blob: 0388065bb79451997f35edbdc7cd52f004d683ea [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001#ifndef CYPRESS_M8_H
2#define CYPRESS_M8_H
3
4/* definitions and function prototypes used for the cypress USB to Serial controller */
5
6/* For sending our feature buffer - controlling serial communication states */
7/* Linux HID has no support for serial devices so we do this through the driver */
8#define HID_REQ_GET_REPORT 0x01
9#define HID_REQ_SET_REPORT 0x09
10
11/* List other cypress USB to Serial devices here, and add them to the id_table */
12
13/* DeLorme Earthmate USB - a GPS device */
14#define VENDOR_ID_DELORME 0x1163
15#define PRODUCT_ID_EARTHMATEUSB 0x0100
Lonnie Mendez25b6f082005-05-10 17:09:52 -050016#define PRODUCT_ID_EARTHMATEUSB_LT20 0x0200
Linus Torvalds1da177e2005-04-16 15:20:36 -070017
18/* Cypress HID->COM RS232 Adapter */
19#define VENDOR_ID_CYPRESS 0x04b4
20#define PRODUCT_ID_CYPHIDCOM 0x5500
Lonnie Mendeza5c44e22006-03-01 10:45:24 -060021
Dmitry Shapin6f6f06e2008-03-04 15:25:10 -080022/* Powercom UPS, chip CY7C63723 */
23#define VENDOR_ID_POWERCOM 0x0d9f
24#define PRODUCT_ID_UPS 0x0002
25
Lonnie Mendeza5c44e22006-03-01 10:45:24 -060026/* Nokia CA-42 USB to serial cable */
27#define VENDOR_ID_DAZZLE 0x07d0
28#define PRODUCT_ID_CA42 0x4101
Linus Torvalds1da177e2005-04-16 15:20:36 -070029/* End of device listing */
30
31/* Used for setting / requesting serial line settings */
32#define CYPRESS_SET_CONFIG 0x01
33#define CYPRESS_GET_CONFIG 0x02
34
35/* Used for throttle control */
36#define THROTTLED 0x1
37#define ACTUALLY_THROTTLED 0x2
38
39/* chiptypes - used in case firmware differs from the generic form ... offering
40 * different baud speeds/etc.
41 */
42
43#define CT_EARTHMATE 0x01
44#define CT_CYPHIDCOM 0x02
Lonnie Mendeza5c44e22006-03-01 10:45:24 -060045#define CT_CA42V2 0x03
Linus Torvalds1da177e2005-04-16 15:20:36 -070046#define CT_GENERIC 0x0F
47/* End of chiptype definitions */
48
49/* RS-232 serial data communication protocol definitions */
50/* these are sent / read at byte 0 of the input/output hid reports */
51/* You can find these values defined in the CY4601 USB to Serial design notes */
52
53#define CONTROL_DTR 0x20 /* data terminal ready - flow control - host to device */
54#define UART_DSR 0x20 /* data set ready - flow control - device to host */
55#define CONTROL_RTS 0x10 /* request to send - flow control - host to device */
56#define UART_CTS 0x10 /* clear to send - flow control - device to host */
57#define UART_RI 0x10 /* ring indicator - modem - device to host */
58#define UART_CD 0x40 /* carrier detect - modem - device to host */
59#define CYP_ERROR 0x08 /* received from input report - device to host */
60/* Note - the below has nothing to to with the "feature report" reset */
61#define CONTROL_RESET 0x08 /* sent with output report - host to device */
62
63/* End of RS-232 protocol definitions */
64
65#endif /* CYPRESS_M8_H */