Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1 | |
| 2 | # |
| 3 | # Network device configuration |
| 4 | # |
| 5 | |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 6 | menuconfig NETDEVICES |
Paolo 'Blaisorblade' Giarrusso | ce2d2ae | 2006-01-18 17:42:59 -0800 | [diff] [blame] | 7 | default y if UML |
Jan Engelhardt | e000982 | 2007-07-21 19:11:35 -0700 | [diff] [blame] | 8 | depends on NET |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 9 | bool "Network device support" |
| 10 | ---help--- |
| 11 | You can say N here if you don't intend to connect your Linux box to |
| 12 | any other computer at all. |
| 13 | |
| 14 | You'll have to say Y if your computer contains a network card that |
| 15 | you want to use under Linux. If you are going to run SLIP or PPP over |
| 16 | telephone line or null modem cable you need say Y here. Connecting |
| 17 | two machines with parallel ports using PLIP needs this, as well as |
| 18 | AX.25/KISS for sending Internet traffic over amateur radio links. |
| 19 | |
| 20 | See also "The Linux Network Administrator's Guide" by Olaf Kirch and |
| 21 | Terry Dawson. Available at <http://www.tldp.org/guides.html>. |
| 22 | |
| 23 | If unsure, say Y. |
| 24 | |
Randy Dunlap | 1618cb0 | 2006-09-25 23:11:21 -0700 | [diff] [blame] | 25 | # All the following symbols are dependent on NETDEVICES - do not repeat |
| 26 | # that for each of the symbols. |
| 27 | if NETDEVICES |
Randy Dunlap | cbcd2a4 | 2005-07-27 13:04:35 -0700 | [diff] [blame] | 28 | |
Peter P Waskiewicz Jr | f25f4e4 | 2007-07-06 13:36:20 -0700 | [diff] [blame] | 29 | config NETDEVICES_MULTIQUEUE |
| 30 | bool "Netdevice multiple hardware queue support" |
| 31 | ---help--- |
| 32 | Say Y here if you want to allow the network stack to use multiple |
| 33 | hardware TX queues on an ethernet device. |
| 34 | |
| 35 | Most people will say N here. |
| 36 | |
Jamal Hadi Salim | 253af42 | 2006-01-08 22:34:25 -0800 | [diff] [blame] | 37 | config IFB |
| 38 | tristate "Intermediate Functional Block support" |
| 39 | depends on NET_CLS_ACT |
| 40 | ---help--- |
Matt LaPlante | 3cb2fcc | 2006-11-30 05:22:59 +0100 | [diff] [blame] | 41 | This is an intermediate driver that allows sharing of |
Jamal Hadi Salim | 253af42 | 2006-01-08 22:34:25 -0800 | [diff] [blame] | 42 | resources. |
| 43 | To compile this driver as a module, choose M here: the module |
| 44 | will be called ifb. If you want to use more than one ifb |
| 45 | device at a time, you need to compile this driver as a module. |
| 46 | Instead of 'ifb', the devices will then be called 'ifb0', |
| 47 | 'ifb1' etc. |
| 48 | Look at the iproute2 documentation directory for usage etc |
| 49 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 50 | config DUMMY |
| 51 | tristate "Dummy net driver support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 52 | ---help--- |
| 53 | This is essentially a bit-bucket device (i.e. traffic you send to |
| 54 | this device is consigned into oblivion) with a configurable IP |
| 55 | address. It is most commonly used in order to make your currently |
| 56 | inactive SLIP address seem like a real address for local programs. |
| 57 | If you use SLIP or PPP, you might want to say Y here. Since this |
| 58 | thing often comes in handy, the default is Y. It won't enlarge your |
| 59 | kernel either. What a deal. Read about it in the Network |
| 60 | Administrator's Guide, available from |
| 61 | <http://www.tldp.org/docs.html#guide>. |
| 62 | |
| 63 | To compile this driver as a module, choose M here: the module |
| 64 | will be called dummy. If you want to use more than one dummy |
| 65 | device at a time, you need to compile this driver as a module. |
| 66 | Instead of 'dummy', the devices will then be called 'dummy0', |
| 67 | 'dummy1' etc. |
| 68 | |
| 69 | config BONDING |
| 70 | tristate "Bonding driver support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 71 | depends on INET |
| 72 | ---help--- |
| 73 | Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet |
| 74 | Channels together. This is called 'Etherchannel' by Cisco, |
| 75 | 'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux. |
| 76 | |
| 77 | The driver supports multiple bonding modes to allow for both high |
Jon Mason | 47c5143 | 2006-02-12 11:53:04 -0600 | [diff] [blame] | 78 | performance and high availability operation. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 79 | |
| 80 | Refer to <file:Documentation/networking/bonding.txt> for more |
| 81 | information. |
| 82 | |
| 83 | To compile this driver as a module, choose M here: the module |
| 84 | will be called bonding. |
| 85 | |
Patrick McHardy | b863ceb | 2007-07-14 18:55:06 -0700 | [diff] [blame] | 86 | config MACVLAN |
| 87 | tristate "MAC-VLAN support (EXPERIMENTAL)" |
| 88 | depends on EXPERIMENTAL |
| 89 | ---help--- |
| 90 | This allows one to create virtual interfaces that map packets to |
| 91 | or from specific MAC addresses to a particular interface. |
| 92 | |
| 93 | To compile this driver as a module, choose M here: the module |
| 94 | will be called macvlan. |
| 95 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 96 | config EQUALIZER |
| 97 | tristate "EQL (serial line load balancing) support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 98 | ---help--- |
| 99 | If you have two serial connections to some other computer (this |
| 100 | usually requires two modems and two telephone lines) and you use |
| 101 | SLIP (the protocol for sending Internet traffic over telephone |
| 102 | lines) or PPP (a better SLIP) on them, you can make them behave like |
| 103 | one double speed connection using this driver. Naturally, this has |
| 104 | to be supported at the other end as well, either with a similar EQL |
| 105 | Linux driver or with a Livingston Portmaster 2e. |
| 106 | |
| 107 | Say Y if you want this and read |
| 108 | <file:Documentation/networking/eql.txt>. You may also want to read |
| 109 | section 6.2 of the NET-3-HOWTO, available from |
| 110 | <http://www.tldp.org/docs.html#howto>. |
| 111 | |
| 112 | To compile this driver as a module, choose M here: the module |
| 113 | will be called eql. If unsure, say N. |
| 114 | |
| 115 | config TUN |
| 116 | tristate "Universal TUN/TAP device driver support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 117 | select CRC32 |
| 118 | ---help--- |
| 119 | TUN/TAP provides packet reception and transmission for user space |
| 120 | programs. It can be viewed as a simple Point-to-Point or Ethernet |
| 121 | device, which instead of receiving packets from a physical media, |
| 122 | receives them from user space program and instead of sending packets |
| 123 | via physical media writes them to the user space program. |
| 124 | |
| 125 | When a program opens /dev/net/tun, driver creates and registers |
| 126 | corresponding net device tunX or tapX. After a program closed above |
| 127 | devices, driver will automatically delete tunXX or tapXX device and |
| 128 | all routes corresponding to it. |
| 129 | |
| 130 | Please read <file:Documentation/networking/tuntap.txt> for more |
| 131 | information. |
| 132 | |
| 133 | To compile this driver as a module, choose M here: the module |
| 134 | will be called tun. |
| 135 | |
| 136 | If you don't know what to use this for, you don't need it. |
| 137 | |
Pavel Emelyanov | e314dbd | 2007-09-25 16:14:46 -0700 | [diff] [blame] | 138 | config VETH |
Rusty Russell | 6a9a025 | 2007-11-06 20:35:55 -0800 | [diff] [blame] | 139 | tristate "Virtual ethernet pair device" |
Pavel Emelyanov | e314dbd | 2007-09-25 16:14:46 -0700 | [diff] [blame] | 140 | ---help--- |
Rusty Russell | 6a9a025 | 2007-11-06 20:35:55 -0800 | [diff] [blame] | 141 | This device is a local ethernet tunnel. Devices are created in pairs. |
| 142 | When one end receives the packet it appears on its pair and vice |
| 143 | versa. |
Pavel Emelyanov | e314dbd | 2007-09-25 16:14:46 -0700 | [diff] [blame] | 144 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 145 | config NET_SB1000 |
| 146 | tristate "General Instruments Surfboard 1000" |
Randy Dunlap | cbcd2a4 | 2005-07-27 13:04:35 -0700 | [diff] [blame] | 147 | depends on PNP |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 148 | ---help--- |
| 149 | This is a driver for the General Instrument (also known as |
| 150 | NextLevel) SURFboard 1000 internal |
| 151 | cable modem. This is an ISA card which is used by a number of cable |
| 152 | TV companies to provide cable modem access. It's a one-way |
| 153 | downstream-only cable modem, meaning that your upstream net link is |
| 154 | provided by your regular phone modem. |
| 155 | |
| 156 | At present this driver only compiles as a module, so say M here if |
| 157 | you have this card. The module will be called sb1000. Then read |
| 158 | <file:Documentation/networking/README.sb1000> for information on how |
| 159 | to use this module, as it needs special ppp scripts for establishing |
| 160 | a connection. Further documentation and the necessary scripts can be |
| 161 | found at: |
| 162 | |
| 163 | <http://www.jacksonville.net/~fventuri/> |
| 164 | <http://home.adelphia.net/~siglercm/sb1000.html> |
| 165 | <http://linuxpower.cx/~cable/> |
| 166 | |
| 167 | If you don't have this card, of course say N. |
| 168 | |
Adrian Bunk | f65fd8f | 2006-01-05 22:45:41 -0800 | [diff] [blame] | 169 | source "drivers/net/arcnet/Kconfig" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 170 | |
Andy Fleming | 00db818 | 2005-07-30 19:31:23 -0400 | [diff] [blame] | 171 | source "drivers/net/phy/Kconfig" |
| 172 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 173 | # |
| 174 | # Ethernet |
| 175 | # |
| 176 | |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 177 | menuconfig NET_ETHERNET |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 178 | bool "Ethernet (10 or 100Mbit)" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 179 | depends on !UML |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 180 | ---help--- |
| 181 | Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common |
| 182 | type of Local Area Network (LAN) in universities and companies. |
| 183 | |
| 184 | Common varieties of Ethernet are: 10BASE-2 or Thinnet (10 Mbps over |
| 185 | coaxial cable, linking computers in a chain), 10BASE-T or twisted |
| 186 | pair (10 Mbps over twisted pair cable, linking computers to central |
| 187 | hubs), 10BASE-F (10 Mbps over optical fiber links, using hubs), |
| 188 | 100BASE-TX (100 Mbps over two twisted pair cables, using hubs), |
| 189 | 100BASE-T4 (100 Mbps over 4 standard voice-grade twisted pair |
| 190 | cables, using hubs), 100BASE-FX (100 Mbps over optical fiber links) |
| 191 | [the 100BASE varieties are also known as Fast Ethernet], and Gigabit |
| 192 | Ethernet (1 Gbps over optical fiber or short copper links). |
| 193 | |
| 194 | If your Linux machine will be connected to an Ethernet and you have |
| 195 | an Ethernet network interface card (NIC) installed in your computer, |
| 196 | say Y here and read the Ethernet-HOWTO, available from |
| 197 | <http://www.tldp.org/docs.html#howto>. You will then also have |
| 198 | to say Y to the driver for your particular NIC. |
| 199 | |
| 200 | Note that the answer to this question won't directly affect the |
| 201 | kernel: saying N will just cause the configurator to skip all |
| 202 | the questions about Ethernet network cards. If unsure, say N. |
| 203 | |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 204 | if NET_ETHERNET |
| 205 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 206 | config MII |
| 207 | tristate "Generic Media Independent Interface device support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 208 | help |
| 209 | Most ethernet controllers have MII transceiver either as an external |
| 210 | or internal device. It is safe to say Y or M here even if your |
| 211 | ethernet card lack MII. |
| 212 | |
Haavard Skinnemoen | 89e5785 | 2006-11-09 14:51:17 +0100 | [diff] [blame] | 213 | config MACB |
| 214 | tristate "Atmel MACB support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 215 | depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 |
frederic RODO | 6c36a70 | 2007-07-12 19:07:24 +0200 | [diff] [blame] | 216 | select PHYLIB |
Haavard Skinnemoen | 89e5785 | 2006-11-09 14:51:17 +0100 | [diff] [blame] | 217 | help |
| 218 | The Atmel MACB ethernet interface is found on many AT32 and AT91 |
| 219 | parts. Say Y to include support for the MACB chip. |
| 220 | |
| 221 | To compile this driver as a module, choose M here: the module |
| 222 | will be called macb. |
| 223 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 224 | source "drivers/net/arm/Kconfig" |
| 225 | |
Ben Dooks | 825a2ff | 2007-07-03 16:53:09 +0100 | [diff] [blame] | 226 | config AX88796 |
| 227 | tristate "ASIX AX88796 NE2000 clone support" |
Magnus Damm | 8687991 | 2007-11-08 16:31:05 +0900 | [diff] [blame] | 228 | depends on ARM || MIPS || SUPERH |
Ben Dooks | 825a2ff | 2007-07-03 16:53:09 +0100 | [diff] [blame] | 229 | select CRC32 |
| 230 | select MII |
| 231 | help |
| 232 | AX88796 driver, using platform bus to provide |
| 233 | chip detection and resources |
| 234 | |
Magnus Damm | 89e536a | 2007-09-28 22:42:16 -0700 | [diff] [blame] | 235 | config AX88796_93CX6 |
| 236 | bool "ASIX AX88796 external 93CX6 eeprom support" |
| 237 | depends on AX88796 |
| 238 | select EEPROM_93CX6 |
| 239 | help |
| 240 | Select this if your platform comes with an external 93CX6 eeprom. |
| 241 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 242 | config MACE |
| 243 | tristate "MACE (Power Mac ethernet) support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 244 | depends on PPC_PMAC && PPC32 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 245 | select CRC32 |
| 246 | help |
| 247 | Power Macintoshes and clones with Ethernet built-in on the |
| 248 | motherboard will usually use a MACE (Medium Access Control for |
| 249 | Ethernet) interface. Say Y to include support for the MACE chip. |
| 250 | |
| 251 | To compile this driver as a module, choose M here: the module |
| 252 | will be called mace. |
| 253 | |
| 254 | config MACE_AAUI_PORT |
| 255 | bool "Use AAUI port instead of TP by default" |
| 256 | depends on MACE |
| 257 | help |
| 258 | Some Apple machines (notably the Apple Network Server) which use the |
| 259 | MACE ethernet chip have an Apple AUI port (small 15-pin connector), |
| 260 | instead of an 8-pin RJ45 connector for twisted-pair ethernet. Say |
| 261 | Y here if you have such a machine. If unsure, say N. |
| 262 | The driver will default to AAUI on ANS anyway, and if you use it as |
| 263 | a module, you can provide the port_aaui=0|1 to force the driver. |
| 264 | |
| 265 | config BMAC |
| 266 | tristate "BMAC (G3 ethernet) support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 267 | depends on PPC_PMAC && PPC32 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 268 | select CRC32 |
| 269 | help |
| 270 | Say Y for support of BMAC Ethernet interfaces. These are used on G3 |
| 271 | computers. |
| 272 | |
| 273 | To compile this driver as a module, choose M here: the module |
| 274 | will be called bmac. |
| 275 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 276 | config ARIADNE |
| 277 | tristate "Ariadne support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 278 | depends on ZORRO |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 279 | help |
| 280 | If you have a Village Tronic Ariadne Ethernet adapter, say Y. |
| 281 | Otherwise, say N. |
| 282 | |
| 283 | To compile this driver as a module, choose M here: the module |
| 284 | will be called ariadne. |
| 285 | |
| 286 | config A2065 |
| 287 | tristate "A2065 support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 288 | depends on ZORRO |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 289 | select CRC32 |
| 290 | help |
| 291 | If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise, |
| 292 | say N. |
| 293 | |
| 294 | To compile this driver as a module, choose M here: the module |
| 295 | will be called a2065. |
| 296 | |
| 297 | config HYDRA |
| 298 | tristate "Hydra support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 299 | depends on ZORRO |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 300 | select CRC32 |
| 301 | help |
| 302 | If you have a Hydra Ethernet adapter, say Y. Otherwise, say N. |
| 303 | |
| 304 | To compile this driver as a module, choose M here: the module |
| 305 | will be called hydra. |
| 306 | |
| 307 | config ZORRO8390 |
| 308 | tristate "Zorro NS8390-based Ethernet support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 309 | depends on ZORRO |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 310 | select CRC32 |
| 311 | help |
| 312 | This driver is for Zorro Ethernet cards using an NS8390-compatible |
| 313 | chipset, like the Village Tronic Ariadne II and the Individual |
| 314 | Computers X-Surf Ethernet cards. If you have such a card, say Y. |
| 315 | Otherwise, say N. |
| 316 | |
| 317 | To compile this driver as a module, choose M here: the module |
| 318 | will be called zorro8390. |
| 319 | |
| 320 | config APNE |
| 321 | tristate "PCMCIA NE2000 support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 322 | depends on AMIGA_PCMCIA |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 323 | select CRC32 |
| 324 | help |
| 325 | If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise, |
| 326 | say N. |
| 327 | |
| 328 | To compile this driver as a module, choose M here: the module |
| 329 | will be called apne. |
| 330 | |
| 331 | config APOLLO_ELPLUS |
| 332 | tristate "Apollo 3c505 support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 333 | depends on APOLLO |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 334 | help |
| 335 | Say Y or M here if your Apollo has a 3Com 3c505 ISA Ethernet card. |
| 336 | If you don't have one made for Apollos, you can use one from a PC, |
| 337 | except that your Apollo won't be able to boot from it (because the |
| 338 | code in the ROM will be for a PC). |
| 339 | |
| 340 | config MAC8390 |
| 341 | bool "Macintosh NS 8390 based ethernet cards" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 342 | depends on MAC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 343 | select CRC32 |
| 344 | help |
| 345 | If you want to include a driver to support Nubus or LC-PDS |
| 346 | Ethernet cards using an NS8390 chipset or its equivalent, say Y |
| 347 | and read the Ethernet-HOWTO, available from |
| 348 | <http://www.tldp.org/docs.html#howto>. |
| 349 | |
| 350 | config MAC89x0 |
| 351 | tristate "Macintosh CS89x0 based ethernet cards" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 352 | depends on MAC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 353 | ---help--- |
| 354 | Support for CS89x0 chipset based Ethernet cards. If you have a |
| 355 | Nubus or LC-PDS network (Ethernet) card of this type, say Y and |
| 356 | read the Ethernet-HOWTO, available from |
| 357 | <http://www.tldp.org/docs.html#howto>. |
| 358 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 359 | To compile this driver as a module, choose M here. This module will |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 360 | be called mac89x0. |
| 361 | |
| 362 | config MACSONIC |
| 363 | tristate "Macintosh SONIC based ethernet (onboard, NuBus, LC, CS)" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 364 | depends on MAC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 365 | ---help--- |
| 366 | Support for NatSemi SONIC based Ethernet devices. This includes |
| 367 | the onboard Ethernet in many Quadras as well as some LC-PDS, |
| 368 | a few Nubus and all known Comm Slot Ethernet cards. If you have |
| 369 | one of these say Y and read the Ethernet-HOWTO, available from |
| 370 | <http://www.tldp.org/docs.html#howto>. |
| 371 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 372 | To compile this driver as a module, choose M here. This module will |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 373 | be called macsonic. |
| 374 | |
| 375 | config MACMACE |
Finn Thain | 8b6aaab | 2007-05-01 22:33:01 +0200 | [diff] [blame] | 376 | bool "Macintosh (AV) onboard MACE ethernet" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 377 | depends on MAC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 378 | select CRC32 |
