blob: d085030df70ba5bd321a0fd5716df8ab31af39e1 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * drivers/serial/serial_txx9.c
3 *
4 * Derived from many drivers using generic_serial interface,
5 * especially serial_tx3912.c by Steven J. Hill and r39xx_serial.c
6 * (was in Linux/VR tree) by Jim Pick.
7 *
8 * Copyright (C) 1999 Harald Koerfgen
9 * Copyright (C) 2000 Jim Pick <jim@jimpick.com>
10 * Copyright (C) 2001 Steven J. Hill (sjhill@realitydiluted.com)
11 * Copyright (C) 2000-2002 Toshiba Corporation
12 *
13 * This program is free software; you can redistribute it and/or modify
14 * it under the terms of the GNU General Public License version 2 as
15 * published by the Free Software Foundation.
16 *
17 * Serial driver for TX3927/TX4927/TX4925/TX4938 internal SIO controller
18 *
19 * Revision History:
20 * 0.30 Initial revision. (Renamed from serial_txx927.c)
21 * 0.31 Use save_flags instead of local_irq_save.
22 * 0.32 Support SCLK.
23 * 0.33 Switch TXX9_TTY_NAME by CONFIG_SERIAL_TXX9_STDSERIAL.
24 * Support TIOCSERGETLSR.
25 * 0.34 Support slow baudrate.
26 * 0.40 Merge codes from mainstream kernel (2.4.22).
27 * 0.41 Fix console checking in rs_shutdown_port().
28 * Disable flow-control in serial_console_write().
29 * 0.42 Fix minor compiler warning.
30 * 1.00 Kernel 2.6. Converted to new serial core (based on 8250.c).
31 * 1.01 Set fifosize to make tx_empry called properly.
32 * Use standard uart_get_divisor.
33 * 1.02 Cleanup. (import 8250.c changes)
34 */
35#include <linux/config.h>
36
37#if defined(CONFIG_SERIAL_TXX9_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
38#define SUPPORT_SYSRQ
39#endif
40
41#include <linux/module.h>
42#include <linux/ioport.h>
43#include <linux/init.h>
44#include <linux/console.h>
45#include <linux/sysrq.h>
46#include <linux/delay.h>
47#include <linux/device.h>
48#include <linux/pci.h>
49#include <linux/tty.h>
50#include <linux/tty_flip.h>
51#include <linux/serial_core.h>
52#include <linux/serial.h>
53
54#include <asm/io.h>
55#include <asm/irq.h>
56
57static char *serial_version = "1.02";
58static char *serial_name = "TX39/49 Serial driver";
59
60#define PASS_LIMIT 256
61
62#if !defined(CONFIG_SERIAL_TXX9_STDSERIAL)
63/* "ttyS" is used for standard serial driver */
64#define TXX9_TTY_NAME "ttyTX"
65#define TXX9_TTY_DEVFS_NAME "tttx/"
66#define TXX9_TTY_MINOR_START (64 + 64) /* ttyTX0(128), ttyTX1(129) */
67#else
68/* acts like standard serial driver */
69#define TXX9_TTY_NAME "ttyS"
70#define TXX9_TTY_DEVFS_NAME "tts/"
71#define TXX9_TTY_MINOR_START 64
72#endif
73#define TXX9_TTY_MAJOR TTY_MAJOR
74
75/* flag aliases */
76#define UPF_TXX9_HAVE_CTS_LINE UPF_BUGGY_UART
77#define UPF_TXX9_USE_SCLK UPF_MAGIC_MULTIPLIER
78
79#ifdef CONFIG_PCI
80/* support for Toshiba TC86C001 SIO */
81#define ENABLE_SERIAL_TXX9_PCI
82#endif
83
84/*
85 * Number of serial ports
86 */
87#ifdef ENABLE_SERIAL_TXX9_PCI
88#define NR_PCI_BOARDS 4
89#define UART_NR (2 + NR_PCI_BOARDS)
90#else
91#define UART_NR 2
92#endif
93
94struct uart_txx9_port {
95 struct uart_port port;
96
97 /*
98 * We provide a per-port pm hook.
