relaxed(dd->base + SPI_OPERATIONAL) & |
| SPI_OP_IP_FIFO_NOT_EMPTY) && |
| (dd->rx_bytes_remaining > 0)) { |
| msm_spi_read_word_from_fifo(dd); |
| } |
| if (dd->rx_bytes_remaining == 0) |
| msm_spi_complete(dd); |
| } |
| |
| return IRQ_HANDLED; |
| } |
| |
| static void msm_spi_write_word_to_fifo(struct msm_spi *dd) |
| { |
| u32 word; |
| u8 byte; |
| int i; |
| |
| word = 0; |
| if (dd->write_buf) { |
| for (i = 0; (i < dd->bytes_per_word) && |
| dd->tx_bytes_remaining; i++) { |
| dd->tx_bytes_remaining--; |
| byte = *dd->write_buf++; |
| word |= (byte << (BITS_PER_BYTE * (3 - i))); |
| } |
| } else |
| if (dd->tx_bytes_remaining > dd->bytes_per_word) |
| dd->tx_bytes_remaining -= dd->bytes_per_word; |
| else |
| dd->tx_bytes_remaining = 0; |
| dd->write_xfr_cnt++; |
| if (dd->multi_xfr) { |
| if (!dd->tx_bytes_remaining) |
| dd->write_xfr_cnt = 0; |
| else if ((dd->write_xfr_cnt * dd->bytes_per_word) == |
| dd->write_len) { |
| struct spi_transfer *t = dd->cur_tx_transfer; |
| if (t->transfer_list.next != &dd->cur_msg->transfers) { |
| t = list_entry(t->transfer_list.next, |
| struct spi_transfer, |
| transfer_list); |
| dd->write_buf = t->tx_buf; |
| dd->write_len = t->len; |
| dd->write_xfr_cnt = 0; |
| dd->cur_tx_transfer = t; |
| } |
| } |
| } |
| writel_relaxed(word, dd->base + SPI_OUTPUT_FIFO); |
| } |
| |
| static inline void msm_spi_write_rmn_to_fifo(struct msm_spi *dd) |
| { |
| int count = 0; |
| |
| while ((dd->tx_bytes_remaining > 0) && (count < dd->input_fifo_size) && |
| !(readl_relaxed(dd->base + SPI_OPERATIONAL) & |
| SPI_OP_OUTPUT_FIFO_FULL)) { |
| msm_spi_write_word_to_fifo(dd); |
| count++; |
| } |
| } |
| |
| static irqreturn_t msm_spi_output_irq(int irq, void *dev_id) |
| { |
| struct msm_spi *dd = dev_id; |
| |
| dd->stat_tx++; |
| |
| if (dd->mode == SPI_MODE_NONE) |
| return IRQ_HANDLED; |
| |
| if (dd->mode == SPI_DMOV_MODE) { |
| /* TX_ONLY transaction is handled here |
| This is the only place we send complete at tx and not rx */ |
| if (dd->read_buf == NULL && |
| readl_relaxed(dd->base + SPI_OPERATIONAL) & |
| SPI_OP_MAX_OUTPUT_DONE_FLAG) { |
| msm_spi_ack_transfer(dd); |
| msm_spi_complete(dd); |
| return IRQ_HANDLED; |
| } |
| return IRQ_NONE; |
| } |
| |
| /* Output FIFO is empty. Transmit any outstanding write data. */ |
| if (dd->mode == SPI_FIFO_MODE) |
| msm_spi_write_rmn_to_fifo(dd); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t msm_spi_error_irq(int irq, void *dev_id) |
| { |
| struct spi_master *master = dev_id; |
| struct msm_spi *dd = spi_master_get_devdata(master); |
| u32 spi_err; |
| |
| spi_err = readl_relaxed(dd->base + SPI_ERROR_FLAGS); |
| if (spi_err & SPI_ERR_OUTPUT_OVER_RUN_ERR) |
| dev_warn(master->dev.parent, "SPI output overrun error\n"); |
| if (spi_err & SPI_ERR_INPUT_UNDER_RUN_ERR) |
| dev_warn(master->dev.parent, "SPI input underrun error\n"); |
| if (spi_err & SPI_ERR_OUTPUT_UNDER_RUN_ERR) |
| dev_warn(master->dev.parent, "SPI output underrun error\n"); |
| msm_spi_get_clk_err(dd, &spi_err); |
| if (spi_err & SPI_ERR_CLK_OVER_RUN_ERR) |
| dev_warn(master->dev.parent, "SPI clock overrun error\n"); |
| if (spi_err & SPI_ERR_CLK_UNDER_RUN_ERR) |
| dev_warn(master->dev.parent, "SPI clock underrun error\n"); |
| msm_spi_clear_error_flags(dd); |
| msm_spi_ack_clk_err(dd); |
| /* Ensure clearing of QUP_ERROR_FLAGS was completed */ |
| mb(); |
| return IRQ_HANDLED; |
| } |
| |
| static int msm_spi_map_dma_buffers(struct msm_spi *dd) |
| { |
| struct device *dev; |
| struct spi_transfer *first_xfr; |
| struct spi_transfer *nxt_xfr = NULL; |
| void *tx_buf, *rx_buf; |
| unsigned tx_len, rx_len; |
| int ret = -EINVAL; |
| |
| dev = &dd->cur_msg->spi->dev; |
| first_xfr = dd->cur_transfer; |
| tx_buf = (void *)first_xfr->tx_buf; |
| rx_buf = first_xfr->rx_buf; |
| tx_len = rx_len = first_xfr->len; |
| |
| /* |
| * For WR-WR and WR-RD transfers, we allocate our own temporary |
| * buffer and copy the data to/from the client buffers. |
| */ |
| if (dd->multi_xfr) { |
| dd->temp_buf = kzalloc(dd->cur_msg_len, |
| GFP_KERNEL | __GFP_DMA); |
| if (!dd->temp_buf) |
| return -ENOMEM; |
| nxt_xfr = list_entry(first_xfr->transfer_list.next, |
| struct spi_transfer, transfer_list); |
| |
| if (dd->write_len && !dd->read_len) { |
| if (!first_xfr->tx_buf || !nxt_xfr->tx_buf) |
| goto error; |
| |
| memcpy(dd->temp_buf, first_xfr->tx_buf, first_xfr->len); |
| memcpy(dd->temp_buf + first_xfr->len, nxt_xfr->tx_buf, |
| nxt_xfr->len); |
| tx_buf = dd->temp_buf; |
| tx_len = dd->cur_msg_len; |
| } else { |
| if (!first_xfr->tx_buf || !nxt_xfr->rx_buf) |
| goto error; |
| |
| rx_buf = dd->temp_buf; |
| rx_len = dd->cur_msg_len; |
| } |
| } |
| if (tx_buf != NULL) { |
| first_xfr->tx_dma = dma_map_single(dev, tx_buf, |
| tx_len, DMA_TO_DEVICE); |
| if (dma_mapping_error(NULL, first_xfr->tx_dma)) { |
| dev_err(dev, "dma %cX %d bytes error\n", |
| 'T', tx_len); |
| ret = -ENOMEM; |
| goto error; |
| } |
| } |
| if (rx_buf != NULL) { |
| dma_addr_t dma_handle; |
| dma_handle = dma_map_single(dev, rx_buf, |
| rx_len, DMA_FROM_DEVICE); |
| if (dma_mapping_error(NULL, dma_handle)) { |
