| Lokesh Kumar Aakulu | 2521350 | 2013-05-07 17:43:03 -0700 | [diff] [blame] | 1 | /* |
| 2 | * Copyright (c) 2013, The Linux Foundation. All rights reserved. |
| 3 | * |
| 4 | * This program is free software; you can redistribute it and/or modify |
| 5 | * it under the terms of the GNU General Public License version 2 and |
| 6 | * only version 2 as published by the Free Software Foundation. |
| 7 | * |
| 8 | * This program is distributed in the hope that it will be useful, |
| 9 | * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| 10 | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| 11 | * GNU General Public License for more details. |
| 12 | */ |
| 13 | |
| 14 | &i2c { |
| 15 | |
| 16 | led_flash0: qcom,led-flash@60 { |
| 17 | cell-index = <0>; |
| 18 | reg = <0x60>; |
| 19 | qcom,slave-id = <0x60 0x00 0x0011>; |
| 20 | compatible = "qcom,led-flash"; |
| 21 | qcom,flash-name = "adp1600"; |
| 22 | qcom,flash-type = <1>; |
| 23 | qcom,gpio-no-mux = <0>; |
| 24 | gpios = <&msmgpio 18 0>, |
| 25 | <&msmgpio 19 0>; |
| 26 | qcom,gpio-flash-en = <0>; |
| 27 | qcom,gpio-flash-now = <1>; |
| 28 | qcom,gpio-req-tbl-num = <0 1>; |
| 29 | qcom,gpio-req-tbl-flags = <0 0>; |
| 30 | qcom,gpio-req-tbl-label = "FLASH_EN", |
| 31 | "FLASH_NOW"; |
| 32 | }; |
| 33 | |
| 34 | actuator0: qcom,actuator@6e { |
| 35 | cell-index = <3>; |
| 36 | reg = <0x6c>; |
| 37 | compatible = "qcom,actuator"; |
| 38 | qcom,cci-master = <0>; |
| 39 | }; |
| 40 | |
| 41 | qcom,camera@6f { |
| 42 | compatible = "qcom,ov8825"; |
| 43 | reg = <0x6f>; |
| 44 | qcom,slave-id = <0x6c 0x300a 0x8825>; |
| 45 | qcom,csiphy-sd-index = <0>; |
| 46 | qcom,csid-sd-index = <0>; |
| 47 | qcom,actuator-src = <&actuator0>; |
| 48 | qcom,led-flash-src = <&led_flash0>; |
| 49 | qcom,mount-angle = <90>; |
| 50 | qcom,sensor-name = "ov8825"; |
| 51 | cam_vdig-supply = <&pm8110_l2>; |
| 52 | cam_vana-supply = <&pm8110_l19>; |
| 53 | cam_vio-supply = <&pm8110_l14>; |
| 54 | cam_vaf-supply = <&pm8110_l16>; |
| 55 | qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana", |
| 56 | "cam_vaf"; |
| 57 | qcom,cam-vreg-type = <0 0 0 0>; |
| 58 | qcom,cam-vreg-min-voltage = <1200000 1800000 2850000 3000000>; |
| 59 | qcom,cam-vreg-max-voltage = <1200000 1800000 2850000 3000000>; |
| 60 | qcom,cam-vreg-op-mode = <200000 8000 80000 100000>; |
| 61 | qcom,gpio-no-mux = <0>; |
| 62 | gpios = <&msmgpio 13 0>, |
| 63 | <&msmgpio 21 0>, |
| 64 | <&msmgpio 20 0>; |
| 65 | qcom,gpio-reset = <1>; |
| 66 | qcom,gpio-standby = <2>; |
| 67 | qcom,gpio-req-tbl-num = <0 1 2>; |
| 68 | qcom,gpio-req-tbl-flags = <1 0 0>; |
| 69 | qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| 70 | "CAM_RESET1", |
| 71 | "CAM_STANDBY"; |
| 72 | qcom,csi-lane-assign = <0xe4>; |
| 73 | qcom,csi-lane-mask = <0x3>; |
| 74 | qcom,sensor-position = <0>; |
| 75 | qcom,sensor-mode = <1>; |
| 76 | qcom,cci-master = <0>; |
| 77 | }; |
| 78 | |
| 79 | qcom,camera@6d { |
| 80 | compatible = "qcom,ov9724"; |