99 */
100 void (*pm)(struct uart_port *port,
101 unsigned int state, unsigned int old);
102};
103
104#define TXX9_REGION_SIZE 0x24
105
106/* TXX9 Serial Registers */
107#define TXX9_SILCR 0x00
108#define TXX9_SIDICR 0x04
109#define TXX9_SIDISR 0x08
110#define TXX9_SICISR 0x0c
111#define TXX9_SIFCR 0x10
112#define TXX9_SIFLCR 0x14
113#define TXX9_SIBGR 0x18
114#define TXX9_SITFIFO 0x1c
115#define TXX9_SIRFIFO 0x20
116
117/* SILCR : Line Control */
118#define TXX9_SILCR_SCS_MASK 0x00000060
119#define TXX9_SILCR_SCS_IMCLK 0x00000000
120#define TXX9_SILCR_SCS_IMCLK_BG 0x00000020
121#define TXX9_SILCR_SCS_SCLK 0x00000040
122#define TXX9_SILCR_SCS_SCLK_BG 0x00000060
123#define TXX9_SILCR_UEPS 0x00000010
124#define TXX9_SILCR_UPEN 0x00000008
125#define TXX9_SILCR_USBL_MASK 0x00000004
126#define TXX9_SILCR_USBL_1BIT 0x00000000
127#define TXX9_SILCR_USBL_2BIT 0x00000004
128#define TXX9_SILCR_UMODE_MASK 0x00000003
129#define TXX9_SILCR_UMODE_8BIT 0x00000000
130#define TXX9_SILCR_UMODE_7BIT 0x00000001
131
132/* SIDICR : DMA/Int. Control */
133#define TXX9_SIDICR_TDE 0x00008000
134#define TXX9_SIDICR_RDE 0x00004000
135#define TXX9_SIDICR_TIE 0x00002000
136#define TXX9_SIDICR_RIE 0x00001000
137#define TXX9_SIDICR_SPIE 0x00000800
138#define TXX9_SIDICR_CTSAC 0x00000600
139#define TXX9_SIDICR_STIE_MASK 0x0000003f
140#define TXX9_SIDICR_STIE_OERS 0x00000020
141#define TXX9_SIDICR_STIE_CTSS 0x00000010
142#define TXX9_SIDICR_STIE_RBRKD 0x00000008
143#define TXX9_SIDICR_STIE_TRDY 0x00000004
144#define TXX9_SIDICR_STIE_TXALS 0x00000002
145#define TXX9_SIDICR_STIE_UBRKD 0x00000001
146
147/* SIDISR : DMA/Int. Status */
148#define TXX9_SIDISR_UBRK 0x00008000
149#define TXX9_SIDISR_UVALID 0x00004000
150#define TXX9_SIDISR_UFER 0x00002000
151#define TXX9_SIDISR_UPER 0x00001000
152#define TXX9_SIDISR_UOER 0x00000800
153#define TXX9_SIDISR_ERI 0x00000400
154#define TXX9_SIDISR_TOUT 0x00000200
155#define TXX9_SIDISR_TDIS 0x00000100
156#define TXX9_SIDISR_RDIS 0x00000080
157#define TXX9_SIDISR_STIS 0x00000040
158#define TXX9_SIDISR_RFDN_MASK 0x0000001f
159
160/* SICISR : Change Int. Status */
161#define TXX9_SICISR_OERS 0x00000020
162#define TXX9_SICISR_CTSS 0x00000010
163#define TXX9_SICISR_RBRKD 0x00000008
164#define TXX9_SICISR_TRDY 0x00000004
165#define TXX9_SICISR_TXALS 0x00000002
166#define TXX9_SICISR_UBRKD 0x00000001
167
168/* SIFCR : FIFO Control */
169#define TXX9_SIFCR_SWRST 0x00008000
170#define TXX9_SIFCR_RDIL_MASK 0x00000180
171#define TXX9_SIFCR_RDIL_1 0x00000000
172#define TXX9_SIFCR_RDIL_4 0x00000080
173#define TXX9_SIFCR_RDIL_8 0x00000100
174#define TXX9_SIFCR_RDIL_12 0x00000180
175#define TXX9_SIFCR_RDIL_MAX 0x00000180
176#define TXX9_SIFCR_TDIL_MASK 0x00000018
177#define TXX9_SIFCR_TDIL_MASK 0x00000018
178#define TXX9_SIFCR_TDIL_1 0x00000000
179#define TXX9_SIFCR_TDIL_4 0x00000001
180#define TXX9_SIFCR_TDIL_8 0x00000010
181#define TXX9_SIFCR_TDIL_MAX 0x00000010
182#define TXX9_SIFCR_TFRST 0x00000004
183#define TXX9_SIFCR_RFRST 0x00000002
184#define TXX9_SIFCR_FRSTE 0x00000001
185#define TXX9_SIO_TX_FIFO 8
186#define TXX9_SIO_RX_FIFO 16
187
188/* SIFLCR : Flow Control */
189#define TXX9_SIFLCR_RCS 0x00001000
190#define TXX9_SIFLCR_TES 0x00000800
191#define TXX9_SIFLCR_RTSSC 0x00000200
192#define TXX9_SIFLCR_RSDE 0x00000100
193#define TXX9_SIFLCR_TSDE 0x00000080
194#define TXX9_SIFLCR_RTSTL_MASK 0x0000001e
195#define TXX9_SIFLCR_RTSTL_MAX 0x0000001e
196#define TXX9_SIFLCR_TBRK 0x00000001
197
198/* SIBGR : Baudrate Control */
199#define TXX9_SIBGR_BCLK_MASK 0x00000300
200#define TXX9_SIBGR_BCLK_T0 0x00000000
201#define TXX9_SIBGR_BCLK_T2 0x00000100
202#define TXX9_SIBGR_BCLK_T4 0x00000200
203#define TXX9_SIBGR_BCLK_T6 0x00000300
204#define TXX9_SIBGR_BRD_MASK 0x000000ff
205
206static inline unsigned int sio_in(struct uart_txx9_port *up, int offset)
207{
208 switch (up->port.iotype) {
209 default:
