blob: a1c8923b0bf5ae95b52fe3e28b8c261e6db5609c [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001#
2# Video configuration
3#
4
5menu "Graphics support"
6
Antonino A. Daplasba707102006-06-26 00:26:37 -07007config FIRMWARE_EDID
8 bool "Enable firmware EDID"
9 default y
10 ---help---
11 This enables access to the EDID transferred from the firmware.
12 On the i386, this is from the Video BIOS. Enable this if DDC/I2C
13 transfers do not work for your driver and if you are using
14 nvidiafb, i810fb or savagefb.
15
16 In general, choosing Y for this option is safe. If you
17 experience extremely long delays while booting before you get
18 something on your display, try setting this to N. Matrox cards in
19 combination with certain motherboards and monitors are known to
20 suffer from this problem.
21
Linus Torvalds1da177e2005-04-16 15:20:36 -070022config FB
23 tristate "Support for frame buffer devices"
24 ---help---
25 The frame buffer device provides an abstraction for the graphics
26 hardware. It represents the frame buffer of some video hardware and
27 allows application software to access the graphics hardware through
28 a well-defined interface, so the software doesn't need to know
29 anything about the low-level (hardware register) stuff.
30
31 Frame buffer devices work identically across the different
32 architectures supported by Linux and make the implementation of
33 application programs easier and more portable; at this point, an X
34 server exists which uses the frame buffer device exclusively.
35 On several non-X86 architectures, the frame buffer device is the
36 only way to use the graphics hardware.
37
38 The device is accessed through special device nodes, usually located
39 in the /dev directory, i.e. /dev/fb*.
40
41 You need an utility program called fbset to make full use of frame
42 buffer devices. Please read <file:Documentation/fb/framebuffer.txt>
43 and the Framebuffer-HOWTO at
44 <http://www.tahallah.demon.co.uk/programming/prog.html> for more
45 information.
46
47 Say Y here and to the driver for your graphics board below if you
48 are compiling a kernel for a non-x86 architecture.
49
50 If you are compiling for the x86 architecture, you can say Y if you
51 want to play with it, but it is not essential. Please note that
52 running graphical applications that directly touch the hardware
53 (e.g. an accelerated X server) and that are not frame buffer
54 device-aware may cause unexpected results. If unsure, say N.
55
Dennis Munsiefc5891c2006-10-03 01:14:42 -070056config FB_DDC
57 tristate
58 depends on FB && I2C && I2C_ALGOBIT
59 default n
60
Linus Torvalds1da177e2005-04-16 15:20:36 -070061config FB_CFB_FILLRECT
62 tristate
63 depends on FB
64 default n
65 ---help---
66 Include the cfb_fillrect function for generic software rectangle
67 filling. This is used by drivers that don't provide their own
68 (accelerated) version.
69
70config FB_CFB_COPYAREA
71 tristate
72 depends on FB
73 default n
74 ---help---
75 Include the cfb_copyarea function for generic software area copying.
76 This is used by drivers that don't provide their own (accelerated)
77 version.
78
79config FB_CFB_IMAGEBLIT
80 tristate
81 depends on FB
82 default n
83 ---help---
84 Include the cfb_imageblit function for generic software image
85 blitting. This is used by drivers that don't provide their own
86 (accelerated) version.
87
Linus Torvalds1da177e2005-04-16 15:20:36 -070088config FB_MACMODES
89 tristate
90 depends on FB
91 default n
92
Michael Hanselmann5474c122006-06-25 05:47:08 -070093config FB_BACKLIGHT
Michael Hanselmann4b755992006-07-30 03:04:19 -070094 bool
95 depends on FB
96 select BACKLIGHT_LCD_SUPPORT
97 select BACKLIGHT_CLASS_DEVICE
98 default n
Michael Hanselmann5474c122006-06-25 05:47:08 -070099
Linus Torvalds1da177e2005-04-16 15:20:36 -0700100config FB_MODE_HELPERS
101 bool "Enable Video Mode Handling Helpers"
102 depends on FB
103 default n
104 ---help---
105 This enables functions for handling video modes using the
106 Generalized Timing Formula and the EDID parser. A few drivers rely
107 on this feature such as the radeonfb, rivafb, and the i810fb. If
108 your driver does not take advantage of this feature, choosing Y will
109 just increase the kernel size by about 5K.
110
111config FB_TILEBLITTING
112 bool "Enable Tile Blitting Support"
113 depends on FB
114 default n
115 ---help---
116 This enables tile blitting. Tile blitting is a drawing technique
117 where the screen is divided into rectangular sections (tiles), whereas
118 the standard blitting divides the screen into pixels. Because the
119 default drawing element is a tile, drawing functions will be passed
120 parameters in terms of number of tiles instead of number of pixels.
121 For example, to draw a single character, instead of using bitmaps,
122 an index to an array of bitmaps will be used. To clear or move a
123 rectangular section of a screen, the rectangle will be described in
124 terms of number of tiles in the x- and y-axis.
125
126 This is particularly important to one driver, matroxfb. If
127 unsure, say N.
128
129config FB_CIRRUS
130 tristate "Cirrus Logic support"
131 depends on FB && (ZORRO || PCI)
132 select FB_CFB_FILLRECT
133 select FB_CFB_COPYAREA
134 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700135 ---help---
136 This enables support for Cirrus Logic GD542x/543x based boards on
137 Amiga: SD64, Piccolo, Picasso II/II+, Picasso IV, or EGS Spectrum.
138
139 If you have a PCI-based system, this enables support for these
140 chips: GD-543x, GD-544x, GD-5480.
141
142 Please read the file <file:Documentation/fb/cirrusfb.txt>.
143
144 Say N unless you have such a graphics board or plan to get one
145 before you next recompile the kernel.
146
147config FB_PM2
148 tristate "Permedia2 support"
149 depends on FB && ((AMIGA && BROKEN) || PCI)
150 select FB_CFB_FILLRECT
151 select FB_CFB_COPYAREA
152 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700153 help
154 This is the frame buffer device driver for the Permedia2 AGP frame
155 buffer card from ASK, aka `Graphic Blaster Exxtreme'. There is a
156 product page at
157 <http://www.ask.com.hk/product/Permedia%202/permedia2.htm>.
158
159config FB_PM2_FIFO_DISCONNECT
160 bool "enable FIFO disconnect feature"
161 depends on FB_PM2 && PCI
162 help
163 Support the Permedia2 FIFO disconnect feature (see CONFIG_FB_PM2).
164
165config FB_ARMCLCD
166 tristate "ARM PrimeCell PL110 support"
167 depends on FB && ARM && ARM_AMBA
168 select FB_CFB_FILLRECT
169 select FB_CFB_COPYAREA
170 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700171 help
172 This framebuffer device driver is for the ARM PrimeCell PL110
173 Colour LCD controller. ARM PrimeCells provide the building
174 blocks for System on a Chip devices.
175
176 If you want to compile this as a module (=code which can be
177 inserted into and removed from the running kernel), say M
178 here and read <file:Documentation/modules.txt>. The module
179 will be called amba-clcd.
180
Marc Singer903e2bb2006-05-16 11:41:30 +0100181choice
182
183 depends on FB_ARMCLCD && (ARCH_LH7A40X || ARCH_LH7952X)
184 prompt "LCD Panel"
185 default FB_ARMCLCD_SHARP_LQ035Q7DB02
186
187config FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
188 bool "LogicPD LCD 3.5\" QVGA w/HRTFT IC"
189 help
190 This is an implementation of the Sharp LQ035Q7DB02, a 3.5"
191 color QVGA, HRTFT panel. The LogicPD device includes an
192 an integrated HRTFT controller IC.
193 The native resolution is 240x320.
194
195config FB_ARMCLCD_SHARP_LQ057Q3DC02
196 bool "LogicPD LCD 5.7\" QVGA"
197 help
198 This is an implementation of the Sharp LQ057Q3DC02, a 5.7"
199 color QVGA, TFT panel. The LogicPD device includes an
200 The native resolution is 320x240.
201
202config FB_ARMCLCD_SHARP_LQ64D343
203 bool "LogicPD LCD 6.4\" VGA"
204 help
205 This is an implementation of the Sharp LQ64D343, a 6.4"
206 color VGA, TFT panel. The LogicPD device includes an
207 The native resolution is 640x480.
208
209config FB_ARMCLCD_SHARP_LQ10D368
210 bool "LogicPD LCD 10.4\" VGA"
211 help
212 This is an implementation of the Sharp LQ10D368, a 10.4"
213 color VGA, TFT panel. The LogicPD device includes an
214 The native resolution is 640x480.
215
216
217config FB_ARMCLCD_SHARP_LQ121S1DG41
218 bool "LogicPD LCD 12.1\" SVGA"
219 help
220 This is an implementation of the Sharp LQ121S1DG41, a 12.1"
221 color SVGA, TFT panel. The LogicPD device includes an
222 The native resolution is 800x600.
223
224 This panel requires a clock rate may be an integer fraction
225 of the base LCDCLK frequency. The driver will select the
226 highest frequency available that is lower than the maximum
227 allowed. The panel may flicker if the clock rate is
228 slower than the recommended minimum.