| 379 | help |
| 380 | Support for the onboard AMD 79C940 MACE Ethernet controller used in |
| 381 | the 660AV and 840AV Macintosh. If you have one of these Macintoshes |
| 382 | say Y and read the Ethernet-HOWTO, available from |
| 383 | <http://www.tldp.org/docs.html#howto>. |
| 384 | |
| 385 | config MVME147_NET |
| 386 | tristate "MVME147 (Lance) Ethernet support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 387 | depends on MVME147 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 388 | select CRC32 |
| 389 | help |
| 390 | Support for the on-board Ethernet interface on the Motorola MVME147 |
| 391 | single-board computer. Say Y here to include the |
| 392 | driver for this chip in your kernel. |
| 393 | To compile this driver as a module, choose M here. |
| 394 | |
| 395 | config MVME16x_NET |
| 396 | tristate "MVME16x Ethernet support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 397 | depends on MVME16x |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 398 | help |
| 399 | This is the driver for the Ethernet interface on the Motorola |
| 400 | MVME162, 166, 167, 172 and 177 boards. Say Y here to include the |
| 401 | driver for this chip in your kernel. |
| 402 | To compile this driver as a module, choose M here. |
| 403 | |
| 404 | config BVME6000_NET |
| 405 | tristate "BVME6000 Ethernet support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 406 | depends on BVME6000 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 407 | help |
| 408 | This is the driver for the Ethernet interface on BVME4000 and |
| 409 | BVME6000 VME boards. Say Y here to include the driver for this chip |
| 410 | in your kernel. |
| 411 | To compile this driver as a module, choose M here. |
| 412 | |
| 413 | config ATARILANCE |
| 414 | tristate "Atari Lance support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 415 | depends on ATARI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 416 | help |
| 417 | Say Y to include support for several Atari Ethernet adapters based |
| 418 | on the AMD Lance chipset: RieblCard (with or without battery), or |
| 419 | PAMCard VME (also the version by Rhotron, with different addresses). |
| 420 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 421 | config SUN3LANCE |
| 422 | tristate "Sun3/Sun3x on-board LANCE support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 423 | depends on SUN3 || SUN3X |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 424 | help |
| 425 | Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80) |
| 426 | featured an AMD Lance 10Mbit Ethernet controller on board; say Y |
| 427 | here to compile in the Linux driver for this and enable Ethernet. |
| 428 | General Linux information on the Sun 3 and 3x series (now |
| 429 | discontinued) is at |
| 430 | <http://www.angelfire.com/ca2/tech68k/sun3.html>. |
| 431 | |
| 432 | If you're not building a kernel for a Sun 3, say N. |
| 433 | |
| 434 | config SUN3_82586 |
Al Viro | 9a48220 | 2005-08-25 06:24:56 +0100 | [diff] [blame] | 435 | bool "Sun3 on-board Intel 82586 support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 436 | depends on SUN3 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 437 | help |
| 438 | This driver enables support for the on-board Intel 82586 based |
| 439 | Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards. Note |
| 440 | that this driver does not support 82586-based adapters on additional |
| 441 | VME boards. |
| 442 | |
| 443 | config HPLANCE |
| 444 | bool "HP on-board LANCE support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 445 | depends on DIO |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 446 | select CRC32 |
| 447 | help |
| 448 | If you want to use the builtin "LANCE" Ethernet controller on an |
| 449 | HP300 machine, say Y here. |
| 450 | |
| 451 | config LASI_82596 |
| 452 | tristate "Lasi ethernet" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 453 | depends on GSC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 454 | help |
Matthew Wilcox | 6de187e | 2006-11-18 10:05:16 -0700 | [diff] [blame] | 455 | Say Y here to support the builtin Intel 82596 ethernet controller |
| 456 | found in Hewlett-Packard PA-RISC machines with 10Mbit ethernet. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 457 | |
Thomas Bogendoerfer | f2ec803 | 2007-06-28 00:49:06 +0200 | [diff] [blame] | 458 | config SNI_82596 |
| 459 | tristate "SNI RM ethernet" |
| 460 | depends on NET_ETHERNET && SNI_RM |
| 461 | help |
| 462 | Say Y here to support the on-board Intel 82596 ethernet controller |
| 463 | built into SNI RM machines. |
| 464 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 465 | config MIPS_JAZZ_SONIC |
| 466 | tristate "MIPS JAZZ onboard SONIC Ethernet support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 467 | depends on MACH_JAZZ |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 468 | help |
| 469 | This is the driver for the onboard card of MIPS Magnum 4000, |
| 470 | Acer PICA, Olivetti M700-10 and a few other identical OEM systems. |
| 471 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 472 | config MIPS_AU1X00_ENET |
| 473 | bool "MIPS AU1000 Ethernet support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 474 | depends on SOC_AU1X00 |
Herbert Valerio Riedel | 0638dec | 2006-06-01 09:41:04 +0200 | [diff] [blame] | 475 | select PHYLIB |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 476 | select CRC32 |
| 477 | help |
| 478 | If you have an Alchemy Semi AU1X00 based system |
| 479 | say Y. Otherwise, say N. |
| 480 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 481 | config SGI_IOC3_ETH |
| 482 | bool "SGI IOC3 Ethernet" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 483 | depends on PCI && SGI_IP27 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 484 | select CRC32 |
| 485 | select MII |
| 486 | help |
| 487 | If you have a network (Ethernet) card of this type, say Y and read |
| 488 | the Ethernet-HOWTO, available from |
| 489 | <http://www.tldp.org/docs.html#howto>. |
| 490 | |
Ralf Baechle | dcbf847 | 2005-10-10 14:51:27 +0100 | [diff] [blame] | 491 | config MIPS_SIM_NET |
Ralf Baechle | 1e2b980 | 2007-03-18 23:21:22 +0000 | [diff] [blame] | 492 | tristate "MIPS simulator Network device" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 493 | depends on MIPS_SIM |
Ralf Baechle | dcbf847 | 2005-10-10 14:51:27 +0100 | [diff] [blame] | 494 | help |
| 495 | The MIPSNET device is a simple Ethernet network device which is |
| 496 | emulated by the MIPS Simulator. |
| 497 | If you are not using a MIPSsim or are unsure, say N. |
| 498 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 499 | config SGI_O2MACE_ETH |
| 500 | tristate "SGI O2 MACE Fast Ethernet support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 501 | depends on SGI_IP32=y |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 502 | |
| 503 | config STNIC |
| 504 | tristate "National DP83902AV support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 505 | depends on SUPERH |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 506 | select CRC32 |
| 507 | help |
| 508 | Support for cards based on the National Semiconductor DP83902AV |
| 509 | ST-NIC Serial Network Interface Controller for Twisted Pair. This |
| 510 | is a 10Mbit/sec Ethernet controller. Product overview and specs at |
| 511 | <http://www.national.com/pf/DP/DP83902A.html>. |
| 512 | |
| 513 | If unsure, say N. |
| 514 | |
| 515 | config SUNLANCE |
| 516 | tristate "Sun LANCE support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 517 | depends on SBUS |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 518 | select CRC32 |
| 519 | help |
| 520 | This driver supports the "le" interface present on all 32-bit Sparc |
| 521 | systems, on some older Ultra systems and as an Sbus option. These |
| 522 | cards are based on the AMD Lance chipset, which is better known |
| 523 | via the NE2100 cards. |
| 524 | |
| 525 | To compile this driver as a module, choose M here: the module |
| 526 | will be called sunlance. |
| 527 | |
| 528 | config HAPPYMEAL |
| 529 | tristate "Sun Happy Meal 10/100baseT support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 530 | depends on SBUS || PCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 531 | select CRC32 |
| 532 | help |
| 533 | This driver supports the "hme" interface present on most Ultra |
| 534 | systems and as an option on older Sbus systems. This driver supports |
| 535 | both PCI and Sbus devices. This driver also supports the "qfe" quad |
| 536 | 100baseT device available in both PCI and Sbus configurations. |
| 537 | |
| 538 | To compile this driver as a module, choose M here: the module |
| 539 | will be called sunhme. |
| 540 | |
| 541 | config SUNBMAC |
| 542 | tristate "Sun BigMAC 10/100baseT support (EXPERIMENTAL)" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 543 | depends on SBUS && EXPERIMENTAL |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 544 | select CRC32 |
| 545 | help |
| 546 | This driver supports the "be" interface available as an Sbus option. |
| 547 | This is Sun's older 100baseT Ethernet device. |
| 548 | |
| 549 | To compile this driver as a module, choose M here: the module |
| 550 | will be called sunbmac. |
| 551 | |
| 552 | config SUNQE |
| 553 | tristate "Sun QuadEthernet support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 554 | depends on SBUS |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 555 | select CRC32 |
| 556 | help |
| 557 | This driver supports the "qe" 10baseT Ethernet device, available as |
| 558 | an Sbus option. Note that this is not the same as Quad FastEthernet |
| 559 | "qfe" which is supported by the Happy Meal driver instead. |
| 560 | |
| 561 | To compile this driver as a module, choose M here: the module |
| 562 | will be called sunqe. |
| 563 | |
| 564 | config SUNGEM |
| 565 | tristate "Sun GEM support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 566 | depends on PCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 567 | select CRC32 |
| 568 | help |
| 569 | Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0. See also |
| 570 | <http://www.sun.com/products-n-solutions/hardware/docs/pdf/806-3985-10.pdf>. |
| 571 | |
David S. Miller | 1f26dac | 2005-09-27 15:24:13 -0700 | [diff] [blame] | 572 | config CASSINI |
| 573 | tristate "Sun Cassini support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 574 | depends on PCI |
David S. Miller | 1f26dac | 2005-09-27 15:24:13 -0700 | [diff] [blame] | 575 | select CRC32 |
| 576 | help |
| 577 | Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also |
| 578 | <http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf> |
| 579 | |
David S. Miller | 4c521e4 | 2007-07-09 22:23:51 -0700 | [diff] [blame] | 580 | config SUNVNET |
| 581 | tristate "Sun Virtual Network support" |
| 582 | depends on SUN_LDOMS |
| 583 | help |
| 584 | Support for virtual network devices under Sun Logical Domains. |
| 585 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 586 | config NET_VENDOR_3COM |
| 587 | bool "3COM cards" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 588 | depends on ISA || EISA || MCA || PCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 589 | help |
| 590 | If you have a network (Ethernet) card belonging to this class, say Y |
| 591 | and read the Ethernet-HOWTO, available from |
| 592 | <http://www.tldp.org/docs.html#howto>. |
| 593 | |
| 594 | Note that the answer to this question doesn't directly affect the |
| 595 | kernel: saying N will just cause the configurator to skip all |
| 596 | the questions about 3COM cards. If you say Y, you will be asked for |
| 597 | your specific card in the following questions. |
| 598 | |
| 599 | config EL1 |
| 600 | tristate "3c501 \"EtherLink\" support" |
| 601 | depends on NET_VENDOR_3COM && ISA |
| 602 | ---help--- |
| 603 | If you have a network (Ethernet) card of this type, say Y and read |
| 604 | the Ethernet-HOWTO, available from |
| 605 | <http://www.tldp.org/docs.html#howto>. Also, consider buying a |
| 606 | new card, since the 3c501 is slow, broken, and obsolete: you will |
| 607 | have problems. Some people suggest to ping ("man ping") a nearby |
| 608 | machine every minute ("man cron") when using this card. |
| 609 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 610 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 611 | will be called 3c501. |
| 612 | |
| 613 | config EL2 |
| 614 | tristate "3c503 \"EtherLink II\" support" |
| 615 | depends on NET_VENDOR_3COM && ISA |
| 616 | select CRC32 |
| 617 | help |
| 618 | If you have a network (Ethernet) card of this type, say Y and read |
| 619 | the Ethernet-HOWTO, available from |
| 620 | <http://www.tldp.org/docs.html#howto>. |
| 621 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 622 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 623 | will be called 3c503. |
| 624 | |
| 625 | config ELPLUS |
| 626 | tristate "3c505 \"EtherLink Plus\" support" |
Al Viro | a553260 | 2005-05-04 05:39:42 +0100 | [diff] [blame] | 627 | depends on NET_VENDOR_3COM && ISA && ISA_DMA_API |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 628 | ---help--- |
| 629 | Information about this network (Ethernet) card can be found in |
| 630 | <file:Documentation/networking/3c505.txt>. If you have a card of |
| 631 | this type, say Y and read the Ethernet-HOWTO, available from |
| 632 | <http://www.tldp.org/docs.html#howto>. |
| 633 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 634 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 635 | will be called 3c505. |
| 636 | |
| 637 | config EL16 |
| 638 | tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)" |
| 639 | depends on NET_VENDOR_3COM && ISA && EXPERIMENTAL |
| 640 | help |
| 641 | If you have a network (Ethernet) card of this type, say Y and read |
| 642 | the Ethernet-HOWTO, available from |
| 643 | <http://www.tldp.org/docs.html#howto>. |
| 644 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 645 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 646 | will be called 3c507. |
| 647 | |
| 648 | config EL3 |
| 649 | tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support" |
| 650 | depends on NET_VENDOR_3COM && (ISA || EISA || MCA) |
| 651 | ---help--- |
| 652 | If you have a network (Ethernet) card belonging to the 3Com |
| 653 | EtherLinkIII series, say Y and read the Ethernet-HOWTO, available |
| 654 | from <http://www.tldp.org/docs.html#howto>. |
| 655 | |
| 656 | If your card is not working you may need to use the DOS |
| 657 | setup disk to disable Plug & Play mode, and to select the default |
| 658 | media type. |
| 659 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 660 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 661 | will be called 3c509. |
| 662 | |
| 663 | config 3C515 |
| 664 | tristate "3c515 ISA \"Fast EtherLink\"" |
Al Viro | a553260 | 2005-05-04 05:39:42 +0100 | [diff] [blame] | 665 | depends on NET_VENDOR_3COM && (ISA || EISA) && ISA_DMA_API |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 666 | help |
| 667 | If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet |
| 668 | network card, say Y and read the Ethernet-HOWTO, available from |
| 669 | <http://www.tldp.org/docs.html#howto>. |
| 670 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 671 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 672 | will be called 3c515. |
| 673 | |
| 674 | config ELMC |
| 675 | tristate "3c523 \"EtherLink/MC\" support" |
| 676 | depends on NET_VENDOR_3COM && MCA_LEGACY |
| 677 | help |
| 678 | If you have a network (Ethernet) card of this type, say Y and read |
| 679 | the Ethernet-HOWTO, available from |
| 680 | <http://www.tldp.org/docs.html#howto>. |
| 681 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 682 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 683 | will be called 3c523. |
| 684 | |
| 685 | config ELMC_II |
| 686 | tristate "3c527 \"EtherLink/MC 32\" support (EXPERIMENTAL)" |
| 687 | depends on NET_VENDOR_3COM && MCA && MCA_LEGACY |
| 688 | help |
| 689 | If you have a network (Ethernet) card of this type, say Y and read |
| 690 | the Ethernet-HOWTO, available from |
| 691 | <http://www.tldp.org/docs.html#howto>. |
| 692 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 693 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 694 | will be called 3c527. |
| 695 | |
| 696 | config VORTEX |
| 697 | tristate "3c590/3c900 series (592/595/597) \"Vortex/Boomerang\" support" |
| 698 | depends on NET_VENDOR_3COM && (PCI || EISA) |
| 699 | select MII |
| 700 | ---help--- |
Jon Mason | 47c5143 | 2006-02-12 11:53:04 -0600 | [diff] [blame] | 701 | This option enables driver support for a large number of 10Mbps and |
| 702 | 10/100Mbps EISA, PCI and PCMCIA 3Com network cards: |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 703 | |
| 704 | "Vortex" (Fast EtherLink 3c590/3c592/3c595/3c597) EISA and PCI |
| 705 | "Boomerang" (EtherLink XL 3c900 or 3c905) PCI |
| 706 | "Cyclone" (3c540/3c900/3c905/3c980/3c575/3c656) PCI and Cardbus |
| 707 | "Tornado" (3c905) PCI |
| 708 | "Hurricane" (3c555/3cSOHO) PCI |
| 709 | |
| 710 | If you have such a card, say Y and read the Ethernet-HOWTO, |
| 711 | available from <http://www.tldp.org/docs.html#howto>. More |
| 712 | specific information is in |
| 713 | <file:Documentation/networking/vortex.txt> and in the comments at |
| 714 | the beginning of <file:drivers/net/3c59x.c>. |
| 715 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 716 | To compile this support as a module, choose M here. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 717 | |
| 718 | config TYPHOON |
| 719 | tristate "3cr990 series \"Typhoon\" support" |
| 720 | depends on NET_VENDOR_3COM && PCI |
| 721 | select CRC32 |
| 722 | ---help--- |
| 723 | This option enables driver support for the 3cr990 series of cards: |
| 724 | |
| 725 | 3C990-TX, 3CR990-TX-95, 3CR990-TX-97, 3CR990-FX-95, 3CR990-FX-97, |
| 726 | 3CR990SVR, 3CR990SVR95, 3CR990SVR97, 3CR990-FX-95 Server, |
| 727 | 3CR990-FX-97 Server, 3C990B-TX-M, 3C990BSVR |
| 728 | |
| 729 | If you have a network (Ethernet) card of this type, say Y and read |
| 730 | the Ethernet-HOWTO, available from |
| 731 | <http://www.tldp.org/docs.html#howto>. |
| 732 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 733 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 734 | will be called typhoon. |
| 735 | |
| 736 | config LANCE |
| 737 | tristate "AMD LANCE and PCnet (AT1500 and NE2100) support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 738 | depends on ISA && ISA_DMA_API |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 739 | help |
| 740 | If you have a network (Ethernet) card of this type, say Y and read |
| 741 | the Ethernet-HOWTO, available from |
| 742 | <http://www.tldp.org/docs.html#howto>. Some LinkSys cards are |
| 743 | of this type. |
| 744 | |
| 745 | To compile this driver as a module, choose M here: the module |
| 746 | will be called lance. This is recommended. |
| 747 | |
| 748 | config NET_VENDOR_SMC |
| 749 | bool "Western Digital/SMC cards" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 750 | depends on ISA || MCA || EISA || MAC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 751 | help |
| 752 | If you have a network (Ethernet) card belonging to this class, say Y |
| 753 | and read the Ethernet-HOWTO, available from |
| 754 | <http://www.tldp.org/docs.html#howto>. |
| 755 | |
| 756 | Note that the answer to this question doesn't directly affect the |
| 757 | kernel: saying N will just cause the configurator to skip all |
| 758 | the questions about Western Digital cards. If you say Y, you will be |
| 759 | asked for your specific card in the following questions. |
| 760 | |
| 761 | config WD80x3 |
| 762 | tristate "WD80*3 support" |
| 763 | depends on NET_VENDOR_SMC && ISA |
| 764 | select CRC32 |
| 765 | help |
| 766 | If you have a network (Ethernet) card of this type, say Y and read |
| 767 | the Ethernet-HOWTO, available from |
| 768 | <http://www.tldp.org/docs.html#howto>. |
| 769 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 770 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 771 | will be called wd. |
| 772 | |
| 773 | config ULTRAMCA |
| 774 | tristate "SMC Ultra MCA support" |
| 775 | depends on NET_VENDOR_SMC && MCA |
| 776 | select CRC32 |
