| //===-- DNBArchImpl.cpp -----------------------------------------*- C++ -*-===// |
| // |
| // The LLVM Compiler Infrastructure |
| // |
| // This file is distributed under the University of Illinois Open Source |
| // License. See LICENSE.TXT for details. |
| // |
| //===----------------------------------------------------------------------===// |
| // |
| // Created by Greg Clayton on 6/25/07. |
| // |
| //===----------------------------------------------------------------------===// |
| |
| #if defined (__arm__) |
| |
| #include "MacOSX/arm/DNBArchImpl.h" |
| #include "MacOSX/MachProcess.h" |
| #include "MacOSX/MachThread.h" |
| #include "DNBBreakpoint.h" |
| #include "DNBLog.h" |
| #include "DNBRegisterInfo.h" |
| #include "DNB.h" |
| #include "ARM_GCC_Registers.h" |
| #include "ARM_DWARF_Registers.h" |
| |
| #include <sys/sysctl.h> |
| |
| // BCR address match type |
| #define BCR_M_IMVA_MATCH ((uint32_t)(0u << 21)) |
| #define BCR_M_CONTEXT_ID_MATCH ((uint32_t)(1u << 21)) |
| #define BCR_M_IMVA_MISMATCH ((uint32_t)(2u << 21)) |
| #define BCR_M_RESERVED ((uint32_t)(3u << 21)) |
| |
| // Link a BVR/BCR or WVR/WCR pair to another |
| #define E_ENABLE_LINKING ((uint32_t)(1u << 20)) |
| |
| // Byte Address Select |
| #define BAS_IMVA_PLUS_0 ((uint32_t)(1u << 5)) |
| #define BAS_IMVA_PLUS_1 ((uint32_t)(1u << 6)) |
| #define BAS_IMVA_PLUS_2 ((uint32_t)(1u << 7)) |
| #define BAS_IMVA_PLUS_3 ((uint32_t)(1u << 8)) |
| #define BAS_IMVA_0_1 ((uint32_t)(3u << 5)) |
| #define BAS_IMVA_2_3 ((uint32_t)(3u << 7)) |
| #define BAS_IMVA_ALL ((uint32_t)(0xfu << 5)) |
| |
| // Break only in priveleged or user mode |
| #define S_RSVD ((uint32_t)(0u << 1)) |
| #define S_PRIV ((uint32_t)(1u << 1)) |
| #define S_USER ((uint32_t)(2u << 1)) |
| #define S_PRIV_USER ((S_PRIV) | (S_USER)) |
| |
| #define BCR_ENABLE ((uint32_t)(1u)) |
| #define WCR_ENABLE ((uint32_t)(1u)) |
| |
| // Watchpoint load/store |
| #define WCR_LOAD ((uint32_t)(1u << 3)) |
| #define WCR_STORE ((uint32_t)(1u << 4)) |
| |
| // Definitions for the Debug Status and Control Register fields: |
| // [5:2] => Method of debug entry |
| //#define WATCHPOINT_OCCURRED ((uint32_t)(2u)) |
| // I'm seeing this, instead. |
| #define WATCHPOINT_OCCURRED ((uint32_t)(10u)) |
| |
| static const uint8_t g_arm_breakpoint_opcode[] = { 0xFE, 0xDE, 0xFF, 0xE7 }; |
| static const uint8_t g_thumb_breakpooint_opcode[] = { 0xFE, 0xDE }; |
| |
| // ARM constants used during decoding |
| #define REG_RD 0 |
| #define LDM_REGLIST 1 |
| #define PC_REG 15 |
| #define PC_REGLIST_BIT 0x8000 |
| |
| // ARM conditions |
| #define COND_EQ 0x0 |
| #define COND_NE 0x1 |
| #define COND_CS 0x2 |
| #define COND_HS 0x2 |
| #define COND_CC 0x3 |
| #define COND_LO 0x3 |
| #define COND_MI 0x4 |
| #define COND_PL 0x5 |
| #define COND_VS 0x6 |
| #define COND_VC 0x7 |
| #define COND_HI 0x8 |
| #define COND_LS 0x9 |
| #define COND_GE 0xA |
| #define COND_LT 0xB |
| #define COND_GT 0xC |
| #define COND_LE 0xD |
| #define COND_AL 0xE |
| #define COND_UNCOND 0xF |
| |
| #define MASK_CPSR_T (1u << 5) |
| #define MASK_CPSR_J (1u << 24) |
| |
| #define MNEMONIC_STRING_SIZE 32 |
| #define OPERAND_STRING_SIZE 128 |
| |
| |
| void |
| DNBArchMachARM::Initialize() |
| { |
| DNBArchPluginInfo arch_plugin_info = |
| { |
| CPU_TYPE_ARM, |
| DNBArchMachARM::Create, |
| DNBArchMachARM::GetRegisterSetInfo, |
| DNBArchMachARM::SoftwareBreakpointOpcode |
| }; |
| |
| // Register this arch plug-in with the main protocol class |