| dev_err(dev, "dma %cX %d bytes error\n", |
| 'R', rx_len); |
| if (tx_buf != NULL) |
| dma_unmap_single(NULL, first_xfr->tx_dma, |
| tx_len, DMA_TO_DEVICE); |
| ret = -ENOMEM; |
| goto error; |
| } |
| if (dd->multi_xfr) |
| nxt_xfr->rx_dma = dma_handle; |
| else |
| first_xfr->rx_dma = dma_handle; |
| } |
| return 0; |
| |
| error: |
| kfree(dd->temp_buf); |
| dd->temp_buf = NULL; |
| return ret; |
| } |
| |
| static void msm_spi_unmap_dma_buffers(struct msm_spi *dd) |
| { |
| struct device *dev; |
| u32 offset; |
| |
| dev = &dd->cur_msg->spi->dev; |
| if (dd->cur_msg->is_dma_mapped) |
| goto unmap_end; |
| |
| if (dd->multi_xfr) { |
| if (dd->write_len && !dd->read_len) { |
| dma_unmap_single(dev, |
| dd->cur_transfer->tx_dma, |
| dd->cur_msg_len, |
| DMA_TO_DEVICE); |
| } else { |
| struct spi_transfer *prev_xfr; |
| prev_xfr = list_entry( |
| dd->cur_transfer->transfer_list.prev, |
| struct spi_transfer, |
| transfer_list); |
| if (dd->cur_transfer->rx_buf) { |
| dma_unmap_single(dev, |
| dd->cur_transfer->rx_dma, |
| dd->cur_msg_len, |
| DMA_FROM_DEVICE); |
| } |
| if (prev_xfr->tx_buf) { |
| dma_unmap_single(dev, |
| prev_xfr->tx_dma, |
| prev_xfr->len, |
| DMA_TO_DEVICE); |
| } |
| if (dd->unaligned_len && dd->read_buf) { |
| offset = dd->cur_msg_len - dd->unaligned_len; |
| dma_coherent_post_ops(); |
| memcpy(dd->read_buf + offset, dd->rx_padding, |
| dd->unaligned_len); |
| memcpy(dd->cur_transfer->rx_buf, |
| dd->read_buf + prev_xfr->len, |
| dd->cur_transfer->len); |
| } |
| } |
| kfree(dd->temp_buf); |
| dd->temp_buf = NULL; |
| return; |
| } else { |
| if (dd->cur_transfer->rx_buf) |
| dma_unmap_single(dev, dd->cur_transfer->rx_dma, |
| dd->cur_transfer->len, |
| DMA_FROM_DEVICE); |
| if (dd->cur_transfer->tx_buf) |
| dma_unmap_single(dev, dd->cur_transfer->tx_dma, |
| dd->cur_transfer->len, |
| DMA_TO_DEVICE); |
| } |
| |
| unmap_end: |
| /* If we padded the transfer, we copy it from the padding buf */ |
| if (dd->unaligned_len && dd->read_buf) { |
| offset = dd->cur_transfer->len - dd->unaligned_len; |
| dma_coherent_post_ops(); |
| memcpy(dd->read_buf + offset, dd->rx_padding, |
| dd->unaligned_len); |
| } |
| } |
| |
| /** |
| * msm_use_dm - decides whether to use data mover for this |
| * transfer |
| * @dd: device |
| * @tr: transfer |
| * |
| * Start using DM if: |
| * 1. Transfer is longer than 3*block size. |
| * 2. Buffers should be aligned to cache line. |
| * 3. For WR-RD or WR-WR transfers, if condition (1) and (2) above are met. |
| */ |
| static inline int msm_use_dm(struct msm_spi *dd, struct spi_transfer *tr, |
| u8 bpw) |
| { |
| u32 cache_line = dma_get_cache_alignment(); |
| |
| if (!dd->use_dma) |
| return 0; |
| |
| if (dd->cur_msg_len < 3*dd->input_block_size) |
| return 0; |
| |
| if (dd->multi_xfr && !dd->read_len && !dd->write_len) |
| return 0; |
| |
| if (tr->tx_buf) { |
| if (!IS_ALIGNED((size_t)tr->tx_buf, cache_line)) |
| return 0; |
| } |
| if (tr->rx_buf) { |
| if (!IS_ALIGNED((size_t)tr->rx_buf, cache_line)) |
| return 0; |
| } |
| |
| if (tr->cs_change && |
| ((bpw != 8) || (bpw != 16) || (bpw != 32))) |
| return 0; |
| return 1; |
| } |
| |
| static void msm_spi_process_transfer(struct msm_spi *dd) |
| { |
| u8 bpw; |
| u32 spi_ioc; |
| u32 spi_iom; |
| u32 spi_ioc_orig; |
| u32 max_speed; |
| u32 chip_select; |
| u32 read_count; |
| u32 timeout; |
| u32 int_loopback = 0; |
| |
| dd->tx_bytes_remaining = dd->cur_msg_len; |
| dd->rx_bytes_remaining = dd->cur_msg_len; |
| dd->read_buf = dd->cur_transfer->rx_buf; |
| dd->write_buf = dd->cur_transfer->tx_buf; |
| init_completion(&dd->transfer_complete); |
| if (dd->cur_transfer->bits_per_word) |
| bpw = dd->cur_transfer->bits_per_word; |
| else |
| if (dd->cur_msg->spi->bits_per_word) |
| bpw = dd->cur_msg->spi->bits_per_word; |
| else |
| bpw = 8; |
| dd->bytes_per_word = (bpw + 7) / 8; |
| |
| if (dd->cur_transfer->speed_hz) |
| max_speed = dd->cur_transfer->speed_hz; |
| else |
| max_speed = dd->cur_msg->spi->max_speed_hz; |
| if (!dd->clock_speed || max_speed != dd->clock_speed) |
| msm_spi_clock_set(dd, max_speed); |
| |
| read_count = DIV_ROUND_UP(dd->cur_msg_len, dd->bytes_per_word); |
| if (dd->cur_msg->spi->mode & SPI_LOOP) |
| int_loopback = 1; |
| if (int_loopback && dd->multi_xfr && |
| (read_count > dd->input_fifo_size)) { |
| if (dd->read_len && dd->write_len) |
| printk(KERN_WARNING |
| "%s:Internal Loopback does not support > fifo size\ |
| for write-then-read transactions\n", |
| __func__); |
| else if (dd->write_len && !dd->read_len) |
| printk(KERN_WARNING |
| "%s:Internal Loopback does not support > fifo size\ |
| for write-then-write transactions\n", |
| __func__); |
| return; |
| } |
| if (!msm_use_dm(dd, dd->cur_transfer, bpw)) { |
| dd->mode = SPI_FIFO_MODE; |
| if (dd->multi_xfr) { |
| dd->read_len = dd->cur_transfer->len; |
| dd->write_len = dd->cur_transfer->len; |
| } |
| /* read_count cannot exceed fifo_size, and only one READ COUNT |
| interrupt is generated per transaction, so for transactions |
| larger than fifo size READ COUNT must be disabled. |
| For those transactions we usually move to Data Mover mode. |
