blob: af23fd6bd7952575aedd7feacb1bf8392a1261ed [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001#ifndef _AHA1740_H
2
3/* $Id$
4 *
5 * Header file for the adaptec 1740 driver for Linux
6 *
7 * With minor revisions 3/31/93
8 * Written and (C) 1992,1993 Brad McLean. See aha1740.c
9 * for more info
10 *
11 */
12
13#include <linux/types.h>
14
15#define SLOTSIZE 0x5c
16
17/* EISA configuration registers & values */
18#define HID0(base) (base + 0x0)
19#define HID1(base) (base + 0x1)
20#define HID2(base) (base + 0x2)
21#define HID3(base) (base + 0x3)
22#define EBCNTRL(base) (base + 0x4)
23#define PORTADR(base) (base + 0x40)
24#define BIOSADR(base) (base + 0x41)
25#define INTDEF(base) (base + 0x42)
26#define SCSIDEF(base) (base + 0x43)
27#define BUSDEF(base) (base + 0x44)
28#define RESV0(base) (base + 0x45)
29#define RESV1(base) (base + 0x46)
30#define RESV2(base) (base + 0x47)
31
32#define HID_MFG "ADP"
33#define HID_PRD 0
34#define HID_REV 2
35#define EBCNTRL_VALUE 1
36#define PORTADDR_ENH 0x80
37/* READ */
38#define G2INTST(base) (base + 0x56)
39#define G2STAT(base) (base + 0x57)
40#define MBOXIN0(base) (base + 0x58)
41#define MBOXIN1(base) (base + 0x59)
42#define MBOXIN2(base) (base + 0x5a)
43#define MBOXIN3(base) (base + 0x5b)
44#define G2STAT2(base) (base + 0x5c)
45
46#define G2INTST_MASK 0xf0 /* isolate the status */
47#define G2INTST_CCBGOOD 0x10 /* CCB Completed */
48#define G2INTST_CCBRETRY 0x50 /* CCB Completed with a retry */
49#define G2INTST_HARDFAIL 0x70 /* Adapter Hardware Failure */
50#define G2INTST_CMDGOOD 0xa0 /* Immediate command success */
51#define G2INTST_CCBERROR 0xc0 /* CCB Completed with error */
52#define G2INTST_ASNEVENT 0xd0 /* Asynchronous Event Notification */
53#define G2INTST_CMDERROR 0xe0 /* Immediate command error */
54
55#define G2STAT_MBXOUT 4 /* Mailbox Out Empty Bit */
56#define G2STAT_INTPEND 2 /* Interrupt Pending Bit */
57#define G2STAT_BUSY 1 /* Busy Bit (attention pending) */
58
59#define G2STAT2_READY 0 /* Host Ready Bit */
60
61/* WRITE (and ReadBack) */
62#define MBOXOUT0(base) (base + 0x50)
63#define MBOXOUT1(base) (base + 0x51)
64#define MBOXOUT2(base) (base + 0x52)
65#define MBOXOUT3(base) (base + 0x53)
66#define ATTN(base) (base + 0x54)
67#define G2CNTRL(base) (base + 0x55)
68
69#define ATTN_IMMED 0x10 /* Immediate Command */
70#define ATTN_START 0x40 /* Start CCB */
71#define ATTN_ABORT 0x50 /* Abort CCB */
72
73#define G2CNTRL_HRST 0x80 /* Hard Reset */
74#define G2CNTRL_IRST 0x40 /* Clear EISA Interrupt */
75#define G2CNTRL_HRDY 0x20 /* Sets HOST ready */
76
77/* This is used with scatter-gather */
78struct aha1740_chain {
79 u32 dataptr; /* Location of data */
80 u32 datalen; /* Size of this part of chain */
81};
82
83/* These belong in scsi.h */
84#define any2scsi(up, p) \
85(up)[0] = (((unsigned long)(p)) >> 16) ; \
86(up)[1] = (((unsigned long)(p)) >> 8); \
87(up)[2] = ((unsigned long)(p));
88
89#define scsi2int(up) ( (((long)*(up)) << 16) + (((long)(up)[1]) << 8) + ((long)(up)[2]) )
90
91#define xany2scsi(up, p) \
92(up)[0] = ((long)(p)) >> 24; \
93(up)[1] = ((long)(p)) >> 16; \
94(up)[2] = ((long)(p)) >> 8; \
95(up)[3] = ((long)(p));
96
97#define xscsi2int(up) ( (((long)(up)[0]) << 24) + (((long)(up)[1]) << 16) \
98 + (((long)(up)[2]) << 8) + ((long)(up)[3]) )
99
100#define MAX_CDB 12
101#define MAX_SENSE 14
102#define MAX_STATUS 32
103
104struct ecb { /* Enhanced Control Block 6.1 */
105 u16 cmdw; /* Command Word */
106 /* Flag Word 1 */
107 u16 cne:1, /* Control Block Chaining */
108 :6, di:1, /* Disable Interrupt */
109 :2, ses:1, /* Suppress Underrun error */
110 :1, sg:1, /* Scatter/Gather */
111 :1, dsb:1, /* Disable Status Block */
112 ars:1; /* Automatic Request Sense */
113 /* Flag Word 2 */
114 u16 lun:3, /* Logical Unit */
115 tag:1, /* Tagged Queuing */
116 tt:2, /* Tag Type */
117 nd:1, /* No Disconnect */
118 :1, dat:1, /* Data transfer - check direction */
119 dir:1, /* Direction of transfer 1 = datain */
120 st:1, /* Suppress Transfer */
121 chk:1, /* Calculate Checksum */
122 :2, rec:1,:1; /* Error Recovery */
123 u16 nil0; /* nothing */
124 u32 dataptr; /* Data or Scatter List ptr */
125 u32 datalen; /* Data or Scatter List len */
126 u32 statusptr; /* Status Block ptr */
127 u32 linkptr; /* Chain Address */
128 u32 nil1; /* nothing */
129 u32 senseptr; /* Sense Info Pointer */
130 u8 senselen; /* Sense Length */
131 u8 cdblen; /* CDB Length */
132 u16 datacheck; /* Data checksum */
133 u8 cdb[MAX_CDB]; /* CDB area */
134/* Hardware defined portion ends here, rest is driver defined */
135 u8 sense[MAX_SENSE]; /* Sense area */
136 u8 status[MAX_STATUS]; /* Status area */
137 Scsi_Cmnd *SCpnt; /* Link to the SCSI Command Block */
138 void (*done) (Scsi_Cmnd *); /* Completion Function */
139};
140
141#define AHA1740CMD_NOP 0x00 /* No OP */
142#define AHA1740CMD_INIT 0x01 /* Initiator SCSI Command */
143#define AHA1740CMD_DIAG 0x05 /* Run Diagnostic Command */
144#define AHA1740CMD_SCSI 0x06 /* Initialize SCSI */
145#define AHA1740CMD_SENSE 0x08 /* Read Sense Information */
146#define AHA1740CMD_DOWN 0x09 /* Download Firmware (yeah, I bet!) */
147#define AHA1740CMD_RINQ 0x0a /* Read Host Adapter Inquiry Data */
148#define AHA1740CMD_TARG 0x10 /* Target SCSI Command */
149
150#define AHA1740_ECBS 32
151#define AHA1740_SCATTER 16
152#define AHA1740_CMDLUN 1
153
154#endif