| 777 | help |
| 778 | If you have a network (Ethernet) card of this type and are running |
| 779 | an MCA based system (PS/2), say Y and read the Ethernet-HOWTO, |
| 780 | available from <http://www.tldp.org/docs.html#howto>. |
| 781 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 782 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 783 | will be called smc-mca. |
| 784 | |
| 785 | config ULTRA |
| 786 | tristate "SMC Ultra support" |
| 787 | depends on NET_VENDOR_SMC && ISA |
| 788 | select CRC32 |
| 789 | ---help--- |
| 790 | If you have a network (Ethernet) card of this type, say Y and read |
| 791 | the Ethernet-HOWTO, available from |
| 792 | <http://www.tldp.org/docs.html#howto>. |
| 793 | |
| 794 | Important: There have been many reports that, with some motherboards |
| 795 | mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible, |
| 796 | such as some BusLogic models) causes corruption problems with many |
| 797 | operating systems. The Linux smc-ultra driver has a work-around for |
| 798 | this but keep it in mind if you have such a SCSI card and have |
| 799 | problems. |
| 800 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 801 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 802 | will be called smc-ultra. |
| 803 | |
| 804 | config ULTRA32 |
| 805 | tristate "SMC Ultra32 EISA support" |
| 806 | depends on NET_VENDOR_SMC && EISA |
| 807 | select CRC32 |
| 808 | help |
| 809 | If you have a network (Ethernet) card of this type, say Y and read |
| 810 | the Ethernet-HOWTO, available from |
| 811 | <http://www.tldp.org/docs.html#howto>. |
| 812 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 813 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 814 | will be called smc-ultra32. |
| 815 | |
Bryan Wu | e190d6b | 2007-07-17 14:43:44 +0800 | [diff] [blame] | 816 | config BFIN_MAC |
| 817 | tristate "Blackfin 536/537 on-chip mac support" |
| 818 | depends on NET_ETHERNET && (BF537 || BF536) && (!BF537_PORT_H) |
| 819 | select CRC32 |
Bryan Wu | eeb70af | 2007-09-19 23:37:41 +0800 | [diff] [blame] | 820 | select MII |
| 821 | select PHYLIB |
Bryan Wu | e190d6b | 2007-07-17 14:43:44 +0800 | [diff] [blame] | 822 | select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE |
| 823 | help |
| 824 | This is the driver for blackfin on-chip mac device. Say Y if you want it |
| 825 | compiled into the kernel. This driver is also available as a module |
| 826 | ( = code which can be inserted in and removed from the running kernel |
| 827 | whenever you want). The module will be called bfin_mac. |
| 828 | |
| 829 | config BFIN_MAC_USE_L1 |
| 830 | bool "Use L1 memory for rx/tx packets" |
| 831 | depends on BFIN_MAC && BF537 |
| 832 | default y |
| 833 | help |
Matt LaPlante | 01dd2fb | 2007-10-20 01:34:40 +0200 | [diff] [blame] | 834 | To get maximum network performance, you should use L1 memory as rx/tx buffers. |
Bryan Wu | e190d6b | 2007-07-17 14:43:44 +0800 | [diff] [blame] | 835 | Say N here if you want to reserve L1 memory for other uses. |
| 836 | |
| 837 | config BFIN_TX_DESC_NUM |
| 838 | int "Number of transmit buffer packets" |
| 839 | depends on BFIN_MAC |
| 840 | range 6 10 if BFIN_MAC_USE_L1 |
| 841 | range 10 100 |
| 842 | default "10" |
| 843 | help |
| 844 | Set the number of buffer packets used in driver. |
| 845 | |
| 846 | config BFIN_RX_DESC_NUM |
| 847 | int "Number of receive buffer packets" |
| 848 | depends on BFIN_MAC |
| 849 | range 20 100 if BFIN_MAC_USE_L1 |
| 850 | range 20 800 |
| 851 | default "20" |
| 852 | help |
| 853 | Set the number of buffer packets used in driver. |
| 854 | |
| 855 | config BFIN_MAC_RMII |
| 856 | bool "RMII PHY Interface (EXPERIMENTAL)" |
| 857 | depends on BFIN_MAC && EXPERIMENTAL |
| 858 | default n |
| 859 | help |
| 860 | Use Reduced PHY MII Interface |
| 861 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 862 | config SMC9194 |
| 863 | tristate "SMC 9194 support" |
| 864 | depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN) |
| 865 | select CRC32 |
| 866 | ---help--- |
| 867 | This is support for the SMC9xxx based Ethernet cards. Choose this |
| 868 | option if you have a DELL laptop with the docking station, or |
| 869 | another SMC9192/9194 based chipset. Say Y if you want it compiled |
| 870 | into the kernel, and read the file |
| 871 | <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO, |
| 872 | available from <http://www.tldp.org/docs.html#howto>. |
| 873 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 874 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 875 | will be called smc9194. |
| 876 | |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 877 | config SMC91X |
| 878 | tristate "SMC 91C9x/91C1xxx support" |
| 879 | select CRC32 |
| 880 | select MII |
Mike Frysinger | 95af9fe | 2007-11-23 17:55:50 +0800 | [diff] [blame] | 881 | depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00 || BLACKFIN |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 882 | help |
| 883 | This is a driver for SMC's 91x series of Ethernet chipsets, |
| 884 | including the SMC91C94 and the SMC91C111. Say Y if you want it |
| 885 | compiled into the kernel, and read the file |
| 886 | <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO, |
| 887 | available from <http://www.linuxdoc.org/docs.html#howto>. |
| 888 | |
| 889 | This driver is also available as a module ( = code which can be |
| 890 | inserted in and removed from the running kernel whenever you want). |
| 891 | The module will be called smc91x. If you want to compile it as a |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 892 | module, say M here and read <file:Documentation/kbuild/modules.txt>. |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 893 | |
Sascha Hauer | 92aa674 | 2006-06-22 07:11:13 +0200 | [diff] [blame] | 894 | config NET_NETX |
| 895 | tristate "NetX Ethernet support" |
| 896 | select MII |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 897 | depends on ARCH_NETX |
Sascha Hauer | 92aa674 | 2006-06-22 07:11:13 +0200 | [diff] [blame] | 898 | help |
| 899 | This is support for the Hilscher netX builtin Ethernet ports |
| 900 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 901 | To compile this driver as a module, choose M here. The module |
Sascha Hauer | 92aa674 | 2006-06-22 07:11:13 +0200 | [diff] [blame] | 902 | will be called netx-eth. |
| 903 | |
Sascha Hauer | a136527 | 2005-05-05 15:14:15 -0700 | [diff] [blame] | 904 | config DM9000 |
| 905 | tristate "DM9000 support" |
Alex Landau | f40d24d | 2007-07-12 12:11:48 +0800 | [diff] [blame] | 906 | depends on ARM || BLACKFIN || MIPS |
Sascha Hauer | a136527 | 2005-05-05 15:14:15 -0700 | [diff] [blame] | 907 | select CRC32 |
| 908 | select MII |
| 909 | ---help--- |
| 910 | Support for DM9000 chipset. |
| 911 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 912 | To compile this driver as a module, choose M here. The module |
| 913 | will be called dm9000. |
Sascha Hauer | a136527 | 2005-05-05 15:14:15 -0700 | [diff] [blame] | 914 | |
Dustin McIntire | 0a0c72c | 2006-04-19 20:24:51 -0700 | [diff] [blame] | 915 | config SMC911X |
| 916 | tristate "SMSC LAN911[5678] support" |
| 917 | select CRC32 |
| 918 | select MII |
Paul Mundt | 0313d98 | 2007-11-28 18:24:59 +0900 | [diff] [blame] | 919 | depends on ARCH_PXA || SH_MAGIC_PANEL_R2 |
Dustin McIntire | 0a0c72c | 2006-04-19 20:24:51 -0700 | [diff] [blame] | 920 | help |
| 921 | This is a driver for SMSC's LAN911x series of Ethernet chipsets |
| 922 | including the new LAN9115, LAN9116, LAN9117, and LAN9118. |
| 923 | Say Y if you want it compiled into the kernel, |
| 924 | and read the Ethernet-HOWTO, available from |
| 925 | <http://www.linuxdoc.org/docs.html#howto>. |
| 926 | |
| 927 | This driver is also available as a module. The module will be |
| 928 | called smc911x. If you want to compile it as a module, say M |
Alexander E. Patrakov | 39f5fb3 | 2007-03-16 18:28:43 +0500 | [diff] [blame] | 929 | here and read <file:Documentation/kbuild/modules.txt> |
Dustin McIntire | 0a0c72c | 2006-04-19 20:24:51 -0700 | [diff] [blame] | 930 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 931 | config NET_VENDOR_RACAL |
| 932 | bool "Racal-Interlan (Micom) NI cards" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 933 | depends on ISA |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 934 | help |
| 935 | If you have a network (Ethernet) card belonging to this class, such |
| 936 | as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO, |
| 937 | available from <http://www.tldp.org/docs.html#howto>. |
| 938 | |
| 939 | Note that the answer to this question doesn't directly affect the |
| 940 | kernel: saying N will just cause the configurator to skip all |
| 941 | the questions about NI cards. If you say Y, you will be asked for |
| 942 | your specific card in the following questions. |
| 943 | |
| 944 | config NI5010 |
| 945 | tristate "NI5010 support (EXPERIMENTAL)" |
| 946 | depends on NET_VENDOR_RACAL && ISA && EXPERIMENTAL && BROKEN_ON_SMP |
| 947 | ---help--- |
| 948 | If you have a network (Ethernet) card of this type, say Y and read |
| 949 | the Ethernet-HOWTO, available from |
| 950 | <http://www.tldp.org/docs.html#howto>. Note that this is still |
| 951 | experimental code. |
| 952 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 953 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 954 | will be called ni5010. |
| 955 | |
| 956 | config NI52 |
| 957 | tristate "NI5210 support" |
| 958 | depends on NET_VENDOR_RACAL && ISA |
| 959 | help |
| 960 | If you have a network (Ethernet) card of this type, say Y and read |
| 961 | the Ethernet-HOWTO, available from |
| 962 | <http://www.tldp.org/docs.html#howto>. |
| 963 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 964 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 965 | will be called ni52. |
| 966 | |
| 967 | config NI65 |
| 968 | tristate "NI6510 support" |
Al Viro | a553260 | 2005-05-04 05:39:42 +0100 | [diff] [blame] | 969 | depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 970 | help |
| 971 | If you have a network (Ethernet) card of this type, say Y and read |
| 972 | the Ethernet-HOWTO, available from |
| 973 | <http://www.tldp.org/docs.html#howto>. |
| 974 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 975 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 976 | will be called ni65. |
| 977 | |
| 978 | source "drivers/net/tulip/Kconfig" |
| 979 | |
| 980 | config AT1700 |
| 981 | tristate "AT1700/1720 support (EXPERIMENTAL)" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 982 | depends on (ISA || MCA_LEGACY) && EXPERIMENTAL |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 983 | select CRC32 |
| 984 | ---help--- |
| 985 | If you have a network (Ethernet) card of this type, say Y and read |
| 986 | the Ethernet-HOWTO, available from |
| 987 | <http://www.tldp.org/docs.html#howto>. |
| 988 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 989 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 990 | will be called at1700. |
| 991 | |
| 992 | config DEPCA |
| 993 | tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 994 | depends on ISA || EISA || MCA |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 995 | select CRC32 |
| 996 | ---help--- |
| 997 | If you have a network (Ethernet) card of this type, say Y and read |
| 998 | the Ethernet-HOWTO, available from |
| 999 | <http://www.tldp.org/docs.html#howto> as well as |
| 1000 | <file:drivers/net/depca.c>. |
| 1001 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1002 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1003 | will be called depca. |
| 1004 | |
| 1005 | config HP100 |
| 1006 | tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 1007 | depends on ISA || EISA || PCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1008 | help |
| 1009 | If you have a network (Ethernet) card of this type, say Y and read |
| 1010 | the Ethernet-HOWTO, available from |
| 1011 | <http://www.tldp.org/docs.html#howto>. |
| 1012 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1013 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1014 | will be called hp100. |
| 1015 | |
| 1016 | config NET_ISA |
| 1017 | bool "Other ISA cards" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 1018 | depends on ISA |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1019 | ---help--- |
| 1020 | If your network (Ethernet) card hasn't been mentioned yet and its |
| 1021 | bus system (that's the way the cards talks to the other components |
| 1022 | of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y. |
| 1023 | Make sure you know the name of your card. Read the Ethernet-HOWTO, |
| 1024 | available from <http://www.tldp.org/docs.html#howto>. |
| 1025 | |
| 1026 | If unsure, say Y. |
| 1027 | |
| 1028 | Note that the answer to this question doesn't directly affect the |
| 1029 | kernel: saying N will just cause the configurator to skip all |
| 1030 | the remaining ISA network card questions. If you say Y, you will be |
| 1031 | asked for your specific card in the following questions. |
| 1032 | |
| 1033 | config E2100 |
| 1034 | tristate "Cabletron E21xx support" |
| 1035 | depends on NET_ISA |
| 1036 | select CRC32 |
| 1037 | help |
| 1038 | If you have a network (Ethernet) card of this type, say Y and read |
| 1039 | the Ethernet-HOWTO, available from |
| 1040 | <http://www.tldp.org/docs.html#howto>. |
| 1041 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1042 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1043 | will be called e2100. |
| 1044 | |
| 1045 | config EWRK3 |
| 1046 | tristate "EtherWORKS 3 (DE203, DE204, DE205) support" |
| 1047 | depends on NET_ISA |
| 1048 | select CRC32 |
| 1049 | ---help--- |
| 1050 | This driver supports the DE203, DE204 and DE205 network (Ethernet) |
| 1051 | cards. If this is for you, say Y and read |
| 1052 | <file:Documentation/networking/ewrk3.txt> in the kernel source as |
| 1053 | well as the Ethernet-HOWTO, available from |
| 1054 | <http://www.tldp.org/docs.html#howto>. |
| 1055 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1056 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1057 | will be called ewrk3. |
| 1058 | |
| 1059 | config EEXPRESS |
| 1060 | tristate "EtherExpress 16 support" |
| 1061 | depends on NET_ISA |
| 1062 | ---help--- |
| 1063 | If you have an EtherExpress16 network (Ethernet) card, say Y and |
| 1064 | read the Ethernet-HOWTO, available from |
| 1065 | <http://www.tldp.org/docs.html#howto>. Note that the Intel |
| 1066 | EtherExpress16 card used to be regarded as a very poor choice |
| 1067 | because the driver was very unreliable. We now have a new driver |
| 1068 | that should do better. |
| 1069 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1070 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1071 | will be called eexpress. |
| 1072 | |
| 1073 | config EEXPRESS_PRO |
| 1074 | tristate "EtherExpressPro support/EtherExpress 10 (i82595) support" |
| 1075 | depends on NET_ISA |
| 1076 | ---help--- |
| 1077 | If you have a network (Ethernet) card of this type, say Y. This |
Jon Mason | 47c5143 | 2006-02-12 11:53:04 -0600 | [diff] [blame] | 1078 | driver supports Intel i82595{FX,TX} based boards. Note however |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1079 | that the EtherExpress PRO/100 Ethernet card has its own separate |
| 1080 | driver. Please read the Ethernet-HOWTO, available from |
| 1081 | <http://www.tldp.org/docs.html#howto>. |
| 1082 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1083 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1084 | will be called eepro. |
| 1085 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1086 | config HPLAN_PLUS |
| 1087 | tristate "HP PCLAN+ (27247B and 27252A) support" |
| 1088 | depends on NET_ISA |
| 1089 | select CRC32 |
| 1090 | help |
| 1091 | If you have a network (Ethernet) card of this type, say Y and read |
| 1092 | the Ethernet-HOWTO, available from |
| 1093 | <http://www.tldp.org/docs.html#howto>. |
| 1094 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1095 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1096 | will be called hp-plus. |
| 1097 | |
| 1098 | config HPLAN |
| 1099 | tristate "HP PCLAN (27245 and other 27xxx series) support" |
| 1100 | depends on NET_ISA |
| 1101 | select CRC32 |
| 1102 | help |
| 1103 | If you have a network (Ethernet) card of this type, say Y and read |
| 1104 | the Ethernet-HOWTO, available from |
| 1105 | <http://www.tldp.org/docs.html#howto>. |
| 1106 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1107 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1108 | will be called hp. |
| 1109 | |
| 1110 | config LP486E |
| 1111 | tristate "LP486E on board Ethernet" |
| 1112 | depends on NET_ISA |
| 1113 | help |
| 1114 | Say Y here to support the 82596-based on-board Ethernet controller |
| 1115 | for the Panther motherboard, which is one of the two shipped in the |
| 1116 | Intel Professional Workstation. |
| 1117 | |
| 1118 | config ETH16I |
| 1119 | tristate "ICL EtherTeam 16i/32 support" |
| 1120 | depends on NET_ISA |
| 1121 | help |
| 1122 | If you have a network (Ethernet) card of this type, say Y and read |
| 1123 | the Ethernet-HOWTO, available from |
| 1124 | <http://www.tldp.org/docs.html#howto>. |
| 1125 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1126 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1127 | will be called eth16i. |
| 1128 | |
| 1129 | config NE2000 |
| 1130 | tristate "NE2000/NE1000 support" |
Atsushi Nemoto | 57e386c | 2007-05-01 00:27:58 +0900 | [diff] [blame] | 1131 | depends on NET_ISA || (Q40 && m) || M32R || TOSHIBA_RBTX4927 || TOSHIBA_RBTX4938 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1132 | select CRC32 |
| 1133 | ---help--- |
| 1134 | If you have a network (Ethernet) card of this type, say Y and read |
| 1135 | the Ethernet-HOWTO, available from |
| 1136 | <http://www.tldp.org/docs.html#howto>. Many Ethernet cards |
| 1137 | without a specific driver are compatible with NE2000. |
| 1138 | |
| 1139 | If you have a PCI NE2000 card however, say N here and Y to "PCI |
Jesper Juhl | 28beaf6 | 2006-03-08 00:06:31 -0800 | [diff] [blame] | 1140 | NE2000 and clone support" under "EISA, VLB, PCI and on board |
| 1141 | controllers" below. If you have a NE2000 card and are running on |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1142 | an MCA system (a bus system used on some IBM PS/2 computers and |
| 1143 | laptops), say N here and Y to "NE/2 (ne2000 MCA version) support", |
| 1144 | below. |
| 1145 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1146 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1147 | will be called ne. |
| 1148 | |
| 1149 | config ZNET |
| 1150 | tristate "Zenith Z-Note support (EXPERIMENTAL)" |
Al Viro | a553260 | 2005-05-04 05:39:42 +0100 | [diff] [blame] | 1151 | depends on NET_ISA && EXPERIMENTAL && ISA_DMA_API |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1152 | help |
| 1153 | The Zenith Z-Note notebook computer has a built-in network |
| 1154 | (Ethernet) card, and this is the Linux driver for it. Note that the |
| 1155 | IBM Thinkpad 300 is compatible with the Z-Note and is also supported |
| 1156 | by this driver. Read the Ethernet-HOWTO, available from |
| 1157 | <http://www.tldp.org/docs.html#howto>. |
| 1158 | |
| 1159 | config SEEQ8005 |
| 1160 | tristate "SEEQ8005 support (EXPERIMENTAL)" |
| 1161 | depends on NET_ISA && EXPERIMENTAL |
| 1162 | help |
| 1163 | This is a driver for the SEEQ 8005 network (Ethernet) card. If this |
| 1164 | is for you, read the Ethernet-HOWTO, available from |
| 1165 | <http://www.tldp.org/docs.html#howto>. |
| 1166 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1167 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1168 | will be called seeq8005. |
| 1169 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1170 | config NE2_MCA |
| 1171 | tristate "NE/2 (ne2000 MCA version) support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 1172 | depends on MCA_LEGACY |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1173 | select CRC32 |
| 1174 | help |
| 1175 | If you have a network (Ethernet) card of this type, say Y and read |
| 1176 | the Ethernet-HOWTO, available from |
| 1177 | <http://www.tldp.org/docs.html#howto>. |