| 81 | reg = <0x6d>; |
| 82 | qcom,slave-id = <0x20 0x0 0x9724>; |
| 83 | qcom,csiphy-sd-index = <1>; |
| 84 | qcom,csid-sd-index = <0>; |
| 85 | qcom,mount-angle = <90>; |
| 86 | qcom,sensor-name = "ov9724"; |
| 87 | cam_vdig-supply = <&pm8110_l4>; |
| 88 | cam_vana-supply = <&pm8110_l19>; |
| 89 | cam_vio-supply = <&pm8110_l14>; |
| 90 | qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana"; |
| 91 | qcom,cam-vreg-type = <0 1 0>; |
| 92 | qcom,cam-vreg-min-voltage = <1200000 0 2850000>; |
| 93 | qcom,cam-vreg-max-voltage = <1200000 0 2850000>; |
| 94 | qcom,cam-vreg-op-mode = <200000 0 80000>; |
| 95 | qcom,gpio-no-mux = <0>; |
| 96 | gpios = <&msmgpio 14 0>, |
| 97 | <&msmgpio 15 0>, |
| 98 | <&msmgpio 8 0>; |
| 99 | qcom,gpio-reset = <1>; |
| 100 | qcom,gpio-standby = <2>; |
| 101 | qcom,gpio-req-tbl-num = <0 1 2>; |
| 102 | qcom,gpio-req-tbl-flags = <1 0 0>; |
| 103 | qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| 104 | "CAM_RESET", |
| 105 | "CAM_STANDBY"; |
| 106 | qcom,gpio-set-tbl-num = <1 1>; |
| 107 | qcom,gpio-set-tbl-flags = <0 2>; |
| 108 | qcom,gpio-set-tbl-delay = <1000 4000>; |
| 109 | qcom,csi-lane-assign = <0xe4>; |
| 110 | qcom,csi-lane-mask = <0x1>; |
| 111 | qcom,sensor-position = <1>; |
| 112 | qcom,sensor-mode = <1>; |
| 113 | qcom,cci-master = <0>; |
| 114 | status = "ok"; |
| 115 | }; |
| Ju He | f437ef8 | 2013-06-07 15:50:04 -0700 | [diff] [blame] | 116 | |
| 117 | qcom,camera@78 { |
| 118 | compatible = "qcom,sp1628"; |
| 119 | reg = <0x78>; |
| 120 | qcom,slave-id = <0x78 0x0 0x1628>; |
| 121 | qcom,csiphy-sd-index = <1>; |
| 122 | qcom,csid-sd-index = <1>; |
| 123 | qcom,mount-angle = <90>; |
| 124 | qcom,sensor-name = "sp1628"; |
| 125 | cam_vdig-supply = <&pm8110_l2>; |
| 126 | cam_vana-supply = <&pm8110_l19>; |
| 127 | cam_vio-supply = <&pm8110_l14>; |
| 128 | qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana"; |
| 129 | qcom,cam-vreg-type = <0 0 0>; |
| 130 | qcom,cam-vreg-min-voltage = <1200000 1800000 2850000>; |
| 131 | qcom,cam-vreg-max-voltage = <1200000 1800000 2850000>; |
| 132 | qcom,cam-vreg-op-mode = <200000 80000 80000>; |
| 133 | qcom,gpio-no-mux = <0>; |
| 134 | gpios = <&msmgpio 14 0>, |
| 135 | <&msmgpio 15 0>, |
| 136 | <&msmgpio 8 0>; |
| 137 | qcom,gpio-reset = <1>; |
| 138 | qcom,gpio-standby = <2>; |
| 139 | qcom,gpio-req-tbl-num = <0 1 2>; |
| 140 | qcom,gpio-req-tbl-flags = <1 0 0>; |
| 141 | qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| 142 | "CAM_RESET", |
| 143 | "CAM_STANDBY"; |
| 144 | qcom,gpio-set-tbl-num = <1 1>; |
| 145 | qcom,gpio-set-tbl-flags = <0 2>; |
| 146 | qcom,gpio-set-tbl-delay = <1000 4000>; |
| 147 | qcom,csi-lane-assign = <0xe4>; |
| 148 | qcom,csi-lane-mask = <0x3>; |
| 149 | qcom,sensor-position = <1>; |
| 150 | qcom,sensor-mode = <1>; |
| 151 | qcom,cci-master = <0>; |
| 152 | }; |
| 153 | |
| Lokesh Kumar Aakulu | 2521350 | 2013-05-07 17:43:03 -0700 | [diff] [blame] | 154 | }; |