blob: 6db3301e7965adfbc53281405ac6220c0204a696 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/* 3c527.c: 3Com Etherlink/MC32 driver for Linux 2.4 and 2.6.
2 *
3 * (c) Copyright 1998 Red Hat Software Inc
4 * Written by Alan Cox.
5 * Further debugging by Carl Drougge.
6 * Initial SMP support by Felipe W Damasio <felipewd@terra.com.br>
7 * Heavily modified by Richard Procter <rnp@paradise.net.nz>
8 *
9 * Based on skeleton.c written 1993-94 by Donald Becker and ne2.c
10 * (for the MCA stuff) written by Wim Dumon.
11 *
12 * Thanks to 3Com for making this possible by providing me with the
13 * documentation.
14 *
15 * This software may be used and distributed according to the terms
16 * of the GNU General Public License, incorporated herein by reference.
17 *
18 */
19
20#define DRV_NAME "3c527"
21#define DRV_VERSION "0.7-SMP"
22#define DRV_RELDATE "2003/09/21"
23
24static const char *version =
25DRV_NAME ".c:v" DRV_VERSION " " DRV_RELDATE " Richard Procter <rnp@paradise.net.nz>\n";
26
27/**
28 * DOC: Traps for the unwary
29 *
30 * The diagram (Figure 1-1) and the POS summary disagree with the
31 * "Interrupt Level" section in the manual.
32 *
33 * The manual contradicts itself when describing the minimum number
34 * buffers in the 'configure lists' command.
35 * My card accepts a buffer config of 4/4.
36 *
37 * Setting the SAV BP bit does not save bad packets, but
38 * only enables RX on-card stats collection.
39 *
40 * The documentation in places seems to miss things. In actual fact
41 * I've always eventually found everything is documented, it just
42 * requires careful study.
43 *
44 * DOC: Theory Of Operation
45 *
46 * The 3com 3c527 is a 32bit MCA bus mastering adapter with a large
47 * amount of on board intelligence that housekeeps a somewhat dumber
48 * Intel NIC. For performance we want to keep the transmit queue deep
49 * as the card can transmit packets while fetching others from main
50 * memory by bus master DMA. Transmission and reception are driven by
51 * circular buffer queues.
52 *
53 * The mailboxes can be used for controlling how the card traverses
54 * its buffer rings, but are used only for inital setup in this
55 * implementation. The exec mailbox allows a variety of commands to
56 * be executed. Each command must complete before the next is
57 * executed. Primarily we use the exec mailbox for controlling the
58 * multicast lists. We have to do a certain amount of interesting
59 * hoop jumping as the multicast list changes can occur in interrupt
60 * state when the card has an exec command pending. We defer such
61 * events until the command completion interrupt.
62 *
63 * A copy break scheme (taken from 3c59x.c) is employed whereby
64 * received frames exceeding a configurable length are passed
65 * directly to the higher networking layers without incuring a copy,
66 * in what amounts to a time/space trade-off.
67 *
68 * The card also keeps a large amount of statistical information
69 * on-board. In a perfect world, these could be used safely at no
70 * cost. However, lacking information to the contrary, processing
71 * them without races would involve so much extra complexity as to
72 * make it unworthwhile to do so. In the end, a hybrid SW/HW
73 * implementation was made necessary --- see mc32_update_stats().
74 *
75 * DOC: Notes
76 *
77 * It should be possible to use two or more cards, but at this stage
78 * only by loading two copies of the same module.
79 *
80 * The on-board 82586 NIC has trouble receiving multiple
81 * back-to-back frames and so is likely to drop packets from fast
82 * senders.
83**/
84
85#include <linux/module.h>
86
87#include <linux/errno.h>
88#include <linux/netdevice.h>
89#include <linux/etherdevice.h>
90#include <linux/if_ether.h>
91#include <linux/init.h>
92#include <linux/kernel.h>
93#include <linux/types.h>
94#include <linux/fcntl.h>
95#include <linux/interrupt.h>
96#include <linux/mca-legacy.h>
97#include <linux/ioport.h>
98#include <linux/in.h>
99#include <linux/skbuff.h>
100#include <linux/slab.h>
101#include <linux/string.h>
102#include <linux/wait.h>
103#include <linux/ethtool.h>
104#include <linux/completion.h>
105#include <linux/bitops.h>
106
107#include <asm/semaphore.h>
108#include <asm/uaccess.h>
109#include <asm/system.h>
110#include <asm/io.h>
111#include <asm/dma.h>
112
113#include "3c527.h"
114
115MODULE_LICENSE("GPL");
116
117/*
118 * The name of the card. Is used for messages and in the requests for
119 * io regions, irqs and dma channels
120 */
121static const char* cardname = DRV_NAME;
122
123/* use 0 for production, 1 for verification, >2 for debug */
124#ifndef NET_DEBUG
125#define NET_DEBUG 2
126#endif
127
128#undef DEBUG_IRQ
129
130static unsigned int mc32_debug = NET_DEBUG;
131
132/* The number of low I/O ports used by the ethercard. */
133#define MC32_IO_EXTENT 8
134
135/* As implemented, values must be a power-of-2 -- 4/8/16/32 */
136#define TX_RING_LEN 32 /* Typically the card supports 37 */
137#define RX_RING_LEN 8 /* " " " */
138
139/* Copy break point, see above for details.