210 return *(volatile u32 *)(up->port.membase + offset);
211 case UPIO_PORT:
212 return inl(up->port.iobase + offset);
213 }
214}
215
216static inline void
217sio_out(struct uart_txx9_port *up, int offset, int value)
218{
219 switch (up->port.iotype) {
220 default:
221 *(volatile u32 *)(up->port.membase + offset) = value;
222 break;
223 case UPIO_PORT:
224 outl(value, up->port.iobase + offset);
225 break;
226 }
227}
228
229static inline void
230sio_mask(struct uart_txx9_port *up, int offset, unsigned int value)
231{
232 sio_out(up, offset, sio_in(up, offset) & ~value);
233}
234static inline void
235sio_set(struct uart_txx9_port *up, int offset, unsigned int value)
236{
237 sio_out(up, offset, sio_in(up, offset) | value);
238}
239
240static inline void
241sio_quot_set(struct uart_txx9_port *up, int quot)
242{
243 quot >>= 1;
244 if (quot < 256)
245 sio_out(up, TXX9_SIBGR, quot | TXX9_SIBGR_BCLK_T0);
246 else if (quot < (256 << 2))
247 sio_out(up, TXX9_SIBGR, (quot >> 2) | TXX9_SIBGR_BCLK_T2);
248 else if (quot < (256 << 4))
249 sio_out(up, TXX9_SIBGR, (quot >> 4) | TXX9_SIBGR_BCLK_T4);
250 else if (quot < (256 << 6))
251 sio_out(up, TXX9_SIBGR, (quot >> 6) | TXX9_SIBGR_BCLK_T6);
252 else
253 sio_out(up, TXX9_SIBGR, 0xff | TXX9_SIBGR_BCLK_T6);
254}
255
256static void serial_txx9_stop_tx(struct uart_port *port, unsigned int tty_stop)
257{
258 struct uart_txx9_port *up = (struct uart_txx9_port *)port;
259 unsigned long flags;
260
261 spin_lock_irqsave(&up->port.lock, flags);
262 sio_mask(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
263 spin_unlock_irqrestore(&up->port.lock, flags);
264}
265
266static void serial_txx9_start_tx(struct uart_port *port, unsigned int tty_start)
267{
268 struct uart_txx9_port *up = (struct uart_txx9_port *)port;
269 unsigned long flags;
270
271 spin_lock_irqsave(&up->port.lock, flags);
272 sio_set(up, TXX9_SIDICR, TXX9_SIDICR_TIE);
273 spin_unlock_irqrestore(&up->port.lock, flags);
274}
275
276static void serial_txx9_stop_rx(struct uart_port *port)
277{
278 struct uart_txx9_port *up = (struct uart_txx9_port *)port;
279 unsigned long flags;
280
281 spin_lock_irqsave(&up->port.lock, flags);
282 up->port.read_status_mask &= ~TXX9_SIDISR_RDIS;
283#if 0
284 sio_mask(up, TXX9_SIDICR, TXX9_SIDICR_RIE);
285#endif
286 spin_unlock_irqrestore(&up->port.lock, flags);
287}
288
289static void serial_txx9_enable_ms(struct uart_port *port)
290{
291 /* TXX9-SIO can not control DTR... */
292}
293
294static inline void
295receive_chars(struct uart_txx9_port *up, unsigned int *status, struct pt_regs *regs)
296{
297 struct tty_struct *tty = up->port.info->tty;
298 unsigned char ch;
299 unsigned int disr = *status;
300 int max_count = 256;
301 char flag;
302
303 do {
304 /* The following is not allowed by the tty layer and
305 unsafe. It should be fixed ASAP */
306 if (unlikely(tty->flip.count >= TTY_FLIPBUF_SIZE)) {
307 if(tty->low_latency)
308 tty_flip_buffer_push(tty);
309 /* If this failed then we will throw away the
310 bytes but must do so to clear interrupts */
311 }
312 ch = sio_in(up, TXX9_SIRFIFO);
313 flag = TTY_NORMAL;
314 up->port.icount.rx++;
315
316 if (unlikely(disr & (TXX9_SIDISR_UBRK | TXX9_SIDISR_UPER |
317 TXX9_SIDISR_UFER | TXX9_SIDISR_UOER))) {
318 /*
319 * For statistics only
320 */
321 if (disr & TXX9_SIDISR_UBRK) {
322 disr &= ~(TXX9_SIDISR_UFER | TXX9_SIDISR_UPER);
323 up->port.icount.brk++;
324 /*
325 * We do the SysRQ and SAK checking
326 * here because otherwise the break
327 * may get masked by ignore_status_mask
328 * or read_status_mask.
329 */
330 if (uart_handle_break(&up->port))
331 goto ignore_char;
332 } else if (disr & TXX9_SIDISR_UPER)
333 up->port.icount.parity++;
334 else if (disr & TXX9_SIDISR_UFER)
335 up->port.icount.frame++;
336 if (disr & TXX9_SIDISR_UOER)
337 up->port.icount.overrun++;
338
339 /*
340 * Mask off conditions which should be ingored.