| */ |
| if (read_count <= dd->input_fifo_size) { |
| writel_relaxed(read_count, |
| dd->base + SPI_MX_READ_COUNT); |
| msm_spi_set_write_count(dd, read_count); |
| } else { |
| writel_relaxed(0, dd->base + SPI_MX_READ_COUNT); |
| msm_spi_set_write_count(dd, 0); |
| } |
| } else { |
| dd->mode = SPI_DMOV_MODE; |
| if (dd->write_len && dd->read_len) { |
| dd->tx_bytes_remaining = dd->write_len; |
| dd->rx_bytes_remaining = dd->read_len; |
| } |
| } |
| |
| /* Write mode - fifo or data mover*/ |
| spi_iom = readl_relaxed(dd->base + SPI_IO_MODES); |
| spi_iom &= ~(SPI_IO_M_INPUT_MODE | SPI_IO_M_OUTPUT_MODE); |
| spi_iom = (spi_iom | (dd->mode << OUTPUT_MODE_SHIFT)); |
| spi_iom = (spi_iom | (dd->mode << INPUT_MODE_SHIFT)); |
| /* Turn on packing for data mover */ |
| if (dd->mode == SPI_DMOV_MODE) |
| spi_iom |= SPI_IO_M_PACK_EN | SPI_IO_M_UNPACK_EN; |
| else |
| spi_iom &= ~(SPI_IO_M_PACK_EN | SPI_IO_M_UNPACK_EN); |
| writel_relaxed(spi_iom, dd->base + SPI_IO_MODES); |
| |
| msm_spi_set_config(dd, bpw); |
| |
| spi_ioc = readl_relaxed(dd->base + SPI_IO_CONTROL); |
| spi_ioc_orig = spi_ioc; |
| if (dd->cur_msg->spi->mode & SPI_CPOL) |
| spi_ioc |= SPI_IO_C_CLK_IDLE_HIGH; |
| else |
| spi_ioc &= ~SPI_IO_C_CLK_IDLE_HIGH; |
| chip_select = dd->cur_msg->spi->chip_select << 2; |
| if ((spi_ioc & SPI_IO_C_CS_SELECT) != chip_select) |
| spi_ioc = (spi_ioc & ~SPI_IO_C_CS_SELECT) | chip_select; |
| if (!dd->cur_transfer->cs_change) |
| spi_ioc |= SPI_IO_C_MX_CS_MODE; |
| if (spi_ioc != spi_ioc_orig) |
| writel_relaxed(spi_ioc, dd->base + SPI_IO_CONTROL); |
| |
| if (dd->mode == SPI_DMOV_MODE) { |
| msm_spi_setup_dm_transfer(dd); |
| msm_spi_enqueue_dm_commands(dd); |
| } |
| /* The output fifo interrupt handler will handle all writes after |
| the first. Restricting this to one write avoids contention |
| issues and race conditions between this thread and the int handler |
| */ |
| else if (dd->mode == SPI_FIFO_MODE) { |
| if (msm_spi_prepare_for_write(dd)) |
| goto transfer_end; |
| msm_spi_start_write(dd, read_count); |
| } |
| |
| /* Only enter the RUN state after the first word is written into |
| the output FIFO. Otherwise, the output FIFO EMPTY interrupt |
| might fire before the first word is written resulting in a |
| possible race condition. |
| */ |
| if (msm_spi_set_state(dd, SPI_OP_STATE_RUN)) |
| goto transfer_end; |
| |
| timeout = 100 * msecs_to_jiffies( |
| DIV_ROUND_UP(dd->cur_msg_len * 8, |
| DIV_ROUND_UP(max_speed, MSEC_PER_SEC))); |
| |
| /* Assume success, this might change later upon transaction result */ |
| dd->cur_msg->status = 0; |
| do { |
| if (!wait_for_completion_timeout(&dd->transfer_complete, |
| timeout)) { |
| dev_err(dd->dev, "%s: SPI transaction " |
| "timeout\n", __func__); |
| dd->cur_msg->status = -EIO; |
| if (dd->mode == SPI_DMOV_MODE) { |
| msm_dmov_flush(dd->tx_dma_chan); |
| msm_dmov_flush(dd->rx_dma_chan); |
| } |
| break; |
| } |
| } while (msm_spi_dm_send_next(dd)); |
| |
| transfer_end: |
| if (dd->mode == SPI_DMOV_MODE) |
| msm_spi_unmap_dma_buffers(dd); |
| dd->mode = SPI_MODE_NONE; |
| |
| msm_spi_set_state(dd, SPI_OP_STATE_RESET); |
| writel_relaxed(spi_ioc & ~SPI_IO_C_MX_CS_MODE, |
| dd->base + SPI_IO_CONTROL); |
| } |
| |
| static void get_transfer_length(struct msm_spi *dd) |
| { |
| struct spi_transfer *tr; |
| int num_xfrs = 0; |
| int readlen = 0; |
| int writelen = 0; |
| |
| dd->cur_msg_len = 0; |
| dd->multi_xfr = 0; |
| dd->read_len = dd->write_len = 0; |
| |
| list_for_each_entry(tr, &dd->cur_msg->transfers, transfer_list) { |
| if (tr->tx_buf) |
| writelen += tr->len; |
| if (tr->rx_buf) |
| readlen += tr->len; |
| dd->cur_msg_len += tr->len; |
| num_xfrs++; |
| } |
| |
| if (num_xfrs == 2) { |
| struct spi_transfer *first_xfr = dd->cur_transfer; |
| |
| dd->multi_xfr = 1; |
| tr = list_entry(first_xfr->transfer_list.next, |
| struct spi_transfer, |
| transfer_list); |
| /* |
| * We update dd->read_len and dd->write_len only |
| * for WR-WR and WR-RD transfers. |
| */ |
| if ((first_xfr->tx_buf) && (!first_xfr->rx_buf)) { |
| if (((tr->tx_buf) && (!tr->rx_buf)) || |
| ((!tr->tx_buf) && (tr->rx_buf))) { |
| dd->read_len = readlen; |
| dd->write_len = writelen; |
| } |
| } |
| } else if (num_xfrs > 1) |
| dd->multi_xfr = 1; |
| } |
| |
| static inline int combine_transfers(struct msm_spi *dd) |
| { |
| struct spi_transfer *t = dd->cur_transfer; |
| struct spi_transfer *nxt; |
| int xfrs_grped = 1; |
| |
| dd->cur_msg_len = dd->cur_transfer->len; |
| while (t->transfer_list.next != &dd->cur_msg->transfers) { |
| nxt = list_entry(t->transfer_list.next, |
| struct spi_transfer, |
| transfer_list); |
| if (t->cs_change != nxt->cs_change) |
| return xfrs_grped; |
| dd->cur_msg_len += nxt->len; |
| xfrs_grped++; |
| t = nxt; |
| } |
| return xfrs_grped; |
| } |
| |
| static void msm_spi_process_message(struct msm_spi *dd) |
| { |
| int xfrs_grped = 0; |
| int cs_num; |
| int rc; |
| |
| dd->write_xfr_cnt = dd->read_xfr_cnt = 0; |
| cs_num = dd->cur_msg->spi->chip_select; |
| if ((!(dd->cur_msg->spi->mode & SPI_LOOP)) && |
| (!(dd->cs_gpios[cs_num].valid)) && |