229
230config FB_ARMCLCD_AUO_A070VW01_WIDE
231 bool "AU Optronics A070VW01 LCD 7.0\" WIDE"
232 help
233 This is an implementation of the AU Optronics, a 7.0"
234 WIDE Color. The native resolution is 234x480.
235
236config FB_ARMCLCD_HITACHI
237 bool "Hitachi Wide Screen 800x480"
238 help
239 This is an implementation of the Hitachi 800x480.
240
241endchoice
242
243
Linus Torvalds1da177e2005-04-16 15:20:36 -0700244config FB_ACORN
245 bool "Acorn VIDC support"
246 depends on (FB = y) && ARM && (ARCH_ACORN || ARCH_CLPS7500)
247 select FB_CFB_FILLRECT
248 select FB_CFB_COPYAREA
249 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700250 help
251 This is the frame buffer device driver for the Acorn VIDC graphics
252 hardware found in Acorn RISC PCs and other ARM-based machines. If
253 unsure, say N.
254
255config FB_CLPS711X
256 bool "CLPS711X LCD support"
257 depends on (FB = y) && ARM && ARCH_CLPS711X
258 select FB_CFB_FILLRECT
259 select FB_CFB_COPYAREA
260 select FB_CFB_IMAGEBLIT
Randy.Dunlape65c0852005-11-07 01:00:28 -0800261 help
262 Say Y to enable the Framebuffer driver for the CLPS7111 and
263 EP7212 processors.
Linus Torvalds1da177e2005-04-16 15:20:36 -0700264
265config FB_SA1100
266 bool "SA-1100 LCD support"
267 depends on (FB = y) && ARM && ARCH_SA1100
268 select FB_CFB_FILLRECT
269 select FB_CFB_COPYAREA
270 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700271 help
272 This is a framebuffer device for the SA-1100 LCD Controller.
273 See <http://www.linux-fbdev.org/> for information on framebuffer
274 devices.
275
276 If you plan to use the LCD display with your SA-1100 system, say
277 Y here.
278
Sascha Hauer7c2f891c2005-05-01 08:59:24 -0700279config FB_IMX
280 tristate "Motorola i.MX LCD support"
281 depends on FB && ARM && ARCH_IMX
282 select FB_CFB_FILLRECT
283 select FB_CFB_COPYAREA
284 select FB_CFB_IMAGEBLIT
Sascha Hauer7c2f891c2005-05-01 08:59:24 -0700285
Linus Torvalds1da177e2005-04-16 15:20:36 -0700286config FB_CYBER2000
287 tristate "CyberPro 2000/2010/5000 support"
288 depends on FB && PCI && (BROKEN || !SPARC64)
289 select FB_CFB_FILLRECT
290 select FB_CFB_COPYAREA
291 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700292 help
293 This enables support for the Integraphics CyberPro 20x0 and 5000
294 VGA chips used in the Rebel.com Netwinder and other machines.
295 Say Y if you have a NetWinder or a graphics card containing this
296 device, otherwise say N.
297
298config FB_APOLLO
299 bool
300 depends on (FB = y) && APOLLO
301 default y
302 select FB_CFB_FILLRECT
303 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700304
305config FB_Q40
306 bool
307 depends on (FB = y) && Q40
308 default y
309 select FB_CFB_FILLRECT
310 select FB_CFB_COPYAREA
311 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700312
313config FB_AMIGA
314 tristate "Amiga native chipset support"
315 depends on FB && AMIGA
Linus Torvalds1da177e2005-04-16 15:20:36 -0700316 help
317 This is the frame buffer device driver for the builtin graphics
318 chipset found in Amigas.
319
320 To compile this driver as a module, choose M here: the
321 module will be called amifb.
322
323config FB_AMIGA_OCS
324 bool "Amiga OCS chipset support"
325 depends on FB_AMIGA
326 help
327 This enables support for the original Agnus and Denise video chips,
328 found in the Amiga 1000 and most A500's and A2000's. If you intend
329 to run Linux on any of these systems, say Y; otherwise say N.
330
331config FB_AMIGA_ECS
332 bool "Amiga ECS chipset support"
333 depends on FB_AMIGA
334 help
335 This enables support for the Enhanced Chip Set, found in later
336 A500's, later A2000's, the A600, the A3000, the A3000T and CDTV. If
337 you intend to run Linux on any of these systems, say Y; otherwise
338 say N.
339
340config FB_AMIGA_AGA
341 bool "Amiga AGA chipset support"
342 depends on FB_AMIGA
343 help
344 This enables support for the Advanced Graphics Architecture (also
345 known as the AGA or AA) Chip Set, found in the A1200, A4000, A4000T
346 and CD32. If you intend to run Linux on any of these systems, say Y;
347 otherwise say N.
348
349config FB_CYBER
350 tristate "Amiga CyberVision 64 support"
351 depends on FB && ZORRO && BROKEN
352 select FB_CFB_FILLRECT
353 select FB_CFB_COPYAREA
354 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700355 help
356 This enables support for the Cybervision 64 graphics card from
357 Phase5. Please note that its use is not all that intuitive (i.e. if
358 you have any questions, be sure to ask!). Say N unless you have a
359 Cybervision 64 or plan to get one before you next recompile the
360 kernel. Please note that this driver DOES NOT support the
361 Cybervision 64/3D card, as they use incompatible video chips.
362
363config FB_VIRGE
364 bool "Amiga CyberVision 64/3D support "
365 depends on (FB = y) && ZORRO && BROKEN
366 select FB_CFB_FILLRECT
367 select FB_CFB_COPYAREA
368 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700369 help
370 This enables support for the Cybervision 64/3D graphics card from
371 Phase5. Please note that its use is not all that intuitive (i.e. if
372 you have any questions, be sure to ask!). Say N unless you have a
373 Cybervision 64/3D or plan to get one before you next recompile the
374 kernel. Please note that this driver DOES NOT support the older
375 Cybervision 64 card, as they use incompatible video chips.
376
377config FB_RETINAZ3
378 tristate "Amiga Retina Z3 support"
379 depends on (FB = y) && ZORRO && BROKEN
380 help
381 This enables support for the Retina Z3 graphics card. Say N unless
382 you have a Retina Z3 or plan to get one before you next recompile
383 the kernel.
384
385config FB_FM2
386 bool "Amiga FrameMaster II/Rainbow II support"
387 depends on (FB = y) && ZORRO
388 select FB_CFB_FILLRECT
389 select FB_CFB_COPYAREA
390 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700391 help
392 This is the frame buffer device driver for the Amiga FrameMaster
393 card from BSC (exhibited 1992 but not shipped as a CBM product).
394
Jaya Kumar1154ea72005-06-21 17:17:04 -0700395config FB_ARC
396 tristate "Arc Monochrome LCD board support"
397 depends on FB && X86
398 select FB_CFB_FILLRECT
399 select FB_CFB_COPYAREA
400 select FB_CFB_IMAGEBLIT
Jaya Kumar1154ea72005-06-21 17:17:04 -0700401 help
402 This enables support for the Arc Monochrome LCD board. The board
403 is based on the KS-108 lcd controller and is typically a matrix
404 of 2*n chips. This driver was tested with a 128x64 panel. This
405 driver supports it for use with x86 SBCs through a 16 bit GPIO
406 interface (8 bit data, 8 bit control). If you anticpate using
407 this driver, say Y or M; otherwise say N. You must specify the
408 GPIO IO address to be used for setting control and data.
409
Linus Torvalds1da177e2005-04-16 15:20:36 -0700410config FB_ATARI
411 bool "Atari native chipset support"
412 depends on (FB = y) && ATARI && BROKEN
413 help
414 This is the frame buffer device driver for the builtin graphics
415 chipset found in Ataris.
416
417config FB_OF
418 bool "Open Firmware frame buffer device support"
419 depends on (FB = y) && (PPC64 || PPC_OF)
420 select FB_CFB_FILLRECT
421 select FB_CFB_COPYAREA
422 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700423 select FB_MACMODES
424 help
425 Say Y if you want support with Open Firmware for your graphics
426 board.
427
428config FB_CONTROL
429 bool "Apple \"control\" display support"
Olaf Heringa04b61d2006-07-30 03:03:52 -0700430 depends on (FB = y) && PPC_PMAC && PPC32
Linus Torvalds1da177e2005-04-16 15:20:36 -0700431 select FB_CFB_FILLRECT
432 select FB_CFB_COPYAREA
433 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700434 select FB_MACMODES
435 help
436 This driver supports a frame buffer for the graphics adapter in the
437 Power Macintosh 7300 and others.
438
439config FB_PLATINUM
440 bool "Apple \"platinum\" display support"
Olaf Heringa04b61d2006-07-30 03:03:52 -0700441 depends on (FB = y) && PPC_PMAC && PPC32
Linus Torvalds1da177e2005-04-16 15:20:36 -0700442 select FB_CFB_FILLRECT
443 select FB_CFB_COPYAREA
444 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700445 select FB_MACMODES
446 help
447 This driver supports a frame buffer for the "platinum" graphics
448 adapter in some Power Macintoshes.