140 * Setting to > 1512 effectively disables this feature. */
141#define RX_COPYBREAK 200 /* Value from 3c59x.c */
142
143/* Issue the 82586 workaround command - this is for "busy lans", but
144 * basically means for all lans now days - has a performance (latency)
145 * cost, but best set. */
146static const int WORKAROUND_82586=1;
147
148/* Pointers to buffers and their on-card records */
149struct mc32_ring_desc
150{
151 volatile struct skb_header *p;
152 struct sk_buff *skb;
153};
154
155/* Information that needs to be kept for each board. */
156struct mc32_local
157{
158 int slot;
159
160 u32 base;
161 struct net_device_stats net_stats;
162 volatile struct mc32_mailbox *rx_box;
163 volatile struct mc32_mailbox *tx_box;
164 volatile struct mc32_mailbox *exec_box;
165 volatile struct mc32_stats *stats; /* Start of on-card statistics */
166 u16 tx_chain; /* Transmit list start offset */
167 u16 rx_chain; /* Receive list start offset */
168 u16 tx_len; /* Transmit list count */
169 u16 rx_len; /* Receive list count */
170
171 u16 xceiver_desired_state; /* HALTED or RUNNING */
172 u16 cmd_nonblocking; /* Thread is uninterested in command result */
173 u16 mc_reload_wait; /* A multicast load request is pending */
174 u32 mc_list_valid; /* True when the mclist is set */
175
176 struct mc32_ring_desc tx_ring[TX_RING_LEN]; /* Host Transmit ring */
177 struct mc32_ring_desc rx_ring[RX_RING_LEN]; /* Host Receive ring */
178
179 atomic_t tx_count; /* buffers left */
180 atomic_t tx_ring_head; /* index to tx en-queue end */
181 u16 tx_ring_tail; /* index to tx de-queue end */
182
183 u16 rx_ring_tail; /* index to rx de-queue end */
184
185 struct semaphore cmd_mutex; /* Serialises issuing of execute commands */
186 struct completion execution_cmd; /* Card has completed an execute command */
187 struct completion xceiver_cmd; /* Card has completed a tx or rx command */
188};
189
190/* The station (ethernet) address prefix, used for a sanity check. */
191#define SA_ADDR0 0x02
192#define SA_ADDR1 0x60
193#define SA_ADDR2 0xAC
194
195struct mca_adapters_t {
196 unsigned int id;
197 char *name;
198};
199
200static const struct mca_adapters_t mc32_adapters[] = {
201 { 0x0041, "3COM EtherLink MC/32" },
202 { 0x8EF5, "IBM High Performance Lan Adapter" },
203 { 0x0000, NULL }
204};
205
206
207/* Macros for ring index manipulations */
208static inline u16 next_rx(u16 rx) { return (rx+1)&(RX_RING_LEN-1); };
209static inline u16 prev_rx(u16 rx) { return (rx-1)&(RX_RING_LEN-1); };
210
211static inline u16 next_tx(u16 tx) { return (tx+1)&(TX_RING_LEN-1); };
212
213
214/* Index to functions, as function prototypes. */
215static int mc32_probe1(struct net_device *dev, int ioaddr);
216static int mc32_command(struct net_device *dev, u16 cmd, void *data, int len);
217static int mc32_open(struct net_device *dev);
218static void mc32_timeout(struct net_device *dev);
219static int mc32_send_packet(struct sk_buff *skb, struct net_device *dev);
220static irqreturn_t mc32_interrupt(int irq, void *dev_id, struct pt_regs *regs);
221static int mc32_close(struct net_device *dev);
222static struct net_device_stats *mc32_get_stats(struct net_device *dev);
223static void mc32_set_multicast_list(struct net_device *dev);
224static void mc32_reset_multicast_list(struct net_device *dev);
225static struct ethtool_ops netdev_ethtool_ops;
226
227static void cleanup_card(struct net_device *dev)
228{
229 struct mc32_local *lp = netdev_priv(dev);
230 unsigned slot = lp->slot;
231 mca_mark_as_unused(slot);
232 mca_set_adapter_name(slot, NULL);
233 free_irq(dev->irq, dev);
234 release_region(dev->base_addr, MC32_IO_EXTENT);
235}
236
237/**
238 * mc32_probe - Search for supported boards
239 * @unit: interface number to use
240 *
241 * Because MCA bus is a real bus and we can scan for cards we could do a
242 * single scan for all boards here. Right now we use the passed in device
243 * structure and scan for only one board. This needs fixing for modules
244 * in particular.
245 */
246
247struct net_device *__init mc32_probe(int unit)
248{
249 struct net_device *dev = alloc_etherdev(sizeof(struct mc32_local));
250 static int current_mca_slot = -1;
251 int i;
252 int err;
253
254 if (!dev)
255 return ERR_PTR(-ENOMEM);
256
257 if (unit >= 0)
258 sprintf(dev->name, "eth%d", unit);
259
260 SET_MODULE_OWNER(dev);
261
262 /* Do not check any supplied i/o locations.
263 POS registers usually don't fail :) */
264
265 /* MCA cards have POS registers.
266 Autodetecting MCA cards is extremely simple.
267 Just search for the card. */
268
269 for(i = 0; (mc32_adapters[i].name != NULL); i++) {
270 current_mca_slot =
271 mca_find_unused_adapter(mc32_adapters[i].id, 0);
272
273 if(current_mca_slot != MCA_NOTFOUND) {
274 if(!mc32_probe1(dev, current_mca_slot))
275 {
276 mca_set_adapter_name(current_mca_slot,
277 mc32_adapters[i].name);
278 mca_mark_as_used(current_mca_slot);
279 err = register_netdev(dev);
280 if (err) {
281 cleanup_card(dev);
282 free_netdev(dev);
283 dev = ERR_PTR(err);
284 }
285 return dev;
286 }
287
288 }
289 }
290 free_netdev(dev);
291 return ERR_PTR(-ENODEV);
292}
293
294/**
295 * mc32_probe1 - Check a given slot for a board and test the card
296 * @dev: Device structure to fill in
297 * @slot: The MCA bus slot being used by this card
298 *
299 * Decode the slot data and configure the card structures. Having done this we
300 * can reset the card and configure it. The card does a full self test cycle
301 * in firmware so we have to wait for it to return and post us either a
302 * failure case or some addresses we use to find the board internals.
303 */
304
305static int __init mc32_probe1(struct net_device *dev, int slot)
306{
307 static unsigned version_printed;
308 int i, err;
309 u8 POS;
310 u32 base;
311 struct mc32_local *lp = netdev_priv(dev);
312 static u16 mca_io_bases[]={
313 0x7280,0x7290,
314 0x7680,0x7690,
315 0x7A80,0x7A90,
316 0x7E80,0x7E90
317 };
318 static u32 mca_mem_bases[]={
319 0x00C0000,
320 0x00C4000,
321 0x00C8000,
322 0x00CC000,
323 0x00D0000,
324 0x00D4000,
325 0x00D8000,
326 0x00DC000
327 };
328 static char *failures[]={
329 "Processor instruction",
330 "Processor data bus",
331 "Processor data bus",
332 "Processor data bus",
333 "Adapter bus",
334 "ROM checksum",
335 "Base RAM",
336 "Extended RAM",
337 "82586 internal loopback",
338 "82586 initialisation failure",
339 "Adapter list configuration error"
340 };
341
342 /* Time to play MCA games */
343
344 if (mc32_debug && version_printed++ == 0)
345 printk(KERN_DEBUG "%s", version);
346
347 printk(KERN_INFO "%s: %s found in slot %d:", dev->name, cardname, slot);
348
349 POS = mca_read_stored_pos(slot, 2);
350
351 if(!(POS&1))
352 {
353 printk(" disabled.\n");
354 return -ENODEV;
355 }
356
357 /* Fill in the 'dev' fields. */
358 dev->base_addr = mca_io_bases[(POS>>1)&7];