341 */
342 disr &= up->port.read_status_mask;
343
344 if (disr & TXX9_SIDISR_UBRK) {
345 flag = TTY_BREAK;
346 } else if (disr & TXX9_SIDISR_UPER)
347 flag = TTY_PARITY;
348 else if (disr & TXX9_SIDISR_UFER)
349 flag = TTY_FRAME;
350 }
351 if (uart_handle_sysrq_char(&up->port, ch, regs))
352 goto ignore_char;
Russell King05ab3012005-05-09 23:21:59 +0100353
354 uart_insert_char(&up->port, disr, TXX9_SIDISR_UOER, ch, flag);
355
Linus Torvalds1da177e2005-04-16 15:20:36 -0700356 ignore_char:
357 disr = sio_in(up, TXX9_SIDISR);
358 } while (!(disr & TXX9_SIDISR_UVALID) && (max_count-- > 0));
359 tty_flip_buffer_push(tty);
360 *status = disr;
361}
362
363static inline void transmit_chars(struct uart_txx9_port *up)
364{
365 struct circ_buf *xmit = &up->port.info->xmit;
366 int count;
367
368 if (up->port.x_char) {
369 sio_out(up, TXX9_SITFIFO, up->port.x_char);
370 up->port.icount.tx++;
371 up->port.x_char = 0;
372 return;
373 }
374 if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
375 serial_txx9_stop_tx(&up->port, 0);
376 return;
377 }
378
379 count = TXX9_SIO_TX_FIFO;
380 do {
381 sio_out(up, TXX9_SITFIFO, xmit->buf[xmit->tail]);
382 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
383 up->port.icount.tx++;
384 if (uart_circ_empty(xmit))
385 break;
386 } while (--count > 0);
387
388 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
389 uart_write_wakeup(&up->port);
390
391 if (uart_circ_empty(xmit))
392 serial_txx9_stop_tx(&up->port, 0);
393}
394
395static irqreturn_t serial_txx9_interrupt(int irq, void *dev_id, struct pt_regs *regs)
396{
397 int pass_counter = 0;
398 struct uart_txx9_port *up = dev_id;
399 unsigned int status;
400
401 while (1) {
402 spin_lock(&up->port.lock);
403 status = sio_in(up, TXX9_SIDISR);
404 if (!(sio_in(up, TXX9_SIDICR) & TXX9_SIDICR_TIE))
405 status &= ~TXX9_SIDISR_TDIS;
406 if (!(status & (TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS |
407 TXX9_SIDISR_TOUT))) {
408 spin_unlock(&up->port.lock);
409 break;
410 }
411
412 if (status & TXX9_SIDISR_RDIS)
413 receive_chars(up, &status, regs);
414 if (status & TXX9_SIDISR_TDIS)
415 transmit_chars(up);
416 /* Clear TX/RX Int. Status */
417 sio_mask(up, TXX9_SIDISR,
418 TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS |
419 TXX9_SIDISR_TOUT);
420 spin_unlock(&up->port.lock);
421
422 if (pass_counter++ > PASS_LIMIT)
423 break;
424 }
425
426 return pass_counter ? IRQ_HANDLED : IRQ_NONE;
427}
428
429static unsigned int serial_txx9_tx_empty(struct uart_port *port)
430{
431 struct uart_txx9_port *up = (struct uart_txx9_port *)port;
432 unsigned long flags;
433 unsigned int ret;
434
435 spin_lock_irqsave(&up->port.lock, flags);
436 ret = (sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS) ? TIOCSER_TEMT : 0;
437 spin_unlock_irqrestore(&up->port.lock, flags);
438
439 return ret;
440}
441
442static unsigned int serial_txx9_get_mctrl(struct uart_port *port)
443{
444 struct uart_txx9_port *up = (struct uart_txx9_port *)port;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700445 unsigned int ret;
446
Linus Torvalds1da177e2005-04-16 15:20:36 -0700447 ret = ((sio_in(up, TXX9_SIFLCR) & TXX9_SIFLCR_RTSSC) ? 0 : TIOCM_RTS)
448 | ((sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS) ? 0 : TIOCM_CTS);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700449
450 return ret;
451}
452
453static void serial_txx9_set_mctrl(struct uart_port *port, unsigned int mctrl)
454{
455 struct uart_txx9_port *up = (struct uart_txx9_port *)port;
456 unsigned long flags;
457
458 spin_lock_irqsave(&up->port.lock, flags);
459 if (mctrl & TIOCM_RTS)
460 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
461 else
462 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSSC);
463 spin_unlock_irqrestore(&up->port.lock, flags);
464}
465
466static void serial_txx9_break_ctl(struct uart_port *port, int break_state)
467{
468 struct uart_txx9_port *up = (struct uart_txx9_port *)port;
469 unsigned long flags;
470
471 spin_lock_irqsave(&up->port.lock, flags);
472 if (break_state == -1)
473 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
474 else
475 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
476 spin_unlock_irqrestore(&up->port.lock, flags);
477}
478
479static int serial_txx9_startup(struct uart_port *port)
480{
481 struct uart_txx9_port *up = (struct uart_txx9_port *)port;
482 unsigned long flags;
483 int retval;
484
485 /*
486 * Clear the FIFO buffers and disable them.
487 * (they will be reeanbled in set_termios())
488 */
489 sio_set(up, TXX9_SIFCR,
490 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
491 /* clear reset */
492 sio_mask(up, TXX9_SIFCR,
493 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
494 sio_out(up, TXX9_SIDICR, 0);
495
496 /*
497 * Clear the interrupt registers.
498 */
499 sio_out(up, TXX9_SIDISR, 0);
500
501 retval = request_irq(up->port.irq, serial_txx9_interrupt,
502 SA_SHIRQ, "serial_txx9", up);
503 if (retval)
504 return retval;
505
506 /*
507 * Now, initialize the UART
508 */
509 spin_lock_irqsave(&up->port.lock, flags);
510 serial_txx9_set_mctrl(&up->port, up->port.mctrl);
511 spin_unlock_irqrestore(&up->port.lock, flags);
512
513 /* Enable RX/TX */
514 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE);
515
516 /*
517 * Finally, enable interrupts.