449
450config FB_VALKYRIE
451 bool "Apple \"valkyrie\" display support"
Olaf Heringa04b61d2006-07-30 03:03:52 -0700452 depends on (FB = y) && (MAC || (PPC_PMAC && PPC32))
Linus Torvalds1da177e2005-04-16 15:20:36 -0700453 select FB_CFB_FILLRECT
454 select FB_CFB_COPYAREA
455 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700456 select FB_MACMODES
457 help
458 This driver supports a frame buffer for the "valkyrie" graphics
459 adapter in some Power Macintoshes.
460
461config FB_CT65550
462 bool "Chips 65550 display support"
Olaf Heringa04b61d2006-07-30 03:03:52 -0700463 depends on (FB = y) && PPC32
Linus Torvalds1da177e2005-04-16 15:20:36 -0700464 select FB_CFB_FILLRECT
465 select FB_CFB_COPYAREA
466 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700467 help
468 This is the frame buffer device driver for the Chips & Technologies
469 65550 graphics chip in PowerBooks.
470
471config FB_ASILIANT
Randy.Dunlape65c0852005-11-07 01:00:28 -0800472 bool "Asiliant (Chips) 69000 display support"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700473 depends on (FB = y) && PCI
474 select FB_CFB_FILLRECT
475 select FB_CFB_COPYAREA
476 select FB_CFB_IMAGEBLIT
Antonino A. Daplas4de0b1e2006-04-27 18:40:47 -0700477 help
478 This is the frame buffer device driver for the Asiliant 69030 chipset
Linus Torvalds1da177e2005-04-16 15:20:36 -0700479
480config FB_IMSTT
481 bool "IMS Twin Turbo display support"
482 depends on (FB = y) && PCI
483 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700484 select FB_MACMODES if PPC
485 help
486 The IMS Twin Turbo is a PCI-based frame buffer card bundled with
487 many Macintosh and compatible computers.
488
Linus Torvalds1da177e2005-04-16 15:20:36 -0700489config FB_VGA16
490 tristate "VGA 16-color graphics support"
491 depends on FB && (X86 || PPC)
492 select FB_CFB_FILLRECT
493 select FB_CFB_COPYAREA
494 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700495 help
496 This is the frame buffer device driver for VGA 16 color graphic
497 cards. Say Y if you have such a card.
498
499 To compile this driver as a module, choose M here: the
500 module will be called vga16fb.
501
502config FB_STI
503 tristate "HP STI frame buffer device support"
504 depends on FB && PARISC
505 select FB_CFB_FILLRECT
506 select FB_CFB_COPYAREA
507 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700508 default y
509 ---help---
510 STI refers to the HP "Standard Text Interface" which is a set of
511 BIOS routines contained in a ROM chip in HP PA-RISC based machines.
512 Enabling this option will implement the linux framebuffer device
513 using calls to the STI BIOS routines for initialisation.
514
515 If you enable this option, you will get a planar framebuffer device
516 /dev/fb which will work on the most common HP graphic cards of the
517 NGLE family, including the artist chips (in the 7xx and Bxxx series),
518 HCRX, HCRX24, CRX, CRX24 and VisEG series.
519
520 It is safe to enable this option, so you should probably say "Y".
521
522config FB_MAC
523 bool "Generic Macintosh display support"
524 depends on (FB = y) && MAC
525 select FB_CFB_FILLRECT
526 select FB_CFB_COPYAREA
527 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700528 select FB_MACMODES
529
530# bool ' Apple DAFB display support' CONFIG_FB_DAFB
531config FB_HP300
532 bool
533 depends on (FB = y) && HP300
534 select FB_CFB_FILLRECT
535 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700536 default y
537
538config FB_TGA
539 tristate "TGA framebuffer support"
540 depends on FB && ALPHA
541 select FB_CFB_FILLRECT
542 select FB_CFB_COPYAREA
543 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700544 help
545 This is the frame buffer device driver for generic TGA graphic
546 cards. Say Y if you have one of those.
547
548config FB_VESA
549 bool "VESA VGA graphics support"
Brian Gerst0d078f62005-10-30 14:59:20 -0800550 depends on (FB = y) && X86
Linus Torvalds1da177e2005-04-16 15:20:36 -0700551 select FB_CFB_FILLRECT
552 select FB_CFB_COPYAREA
553 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700554 help
555 This is the frame buffer device driver for generic VESA 2.0
556 compliant graphic cards. The older VESA 1.2 cards are not supported.
557 You will get a boot time penguin logo at no additional cost. Please
558 read <file:Documentation/fb/vesafb.txt>. If unsure, say Y.
559
Edgar Hucek90b4f9a2006-06-26 00:26:59 -0700560config FB_IMAC
561 bool "Intel-based Macintosh Framebuffer Support"
Edgar Hucekb64ef8a2006-08-13 23:24:16 -0700562 depends on (FB = y) && X86 && EFI
Edgar Hucek90b4f9a2006-06-26 00:26:59 -0700563 select FB_CFB_FILLRECT
564 select FB_CFB_COPYAREA
565 select FB_CFB_IMAGEBLIT
566 help
567 This is the frame buffer device driver for the Intel-based Macintosh
568
Linus Torvalds1da177e2005-04-16 15:20:36 -0700569config FB_HGA
570 tristate "Hercules mono graphics support"
571 depends on FB && X86
572 select FB_CFB_FILLRECT
573 select FB_CFB_COPYAREA
574 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700575 help
576 Say Y here if you have a Hercules mono graphics card.
577
578 To compile this driver as a module, choose M here: the
579 module will be called hgafb.
580
581 As this card technology is 15 years old, most people will answer N
582 here.
583
584config FB_HGA_ACCEL
585 bool "Hercules mono Acceleration functions (EXPERIMENTAL)"
586 depends on FB_HGA && EXPERIMENTAL
587 ---help---
588 This will compile the Hercules mono graphics with
589 acceleration functions.
590
Linus Torvalds1da177e2005-04-16 15:20:36 -0700591config FB_SGIVW
592 tristate "SGI Visual Workstation framebuffer support"
593 depends on FB && X86_VISWS
594 select FB_CFB_FILLRECT
595 select FB_CFB_COPYAREA
596 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700597 help
598 SGI Visual Workstation support for framebuffer graphics.
599
600config FB_GBE
601 bool "SGI Graphics Backend frame buffer support"
602 depends on (FB = y) && (SGI_IP32 || X86_VISWS)
603 select FB_CFB_FILLRECT
604 select FB_CFB_COPYAREA
605 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700606 help
607 This is the frame buffer device driver for SGI Graphics Backend.
608 This chip is used in SGI O2 and Visual Workstation 320/540.
609
610config FB_GBE_MEM
611 int "Video memory size in MB"
612 depends on FB_GBE
Martin Michlmayr80c410d2006-02-24 13:04:16 -0800613 default 4
Linus Torvalds1da177e2005-04-16 15:20:36 -0700614 help
615 This is the amount of memory reserved for the framebuffer,
616 which can be any value between 1MB and 8MB.
617
Linus Torvalds1da177e2005-04-16 15:20:36 -0700618config FB_SUN3
619 bool "Sun3 framebuffer support"
620 depends on (FB = y) && (SUN3 || SUN3X) && BROKEN
621
Mark Fortescue1a571982005-11-29 19:34:44 -0800622config FB_SBUS
623 bool "SBUS and UPA framebuffers"
Adrian Bunk0b57ee92005-12-22 21:03:47 -0800624 depends on (FB = y) && SPARC
Mark Fortescue1a571982005-11-29 19:34:44 -0800625 help
626 Say Y if you want support for SBUS or UPA based frame buffer device.
627
Linus Torvalds1da177e2005-04-16 15:20:36 -0700628config FB_BW2
629 bool "BWtwo support"
Adrian Bunk0b57ee92005-12-22 21:03:47 -0800630 depends on (FB = y) && (SPARC && FB_SBUS || (SUN3 || SUN3X) && FB_SUN3)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700631 select FB_CFB_FILLRECT
632 select FB_CFB_COPYAREA
633 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700634 help
635 This is the frame buffer device driver for the BWtwo frame buffer.
636
637config FB_CG3
638 bool "CGthree support"
Adrian Bunk0b57ee92005-12-22 21:03:47 -0800639 depends on (FB = y) && (SPARC && FB_SBUS || (SUN3 || SUN3X) && FB_SUN3)
Mark Fortescue1a571982005-11-29 19:34:44 -0800640 select FB_CFB_FILLRECT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700641 select FB_CFB_COPYAREA
642 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700643 help
644 This is the frame buffer device driver for the CGthree frame buffer.
645
646config FB_CG6
647 bool "CGsix (GX,TurboGX) support"
Adrian Bunk0b57ee92005-12-22 21:03:47 -0800648 depends on (FB = y) && (SPARC && FB_SBUS || (SUN3 || SUN3X) && FB_SUN3)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700649 select FB_CFB_COPYAREA
650 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700651 help
652 This is the frame buffer device driver for the CGsix (GX, TurboGX)
653 frame buffer.
654
655config FB_PVR2
656 tristate "NEC PowerVR 2 display support"
657 depends on FB && SH_DREAMCAST
658 select FB_CFB_FILLRECT
659 select FB_CFB_COPYAREA
660 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700661 ---help---
662 Say Y here if you have a PowerVR 2 card in your box. If you plan to
663 run linux on your Dreamcast, you will have to say Y here.