359 dev->mem_start = mca_mem_bases[(POS>>4)&7];
360
361 POS = mca_read_stored_pos(slot, 4);
362 if(!(POS&1))
363 {
364 printk("memory window disabled.\n");
365 return -ENODEV;
366 }
367
368 POS = mca_read_stored_pos(slot, 5);
369
370 i=(POS>>4)&3;
371 if(i==3)
372 {
373 printk("invalid memory window.\n");
374 return -ENODEV;
375 }
376
377 i*=16384;
378 i+=16384;
379
380 dev->mem_end=dev->mem_start + i;
381
382 dev->irq = ((POS>>2)&3)+9;
383
384 if(!request_region(dev->base_addr, MC32_IO_EXTENT, cardname))
385 {
386 printk("io 0x%3lX, which is busy.\n", dev->base_addr);
387 return -EBUSY;
388 }
389
390 printk("io 0x%3lX irq %d mem 0x%lX (%dK)\n",
391 dev->base_addr, dev->irq, dev->mem_start, i/1024);
392
393
394 /* We ought to set the cache line size here.. */
395
396
397 /*
398 * Go PROM browsing
399 */
400
401 printk("%s: Address ", dev->name);
402
403 /* Retrieve and print the ethernet address. */
404 for (i = 0; i < 6; i++)
405 {
406 mca_write_pos(slot, 6, i+12);
407 mca_write_pos(slot, 7, 0);
408
409 printk(" %2.2x", dev->dev_addr[i] = mca_read_pos(slot,3));
410 }
411
412 mca_write_pos(slot, 6, 0);
413 mca_write_pos(slot, 7, 0);
414
415 POS = mca_read_stored_pos(slot, 4);
416
417 if(POS&2)
418 printk(" : BNC port selected.\n");
419 else
420 printk(" : AUI port selected.\n");
421
422 POS=inb(dev->base_addr+HOST_CTRL);
423 POS|=HOST_CTRL_ATTN|HOST_CTRL_RESET;
424 POS&=~HOST_CTRL_INTE;
425 outb(POS, dev->base_addr+HOST_CTRL);
426 /* Reset adapter */
427 udelay(100);
428 /* Reset off */
429 POS&=~(HOST_CTRL_ATTN|HOST_CTRL_RESET);
430 outb(POS, dev->base_addr+HOST_CTRL);
431
432 udelay(300);
433
434 /*
435 * Grab the IRQ
436 */
437
438 err = request_irq(dev->irq, &mc32_interrupt, SA_SHIRQ | SA_SAMPLE_RANDOM, DRV_NAME, dev);
439 if (err) {
440 release_region(dev->base_addr, MC32_IO_EXTENT);
441 printk(KERN_ERR "%s: unable to get IRQ %d.\n", DRV_NAME, dev->irq);
442 goto err_exit_ports;
443 }
444
445 memset(lp, 0, sizeof(struct mc32_local));
446 lp->slot = slot;
447
448 i=0;
449
450 base = inb(dev->base_addr);
451
452 while(base == 0xFF)
453 {
454 i++;
455 if(i == 1000)
456 {
457 printk(KERN_ERR "%s: failed to boot adapter.\n", dev->name);
458 err = -ENODEV;
459 goto err_exit_irq;
460 }
461 udelay(1000);
462 if(inb(dev->base_addr+2)&(1<<5))
463 base = inb(dev->base_addr);
464 }
465
466 if(base>0)
467 {
468 if(base < 0x0C)
469 printk(KERN_ERR "%s: %s%s.\n", dev->name, failures[base-1],
470 base<0x0A?" test failure":"");
471 else
472 printk(KERN_ERR "%s: unknown failure %d.\n", dev->name, base);
473 err = -ENODEV;
474 goto err_exit_irq;
475 }
476
477 base=0;
478 for(i=0;i<4;i++)
479 {
480 int n=0;
481
482 while(!(inb(dev->base_addr+2)&(1<<5)))
483 {
484 n++;
485 udelay(50);
486 if(n>100)
487 {
488 printk(KERN_ERR "%s: mailbox read fail (%d).\n", dev->name, i);
489 err = -ENODEV;
490 goto err_exit_irq;
491 }
492 }
493
494 base|=(inb(dev->base_addr)<<(8*i));
495 }
496
497 lp->exec_box=isa_bus_to_virt(dev->mem_start+base);
498
499 base=lp->exec_box->data[1]<<16|lp->exec_box->data[0];
500
501 lp->base = dev->mem_start+base;
502
503 lp->rx_box=isa_bus_to_virt(lp->base + lp->exec_box->data[2]);
504 lp->tx_box=isa_bus_to_virt(lp->base + lp->exec_box->data[3]);
505
506 lp->stats = isa_bus_to_virt(lp->base + lp->exec_box->data[5]);
507
508 /*
509 * Descriptor chains (card relative)
510 */
511
512 lp->tx_chain = lp->exec_box->data[8]; /* Transmit list start offset */
513 lp->rx_chain = lp->exec_box->data[10]; /* Receive list start offset */
514 lp->tx_len = lp->exec_box->data[9]; /* Transmit list count */
515 lp->rx_len = lp->exec_box->data[11]; /* Receive list count */
516
517 init_MUTEX_LOCKED(&lp->cmd_mutex);
518 init_completion(&lp->execution_cmd);
519 init_completion(&lp->xceiver_cmd);
520
521 printk("%s: Firmware Rev %d. %d RX buffers, %d TX buffers. Base of 0x%08X.\n",
522 dev->name, lp->exec_box->data[12], lp->rx_len, lp->tx_len, lp->base);
523
524 dev->open = mc32_open;
525 dev->stop = mc32_close;
526 dev->hard_start_xmit = mc32_send_packet;
527 dev->get_stats = mc32_get_stats;
528 dev->set_multicast_list = mc32_set_multicast_list;
529 dev->tx_timeout = mc32_timeout;
530 dev->watchdog_timeo = HZ*5; /* Board does all the work */
531 dev->ethtool_ops = &netdev_ethtool_ops;
532
533 return 0;
534
535err_exit_irq:
536 free_irq(dev->irq, dev);
537err_exit_ports:
538 release_region(dev->base_addr, MC32_IO_EXTENT);
539 return err;
540}
541
542
543/**
544 * mc32_ready_poll - wait until we can feed it a command
545 * @dev: The device to wait for
546 *
547 * Wait until the card becomes ready to accept a command via the
548 * command register. This tells us nothing about the completion
549 * status of any pending commands and takes very little time at all.
550 */
551
552static inline void mc32_ready_poll(struct net_device *dev)
553{
554 int ioaddr = dev->base_addr;
555 while(!(inb(ioaddr+HOST_STATUS)&HOST_STATUS_CRR));
556}
557
558
559/**
560 * mc32_command_nowait - send a command non blocking
561 * @dev: The 3c527 to issue the command to
562 * @cmd: The command word to write to the mailbox
563 * @data: A data block if the command expects one
564 * @len: Length of the data block
565 *
566 * Send a command from interrupt state. If there is a command
567 * currently being executed then we return an error of -1. It
568 * simply isn't viable to wait around as commands may be
569 * slow. This can theoretically be starved on SMP, but it's hard
570 * to see a realistic situation. We do not wait for the command
571 * to complete --- we rely on the interrupt handler to tidy up
572 * after us.
573 */
574
575static int mc32_command_nowait(struct net_device *dev, u16 cmd, void *data, int len)
576{
577 struct mc32_local *lp = netdev_priv(dev);
578 int ioaddr = dev->base_addr;
579 int ret = -1;
580
581 if (down_trylock(&lp->cmd_mutex) == 0)
582 {
583 lp->cmd_nonblocking=1;
584 lp->exec_box->mbox=0;
585 lp->exec_box->mbox=cmd;
586 memcpy((void *)lp->exec_box->data, data, len);
587 barrier(); /* the memcpy forgot the volatile so be sure */
588
589 /* Send the command */
590 mc32_ready_poll(dev);
591 outb(1<<6, ioaddr+HOST_CMD);
592
593 ret = 0;
594
595 /* Interrupt handler will signal mutex on completion */
596 }
597
598 return ret;
599}
600
601
602/**
603 * mc32_command - send a command and sleep until completion
604 * @dev: The 3c527 card to issue the command to
605 * @cmd: The command word to write to the mailbox
606 * @data: A data block if the command expects one
607 * @len: Length of the data block
608 *
609 * Sends exec commands in a user context. This permits us to wait around
610 * for the replies and also to wait for the command buffer to complete
611 * from a previous command before we execute our command. After our
612 * command completes we will attempt any pending multicast reload
613 * we blocked off by hogging the exec buffer.