| (dd->cs_gpios[cs_num].gpio_num >= 0)) { |
| rc = gpio_request(dd->cs_gpios[cs_num].gpio_num, |
| spi_cs_rsrcs[cs_num]); |
| if (rc) { |
| dev_err(dd->dev, "gpio_request for pin %d failed with " |
| "error %d\n", dd->cs_gpios[cs_num].gpio_num, |
| rc); |
| return; |
| } |
| dd->cs_gpios[cs_num].valid = 1; |
| } |
| |
| dd->cur_transfer = list_first_entry(&dd->cur_msg->transfers, |
| struct spi_transfer, |
| transfer_list); |
| get_transfer_length(dd); |
| if (dd->multi_xfr && !dd->read_len && !dd->write_len) { |
| /* Handling of multi-transfers. FIFO mode is used by default */ |
| list_for_each_entry(dd->cur_transfer, |
| &dd->cur_msg->transfers, |
| transfer_list) { |
| if (!dd->cur_transfer->len) |
| goto error; |
| if (xfrs_grped) { |
| xfrs_grped--; |
| continue; |
| } else { |
| dd->read_len = dd->write_len = 0; |
| xfrs_grped = combine_transfers(dd); |
| } |
| dd->cur_tx_transfer = dd->cur_transfer; |
| dd->cur_rx_transfer = dd->cur_transfer; |
| msm_spi_process_transfer(dd); |
| xfrs_grped--; |
| } |
| } else { |
| /* Handling of a single transfer or WR-WR or WR-RD transfers */ |
| if ((!dd->cur_msg->is_dma_mapped) && |
| (msm_use_dm(dd, dd->cur_transfer, |
| dd->cur_transfer->bits_per_word))) { |
| /* Mapping of DMA buffers */ |
| int ret = msm_spi_map_dma_buffers(dd); |
| if (ret < 0) { |
| dd->cur_msg->status = ret; |
| goto error; |
| } |
| } |
| dd->cur_tx_transfer = dd->cur_rx_transfer = dd->cur_transfer; |
| msm_spi_process_transfer(dd); |
| } |
| |
| return; |
| |
| error: |
| if (dd->cs_gpios[cs_num].valid) { |
| gpio_free(dd->cs_gpios[cs_num].gpio_num); |
| dd->cs_gpios[cs_num].valid = 0; |
| } |
| } |
| |
| /* workqueue - pull messages from queue & process */ |
| static void msm_spi_workq(struct work_struct *work) |
| { |
| struct msm_spi *dd = |
| container_of(work, struct msm_spi, work_data); |
| unsigned long flags; |
| u32 status_error = 0; |
| |
| mutex_lock(&dd->core_lock); |
| |
| /* Don't allow power collapse until we release mutex */ |
| if (pm_qos_request_active(&qos_req_list)) |
| pm_qos_update_request(&qos_req_list, |
| dd->pm_lat); |
| if (dd->use_rlock) |
| remote_mutex_lock(&dd->r_lock); |
| |
| clk_enable(dd->clk); |
| clk_enable(dd->pclk); |
| msm_spi_enable_irqs(dd); |
| |
| if (!msm_spi_is_valid_state(dd)) { |
| dev_err(dd->dev, "%s: SPI operational state not valid\n", |
| __func__); |
| status_error = 1; |
| } |
| |
| spin_lock_irqsave(&dd->queue_lock, flags); |
| while (!list_empty(&dd->queue)) { |
| dd->cur_msg = list_entry(dd->queue.next, |
| struct spi_message, queue); |
| list_del_init(&dd->cur_msg->queue); |
| spin_unlock_irqrestore(&dd->queue_lock, flags); |
| if (status_error) |
| dd->cur_msg->status = -EIO; |
| else |
| msm_spi_process_message(dd); |
| if (dd->cur_msg->complete) |
| dd->cur_msg->complete(dd->cur_msg->context); |
| spin_lock_irqsave(&dd->queue_lock, flags); |
| } |
| dd->transfer_pending = 0; |
| spin_unlock_irqrestore(&dd->queue_lock, flags); |
| |
| msm_spi_disable_irqs(dd); |
| clk_disable(dd->clk); |
| clk_disable(dd->pclk); |
| |
| if (dd->use_rlock) |
| remote_mutex_unlock(&dd->r_lock); |
| |
| if (pm_qos_request_active(&qos_req_list)) |
| pm_qos_update_request(&qos_req_list, |
| PM_QOS_DEFAULT_VALUE); |
| |
| mutex_unlock(&dd->core_lock); |
| /* If needed, this can be done after the current message is complete, |
| and work can be continued upon resume. No motivation for now. */ |
| if (dd->suspended) |
| wake_up_interruptible(&dd->continue_suspend); |
| } |
| |
| static int msm_spi_transfer(struct spi_device *spi, struct spi_message *msg) |
| { |
| struct msm_spi *dd; |
| unsigned long flags; |
| struct spi_transfer *tr; |
| |
| dd = spi_master_get_devdata(spi->master); |
| if (dd->suspended) |
| return -EBUSY; |
| |
| if (list_empty(&msg->transfers) || !msg->complete) |
| return -EINVAL; |
| |
| list_for_each_entry(tr, &msg->transfers, transfer_list) { |
| /* Check message parameters */ |
| if (tr->speed_hz > dd->pdata->max_clock_speed || |
| (tr->bits_per_word && |
| (tr->bits_per_word < 4 || tr->bits_per_word > 32)) || |
| (tr->tx_buf == NULL && tr->rx_buf == NULL)) { |
| dev_err(&spi->dev, "Invalid transfer: %d Hz, %d bpw" |
| "tx=%p, rx=%p\n", |
| tr->speed_hz, tr->bits_per_word, |
| tr->tx_buf, tr->rx_buf); |
| return -EINVAL; |
| } |
| } |
| |
| spin_lock_irqsave(&dd->queue_lock, flags); |
| if (dd->suspended) { |
| spin_unlock_irqrestore(&dd->queue_lock, flags); |
| return -EBUSY; |
| } |
| dd->transfer_pending = 1; |
| list_add_tail(&msg->queue, &dd->queue); |
| spin_unlock_irqrestore(&dd->queue_lock, flags); |
| queue_work(dd->workqueue, &dd->work_data); |
| return 0; |
| } |
| |
| static int msm_spi_setup(struct spi_device *spi) |
| { |
| struct msm_spi *dd; |
| int rc = 0; |
| u32 spi_ioc; |
| u32 spi_config; |
| u32 mask; |
| |
| if (spi->bits_per_word < 4 || spi->bits_per_word > 32) { |
| dev_err(&spi->dev, "%s: invalid bits_per_word %d\n", |
| __func__, spi->bits_per_word); |
| rc = -EINVAL; |
| } |
| if (spi->chip_select > SPI_NUM_CHIPSELECTS-1) { |
| dev_err(&spi->dev, "%s, chip select %d exceeds max value %d\n", |