664 This driver may or may not work on other PowerVR 2 cards, but is
665 totally untested. Use at your own risk. If unsure, say N.
666
667 To compile this driver as a module, choose M here: the
668 module will be called pvr2fb.
669
670 You can pass several parameters to the driver at boot time or at
671 module load time. The parameters look like "video=pvr2:XXX", where
672 the meaning of XXX can be found at the end of the main source file
673 (<file:drivers/video/pvr2fb.c>). Please see the file
674 <file:Documentation/fb/pvr2fb.txt>.
675
676config FB_EPSON1355
677 bool "Epson 1355 framebuffer support"
678 depends on (FB = y) && (SUPERH || ARCH_CEIVA)
679 select FB_CFB_FILLRECT
680 select FB_CFB_COPYAREA
681 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700682 help
683 Build in support for the SED1355 Epson Research Embedded RAMDAC
684 LCD/CRT Controller (since redesignated as the S1D13505) as a
685 framebuffer. Product specs at
686 <http://www.erd.epson.com/vdc/html/products.htm>.
687
Randy Dunlapecc41d52005-11-07 01:00:29 -0800688config FB_S1D13XXX
689 tristate "Epson S1D13XXX framebuffer support"
690 depends on FB
691 select FB_CFB_FILLRECT
692 select FB_CFB_COPYAREA
693 select FB_CFB_IMAGEBLIT
Randy Dunlapecc41d52005-11-07 01:00:29 -0800694 help
695 Support for S1D13XXX framebuffer device family (currently only
696 working with S1D13806). Product specs at
697 <http://www.erd.epson.com/vdc/html/legacy_13xxx.htm>
698
Linus Torvalds1da177e2005-04-16 15:20:36 -0700699config FB_NVIDIA
700 tristate "nVidia Framebuffer Support"
701 depends on FB && PCI
702 select I2C_ALGOBIT if FB_NVIDIA_I2C
703 select I2C if FB_NVIDIA_I2C
Antonino A. Daplas346bc212006-10-03 01:14:43 -0700704 select FB_DDC if FB_NVIDIA_I2C
Linus Torvalds1da177e2005-04-16 15:20:36 -0700705 select FB_MODE_HELPERS
706 select FB_CFB_FILLRECT
707 select FB_CFB_COPYAREA
708 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700709 help
710 This driver supports graphics boards with the nVidia chips, TNT
711 and newer. For very old chipsets, such as the RIVA128, then use
712 the rivafb.
713 Say Y if you have such a graphics board.
714
715 To compile this driver as a module, choose M here: the
716 module will be called nvidiafb.
717
718config FB_NVIDIA_I2C
719 bool "Enable DDC Support"
Benjamin Herrenschmidt85f15032005-11-07 01:00:30 -0800720 depends on FB_NVIDIA
Linus Torvalds1da177e2005-04-16 15:20:36 -0700721 help
722 This enables I2C support for nVidia Chipsets. This is used
723 only for getting EDID information from the attached display
724 allowing for robust video mode handling and switching.
725
726 Because fbdev-2.6 requires that drivers must be able to
727 independently validate video mode parameters, you should say Y
728 here.
729
Michael Hanselmann5474c122006-06-25 05:47:08 -0700730config FB_NVIDIA_BACKLIGHT
731 bool "Support for backlight control"
Michael Hanselmann4b755992006-07-30 03:04:19 -0700732 depends on FB_NVIDIA && PMAC_BACKLIGHT
Michael Hanselmann5474c122006-06-25 05:47:08 -0700733 select FB_BACKLIGHT
Michael Hanselmann5474c122006-06-25 05:47:08 -0700734 default y
735 help
736 Say Y here if you want to control the backlight of your display.
737
Linus Torvalds1da177e2005-04-16 15:20:36 -0700738config FB_RIVA
739 tristate "nVidia Riva support"
740 depends on FB && PCI
741 select I2C_ALGOBIT if FB_RIVA_I2C
742 select I2C if FB_RIVA_I2C
Antonino A. Daplasbf5df0a2006-10-03 01:14:44 -0700743 select FB_DDC if FB_RIVA_I2C
Linus Torvalds1da177e2005-04-16 15:20:36 -0700744 select FB_MODE_HELPERS
745 select FB_CFB_FILLRECT
746 select FB_CFB_COPYAREA
747 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700748 help
749 This driver supports graphics boards with the nVidia Riva/Geforce
750 chips.
751 Say Y if you have such a graphics board.
752
753 To compile this driver as a module, choose M here: the
754 module will be called rivafb.
755
756config FB_RIVA_I2C
757 bool "Enable DDC Support"
758 depends on FB_RIVA
759 help
760 This enables I2C support for nVidia Chipsets. This is used
761 only for getting EDID information from the attached display
762 allowing for robust video mode handling and switching.
763
764 Because fbdev-2.6 requires that drivers must be able to
765 independently validate video mode parameters, you should say Y
766 here.
767
768config FB_RIVA_DEBUG
769 bool "Lots of debug output from Riva(nVidia) driver"
770 depends on FB_RIVA
771 default n
772 help
773 Say Y here if you want the Riva driver to output all sorts
774 of debugging informations to provide to the maintainer when
775 something goes wrong.
776
Michael Hanselmann5474c122006-06-25 05:47:08 -0700777config FB_RIVA_BACKLIGHT
778 bool "Support for backlight control"
Michael Hanselmann4b755992006-07-30 03:04:19 -0700779 depends on FB_RIVA && PMAC_BACKLIGHT
Michael Hanselmann5474c122006-06-25 05:47:08 -0700780 select FB_BACKLIGHT
Michael Hanselmann5474c122006-06-25 05:47:08 -0700781 default y
782 help
783 Say Y here if you want to control the backlight of your display.
784
Linus Torvalds1da177e2005-04-16 15:20:36 -0700785config FB_I810
786 tristate "Intel 810/815 support (EXPERIMENTAL)"
Brian Gerst0d078f62005-10-30 14:59:20 -0800787 depends on FB && EXPERIMENTAL && PCI && X86_32
Linus Torvalds1da177e2005-04-16 15:20:36 -0700788 select AGP
789 select AGP_INTEL
790 select FB_MODE_HELPERS
791 select FB_CFB_FILLRECT
792 select FB_CFB_COPYAREA
793 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700794 help
795 This driver supports the on-board graphics built in to the Intel 810
796 and 815 chipsets. Say Y if you have and plan to use such a board.
797
798 To compile this driver as a module, choose M here: the
799 module will be called i810fb.
800
801 For more information, please read
802 <file:Documentation/fb/intel810.txt>
803
804config FB_I810_GTF
805 bool "use VESA Generalized Timing Formula"
806 depends on FB_I810
807 help
808 If you say Y, then the VESA standard, Generalized Timing Formula
809 or GTF, will be used to calculate the required video timing values
810 per video mode. Since the GTF allows nondiscrete timings
811 (nondiscrete being a range of values as opposed to discrete being a
812 set of values), you'll be able to use any combination of horizontal
813 and vertical resolutions, and vertical refresh rates without having
814 to specify your own timing parameters. This is especially useful
815 to maximize the performance of an aging display, or if you just
816 have a display with nonstandard dimensions. A VESA compliant
817 monitor is recommended, but can still work with non-compliant ones.
818 If you need or want this, then select this option. The timings may
819 not be compliant with Intel's recommended values. Use at your own
820 risk.
821
822 If you say N, the driver will revert to discrete video timings
823 using a set recommended by Intel in their documentation.
824
825 If unsure, say N.
826
Antonino A. Daplas74f6ae82005-09-09 13:10:04 -0700827config FB_I810_I2C
828 bool "Enable DDC Support"
Antonino A. Daplasdb845022005-09-13 01:25:02 -0700829 depends on FB_I810 && FB_I810_GTF
830 select I2C
Antonino A. Daplas74f6ae82005-09-09 13:10:04 -0700831 select I2C_ALGOBIT
Antonino A. Daplase80987f2006-10-03 01:14:44 -0700832 select FB_DDC
Antonino A. Daplas74f6ae82005-09-09 13:10:04 -0700833 help
834
Linus Torvalds1da177e2005-04-16 15:20:36 -0700835config FB_INTEL
Christian Merkled463d342006-08-22 10:07:01 +1000836 tristate "Intel 830M/845G/852GM/855GM/865G/915G/945G support (EXPERIMENTAL)"
Dave Airlie0c187ad2006-03-23 11:20:08 +1100837 depends on FB && EXPERIMENTAL && PCI && X86
Linus Torvalds1da177e2005-04-16 15:20:36 -0700838 select AGP
839 select AGP_INTEL
Dennis Munsie1f6e8442006-06-20 14:55:55 -0400840 select I2C_ALGOBIT if FB_INTEL_I2C
841 select I2C if FB_INTEL_I2C
Linus Torvalds1da177e2005-04-16 15:20:36 -0700842 select FB_MODE_HELPERS
843 select FB_CFB_FILLRECT
844 select FB_CFB_COPYAREA
845 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700846 help
847 This driver supports the on-board graphics built in to the Intel
Christian Merkled463d342006-08-22 10:07:01 +1000848 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM chipsets.