614 *
615 * You feed the card a command, you wait, it interrupts you get a
616 * reply. All well and good. The complication arises because you use
617 * commands for filter list changes which come in at bh level from things
618 * like IPV6 group stuff.
619 */
620
621static int mc32_command(struct net_device *dev, u16 cmd, void *data, int len)
622{
623 struct mc32_local *lp = netdev_priv(dev);
624 int ioaddr = dev->base_addr;
625 int ret = 0;
626
627 down(&lp->cmd_mutex);
628
629 /*
630 * My Turn
631 */
632
633 lp->cmd_nonblocking=0;
634 lp->exec_box->mbox=0;
635 lp->exec_box->mbox=cmd;
636 memcpy((void *)lp->exec_box->data, data, len);
637 barrier(); /* the memcpy forgot the volatile so be sure */
638
639 mc32_ready_poll(dev);
640 outb(1<<6, ioaddr+HOST_CMD);
641
642 wait_for_completion(&lp->execution_cmd);
643
644 if(lp->exec_box->mbox&(1<<13))
645 ret = -1;
646
647 up(&lp->cmd_mutex);
648
649 /*
650 * A multicast set got blocked - try it now
651 */
652
653 if(lp->mc_reload_wait)
654 {
655 mc32_reset_multicast_list(dev);
656 }
657
658 return ret;
659}
660
661
662/**
663 * mc32_start_transceiver - tell board to restart tx/rx
664 * @dev: The 3c527 card to issue the command to
665 *
666 * This may be called from the interrupt state, where it is used
667 * to restart the rx ring if the card runs out of rx buffers.
668 *
669 * We must first check if it's ok to (re)start the transceiver. See
670 * mc32_close for details.
671 */
672
673static void mc32_start_transceiver(struct net_device *dev) {
674
675 struct mc32_local *lp = netdev_priv(dev);
676 int ioaddr = dev->base_addr;
677
678 /* Ignore RX overflow on device closure */
679 if (lp->xceiver_desired_state==HALTED)
680 return;
681
682 /* Give the card the offset to the post-EOL-bit RX descriptor */
683 mc32_ready_poll(dev);
684 lp->rx_box->mbox=0;
685 lp->rx_box->data[0]=lp->rx_ring[prev_rx(lp->rx_ring_tail)].p->next;
686 outb(HOST_CMD_START_RX, ioaddr+HOST_CMD);
687
688 mc32_ready_poll(dev);
689 lp->tx_box->mbox=0;
690 outb(HOST_CMD_RESTRT_TX, ioaddr+HOST_CMD); /* card ignores this on RX restart */
691
692 /* We are not interrupted on start completion */
693}
694
695
696/**
697 * mc32_halt_transceiver - tell board to stop tx/rx
698 * @dev: The 3c527 card to issue the command to
699 *
700 * We issue the commands to halt the card's transceiver. In fact,
701 * after some experimenting we now simply tell the card to
702 * suspend. When issuing aborts occasionally odd things happened.
703 *
704 * We then sleep until the card has notified us that both rx and
705 * tx have been suspended.
706 */
707
708static void mc32_halt_transceiver(struct net_device *dev)
709{
710 struct mc32_local *lp = netdev_priv(dev);
711 int ioaddr = dev->base_addr;
712
713 mc32_ready_poll(dev);
714 lp->rx_box->mbox=0;
715 outb(HOST_CMD_SUSPND_RX, ioaddr+HOST_CMD);
716 wait_for_completion(&lp->xceiver_cmd);
717
718 mc32_ready_poll(dev);
719 lp->tx_box->mbox=0;
720 outb(HOST_CMD_SUSPND_TX, ioaddr+HOST_CMD);
721 wait_for_completion(&lp->xceiver_cmd);
722}
723
724
725/**
726 * mc32_load_rx_ring - load the ring of receive buffers
727 * @dev: 3c527 to build the ring for
728 *
729 * This initalises the on-card and driver datastructures to
730 * the point where mc32_start_transceiver() can be called.
731 *
732 * The card sets up the receive ring for us. We are required to use the
733 * ring it provides, although the size of the ring is configurable.
734 *
735 * We allocate an sk_buff for each ring entry in turn and
736 * initalise its house-keeping info. At the same time, we read
737 * each 'next' pointer in our rx_ring array. This reduces slow
738 * shared-memory reads and makes it easy to access predecessor
739 * descriptors.
740 *
741 * We then set the end-of-list bit for the last entry so that the
742 * card will know when it has run out of buffers.
743 */
744
745static int mc32_load_rx_ring(struct net_device *dev)
746{
747 struct mc32_local *lp = netdev_priv(dev);
748 int i;
749 u16 rx_base;
750 volatile struct skb_header *p;
751
752 rx_base=lp->rx_chain;
753
754 for(i=0; i<RX_RING_LEN; i++) {
755 lp->rx_ring[i].skb=alloc_skb(1532, GFP_KERNEL);
756 if (lp->rx_ring[i].skb==NULL) {
757 for (;i>=0;i--)
758 kfree_skb(lp->rx_ring[i].skb);
759 return -ENOBUFS;
760 }
761 skb_reserve(lp->rx_ring[i].skb, 18);
762
763 p=isa_bus_to_virt(lp->base+rx_base);
764
765 p->control=0;
766 p->data=isa_virt_to_bus(lp->rx_ring[i].skb->data);
767 p->status=0;
768 p->length=1532;
769
770 lp->rx_ring[i].p=p;
771 rx_base=p->next;
772 }
773
774 lp->rx_ring[i-1].p->control |= CONTROL_EOL;
775
776 lp->rx_ring_tail=0;
777
778 return 0;
779}
780
781
782/**
783 * mc32_flush_rx_ring - free the ring of receive buffers
784 * @lp: Local data of 3c527 to flush the rx ring of
785 *
786 * Free the buffer for each ring slot. This may be called
787 * before mc32_load_rx_ring(), eg. on error in mc32_open().
788 * Requires rx skb pointers to point to a valid skb, or NULL.
789 */
790
791static void mc32_flush_rx_ring(struct net_device *dev)
792{
793 struct mc32_local *lp = netdev_priv(dev);
794 int i;
795
796 for(i=0; i < RX_RING_LEN; i++)
797 {
798 if (lp->rx_ring[i].skb) {
799 dev_kfree_skb(lp->rx_ring[i].skb);
800 lp->rx_ring[i].skb = NULL;
801 }
802 lp->rx_ring[i].p=NULL;
803 }
804}
805
806
807/**
808 * mc32_load_tx_ring - load transmit ring
809 * @dev: The 3c527 card to issue the command to
810 *
811 * This sets up the host transmit data-structures.
812 *
813 * First, we obtain from the card it's current postion in the tx
814 * ring, so that we will know where to begin transmitting
815 * packets.