| 1178 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1179 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1180 | will be called ne2. |
| 1181 | |
| 1182 | config IBMLANA |
| 1183 | tristate "IBM LAN Adapter/A support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 1184 | depends on MCA && MCA_LEGACY |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1185 | ---help--- |
| 1186 | This is a Micro Channel Ethernet adapter. You need to set |
| 1187 | CONFIG_MCA to use this driver. It is both available as an in-kernel |
| 1188 | driver and as a module. |
| 1189 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1190 | To compile this driver as a module, choose M here. The only |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1191 | currently supported card is the IBM LAN Adapter/A for Ethernet. It |
| 1192 | will both support 16K and 32K memory windows, however a 32K window |
| 1193 | gives a better security against packet losses. Usage of multiple |
| 1194 | boards with this driver should be possible, but has not been tested |
| 1195 | up to now due to lack of hardware. |
| 1196 | |
| 1197 | config IBMVETH |
| 1198 | tristate "IBM LAN Virtual Ethernet support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 1199 | depends on PPC_PSERIES |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1200 | ---help--- |
| 1201 | This driver supports virtual ethernet adapters on newer IBM iSeries |
| 1202 | and pSeries systems. |
| 1203 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1204 | To compile this driver as a module, choose M here. The module will |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1205 | be called ibmveth. |
| 1206 | |
David Gibson | 1d3bb99 | 2007-08-23 13:56:01 +1000 | [diff] [blame] | 1207 | source "drivers/net/ibm_emac/Kconfig" |
| 1208 | source "drivers/net/ibm_newemac/Kconfig" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1209 | |
| 1210 | config NET_PCI |
| 1211 | bool "EISA, VLB, PCI and on board controllers" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 1212 | depends on ISA || EISA || PCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1213 | help |
| 1214 | This is another class of network cards which attach directly to the |
| 1215 | bus. If you have one of those, say Y and read the Ethernet-HOWTO, |
| 1216 | available from <http://www.tldp.org/docs.html#howto>. |
| 1217 | |
| 1218 | Note that the answer to this question doesn't directly affect the |
| 1219 | kernel: saying N will just cause the configurator to skip all |
| 1220 | the questions about this class of network cards. If you say Y, you |
| 1221 | will be asked for your specific card in the following questions. If |
| 1222 | you are unsure, say Y. |
| 1223 | |
| 1224 | config PCNET32 |
| 1225 | tristate "AMD PCnet32 PCI support" |
| 1226 | depends on NET_PCI && PCI |
| 1227 | select CRC32 |
| 1228 | select MII |
| 1229 | help |
| 1230 | If you have a PCnet32 or PCnetPCI based network (Ethernet) card, |
| 1231 | answer Y here and read the Ethernet-HOWTO, available from |
| 1232 | <http://www.tldp.org/docs.html#howto>. |
| 1233 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1234 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1235 | will be called pcnet32. |
| 1236 | |
Don Fry | 7de745e | 2006-09-13 10:16:53 -0700 | [diff] [blame] | 1237 | config PCNET32_NAPI |
pcnet32@verizon.net | 659dd83 | 2007-02-16 10:09:57 -0600 | [diff] [blame] | 1238 | bool "Use RX polling (NAPI)" |
| 1239 | depends on PCNET32 |
Don Fry | 7de745e | 2006-09-13 10:16:53 -0700 | [diff] [blame] | 1240 | help |
| 1241 | NAPI is a new driver API designed to reduce CPU and interrupt load |
| 1242 | when the driver is receiving lots of packets from the card. It is |
| 1243 | still somewhat experimental and thus not yet enabled by default. |
| 1244 | |
| 1245 | If your estimated Rx load is 10kpps or more, or if the card will be |
| 1246 | deployed on potentially unfriendly networks (e.g. in a firewall), |
| 1247 | then say Y here. |
| 1248 | |
Don Fry | 7de745e | 2006-09-13 10:16:53 -0700 | [diff] [blame] | 1249 | If in doubt, say N. |
| 1250 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1251 | config AMD8111_ETH |
| 1252 | tristate "AMD 8111 (new PCI lance) support" |
| 1253 | depends on NET_PCI && PCI |
| 1254 | select CRC32 |
| 1255 | select MII |
| 1256 | help |
| 1257 | If you have an AMD 8111-based PCI lance ethernet card, |
| 1258 | answer Y here and read the Ethernet-HOWTO, available from |
| 1259 | <http://www.tldp.org/docs.html#howto>. |
| 1260 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1261 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1262 | will be called amd8111e. |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 1263 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1264 | config AMD8111E_NAPI |
Randy Dunlap | bf45abe | 2007-10-18 17:16:20 -0700 | [diff] [blame] | 1265 | bool "Use RX polling (NAPI)" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1266 | depends on AMD8111_ETH |
| 1267 | help |
| 1268 | NAPI is a new driver API designed to reduce CPU and interrupt load |
| 1269 | when the driver is receiving lots of packets from the card. It is |
| 1270 | still somewhat experimental and thus not yet enabled by default. |
| 1271 | |
| 1272 | If your estimated Rx load is 10kpps or more, or if the card will be |
| 1273 | deployed on potentially unfriendly networks (e.g. in a firewall), |
| 1274 | then say Y here. |
| 1275 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1276 | If in doubt, say N. |
| 1277 | |
| 1278 | config ADAPTEC_STARFIRE |
| 1279 | tristate "Adaptec Starfire/DuraLAN support" |
| 1280 | depends on NET_PCI && PCI |
| 1281 | select CRC32 |
| 1282 | select MII |
| 1283 | help |
| 1284 | Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network |
| 1285 | adapter. The DuraLAN chip is used on the 64 bit PCI boards from |
| 1286 | Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip |
| 1287 | driver. |
| 1288 | |
| 1289 | To compile this driver as a module, choose M here: the module |
| 1290 | will be called starfire. This is recommended. |
| 1291 | |
| 1292 | config ADAPTEC_STARFIRE_NAPI |
| 1293 | bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" |
| 1294 | depends on ADAPTEC_STARFIRE && EXPERIMENTAL |
| 1295 | help |
| 1296 | NAPI is a new driver API designed to reduce CPU and interrupt load |
| 1297 | when the driver is receiving lots of packets from the card. It is |
| 1298 | still somewhat experimental and thus not yet enabled by default. |
| 1299 | |
| 1300 | If your estimated Rx load is 10kpps or more, or if the card will be |
| 1301 | deployed on potentially unfriendly networks (e.g. in a firewall), |
| 1302 | then say Y here. |
| 1303 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1304 | If in doubt, say N. |
| 1305 | |
| 1306 | config AC3200 |
| 1307 | tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)" |
| 1308 | depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL |
| 1309 | select CRC32 |
| 1310 | help |
| 1311 | If you have a network (Ethernet) card of this type, say Y and read |
| 1312 | the Ethernet-HOWTO, available from |
| 1313 | <http://www.tldp.org/docs.html#howto>. |
| 1314 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1315 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1316 | will be called ac3200. |
| 1317 | |
| 1318 | config APRICOT |
| 1319 | tristate "Apricot Xen-II on board Ethernet" |
| 1320 | depends on NET_PCI && ISA |
| 1321 | help |
| 1322 | If you have a network (Ethernet) controller of this type, say Y and |
| 1323 | read the Ethernet-HOWTO, available from |
| 1324 | <http://www.tldp.org/docs.html#howto>. |
| 1325 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1326 | To compile this driver as a module, choose M here. The module |
| 1327 | will be called apricot. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1328 | |
| 1329 | config B44 |
Michael Buesch | 753f492 | 2007-09-19 14:20:30 -0700 | [diff] [blame] | 1330 | tristate "Broadcom 440x/47xx ethernet support" |
| 1331 | depends on SSB_POSSIBLE |
| 1332 | select SSB |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1333 | select MII |
| 1334 | help |
Michael Buesch | 753f492 | 2007-09-19 14:20:30 -0700 | [diff] [blame] | 1335 | If you have a network (Ethernet) controller of this type, say Y |
| 1336 | or M and read the Ethernet-HOWTO, available from |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1337 | <http://www.tldp.org/docs.html#howto>. |
| 1338 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1339 | To compile this driver as a module, choose M here. The module |
| 1340 | will be called b44. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1341 | |
Michael Buesch | 753f492 | 2007-09-19 14:20:30 -0700 | [diff] [blame] | 1342 | # Auto-select SSB PCI-HOST support, if possible |
| 1343 | config B44_PCI_AUTOSELECT |
| 1344 | bool |
| 1345 | depends on B44 && SSB_PCIHOST_POSSIBLE |
| 1346 | select SSB_PCIHOST |
| 1347 | default y |
| 1348 | |
| 1349 | # Auto-select SSB PCICORE driver, if possible |
| 1350 | config B44_PCICORE_AUTOSELECT |
| 1351 | bool |
| 1352 | depends on B44 && SSB_DRIVER_PCICORE_POSSIBLE |
| 1353 | select SSB_DRIVER_PCICORE |
| 1354 | default y |
| 1355 | |
| 1356 | config B44_PCI |
| 1357 | bool |
| 1358 | depends on B44_PCI_AUTOSELECT && B44_PCICORE_AUTOSELECT |
| 1359 | default y |
| 1360 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1361 | config FORCEDETH |
Adrian Bunk | 8277008 | 2006-03-08 00:06:30 -0800 | [diff] [blame] | 1362 | tristate "nForce Ethernet support" |
| 1363 | depends on NET_PCI && PCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1364 | help |
| 1365 | If you have a network (Ethernet) controller of this type, say Y and |
| 1366 | read the Ethernet-HOWTO, available from |
| 1367 | <http://www.tldp.org/docs.html#howto>. |
| 1368 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1369 | To compile this driver as a module, choose M here. The module |
| 1370 | will be called forcedeth. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1371 | |
Stephen Hemminger | e27cdba | 2006-07-31 20:37:19 -0700 | [diff] [blame] | 1372 | config FORCEDETH_NAPI |
Randy Dunlap | bf45abe | 2007-10-18 17:16:20 -0700 | [diff] [blame] | 1373 | bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" |
Stephen Hemminger | e27cdba | 2006-07-31 20:37:19 -0700 | [diff] [blame] | 1374 | depends on FORCEDETH && EXPERIMENTAL |
| 1375 | help |
| 1376 | NAPI is a new driver API designed to reduce CPU and interrupt load |
| 1377 | when the driver is receiving lots of packets from the card. It is |
| 1378 | still somewhat experimental and thus not yet enabled by default. |
| 1379 | |
| 1380 | If your estimated Rx load is 10kpps or more, or if the card will be |
| 1381 | deployed on potentially unfriendly networks (e.g. in a firewall), |
| 1382 | then say Y here. |
| 1383 | |
Stephen Hemminger | e27cdba | 2006-07-31 20:37:19 -0700 | [diff] [blame] | 1384 | If in doubt, say N. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1385 | |
| 1386 | config CS89x0 |
| 1387 | tristate "CS89x0 support" |
Deepak Saxena | 9c87896 | 2006-01-14 13:21:18 -0800 | [diff] [blame] | 1388 | depends on NET_PCI && (ISA || MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1389 | ---help--- |
| 1390 | Support for CS89x0 chipset based Ethernet cards. If you have a |
| 1391 | network (Ethernet) card of this type, say Y and read the |
| 1392 | Ethernet-HOWTO, available from |
| 1393 | <http://www.tldp.org/docs.html#howto> as well as |
| 1394 | <file:Documentation/networking/cs89x0.txt>. |
| 1395 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1396 | To compile this driver as a module, choose M here. The module |
| 1397 | will be called cs89x0. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1398 | |
| 1399 | config TC35815 |
| 1400 | tristate "TOSHIBA TC35815 Ethernet support" |
Atsushi Nemoto | eea221c | 2007-03-03 23:54:59 +0900 | [diff] [blame] | 1401 | depends on NET_PCI && PCI && MIPS |
| 1402 | select MII |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1403 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1404 | config EEPRO100 |
| 1405 | tristate "EtherExpressPro/100 support (eepro100, original Becker driver)" |
| 1406 | depends on NET_PCI && PCI |
| 1407 | select MII |
| 1408 | help |
| 1409 | If you have an Intel EtherExpress PRO/100 PCI network (Ethernet) |
| 1410 | card, say Y and read the Ethernet-HOWTO, available from |
| 1411 | <http://www.tldp.org/docs.html#howto>. |
| 1412 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1413 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1414 | will be called eepro100. |
| 1415 | |
| 1416 | |
| 1417 | config E100 |
| 1418 | tristate "Intel(R) PRO/100+ support" |
| 1419 | depends on NET_PCI && PCI |
| 1420 | select MII |
| 1421 | ---help--- |
| 1422 | This driver supports Intel(R) PRO/100 family of adapters. |
| 1423 | To verify that your adapter is supported, find the board ID number |
| 1424 | on the adapter. Look for a label that has a barcode and a number |
| 1425 | in the format 123456-001 (six digits hyphen three digits). |
| 1426 | |
| 1427 | Use the above information and the Adapter & Driver ID Guide at: |
| 1428 | |
| 1429 | <http://support.intel.com/support/network/adapter/pro100/21397.htm> |
| 1430 | |
| 1431 | to identify the adapter. |
| 1432 | |
| 1433 | For the latest Intel PRO/100 network driver for Linux, see: |
| 1434 | |
| 1435 | <http://appsr.intel.com/scripts-df/support_intel.asp> |
| 1436 | |
| 1437 | More specific information on configuring the driver is in |
| 1438 | <file:Documentation/networking/e100.txt>. |
| 1439 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1440 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1441 | will be called e100. |
| 1442 | |
| 1443 | config LNE390 |
| 1444 | tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)" |
| 1445 | depends on NET_PCI && EISA && EXPERIMENTAL |
| 1446 | select CRC32 |
| 1447 | help |
| 1448 | If you have a network (Ethernet) card of this type, say Y and read |
| 1449 | the Ethernet-HOWTO, available from |
| 1450 | <http://www.tldp.org/docs.html#howto>. |
| 1451 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1452 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1453 | will be called lne390. |
| 1454 | |
| 1455 | config FEALNX |
| 1456 | tristate "Myson MTD-8xx PCI Ethernet support" |
| 1457 | depends on NET_PCI && PCI |
| 1458 | select CRC32 |
| 1459 | select MII |
| 1460 | help |
| 1461 | Say Y here to support the Mysom MTD-800 family of PCI-based Ethernet |
| 1462 | cards. Specifications and data at |
| 1463 | <http://www.myson.com.hk/mtd/datasheet/>. |
| 1464 | |
| 1465 | config NATSEMI |
| 1466 | tristate "National Semiconductor DP8381x series PCI Ethernet support" |
| 1467 | depends on NET_PCI && PCI |
| 1468 | select CRC32 |
| 1469 | help |
| 1470 | This driver is for the National Semiconductor DP83810 series, |
| 1471 | which is used in cards from PureData, NetGear, Linksys |
| 1472 | and others, including the 83815 chip. |
| 1473 | More specific information and updates are available from |
| 1474 | <http://www.scyld.com/network/natsemi.html>. |
| 1475 | |
| 1476 | config NE2K_PCI |
| 1477 | tristate "PCI NE2000 and clones support (see help)" |
| 1478 | depends on NET_PCI && PCI |
| 1479 | select CRC32 |
| 1480 | ---help--- |
| 1481 | This driver is for NE2000 compatible PCI cards. It will not work |
| 1482 | with ISA NE2000 cards (they have their own driver, "NE2000/NE1000 |
| 1483 | support" below). If you have a PCI NE2000 network (Ethernet) card, |
| 1484 | say Y and read the Ethernet-HOWTO, available from |
| 1485 | <http://www.tldp.org/docs.html#howto>. |
| 1486 | |
| 1487 | This driver also works for the following NE2000 clone cards: |
| 1488 | RealTek RTL-8029 Winbond 89C940 Compex RL2000 KTI ET32P2 |
| 1489 | NetVin NV5000SC Via 86C926 SureCom NE34 Winbond |
| 1490 | Holtek HT80232 Holtek HT80229 |
| 1491 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1492 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1493 | will be called ne2k-pci. |
| 1494 | |
| 1495 | config NE3210 |
| 1496 | tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)" |
| 1497 | depends on NET_PCI && EISA && EXPERIMENTAL |
| 1498 | select CRC32 |
| 1499 | ---help--- |
| 1500 | If you have a network (Ethernet) card of this type, say Y and read |
| 1501 | the Ethernet-HOWTO, available from |
| 1502 | <http://www.tldp.org/docs.html#howto>. Note that this driver |
| 1503 | will NOT WORK for NE3200 cards as they are completely different. |
| 1504 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1505 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1506 | will be called ne3210. |
| 1507 | |
| 1508 | config ES3210 |
| 1509 | tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)" |
| 1510 | depends on NET_PCI && EISA && EXPERIMENTAL |
| 1511 | select CRC32 |
| 1512 | help |
| 1513 | If you have a network (Ethernet) card of this type, say Y and read |
| 1514 | the Ethernet-HOWTO, available from |
| 1515 | <http://www.tldp.org/docs.html#howto>. |
| 1516 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1517 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1518 | will be called es3210. |
| 1519 | |
| 1520 | config 8139CP |
| 1521 | tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)" |
| 1522 | depends on NET_PCI && PCI && EXPERIMENTAL |
| 1523 | select CRC32 |
| 1524 | select MII |
| 1525 | help |
| 1526 | This is a driver for the Fast Ethernet PCI network cards based on |
| 1527 | the RTL8139C+ chips. If you have one of those, say Y and read |
| 1528 | the Ethernet-HOWTO, available from |
| 1529 | <http://www.tldp.org/docs.html#howto>. |
| 1530 | |
| 1531 | To compile this driver as a module, choose M here: the module |
| 1532 | will be called 8139cp. This is recommended. |
| 1533 | |
| 1534 | config 8139TOO |
Adrian Bunk | f04e3f0 | 2005-05-16 21:13:03 +0200 | [diff] [blame] | 1535 | tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1536 | depends on NET_PCI && PCI |
| 1537 | select CRC32 |
| 1538 | select MII |
| 1539 | ---help--- |
| 1540 | This is a driver for the Fast Ethernet PCI network cards based on |
Adrian Bunk | f04e3f0 | 2005-05-16 21:13:03 +0200 | [diff] [blame] | 1541 | the RTL 8129/8130/8139 chips. If you have one of those, say Y and |
| 1542 | read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1543 | |
| 1544 | To compile this driver as a module, choose M here: the module |
| 1545 | will be called 8139too. This is recommended. |
| 1546 | |
| 1547 | config 8139TOO_PIO |
| 1548 | bool "Use PIO instead of MMIO" |
| 1549 | default y |
| 1550 | depends on 8139TOO |
| 1551 | help |
| 1552 | This instructs the driver to use programmed I/O ports (PIO) instead |
| 1553 | of PCI shared memory (MMIO). This can possibly solve some problems |
| 1554 | in case your mainboard has memory consistency issues. If unsure, |
| 1555 | say N. |
| 1556 | |
| 1557 | config 8139TOO_TUNE_TWISTER |
| 1558 | bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)" |
| 1559 | depends on 8139TOO |
| 1560 | help |
| 1561 | This implements a function which might come in handy in case you |
| 1562 | are using low quality on long cabling. It is required for RealTek |
| 1563 | RTL-8139 revision K boards, and totally unused otherwise. It tries |
| 1564 | to match the transceiver to the cable characteristics. This is |
| 1565 | experimental since hardly documented by the manufacturer. |
| 1566 | If unsure, say Y. |
| 1567 | |
| 1568 | config 8139TOO_8129 |
| 1569 | bool "Support for older RTL-8129/8130 boards" |
| 1570 | depends on 8139TOO |
| 1571 | help |
| 1572 | This enables support for the older and uncommon RTL-8129 and |
| 1573 | RTL-8130 chips, which support MII via an external transceiver, |
| 1574 | instead of an internal one. Disabling this option will save some |
| 1575 | memory by making the code size smaller. If unsure, say Y. |
| 1576 | |
| 1577 | config 8139_OLD_RX_RESET |
| 1578 | bool "Use older RX-reset method" |
| 1579 | depends on 8139TOO |
| 1580 | help |
| 1581 | The 8139too driver was recently updated to contain a more rapid |
| 1582 | reset sequence, in the face of severe receive errors. This "new" |
| 1583 | RX-reset method should be adequate for all boards. But if you |
| 1584 | experience problems, you can enable this option to restore the |