Linus Torvalds1da177e2005-04-16 15:20:36 -0700849 Say Y if you have and plan to use such a board.
850
Dennis Munsie1f6e8442006-06-20 14:55:55 -0400851 If you say Y here and want DDC/I2C support you must first say Y to
852 "I2C support" and "I2C bit-banging support" in the character devices
853 section.
854
855 If you say M here then "I2C support" and "I2C bit-banging support"
856 can be build either as modules or built-in.
857
858 To compile this driver as a module, choose M here: the
Linus Torvalds1da177e2005-04-16 15:20:36 -0700859 module will be called intelfb.
860
Christian Merkled463d342006-08-22 10:07:01 +1000861 For more information, please read <file:Documentation/fb/intelfb.txt>
862
Linus Torvalds1da177e2005-04-16 15:20:36 -0700863config FB_INTEL_DEBUG
Dennis Munsie1f6e8442006-06-20 14:55:55 -0400864 bool "Intel driver Debug Messages"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700865 depends on FB_INTEL
866 ---help---
867 Say Y here if you want the Intel driver to output all sorts
868 of debugging informations to provide to the maintainer when
869 something goes wrong.
870
Dennis Munsie1f6e8442006-06-20 14:55:55 -0400871config FB_INTEL_I2C
872 bool "DDC/I2C for Intel framebuffer support"
873 depends on FB_INTEL
874 default y
875 help
876 Say Y here if you want DDC/I2C support for your on-board Intel graphics.
877
Linus Torvalds1da177e2005-04-16 15:20:36 -0700878config FB_MATROX
879 tristate "Matrox acceleration"
880 depends on FB && PCI
881 select FB_CFB_FILLRECT
882 select FB_CFB_COPYAREA
883 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700884 select FB_TILEBLITTING
885 select FB_MACMODES if PPC_PMAC
886 ---help---
887 Say Y here if you have a Matrox Millennium, Matrox Millennium II,
888 Matrox Mystique, Matrox Mystique 220, Matrox Productiva G100, Matrox
889 Mystique G200, Matrox Millennium G200, Matrox Marvel G200 video,
890 Matrox G400, G450 or G550 card in your box.
891
892 To compile this driver as a module, choose M here: the
893 module will be called matroxfb.
894
895 You can pass several parameters to the driver at boot time or at
896 module load time. The parameters look like "video=matrox:XXX", and
897 are described in <file:Documentation/fb/matroxfb.txt>.
898
899config FB_MATROX_MILLENIUM
900 bool "Millennium I/II support"
901 depends on FB_MATROX
902 help
903 Say Y here if you have a Matrox Millennium or Matrox Millennium II
904 video card. If you select "Advanced lowlevel driver options" below,
905 you should check 4 bpp packed pixel, 8 bpp packed pixel, 16 bpp
906 packed pixel, 24 bpp packed pixel and 32 bpp packed pixel. You can
907 also use font widths different from 8.
908
909config FB_MATROX_MYSTIQUE
910 bool "Mystique support"
911 depends on FB_MATROX
912 help
913 Say Y here if you have a Matrox Mystique or Matrox Mystique 220
914 video card. If you select "Advanced lowlevel driver options" below,
915 you should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp
916 packed pixel and 32 bpp packed pixel. You can also use font widths
917 different from 8.
918
919config FB_MATROX_G
920 bool "G100/G200/G400/G450/G550 support"
921 depends on FB_MATROX
922 ---help---
923 Say Y here if you have a Matrox G100, G200, G400, G450 or G550 based
924 video card. If you select "Advanced lowlevel driver options", you
925 should check 8 bpp packed pixel, 16 bpp packed pixel, 24 bpp packed
926 pixel and 32 bpp packed pixel. You can also use font widths
927 different from 8.
928
929 If you need support for G400 secondary head, you must first say Y to
930 "I2C support" in the character devices section, and then to
931 "Matrox I2C support" and "G400 second head support" here in the
932 framebuffer section. G450/G550 secondary head and digital output
933 are supported without additional modules.
934
935 The driver starts in monitor mode. You must use the matroxset tool
936 (available at <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to
937 swap primary and secondary head outputs, or to change output mode.
938 Secondary head driver always start in 640x480 resolution and you
939 must use fbset to change it.
940
941 Do not forget that second head supports only 16 and 32 bpp
942 packed pixels, so it is a good idea to compile them into the kernel
943 too. You can use only some font widths, as the driver uses generic
944 painting procedures (the secondary head does not use acceleration
945 engine).
946
947 G450/G550 hardware can display TV picture only from secondary CRTC,
948 and it performs no scaling, so picture must have 525 or 625 lines.
949
950config FB_MATROX_I2C
951 tristate "Matrox I2C support"
952 depends on FB_MATROX && I2C
953 select I2C_ALGOBIT
954 ---help---
955 This drivers creates I2C buses which are needed for accessing the
956 DDC (I2C) bus present on all Matroxes, an I2C bus which
957 interconnects Matrox optional devices, like MGA-TVO on G200 and
958 G400, and the secondary head DDC bus, present on G400 only.
959
960 You can say Y or M here if you want to experiment with monitor
961 detection code. You must say Y or M here if you want to use either
962 second head of G400 or MGA-TVO on G200 or G400.
963
964 If you compile it as module, it will create a module named
965 i2c-matroxfb.
966
967config FB_MATROX_MAVEN
968 tristate "G400 second head support"
969 depends on FB_MATROX_G && FB_MATROX_I2C
970 ---help---
971 WARNING !!! This support does not work with G450 !!!
972
973 Say Y or M here if you want to use a secondary head (meaning two
974 monitors in parallel) on G400 or MGA-TVO add-on on G200. Secondary
975 head is not compatible with accelerated XFree 3.3.x SVGA servers -
976 secondary head output is blanked while you are in X. With XFree
977 3.9.17 preview you can use both heads if you use SVGA over fbdev or
978 the fbdev driver on first head and the fbdev driver on second head.
979
980 If you compile it as module, two modules are created,
981 matroxfb_crtc2 and matroxfb_maven. Matroxfb_maven is needed for
982 both G200 and G400, matroxfb_crtc2 is needed only by G400. You must
983 also load i2c-matroxfb to get it to run.
984
985 The driver starts in monitor mode and you must use the matroxset
986 tool (available at
987 <ftp://platan.vc.cvut.cz/pub/linux/matrox-latest/>) to switch it to
988 PAL or NTSC or to swap primary and secondary head outputs.
989 Secondary head driver also always start in 640x480 resolution, you
990 must use fbset to change it.
991
992 Also do not forget that second head supports only 16 and 32 bpp
993 packed pixels, so it is a good idea to compile them into the kernel
994 too. You can use only some font widths, as the driver uses generic
995 painting procedures (the secondary head does not use acceleration
996 engine).
997
998config FB_MATROX_MULTIHEAD
999 bool "Multihead support"
1000 depends on FB_MATROX
1001 ---help---
1002 Say Y here if you have more than one (supported) Matrox device in
1003 your computer and you want to use all of them for different monitors
1004 ("multihead"). If you have only one device, you should say N because
1005 the driver compiled with Y is larger and a bit slower, especially on
1006 ia32 (ix86).
1007
1008 If you said M to "Matrox unified accelerated driver" and N here, you
1009 will still be able to use several Matrox devices simultaneously:
1010 insert several instances of the module matroxfb into the kernel
1011 with insmod, supplying the parameter "dev=N" where N is 0, 1, etc.
1012 for the different Matrox devices. This method is slightly faster but
1013 uses 40 KB of kernel memory per Matrox card.
1014
1015 There is no need for enabling 'Matrox multihead support' if you have
1016 only one Matrox card in the box.
1017
Linus Torvalds1da177e2005-04-16 15:20:36 -07001018config FB_RADEON
1019 tristate "ATI Radeon display support"
1020 depends on FB && PCI
1021 select I2C_ALGOBIT if FB_RADEON_I2C
1022 select I2C if FB_RADEON_I2C
Dennis Munsie7a450932006-10-03 01:14:46 -07001023 select FB_DDC if FB_RADEON_I2C
Linus Torvalds1da177e2005-04-16 15:20:36 -07001024 select FB_MODE_HELPERS
1025 select FB_CFB_FILLRECT
1026 select FB_CFB_COPYAREA
1027 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001028 select FB_MACMODES if PPC_OF
1029 help
1030 Choose this option if you want to use an ATI Radeon graphics card as
1031 a framebuffer device. There are both PCI and AGP versions. You
1032 don't need to choose this to run the Radeon in plain VGA mode.
1033
1034 If you say Y here and want DDC/I2C support you must first say Y to
1035 "I2C support" and "I2C bit-banging support" in the character devices
1036 section.
1037
1038 If you say M here then "I2C support" and "I2C bit-banging support"
1039 can be build either as modules or built-in.