816 *
817 * Then, we read the 'next' pointers from the on-card tx ring into
818 * our tx_ring array to reduce slow shared-mem reads. Finally, we
819 * intitalise the tx house keeping variables.
820 *
821 */
822
823static void mc32_load_tx_ring(struct net_device *dev)
824{
825 struct mc32_local *lp = netdev_priv(dev);
826 volatile struct skb_header *p;
827 int i;
828 u16 tx_base;
829
830 tx_base=lp->tx_box->data[0];
831
832 for(i=0 ; i<TX_RING_LEN ; i++)
833 {
834 p=isa_bus_to_virt(lp->base+tx_base);
835 lp->tx_ring[i].p=p;
836 lp->tx_ring[i].skb=NULL;
837
838 tx_base=p->next;
839 }
840
841 /* -1 so that tx_ring_head cannot "lap" tx_ring_tail */
842 /* see mc32_tx_ring */
843
844 atomic_set(&lp->tx_count, TX_RING_LEN-1);
845 atomic_set(&lp->tx_ring_head, 0);
846 lp->tx_ring_tail=0;
847}
848
849
850/**
851 * mc32_flush_tx_ring - free transmit ring
852 * @lp: Local data of 3c527 to flush the tx ring of
853 *
854 * If the ring is non-empty, zip over the it, freeing any
855 * allocated skb_buffs. The tx ring house-keeping variables are
856 * then reset. Requires rx skb pointers to point to a valid skb,
857 * or NULL.
858 */
859
860static void mc32_flush_tx_ring(struct net_device *dev)
861{
862 struct mc32_local *lp = netdev_priv(dev);
863 int i;
864
865 for (i=0; i < TX_RING_LEN; i++)
866 {
867 if (lp->tx_ring[i].skb)
868 {
869 dev_kfree_skb(lp->tx_ring[i].skb);
870 lp->tx_ring[i].skb = NULL;
871 }
872 }
873
874 atomic_set(&lp->tx_count, 0);
875 atomic_set(&lp->tx_ring_head, 0);
876 lp->tx_ring_tail=0;
877}
878
879
880/**
881 * mc32_open - handle 'up' of card
882 * @dev: device to open
883 *
884 * The user is trying to bring the card into ready state. This requires
885 * a brief dialogue with the card. Firstly we enable interrupts and then
886 * 'indications'. Without these enabled the card doesn't bother telling
887 * us what it has done. This had me puzzled for a week.
888 *
889 * We configure the number of card descriptors, then load the network
890 * address and multicast filters. Turn on the workaround mode. This
891 * works around a bug in the 82586 - it asks the firmware to do
892 * so. It has a performance (latency) hit but is needed on busy
893 * [read most] lans. We load the ring with buffers then we kick it
894 * all off.
895 */
896
897static int mc32_open(struct net_device *dev)
898{
899 int ioaddr = dev->base_addr;
900 struct mc32_local *lp = netdev_priv(dev);
901 u8 one=1;
902 u8 regs;
903 u16 descnumbuffs[2] = {TX_RING_LEN, RX_RING_LEN};
904
905 /*
906 * Interrupts enabled
907 */
908
909 regs=inb(ioaddr+HOST_CTRL);
910 regs|=HOST_CTRL_INTE;
911 outb(regs, ioaddr+HOST_CTRL);
912
913 /*
914 * Allow ourselves to issue commands
915 */
916
917 up(&lp->cmd_mutex);
918
919
920 /*
921 * Send the indications on command
922 */
923
924 mc32_command(dev, 4, &one, 2);
925
926 /*
927 * Poke it to make sure it's really dead.
928 */
929
930 mc32_halt_transceiver(dev);
931 mc32_flush_tx_ring(dev);
932
933 /*
934 * Ask card to set up on-card descriptors to our spec
935 */
936
937 if(mc32_command(dev, 8, descnumbuffs, 4)) {
938 printk("%s: %s rejected our buffer configuration!\n",
939 dev->name, cardname);
940 mc32_close(dev);
941 return -ENOBUFS;
942 }
943
944 /* Report new configuration */
945 mc32_command(dev, 6, NULL, 0);
946
947 lp->tx_chain = lp->exec_box->data[8]; /* Transmit list start offset */
948 lp->rx_chain = lp->exec_box->data[10]; /* Receive list start offset */
949 lp->tx_len = lp->exec_box->data[9]; /* Transmit list count */
950 lp->rx_len = lp->exec_box->data[11]; /* Receive list count */
951
952 /* Set Network Address */
953 mc32_command(dev, 1, dev->dev_addr, 6);
954
955 /* Set the filters */
956 mc32_set_multicast_list(dev);
957
958 if (WORKAROUND_82586) {
959 u16 zero_word=0;
960 mc32_command(dev, 0x0D, &zero_word, 2); /* 82586 bug workaround on */
961 }
962
963 mc32_load_tx_ring(dev);
964
965 if(mc32_load_rx_ring(dev))
966 {
967 mc32_close(dev);
968 return -ENOBUFS;
969 }
970
971 lp->xceiver_desired_state = RUNNING;
972
973 /* And finally, set the ball rolling... */
974 mc32_start_transceiver(dev);
975
976 netif_start_queue(dev);
977
978 return 0;
979}
980
981
982/**
983 * mc32_timeout - handle a timeout from the network layer
984 * @dev: 3c527 that timed out
985 *
986 * Handle a timeout on transmit from the 3c527. This normally means
987 * bad things as the hardware handles cable timeouts and mess for
988 * us.
989 *
990 */
991
992static void mc32_timeout(struct net_device *dev)
993{
994 printk(KERN_WARNING "%s: transmit timed out?\n", dev->name);
995 /* Try to restart the adaptor. */
996 netif_wake_queue(dev);
997}
998
999
1000/**
1001 * mc32_send_packet - queue a frame for transmit
1002 * @skb: buffer to transmit
1003 * @dev: 3c527 to send it out of
1004 *
1005 * Transmit a buffer. This normally means throwing the buffer onto
1006 * the transmit queue as the queue is quite large. If the queue is
1007 * full then we set tx_busy and return. Once the interrupt handler
1008 * gets messages telling it to reclaim transmit queue entries, we will
1009 * clear tx_busy and the kernel will start calling this again.
1010 *
1011 * We do not disable interrupts or acquire any locks; this can
1012 * run concurrently with mc32_tx_ring(), and the function itself
1013 * is serialised at a higher layer. However, similarly for the
1014 * card itself, we must ensure that we update tx_ring_head only
1015 * after we've established a valid packet on the tx ring (and
1016 * before we let the card "see" it, to prevent it racing with the
1017 * irq handler).