518 */
519 sio_set(up, TXX9_SIDICR, TXX9_SIDICR_RIE);
520
521 return 0;
522}
523
524static void serial_txx9_shutdown(struct uart_port *port)
525{
526 struct uart_txx9_port *up = (struct uart_txx9_port *)port;
527 unsigned long flags;
528
529 /*
530 * Disable interrupts from this port
531 */
532 sio_out(up, TXX9_SIDICR, 0); /* disable all intrs */
533
534 spin_lock_irqsave(&up->port.lock, flags);
535 serial_txx9_set_mctrl(&up->port, up->port.mctrl);
536 spin_unlock_irqrestore(&up->port.lock, flags);
537
538 /*
539 * Disable break condition
540 */
541 sio_mask(up, TXX9_SIFLCR, TXX9_SIFLCR_TBRK);
542
543#ifdef CONFIG_SERIAL_TXX9_CONSOLE
544 if (up->port.cons && up->port.line == up->port.cons->index) {
545 free_irq(up->port.irq, up);
546 return;
547 }
548#endif
549 /* reset FIFOs */
550 sio_set(up, TXX9_SIFCR,
551 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
552 /* clear reset */
553 sio_mask(up, TXX9_SIFCR,
554 TXX9_SIFCR_TFRST | TXX9_SIFCR_RFRST | TXX9_SIFCR_FRSTE);
555
556 /* Disable RX/TX */
557 sio_set(up, TXX9_SIFLCR, TXX9_SIFLCR_RSDE | TXX9_SIFLCR_TSDE);
558
559 free_irq(up->port.irq, up);
560}
561
562static void
563serial_txx9_set_termios(struct uart_port *port, struct termios *termios,
564 struct termios *old)
565{
566 struct uart_txx9_port *up = (struct uart_txx9_port *)port;
567 unsigned int cval, fcr = 0;
568 unsigned long flags;
569 unsigned int baud, quot;
570
571 cval = sio_in(up, TXX9_SILCR);
572 /* byte size and parity */
573 cval &= ~TXX9_SILCR_UMODE_MASK;
574 switch (termios->c_cflag & CSIZE) {
575 case CS7:
576 cval |= TXX9_SILCR_UMODE_7BIT;
577 break;
578 default:
579 case CS5: /* not supported */
580 case CS6: /* not supported */
581 case CS8:
582 cval |= TXX9_SILCR_UMODE_8BIT;
583 break;
584 }
585
586 cval &= ~TXX9_SILCR_USBL_MASK;
587 if (termios->c_cflag & CSTOPB)
588 cval |= TXX9_SILCR_USBL_2BIT;
589 else
590 cval |= TXX9_SILCR_USBL_1BIT;
591 cval &= ~(TXX9_SILCR_UPEN | TXX9_SILCR_UEPS);
592 if (termios->c_cflag & PARENB)
593 cval |= TXX9_SILCR_UPEN;
594 if (!(termios->c_cflag & PARODD))
595 cval |= TXX9_SILCR_UEPS;
596
597 /*
598 * Ask the core to calculate the divisor for us.
599 */
600 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16/2);
601 quot = uart_get_divisor(port, baud);
602
603 /* Set up FIFOs */
604 /* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
605 fcr = TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1;
606
607 /*
608 * Ok, we're now changing the port state. Do it with
609 * interrupts disabled.
610 */
611 spin_lock_irqsave(&up->port.lock, flags);
612
613 /*
614 * Update the per-port timeout.
615 */
616 uart_update_timeout(port, termios->c_cflag, baud);
617
618 up->port.read_status_mask = TXX9_SIDISR_UOER |
619 TXX9_SIDISR_TDIS | TXX9_SIDISR_RDIS;
620 if (termios->c_iflag & INPCK)
621 up->port.read_status_mask |= TXX9_SIDISR_UFER | TXX9_SIDISR_UPER;
622 if (termios->c_iflag & (BRKINT | PARMRK))
623 up->port.read_status_mask |= TXX9_SIDISR_UBRK;
624
625 /*
626 * Characteres to ignore
627 */
628 up->port.ignore_status_mask = 0;
629 if (termios->c_iflag & IGNPAR)
630 up->port.ignore_status_mask |= TXX9_SIDISR_UPER | TXX9_SIDISR_UFER;
631 if (termios->c_iflag & IGNBRK) {
632 up->port.ignore_status_mask |= TXX9_SIDISR_UBRK;
633 /*
634 * If we're ignoring parity and break indicators,
635 * ignore overruns too (for real raw support).
636 */
637 if (termios->c_iflag & IGNPAR)
638 up->port.ignore_status_mask |= TXX9_SIDISR_UOER;
639 }
640
641 /*
642 * ignore all characters if CREAD is not set
643 */
644 if ((termios->c_cflag & CREAD) == 0)
645 up->port.ignore_status_mask |= TXX9_SIDISR_RDIS;
646
647 /* CTS flow control flag */
648 if ((termios->c_cflag & CRTSCTS) &&
649 (up->port.flags & UPF_TXX9_HAVE_CTS_LINE)) {
650 sio_set(up, TXX9_SIFLCR,
651 TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES);
652 } else {
653 sio_mask(up, TXX9_SIFLCR,
654 TXX9_SIFLCR_RCS | TXX9_SIFLCR_TES);
655 }
656
657 sio_out(up, TXX9_SILCR, cval);
658 sio_quot_set(up, quot);
659 sio_out(up, TXX9_SIFCR, fcr);
660
661 serial_txx9_set_mctrl(&up->port, up->port.mctrl);
662 spin_unlock_irqrestore(&up->port.lock, flags);
663}
664
665static void
666serial_txx9_pm(struct uart_port *port, unsigned int state,
667 unsigned int oldstate)
668{
669 struct uart_txx9_port *up = (struct uart_txx9_port *)port;
670 if (state) {
671 /* sleep */
672
673 if (up->pm)
674 up->pm(port, state, oldstate);
675 } else {
676 /* wake */
677
678 if (up->pm)
679 up->pm(port, state, oldstate);
680 }
681}
682
683static int serial_txx9_request_resource(struct uart_txx9_port *up)
684{
685 unsigned int size = TXX9_REGION_SIZE;
686 int ret = 0;
687
688 switch (up->port.iotype) {
689 default:
690 if (!up->port.mapbase)
691 break;
692
693 if (!request_mem_region(up->port.mapbase, size, "serial_txx9")) {
694 ret = -EBUSY;