1040
1041 There is a product page at
Antonino A. Daplasf510a3c2005-09-09 13:04:41 -07001042 http://apps.ati.com/ATIcompare/
Michael Hanselmann5474c122006-06-25 05:47:08 -07001043
Linus Torvalds1da177e2005-04-16 15:20:36 -07001044config FB_RADEON_I2C
1045 bool "DDC/I2C for ATI Radeon support"
1046 depends on FB_RADEON
1047 default y
1048 help
1049 Say Y here if you want DDC/I2C support for your Radeon board.
1050
Michael Hanselmann5474c122006-06-25 05:47:08 -07001051config FB_RADEON_BACKLIGHT
1052 bool "Support for backlight control"
Michael Hanselmann4b755992006-07-30 03:04:19 -07001053 depends on FB_RADEON && PMAC_BACKLIGHT
Michael Hanselmann5474c122006-06-25 05:47:08 -07001054 select FB_BACKLIGHT
Michael Hanselmann5474c122006-06-25 05:47:08 -07001055 default y
1056 help
1057 Say Y here if you want to control the backlight of your display.
1058
Linus Torvalds1da177e2005-04-16 15:20:36 -07001059config FB_RADEON_DEBUG
1060 bool "Lots of debug output from Radeon driver"
1061 depends on FB_RADEON
1062 default n
1063 help
1064 Say Y here if you want the Radeon driver to output all sorts
1065 of debugging informations to provide to the maintainer when
1066 something goes wrong.
1067
1068config FB_ATY128
1069 tristate "ATI Rage128 display support"
1070 depends on FB && PCI
1071 select FB_CFB_FILLRECT
1072 select FB_CFB_COPYAREA
1073 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001074 select FB_MACMODES if PPC_PMAC
1075 help
1076 This driver supports graphics boards with the ATI Rage128 chips.
1077 Say Y if you have such a graphics board and read
1078 <file:Documentation/fb/aty128fb.txt>.
1079
1080 To compile this driver as a module, choose M here: the
1081 module will be called aty128fb.
1082
Michael Hanselmann5474c122006-06-25 05:47:08 -07001083config FB_ATY128_BACKLIGHT
1084 bool "Support for backlight control"
Michael Hanselmann4b755992006-07-30 03:04:19 -07001085 depends on FB_ATY128 && PMAC_BACKLIGHT
Michael Hanselmann5474c122006-06-25 05:47:08 -07001086 select FB_BACKLIGHT
Michael Hanselmann5474c122006-06-25 05:47:08 -07001087 default y
1088 help
1089 Say Y here if you want to control the backlight of your display.
1090
Linus Torvalds1da177e2005-04-16 15:20:36 -07001091config FB_ATY
1092 tristate "ATI Mach64 display support" if PCI || ATARI
Andrew Mortonf2e782e2006-04-10 22:55:45 -07001093 depends on FB && !SPARC32
Linus Torvalds1da177e2005-04-16 15:20:36 -07001094 select FB_CFB_FILLRECT
1095 select FB_CFB_COPYAREA
1096 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001097 select FB_MACMODES if PPC
1098 help
1099 This driver supports graphics boards with the ATI Mach64 chips.
1100 Say Y if you have such a graphics board.
1101
1102 To compile this driver as a module, choose M here: the
1103 module will be called atyfb.
1104
1105config FB_ATY_CT
1106 bool "Mach64 CT/VT/GT/LT (incl. 3D RAGE) support"
1107 depends on PCI && FB_ATY
1108 default y if SPARC64 && FB_PCI
1109 help
1110 Say Y here to support use of ATI's 64-bit Rage boards (or other
1111 boards based on the Mach64 CT, VT, GT, and LT chipsets) as a
1112 framebuffer device. The ATI product support page for these boards
1113 is at <http://support.ati.com/products/pc/mach64/>.
1114
1115config FB_ATY_GENERIC_LCD
1116 bool "Mach64 generic LCD support (EXPERIMENTAL)"
1117 depends on FB_ATY_CT
1118 help
1119 Say Y if you have a laptop with an ATI Rage LT PRO, Rage Mobility,
1120 Rage XC, or Rage XL chipset.
1121
Linus Torvalds1da177e2005-04-16 15:20:36 -07001122config FB_ATY_GX
1123 bool "Mach64 GX support" if PCI
1124 depends on FB_ATY
1125 default y if ATARI
1126 help
1127 Say Y here to support use of the ATI Mach64 Graphics Expression
1128 board (or other boards based on the Mach64 GX chipset) as a
1129 framebuffer device. The ATI product support page for these boards
1130 is at
1131 <http://support.ati.com/products/pc/mach64/graphics_xpression.html>.
1132
Michael Hanselmann5474c122006-06-25 05:47:08 -07001133config FB_ATY_BACKLIGHT
1134 bool "Support for backlight control"
Michael Hanselmann4b755992006-07-30 03:04:19 -07001135 depends on FB_ATY && PMAC_BACKLIGHT
Michael Hanselmann5474c122006-06-25 05:47:08 -07001136 select FB_BACKLIGHT
Michael Hanselmann5474c122006-06-25 05:47:08 -07001137 default y
1138 help
1139 Say Y here if you want to control the backlight of your display.
1140
Randy.Dunlape65c0852005-11-07 01:00:28 -08001141config FB_S3TRIO
1142 bool "S3 Trio display support"
1143 depends on (FB = y) && PPC && BROKEN
1144 help
1145 If you have a S3 Trio say Y. Say N for S3 Virge.
1146
Linus Torvalds1da177e2005-04-16 15:20:36 -07001147config FB_SAVAGE
1148 tristate "S3 Savage support"
1149 depends on FB && PCI && EXPERIMENTAL
1150 select I2C_ALGOBIT if FB_SAVAGE_I2C
1151 select I2C if FB_SAVAGE_I2C
Antonino A. Daplas946c4ea2006-10-03 01:14:45 -07001152 select FB_DDC if FB_SAVAGE_I2C
Linus Torvalds1da177e2005-04-16 15:20:36 -07001153 select FB_MODE_HELPERS
1154 select FB_CFB_FILLRECT
1155 select FB_CFB_COPYAREA
1156 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001157 help
1158 This driver supports notebooks and computers with S3 Savage PCI/AGP
1159 chips.
1160
1161 Say Y if you have such a graphics card.
1162
1163 To compile this driver as a module, choose M here; the module
1164 will be called savagefb.
1165
1166config FB_SAVAGE_I2C
1167 bool "Enable DDC2 Support"
1168 depends on FB_SAVAGE
1169 help
1170 This enables I2C support for S3 Savage Chipsets. This is used
1171 only for getting EDID information from the attached display
1172 allowing for robust video mode handling and switching.
1173
1174 Because fbdev-2.6 requires that drivers must be able to
1175 independently validate video mode parameters, you should say Y
1176 here.
1177
1178config FB_SAVAGE_ACCEL
1179 bool "Enable Console Acceleration"
1180 depends on FB_SAVAGE
1181 default n
1182 help
1183 This option will compile in console acceleration support. If
1184 the resulting framebuffer console has bothersome glitches, then
1185 choose N here.
1186
1187config FB_SIS
Thomas Winischhofer544393f2005-09-09 13:04:45 -07001188 tristate "SiS/XGI display support"
Linus Torvalds1da177e2005-04-16 15:20:36 -07001189 depends on FB && PCI
1190 select FB_CFB_FILLRECT
1191 select FB_CFB_COPYAREA
1192 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001193 help
Thomas Winischhofer544393f2005-09-09 13:04:45 -07001194 This is the frame buffer device driver for the SiS 300, 315, 330
1195 and 340 series as well as XGI V3XT, V5, V8, Z7 graphics chipsets.
1196 Specs available at <http://www.sis.com> and <http://www.xgitech.com>.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001197
1198 To compile this driver as a module, choose M here; the module
1199 will be called sisfb.
1200
1201config FB_SIS_300
1202 bool "SiS 300 series support"
1203 depends on FB_SIS
1204 help
1205 Say Y here to support use of the SiS 300/305, 540, 630 and 730.
1206
1207config FB_SIS_315
Thomas Winischhofer544393f2005-09-09 13:04:45 -07001208 bool "SiS 315/330/340 series and XGI support"
Linus Torvalds1da177e2005-04-16 15:20:36 -07001209 depends on FB_SIS
1210 help
Thomas Winischhofer544393f2005-09-09 13:04:45 -07001211 Say Y here to support use of the SiS 315, 330 and 340 series
1212 (315/H/PRO, 55x, 650, 651, 740, 330, 661, 741, 760, 761) as well
1213 as XGI V3XT, V5, V8 and Z7.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001214
1215config FB_NEOMAGIC
1216 tristate "NeoMagic display support"
1217 depends on FB && PCI
1218 select FB_MODE_HELPERS
1219 select FB_CFB_FILLRECT
1220 select FB_CFB_COPYAREA
1221 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001222 help
1223 This driver supports notebooks with NeoMagic PCI chips.
1224 Say Y if you have such a graphics card.
1225
1226 To compile this driver as a module, choose M here: the
1227 module will be called neofb.
1228
1229config FB_KYRO
1230 tristate "IMG Kyro support"
1231 depends on FB && PCI
1232 select FB_CFB_FILLRECT
1233 select FB_CFB_COPYAREA
1234 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001235 help
1236 Say Y here if you have a STG4000 / Kyro / PowerVR 3 based
1237 graphics board.
1238
1239 To compile this driver as a module, choose M here: the
1240 module will be called kyrofb.