| __func__, spi->chip_select, SPI_NUM_CHIPSELECTS - 1); |
| rc = -EINVAL; |
| } |
| |
| if (rc) |
| goto err_setup_exit; |
| |
| dd = spi_master_get_devdata(spi->master); |
| |
| mutex_lock(&dd->core_lock); |
| if (dd->suspended) { |
| mutex_unlock(&dd->core_lock); |
| return -EBUSY; |
| } |
| |
| if (dd->use_rlock) |
| remote_mutex_lock(&dd->r_lock); |
| |
| clk_enable(dd->clk); |
| clk_enable(dd->pclk); |
| |
| spi_ioc = readl_relaxed(dd->base + SPI_IO_CONTROL); |
| mask = SPI_IO_C_CS_N_POLARITY_0 << spi->chip_select; |
| if (spi->mode & SPI_CS_HIGH) |
| spi_ioc |= mask; |
| else |
| spi_ioc &= ~mask; |
| if (spi->mode & SPI_CPOL) |
| spi_ioc |= SPI_IO_C_CLK_IDLE_HIGH; |
| else |
| spi_ioc &= ~SPI_IO_C_CLK_IDLE_HIGH; |
| |
| writel_relaxed(spi_ioc, dd->base + SPI_IO_CONTROL); |
| |
| spi_config = readl_relaxed(dd->base + SPI_CONFIG); |
| if (spi->mode & SPI_LOOP) |
| spi_config |= SPI_CFG_LOOPBACK; |
| else |
| spi_config &= ~SPI_CFG_LOOPBACK; |
| if (spi->mode & SPI_CPHA) |
| spi_config &= ~SPI_CFG_INPUT_FIRST; |
| else |
| spi_config |= SPI_CFG_INPUT_FIRST; |
| writel_relaxed(spi_config, dd->base + SPI_CONFIG); |
| |
| /* Ensure previous write completed before disabling the clocks */ |
| mb(); |
| clk_disable(dd->clk); |
| clk_disable(dd->pclk); |
| |
| if (dd->use_rlock) |
| remote_mutex_unlock(&dd->r_lock); |
| mutex_unlock(&dd->core_lock); |
| |
| err_setup_exit: |
| return rc; |
| } |
| |
| #ifdef CONFIG_DEBUG_FS |
| static int debugfs_iomem_x32_set(void *data, u64 val) |
| { |
| writel_relaxed(val, data); |
| /* Ensure the previous write completed. */ |
| mb(); |
| return 0; |
| } |
| |
| static int debugfs_iomem_x32_get(void *data, u64 *val) |
| { |
| *val = readl_relaxed(data); |
| /* Ensure the previous read completed. */ |
| mb(); |
| return 0; |
| } |
| |
| DEFINE_SIMPLE_ATTRIBUTE(fops_iomem_x32, debugfs_iomem_x32_get, |
| debugfs_iomem_x32_set, "0x%08llx\n"); |
| |
| static void spi_debugfs_init(struct msm_spi *dd) |
| { |
| dd->dent_spi = debugfs_create_dir(dev_name(dd->dev), NULL); |
| if (dd->dent_spi) { |
| int i; |
| for (i = 0; i < ARRAY_SIZE(debugfs_spi_regs); i++) { |
| dd->debugfs_spi_regs[i] = |
| debugfs_create_file( |
| debugfs_spi_regs[i].name, |
| debugfs_spi_regs[i].mode, |
| dd->dent_spi, |
| dd->base + debugfs_spi_regs[i].offset, |
| &fops_iomem_x32); |
| } |
| } |
| } |
| |
| static void spi_debugfs_exit(struct msm_spi *dd) |
| { |
| if (dd->dent_spi) { |
| int i; |
| debugfs_remove_recursive(dd->dent_spi); |
| dd->dent_spi = NULL; |
| for (i = 0; i < ARRAY_SIZE(debugfs_spi_regs); i++) |
| dd->debugfs_spi_regs[i] = NULL; |
| } |
| } |
| #else |
| static void spi_debugfs_init(struct msm_spi *dd) {} |
| static void spi_debugfs_exit(struct msm_spi *dd) {} |
| #endif |
| |
| /* ===Device attributes begin=== */ |
| static ssize_t show_stats(struct device *dev, struct device_attribute *attr, |
| char *buf) |
| { |
| struct spi_master *master = dev_get_drvdata(dev); |
| struct msm_spi *dd = spi_master_get_devdata(master); |
| |
| return snprintf(buf, PAGE_SIZE, |
| "Device %s\n" |
| "rx fifo_size = %d spi words\n" |
| "tx fifo_size = %d spi words\n" |
| "use_dma ? %s\n" |
| "rx block size = %d bytes\n" |
| "tx block size = %d bytes\n" |
| "burst size = %d bytes\n" |
| "DMA configuration:\n" |
| "tx_ch=%d, rx_ch=%d, tx_crci= %d, rx_crci=%d\n" |
| "--statistics--\n" |
| "Rx isrs = %d\n" |
| "Tx isrs = %d\n" |
| "DMA error = %d\n" |
| "--debug--\n" |
| "NA yet\n", |
| dev_name(dev), |
| dd->input_fifo_size, |
| dd->output_fifo_size, |
| dd->use_dma ? "yes" : "no", |
| dd->input_block_size, |
| dd->output_block_size, |
| dd->burst_size, |
| dd->tx_dma_chan, |
| dd->rx_dma_chan, |
| dd->tx_dma_crci, |
| dd->rx_dma_crci, |
| dd->stat_rx + dd->stat_dmov_rx, |
| dd->stat_tx + dd->stat_dmov_tx, |
| dd->stat_dmov_tx_err + dd->stat_dmov_rx_err |
| ); |
| } |
| |
| /* Reset statistics on write */ |
| static ssize_t set_stats(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct msm_spi *dd = dev_get_drvdata(dev); |
| dd->stat_rx = 0; |
| dd->stat_tx = 0; |
| dd->stat_dmov_rx = 0; |
| dd->stat_dmov_tx = 0; |
| dd->stat_dmov_rx_err = 0; |
| dd->stat_dmov_tx_err = 0; |
| return count; |
| } |
| |
| static DEVICE_ATTR(stats, S_IRUGO | S_IWUSR, show_stats, set_stats); |
| |
| static struct attribute *dev_attrs[] = { |
| &dev_attr_stats.attr, |
| NULL, |
| }; |
| |
| static struct attribute_group dev_attr_grp = { |
| .attrs = dev_attrs, |
| }; |
| /* ===Device attributes end=== */ |
| |
| /** |
| * spi_dmov_tx_complete_func - DataMover tx completion callback |
| * |
| * Executed in IRQ context (Data Mover's IRQ) DataMover's |
| * spinlock @msm_dmov_lock held. |
| */ |
| static void spi_dmov_tx_complete_func(struct msm_dmov_cmd *cmd, |
| unsigned int result, |
| struct msm_dmov_errdata *err) |
| { |
| struct msm_spi *dd; |
| |
| if (!(result & DMOV_RSLT_VALID)) { |
| pr_err("Invalid DMOV result: rc=0x%08x, cmd = %p", result, cmd); |
| return; |
| } |
| /* restore original context */ |
| dd = container_of(cmd, struct msm_spi, tx_hdr); |
| if (result & DMOV_RSLT_DONE) |
| dd->stat_dmov_tx++; |
| else { |
| /* Error or flush */ |
