Oliver Hartkopp | ccb2963 | 2007-11-16 15:56:08 -0800 | [diff] [blame] | 1 | menu "CAN Device Drivers" |
| 2 | depends on CAN |
| 3 | |
| 4 | config CAN_VCAN |
| 5 | tristate "Virtual Local CAN Interface (vcan)" |
| 6 | depends on CAN |
| 7 | default N |
| 8 | ---help--- |
| 9 | Similar to the network loopback devices, vcan offers a |
| 10 | virtual local CAN interface. |
| 11 | |
| 12 | This driver can also be built as a module. If so, the module |
| 13 | will be called vcan. |
| 14 | |
Wolfgang Grandegger | 39549ee | 2009-05-15 23:39:29 +0000 | [diff] [blame] | 15 | config CAN_DEV |
| 16 | tristate "Platform CAN drivers with Netlink support" |
| 17 | depends on CAN |
| 18 | default Y |
| 19 | ---help--- |
| 20 | Enables the common framework for platform CAN drivers with Netlink |
| 21 | support. This is the standard library for CAN drivers. |
| 22 | If unsure, say Y. |
| 23 | |
| 24 | config CAN_CALC_BITTIMING |
| 25 | bool "CAN bit-timing calculation" |
| 26 | depends on CAN_DEV |
| 27 | default Y |
| 28 | ---help--- |
| 29 | If enabled, CAN bit-timing parameters will be calculated for the |
| 30 | bit-rate specified via Netlink argument "bitrate" when the device |
| 31 | get started. This works fine for the most common CAN controllers |
| 32 | with standard bit-rates but may fail for exotic bit-rates or CAN |
| 33 | source clock frequencies. Disabling saves some space, but then the |
| 34 | bit-timing parameters must be specified directly using the Netlink |
| 35 | arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw". |
| 36 | If unsure, say Y. |
| 37 | |
Marc Kleine-Budde | 68f4015 | 2009-09-22 14:46:57 -0700 | [diff] [blame] | 38 | config CAN_AT91 |
| 39 | tristate "Atmel AT91 onchip CAN controller" |
Oliver Hartkopp | b93cf3f | 2009-11-12 01:35:01 +0000 | [diff] [blame] | 40 | depends on CAN_DEV && ARCH_AT91SAM9263 |
Marc Kleine-Budde | 68f4015 | 2009-09-22 14:46:57 -0700 | [diff] [blame] | 41 | ---help--- |
| 42 | This is a driver for the SoC CAN controller in Atmel's AT91SAM9263. |
| 43 | |
Anant Gole | 3758bf2 | 2009-10-07 02:59:47 +0000 | [diff] [blame] | 44 | config CAN_TI_HECC |
| 45 | depends on CAN_DEV && ARCH_OMAP3 |
| 46 | tristate "TI High End CAN Controller" |
| 47 | ---help--- |
| 48 | Driver for TI HECC (High End CAN Controller) module found on many |
| 49 | TI devices. The device specifications are available from www.ti.com |
| 50 | |
Christian Pellegrin | e000016 | 2009-11-02 23:07:00 +0000 | [diff] [blame] | 51 | config CAN_MCP251X |
| 52 | tristate "Microchip MCP251x SPI CAN controllers" |
Geert Uytterhoeven | 231d52a | 2009-12-13 09:11:06 +0000 | [diff] [blame] | 53 | depends on CAN_DEV && SPI && HAS_DMA |
Christian Pellegrin | e000016 | 2009-11-02 23:07:00 +0000 | [diff] [blame] | 54 | ---help--- |
| 55 | Driver for the Microchip MCP251x SPI CAN controllers. |
| 56 | |
Barry Song | bbb8461 | 2009-12-10 23:46:28 +0000 | [diff] [blame] | 57 | config CAN_BFIN |
| 58 | depends on CAN_DEV && (BF534 || BF536 || BF537 || BF538 || BF539 || BF54x) |
| 59 | tristate "Analog Devices Blackfin on-chip CAN" |
| 60 | ---help--- |
| 61 | Driver for the Analog Devices Blackfin on-chip CAN controllers |
| 62 | |
| 63 | To compile this driver as a module, choose M here: the |
| 64 | module will be called bfin_can. |
| 65 | |
Wolfram Sang | 24cfbcb | 2009-11-17 03:57:12 -0800 | [diff] [blame] | 66 | source "drivers/net/can/mscan/Kconfig" |
Wolfram Sang | afa17a5 | 2009-11-13 06:14:52 +0000 | [diff] [blame] | 67 | |
Oliver Hartkopp | b93cf3f | 2009-11-12 01:35:01 +0000 | [diff] [blame] | 68 | source "drivers/net/can/sja1000/Kconfig" |
| 69 | |
| 70 | source "drivers/net/can/usb/Kconfig" |
| 71 | |
Oliver Hartkopp | ccb2963 | 2007-11-16 15:56:08 -0800 | [diff] [blame] | 72 | config CAN_DEBUG_DEVICES |
| 73 | bool "CAN devices debugging messages" |
| 74 | depends on CAN |
| 75 | default N |
| 76 | ---help--- |
| 77 | Say Y here if you want the CAN device drivers to produce a bunch of |
| 78 | debug messages to the system log. Select this if you are having |
| 79 | a problem with CAN support and want to see more of what is going |
| 80 | on. |
| 81 | |
| 82 | endmenu |