1018 *
1019 */
1020
1021static int mc32_send_packet(struct sk_buff *skb, struct net_device *dev)
1022{
1023 struct mc32_local *lp = netdev_priv(dev);
1024 u32 head = atomic_read(&lp->tx_ring_head);
1025
1026 volatile struct skb_header *p, *np;
1027
1028 netif_stop_queue(dev);
1029
1030 if(atomic_read(&lp->tx_count)==0) {
1031 return 1;
1032 }
1033
1034 skb = skb_padto(skb, ETH_ZLEN);
1035 if (skb == NULL) {
1036 netif_wake_queue(dev);
1037 return 0;
1038 }
1039
1040 atomic_dec(&lp->tx_count);
1041
1042 /* P is the last sending/sent buffer as a pointer */
1043 p=lp->tx_ring[head].p;
1044
1045 head = next_tx(head);
1046
1047 /* NP is the buffer we will be loading */
1048 np=lp->tx_ring[head].p;
1049
1050 /* We will need this to flush the buffer out */
1051 lp->tx_ring[head].skb=skb;
1052
1053 np->length = unlikely(skb->len < ETH_ZLEN) ? ETH_ZLEN : skb->len;
1054 np->data = isa_virt_to_bus(skb->data);
1055 np->status = 0;
1056 np->control = CONTROL_EOP | CONTROL_EOL;
1057 wmb();
1058
1059 /*
1060 * The new frame has been setup; we can now
1061 * let the interrupt handler and card "see" it
1062 */
1063
1064 atomic_set(&lp->tx_ring_head, head);
1065 p->control &= ~CONTROL_EOL;
1066
1067 netif_wake_queue(dev);
1068 return 0;
1069}
1070
1071
1072/**
1073 * mc32_update_stats - pull off the on board statistics
1074 * @dev: 3c527 to service
1075 *
1076 *
1077 * Query and reset the on-card stats. There's the small possibility
1078 * of a race here, which would result in an underestimation of
1079 * actual errors. As such, we'd prefer to keep all our stats
1080 * collection in software. As a rule, we do. However it can't be
1081 * used for rx errors and collisions as, by default, the card discards
1082 * bad rx packets.
1083 *
1084 * Setting the SAV BP in the rx filter command supposedly
1085 * stops this behaviour. However, testing shows that it only seems to
1086 * enable the collation of on-card rx statistics --- the driver
1087 * never sees an RX descriptor with an error status set.
1088 *
1089 */
1090
1091static void mc32_update_stats(struct net_device *dev)
1092{
1093 struct mc32_local *lp = netdev_priv(dev);
1094 volatile struct mc32_stats *st = lp->stats;
1095
1096 u32 rx_errors=0;
1097
1098 rx_errors+=lp->net_stats.rx_crc_errors +=st->rx_crc_errors;
1099 st->rx_crc_errors=0;
1100 rx_errors+=lp->net_stats.rx_fifo_errors +=st->rx_overrun_errors;
1101 st->rx_overrun_errors=0;
1102 rx_errors+=lp->net_stats.rx_frame_errors +=st->rx_alignment_errors;
1103 st->rx_alignment_errors=0;
1104 rx_errors+=lp->net_stats.rx_length_errors+=st->rx_tooshort_errors;
1105 st->rx_tooshort_errors=0;
1106 rx_errors+=lp->net_stats.rx_missed_errors+=st->rx_outofresource_errors;
1107 st->rx_outofresource_errors=0;
1108 lp->net_stats.rx_errors=rx_errors;
1109
1110 /* Number of packets which saw one collision */
1111 lp->net_stats.collisions+=st->dataC[10];
1112 st->dataC[10]=0;
1113
1114 /* Number of packets which saw 2--15 collisions */
1115 lp->net_stats.collisions+=st->dataC[11];
1116 st->dataC[11]=0;
1117}
1118
1119
1120/**
1121 * mc32_rx_ring - process the receive ring
1122 * @dev: 3c527 that needs its receive ring processing
1123 *
1124 *
1125 * We have received one or more indications from the card that a
1126 * receive has completed. The buffer ring thus contains dirty
1127 * entries. We walk the ring by iterating over the circular rx_ring
1128 * array, starting at the next dirty buffer (which happens to be the
1129 * one we finished up at last time around).
1130 *
1131 * For each completed packet, we will either copy it and pass it up
1132 * the stack or, if the packet is near MTU sized, we allocate
1133 * another buffer and flip the old one up the stack.
1134 *
1135 * We must succeed in keeping a buffer on the ring. If necessary we
1136 * will toss a received packet rather than lose a ring entry. Once
1137 * the first uncompleted descriptor is found, we move the
1138 * End-Of-List bit to include the buffers just processed.
1139 *
1140 */
1141
1142static void mc32_rx_ring(struct net_device *dev)
1143{
1144 struct mc32_local *lp = netdev_priv(dev);
1145 volatile struct skb_header *p;
1146 u16 rx_ring_tail;
1147 u16 rx_old_tail;
1148 int x=0;
1149
1150 rx_old_tail = rx_ring_tail = lp->rx_ring_tail;
1151
1152 do
1153 {
1154 p=lp->rx_ring[rx_ring_tail].p;
1155
1156 if(!(p->status & (1<<7))) { /* Not COMPLETED */
1157 break;
1158 }
1159 if(p->status & (1<<6)) /* COMPLETED_OK */
1160 {
1161
1162 u16 length=p->length;
1163 struct sk_buff *skb;
1164 struct sk_buff *newskb;
1165
1166 /* Try to save time by avoiding a copy on big frames */
1167
1168 if ((length > RX_COPYBREAK)
1169 && ((newskb=dev_alloc_skb(1532)) != NULL))
1170 {
1171 skb=lp->rx_ring[rx_ring_tail].skb;
1172 skb_put(skb, length);
1173
1174 skb_reserve(newskb,18);
1175 lp->rx_ring[rx_ring_tail].skb=newskb;
1176 p->data=isa_virt_to_bus(newskb->data);
1177 }
1178 else
1179 {
1180 skb=dev_alloc_skb(length+2);
1181
1182 if(skb==NULL) {
1183 lp->net_stats.rx_dropped++;
1184 goto dropped;
1185 }
1186
1187 skb_reserve(skb,2);
1188 memcpy(skb_put(skb, length),
1189 lp->rx_ring[rx_ring_tail].skb->data, length);
1190 }
1191
1192 skb->protocol=eth_type_trans(skb,dev);
1193 skb->dev=dev;
1194 dev->last_rx = jiffies;
1195 lp->net_stats.rx_packets++;
1196 lp->net_stats.rx_bytes += length;
1197 netif_rx(skb);
1198 }
1199
1200 dropped:
1201 p->length = 1532;
1202 p->status = 0;
1203
1204 rx_ring_tail=next_rx(rx_ring_tail);
1205 }
1206 while(x++<48);
1207
1208 /* If there was actually a frame to be processed, place the EOL bit */
1209 /* at the descriptor prior to the one to be filled next */
1210
1211 if (rx_ring_tail != rx_old_tail)
1212 {
1213 lp->rx_ring[prev_rx(rx_ring_tail)].p->control |= CONTROL_EOL;
1214 lp->rx_ring[prev_rx(rx_old_tail)].p->control &= ~CONTROL_EOL;
1215
1216 lp->rx_ring_tail=rx_ring_tail;
1217 }
1218}
1219
1220
1221/**
1222 * mc32_tx_ring - process completed transmits
1223 * @dev: 3c527 that needs its transmit ring processing
1224 *
1225 *
1226 * This operates in a similar fashion to mc32_rx_ring. We iterate
1227 * over the transmit ring. For each descriptor which has been
1228 * processed by the card, we free its associated buffer and note
1229 * any errors. This continues until the transmit ring is emptied
1230 * or we reach a descriptor that hasn't yet been processed by the
1231 * card.
