blob: cbb9f4321f583a17469a42886bfda4d9ca96ae76 [file] [log] [blame]
.\" -*- nroff -*-
.TH BADBLOCKS 8 "@E2FSPROGS_MONTH@ @E2FSPROGS_YEAR@" "E2fsprogs version @E2FSPROGS_VERSION@"
.SH NAME
badblocks \- search a device for bad blocks
.SH SYNOPSIS
.B badblocks
[
.B \-svwnf
]
[
.B \-b
.I block-size
]
[
.B \-c
.I blocks_at_once
]
[
.B \-i
.I input_file
]
[
.B \-o
.I output_file
]
[
.B \-p
.I num_passes
]
.I device
[
.I last-block
] [
.I start-block
]
.SH DESCRIPTION
.B badblocks
is used to search for bad blocks on a device (usually a disk partition).
.I device
is the special file corresponding to the device (e.g
.IR /dev/hdc1 ).
.I last-block
is the last block to be checked; if it is not specified, the last block
on the device is used as a default.
.I start-block
is an optional parameter specifying the starting block number
for the test, which allows the testing to start in the middle of the
disk. If it is not specified the first block on the disk is used as a default.
.SH OPTIONS
.TP
.BI \-b " block-size"
Specify the size of blocks in bytes.
.TP
.BI \-c " number of blocks"
is the number of blocks which are tested at a time. The default is 16.
Increasing this number will increase the efficiency of
.B badblocks
but also will increase its memory usage.
.B Badblocks
needs memory proportional to the number of blocks tested at once, in
read-only mode, proportional to twice that number in read-write mode,
and proportional to three times that number in non-destructive read-write
mode. If you set the number-of-blocks parameter to too high a value,
.B badblocks
will exit almost immediately with an out-of-memory error "while allocating
buffers". If you set it too low, however, for a non-destructive-write-mode
test, then it's possble for questionable blocks on an unreliable
hard drive to be hidden by the effects of the hard disk track buffer.
.TP
.B \-f
Normally, badblocks will refuse to do a read/write or a non-destructive
test on a device which is mounted, since this can cause the system to
potentially crash. This can be overriden using the
.B \-
flag, but this should not be done under normal circumstances. The only time
when this option might be safe is if the /etc/mtab file is incorrect, and
the device really isn't mounted.
.TP
.BI \-i " input_file"
Read a list of already existing known bad blocks.
.B Badblocks
will skip testing these blocks since they are known to be bad. If
.I input_file
is specified as "-", the list will be read from the standard input.
Blocks listed in this list will be omitted from the list of
.I new
bad blocks produced on the standard output or in the output file.
The
.B \-b
option of
.BR dumpe2fs (8)
can be used to retrieve the list of blocks currently marked bad on
an existing filesystem, in a format suitable for use with this option.
.TP
.BI \-o " output_file"
Write the list of bad blocks to the specified file. Without this option,
.B badblocks
displays the list on its standard output. The format of this file is suitable
for use by the
.
.B \-l
option in
.BR e2fsck (8)
or
.BR mke2fs (8).
.TP
.BI \-p " num_passes"
Repeat scanning the disk until there are no new blocks discovered in
num_passes consecutive scans of the disk.
Default is 0, meaning
.B badblocks
will exit after the first pass.
.TP
.B \-n
Use non-destructive read-write mode. By default only a non-destructive
read-only test is done. This option must not be combined with the
.B \-w
option, as they are mutually exclusive.
.TP
.B \-s
Show the progress of the scan by writing out the block numbers as they
are checked.
.TP
.B \-v
Verbose mode.
.TP
.B \-w
Use write-mode test. With this option,
.B badblocks
scans for bad blocks by writing some patterns (0xaa, 0x55, 0xff, 0x00) on
every block of the device, reading every block and comparing the contents.
This option may not be compiled with the
.B \-n
option, as they are mutually exclusive.
.SH WARNING
Never use the
.B \-w
option on an device containing an existing file system.
This option erases data! If you want to do write-mode testing on
an existing file system, use the
.B \-n
option instead. It is slower, but it will preserve your data.
.SH AUTHOR
.B badblocks
was written by Remy Card <Remy.Card@linux.org>. Current maintainer is
Theodore Ts'o <tytso@alum.mit.edu>. Non-destructive read/write test
implemented by David Beattie <dbeattie@softhome.net>.
.SH AVAILABILITY
.B badblocks
is part of the e2fsprogs package and is available from
http://e2fsprogs.sourceforge.net.
.SH SEE ALSO
.BR e2fsck (8),
.BR mke2fs (8)