| 1585 | old RX-reset behavior. If unsure, say N. |
| 1586 | |
| 1587 | config SIS900 |
| 1588 | tristate "SiS 900/7016 PCI Fast Ethernet Adapter support" |
| 1589 | depends on NET_PCI && PCI |
| 1590 | select CRC32 |
Adrian Bunk | 6da0f68 | 2005-04-30 13:52:49 +0200 | [diff] [blame] | 1591 | select MII |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1592 | ---help--- |
| 1593 | This is a driver for the Fast Ethernet PCI network cards based on |
| 1594 | the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in |
Adrian Bunk | c3cf560 | 2006-03-04 17:07:57 +0100 | [diff] [blame] | 1595 | SiS 630 and SiS 540 chipsets. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1596 | |
| 1597 | This driver also supports AMD 79C901 HomePNA so that you can use |
| 1598 | your phone line as a network cable. |
| 1599 | |
| 1600 | To compile this driver as a module, choose M here: the module |
| 1601 | will be called sis900. This is recommended. |
| 1602 | |
| 1603 | config EPIC100 |
| 1604 | tristate "SMC EtherPower II" |
| 1605 | depends on NET_PCI && PCI |
| 1606 | select CRC32 |
| 1607 | select MII |
| 1608 | help |
| 1609 | This driver is for the SMC EtherPower II 9432 PCI Ethernet NIC, |
| 1610 | which is based on the SMC83c17x (EPIC/100). |
| 1611 | More specific information and updates are available from |
| 1612 | <http://www.scyld.com/network/epic100.html>. |
| 1613 | |
| 1614 | config SUNDANCE |
| 1615 | tristate "Sundance Alta support" |
| 1616 | depends on NET_PCI && PCI |
| 1617 | select CRC32 |
| 1618 | select MII |
| 1619 | help |
| 1620 | This driver is for the Sundance "Alta" chip. |
| 1621 | More specific information and updates are available from |
| 1622 | <http://www.scyld.com/network/sundance.html>. |
| 1623 | |
| 1624 | config SUNDANCE_MMIO |
| 1625 | bool "Use MMIO instead of PIO" |
| 1626 | depends on SUNDANCE |
| 1627 | help |
| 1628 | Enable memory-mapped I/O for interaction with Sundance NIC registers. |
| 1629 | Do NOT enable this by default, PIO (enabled when MMIO is disabled) |
| 1630 | is known to solve bugs on certain chips. |
| 1631 | |
| 1632 | If unsure, say N. |
| 1633 | |
| 1634 | config TLAN |
| 1635 | tristate "TI ThunderLAN support" |
| 1636 | depends on NET_PCI && (PCI || EISA) && !64BIT |
| 1637 | ---help--- |
| 1638 | If you have a PCI Ethernet network card based on the ThunderLAN chip |
| 1639 | which is supported by this driver, say Y and read the |
| 1640 | Ethernet-HOWTO, available from |
| 1641 | <http://www.tldp.org/docs.html#howto>. |
| 1642 | |
| 1643 | Devices currently supported by this driver are Compaq Netelligent, |
| 1644 | Compaq NetFlex and Olicom cards. Please read the file |
| 1645 | <file:Documentation/networking/tlan.txt> for more details. |
| 1646 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1647 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1648 | will be called tlan. |
| 1649 | |
| 1650 | Please email feedback to <torben.mathiasen@compaq.com>. |
| 1651 | |
| 1652 | config VIA_RHINE |
| 1653 | tristate "VIA Rhine support" |
| 1654 | depends on NET_PCI && PCI |
| 1655 | select CRC32 |
| 1656 | select MII |
| 1657 | help |
| 1658 | If you have a VIA "Rhine" based network card (Rhine-I (VT86C100A), |
| 1659 | Rhine-II (VT6102), or Rhine-III (VT6105)), say Y here. Rhine-type |
| 1660 | Ethernet functions can also be found integrated on South Bridges |
| 1661 | (e.g. VT8235). |
| 1662 | |
| 1663 | To compile this driver as a module, choose M here. The module |
| 1664 | will be called via-rhine. |
| 1665 | |
| 1666 | config VIA_RHINE_MMIO |
| 1667 | bool "Use MMIO instead of PIO" |
| 1668 | depends on VIA_RHINE |
| 1669 | help |
| 1670 | This instructs the driver to use PCI shared memory (MMIO) instead of |
| 1671 | programmed I/O ports (PIO). Enabling this gives an improvement in |
| 1672 | processing time in parts of the driver. |
| 1673 | |
| 1674 | If unsure, say Y. |
| 1675 | |
Roger Luethi | 633949a | 2006-08-14 23:00:17 -0700 | [diff] [blame] | 1676 | config VIA_RHINE_NAPI |
| 1677 | bool "Use Rx Polling (NAPI)" |
| 1678 | depends on VIA_RHINE |
| 1679 | help |
| 1680 | NAPI is a new driver API designed to reduce CPU and interrupt load |
| 1681 | when the driver is receiving lots of packets from the card. |
| 1682 | |
| 1683 | If your estimated Rx load is 10kpps or more, or if the card will be |
| 1684 | deployed on potentially unfriendly networks (e.g. in a firewall), |
| 1685 | then say Y here. |
| 1686 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1687 | config LAN_SAA9730 |
Ralf Baechle | f2b67c7 | 2006-11-29 17:10:38 +0000 | [diff] [blame] | 1688 | bool "Philips SAA9730 Ethernet support" |
| 1689 | depends on NET_PCI && PCI && MIPS_ATLAS |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1690 | help |
| 1691 | The SAA9730 is a combined multimedia and peripheral controller used |
| 1692 | in thin clients, Internet access terminals, and diskless |
| 1693 | workstations. |
| 1694 | See <http://www.semiconductors.philips.com/pip/SAA9730_flyer_1>. |
| 1695 | |
Cesar Eduardo Barros | bf34570 | 2006-12-19 13:08:47 -0800 | [diff] [blame] | 1696 | config SC92031 |
| 1697 | tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)" |
| 1698 | depends on NET_PCI && PCI && EXPERIMENTAL |
| 1699 | select CRC32 |
| 1700 | ---help--- |
| 1701 | This is a driver for the Fast Ethernet PCI network cards based on |
| 1702 | the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you |
| 1703 | have one of these, say Y here. |
| 1704 | |
| 1705 | To compile this driver as a module, choose M here: the module |
| 1706 | will be called sc92031. This is recommended. |
| 1707 | |
Matteo Croce | d95b39c | 2007-10-14 18:10:13 +0200 | [diff] [blame] | 1708 | config CPMAC |
| 1709 | tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)" |
| 1710 | depends on NET_ETHERNET && EXPERIMENTAL && AR7 |
| 1711 | select PHYLIB |
| 1712 | select FIXED_PHY |
| 1713 | select FIXED_MII_100_FDX |
| 1714 | help |
| 1715 | TI AR7 CPMAC Ethernet support |
| 1716 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1717 | config NET_POCKET |
| 1718 | bool "Pocket and portable adapters" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 1719 | depends on PARPORT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1720 | ---help--- |
| 1721 | Cute little network (Ethernet) devices which attach to the parallel |
| 1722 | port ("pocket adapters"), commonly used with laptops. If you have |
| 1723 | one of those, say Y and read the Ethernet-HOWTO, available from |
| 1724 | <http://www.tldp.org/docs.html#howto>. |
| 1725 | |
| 1726 | If you want to plug a network (or some other) card into the PCMCIA |
| 1727 | (or PC-card) slot of your laptop instead (PCMCIA is the standard for |
| 1728 | credit card size extension cards used by all modern laptops), you |
| 1729 | need the pcmcia-cs package (location contained in the file |
| 1730 | <file:Documentation/Changes>) and you can say N here. |
| 1731 | |
| 1732 | Laptop users should read the Linux Laptop home page at |
| 1733 | <http://www.linux-on-laptops.com/> or |
| 1734 | Tuxmobil - Linux on Mobile Computers at <http://www.tuxmobil.org/>. |
| 1735 | |
| 1736 | Note that the answer to this question doesn't directly affect the |
| 1737 | kernel: saying N will just cause the configurator to skip all |
| 1738 | the questions about this class of network devices. If you say Y, you |
| 1739 | will be asked for your specific device in the following questions. |
| 1740 | |
| 1741 | config ATP |
| 1742 | tristate "AT-LAN-TEC/RealTek pocket adapter support" |
Grant Coady | 32fa2bf | 2005-09-10 00:14:05 +1000 | [diff] [blame] | 1743 | depends on NET_POCKET && PARPORT && X86 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1744 | select CRC32 |
| 1745 | ---help--- |
| 1746 | This is a network (Ethernet) device which attaches to your parallel |
| 1747 | port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO, |
| 1748 | available from <http://www.tldp.org/docs.html#howto>, if you |
| 1749 | want to use this. If you intend to use this driver, you should have |
| 1750 | said N to the "Parallel printer support", because the two drivers |
| 1751 | don't like each other. |
| 1752 | |
| 1753 | To compile this driver as a module, choose M here: the module |
| 1754 | will be called atp. |
| 1755 | |
| 1756 | config DE600 |
| 1757 | tristate "D-Link DE600 pocket adapter support" |
Grant Coady | 32fa2bf | 2005-09-10 00:14:05 +1000 | [diff] [blame] | 1758 | depends on NET_POCKET && PARPORT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1759 | ---help--- |
| 1760 | This is a network (Ethernet) device which attaches to your parallel |
| 1761 | port. Read <file:Documentation/networking/DLINK.txt> as well as the |
| 1762 | Ethernet-HOWTO, available from |
| 1763 | <http://www.tldp.org/docs.html#howto>, if you want to use |
| 1764 | this. It is possible to have several devices share a single parallel |
| 1765 | port and it is safe to compile the corresponding drivers into the |
| 1766 | kernel. |
| 1767 | |
| 1768 | To compile this driver as a module, choose M here: the module |
| 1769 | will be called de600. |
| 1770 | |
| 1771 | config DE620 |
| 1772 | tristate "D-Link DE620 pocket adapter support" |
Grant Coady | 32fa2bf | 2005-09-10 00:14:05 +1000 | [diff] [blame] | 1773 | depends on NET_POCKET && PARPORT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1774 | ---help--- |
| 1775 | This is a network (Ethernet) device which attaches to your parallel |
| 1776 | port. Read <file:Documentation/networking/DLINK.txt> as well as the |
| 1777 | Ethernet-HOWTO, available from |
| 1778 | <http://www.tldp.org/docs.html#howto>, if you want to use |
| 1779 | this. It is possible to have several devices share a single parallel |
| 1780 | port and it is safe to compile the corresponding drivers into the |
| 1781 | kernel. |
| 1782 | |
| 1783 | To compile this driver as a module, choose M here: the module |
| 1784 | will be called de620. |
| 1785 | |
| 1786 | config SGISEEQ |
| 1787 | tristate "SGI Seeq ethernet controller support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 1788 | depends on SGI_IP22 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1789 | help |
| 1790 | Say Y here if you have an Seeq based Ethernet network card. This is |
| 1791 | used in many Silicon Graphics machines. |
| 1792 | |
| 1793 | config DECLANCE |
| 1794 | tristate "DEC LANCE ethernet controller support" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 1795 | depends on MACH_DECSTATION |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1796 | select CRC32 |
| 1797 | help |
| 1798 | This driver is for the series of Ethernet controllers produced by |
| 1799 | DEC (now Compaq) based on the AMD Lance chipset, including the |
| 1800 | DEPCA series. (This chipset is better known via the NE2100 cards.) |
| 1801 | |
| 1802 | config 68360_ENET |
| 1803 | bool "Motorola 68360 ethernet controller" |
| 1804 | depends on M68360 |
| 1805 | help |
| 1806 | Say Y here if you want to use the built-in ethernet controller of |
| 1807 | the Motorola 68360 processor. |
| 1808 | |
| 1809 | config FEC |
Greg Ungerer | 2af6921 | 2005-09-12 11:18:10 +1000 | [diff] [blame] | 1810 | bool "FEC ethernet controller (of ColdFire CPUs)" |
Greg Ungerer | 892b625 | 2006-01-10 16:58:16 +1000 | [diff] [blame] | 1811 | depends on M523x || M527x || M5272 || M528x || M520x |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1812 | help |
| 1813 | Say Y here if you want to use the built-in 10/100 Fast ethernet |
Greg Ungerer | 2af6921 | 2005-09-12 11:18:10 +1000 | [diff] [blame] | 1814 | controller on some Motorola ColdFire processors. |
| 1815 | |
| 1816 | config FEC2 |
| 1817 | bool "Second FEC ethernet controller (on some ColdFire CPUs)" |
| 1818 | depends on FEC |
| 1819 | help |
| 1820 | Say Y here if you want to use the second built-in 10/100 Fast |
| 1821 | ethernet controller on some Motorola ColdFire processors. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1822 | |
Domen Puncer | 5d031e9 | 2007-10-26 18:07:49 +0200 | [diff] [blame] | 1823 | config FEC_MPC52xx |
| 1824 | tristate "MPC52xx FEC driver" |
Grant Likely | 644fdf9 | 2007-11-01 08:22:30 -0600 | [diff] [blame] | 1825 | depends on PPC_MERGE && PPC_MPC52xx && PPC_BESTCOMM_FEC |
Domen Puncer | 5d031e9 | 2007-10-26 18:07:49 +0200 | [diff] [blame] | 1826 | select CRC32 |
| 1827 | select PHYLIB |
| 1828 | ---help--- |
| 1829 | This option enables support for the MPC5200's on-chip |
| 1830 | Fast Ethernet Controller |
| 1831 | If compiled as module, it will be called 'fec_mpc52xx.ko'. |
| 1832 | |
| 1833 | config FEC_MPC52xx_MDIO |
| 1834 | bool "MPC52xx FEC MDIO bus driver" |
| 1835 | depends on FEC_MPC52xx |
| 1836 | default y |
| 1837 | ---help--- |
| 1838 | The MPC5200's FEC can connect to the Ethernet either with |
| 1839 | an external MII PHY chip or 10 Mbps 7-wire interface |
| 1840 | (Motorola? industry standard). |
| 1841 | If your board uses an external PHY connected to FEC, enable this. |
| 1842 | If not sure, enable. |
| 1843 | If compiled as module, it will be called 'fec_mpc52xx_phy.ko'. |
| 1844 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1845 | config NE_H8300 |
| 1846 | tristate "NE2000 compatible support for H8/300" |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 1847 | depends on H8300 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1848 | help |
| 1849 | Say Y here if you want to use the NE2000 compatible |
| 1850 | controller on the Renesas H8/300 processor. |
| 1851 | |
| 1852 | source "drivers/net/fec_8xx/Kconfig" |
Pantelis Antoniou | 48257c4 | 2005-10-28 16:25:58 -0400 | [diff] [blame] | 1853 | source "drivers/net/fs_enet/Kconfig" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1854 | |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 1855 | endif # NET_ETHERNET |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1856 | |
| 1857 | # |
| 1858 | # Gigabit Ethernet |
| 1859 | # |
| 1860 | |
Jan Engelhardt | f30486d | 2007-05-10 22:52:56 -0700 | [diff] [blame] | 1861 | menuconfig NETDEV_1000 |
| 1862 | bool "Ethernet (1000 Mbit)" |
Randy Dunlap | cbcd2a4 | 2005-07-27 13:04:35 -0700 | [diff] [blame] | 1863 | depends on !UML |
Jan Engelhardt | f30486d | 2007-05-10 22:52:56 -0700 | [diff] [blame] | 1864 | default y |
Jan Engelhardt | 06bfb7e | 2007-08-18 12:56:21 +0200 | [diff] [blame] | 1865 | ---help--- |
| 1866 | Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common |
| 1867 | type of Local Area Network (LAN) in universities and companies. |
| 1868 | |
| 1869 | Say Y here to get to see options for Gigabit Ethernet drivers. |
| 1870 | This option alone does not add any kernel code. |
| 1871 | Note that drivers supporting both 100 and 1000 MBit may be listed |
| 1872 | under "Ethernet (10 or 100MBit)" instead. |
| 1873 | |
| 1874 | If you say N, all options in this submenu will be skipped and disabled. |
Jan Engelhardt | f30486d | 2007-05-10 22:52:56 -0700 | [diff] [blame] | 1875 | |
| 1876 | if NETDEV_1000 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1877 | |
| 1878 | config ACENIC |
| 1879 | tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support" |
| 1880 | depends on PCI |
| 1881 | ---help--- |
| 1882 | Say Y here if you have an Alteon AceNIC, 3Com 3C985(B), NetGear |
| 1883 | GA620, SGI Gigabit or Farallon PN9000-SX PCI Gigabit Ethernet |
| 1884 | adapter. The driver allows for using the Jumbo Frame option (9000 |
| 1885 | bytes/frame) however it requires that your switches can handle this |
| 1886 | as well. To enable Jumbo Frames, add `mtu 9000' to your ifconfig |
| 1887 | line. |
| 1888 | |
| 1889 | To compile this driver as a module, choose M here: the |
| 1890 | module will be called acenic. |
| 1891 | |
| 1892 | config ACENIC_OMIT_TIGON_I |
| 1893 | bool "Omit support for old Tigon I based AceNICs" |
| 1894 | depends on ACENIC |
| 1895 | help |
| 1896 | Say Y here if you only have Tigon II based AceNICs and want to leave |
| 1897 | out support for the older Tigon I based cards which are no longer |
| 1898 | being sold (ie. the original Alteon AceNIC and 3Com 3C985 (non B |
| 1899 | version)). This will reduce the size of the driver object by |
| 1900 | app. 100KB. If you are not sure whether your card is a Tigon I or a |
| 1901 | Tigon II, say N here. |
| 1902 | |
| 1903 | The safe and default value for this is N. |
| 1904 | |
| 1905 | config DL2K |
Komuro | df95082 | 2007-08-13 09:45:41 +0900 | [diff] [blame] | 1906 | tristate "DL2000/TC902x-based Gigabit Ethernet support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1907 | depends on PCI |
| 1908 | select CRC32 |
| 1909 | help |
Komuro | df95082 | 2007-08-13 09:45:41 +0900 | [diff] [blame] | 1910 | This driver supports DL2000/TC902x-based Gigabit ethernet cards, |
| 1911 | which includes |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1912 | D-Link DGE-550T Gigabit Ethernet Adapter. |
| 1913 | D-Link DL2000-based Gigabit Ethernet Adapter. |
Komuro | df95082 | 2007-08-13 09:45:41 +0900 | [diff] [blame] | 1914 | Sundance/Tamarack TC902x Gigabit Ethernet Adapter. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1915 | |
| 1916 | To compile this driver as a module, choose M here: the |
| 1917 | module will be called dl2k. |
| 1918 | |
| 1919 | config E1000 |
| 1920 | tristate "Intel(R) PRO/1000 Gigabit Ethernet support" |
| 1921 | depends on PCI |
| 1922 | ---help--- |
| 1923 | This driver supports Intel(R) PRO/1000 gigabit ethernet family of |
| 1924 | adapters. For more information on how to identify your adapter, go |
| 1925 | to the Adapter & Driver ID Guide at: |
| 1926 | |
| 1927 | <http://support.intel.com/support/network/adapter/pro100/21397.htm> |
| 1928 | |
| 1929 | For general information and support, go to the Intel support |
| 1930 | website at: |
| 1931 | |
| 1932 | <http://support.intel.com> |
| 1933 | |
| 1934 | More specific information on configuring the driver is in |
| 1935 | <file:Documentation/networking/e1000.txt>. |
| 1936 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1937 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1938 | will be called e1000. |
| 1939 | |
| 1940 | config E1000_NAPI |
| 1941 | bool "Use Rx Polling (NAPI)" |
| 1942 | depends on E1000 |
| 1943 | help |
| 1944 | NAPI is a new driver API designed to reduce CPU and interrupt load |
| 1945 | when the driver is receiving lots of packets from the card. It is |
| 1946 | still somewhat experimental and thus not yet enabled by default. |
| 1947 | |
| 1948 | If your estimated Rx load is 10kpps or more, or if the card will be |
| 1949 | deployed on potentially unfriendly networks (e.g. in a firewall), |
| 1950 | then say Y here. |
| 1951 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1952 | If in doubt, say N. |
| 1953 | |
Jesse Brandeburg | 35ec56b | 2006-01-18 13:01:30 -0800 | [diff] [blame] | 1954 | config E1000_DISABLE_PACKET_SPLIT |
| 1955 | bool "Disable Packet Split for PCI express adapters" |
| 1956 | depends on E1000 |
| 1957 | help |
| 1958 | Say Y here if you want to use the legacy receive path for PCI express |
James Ring | 9e6b487 | 2006-03-22 00:51:11 +0100 | [diff] [blame] | 1959 | hardware. |
Jesse Brandeburg | 35ec56b | 2006-01-18 13:01:30 -0800 | [diff] [blame] | 1960 | |
| 1961 | If in doubt, say N. |
| 1962 | |
Auke Kok | bc7f75f | 2007-09-17 12:30:59 -0700 | [diff] [blame] | 1963 | config E1000E |
| 1964 | tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support" |
| 1965 | depends on PCI |
| 1966 | ---help--- |
| 1967 | This driver supports the PCI-Express Intel(R) PRO/1000 gigabit |
| 1968 | ethernet family of adapters. For PCI or PCI-X e1000 adapters, |
| 1969 | use the regular e1000 driver For more information on how to |
| 1970 | identify your adapter, go to the Adapter & Driver ID Guide at: |
| 1971 | |
| 1972 | <http://support.intel.com/support/network/adapter/pro100/21397.htm> |
| 1973 | |
| 1974 | For general information and support, go to the Intel support |
| 1975 | website at: |
| 1976 | |
| 1977 | <http://support.intel.com> |
| 1978 | |
| 1979 | More specific information on configuring the driver is in |
| 1980 | <file:Documentation/networking/e1000e.txt>. |
| 1981 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 1982 | To compile this driver as a module, choose M here. The module |
Auke Kok | bc7f75f | 2007-09-17 12:30:59 -0700 | [diff] [blame] | 1983 | will be called e1000e. |