1232 *
1233 */
1234
1235static void mc32_tx_ring(struct net_device *dev)
1236{
1237 struct mc32_local *lp = netdev_priv(dev);
1238 volatile struct skb_header *np;
1239
1240 /*
1241 * We rely on head==tail to mean 'queue empty'.
1242 * This is why lp->tx_count=TX_RING_LEN-1: in order to prevent
1243 * tx_ring_head wrapping to tail and confusing a 'queue empty'
1244 * condition with 'queue full'
1245 */
1246
1247 while (lp->tx_ring_tail != atomic_read(&lp->tx_ring_head))
1248 {
1249 u16 t;
1250
1251 t=next_tx(lp->tx_ring_tail);
1252 np=lp->tx_ring[t].p;
1253
1254 if(!(np->status & (1<<7)))
1255 {
1256 /* Not COMPLETED */
1257 break;
1258 }
1259 lp->net_stats.tx_packets++;
1260 if(!(np->status & (1<<6))) /* Not COMPLETED_OK */
1261 {
1262 lp->net_stats.tx_errors++;
1263
1264 switch(np->status&0x0F)
1265 {
1266 case 1:
1267 lp->net_stats.tx_aborted_errors++;
1268 break; /* Max collisions */
1269 case 2:
1270 lp->net_stats.tx_fifo_errors++;
1271 break;
1272 case 3:
1273 lp->net_stats.tx_carrier_errors++;
1274 break;
1275 case 4:
1276 lp->net_stats.tx_window_errors++;
1277 break; /* CTS Lost */
1278 case 5:
1279 lp->net_stats.tx_aborted_errors++;
1280 break; /* Transmit timeout */
1281 }
1282 }
1283 /* Packets are sent in order - this is
1284 basically a FIFO queue of buffers matching
1285 the card ring */
1286 lp->net_stats.tx_bytes+=lp->tx_ring[t].skb->len;
1287 dev_kfree_skb_irq(lp->tx_ring[t].skb);
1288 lp->tx_ring[t].skb=NULL;
1289 atomic_inc(&lp->tx_count);
1290 netif_wake_queue(dev);
1291
1292 lp->tx_ring_tail=t;
1293 }
1294
1295}
1296
1297
1298/**
1299 * mc32_interrupt - handle an interrupt from a 3c527
1300 * @irq: Interrupt number
1301 * @dev_id: 3c527 that requires servicing
1302 * @regs: Registers (unused)
1303 *
1304 *
1305 * An interrupt is raised whenever the 3c527 writes to the command
1306 * register. This register contains the message it wishes to send us
1307 * packed into a single byte field. We keep reading status entries
1308 * until we have processed all the control items, but simply count
1309 * transmit and receive reports. When all reports are in we empty the
1310 * transceiver rings as appropriate. This saves the overhead of
1311 * multiple command requests.
1312 *
1313 * Because MCA is level-triggered, we shouldn't miss indications.
1314 * Therefore, we needn't ask the card to suspend interrupts within
1315 * this handler. The card receives an implicit acknowledgment of the
1316 * current interrupt when we read the command register.
1317 *
1318 */
1319
1320static irqreturn_t mc32_interrupt(int irq, void *dev_id, struct pt_regs * regs)
1321{
1322 struct net_device *dev = dev_id;
1323 struct mc32_local *lp;
1324 int ioaddr, status, boguscount = 0;
1325 int rx_event = 0;
1326 int tx_event = 0;
1327
1328 if (dev == NULL) {
1329 printk(KERN_WARNING "%s: irq %d for unknown device.\n", cardname, irq);
1330 return IRQ_NONE;
1331 }
1332
1333 ioaddr = dev->base_addr;
1334 lp = netdev_priv(dev);
1335
1336 /* See whats cooking */
1337
1338 while((inb(ioaddr+HOST_STATUS)&HOST_STATUS_CWR) && boguscount++<2000)
1339 {
1340 status=inb(ioaddr+HOST_CMD);
1341
1342#ifdef DEBUG_IRQ
1343 printk("Status TX%d RX%d EX%d OV%d BC%d\n",
1344 (status&7), (status>>3)&7, (status>>6)&1,
1345 (status>>7)&1, boguscount);
1346#endif
1347
1348 switch(status&7)
1349 {
1350 case 0:
1351 break;
1352 case 6: /* TX fail */
1353 case 2: /* TX ok */
1354 tx_event = 1;
1355 break;
1356 case 3: /* Halt */
1357 case 4: /* Abort */
1358 complete(&lp->xceiver_cmd);
1359 break;
1360 default:
1361 printk("%s: strange tx ack %d\n", dev->name, status&7);
1362 }
1363 status>>=3;
1364 switch(status&7)
1365 {
1366 case 0:
1367 break;
1368 case 2: /* RX */
1369 rx_event=1;
1370 break;
1371 case 3: /* Halt */
1372 case 4: /* Abort */
1373 complete(&lp->xceiver_cmd);
1374 break;
1375 case 6:
1376 /* Out of RX buffers stat */
1377 /* Must restart rx */
1378 lp->net_stats.rx_dropped++;
1379 mc32_rx_ring(dev);
1380 mc32_start_transceiver(dev);
1381 break;
1382 default:
1383 printk("%s: strange rx ack %d\n",
1384 dev->name, status&7);
1385 }
1386 status>>=3;
1387 if(status&1)
1388 {
1389 /*
1390 * No thread is waiting: we need to tidy
1391 * up ourself.
1392 */
1393
1394 if (lp->cmd_nonblocking) {
1395 up(&lp->cmd_mutex);
1396 if (lp->mc_reload_wait)
1397 mc32_reset_multicast_list(dev);
1398 }
1399 else complete(&lp->execution_cmd);
1400 }
1401 if(status&2)
1402 {
1403 /*
1404 * We get interrupted once per
1405 * counter that is about to overflow.
1406 */
1407
1408 mc32_update_stats(dev);
1409 }
1410 }
1411
1412
1413 /*
1414 * Process the transmit and receive rings
1415 */
1416
1417 if(tx_event)
1418 mc32_tx_ring(dev);
1419
1420 if(rx_event)
1421 mc32_rx_ring(dev);
1422
1423 return IRQ_HANDLED;
1424}
1425
1426
1427/**
1428 * mc32_close - user configuring the 3c527 down
1429 * @dev: 3c527 card to shut down
1430 *
1431 * The 3c527 is a bus mastering device. We must be careful how we
1432 * shut it down. It may also be running shared interrupt so we have
1433 * to be sure to silence it properly
1434 *
1435 * We indicate that the card is closing to the rest of the
1436 * driver. Otherwise, it is possible that the card may run out
1437 * of receive buffers and restart the transceiver while we're
1438 * trying to close it.
1439 *
1440 * We abort any receive and transmits going on and then wait until
1441 * any pending exec commands have completed in other code threads.
1442 * In theory we can't get here while that is true, in practice I am
1443 * paranoid
1444 *
1445 * We turn off the interrupt enable for the board to be sure it can't
1446 * intefere with other devices.