| if (result & DMOV_RSLT_ERROR) { |
| dev_err(dd->dev, "DMA error (0x%08x)\n", result); |
| dd->stat_dmov_tx_err++; |
| } |
| if (result & DMOV_RSLT_FLUSH) { |
| /* |
| * Flushing normally happens in process of |
| * removing, when we are waiting for outstanding |
| * DMA commands to be flushed. |
| */ |
| dev_info(dd->dev, |
| "DMA channel flushed (0x%08x)\n", result); |
| } |
| if (err) |
| dev_err(dd->dev, |
| "Flush data(%08x %08x %08x %08x %08x %08x)\n", |
| err->flush[0], err->flush[1], err->flush[2], |
| err->flush[3], err->flush[4], err->flush[5]); |
| dd->cur_msg->status = -EIO; |
| complete(&dd->transfer_complete); |
| } |
| } |
| |
| /** |
| * spi_dmov_rx_complete_func - DataMover rx completion callback |
| * |
| * Executed in IRQ context (Data Mover's IRQ) |
| * DataMover's spinlock @msm_dmov_lock held. |
| */ |
| static void spi_dmov_rx_complete_func(struct msm_dmov_cmd *cmd, |
| unsigned int result, |
| struct msm_dmov_errdata *err) |
| { |
| struct msm_spi *dd; |
| |
| if (!(result & DMOV_RSLT_VALID)) { |
| pr_err("Invalid DMOV result(rc = 0x%08x, cmd = %p)", |
| result, cmd); |
| return; |
| } |
| /* restore original context */ |
| dd = container_of(cmd, struct msm_spi, rx_hdr); |
| if (result & DMOV_RSLT_DONE) { |
| dd->stat_dmov_rx++; |
| if (atomic_inc_return(&dd->rx_irq_called) == 1) |
| return; |
| complete(&dd->transfer_complete); |
| } else { |
| /** Error or flush */ |
| if (result & DMOV_RSLT_ERROR) { |
| dev_err(dd->dev, "DMA error(0x%08x)\n", result); |
| dd->stat_dmov_rx_err++; |
| } |
| if (result & DMOV_RSLT_FLUSH) { |
| dev_info(dd->dev, |
| "DMA channel flushed(0x%08x)\n", result); |
| } |
| if (err) |
| dev_err(dd->dev, |
| "Flush data(%08x %08x %08x %08x %08x %08x)\n", |
| err->flush[0], err->flush[1], err->flush[2], |
| err->flush[3], err->flush[4], err->flush[5]); |
| dd->cur_msg->status = -EIO; |
| complete(&dd->transfer_complete); |
| } |
| } |
| |
| static inline u32 get_chunk_size(struct msm_spi *dd) |
| { |
| u32 cache_line = dma_get_cache_alignment(); |
| |
| return (roundup(sizeof(struct spi_dmov_cmd), DM_BYTE_ALIGN) + |
| roundup(dd->burst_size, cache_line))*2; |
| } |
| |
| static void msm_spi_teardown_dma(struct msm_spi *dd) |
| { |
| int limit = 0; |
| |
| if (!dd->use_dma) |
| return; |
| |
| while (dd->mode == SPI_DMOV_MODE && limit++ < 50) { |
| msm_dmov_flush(dd->tx_dma_chan); |
| msm_dmov_flush(dd->rx_dma_chan); |
| msleep(10); |
| } |
| |
| dma_free_coherent(NULL, get_chunk_size(dd), dd->tx_dmov_cmd, |
| dd->tx_dmov_cmd_dma); |
| dd->tx_dmov_cmd = dd->rx_dmov_cmd = NULL; |
| dd->tx_padding = dd->rx_padding = NULL; |
| } |
| |
| static __init int msm_spi_init_dma(struct msm_spi *dd) |
| { |
| dmov_box *box; |
| u32 cache_line = dma_get_cache_alignment(); |
| |
| /* Allocate all as one chunk, since all is smaller than page size */ |
| |
| /* We send NULL device, since it requires coherent_dma_mask id |
| device definition, we're okay with using system pool */ |
| dd->tx_dmov_cmd = dma_alloc_coherent(NULL, get_chunk_size(dd), |
| &dd->tx_dmov_cmd_dma, GFP_KERNEL); |
| if (dd->tx_dmov_cmd == NULL) |
| return -ENOMEM; |
| |
| /* DMA addresses should be 64 bit aligned aligned */ |
| dd->rx_dmov_cmd = (struct spi_dmov_cmd *) |
| ALIGN((size_t)&dd->tx_dmov_cmd[1], DM_BYTE_ALIGN); |
| dd->rx_dmov_cmd_dma = ALIGN(dd->tx_dmov_cmd_dma + |
| sizeof(struct spi_dmov_cmd), DM_BYTE_ALIGN); |
| |
| /* Buffers should be aligned to cache line */ |
| dd->tx_padding = (u8 *)ALIGN((size_t)&dd->rx_dmov_cmd[1], cache_line); |
| dd->tx_padding_dma = ALIGN(dd->rx_dmov_cmd_dma + |
| sizeof(struct spi_dmov_cmd), cache_line); |
| dd->rx_padding = (u8 *)ALIGN((size_t)(dd->tx_padding + dd->burst_size), |
| cache_line); |
| dd->rx_padding_dma = ALIGN(dd->tx_padding_dma + dd->burst_size, |
| cache_line); |
| |
| /* Setup DM commands */ |
| box = &(dd->rx_dmov_cmd->box); |
| box->cmd = CMD_MODE_BOX | CMD_SRC_CRCI(dd->rx_dma_crci); |
| box->src_row_addr = (uint32_t)dd->mem_phys_addr + SPI_INPUT_FIFO; |
| dd->rx_hdr.cmdptr = DMOV_CMD_PTR_LIST | |
| DMOV_CMD_ADDR(dd->rx_dmov_cmd_dma + |
| offsetof(struct spi_dmov_cmd, cmd_ptr)); |
| dd->rx_hdr.complete_func = spi_dmov_rx_complete_func; |
| |
| box = &(dd->tx_dmov_cmd->box); |
| box->cmd = CMD_MODE_BOX | CMD_DST_CRCI(dd->tx_dma_crci); |
| box->dst_row_addr = (uint32_t)dd->mem_phys_addr + SPI_OUTPUT_FIFO; |
| dd->tx_hdr.cmdptr = DMOV_CMD_PTR_LIST | |
| DMOV_CMD_ADDR(dd->tx_dmov_cmd_dma + |
| offsetof(struct spi_dmov_cmd, cmd_ptr)); |
| dd->tx_hdr.complete_func = spi_dmov_tx_complete_func; |
| |
| dd->tx_dmov_cmd->single_pad.cmd = CMD_MODE_SINGLE | CMD_LC | |
| CMD_DST_CRCI(dd->tx_dma_crci); |
| dd->tx_dmov_cmd->single_pad.dst = (uint32_t)dd->mem_phys_addr + |
| SPI_OUTPUT_FIFO; |
| dd->rx_dmov_cmd->single_pad.cmd = CMD_MODE_SINGLE | CMD_LC | |
| CMD_SRC_CRCI(dd->rx_dma_crci); |
| dd->rx_dmov_cmd->single_pad.src = (uint32_t)dd->mem_phys_addr + |
| SPI_INPUT_FIFO; |
| |
| /* Clear remaining activities on channel */ |
| msm_dmov_flush(dd->tx_dma_chan); |
| msm_dmov_flush(dd->rx_dma_chan); |
| |
| return 0; |
| } |
| |
| static int __init msm_spi_probe(struct platform_device *pdev) |