| DNBArchProtocol::RegisterArchPlugin (arch_plugin_info); |
| } |
| |
| |
| DNBArchProtocol * |
| DNBArchMachARM::Create (MachThread *thread) |
| { |
| DNBArchMachARM *obj = new DNBArchMachARM (thread); |
| return obj; |
| } |
| |
| const uint8_t * const |
| DNBArchMachARM::SoftwareBreakpointOpcode (nub_size_t byte_size) |
| { |
| switch (byte_size) |
| { |
| case 2: return g_thumb_breakpooint_opcode; |
| case 4: return g_arm_breakpoint_opcode; |
| } |
| return NULL; |
| } |
| |
| uint32_t |
| DNBArchMachARM::GetCPUType() |
| { |
| return CPU_TYPE_ARM; |
| } |
| |
| uint64_t |
| DNBArchMachARM::GetPC(uint64_t failValue) |
| { |
| // Get program counter |
| if (GetGPRState(false) == KERN_SUCCESS) |
| return m_state.context.gpr.__pc; |
| return failValue; |
| } |
| |
| kern_return_t |
| DNBArchMachARM::SetPC(uint64_t value) |
| { |
| // Get program counter |
| kern_return_t err = GetGPRState(false); |
| if (err == KERN_SUCCESS) |
| { |
| m_state.context.gpr.__pc = value; |
| err = SetGPRState(); |
| } |
| return err == KERN_SUCCESS; |
| } |
| |
| uint64_t |
| DNBArchMachARM::GetSP(uint64_t failValue) |
| { |
| // Get stack pointer |
| if (GetGPRState(false) == KERN_SUCCESS) |
| return m_state.context.gpr.__sp; |
| return failValue; |
| } |
| |
| kern_return_t |
| DNBArchMachARM::GetGPRState(bool force) |
| { |
| int set = e_regSetGPR; |
| // Check if we have valid cached registers |
| if (!force && m_state.GetError(set, Read) == KERN_SUCCESS) |
| return KERN_SUCCESS; |
| |
| // Read the registers from our thread |
| mach_msg_type_number_t count = ARM_THREAD_STATE_COUNT; |
| kern_return_t kret = ::thread_get_state(m_thread->MachPortNumber(), ARM_THREAD_STATE, (thread_state_t)&m_state.context.gpr, &count); |
| uint32_t *r = &m_state.context.gpr.__r[0]; |
| DNBLogThreadedIf(LOG_THREAD, "thread_get_state(0x%4.4x, %u, &gpr, %u) => 0x%8.8x (count = %u) regs r0=%8.8x r1=%8.8x r2=%8.8x r3=%8.8x r4=%8.8x r5=%8.8x r6=%8.8x r7=%8.8x r8=%8.8x r9=%8.8x r10=%8.8x r11=%8.8x s12=%8.8x sp=%8.8x lr=%8.8x pc=%8.8x cpsr=%8.8x", |
| m_thread->MachPortNumber(), |
| ARM_THREAD_STATE, |
| ARM_THREAD_STATE_COUNT, |
| kret, |
| count, |
| r[0], |
| r[1], |
| r[2], |
| r[3], |
| r[4], |
| r[5], |
| r[6], |
| r[7], |
| r[8], |
| r[9], |
| r[10], |
| r[11], |
| r[12], |
| r[13], |
| r[14], |
| r[15], |
| r[16]); |
| m_state.SetError(set, Read, kret); |
| return kret; |
| } |
| |
| kern_return_t |
| DNBArchMachARM::GetVFPState(bool force) |
| { |
| int set = e_regSetVFP; |
| // Check if we have valid cached registers |
| if (!force && m_state.GetError(set, Read) == KERN_SUCCESS) |
| return KERN_SUCCESS; |
| |
| // Read the registers from our thread |
| mach_msg_type_number_t count = ARM_VFP_STATE_COUNT; |
| kern_return_t kret = ::thread_get_state(m_thread->MachPortNumber(), ARM_VFP_STATE, (thread_state_t)&m_state.context.vfp, &count); |
| if (DNBLogEnabledForAny (LOG_THREAD)) |
| { |
| uint32_t *r = &m_state.context.vfp.__r[0]; |
| DNBLogThreaded ("thread_get_state(0x%4.4x, %u, &gpr, %u) => 0x%8.8x (count => %u)", |
| m_thread->MachPortNumber(), |
| ARM_THREAD_STATE, |
| ARM_THREAD_STATE_COUNT, |
| kret, |
| count); |
| DNBLogThreaded(" s0=%8.8x s1=%8.8x s2=%8.8x s3=%8.8x s4=%8.8x s5=%8.8x s6=%8.8x s7=%8.8x",r[ 0],r[ 1],r[ 2],r[ 3],r[ 4],r[ 5],r[ 6],r[ 7]); |
| DNBLogThreaded(" s8=%8.8x s9=%8.8x s10=%8.8x s11=%8.8x s12=%8.8x s13=%8.8x s14=%8.8x s15=%8.8x",r[ 8],r[ 9],r[10],r[11],r[12],r[13],r[14],r[15]); |