| 1984 | |
Stephen Hemminger | ab7a983 | 2008-01-01 09:27:58 -0800 | [diff] [blame^] | 1985 | config IP1000 |
| 1986 | tristate "IP1000 Gigabit Ethernet support" |
| 1987 | depends on PCI && EXPERIMENTAL |
| 1988 | select MII |
| 1989 | ---help--- |
| 1990 | This driver supports IP1000 gigabit Ethernet cards. |
| 1991 | |
| 1992 | To compile this driver as a module, choose M here: the module |
| 1993 | will be called ipg. This is recommended. |
| 1994 | |
Lennert Buytenhek | 15d014d | 2005-11-11 18:23:13 +0100 | [diff] [blame] | 1995 | source "drivers/net/ixp2000/Kconfig" |
| 1996 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1997 | config MYRI_SBUS |
| 1998 | tristate "MyriCOM Gigabit Ethernet support" |
| 1999 | depends on SBUS |
| 2000 | help |
| 2001 | This driver supports MyriCOM Sbus gigabit Ethernet cards. |
| 2002 | |
| 2003 | To compile this driver as a module, choose M here: the module |
| 2004 | will be called myri_sbus. This is recommended. |
| 2005 | |
| 2006 | config NS83820 |
Jon Mason | 47c5143 | 2006-02-12 11:53:04 -0600 | [diff] [blame] | 2007 | tristate "National Semiconductor DP83820 support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2008 | depends on PCI |
| 2009 | help |
| 2010 | This is a driver for the National Semiconductor DP83820 series |
| 2011 | of gigabit ethernet MACs. Cards using this chipset include |
| 2012 | the D-Link DGE-500T, PureData's PDP8023Z-TG, SMC's SMC9462TX, |
| 2013 | SOHO-GA2000T, SOHO-GA2500T. The driver supports the use of |
| 2014 | zero copy. |
| 2015 | |
| 2016 | config HAMACHI |
| 2017 | tristate "Packet Engines Hamachi GNIC-II support" |
| 2018 | depends on PCI |
| 2019 | select MII |
| 2020 | help |
| 2021 | If you have a Gigabit Ethernet card of this type, say Y and read |
| 2022 | the Ethernet-HOWTO, available from |
| 2023 | <http://www.tldp.org/docs.html#howto>. |
| 2024 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 2025 | To compile this driver as a module, choose M here. The module will be |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2026 | called hamachi. |
| 2027 | |
| 2028 | config YELLOWFIN |
| 2029 | tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)" |
| 2030 | depends on PCI && EXPERIMENTAL |
| 2031 | select CRC32 |
| 2032 | ---help--- |
| 2033 | Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet |
| 2034 | adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is |
| 2035 | used by the Beowulf Linux cluster project. See |
| 2036 | <http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more |
| 2037 | information about this driver in particular and Beowulf in general. |
| 2038 | |
| 2039 | To compile this driver as a module, choose M here: the module |
| 2040 | will be called yellowfin. This is recommended. |
| 2041 | |
| 2042 | config R8169 |
| 2043 | tristate "Realtek 8169 gigabit ethernet support" |
| 2044 | depends on PCI |
| 2045 | select CRC32 |
| 2046 | ---help--- |
| 2047 | Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter. |
| 2048 | |
| 2049 | To compile this driver as a module, choose M here: the module |
| 2050 | will be called r8169. This is recommended. |
| 2051 | |
| 2052 | config R8169_NAPI |
Randy Dunlap | bf45abe | 2007-10-18 17:16:20 -0700 | [diff] [blame] | 2053 | bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2054 | depends on R8169 && EXPERIMENTAL |
| 2055 | help |
| 2056 | NAPI is a new driver API designed to reduce CPU and interrupt load |
| 2057 | when the driver is receiving lots of packets from the card. It is |
| 2058 | still somewhat experimental and thus not yet enabled by default. |
| 2059 | |
| 2060 | If your estimated Rx load is 10kpps or more, or if the card will be |
| 2061 | deployed on potentially unfriendly networks (e.g. in a firewall), |
| 2062 | then say Y here. |
| 2063 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2064 | If in doubt, say N. |
| 2065 | |
| 2066 | config R8169_VLAN |
| 2067 | bool "VLAN support" |
| 2068 | depends on R8169 && VLAN_8021Q |
| 2069 | ---help--- |
| 2070 | Say Y here for the r8169 driver to support the functions required |
| 2071 | by the kernel 802.1Q code. |
| 2072 | |
| 2073 | If in doubt, say Y. |
| 2074 | |
Maciej W. Rozycki | 1a9e854 | 2007-09-14 12:05:00 +0100 | [diff] [blame] | 2075 | config SB1250_MAC |
Maciej W. Rozycki | 25a72df | 2007-09-14 11:57:33 +0100 | [diff] [blame] | 2076 | tristate "SB1250 Gigabit Ethernet support" |
| 2077 | depends on SIBYTE_SB1xxx_SOC |
Maciej W. Rozycki | f5279ff | 2007-09-21 12:52:10 +0100 | [diff] [blame] | 2078 | select PHYLIB |
Maciej W. Rozycki | 25a72df | 2007-09-14 11:57:33 +0100 | [diff] [blame] | 2079 | ---help--- |
| 2080 | This driver supports Gigabit Ethernet interfaces based on the |
| 2081 | Broadcom SiByte family of System-On-a-Chip parts. They include |
| 2082 | the BCM1120, BCM1125, BCM1125H, BCM1250, BCM1255, BCM1280, BCM1455 |
| 2083 | and BCM1480 chips. |
| 2084 | |
| 2085 | To compile this driver as a module, choose M here: the module |
| 2086 | will be called sb1250-mac. |
| 2087 | |
Francois Romieu | 890e8d0 | 2005-07-30 13:08:43 +0200 | [diff] [blame] | 2088 | config SIS190 |
Francois Romieu | e797637 | 2005-09-03 00:57:51 +0200 | [diff] [blame] | 2089 | tristate "SiS190/SiS191 gigabit ethernet support" |
Adrian Bunk | e9985d5 | 2005-08-09 02:41:00 +0200 | [diff] [blame] | 2090 | depends on PCI |
| 2091 | select CRC32 |
| 2092 | select MII |
| 2093 | ---help--- |
Francois Romieu | e797637 | 2005-09-03 00:57:51 +0200 | [diff] [blame] | 2094 | Say Y here if you have a SiS 190 PCI Fast Ethernet adapter or |
| 2095 | a SiS 191 PCI Gigabit Ethernet adapter. Both are expected to |
| 2096 | appear in lan on motherboard designs which are based on SiS 965 |
| 2097 | and SiS 966 south bridge. |
Francois Romieu | 890e8d0 | 2005-07-30 13:08:43 +0200 | [diff] [blame] | 2098 | |
Adrian Bunk | e9985d5 | 2005-08-09 02:41:00 +0200 | [diff] [blame] | 2099 | To compile this driver as a module, choose M here: the module |
| 2100 | will be called sis190. This is recommended. |
Francois Romieu | 890e8d0 | 2005-07-30 13:08:43 +0200 | [diff] [blame] | 2101 | |
Stephen Hemminger | baef58b | 2005-05-12 20:14:36 -0400 | [diff] [blame] | 2102 | config SKGE |
Stephen Hemminger | 7a160c7 | 2006-02-13 15:48:08 -0800 | [diff] [blame] | 2103 | tristate "New SysKonnect GigaEthernet support" |
| 2104 | depends on PCI |
Stephen Hemminger | baef58b | 2005-05-12 20:14:36 -0400 | [diff] [blame] | 2105 | select CRC32 |
| 2106 | ---help--- |
| 2107 | This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx |
| 2108 | and related Gigabit Ethernet adapters. It is a new smaller driver |
Stephen Hemminger | 46a60f2 | 2005-09-09 12:54:56 -0700 | [diff] [blame] | 2109 | with better performance and more complete ethtool support. |
Stephen Hemminger | baef58b | 2005-05-12 20:14:36 -0400 | [diff] [blame] | 2110 | |
| 2111 | It does not support the link failover and network management |
Stephen Hemminger | 5ad887f | 2007-09-15 19:35:14 -0400 | [diff] [blame] | 2112 | features that "portable" vendor supplied sk98lin driver does. |
Stephen Hemminger | cd28ab6 | 2005-08-16 16:36:49 -0700 | [diff] [blame] | 2113 | |
Daniel Drake | c6f0d75 | 2006-01-21 19:35:34 +0000 | [diff] [blame] | 2114 | This driver supports adapters based on the original Yukon chipset: |
| 2115 | Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T, |
| 2116 | Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872. |
| 2117 | |
| 2118 | It does not support the newer Yukon2 chipset: a separate driver, |
| 2119 | sky2, is provided for Yukon2-based adapters. |
| 2120 | |
| 2121 | To compile this driver as a module, choose M here: the module |
| 2122 | will be called skge. This is recommended. |
Stephen Hemminger | cd28ab6 | 2005-08-16 16:36:49 -0700 | [diff] [blame] | 2123 | |
Stephen Hemminger | 678aa1f | 2007-10-16 12:15:54 -0700 | [diff] [blame] | 2124 | config SKGE_DEBUG |
| 2125 | bool "Debugging interface" |
| 2126 | depends on SKGE && DEBUG_FS |
| 2127 | help |
| 2128 | This option adds the ability to dump driver state for debugging. |
| 2129 | The file debugfs/skge/ethX displays the state of the internal |
| 2130 | transmit and receive rings. |
| 2131 | |
| 2132 | If unsure, say N. |
| 2133 | |
Stephen Hemminger | cd28ab6 | 2005-08-16 16:36:49 -0700 | [diff] [blame] | 2134 | config SKY2 |
Stephen Hemminger | 8a3e3bf | 2007-07-09 15:33:38 -0700 | [diff] [blame] | 2135 | tristate "SysKonnect Yukon2 support" |
Stephen Hemminger | f479b32 | 2006-10-27 10:22:10 -0700 | [diff] [blame] | 2136 | depends on PCI |
Stephen Hemminger | cd28ab6 | 2005-08-16 16:36:49 -0700 | [diff] [blame] | 2137 | select CRC32 |
| 2138 | ---help--- |
Matt LaPlante | cab0089 | 2006-10-03 22:36:44 +0200 | [diff] [blame] | 2139 | This driver supports Gigabit Ethernet adapters based on the |
Daniel Drake | c6f0d75 | 2006-01-21 19:35:34 +0000 | [diff] [blame] | 2140 | Marvell Yukon 2 chipset: |
| 2141 | Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/ |
| 2142 | 88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21 |
| 2143 | |
Stephen Hemminger | f479b32 | 2006-10-27 10:22:10 -0700 | [diff] [blame] | 2144 | There is companion driver for the older Marvell Yukon and |
| 2145 | Genesis based adapters: skge. |
Stephen Hemminger | cd28ab6 | 2005-08-16 16:36:49 -0700 | [diff] [blame] | 2146 | |
| 2147 | To compile this driver as a module, choose M here: the module |
| 2148 | will be called sky2. This is recommended. |
| 2149 | |
Stephen Hemminger | 3cf2675 | 2007-07-09 15:33:35 -0700 | [diff] [blame] | 2150 | config SKY2_DEBUG |
| 2151 | bool "Debugging interface" |
| 2152 | depends on SKY2 && DEBUG_FS |
| 2153 | help |
| 2154 | This option adds the ability to dump driver state for debugging. |
| 2155 | The file debugfs/sky2/ethX displays the state of the internal |
| 2156 | transmit and receive rings. |
Daniel Drake | c6f0d75 | 2006-01-21 19:35:34 +0000 | [diff] [blame] | 2157 | |
Stephen Hemminger | 3cf2675 | 2007-07-09 15:33:35 -0700 | [diff] [blame] | 2158 | If unsure, say N. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2159 | |
Stephen Hemminger | 5ad887f | 2007-09-15 19:35:14 -0400 | [diff] [blame] | 2160 | config SK98LIN |
| 2161 | tristate "Marvell Yukon Chipset / SysKonnect SK-98xx Support (DEPRECATED)" |
| 2162 | depends on PCI |
| 2163 | ---help--- |
| 2164 | Say Y here if you have a Marvell Yukon or SysKonnect SK-98xx/SK-95xx |
| 2165 | compliant Gigabit Ethernet Adapter. |
| 2166 | |
| 2167 | This driver supports the original Yukon chipset. This driver is |
| 2168 | deprecated and will be removed from the kernel in the near future, |
| 2169 | it has been replaced by the skge driver. skge is cleaner and |
| 2170 | seems to work better. |
| 2171 | |
| 2172 | This driver does not support the newer Yukon2 chipset. A separate |
| 2173 | driver, sky2, is provided to support Yukon2-based adapters. |
| 2174 | |
| 2175 | The following adapters are supported by this driver: |
| 2176 | - 3Com 3C940 Gigabit LOM Ethernet Adapter |
| 2177 | - 3Com 3C941 Gigabit LOM Ethernet Adapter |
| 2178 | - Allied Telesyn AT-2970LX Gigabit Ethernet Adapter |
| 2179 | - Allied Telesyn AT-2970LX/2SC Gigabit Ethernet Adapter |
| 2180 | - Allied Telesyn AT-2970SX Gigabit Ethernet Adapter |
| 2181 | - Allied Telesyn AT-2970SX/2SC Gigabit Ethernet Adapter |
| 2182 | - Allied Telesyn AT-2970TX Gigabit Ethernet Adapter |
| 2183 | - Allied Telesyn AT-2970TX/2TX Gigabit Ethernet Adapter |
| 2184 | - Allied Telesyn AT-2971SX Gigabit Ethernet Adapter |
| 2185 | - Allied Telesyn AT-2971T Gigabit Ethernet Adapter |
| 2186 | - Belkin Gigabit Desktop Card 10/100/1000Base-T Adapter, Copper RJ-45 |
| 2187 | - EG1032 v2 Instant Gigabit Network Adapter |
| 2188 | - EG1064 v2 Instant Gigabit Network Adapter |
| 2189 | - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Abit) |
| 2190 | - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Albatron) |
| 2191 | - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Asus) |
| 2192 | - Marvell 88E8001 Gigabit LOM Ethernet Adapter (ECS) |
| 2193 | - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Epox) |
| 2194 | - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Foxconn) |
| 2195 | - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Gigabyte) |
| 2196 | - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Iwill) |
| 2197 | - Marvell 88E8050 Gigabit LOM Ethernet Adapter (Intel) |
| 2198 | - Marvell RDK-8001 Adapter |
| 2199 | - Marvell RDK-8002 Adapter |
| 2200 | - Marvell RDK-8003 Adapter |
| 2201 | - Marvell RDK-8004 Adapter |
| 2202 | - Marvell RDK-8006 Adapter |
| 2203 | - Marvell RDK-8007 Adapter |
| 2204 | - Marvell RDK-8008 Adapter |
| 2205 | - Marvell RDK-8009 Adapter |
| 2206 | - Marvell RDK-8010 Adapter |
| 2207 | - Marvell RDK-8011 Adapter |
| 2208 | - Marvell RDK-8012 Adapter |
| 2209 | - Marvell RDK-8052 Adapter |
| 2210 | - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (32 bit) |
| 2211 | - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (64 bit) |
| 2212 | - N-Way PCI-Bus Giga-Card 1000/100/10Mbps(L) |
| 2213 | - SK-9521 10/100/1000Base-T Adapter |
| 2214 | - SK-9521 V2.0 10/100/1000Base-T Adapter |
| 2215 | - SK-9821 Gigabit Ethernet Server Adapter (SK-NET GE-T) |
| 2216 | - SK-9821 V2.0 Gigabit Ethernet 10/100/1000Base-T Adapter |
| 2217 | - SK-9822 Gigabit Ethernet Server Adapter (SK-NET GE-T dual link) |
| 2218 | - SK-9841 Gigabit Ethernet Server Adapter (SK-NET GE-LX) |
| 2219 | - SK-9841 V2.0 Gigabit Ethernet 1000Base-LX Adapter |
| 2220 | - SK-9842 Gigabit Ethernet Server Adapter (SK-NET GE-LX dual link) |
| 2221 | - SK-9843 Gigabit Ethernet Server Adapter (SK-NET GE-SX) |
| 2222 | - SK-9843 V2.0 Gigabit Ethernet 1000Base-SX Adapter |
| 2223 | - SK-9844 Gigabit Ethernet Server Adapter (SK-NET GE-SX dual link) |
| 2224 | - SK-9851 V2.0 Gigabit Ethernet 1000Base-SX Adapter |
| 2225 | - SK-9861 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition) |
| 2226 | - SK-9861 V2.0 Gigabit Ethernet 1000Base-SX Adapter |
| 2227 | - SK-9862 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition dual link) |
| 2228 | - SK-9871 Gigabit Ethernet Server Adapter (SK-NET GE-ZX) |
| 2229 | - SK-9871 V2.0 Gigabit Ethernet 1000Base-ZX Adapter |
| 2230 | - SK-9872 Gigabit Ethernet Server Adapter (SK-NET GE-ZX dual link) |
| 2231 | - SMC EZ Card 1000 (SMC9452TXV.2) |
| 2232 | |
| 2233 | The adapters support Jumbo Frames. |
| 2234 | The dual link adapters support link-failover and dual port features. |
| 2235 | Both Marvell Yukon and SysKonnect SK-98xx/SK-95xx adapters support |
| 2236 | the scatter-gather functionality with sendfile(). Please refer to |
| 2237 | <file:Documentation/networking/sk98lin.txt> for more information about |
| 2238 | optional driver parameters. |
| 2239 | Questions concerning this driver may be addressed to: |
| 2240 | <linux@syskonnect.de> |
| 2241 | |
| 2242 | If you want to compile this driver as a module ( = code which can be |
| 2243 | inserted in and removed from the running kernel whenever you want), |
| 2244 | say M here and read <file:Documentation/kbuild/modules.txt>. The module will |
| 2245 | be called sk98lin. This is recommended. |
| 2246 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2247 | config VIA_VELOCITY |
| 2248 | tristate "VIA Velocity support" |
Yoichi Yuasa | 7381553 | 2007-05-24 16:12:27 +0900 | [diff] [blame] | 2249 | depends on PCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2250 | select CRC32 |
| 2251 | select CRC_CCITT |
| 2252 | select MII |
| 2253 | help |
| 2254 | If you have a VIA "Velocity" based network card say Y here. |
| 2255 | |
| 2256 | To compile this driver as a module, choose M here. The module |
| 2257 | will be called via-velocity. |
| 2258 | |
| 2259 | config TIGON3 |
| 2260 | tristate "Broadcom Tigon3 support" |
| 2261 | depends on PCI |
| 2262 | help |
| 2263 | This driver supports Broadcom Tigon3 based gigabit Ethernet cards. |
| 2264 | |
| 2265 | To compile this driver as a module, choose M here: the module |
| 2266 | will be called tg3. This is recommended. |
| 2267 | |
Michael Chan | b6016b7 | 2005-05-26 13:03:09 -0700 | [diff] [blame] | 2268 | config BNX2 |
| 2269 | tristate "Broadcom NetXtremeII support" |
| 2270 | depends on PCI |
Michael Chan | fba9fe9 | 2006-06-12 22:21:25 -0700 | [diff] [blame] | 2271 | select CRC32 |
| 2272 | select ZLIB_INFLATE |
Michael Chan | b6016b7 | 2005-05-26 13:03:09 -0700 | [diff] [blame] | 2273 | help |
| 2274 | This driver supports Broadcom NetXtremeII gigabit Ethernet cards. |
| 2275 | |
| 2276 | To compile this driver as a module, choose M here: the module |
| 2277 | will be called bnx2. This is recommended. |
| 2278 | |
Jens Osterkamp | aaec0fa | 2005-09-05 15:19:29 -0700 | [diff] [blame] | 2279 | config SPIDER_NET |
| 2280 | tristate "Spider Gigabit Ethernet driver" |
Kou Ishizaki | 3342cf0 | 2007-02-20 16:36:14 -0600 | [diff] [blame] | 2281 | depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB) |
Christoph Hellwig | 9b15879 | 2006-03-15 11:30:44 +0100 | [diff] [blame] | 2282 | select FW_LOADER |
Jens Osterkamp | aaec0fa | 2005-09-05 15:19:29 -0700 | [diff] [blame] | 2283 | help |
| 2284 | This driver supports the Gigabit Ethernet chips present on the |
| 2285 | Cell Processor-Based Blades from IBM. |
| 2286 | |
Zang Roy-r61911 | 5e123b8 | 2006-11-08 19:49:13 -0800 | [diff] [blame] | 2287 | config TSI108_ETH |
| 2288 | tristate "Tundra TSI108 gigabit Ethernet support" |
| 2289 | depends on TSI108_BRIDGE |
| 2290 | help |
| 2291 | This driver supports Tundra TSI108 gigabit Ethernet ports. |
| 2292 | To compile this driver as a module, choose M here: the module |
| 2293 | will be called tsi108_eth. |
| 2294 | |
Masakazu Mokuno | 02c1889 | 2007-07-05 20:11:16 +0900 | [diff] [blame] | 2295 | config GELIC_NET |
| 2296 | tristate "PS3 Gigabit Ethernet driver" |
| 2297 | depends on PPC_PS3 |
| 2298 | help |
| 2299 | This driver supports the network device on the PS3 game |
| 2300 | console. This driver has built-in support for Ethernet. |
| 2301 | |
| 2302 | To compile this driver as a module, choose M here: the |
| 2303 | module will be called ps3_gelic. |
| 2304 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2305 | config GIANFAR |
| 2306 | tristate "Gianfar Ethernet" |
Jon Loeliger | ef82a30 | 2006-06-17 17:52:55 -0500 | [diff] [blame] | 2307 | depends on 85xx || 83xx || PPC_86xx |
Andy Fleming | bb40dcb | 2005-09-23 22:54:21 -0400 | [diff] [blame] | 2308 | select PHYLIB |
Dave Jiang | bf41a7c | 2007-04-12 10:57:06 -0700 | [diff] [blame] | 2309 | select CRC32 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2310 | help |
Jon Loeliger | ef82a30 | 2006-06-17 17:52:55 -0500 | [diff] [blame] | 2311 | This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, |
| 2312 | and MPC86xx family of chips, and the FEC on the 8540. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2313 | |
| 2314 | config GFAR_NAPI |
Randy Dunlap | bf45abe | 2007-10-18 17:16:20 -0700 | [diff] [blame] | 2315 | bool "Use Rx Polling (NAPI)" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2316 | depends on GIANFAR |
| 2317 | |
Li Yang | ce973b1 | 2006-08-14 23:00:11 -0700 | [diff] [blame] | 2318 | config UCC_GETH |
Timur Tabi | 7d776cb | 2007-03-12 15:40:27 -0500 | [diff] [blame] | 2319 | tristate "Freescale QE Gigabit Ethernet" |
| 2320 | depends on QUICC_ENGINE |
Jan Altenberg | 296baae | 2007-06-01 00:46:29 -0700 | [diff] [blame] | 2321 | select PHYLIB |
Li Yang | ce973b1 | 2006-08-14 23:00:11 -0700 | [diff] [blame] | 2322 | help |
Timur Tabi | 7d776cb | 2007-03-12 15:40:27 -0500 | [diff] [blame] | 2323 | This driver supports the Gigabit Ethernet mode of the QUICC Engine, |
| 2324 | which is available on some Freescale SOCs. |
Li Yang | ce973b1 | 2006-08-14 23:00:11 -0700 | [diff] [blame] | 2325 | |
| 2326 | config UGETH_NAPI |
Randy Dunlap | bf45abe | 2007-10-18 17:16:20 -0700 | [diff] [blame] | 2327 | bool "Use Rx Polling (NAPI)" |
Li Yang | ce973b1 | 2006-08-14 23:00:11 -0700 | [diff] [blame] | 2328 | depends on UCC_GETH |
| 2329 | |
| 2330 | config UGETH_MAGIC_PACKET |
| 2331 | bool "Magic Packet detection support" |
| 2332 | depends on UCC_GETH |
| 2333 | |
| 2334 | config UGETH_FILTERING |
| 2335 | bool "Mac address filtering support" |
| 2336 | depends on UCC_GETH |
| 2337 | |
Michael Reiss | d5b9049 | 2007-04-13 01:26:19 -0500 | [diff] [blame] | 2338 | config UGETH_TX_ON_DEMAND |