695 break;
696 }
697
698 if (up->port.flags & UPF_IOREMAP) {
699 up->port.membase = ioremap(up->port.mapbase, size);
700 if (!up->port.membase) {
701 release_mem_region(up->port.mapbase, size);
702 ret = -ENOMEM;
703 }
704 }
705 break;
706
707 case UPIO_PORT:
708 if (!request_region(up->port.iobase, size, "serial_txx9"))
709 ret = -EBUSY;
710 break;
711 }
712 return ret;
713}
714
715static void serial_txx9_release_resource(struct uart_txx9_port *up)
716{
717 unsigned int size = TXX9_REGION_SIZE;
718
719 switch (up->port.iotype) {
720 default:
721 if (!up->port.mapbase)
722 break;
723
724 if (up->port.flags & UPF_IOREMAP) {
725 iounmap(up->port.membase);
726 up->port.membase = NULL;
727 }
728
729 release_mem_region(up->port.mapbase, size);
730 break;
731
732 case UPIO_PORT:
733 release_region(up->port.iobase, size);
734 break;
735 }
736}
737
738static void serial_txx9_release_port(struct uart_port *port)
739{
740 struct uart_txx9_port *up = (struct uart_txx9_port *)port;
741 serial_txx9_release_resource(up);
742}
743
744static int serial_txx9_request_port(struct uart_port *port)
745{
746 struct uart_txx9_port *up = (struct uart_txx9_port *)port;
747 return serial_txx9_request_resource(up);
748}
749
750static void serial_txx9_config_port(struct uart_port *port, int uflags)
751{
752 struct uart_txx9_port *up = (struct uart_txx9_port *)port;
753 unsigned long flags;
754 int ret;
755
756 /*
757 * Find the region that we can probe for. This in turn
758 * tells us whether we can probe for the type of port.
759 */
760 ret = serial_txx9_request_resource(up);
761 if (ret < 0)
762 return;
763 port->type = PORT_TXX9;
764 up->port.fifosize = TXX9_SIO_TX_FIFO;
765
766#ifdef CONFIG_SERIAL_TXX9_CONSOLE
767 if (up->port.line == up->port.cons->index)
768 return;
769#endif
770 spin_lock_irqsave(&up->port.lock, flags);
771 /*
772 * Reset the UART.
773 */
774 sio_out(up, TXX9_SIFCR, TXX9_SIFCR_SWRST);
775#ifdef CONFIG_CPU_TX49XX
776 /* TX4925 BUG WORKAROUND. Accessing SIOC register
777 * immediately after soft reset causes bus error. */
778 iob();
779 udelay(1);
780#endif
781 while (sio_in(up, TXX9_SIFCR) & TXX9_SIFCR_SWRST)
782 ;
783 /* TX Int by FIFO Empty, RX Int by Receiving 1 char. */
784 sio_set(up, TXX9_SIFCR,
785 TXX9_SIFCR_TDIL_MAX | TXX9_SIFCR_RDIL_1);
786 /* initial settings */
787 sio_out(up, TXX9_SILCR,
788 TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT |
789 ((up->port.flags & UPF_TXX9_USE_SCLK) ?
790 TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG));
791 sio_quot_set(up, uart_get_divisor(port, 9600));
792 sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */);
793 spin_unlock_irqrestore(&up->port.lock, flags);
794}
795
796static int
797serial_txx9_verify_port(struct uart_port *port, struct serial_struct *ser)
798{
799 if (ser->irq < 0 ||
800 ser->baud_base < 9600 || ser->type != PORT_TXX9)
801 return -EINVAL;
802 return 0;
803}
804
805static const char *
806serial_txx9_type(struct uart_port *port)
807{
808 return "txx9";
809}
810
811static struct uart_ops serial_txx9_pops = {
812 .tx_empty = serial_txx9_tx_empty,
813 .set_mctrl = serial_txx9_set_mctrl,
814 .get_mctrl = serial_txx9_get_mctrl,
815 .stop_tx = serial_txx9_stop_tx,
816 .start_tx = serial_txx9_start_tx,
817 .stop_rx = serial_txx9_stop_rx,
818 .enable_ms = serial_txx9_enable_ms,
819 .break_ctl = serial_txx9_break_ctl,
820 .startup = serial_txx9_startup,
821 .shutdown = serial_txx9_shutdown,
822 .set_termios = serial_txx9_set_termios,
823 .pm = serial_txx9_pm,
824 .type = serial_txx9_type,
825 .release_port = serial_txx9_release_port,
826 .request_port = serial_txx9_request_port,
827 .config_port = serial_txx9_config_port,
828 .verify_port = serial_txx9_verify_port,
829};
830
831static struct uart_txx9_port serial_txx9_ports[UART_NR];
832
833static void __init serial_txx9_register_ports(struct uart_driver *drv)
834{
835 int i;
836
837 for (i = 0; i < UART_NR; i++) {
838 struct uart_txx9_port *up = &serial_txx9_ports[i];
839
840 up->port.line = i;
841 up->port.ops = &serial_txx9_pops;
842 uart_add_one_port(drv, &up->port);
843 }
844}
845
846#ifdef CONFIG_SERIAL_TXX9_CONSOLE
847
848/*
849 * Wait for transmitter & holding register to empty
850 */
851static inline void wait_for_xmitr(struct uart_txx9_port *up)
852{
853 unsigned int tmout = 10000;
854
855 /* Wait up to 10ms for the character(s) to be sent. */
856 while (--tmout &&
857 !(sio_in(up, TXX9_SICISR) & TXX9_SICISR_TXALS))
858 udelay(1);
859
860 /* Wait up to 1s for flow control if necessary */
861 if (up->port.flags & UPF_CONS_FLOW) {
862 tmout = 1000000;
863 while (--tmout &&
864 (sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS))
865 udelay(1);
866 }
867}
868
869/*
870 * Print a string to the serial port trying not to disturb
871 * any possible real use of the port...