| DNBLogThreaded(" s16=%8.8x s17=%8.8x s18=%8.8x s19=%8.8x s20=%8.8x s21=%8.8x s22=%8.8x s23=%8.8x",r[16],r[17],r[18],r[19],r[20],r[21],r[22],r[23]); |
| DNBLogThreaded(" s24=%8.8x s25=%8.8x s26=%8.8x s27=%8.8x s28=%8.8x s29=%8.8x s30=%8.8x s31=%8.8x",r[24],r[25],r[26],r[27],r[28],r[29],r[30],r[31]); |
| DNBLogThreaded(" s32=%8.8x s33=%8.8x s34=%8.8x s35=%8.8x s36=%8.8x s37=%8.8x s38=%8.8x s39=%8.8x",r[32],r[33],r[34],r[35],r[36],r[37],r[38],r[39]); |
| DNBLogThreaded(" s40=%8.8x s41=%8.8x s42=%8.8x s43=%8.8x s44=%8.8x s45=%8.8x s46=%8.8x s47=%8.8x",r[40],r[41],r[42],r[43],r[44],r[45],r[46],r[47]); |
| DNBLogThreaded(" s48=%8.8x s49=%8.8x s50=%8.8x s51=%8.8x s52=%8.8x s53=%8.8x s54=%8.8x s55=%8.8x",r[48],r[49],r[50],r[51],r[52],r[53],r[54],r[55]); |
| DNBLogThreaded(" s56=%8.8x s57=%8.8x s58=%8.8x s59=%8.8x s60=%8.8x s61=%8.8x s62=%8.8x s63=%8.8x fpscr=%8.8x",r[56],r[57],r[58],r[59],r[60],r[61],r[62],r[63],r[64]); |
| } |
| m_state.SetError(set, Read, kret); |
| return kret; |
| } |
| |
| kern_return_t |
| DNBArchMachARM::GetEXCState(bool force) |
| { |
| int set = e_regSetEXC; |
| // Check if we have valid cached registers |
| if (!force && m_state.GetError(set, Read) == KERN_SUCCESS) |
| return KERN_SUCCESS; |
| |
| // Read the registers from our thread |
| mach_msg_type_number_t count = ARM_EXCEPTION_STATE_COUNT; |
| kern_return_t kret = ::thread_get_state(m_thread->MachPortNumber(), ARM_EXCEPTION_STATE, (thread_state_t)&m_state.context.exc, &count); |
| m_state.SetError(set, Read, kret); |
| return kret; |
| } |
| |
| static void |
| DumpDBGState(const DNBArchMachARM::DBG& dbg) |
| { |
| uint32_t i = 0; |
| for (i=0; i<16; i++) { |
| DNBLogThreadedIf(LOG_STEP, "BVR%-2u/BCR%-2u = { 0x%8.8x, 0x%8.8x } WVR%-2u/WCR%-2u = { 0x%8.8x, 0x%8.8x }", |
| i, i, dbg.__bvr[i], dbg.__bcr[i], |
| i, i, dbg.__wvr[i], dbg.__wcr[i]); |
| } |
| } |
| |
| kern_return_t |
| DNBArchMachARM::GetDBGState(bool force) |
| { |
| int set = e_regSetDBG; |
| |
| // Check if we have valid cached registers |
| if (!force && m_state.GetError(set, Read) == KERN_SUCCESS) |
| return KERN_SUCCESS; |
| |
| // Read the registers from our thread |
| mach_msg_type_number_t count = ARM_DEBUG_STATE_COUNT; |
| kern_return_t kret = ::thread_get_state(m_thread->MachPortNumber(), ARM_DEBUG_STATE, (thread_state_t)&m_state.dbg, &count); |
| m_state.SetError(set, Read, kret); |
| return kret; |
| } |
| |
| kern_return_t |
| DNBArchMachARM::SetGPRState() |
| { |
| int set = e_regSetGPR; |
| kern_return_t kret = ::thread_set_state(m_thread->MachPortNumber(), ARM_THREAD_STATE, (thread_state_t)&m_state.context.gpr, ARM_THREAD_STATE_COUNT); |
| m_state.SetError(set, Write, kret); // Set the current write error for this register set |
| m_state.InvalidateRegisterSetState(set); // Invalidate the current register state in case registers are read back differently |
| return kret; // Return the error code |
| } |
| |
| kern_return_t |
| DNBArchMachARM::SetVFPState() |
| { |
| int set = e_regSetVFP; |
| kern_return_t kret = ::thread_set_state (m_thread->MachPortNumber(), ARM_VFP_STATE, (thread_state_t)&m_state.context.vfp, ARM_VFP_STATE_COUNT); |
| m_state.SetError(set, Write, kret); // Set the current write error for this register set |
| m_state.InvalidateRegisterSetState(set); // Invalidate the current register state in case registers are read back differently |
| return kret; // Return the error code |
| } |
| |
| kern_return_t |