1241
1242config FB_3DFX
1243 tristate "3Dfx Banshee/Voodoo3 display support"
1244 depends on FB && PCI
1245 select FB_CFB_IMAGEBLIT
1246 select FB_CFB_FILLRECT
1247 select FB_CFB_COPYAREA
Linus Torvalds1da177e2005-04-16 15:20:36 -07001248 help
1249 This driver supports graphics boards with the 3Dfx Banshee/Voodoo3
1250 chips. Say Y if you have such a graphics board.
1251
1252 To compile this driver as a module, choose M here: the
1253 module will be called tdfxfb.
1254
1255config FB_3DFX_ACCEL
1256 bool "3Dfx Banshee/Voodoo3 Acceleration functions (EXPERIMENTAL)"
1257 depends on FB_3DFX && EXPERIMENTAL
1258 ---help---
1259 This will compile the 3Dfx Banshee/Voodoo3 frame buffer device
1260 with acceleration functions.
1261
1262
1263config FB_VOODOO1
1264 tristate "3Dfx Voodoo Graphics (sst1) support"
1265 depends on FB && PCI
1266 select FB_CFB_FILLRECT
1267 select FB_CFB_COPYAREA
1268 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001269 ---help---
1270 Say Y here if you have a 3Dfx Voodoo Graphics (Voodoo1/sst1) or
1271 Voodoo2 (cvg) based graphics card.
1272
1273 To compile this driver as a module, choose M here: the
1274 module will be called sstfb.
1275
1276 WARNING: Do not use any application that uses the 3D engine
1277 (namely glide) while using this driver.
1278 Please read the <file:Documentation/fb/README-sstfb.txt> for supported
1279 options and other important info support.
1280
Knut Petersen9fa68ea2005-09-09 13:04:56 -07001281config FB_CYBLA
1282 tristate "Cyberblade/i1 support"
Knut Petersen44637a12006-01-09 15:04:20 +01001283 depends on FB && PCI && X86_32 && !64BIT
Knut Petersen9fa68ea2005-09-09 13:04:56 -07001284 select FB_CFB_IMAGEBLIT
Knut Petersen9fa68ea2005-09-09 13:04:56 -07001285 select VIDEO_SELECT
1286 ---help---
1287 This driver is supposed to support the Trident Cyberblade/i1
1288 graphics core integrated in the VIA VT8601A North Bridge,
1289 also known as VIA Apollo PLE133.
1290
1291 Status:
1292 - Developed, tested and working on EPIA 5000 and EPIA 800.
1293 - Does work reliable on all systems with CRT/LCD connected to
1294 normal VGA ports.
1295 - Should work on systems that do use the internal LCD port, but
1296 this is absolutely not tested.
1297
1298 Character imageblit, copyarea and rectangle fill are hw accelerated,
1299 ypan scrolling is used by default.
1300
1301 Please do read <file:Documentation/fb/cyblafb/*>.
1302
1303 To compile this driver as a module, choose M here: the
1304 module will be called cyblafb.
1305
Linus Torvalds1da177e2005-04-16 15:20:36 -07001306config FB_TRIDENT
1307 tristate "Trident support"
1308 depends on FB && PCI
1309 select FB_CFB_FILLRECT
1310 select FB_CFB_COPYAREA
1311 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001312 ---help---
1313 This driver is supposed to support graphics boards with the
1314 Trident CyberXXXX/Image/CyberBlade chips mostly found in laptops
1315 but also on some motherboards. For more information, read
1316 <file:Documentation/fb/tridentfb.txt>
1317
Knut Petersen9fa68ea2005-09-09 13:04:56 -07001318 Cyberblade/i1 support will be removed soon, use the cyblafb driver
1319 instead.
1320
Linus Torvalds1da177e2005-04-16 15:20:36 -07001321 Say Y if you have such a graphics board.
1322
Knut Petersen9fa68ea2005-09-09 13:04:56 -07001323
Linus Torvalds1da177e2005-04-16 15:20:36 -07001324 To compile this driver as a module, choose M here: the
1325 module will be called tridentfb.
1326
1327config FB_TRIDENT_ACCEL
1328 bool "Trident Acceleration functions (EXPERIMENTAL)"
1329 depends on FB_TRIDENT && EXPERIMENTAL
1330 ---help---
1331 This will compile the Trident frame buffer device with
1332 acceleration functions.
1333
Linus Torvalds1da177e2005-04-16 15:20:36 -07001334config FB_PM3
1335 tristate "Permedia3 support"
1336 depends on FB && PCI && BROKEN
1337 help
1338 This is the frame buffer device driver for the 3DLabs Permedia3
1339 chipset, used in Formac ProFormance III, 3DLabs Oxygen VX1 &
1340 similar boards, 3DLabs Permedia3 Create!, Appian Jeronimo 2000
1341 and maybe other boards.
1342
Linus Torvalds1da177e2005-04-16 15:20:36 -07001343config FB_AU1100
1344 bool "Au1100 LCD Driver"
1345 depends on (FB = y) && EXPERIMENTAL && PCI && MIPS && MIPS_PB1100=y
1346
Ralf Baechlef95ec3c2006-03-27 01:17:27 -08001347config FB_AU1200
1348 bool "Au1200 LCD Driver"
1349 depends on FB && MIPS && SOC_AU1200
1350 select FB_CFB_FILLRECT
1351 select FB_CFB_COPYAREA
1352 select FB_CFB_IMAGEBLIT
1353 help
1354 This is the framebuffer driver for the AMD Au1200 SOC. It can drive
1355 various panels and CRTs by passing in kernel cmd line option
1356 au1200fb:panel=<name>.
1357
Linus Torvalds1da177e2005-04-16 15:20:36 -07001358source "drivers/video/geode/Kconfig"
1359
Linus Torvalds1da177e2005-04-16 15:20:36 -07001360config FB_FFB
1361 bool "Creator/Creator3D/Elite3D support"
1362 depends on FB_SBUS && SPARC64
1363 select FB_CFB_COPYAREA
1364 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001365 help
1366 This is the frame buffer device driver for the Creator, Creator3D,
1367 and Elite3D graphics boards.
1368
1369config FB_TCX
1370 bool "TCX (SS4/SS5 only) support"
1371 depends on FB_SBUS
1372 select FB_CFB_FILLRECT
1373 select FB_CFB_COPYAREA
1374 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001375 help
1376 This is the frame buffer device driver for the TCX 24/8bit frame
1377 buffer.
1378
1379config FB_CG14
1380 bool "CGfourteen (SX) support"
1381 depends on FB_SBUS
1382 select FB_CFB_FILLRECT
1383 select FB_CFB_COPYAREA
1384 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001385 help
1386 This is the frame buffer device driver for the CGfourteen frame
1387 buffer on Desktop SPARCsystems with the SX graphics option.
1388
1389config FB_P9100
1390 bool "P9100 (Sparcbook 3 only) support"
1391 depends on FB_SBUS
1392 select FB_CFB_FILLRECT
1393 select FB_CFB_COPYAREA
1394 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001395 help
1396 This is the frame buffer device driver for the P9100 card
1397 supported on Sparcbook 3 machines.
1398
1399config FB_LEO
1400 bool "Leo (ZX) support"
1401 depends on FB_SBUS
1402 select FB_CFB_FILLRECT
1403 select FB_CFB_COPYAREA
1404 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001405 help
1406 This is the frame buffer device driver for the SBUS-based Sun ZX
1407 (leo) frame buffer cards.
1408
1409config FB_PCI
1410 bool "PCI framebuffers"
Adrian Bunk0b57ee92005-12-22 21:03:47 -08001411 depends on (FB = y) && PCI && SPARC
Linus Torvalds1da177e2005-04-16 15:20:36 -07001412
1413config FB_IGA
1414 bool "IGA 168x display support"
1415 depends on SPARC32 && FB_PCI
1416 select FB_CFB_FILLRECT
1417 select FB_CFB_COPYAREA
1418 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001419 help
1420 This is the framebuffer device for the INTERGRAPHICS 1680 and
1421 successor frame buffer cards.
1422
1423config FB_HIT
1424 tristate "HD64461 Frame Buffer support"
1425 depends on FB && HD64461
1426 select FB_CFB_FILLRECT
1427 select FB_CFB_COPYAREA
1428 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001429 help
1430 This is the frame buffer device driver for the Hitachi HD64461 LCD
1431 frame buffer card.
1432
1433config FB_PMAG_AA
1434 bool "PMAG-AA TURBOchannel framebuffer support"
Maciej W. Rozyckia9350002005-06-13 19:50:42 +00001435 depends on (FB = y) && TC
Linus Torvalds1da177e2005-04-16 15:20:36 -07001436 select FB_CFB_FILLRECT
1437 select FB_CFB_COPYAREA
1438 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001439 help
1440 Support for the PMAG-AA TURBOchannel framebuffer card (1280x1024x1)
1441 used mainly in the MIPS-based DECstation series.
1442
1443config FB_PMAG_BA
1444 bool "PMAG-BA TURBOchannel framebuffer support"
Maciej W. Rozyckia9350002005-06-13 19:50:42 +00001445 depends on (FB = y) && TC
Linus Torvalds1da177e2005-04-16 15:20:36 -07001446 select FB_CFB_FILLRECT
1447 select FB_CFB_COPYAREA
1448 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001449 help
1450 Support for the PMAG-BA TURBOchannel framebuffer card (1024x864x8)
1451 used mainly in the MIPS-based DECstation series.