872 *
873 * The console_lock must be held when we get here.
874 */
875static void
876serial_txx9_console_write(struct console *co, const char *s, unsigned int count)
877{
878 struct uart_txx9_port *up = &serial_txx9_ports[co->index];
879 unsigned int ier, flcr;
880 int i;
881
882 /*
883 * First save the UER then disable the interrupts
884 */
885 ier = sio_in(up, TXX9_SIDICR);
886 sio_out(up, TXX9_SIDICR, 0);
887 /*
888 * Disable flow-control if enabled (and unnecessary)
889 */
890 flcr = sio_in(up, TXX9_SIFLCR);
891 if (!(up->port.flags & UPF_CONS_FLOW) && (flcr & TXX9_SIFLCR_TES))
892 sio_out(up, TXX9_SIFLCR, flcr & ~TXX9_SIFLCR_TES);
893
894 /*
895 * Now, do each character
896 */
897 for (i = 0; i < count; i++, s++) {
898 wait_for_xmitr(up);
899
900 /*
901 * Send the character out.
902 * If a LF, also do CR...
903 */
904 sio_out(up, TXX9_SITFIFO, *s);
905 if (*s == 10) {
906 wait_for_xmitr(up);
907 sio_out(up, TXX9_SITFIFO, 13);
908 }
909 }
910
911 /*
912 * Finally, wait for transmitter to become empty
913 * and restore the IER
914 */
915 wait_for_xmitr(up);
916 sio_out(up, TXX9_SIFLCR, flcr);
917 sio_out(up, TXX9_SIDICR, ier);
918}
919
920static int serial_txx9_console_setup(struct console *co, char *options)
921{
922 struct uart_port *port;
923 struct uart_txx9_port *up;
924 int baud = 9600;
925 int bits = 8;
926 int parity = 'n';
927 int flow = 'n';
928
929 /*
930 * Check whether an invalid uart number has been specified, and
931 * if so, search for the first available port that does have
932 * console support.
933 */
934 if (co->index >= UART_NR)
935 co->index = 0;
936 up = &serial_txx9_ports[co->index];
937 port = &up->port;
938 if (!port->ops)
939 return -ENODEV;
940
941 /*
942 * Temporary fix.
943 */
944 spin_lock_init(&port->lock);
945
946 /*
947 * Disable UART interrupts, set DTR and RTS high
948 * and set speed.
949 */
950 sio_out(up, TXX9_SIDICR, 0);
951 /* initial settings */
952 sio_out(up, TXX9_SILCR,
953 TXX9_SILCR_UMODE_8BIT | TXX9_SILCR_USBL_1BIT |
954 ((port->flags & UPF_TXX9_USE_SCLK) ?
955 TXX9_SILCR_SCS_SCLK_BG : TXX9_SILCR_SCS_IMCLK_BG));
956 sio_out(up, TXX9_SIFLCR, TXX9_SIFLCR_RTSTL_MAX /* 15 */);
957
958 if (options)
959 uart_parse_options(options, &baud, &parity, &bits, &flow);
960
961 return uart_set_options(port, co, baud, parity, bits, flow);
962}
963
964static struct uart_driver serial_txx9_reg;
965static struct console serial_txx9_console = {
966 .name = TXX9_TTY_NAME,
967 .write = serial_txx9_console_write,
968 .device = uart_console_device,
969 .setup = serial_txx9_console_setup,
970 .flags = CON_PRINTBUFFER,
971 .index = -1,
972 .data = &serial_txx9_reg,
973};
974
975static int __init serial_txx9_console_init(void)
976{
977 register_console(&serial_txx9_console);
978 return 0;
979}
980console_initcall(serial_txx9_console_init);
981
982static int __init serial_txx9_late_console_init(void)
983{
984 if (!(serial_txx9_console.flags & CON_ENABLED))
985 register_console(&serial_txx9_console);
986 return 0;
987}
988late_initcall(serial_txx9_late_console_init);
989
990#define SERIAL_TXX9_CONSOLE &serial_txx9_console
991#else
992#define SERIAL_TXX9_CONSOLE NULL
993#endif
994
995static struct uart_driver serial_txx9_reg = {
996 .owner = THIS_MODULE,
997 .driver_name = "serial_txx9",
998 .devfs_name = TXX9_TTY_DEVFS_NAME,
999 .dev_name = TXX9_TTY_NAME,
1000 .major = TXX9_TTY_MAJOR,
1001 .minor = TXX9_TTY_MINOR_START,
1002 .nr = UART_NR,
1003 .cons = SERIAL_TXX9_CONSOLE,
1004};
1005
1006int __init early_serial_txx9_setup(struct uart_port *port)
1007{
1008 if (port->line >= ARRAY_SIZE(serial_txx9_ports))
1009 return -ENODEV;
1010
1011 serial_txx9_ports[port->line].port = *port;
1012 serial_txx9_ports[port->line].port.ops = &serial_txx9_pops;
1013 serial_txx9_ports[port->line].port.flags |= UPF_BOOT_AUTOCONF;
1014 return 0;
1015}
1016
1017#ifdef ENABLE_SERIAL_TXX9_PCI
1018/**
1019 * serial_txx9_suspend_port - suspend one serial port
1020 * @line: serial line number
1021 * @level: the level of port suspension, as per uart_suspend_port
1022 *
1023 * Suspend one serial port.