| { |
| struct spi_master *master; |
| struct msm_spi *dd; |
| struct resource *resource; |
| int rc = -ENXIO; |
| int locked = 0; |
| int i = 0; |
| int clk_enabled = 0; |
| int pclk_enabled = 0; |
| struct msm_spi_platform_data *pdata = pdev->dev.platform_data; |
| |
| master = spi_alloc_master(&pdev->dev, sizeof(struct msm_spi)); |
| if (!master) { |
| rc = -ENOMEM; |
| dev_err(&pdev->dev, "master allocation failed\n"); |
| goto err_probe_exit; |
| } |
| |
| master->bus_num = pdev->id; |
| master->mode_bits = SPI_SUPPORTED_MODES; |
| master->num_chipselect = SPI_NUM_CHIPSELECTS; |
| master->setup = msm_spi_setup; |
| master->transfer = msm_spi_transfer; |
| platform_set_drvdata(pdev, master); |
| dd = spi_master_get_devdata(master); |
| |
| dd->pdata = pdata; |
| rc = msm_spi_get_irq_data(dd, pdev); |
| if (rc) |
| goto err_probe_res; |
| resource = platform_get_resource_byname(pdev, |
| IORESOURCE_MEM, "spi_base"); |
| if (!resource) { |
| rc = -ENXIO; |
| goto err_probe_res; |
| } |
| dd->mem_phys_addr = resource->start; |
| dd->mem_size = resource_size(resource); |
| |
| rc = msm_spi_get_gsbi_resource(dd, pdev); |
| if (rc) |
| goto err_probe_res2; |
| |
| if (pdata) { |
| if (pdata->dma_config) { |
| rc = pdata->dma_config(); |
| if (rc) { |
| dev_warn(&pdev->dev, |
| "%s: DM mode not supported\n", |
| __func__); |
| dd->use_dma = 0; |
| goto skip_dma_resources; |
| } |
| } |
| resource = platform_get_resource_byname(pdev, |
| IORESOURCE_DMA, |
| "spidm_channels"); |
| if (resource) { |
| dd->rx_dma_chan = resource->start; |
| dd->tx_dma_chan = resource->end; |
| |
| resource = platform_get_resource_byname(pdev, |
| IORESOURCE_DMA, |
| "spidm_crci"); |
| if (!resource) { |
| rc = -ENXIO; |
| goto err_probe_res; |
| } |
| dd->rx_dma_crci = resource->start; |
| dd->tx_dma_crci = resource->end; |
| dd->use_dma = 1; |
| master->dma_alignment = dma_get_cache_alignment(); |
| } |
| |
| skip_dma_resources: |
| if (pdata->gpio_config) { |
| rc = pdata->gpio_config(); |
| if (rc) { |
| dev_err(&pdev->dev, |
| "%s: error configuring GPIOs\n", |
| __func__); |
| goto err_probe_gpio; |
| } |
| } |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(spi_rsrcs); ++i) { |
| resource = platform_get_resource_byname(pdev, IORESOURCE_IO, |
| spi_rsrcs[i]); |
| dd->spi_gpios[i] = resource ? resource->start : -1; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(spi_cs_rsrcs); ++i) { |
| resource = platform_get_resource_byname(pdev, IORESOURCE_IO, |
| spi_cs_rsrcs[i]); |
| dd->cs_gpios[i].gpio_num = resource ? resource->start : -1; |
| dd->cs_gpios[i].valid = 0; |
| } |
| |
| rc = msm_spi_request_gpios(dd); |
| if (rc) |
| goto err_probe_gpio; |
| |
| spin_lock_init(&dd->queue_lock); |
| mutex_init(&dd->core_lock); |
| INIT_LIST_HEAD(&dd->queue); |
| INIT_WORK(&dd->work_data, msm_spi_workq); |
| init_waitqueue_head(&dd->continue_suspend); |
| dd->workqueue = create_singlethread_workqueue( |
| dev_name(master->dev.parent)); |
| if (!dd->workqueue) |
| goto err_probe_workq; |
| |
| if (!request_mem_region(dd->mem_phys_addr, dd->mem_size, |
| SPI_DRV_NAME)) { |
| rc = -ENXIO; |
| goto err_probe_reqmem; |
| } |
| |
| dd->base = ioremap(dd->mem_phys_addr, dd->mem_size); |
| if (!dd->base) |
| goto err_probe_ioremap; |
| rc = msm_spi_request_gsbi(dd); |
| if (rc) |
| goto err_probe_ioremap2; |
| if (pdata && pdata->rsl_id) { |
| struct remote_mutex_id rmid; |
| rmid.r_spinlock_id = pdata->rsl_id; |
| rmid.delay_us = SPI_TRYLOCK_DELAY; |
| |
| rc = remote_mutex_init(&dd->r_lock, &rmid); |
| if (rc) { |
| dev_err(&pdev->dev, "%s: unable to init remote_mutex " |
| "(%s), (rc=%d)\n", rmid.r_spinlock_id, |
| __func__, rc); |
| goto err_probe_rlock_init; |
| } |
| dd->use_rlock = 1; |
| dd->pm_lat = pdata->pm_lat; |
| pm_qos_add_request(&qos_req_list, PM_QOS_CPU_DMA_LATENCY, |
| PM_QOS_DEFAULT_VALUE); |
| } |
| mutex_lock(&dd->core_lock); |
| if (dd->use_rlock) |
| remote_mutex_lock(&dd->r_lock); |
| locked = 1; |
| |
| dd->dev = &pdev->dev; |
| dd->clk = clk_get(&pdev->dev, "core_clk"); |
| if (IS_ERR(dd->clk)) { |
| dev_err(&pdev->dev, "%s: unable to get core_clk\n", __func__); |
| rc = PTR_ERR(dd->clk); |
| goto err_probe_clk_get; |
| } |
| |
| dd->pclk = clk_get(&pdev->dev, "iface_clk"); |
| if (IS_ERR(dd->pclk)) { |
| dev_err(&pdev->dev, "%s: unable to get iface_clk\n", __func__); |
| rc = PTR_ERR(dd->pclk); |
| goto err_probe_pclk_get; |
| } |
| |
| if (pdata && pdata->max_clock_speed) |
| msm_spi_clock_set(dd, dd->pdata->max_clock_speed); |
| |
| rc = clk_enable(dd->clk); |
| if (rc) { |
| dev_err(&pdev->dev, "%s: unable to enable core_clk\n", |
| __func__); |
| goto err_probe_clk_enable; |
| } |
| clk_enabled = 1; |
| |
| rc = clk_enable(dd->pclk); |
| if (rc) { |
| dev_err(&pdev->dev, "%s: unable to enable iface_clk\n", |
| __func__); |
| goto err_probe_pclk_enable; |
| } |
| pclk_enabled = 1; |
| msm_spi_init_gsbi(dd); |
| msm_spi_calculate_fifo_size(dd); |
| if (dd->use_dma) { |
| rc = msm_spi_init_dma(dd); |
| if (rc) |
| goto err_probe_dma; |
| } |
| |
| /* Initialize registers */ |