1452
1453config FB_PMAGB_B
1454 bool "PMAGB-B TURBOchannel framebuffer support"
Maciej W. Rozyckia9350002005-06-13 19:50:42 +00001455 depends on (FB = y) && TC
Linus Torvalds1da177e2005-04-16 15:20:36 -07001456 select FB_CFB_FILLRECT
1457 select FB_CFB_COPYAREA
1458 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001459 help
1460 Support for the PMAGB-B TURBOchannel framebuffer card used mainly
1461 in the MIPS-based DECstation series. The card is currently only
1462 supported in 1280x1024x8 mode.
1463
1464config FB_MAXINE
1465 bool "Maxine (Personal DECstation) onboard framebuffer support"
Maciej W. Rozyckia9350002005-06-13 19:50:42 +00001466 depends on (FB = y) && MACH_DECSTATION
Linus Torvalds1da177e2005-04-16 15:20:36 -07001467 select FB_CFB_FILLRECT
1468 select FB_CFB_COPYAREA
1469 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001470 help
1471 Support for the onboard framebuffer (1024x768x8) in the Personal
1472 DECstation series (Personal DECstation 5000/20, /25, /33, /50,
1473 Codename "Maxine").
1474
1475config FB_TX3912
1476 bool "TMPTX3912/PR31700 frame buffer support"
1477 depends on (FB = y) && NINO
1478 select FB_CFB_FILLRECT
1479 select FB_CFB_COPYAREA
1480 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001481 help
1482 The TX3912 is a Toshiba RISC processor based on the MIPS 3900 core
1483 see <http://www.toshiba.com/taec/components/Generic/risc/tx3912.htm>.
1484
1485 Say Y here to enable kernel support for the on-board framebuffer.
1486
1487config FB_G364
Yoichi Yuasab38817d2005-07-27 11:43:28 -07001488 bool "G364 frame buffer support"
1489 depends on (FB = y) && (MIPS_MAGNUM_4000 || OLIVETTI_M700)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001490 select FB_CFB_FILLRECT
1491 select FB_CFB_COPYAREA
1492 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001493 help
1494 The G364 driver is the framebuffer used in MIPS Magnum 4000 and
1495 Olivetti M700-10 systems.
1496
1497config FB_68328
1498 bool "Motorola 68328 native frame buffer support"
1499 depends on FB && (M68328 || M68EZ328 || M68VZ328)
1500 select FB_CFB_FILLRECT
1501 select FB_CFB_COPYAREA
1502 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001503 help
1504 Say Y here if you want to support the built-in frame buffer of
1505 the Motorola 68328 CPU family.
1506
1507config FB_PXA
1508 tristate "PXA LCD framebuffer support"
1509 depends on FB && ARCH_PXA
1510 select FB_CFB_FILLRECT
1511 select FB_CFB_COPYAREA
1512 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001513 ---help---
1514 Frame buffer driver for the built-in LCD controller in the Intel
1515 PXA2x0 processor.
1516
1517 This driver is also available as a module ( = code which can be
1518 inserted and removed from the running kernel whenever you want). The
YOSHIFUJI Hideaki74b4f042006-01-09 20:53:46 -08001519 module will be called pxafb. If you want to compile it as a module,
Linus Torvalds1da177e2005-04-16 15:20:36 -07001520 say M here and read <file:Documentation/modules.txt>.
1521
1522 If unsure, say N.
1523
Linus Torvalds1da177e2005-04-16 15:20:36 -07001524config FB_PXA_PARAMETERS
1525 bool "PXA LCD command line parameters"
1526 default n
1527 depends on FB_PXA
1528 ---help---
1529 Enable the use of kernel command line or module parameters
1530 to configure the physical properties of the LCD panel when
1531 using the PXA LCD driver.
1532
1533 This option allows you to override the panel parameters
1534 supplied by the platform in order to support multiple
1535 different models of flatpanel. If you will only be using a
1536 single model of flatpanel then you can safely leave this
1537 option disabled.
1538
1539 <file:Documentation/fb/pxafb.txt> describes the available parameters.
1540
Mike Rapoport22caf042006-07-14 00:24:34 -07001541config FB_MBX
1542 tristate "2700G LCD framebuffer support"
1543 depends on FB && ARCH_PXA
1544 select FB_CFB_FILLRECT
1545 select FB_CFB_COPYAREA
1546 select FB_CFB_IMAGEBLIT
1547 ---help---
1548 Framebuffer driver for the Intel 2700G (Marathon) Graphics
1549 Accelerator
1550
1551config FB_MBX_DEBUG
1552 bool "Enable debugging info via debugfs"
1553 depends on FB_MBX && DEBUG_FS
1554 default n
1555 ---help---
1556 Enable this if you want debugging information using the debug
1557 filesystem (debugfs)
1558
1559 If unsure, say N.
1560
Randy Dunlapecc41d52005-11-07 01:00:29 -08001561config FB_W100
1562 tristate "W100 frame buffer support"
1563 depends on FB && PXA_SHARPSL
1564 select FB_CFB_FILLRECT
1565 select FB_CFB_COPYAREA
1566 select FB_CFB_IMAGEBLIT
Randy Dunlapecc41d52005-11-07 01:00:29 -08001567 ---help---
1568 Frame buffer driver for the w100 as found on the Sharp SL-Cxx series.
1569
1570 This driver is also available as a module ( = code which can be
1571 inserted and removed from the running kernel whenever you want). The
YOSHIFUJI Hideaki74b4f042006-01-09 20:53:46 -08001572 module will be called w100fb. If you want to compile it as a module,
Randy Dunlapecc41d52005-11-07 01:00:29 -08001573 say M here and read <file:Documentation/modules.txt>.
1574
1575 If unsure, say N.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001576
Arnaud Patard20fd5762005-09-09 13:10:07 -07001577config FB_S3C2410
1578 tristate "S3C2410 LCD framebuffer support"
1579 depends on FB && ARCH_S3C2410
1580 select FB_CFB_FILLRECT
1581 select FB_CFB_COPYAREA
1582 select FB_CFB_IMAGEBLIT
Arnaud Patard20fd5762005-09-09 13:10:07 -07001583 ---help---
1584 Frame buffer driver for the built-in LCD controller in the Samsung
1585 S3C2410 processor.
1586
1587 This driver is also available as a module ( = code which can be
1588 inserted and removed from the running kernel whenever you want). The
1589 module will be called s3c2410fb. If you want to compile it as a module,
1590 say M here and read <file:Documentation/modules.txt>.
1591
1592 If unsure, say N.
1593config FB_S3C2410_DEBUG
1594 bool "S3C2410 lcd debug messages"
1595 depends on FB_S3C2410
1596 help
1597 Turn on debugging messages. Note that you can set/unset at run time
1598 through sysfs
1599
Vitaly Wool36c93662006-07-03 00:24:19 -07001600config FB_PNX4008_DUM
1601 tristate "Display Update Module support on Philips PNX4008 board"
1602 depends on FB && ARCH_PNX4008
1603 ---help---
1604 Say Y here to enable support for PNX4008 Display Update Module (DUM)
1605
1606config FB_PNX4008_DUM_RGB
1607 tristate "RGB Framebuffer support on Philips PNX4008 board"
1608 depends on FB_PNX4008_DUM
1609 select FB_CFB_FILLRECT
1610 select FB_CFB_COPYAREA
1611 select FB_CFB_IMAGEBLIT
1612 ---help---
1613 Say Y here to enable support for PNX4008 RGB Framebuffer
1614
Linus Torvalds1da177e2005-04-16 15:20:36 -07001615config FB_VIRTUAL
1616 tristate "Virtual Frame Buffer support (ONLY FOR TESTING!)"
1617 depends on FB
1618 select FB_CFB_FILLRECT
1619 select FB_CFB_COPYAREA
1620 select FB_CFB_IMAGEBLIT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001621 ---help---
1622 This is a `virtual' frame buffer device. It operates on a chunk of
1623 unswappable kernel memory instead of on the memory of a graphics
1624 board. This means you cannot see any output sent to this frame
1625 buffer device, while it does consume precious memory. The main use
1626 of this frame buffer device is testing and debugging the frame
1627 buffer subsystem. Do NOT enable it for normal systems! To protect
1628 the innocent, it has to be enabled explicitly at boot time using the
1629 kernel option `video=vfb:'.
1630
1631 To compile this driver as a module, choose M here: the
Mike Frysinger66cf7512006-10-03 01:14:41 -07001632 module will be called vfb. In order to load it, you must use
1633 the vfb_enable=1 option.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001634
1635 If unsure, say N.
1636if VT
1637 source "drivers/video/console/Kconfig"
1638endif
1639
1640if FB || SGI_NEWPORT_CONSOLE
1641 source "drivers/video/logo/Kconfig"
1642endif
1643
Antonino A. Daplas256154f2006-07-30 03:04:17 -07001644if SYSFS
Linus Torvalds1da177e2005-04-16 15:20:36 -07001645 source "drivers/video/backlight/Kconfig"
1646endif
1647
1648endmenu
1649