1024 */
1025static void serial_txx9_suspend_port(int line)
1026{
1027 uart_suspend_port(&serial_txx9_reg, &serial_txx9_ports[line].port);
1028}
1029
1030/**
1031 * serial_txx9_resume_port - resume one serial port
1032 * @line: serial line number
1033 * @level: the level of port resumption, as per uart_resume_port
1034 *
1035 * Resume one serial port.
1036 */
1037static void serial_txx9_resume_port(int line)
1038{
1039 uart_resume_port(&serial_txx9_reg, &serial_txx9_ports[line].port);
1040}
1041
1042/*
1043 * Probe one serial board. Unfortunately, there is no rhyme nor reason
1044 * to the arrangement of serial ports on a PCI card.
1045 */
1046static int __devinit
1047pciserial_txx9_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
1048{
1049 struct uart_port port;
1050 int line;
1051 int rc;
1052
1053 rc = pci_enable_device(dev);
1054 if (rc)
1055 return rc;
1056
1057 memset(&port, 0, sizeof(port));
1058 port.ops = &serial_txx9_pops;
1059 port.flags |= UPF_BOOT_AUTOCONF; /* uart_ops.config_port will be called */
1060 port.flags |= UPF_TXX9_HAVE_CTS_LINE;
1061 port.uartclk = 66670000;
1062 port.irq = dev->irq;
1063 port.iotype = UPIO_PORT;
1064 port.iobase = pci_resource_start(dev, 1);
1065 line = uart_register_port(&serial_txx9_reg, &port);
1066 if (line < 0) {
1067 printk(KERN_WARNING "Couldn't register serial port %s: %d\n", pci_name(dev), line);
1068 }
1069 pci_set_drvdata(dev, (void *)(long)line);
1070
1071 return 0;
1072}
1073
1074static void __devexit pciserial_txx9_remove_one(struct pci_dev *dev)
1075{
1076 int line = (int)(long)pci_get_drvdata(dev);
1077
1078 pci_set_drvdata(dev, NULL);
1079
1080 if (line) {
1081 uart_unregister_port(&serial_txx9_reg, line);
1082 pci_disable_device(dev);
1083 }
1084}
1085
Pavel Machek0370aff2005-04-16 15:25:35 -07001086static int pciserial_txx9_suspend_one(struct pci_dev *dev, pm_message_t state)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001087{
1088 int line = (int)(long)pci_get_drvdata(dev);
1089
1090 if (line)
1091 serial_txx9_suspend_port(line);
1092 return 0;
1093}
1094
1095static int pciserial_txx9_resume_one(struct pci_dev *dev)
1096{
1097 int line = (int)(long)pci_get_drvdata(dev);
1098
1099 if (line)
1100 serial_txx9_resume_port(line);
1101 return 0;
1102}
1103
1104static struct pci_device_id serial_txx9_pci_tbl[] = {
1105 { PCI_VENDOR_ID_TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_TC86C001_MISC,
1106 PCI_ANY_ID, PCI_ANY_ID,
1107 0, 0, 0 },
1108 { 0, }
1109};
1110
1111static struct pci_driver serial_txx9_pci_driver = {
1112 .name = "serial_txx9",
1113 .probe = pciserial_txx9_init_one,
1114 .remove = __devexit_p(pciserial_txx9_remove_one),
1115 .suspend = pciserial_txx9_suspend_one,
1116 .resume = pciserial_txx9_resume_one,
1117 .id_table = serial_txx9_pci_tbl,
1118};
1119
1120MODULE_DEVICE_TABLE(pci, serial_txx9_pci_tbl);
1121#endif /* ENABLE_SERIAL_TXX9_PCI */
1122
1123static int __init serial_txx9_init(void)
1124{
1125 int ret;
1126
1127 printk(KERN_INFO "%s version %s\n", serial_name, serial_version);
1128
1129 ret = uart_register_driver(&serial_txx9_reg);
1130 if (ret >= 0) {
1131 serial_txx9_register_ports(&serial_txx9_reg);
1132
1133#ifdef ENABLE_SERIAL_TXX9_PCI
1134 ret = pci_module_init(&serial_txx9_pci_driver);
1135#endif
1136 }
1137 return ret;
1138}
1139
1140static void __exit serial_txx9_exit(void)
1141{
1142 int i;
1143
1144#ifdef ENABLE_SERIAL_TXX9_PCI
1145 pci_unregister_driver(&serial_txx9_pci_driver);
1146#endif
1147 for (i = 0; i < UART_NR; i++)
1148 uart_remove_one_port(&serial_txx9_reg, &serial_txx9_ports[i].port);
1149
1150 uart_unregister_driver(&serial_txx9_reg);
1151}
1152
1153module_init(serial_txx9_init);
1154module_exit(serial_txx9_exit);
1155
1156MODULE_LICENSE("GPL");
1157MODULE_DESCRIPTION("TX39/49 serial driver");
1158
1159MODULE_ALIAS_CHARDEV_MAJOR(TXX9_TTY_MAJOR);