| # |
| # YAFFS file system configurations |
| # |
| |
| config YAFFS_FS |
| tristate "YAFFS2 file system support" |
| default n |
| depends on MTD_BLOCK |
| select YAFFS_YAFFS1 |
| select YAFFS_YAFFS2 |
| help |
| YAFFS2, or Yet Another Flash Filing System, is a filing system |
| optimised for NAND Flash chips. |
| |
| To compile the YAFFS2 file system support as a module, choose M |
| here: the module will be called yaffs2. |
| |
| If unsure, say N. |
| |
| Further information on YAFFS2 is available at |
| <http://www.aleph1.co.uk/yaffs/>. |
| |
| config YAFFS_YAFFS1 |
| bool "512 byte / page devices" |
| depends on YAFFS_FS |
| default y |
| help |
| Enable YAFFS1 support -- yaffs for 512 byte / page devices |
| |
| Not needed for 2K-page devices. |
| |
| If unsure, say Y. |
| |
| config YAFFS_9BYTE_TAGS |
| bool "Use older-style on-NAND data format with pageStatus byte" |
| depends on YAFFS_YAFFS1 |
| default n |
| help |
| |
| Older-style on-NAND data format has a "pageStatus" byte to record |
| chunk/page state. This byte is zero when the page is discarded. |
| Choose this option if you have existing on-NAND data using this |
| format that you need to continue to support. New data written |
| also uses the older-style format. Note: Use of this option |
| generally requires that MTD's oob layout be adjusted to use the |
| older-style format. See notes on tags formats and MTD versions |
| in yaffs_mtdif1.c. |
| |
| If unsure, say N. |
| |
| config YAFFS_DOES_ECC |
| bool "Lets Yaffs do its own ECC" |
| depends on YAFFS_FS && YAFFS_YAFFS1 && !YAFFS_9BYTE_TAGS |
| default n |
| help |
| This enables Yaffs to use its own ECC functions instead of using |
| the ones from the generic MTD-NAND driver. |
| |
| If unsure, say N. |
| |
| config YAFFS_ECC_WRONG_ORDER |
| bool "Use the same ecc byte order as Steven Hill's nand_ecc.c" |
| depends on YAFFS_FS && YAFFS_DOES_ECC && !YAFFS_9BYTE_TAGS |
| default n |
| help |
| This makes yaffs_ecc.c use the same ecc byte order as Steven |
| Hill's nand_ecc.c. If not set, then you get the same ecc byte |
| order as SmartMedia. |
| |
| If unsure, say N. |
| |
| config YAFFS_YAFFS2 |
| bool "2048 byte (or larger) / page devices" |
| depends on YAFFS_FS |
| default y |
| help |
| Enable YAFFS2 support -- yaffs for >= 2K bytes per page devices |
| |
| If unsure, say Y. |
| |
| config YAFFS_AUTO_YAFFS2 |
| bool "Autoselect yaffs2 format" |
| depends on YAFFS_YAFFS2 |
| default y |
| help |
| Without this, you need to explicitely use yaffs2 as the file |
| system type. With this, you can say "yaffs" and yaffs or yaffs2 |
| will be used depending on the device page size (yaffs on |
| 512-byte page devices, yaffs2 on 2K page devices). |
| |
| If unsure, say Y. |
| |
| config YAFFS_DISABLE_TAGS_ECC |
| bool "Disable YAFFS from doing ECC on tags by default" |
| depends on YAFFS_FS && YAFFS_YAFFS2 |
| default n |
| help |
| This defaults Yaffs to using its own ECC calculations on tags instead of |
| just relying on the MTD. |
| This behavior can also be overridden with tags_ecc_on and |
| tags_ecc_off mount options. |
| |
| If unsure, say N. |
| |
| config YAFFS_ALWAYS_CHECK_CHUNK_ERASED |
| bool "Force chunk erase check" |
| depends on YAFFS_FS |
| default n |
| help |
| Normally YAFFS only checks chunks before writing until an erased |
| chunk is found. This helps to detect any partially written |
| chunks that might have happened due to power loss. |
| |
| Enabling this forces on the test that chunks are erased in flash |
| before writing to them. This takes more time but is potentially |
| a bit more secure. |
| |
| Suggest setting Y during development and ironing out driver |
| issues etc. Suggest setting to N if you want faster writing. |
| |
| If unsure, say Y. |
| |
| config YAFFS_EMPTY_LOST_AND_FOUND |
| bool "Empty lost and found on boot" |
| depends on YAFFS_FS |
| default n |
| help |
| If this is enabled then the contents of lost and found is |
| automatically dumped at mount. |
| |
| If unsure, say N. |
| |
| config YAFFS_DISABLE_BLOCK_REFRESHING |
| bool "Disable yaffs2 block refreshing" |
| depends on YAFFS_FS |
| default n |
| help |
| If this is set, then block refreshing is disabled. |
| Block refreshing infrequently refreshes the oldest block in |
| a yaffs2 file system. This mechanism helps to refresh flash to |
| mitigate against data loss. This is particularly useful for MLC. |
| |
| If unsure, say N. |
| |
| config YAFFS_DISABLE_BACKGROUND |
| bool "Disable yaffs2 background processing" |
| depends on YAFFS_FS |
| default n |
| help |
| If this is set, then background processing is disabled. |
| Background processing makes many foreground activities faster. |
| |
| If unsure, say N. |
| |
| config YAFFS_XATTR |
| bool "Enable yaffs2 xattr support" |
| depends on YAFFS_FS |
| default y |
| help |
| If this is set then yaffs2 will provide xattr support. |
| If unsure, say Y. |