| 2339 | bool "Transmit on Demand support" |
Li Yang | ce973b1 | 2006-08-14 23:00:11 -0700 | [diff] [blame] | 2340 | depends on UCC_GETH |
| 2341 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2342 | config MV643XX_ETH |
Lennert Buytenhek | 9c1bbdf | 2007-10-19 04:11:03 +0200 | [diff] [blame] | 2343 | tristate "Marvell Discovery (643XX) and Orion ethernet support" |
| 2344 | depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || ARCH_ORION |
Dale Farnsworth | cd6478c | 2006-03-03 10:01:08 -0700 | [diff] [blame] | 2345 | select MII |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2346 | help |
Lennert Buytenhek | 9c1bbdf | 2007-10-19 04:11:03 +0200 | [diff] [blame] | 2347 | This driver supports the gigabit ethernet MACs in the |
| 2348 | Marvell Discovery PPC/MIPS chipset family (MV643XX) and |
| 2349 | in the Marvell Orion ARM SoC family. |
| 2350 | |
| 2351 | Some boards that use the Discovery chipset are the Momenco |
| 2352 | Ocelot C and Jaguar ATX and Pegasos II. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2353 | |
Ron Mercer | 5a4faa8 | 2006-07-25 00:40:21 -0700 | [diff] [blame] | 2354 | config QLA3XXX |
| 2355 | tristate "QLogic QLA3XXX Network Driver Support" |
| 2356 | depends on PCI |
| 2357 | help |
| 2358 | This driver supports QLogic ISP3XXX gigabit Ethernet cards. |
| 2359 | |
| 2360 | To compile this driver as a module, choose M here: the module |
| 2361 | will be called qla3xxx. |
| 2362 | |
Jay Cliburn | f3cc28c | 2007-02-08 10:42:37 -0500 | [diff] [blame] | 2363 | config ATL1 |
| 2364 | tristate "Attansic L1 Gigabit Ethernet support (EXPERIMENTAL)" |
Jay Cliburn | a1ca14b | 2007-02-14 20:12:13 -0600 | [diff] [blame] | 2365 | depends on PCI && EXPERIMENTAL |
Jay Cliburn | f3cc28c | 2007-02-08 10:42:37 -0500 | [diff] [blame] | 2366 | select CRC32 |
| 2367 | select MII |
| 2368 | help |
| 2369 | This driver supports the Attansic L1 gigabit ethernet adapter. |
| 2370 | |
| 2371 | To compile this driver as a module, choose M here. The module |
| 2372 | will be called atl1. |
| 2373 | |
Jan Engelhardt | f30486d | 2007-05-10 22:52:56 -0700 | [diff] [blame] | 2374 | endif # NETDEV_1000 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2375 | |
| 2376 | # |
| 2377 | # 10 Gigabit Ethernet |
| 2378 | # |
| 2379 | |
Jan Engelhardt | f30486d | 2007-05-10 22:52:56 -0700 | [diff] [blame] | 2380 | menuconfig NETDEV_10000 |
| 2381 | bool "Ethernet (10000 Mbit)" |
Randy Dunlap | cbcd2a4 | 2005-07-27 13:04:35 -0700 | [diff] [blame] | 2382 | depends on !UML |
Jan Engelhardt | f30486d | 2007-05-10 22:52:56 -0700 | [diff] [blame] | 2383 | default y |
Jan Engelhardt | 06bfb7e | 2007-08-18 12:56:21 +0200 | [diff] [blame] | 2384 | ---help--- |
| 2385 | Say Y here to get to see options for 10 Gigabit Ethernet drivers. |
| 2386 | This option alone does not add any kernel code. |
| 2387 | |
| 2388 | If you say N, all options in this submenu will be skipped and disabled. |
Jan Engelhardt | f30486d | 2007-05-10 22:52:56 -0700 | [diff] [blame] | 2389 | |
| 2390 | if NETDEV_10000 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2391 | |
Christoph Lameter | 8199d3a | 2005-03-30 13:34:31 -0800 | [diff] [blame] | 2392 | config CHELSIO_T1 |
| 2393 | tristate "Chelsio 10Gb Ethernet support" |
| 2394 | depends on PCI |
Stephen Hemminger | 57834ca | 2006-12-01 16:36:19 -0800 | [diff] [blame] | 2395 | select CRC32 |
Christoph Lameter | 8199d3a | 2005-03-30 13:34:31 -0800 | [diff] [blame] | 2396 | help |
Stephen Hemminger | f1d3d38 | 2006-12-01 16:36:16 -0800 | [diff] [blame] | 2397 | This driver supports Chelsio gigabit and 10-gigabit |
| 2398 | Ethernet cards. More information about adapter features and |
| 2399 | performance tuning is in <file:Documentation/networking/cxgb.txt>. |
Christoph Lameter | 8199d3a | 2005-03-30 13:34:31 -0800 | [diff] [blame] | 2400 | |
| 2401 | For general information about Chelsio and our products, visit |
| 2402 | our website at <http://www.chelsio.com>. |
| 2403 | |
| 2404 | For customer support, please visit our customer support page at |
| 2405 | <http://www.chelsio.com/support.htm>. |
| 2406 | |
| 2407 | Please send feedback to <linux-bugs@chelsio.com>. |
| 2408 | |
| 2409 | To compile this driver as a module, choose M here: the module |
| 2410 | will be called cxgb. |
| 2411 | |
Stephen Hemminger | 352c417 | 2006-12-01 16:36:17 -0800 | [diff] [blame] | 2412 | config CHELSIO_T1_1G |
| 2413 | bool "Chelsio gigabit Ethernet support" |
| 2414 | depends on CHELSIO_T1 |
| 2415 | help |
| 2416 | Enables support for Chelsio's gigabit Ethernet PCI cards. If you |
| 2417 | are using only 10G cards say 'N' here. |
| 2418 | |
Stephen Hemminger | 7fe26a6 | 2006-12-08 11:08:33 -0800 | [diff] [blame] | 2419 | config CHELSIO_T1_NAPI |
| 2420 | bool "Use Rx Polling (NAPI)" |
| 2421 | depends on CHELSIO_T1 |
| 2422 | default y |
| 2423 | help |
| 2424 | NAPI is a driver API designed to reduce CPU and interrupt load |
| 2425 | when the driver is receiving lots of packets from the card. |
| 2426 | |
Divy Le Ray | 4d22de3 | 2007-01-18 22:04:14 -0500 | [diff] [blame] | 2427 | config CHELSIO_T3 |
Divy Le Ray | 194c1fb | 2007-03-21 19:21:00 -0700 | [diff] [blame] | 2428 | tristate "Chelsio Communications T3 10Gb Ethernet support" |
| 2429 | depends on PCI |
Divy Le Ray | 2e28396 | 2007-03-18 13:10:06 -0700 | [diff] [blame] | 2430 | select FW_LOADER |
Divy Le Ray | 194c1fb | 2007-03-21 19:21:00 -0700 | [diff] [blame] | 2431 | help |
| 2432 | This driver supports Chelsio T3-based gigabit and 10Gb Ethernet |
| 2433 | adapters. |
Divy Le Ray | 4d22de3 | 2007-01-18 22:04:14 -0500 | [diff] [blame] | 2434 | |
Divy Le Ray | 194c1fb | 2007-03-21 19:21:00 -0700 | [diff] [blame] | 2435 | For general information about Chelsio and our products, visit |
| 2436 | our website at <http://www.chelsio.com>. |
Divy Le Ray | 4d22de3 | 2007-01-18 22:04:14 -0500 | [diff] [blame] | 2437 | |
Divy Le Ray | 194c1fb | 2007-03-21 19:21:00 -0700 | [diff] [blame] | 2438 | For customer support, please visit our customer support page at |
| 2439 | <http://www.chelsio.com/support.htm>. |
Divy Le Ray | 4d22de3 | 2007-01-18 22:04:14 -0500 | [diff] [blame] | 2440 | |
Divy Le Ray | 194c1fb | 2007-03-21 19:21:00 -0700 | [diff] [blame] | 2441 | Please send feedback to <linux-bugs@chelsio.com>. |
Divy Le Ray | 4d22de3 | 2007-01-18 22:04:14 -0500 | [diff] [blame] | 2442 | |
Divy Le Ray | 194c1fb | 2007-03-21 19:21:00 -0700 | [diff] [blame] | 2443 | To compile this driver as a module, choose M here: the module |
| 2444 | will be called cxgb3. |
Divy Le Ray | 4d22de3 | 2007-01-18 22:04:14 -0500 | [diff] [blame] | 2445 | |
Jan-Bernd Themann | 7a29108 | 2006-09-13 17:44:31 +0200 | [diff] [blame] | 2446 | config EHEA |
| 2447 | tristate "eHEA Ethernet support" |
Randy Dunlap | e0d5dab | 2007-10-18 21:53:50 -0700 | [diff] [blame] | 2448 | depends on IBMEBUS && INET |
Jan-Bernd Themann | d4dc4ec | 2007-09-25 16:16:34 -0700 | [diff] [blame] | 2449 | select INET_LRO |
Jan-Bernd Themann | 7a29108 | 2006-09-13 17:44:31 +0200 | [diff] [blame] | 2450 | ---help--- |
| 2451 | This driver supports the IBM pSeries eHEA ethernet adapter. |
| 2452 | |
| 2453 | To compile the driver as a module, choose M here. The module |
| 2454 | will be called ehea. |
| 2455 | |
Auke Kok | 9a799d7 | 2007-09-15 14:07:45 -0700 | [diff] [blame] | 2456 | config IXGBE |
| 2457 | tristate "Intel(R) 10GbE PCI Express adapters support" |
| 2458 | depends on PCI |
| 2459 | ---help--- |
| 2460 | This driver supports Intel(R) 10GbE PCI Express family of |
| 2461 | adapters. For more information on how to identify your adapter, go |
| 2462 | to the Adapter & Driver ID Guide at: |
| 2463 | |
| 2464 | <http://support.intel.com/support/network/adapter/pro100/21397.htm> |
| 2465 | |
| 2466 | For general information and support, go to the Intel support |
| 2467 | website at: |
| 2468 | |
| 2469 | <http://support.intel.com> |
| 2470 | |
| 2471 | More specific information on configuring the driver is in |
| 2472 | <file:Documentation/networking/ixgbe.txt>. |
| 2473 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 2474 | To compile this driver as a module, choose M here. The module |
Auke Kok | 9a799d7 | 2007-09-15 14:07:45 -0700 | [diff] [blame] | 2475 | will be called ixgbe. |
| 2476 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2477 | config IXGB |
| 2478 | tristate "Intel(R) PRO/10GbE support" |
| 2479 | depends on PCI |
| 2480 | ---help--- |
Auke Kok | 9a799d7 | 2007-09-15 14:07:45 -0700 | [diff] [blame] | 2481 | This driver supports Intel(R) PRO/10GbE family of adapters for |
| 2482 | PCI-X type cards. For PCI-E type cards, use the "ixgbe" driver |
| 2483 | instead. For more information on how to identify your adapter, go |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2484 | to the Adapter & Driver ID Guide at: |
| 2485 | |
| 2486 | <http://support.intel.com/support/network/adapter/pro100/21397.htm> |
| 2487 | |
| 2488 | For general information and support, go to the Intel support |
| 2489 | website at: |
| 2490 | |
| 2491 | <http://support.intel.com> |
| 2492 | |
| 2493 | More specific information on configuring the driver is in |
| 2494 | <file:Documentation/networking/ixgb.txt>. |
| 2495 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 2496 | To compile this driver as a module, choose M here. The module |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2497 | will be called ixgb. |
| 2498 | |
| 2499 | config IXGB_NAPI |
| 2500 | bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" |
| 2501 | depends on IXGB && EXPERIMENTAL |
| 2502 | help |
| 2503 | NAPI is a new driver API designed to reduce CPU and interrupt load |
| 2504 | when the driver is receiving lots of packets from the card. It is |
| 2505 | still somewhat experimental and thus not yet enabled by default. |
| 2506 | |
| 2507 | If your estimated Rx load is 10kpps or more, or if the card will be |
| 2508 | deployed on potentially unfriendly networks (e.g. in a firewall), |
| 2509 | then say Y here. |
| 2510 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2511 | If in doubt, say N. |
| 2512 | |
| 2513 | config S2IO |
| 2514 | tristate "S2IO 10Gbe XFrame NIC" |
| 2515 | depends on PCI |
| 2516 | ---help--- |
| 2517 | This driver supports the 10Gbe XFrame NIC of S2IO. |
Akinobu Mita | 9eb343a | 2005-10-21 19:06:42 +0900 | [diff] [blame] | 2518 | More specific information on configuring the driver is in |
| 2519 | <file:Documentation/networking/s2io.txt>. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2520 | |
| 2521 | config S2IO_NAPI |
| 2522 | bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" |
| 2523 | depends on S2IO && EXPERIMENTAL |
| 2524 | help |
| 2525 | NAPI is a new driver API designed to reduce CPU and interrupt load |
| 2526 | when the driver is receiving lots of packets from the card. It is |
| 2527 | still somewhat experimental and thus not yet enabled by default. |
| 2528 | |
| 2529 | If your estimated Rx load is 10kpps or more, or if the card will be |
| 2530 | deployed on potentially unfriendly networks (e.g. in a firewall), |
| 2531 | then say Y here. |
| 2532 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2533 | If in doubt, say N. |
| 2534 | |
Brice Goglin | 0da34b6 | 2006-05-23 06:10:15 -0400 | [diff] [blame] | 2535 | config MYRI10GE |
| 2536 | tristate "Myricom Myri-10G Ethernet support" |
Randy Dunlap | e0d5dab | 2007-10-18 21:53:50 -0700 | [diff] [blame] | 2537 | depends on PCI && INET |
Brice Goglin | 0da34b6 | 2006-05-23 06:10:15 -0400 | [diff] [blame] | 2538 | select FW_LOADER |
| 2539 | select CRC32 |
Andrew Gallatin | 1e6e934 | 2007-09-17 11:37:42 -0700 | [diff] [blame] | 2540 | select INET_LRO |
Brice Goglin | 0da34b6 | 2006-05-23 06:10:15 -0400 | [diff] [blame] | 2541 | ---help--- |
| 2542 | This driver supports Myricom Myri-10G Dual Protocol interface in |
| 2543 | Ethernet mode. If the eeprom on your board is not recent enough, |
| 2544 | you will need a newer firmware image. |
| 2545 | You may get this image or more information, at: |
| 2546 | |
Brice Goglin | d279490 | 2006-09-05 21:58:50 -0400 | [diff] [blame] | 2547 | <http://www.myri.com/scs/download-Myri10GE.html> |
Brice Goglin | 0da34b6 | 2006-05-23 06:10:15 -0400 | [diff] [blame] | 2548 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 2549 | To compile this driver as a module, choose M here. The module |
Brice Goglin | 0da34b6 | 2006-05-23 06:10:15 -0400 | [diff] [blame] | 2550 | will be called myri10ge. |
| 2551 | |
Amit S. Kale | 3d396eb | 2006-10-21 15:33:03 -0400 | [diff] [blame] | 2552 | config NETXEN_NIC |
| 2553 | tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC" |
Randy Dunlap | 5ac3661 | 2006-11-16 21:39:11 -0800 | [diff] [blame] | 2554 | depends on PCI |
Amit S. Kale | 3d396eb | 2006-10-21 15:33:03 -0400 | [diff] [blame] | 2555 | help |
| 2556 | This enables the support for NetXen's Gigabit Ethernet card. |
| 2557 | |
David S. Miller | a3138df | 2007-10-09 01:54:01 -0700 | [diff] [blame] | 2558 | config NIU |
| 2559 | tristate "Sun Neptune 10Gbit Ethernet support" |
| 2560 | depends on PCI |
| 2561 | help |
| 2562 | This enables support for cards based upon Sun's |
| 2563 | Neptune chipset. |
| 2564 | |
Olof Johansson | f5cd787 | 2007-01-31 21:43:54 -0600 | [diff] [blame] | 2565 | config PASEMI_MAC |
| 2566 | tristate "PA Semi 1/10Gbit MAC" |
| 2567 | depends on PPC64 && PCI |
Olof Johansson | bb6e959 | 2007-05-08 00:47:54 -0500 | [diff] [blame] | 2568 | select PHYLIB |
Olof Johansson | f5cd787 | 2007-01-31 21:43:54 -0600 | [diff] [blame] | 2569 | help |
| 2570 | This driver supports the on-chip 1/10Gbit Ethernet controller on |
| 2571 | PA Semi's PWRficient line of chips. |
| 2572 | |
Roland Dreier | 225c7b1 | 2007-05-08 18:00:38 -0700 | [diff] [blame] | 2573 | config MLX4_CORE |
| 2574 | tristate |
| 2575 | depends on PCI |
| 2576 | default n |
| 2577 | |
| 2578 | config MLX4_DEBUG |
| 2579 | bool "Verbose debugging output" if (MLX4_CORE && EMBEDDED) |
Paul Mundt | f550d94 | 2007-05-10 12:50:28 +0900 | [diff] [blame] | 2580 | depends on MLX4_CORE |
Roland Dreier | 225c7b1 | 2007-05-08 18:00:38 -0700 | [diff] [blame] | 2581 | default y |
| 2582 | ---help--- |
| 2583 | This option causes debugging code to be compiled into the |
| 2584 | mlx4_core driver. The output can be turned on via the |
| 2585 | debug_level module parameter (which can also be set after |
| 2586 | the driver is loaded through sysfs). |
| 2587 | |
Andy Gospodarek | 1a348cc | 2007-09-17 18:50:36 -0700 | [diff] [blame] | 2588 | config TEHUTI |
| 2589 | tristate "Tehuti Networks 10G Ethernet" |
| 2590 | depends on PCI |
| 2591 | help |
| 2592 | Tehuti Networks 10G Ethernet NIC |
| 2593 | |
Jan Engelhardt | f30486d | 2007-05-10 22:52:56 -0700 | [diff] [blame] | 2594 | endif # NETDEV_10000 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2595 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2596 | source "drivers/net/tokenring/Kconfig" |
| 2597 | |
| 2598 | source "drivers/net/wireless/Kconfig" |
| 2599 | |
Jeff Garzik | 5b2fc49 | 2007-05-09 21:31:55 -0400 | [diff] [blame] | 2600 | source "drivers/net/usb/Kconfig" |
| 2601 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2602 | source "drivers/net/pcmcia/Kconfig" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2603 | |
| 2604 | source "drivers/net/wan/Kconfig" |
| 2605 | |
| 2606 | source "drivers/atm/Kconfig" |
| 2607 | |
| 2608 | source "drivers/s390/net/Kconfig" |
| 2609 | |
Jeremy Fitzhardinge | 0d16021 | 2007-07-17 18:37:06 -0700 | [diff] [blame] | 2610 | config XEN_NETDEV_FRONTEND |
| 2611 | tristate "Xen network device frontend driver" |
| 2612 | depends on XEN |
| 2613 | default y |
| 2614 | help |
| 2615 | The network device frontend driver allows the kernel to |
| 2616 | access network devices exported exported by a virtual |
| 2617 | machine containing a physical network device driver. The |
| 2618 | frontend driver is intended for unprivileged guest domains; |
| 2619 | if you are compiling a kernel for a Xen guest, you almost |
| 2620 | certainly want to enable this. |
| 2621 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2622 | config ISERIES_VETH |
| 2623 | tristate "iSeries Virtual Ethernet driver support" |
Randy Dunlap | cbcd2a4 | 2005-07-27 13:04:35 -0700 | [diff] [blame] | 2624 | depends on PPC_ISERIES |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2625 | |
Matt Porter | f89efd5 | 2005-09-09 12:10:10 -0700 | [diff] [blame] | 2626 | config RIONET |
| 2627 | tristate "RapidIO Ethernet over messaging driver support" |
Randy Dunlap | a81c52a | 2006-11-01 21:18:58 -0800 | [diff] [blame] | 2628 | depends on RAPIDIO |
Matt Porter | f89efd5 | 2005-09-09 12:10:10 -0700 | [diff] [blame] | 2629 | |
| 2630 | config RIONET_TX_SIZE |
| 2631 | int "Number of outbound queue entries" |
| 2632 | depends on RIONET |
| 2633 | default "128" |
| 2634 | |
| 2635 | config RIONET_RX_SIZE |
| 2636 | int "Number of inbound queue entries" |
| 2637 | depends on RIONET |
| 2638 | default "128" |
| 2639 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2640 | config FDDI |
| 2641 | bool "FDDI driver support" |
Maciej W. Rozycki | e89a2cf | 2007-02-05 16:28:27 -0800 | [diff] [blame] | 2642 | depends on (PCI || EISA || TC) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2643 | help |
| 2644 | Fiber Distributed Data Interface is a high speed local area network |
| 2645 | design; essentially a replacement for high speed Ethernet. FDDI can |
| 2646 | run over copper or fiber. If you are connected to such a network and |
| 2647 | want a driver for the FDDI card in your computer, say Y here (and |
| 2648 | then also Y to the driver for your FDDI card, below). Most people |
| 2649 | will say N. |
| 2650 | |
| 2651 | config DEFXX |
Maciej W. Rozycki | e89a2cf | 2007-02-05 16:28:27 -0800 | [diff] [blame] | 2652 | tristate "Digital DEFTA/DEFEA/DEFPA adapter support" |
| 2653 | depends on FDDI && (PCI || EISA || TC) |
| 2654 | ---help--- |
| 2655 | This is support for the DIGITAL series of TURBOchannel (DEFTA), |
| 2656 | EISA (DEFEA) and PCI (DEFPA) controllers which can connect you |
| 2657 | to a local FDDI network. |
| 2658 | |
| 2659 | To compile this driver as a module, choose M here: the module |
| 2660 | will be called defxx. If unsure, say N. |
| 2661 | |
| 2662 | config DEFXX_MMIO |
| 2663 | bool |
| 2664 | prompt "Use MMIO instead of PIO" if PCI || EISA |
| 2665 | depends on DEFXX |
| 2666 | default n if PCI || EISA |
| 2667 | default y |
| 2668 | ---help--- |
| 2669 | This instructs the driver to use EISA or PCI memory-mapped I/O |
| 2670 | (MMIO) as appropriate instead of programmed I/O ports (PIO). |
| 2671 | Enabling this gives an improvement in processing time in parts |
| 2672 | of the driver, but it may cause problems with EISA (DEFEA) |
| 2673 | adapters. TURBOchannel does not have the concept of I/O ports, |
| 2674 | so MMIO is always used for these (DEFTA) adapters. |
| 2675 | |
| 2676 | If unsure, say N. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2677 | |
| 2678 | config SKFP |
| 2679 | tristate "SysKonnect FDDI PCI support" |
| 2680 | depends on FDDI && PCI |
Akinobu Mita | bc63eb9 | 2006-12-19 13:09:08 -0800 | [diff] [blame] | 2681 | select BITREVERSE |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2682 | ---help--- |
| 2683 | Say Y here if you have a SysKonnect FDDI PCI adapter. |
| 2684 | The following adapters are supported by this driver: |
| 2685 | - SK-5521 (SK-NET FDDI-UP) |
| 2686 | - SK-5522 (SK-NET FDDI-UP DAS) |
| 2687 | - SK-5541 (SK-NET FDDI-FP) |
| 2688 | - SK-5543 (SK-NET FDDI-LP) |
| 2689 | - SK-5544 (SK-NET FDDI-LP DAS) |
| 2690 | - SK-5821 (SK-NET FDDI-UP64) |
| 2691 | - SK-5822 (SK-NET FDDI-UP64 DAS) |
| 2692 | - SK-5841 (SK-NET FDDI-FP64) |
| 2693 | - SK-5843 (SK-NET FDDI-LP64) |
| 2694 | - SK-5844 (SK-NET FDDI-LP64 DAS) |
| 2695 | - Netelligent 100 FDDI DAS Fibre SC |
| 2696 | - Netelligent 100 FDDI SAS Fibre SC |
| 2697 | - Netelligent 100 FDDI DAS UTP |
| 2698 | - Netelligent 100 FDDI SAS UTP |
| 2699 | - Netelligent 100 FDDI SAS Fibre MIC |
| 2700 | |
| 2701 | Read <file:Documentation/networking/skfp.txt> for information about |
| 2702 | the driver. |
| 2703 | |
| 2704 | Questions concerning this driver can be addressed to: |
| 2705 | <linux@syskonnect.de> |
| 2706 | |
| 2707 | To compile this driver as a module, choose M here: the module |