1447 */
1448
1449static int mc32_close(struct net_device *dev)
1450{
1451 struct mc32_local *lp = netdev_priv(dev);
1452 int ioaddr = dev->base_addr;
1453
1454 u8 regs;
1455 u16 one=1;
1456
1457 lp->xceiver_desired_state = HALTED;
1458 netif_stop_queue(dev);
1459
1460 /*
1461 * Send the indications on command (handy debug check)
1462 */
1463
1464 mc32_command(dev, 4, &one, 2);
1465
1466 /* Shut down the transceiver */
1467
1468 mc32_halt_transceiver(dev);
1469
1470 /* Ensure we issue no more commands beyond this point */
1471
1472 down(&lp->cmd_mutex);
1473
1474 /* Ok the card is now stopping */
1475
1476 regs=inb(ioaddr+HOST_CTRL);
1477 regs&=~HOST_CTRL_INTE;
1478 outb(regs, ioaddr+HOST_CTRL);
1479
1480 mc32_flush_rx_ring(dev);
1481 mc32_flush_tx_ring(dev);
1482
1483 mc32_update_stats(dev);
1484
1485 return 0;
1486}
1487
1488
1489/**
1490 * mc32_get_stats - hand back stats to network layer
1491 * @dev: The 3c527 card to handle
1492 *
1493 * We've collected all the stats we can in software already. Now
1494 * it's time to update those kept on-card and return the lot.
1495 *
1496 */
1497
1498static struct net_device_stats *mc32_get_stats(struct net_device *dev)
1499{
1500 struct mc32_local *lp = netdev_priv(dev);
1501
1502 mc32_update_stats(dev);
1503 return &lp->net_stats;
1504}
1505
1506
1507/**
1508 * do_mc32_set_multicast_list - attempt to update multicasts
1509 * @dev: 3c527 device to load the list on
1510 * @retry: indicates this is not the first call.
1511 *
1512 *
1513 * Actually set or clear the multicast filter for this adaptor. The
1514 * locking issues are handled by this routine. We have to track
1515 * state as it may take multiple calls to get the command sequence
1516 * completed. We just keep trying to schedule the loads until we
1517 * manage to process them all.
1518 *
1519 * num_addrs == -1 Promiscuous mode, receive all packets
1520 *
1521 * num_addrs == 0 Normal mode, clear multicast list
1522 *
1523 * num_addrs > 0 Multicast mode, receive normal and MC packets,
1524 * and do best-effort filtering.
1525 *
1526 * See mc32_update_stats() regards setting the SAV BP bit.
1527 *
1528 */
1529
1530static void do_mc32_set_multicast_list(struct net_device *dev, int retry)
1531{
1532 struct mc32_local *lp = netdev_priv(dev);
1533 u16 filt = (1<<2); /* Save Bad Packets, for stats purposes */
1534
1535 if (dev->flags&IFF_PROMISC)
1536 /* Enable promiscuous mode */
1537 filt |= 1;
1538 else if((dev->flags&IFF_ALLMULTI) || dev->mc_count > 10)
1539 {
1540 dev->flags|=IFF_PROMISC;
1541 filt |= 1;
1542 }
1543 else if(dev->mc_count)
1544 {
1545 unsigned char block[62];
1546 unsigned char *bp;
1547 struct dev_mc_list *dmc=dev->mc_list;
1548
1549 int i;
1550
1551 if(retry==0)
1552 lp->mc_list_valid = 0;
1553 if(!lp->mc_list_valid)
1554 {
1555 block[1]=0;
1556 block[0]=dev->mc_count;
1557 bp=block+2;
1558
1559 for(i=0;i<dev->mc_count;i++)
1560 {
1561 memcpy(bp, dmc->dmi_addr, 6);
1562 bp+=6;
1563 dmc=dmc->next;
1564 }
1565 if(mc32_command_nowait(dev, 2, block, 2+6*dev->mc_count)==-1)
1566 {
1567 lp->mc_reload_wait = 1;
1568 return;
1569 }
1570 lp->mc_list_valid=1;
1571 }
1572 }
1573
1574 if(mc32_command_nowait(dev, 0, &filt, 2)==-1)
1575 {
1576 lp->mc_reload_wait = 1;
1577 }
1578 else {
1579 lp->mc_reload_wait = 0;
1580 }
1581}
1582
1583
1584/**
1585 * mc32_set_multicast_list - queue multicast list update
1586 * @dev: The 3c527 to use
1587 *
1588 * Commence loading the multicast list. This is called when the kernel
1589 * changes the lists. It will override any pending list we are trying to
1590 * load.
1591 */
1592
1593static void mc32_set_multicast_list(struct net_device *dev)
1594{
1595 do_mc32_set_multicast_list(dev,0);
1596}
1597
1598
1599/**
1600 * mc32_reset_multicast_list - reset multicast list
1601 * @dev: The 3c527 to use
1602 *
1603 * Attempt the next step in loading the multicast lists. If this attempt
1604 * fails to complete then it will be scheduled and this function called
1605 * again later from elsewhere.
1606 */
1607
1608static void mc32_reset_multicast_list(struct net_device *dev)
1609{
1610 do_mc32_set_multicast_list(dev,1);
1611}
1612
1613static void netdev_get_drvinfo(struct net_device *dev,
1614 struct ethtool_drvinfo *info)
1615{
1616 strcpy(info->driver, DRV_NAME);
1617 strcpy(info->version, DRV_VERSION);
1618 sprintf(info->bus_info, "MCA 0x%lx", dev->base_addr);
1619}
1620
1621static u32 netdev_get_msglevel(struct net_device *dev)
1622{
1623 return mc32_debug;
1624}
1625
1626static void netdev_set_msglevel(struct net_device *dev, u32 level)
1627{
1628 mc32_debug = level;
1629}
1630
1631static struct ethtool_ops netdev_ethtool_ops = {
1632 .get_drvinfo = netdev_get_drvinfo,
1633 .get_msglevel = netdev_get_msglevel,
1634 .set_msglevel = netdev_set_msglevel,
1635};
1636
1637#ifdef MODULE
1638
1639static struct net_device *this_device;
1640
1641/**
1642 * init_module - entry point
1643 *
1644 * Probe and locate a 3c527 card. This really should probe and locate
1645 * all the 3c527 cards in the machine not just one of them. Yes you can
1646 * insmod multiple modules for now but it's a hack.
1647 */
1648
1649int init_module(void)
1650{
1651 this_device = mc32_probe(-1);
1652 if (IS_ERR(this_device))
1653 return PTR_ERR(this_device);
1654 return 0;
1655}
1656
1657/**
1658 * cleanup_module - free resources for an unload
1659 *
1660 * Unloading time. We release the MCA bus resources and the interrupt
1661 * at which point everything is ready to unload. The card must be stopped
1662 * at this point or we would not have been called. When we unload we
1663 * leave the card stopped but not totally shut down. When the card is
1664 * initialized it must be rebooted or the rings reloaded before any
1665 * transmit operations are allowed to start scribbling into memory.
1666 */
1667
1668void cleanup_module(void)
1669{
1670 unregister_netdev(this_device);
1671 cleanup_card(this_device);
1672 free_netdev(this_device);
1673}
1674
1675#endif /* MODULE */