| writel_relaxed(0x00000001, dd->base + SPI_SW_RESET); |
| msm_spi_set_state(dd, SPI_OP_STATE_RESET); |
| |
| writel_relaxed(0x00000000, dd->base + SPI_OPERATIONAL); |
| writel_relaxed(0x00000000, dd->base + SPI_CONFIG); |
| writel_relaxed(0x00000000, dd->base + SPI_IO_MODES); |
| /* |
| * The SPI core generates a bogus input overrun error on some targets, |
| * when a transition from run to reset state occurs and if the FIFO has |
| * an odd number of entries. Hence we disable the INPUT_OVER_RUN_ERR_EN |
| * bit. |
| */ |
| msm_spi_enable_error_flags(dd); |
| |
| writel_relaxed(SPI_IO_C_NO_TRI_STATE, dd->base + SPI_IO_CONTROL); |
| rc = msm_spi_set_state(dd, SPI_OP_STATE_RESET); |
| if (rc) |
| goto err_probe_state; |
| |
| clk_disable(dd->clk); |
| clk_disable(dd->pclk); |
| clk_enabled = 0; |
| pclk_enabled = 0; |
| |
| dd->suspended = 0; |
| dd->transfer_pending = 0; |
| dd->multi_xfr = 0; |
| dd->mode = SPI_MODE_NONE; |
| |
| rc = msm_spi_request_irq(dd, pdev->name, master); |
| if (rc) |
| goto err_probe_irq; |
| |
| msm_spi_disable_irqs(dd); |
| if (dd->use_rlock) |
| remote_mutex_unlock(&dd->r_lock); |
| |
| mutex_unlock(&dd->core_lock); |
| locked = 0; |
| |
| rc = spi_register_master(master); |
| if (rc) |
| goto err_probe_reg_master; |
| |
| rc = sysfs_create_group(&(dd->dev->kobj), &dev_attr_grp); |
| if (rc) { |
| dev_err(&pdev->dev, "failed to create dev. attrs : %d\n", rc); |
| goto err_attrs; |
| } |
| |
| spi_debugfs_init(dd); |
| |
| return 0; |
| |
| err_attrs: |
| err_probe_reg_master: |
| msm_spi_free_irq(dd, master); |
| err_probe_irq: |
| err_probe_state: |
| msm_spi_teardown_dma(dd); |
| err_probe_dma: |
| if (pclk_enabled) |
| clk_disable(dd->pclk); |
| err_probe_pclk_enable: |
| if (clk_enabled) |
| clk_disable(dd->clk); |
| err_probe_clk_enable: |
| clk_put(dd->pclk); |
| err_probe_pclk_get: |
| clk_put(dd->clk); |
| err_probe_clk_get: |
| if (locked) { |
| if (dd->use_rlock) |
| remote_mutex_unlock(&dd->r_lock); |
| mutex_unlock(&dd->core_lock); |
| } |
| err_probe_rlock_init: |
| msm_spi_release_gsbi(dd); |
| err_probe_ioremap2: |
| iounmap(dd->base); |
| err_probe_ioremap: |
| release_mem_region(dd->mem_phys_addr, dd->mem_size); |
| err_probe_reqmem: |
| destroy_workqueue(dd->workqueue); |
| err_probe_workq: |
| msm_spi_free_gpios(dd); |
| err_probe_gpio: |
| if (pdata && pdata->gpio_release) |
| pdata->gpio_release(); |
| err_probe_res2: |
| err_probe_res: |
| spi_master_put(master); |
| err_probe_exit: |
| return rc; |
| } |
| |
| #ifdef CONFIG_PM |
| static int msm_spi_suspend(struct platform_device *pdev, pm_message_t state) |
| { |
| struct spi_master *master = platform_get_drvdata(pdev); |
| struct msm_spi *dd; |
| unsigned long flags; |
| |
| if (!master) |
| goto suspend_exit; |
| dd = spi_master_get_devdata(master); |
| if (!dd) |
| goto suspend_exit; |
| |
| /* Make sure nothing is added to the queue while we're suspending */ |
| spin_lock_irqsave(&dd->queue_lock, flags); |
| dd->suspended = 1; |
| spin_unlock_irqrestore(&dd->queue_lock, flags); |
| |
| /* Wait for transactions to end, or time out */ |
| wait_event_interruptible(dd->continue_suspend, !dd->transfer_pending); |
| msm_spi_free_gpios(dd); |
| |
| suspend_exit: |
| return 0; |
| } |
| |
| static int msm_spi_resume(struct platform_device *pdev) |
| { |
| struct spi_master *master = platform_get_drvdata(pdev); |
| struct msm_spi *dd; |
| |
| if (!master) |
| goto resume_exit; |
| dd = spi_master_get_devdata(master); |
| if (!dd) |
| goto resume_exit; |
| |
| BUG_ON(msm_spi_request_gpios(dd) != 0); |
| dd->suspended = 0; |
| resume_exit: |
| return 0; |
| } |
| #else |
| #define msm_spi_suspend NULL |
| #define msm_spi_resume NULL |
| #endif /* CONFIG_PM */ |
| |
| static int __devexit msm_spi_remove(struct platform_device *pdev) |
| { |
| struct spi_master *master = platform_get_drvdata(pdev); |
| struct msm_spi *dd = spi_master_get_devdata(master); |
| struct msm_spi_platform_data *pdata = pdev->dev.platform_data; |
| |
| pm_qos_remove_request(&qos_req_list); |
| spi_debugfs_exit(dd); |
| sysfs_remove_group(&pdev->dev.kobj, &dev_attr_grp); |
| |
| msm_spi_free_irq(dd, master); |
| msm_spi_teardown_dma(dd); |
| |
| if (pdata && pdata->gpio_release) |
| pdata->gpio_release(); |
| |
| msm_spi_free_gpios(dd); |
| iounmap(dd->base); |
| release_mem_region(dd->mem_phys_addr, dd->mem_size); |
| msm_spi_release_gsbi(dd); |
| clk_put(dd->clk); |
| clk_put(dd->pclk); |
| destroy_workqueue(dd->workqueue); |
| platform_set_drvdata(pdev, 0); |
| spi_unregister_master(master); |
| spi_master_put(master); |
| |
| return 0; |
| } |
| |
| static struct platform_driver msm_spi_driver = { |
| .driver = { |
| .name = SPI_DRV_NAME, |
| .owner = THIS_MODULE, |
| }, |
| .suspend = msm_spi_suspend, |
| .resume = msm_spi_resume, |
| .remove = __exit_p(msm_spi_remove), |
| }; |
| |
| static int __init msm_spi_init(void) |
| { |
| return platform_driver_probe(&msm_spi_driver, msm_spi_probe); |
| } |
| module_init(msm_spi_init); |
| |
| static void __exit msm_spi_exit(void) |
| { |
| platform_driver_unregister(&msm_spi_driver); |
| } |
| module_exit(msm_spi_exit); |