| 2708 | will be called skfp. This is recommended. |
| 2709 | |
| 2710 | config HIPPI |
| 2711 | bool "HIPPI driver support (EXPERIMENTAL)" |
Randy Dunlap | cbcd2a4 | 2005-07-27 13:04:35 -0700 | [diff] [blame] | 2712 | depends on EXPERIMENTAL && INET && PCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2713 | help |
| 2714 | HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and |
| 2715 | 1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI |
| 2716 | can run over copper (25m) or fiber (300m on multi-mode or 10km on |
| 2717 | single-mode). HIPPI networks are commonly used for clusters and to |
| 2718 | connect to super computers. If you are connected to a HIPPI network |
| 2719 | and have a HIPPI network card in your computer that you want to use |
| 2720 | under Linux, say Y here (you must also remember to enable the driver |
| 2721 | for your HIPPI card below). Most people will say N here. |
| 2722 | |
| 2723 | config ROADRUNNER |
| 2724 | tristate "Essential RoadRunner HIPPI PCI adapter support (EXPERIMENTAL)" |
| 2725 | depends on HIPPI && PCI |
| 2726 | help |
| 2727 | Say Y here if this is your PCI HIPPI network card. |
| 2728 | |
| 2729 | To compile this driver as a module, choose M here: the module |
| 2730 | will be called rrunner. If unsure, say N. |
| 2731 | |
| 2732 | config ROADRUNNER_LARGE_RINGS |
| 2733 | bool "Use large TX/RX rings (EXPERIMENTAL)" |
| 2734 | depends on ROADRUNNER |
| 2735 | help |
| 2736 | If you say Y here, the RoadRunner driver will preallocate up to 2 MB |
| 2737 | of additional memory to allow for fastest operation, both for |
| 2738 | transmitting and receiving. This memory cannot be used by any other |
| 2739 | kernel code or by user space programs. Say Y here only if you have |
| 2740 | the memory. |
| 2741 | |
| 2742 | config PLIP |
| 2743 | tristate "PLIP (parallel port) support" |
Randy Dunlap | cbcd2a4 | 2005-07-27 13:04:35 -0700 | [diff] [blame] | 2744 | depends on PARPORT |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2745 | ---help--- |
| 2746 | PLIP (Parallel Line Internet Protocol) is used to create a |
| 2747 | reasonably fast mini network consisting of two (or, rarely, more) |
| 2748 | local machines. A PLIP link from a Linux box is a popular means to |
| 2749 | install a Linux distribution on a machine which doesn't have a |
| 2750 | CD-ROM drive (a minimal system has to be transferred with floppies |
| 2751 | first). The kernels on both machines need to have this PLIP option |
| 2752 | enabled for this to work. |
| 2753 | |
| 2754 | The PLIP driver has two modes, mode 0 and mode 1. The parallel |
| 2755 | ports (the connectors at the computers with 25 holes) are connected |
| 2756 | with "null printer" or "Turbo Laplink" cables which can transmit 4 |
| 2757 | bits at a time (mode 0) or with special PLIP cables, to be used on |
| 2758 | bidirectional parallel ports only, which can transmit 8 bits at a |
| 2759 | time (mode 1); you can find the wiring of these cables in |
| 2760 | <file:Documentation/networking/PLIP.txt>. The cables can be up to |
| 2761 | 15m long. Mode 0 works also if one of the machines runs DOS/Windows |
| 2762 | and has some PLIP software installed, e.g. the Crynwr PLIP packet |
| 2763 | driver (<http://oak.oakland.edu/simtel.net/msdos/pktdrvr-pre.html>) |
| 2764 | and winsock or NCSA's telnet. |
| 2765 | |
| 2766 | If you want to use PLIP, say Y and read the PLIP mini-HOWTO as well |
| 2767 | as the NET-3-HOWTO, both available from |
| 2768 | <http://www.tldp.org/docs.html#howto>. Note that the PLIP |
| 2769 | protocol has been changed and this PLIP driver won't work together |
| 2770 | with the PLIP support in Linux versions 1.0.x. This option enlarges |
| 2771 | your kernel by about 8 KB. |
| 2772 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 2773 | To compile this driver as a module, choose M here. The module |
| 2774 | will be called plip. If unsure, say Y or M, in case you buy |
| 2775 | a laptop later. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2776 | |
| 2777 | config PPP |
| 2778 | tristate "PPP (point-to-point protocol) support" |
Ralf Baechle | b6e37e5 | 2006-07-14 12:15:40 +0100 | [diff] [blame] | 2779 | select SLHC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2780 | ---help--- |
| 2781 | PPP (Point to Point Protocol) is a newer and better SLIP. It serves |
| 2782 | the same purpose: sending Internet traffic over telephone (and other |
| 2783 | serial) lines. Ask your access provider if they support it, because |
| 2784 | otherwise you can't use it; most Internet access providers these |
| 2785 | days support PPP rather than SLIP. |
| 2786 | |
| 2787 | To use PPP, you need an additional program called pppd as described |
| 2788 | in the PPP-HOWTO, available at |
| 2789 | <http://www.tldp.org/docs.html#howto>. Make sure that you have |
| 2790 | the version of pppd recommended in <file:Documentation/Changes>. |
| 2791 | The PPP option enlarges your kernel by about 16 KB. |
| 2792 | |
| 2793 | There are actually two versions of PPP: the traditional PPP for |
| 2794 | asynchronous lines, such as regular analog phone lines, and |
| 2795 | synchronous PPP which can be used over digital ISDN lines for |
| 2796 | example. If you want to use PPP over phone lines or other |
| 2797 | asynchronous serial lines, you need to say Y (or M) here and also to |
| 2798 | the next option, "PPP support for async serial ports". For PPP over |
| 2799 | synchronous lines, you should say Y (or M) here and to "Support |
| 2800 | synchronous PPP", below. |
| 2801 | |
| 2802 | If you said Y to "Version information on all symbols" above, then |
| 2803 | you cannot compile the PPP driver into the kernel; you can then only |
| 2804 | compile it as a module. To compile this driver as a module, choose M |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 2805 | here. The module will be called ppp_generic. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2806 | |
| 2807 | config PPP_MULTILINK |
| 2808 | bool "PPP multilink support (EXPERIMENTAL)" |
| 2809 | depends on PPP && EXPERIMENTAL |
| 2810 | help |
| 2811 | PPP multilink is a protocol (defined in RFC 1990) which allows you |
| 2812 | to combine several (logical or physical) lines into one logical PPP |
| 2813 | connection, so that you can utilize your full bandwidth. |
| 2814 | |
| 2815 | This has to be supported at the other end as well and you need a |
| 2816 | version of the pppd daemon which understands the multilink protocol. |
| 2817 | |
| 2818 | If unsure, say N. |
| 2819 | |
| 2820 | config PPP_FILTER |
| 2821 | bool "PPP filtering" |
| 2822 | depends on PPP |
| 2823 | help |
| 2824 | Say Y here if you want to be able to filter the packets passing over |
| 2825 | PPP interfaces. This allows you to control which packets count as |
| 2826 | activity (i.e. which packets will reset the idle timer or bring up |
Jon Mason | 47c5143 | 2006-02-12 11:53:04 -0600 | [diff] [blame] | 2827 | a demand-dialed link) and which packets are to be dropped entirely. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2828 | You need to say Y here if you wish to use the pass-filter and |
| 2829 | active-filter options to pppd. |
| 2830 | |
| 2831 | If unsure, say N. |
| 2832 | |
| 2833 | config PPP_ASYNC |
| 2834 | tristate "PPP support for async serial ports" |
| 2835 | depends on PPP |
| 2836 | select CRC_CCITT |
| 2837 | ---help--- |
| 2838 | Say Y (or M) here if you want to be able to use PPP over standard |
| 2839 | asynchronous serial ports, such as COM1 or COM2 on a PC. If you use |
| 2840 | a modem (not a synchronous or ISDN modem) to contact your ISP, you |
| 2841 | need this option. |
| 2842 | |
| 2843 | To compile this driver as a module, choose M here. |
| 2844 | |
| 2845 | If unsure, say Y. |
| 2846 | |
| 2847 | config PPP_SYNC_TTY |
| 2848 | tristate "PPP support for sync tty ports" |
| 2849 | depends on PPP |
| 2850 | help |
| 2851 | Say Y (or M) here if you want to be able to use PPP over synchronous |
| 2852 | (HDLC) tty devices, such as the SyncLink adapter. These devices |
| 2853 | are often used for high-speed leased lines like T1/E1. |
| 2854 | |
| 2855 | To compile this driver as a module, choose M here. |
| 2856 | |
| 2857 | config PPP_DEFLATE |
| 2858 | tristate "PPP Deflate compression" |
| 2859 | depends on PPP |
| 2860 | select ZLIB_INFLATE |
| 2861 | select ZLIB_DEFLATE |
| 2862 | ---help--- |
| 2863 | Support for the Deflate compression method for PPP, which uses the |
| 2864 | Deflate algorithm (the same algorithm that gzip uses) to compress |
| 2865 | each PPP packet before it is sent over the wire. The machine at the |
| 2866 | other end of the PPP link (usually your ISP) has to support the |
| 2867 | Deflate compression method as well for this to be useful. Even if |
| 2868 | they don't support it, it is safe to say Y here. |
| 2869 | |
| 2870 | To compile this driver as a module, choose M here. |
| 2871 | |
| 2872 | config PPP_BSDCOMP |
| 2873 | tristate "PPP BSD-Compress compression" |
| 2874 | depends on PPP |
| 2875 | ---help--- |
| 2876 | Support for the BSD-Compress compression method for PPP, which uses |
| 2877 | the LZW compression method to compress each PPP packet before it is |
| 2878 | sent over the wire. The machine at the other end of the PPP link |
| 2879 | (usually your ISP) has to support the BSD-Compress compression |
| 2880 | method as well for this to be useful. Even if they don't support it, |
| 2881 | it is safe to say Y here. |
| 2882 | |
| 2883 | The PPP Deflate compression method ("PPP Deflate compression", |
| 2884 | above) is preferable to BSD-Compress, because it compresses better |
| 2885 | and is patent-free. |
| 2886 | |
| 2887 | Note that the BSD compression code will always be compiled as a |
| 2888 | module; it is called bsd_comp and will show up in the directory |
| 2889 | modules once you have said "make modules". If unsure, say N. |
| 2890 | |
Matt Domsch | b3f9b92 | 2005-11-08 09:40:47 -0800 | [diff] [blame] | 2891 | config PPP_MPPE |
| 2892 | tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)" |
| 2893 | depends on PPP && EXPERIMENTAL |
| 2894 | select CRYPTO |
| 2895 | select CRYPTO_SHA1 |
| 2896 | select CRYPTO_ARC4 |
Patrick McHardy | bcbaecb | 2006-10-25 16:49:36 +1000 | [diff] [blame] | 2897 | select CRYPTO_ECB |
Matt Domsch | b3f9b92 | 2005-11-08 09:40:47 -0800 | [diff] [blame] | 2898 | ---help--- |
| 2899 | Support for the MPPE Encryption protocol, as employed by the |
| 2900 | Microsoft Point-to-Point Tunneling Protocol. |
| 2901 | |
| 2902 | See http://pptpclient.sourceforge.net/ for information on |
| 2903 | configuring PPTP clients and servers to utilize this method. |
| 2904 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2905 | config PPPOE |
| 2906 | tristate "PPP over Ethernet (EXPERIMENTAL)" |
| 2907 | depends on EXPERIMENTAL && PPP |
| 2908 | help |
| 2909 | Support for PPP over Ethernet. |
| 2910 | |
| 2911 | This driver requires the latest version of pppd from the CVS |
| 2912 | repository at cvs.samba.org. Alternatively, see the |
| 2913 | RoaringPenguin package (<http://www.roaringpenguin.com/pppoe>) |
| 2914 | which contains instruction on how to use this driver (under |
| 2915 | the heading "Kernel mode PPPoE"). |
| 2916 | |
| 2917 | config PPPOATM |
| 2918 | tristate "PPP over ATM" |
| 2919 | depends on ATM && PPP |
| 2920 | help |
| 2921 | Support PPP (Point to Point Protocol) encapsulated in ATM frames. |
| 2922 | This implementation does not yet comply with section 8 of RFC2364, |
| 2923 | which can lead to bad results if the ATM peer loses state and |
| 2924 | changes its encapsulation unilaterally. |
| 2925 | |
James Chapman | 3557baa | 2007-06-27 15:49:24 -0700 | [diff] [blame] | 2926 | config PPPOL2TP |
| 2927 | tristate "PPP over L2TP (EXPERIMENTAL)" |
James Chapman | 143cf35 | 2007-07-30 18:51:48 -0700 | [diff] [blame] | 2928 | depends on EXPERIMENTAL && PPP && INET |
James Chapman | 3557baa | 2007-06-27 15:49:24 -0700 | [diff] [blame] | 2929 | help |
| 2930 | Support for PPP-over-L2TP socket family. L2TP is a protocol |
| 2931 | used by ISPs and enterprises to tunnel PPP traffic over UDP |
| 2932 | tunnels. L2TP is replacing PPTP for VPN uses. |
| 2933 | |
| 2934 | This kernel component handles only L2TP data packets: a |
| 2935 | userland daemon handles L2TP the control protocol (tunnel |
| 2936 | and session setup). One such daemon is OpenL2TP |
| 2937 | (http://openl2tp.sourceforge.net/). |
| 2938 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2939 | config SLIP |
| 2940 | tristate "SLIP (serial line) support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2941 | ---help--- |
| 2942 | Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to |
| 2943 | connect to your Internet service provider or to connect to some |
| 2944 | other local Unix box or if you want to configure your Linux box as a |
| 2945 | Slip/CSlip server for other people to dial in. SLIP (Serial Line |
| 2946 | Internet Protocol) is a protocol used to send Internet traffic over |
| 2947 | serial connections such as telephone lines or null modem cables; |
| 2948 | nowadays, the protocol PPP is more commonly used for this same |
| 2949 | purpose. |
| 2950 | |
| 2951 | Normally, your access provider has to support SLIP in order for you |
| 2952 | to be able to use it, but there is now a SLIP emulator called SLiRP |
| 2953 | around (available from |
| 2954 | <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which |
| 2955 | allows you to use SLIP over a regular dial up shell connection. If |
| 2956 | you plan to use SLiRP, make sure to say Y to CSLIP, below. The |
| 2957 | NET-3-HOWTO, available from |
| 2958 | <http://www.tldp.org/docs.html#howto>, explains how to |
| 2959 | configure SLIP. Note that you don't need this option if you just |
| 2960 | want to run term (term is a program which gives you almost full |
| 2961 | Internet connectivity if you have a regular dial up shell account on |
| 2962 | some Internet connected Unix computer. Read |
| 2963 | <http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>). SLIP |
| 2964 | support will enlarge your kernel by about 4 KB. If unsure, say N. |
| 2965 | |
Adrian Bunk | 57ce45d | 2007-11-12 21:03:58 -0800 | [diff] [blame] | 2966 | To compile this driver as a module, choose M here. The module |
| 2967 | will be called slip. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2968 | |
| 2969 | config SLIP_COMPRESSED |
| 2970 | bool "CSLIP compressed headers" |
| 2971 | depends on SLIP |
Ralf Baechle | b6e37e5 | 2006-07-14 12:15:40 +0100 | [diff] [blame] | 2972 | select SLHC |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2973 | ---help--- |
| 2974 | This protocol is faster than SLIP because it uses compression on the |
| 2975 | TCP/IP headers (not on the data itself), but it has to be supported |
| 2976 | on both ends. Ask your access provider if you are not sure and |
| 2977 | answer Y, just in case. You will still be able to use plain SLIP. If |
| 2978 | you plan to use SLiRP, the SLIP emulator (available from |
| 2979 | <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which |
| 2980 | allows you to use SLIP over a regular dial up shell connection, you |
| 2981 | definitely want to say Y here. The NET-3-HOWTO, available from |
| 2982 | <http://www.tldp.org/docs.html#howto>, explains how to configure |
| 2983 | CSLIP. This won't enlarge your kernel. |
| 2984 | |
Ralf Baechle | b6e37e5 | 2006-07-14 12:15:40 +0100 | [diff] [blame] | 2985 | config SLHC |
| 2986 | tristate |
| 2987 | help |
| 2988 | This option enables Van Jacobsen serial line header compression |
| 2989 | routines. |
| 2990 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 2991 | config SLIP_SMART |
| 2992 | bool "Keepalive and linefill" |
| 2993 | depends on SLIP |
| 2994 | help |
| 2995 | Adds additional capabilities to the SLIP driver to support the |
| 2996 | RELCOM line fill and keepalive monitoring. Ideal on poor quality |
| 2997 | analogue lines. |
| 2998 | |
| 2999 | config SLIP_MODE_SLIP6 |
| 3000 | bool "Six bit SLIP encapsulation" |
| 3001 | depends on SLIP |
| 3002 | help |
| 3003 | Just occasionally you may need to run IP over hostile serial |
| 3004 | networks that don't pass all control characters or are only seven |
| 3005 | bit. Saying Y here adds an extra mode you can use with SLIP: |
| 3006 | "slip6". In this mode, SLIP will only send normal ASCII symbols over |
| 3007 | the serial device. Naturally, this has to be supported at the other |
| 3008 | end of the link as well. It's good enough, for example, to run IP |
| 3009 | over the async ports of a Camtec JNT Pad. If unsure, say N. |
| 3010 | |
| 3011 | config NET_FC |
| 3012 | bool "Fibre Channel driver support" |
Randy Dunlap | cbcd2a4 | 2005-07-27 13:04:35 -0700 | [diff] [blame] | 3013 | depends on SCSI && PCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 3014 | help |
| 3015 | Fibre Channel is a high speed serial protocol mainly used to connect |
| 3016 | large storage devices to the computer; it is compatible with and |
| 3017 | intended to replace SCSI. |
| 3018 | |
| 3019 | If you intend to use Fibre Channel, you need to have a Fibre channel |
| 3020 | adaptor card in your computer; say Y here and to the driver for your |
| 3021 | adaptor below. You also should have said Y to "SCSI support" and |
| 3022 | "SCSI generic support". |
| 3023 | |
| 3024 | config SHAPER |
Jiri Slaby | 3b6a792 | 2006-11-06 14:34:48 -0800 | [diff] [blame] | 3025 | tristate "Traffic Shaper (OBSOLETE)" |
Randy Dunlap | cbcd2a4 | 2005-07-27 13:04:35 -0700 | [diff] [blame] | 3026 | depends on EXPERIMENTAL |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 3027 | ---help--- |
| 3028 | The traffic shaper is a virtual network device that allows you to |
| 3029 | limit the rate of outgoing data flow over some other network device. |
| 3030 | The traffic that you want to slow down can then be routed through |
| 3031 | these virtual devices. See |
| 3032 | <file:Documentation/networking/shaper.txt> for more information. |
| 3033 | |
Jiri Slaby | 3b6a792 | 2006-11-06 14:34:48 -0800 | [diff] [blame] | 3034 | An alternative to this traffic shaper are traffic schedulers which |
| 3035 | you'll get if you say Y to "QoS and/or fair queuing" in |
| 3036 | "Networking options". |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 3037 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 3038 | To compile this driver as a module, choose M here: the module |
| 3039 | will be called shaper. If unsure, say N. |
| 3040 | |
| 3041 | config NETCONSOLE |
| 3042 | tristate "Network console logging support (EXPERIMENTAL)" |
Matt Mackall | 5e43db7 | 2005-07-27 15:24:42 -0700 | [diff] [blame] | 3043 | depends on EXPERIMENTAL |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 3044 | ---help--- |
| 3045 | If you want to log kernel messages over the network, enable this. |
| 3046 | See <file:Documentation/networking/netconsole.txt> for details. |
| 3047 | |
Satyam Sharma | 0bcc181 | 2007-08-10 15:35:05 -0700 | [diff] [blame] | 3048 | config NETCONSOLE_DYNAMIC |
| 3049 | bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)" |
| 3050 | depends on NETCONSOLE && SYSFS && EXPERIMENTAL |
| 3051 | select CONFIGFS_FS |
| 3052 | help |
| 3053 | This option enables the ability to dynamically reconfigure target |
| 3054 | parameters (interface, IP addresses, port numbers, MAC addresses) |
| 3055 | at runtime through a userspace interface exported using configfs. |
| 3056 | See <file:Documentation/networking/netconsole.txt> for details. |
| 3057 | |
Randy Dunlap | 5420899 | 2005-07-18 13:45:12 -0700 | [diff] [blame] | 3058 | config NETPOLL |
| 3059 | def_bool NETCONSOLE |
| 3060 | |
Randy Dunlap | 5420899 | 2005-07-18 13:45:12 -0700 | [diff] [blame] | 3061 | config NETPOLL_TRAP |
| 3062 | bool "Netpoll traffic trapping" |
| 3063 | default n |
| 3064 | depends on NETPOLL |
| 3065 | |
| 3066 | config NET_POLL_CONTROLLER |
| 3067 | def_bool NETPOLL |
| 3068 | |
Rusty Russell | 296f96f | 2007-10-22 11:03:37 +1000 | [diff] [blame] | 3069 | config VIRTIO_NET |
| 3070 | tristate "Virtio network driver (EXPERIMENTAL)" |
| 3071 | depends on EXPERIMENTAL && VIRTIO |
| 3072 | ---help--- |
| 3073 | This is the virtual network driver for lguest. Say Y or M. |
| 3074 | |
Jan Engelhardt | d1c0a65 | 2007-06-13 12:48:53 -0700 | [diff] [blame] | 3075 | endif # NETDEVICES |