| DNBArchMachARM::SetEXCState() |
| { |
| int set = e_regSetEXC; |
| kern_return_t kret = ::thread_set_state (m_thread->MachPortNumber(), ARM_EXCEPTION_STATE, (thread_state_t)&m_state.context.exc, ARM_EXCEPTION_STATE_COUNT); |
| m_state.SetError(set, Write, kret); // Set the current write error for this register set |
| m_state.InvalidateRegisterSetState(set); // Invalidate the current register state in case registers are read back differently |
| return kret; // Return the error code |
| } |
| |
| kern_return_t |
| DNBArchMachARM::SetDBGState(bool also_set_on_task) |
| { |
| int set = e_regSetDBG; |
| kern_return_t kret = ::thread_set_state (m_thread->MachPortNumber(), ARM_DEBUG_STATE, (thread_state_t)&m_state.dbg, ARM_DEBUG_STATE_COUNT); |
| if (also_set_on_task) |
| { |
| kern_return_t task_kret = ::task_set_state (m_thread->Process()->Task().TaskPort(), ARM_DEBUG_STATE, (thread_state_t)&m_state.dbg, ARM_DEBUG_STATE_COUNT); |
| if (task_kret != KERN_SUCCESS) |
| DNBLogThreadedIf(LOG_WATCHPOINTS, "DNBArchMachARM::SetDBGState failed to set debug control register state: 0x%8.8x.", kret); |
| } |
| m_state.SetError(set, Write, kret); // Set the current write error for this register set |
| m_state.InvalidateRegisterSetState(set); // Invalidate the current register state in case registers are read back differently |
| return kret; // Return the error code |
| } |
| |
| void |
| DNBArchMachARM::ThreadWillResume() |
| { |
| // Do we need to step this thread? If so, let the mach thread tell us so. |
| if (m_thread->IsStepping()) |
| { |
| // This is the primary thread, let the arch do anything it needs |
| if (NumSupportedHardwareBreakpoints() > 0) |
| { |
| if (EnableHardwareSingleStep(true) != KERN_SUCCESS) |
| { |
| DNBLogThreaded("DNBArchMachARM::ThreadWillResume() failed to enable hardware single step"); |
| } |
| } |
| } |
| |
| // Disable the triggered watchpoint temporarily before we resume. |
| // Plus, we try to enable hardware single step to execute past the instruction which triggered our watchpoint. |
| if (m_watchpoint_did_occur) |
| { |
| if (m_watchpoint_hw_index >= 0) |
| { |
| kern_return_t kret = GetDBGState(false); |
| if (kret == KERN_SUCCESS && !IsWatchpointEnabled(m_state.dbg, m_watchpoint_hw_index)) { |
| // The watchpoint might have been disabled by the user. We don't need to do anything at all |
| // to enable hardware single stepping. |
| m_watchpoint_did_occur = false; |
| m_watchpoint_hw_index = -1; |
| return; |
| } |
| |
| DisableHardwareWatchpoint0(m_watchpoint_hw_index, true); |
| DNBLogThreadedIf(LOG_WATCHPOINTS, "DNBArchMachARM::ThreadWillResume() DisableHardwareWatchpoint(%d) called", |
| m_watchpoint_hw_index); |
| |
| // Enable hardware single step to move past the watchpoint-triggering instruction. |
| m_watchpoint_resume_single_step_enabled = (EnableHardwareSingleStep(true) == KERN_SUCCESS); |
| |
| // If we are not able to enable single step to move past the watchpoint-triggering instruction, |
| // at least we should reset the two watchpoint member variables so that the next time around |
| // this callback function is invoked, the enclosing logical branch is skipped. |
| if (!m_watchpoint_resume_single_step_enabled) { |
| // Reset the two watchpoint member variables. |
| m_watchpoint_did_occur = false; |
| m_watchpoint_hw_index = -1; |
| DNBLogThreadedIf(LOG_WATCHPOINTS, "DNBArchMachARM::ThreadWillResume() failed to enable single step"); |
| } |
| else |
| DNBLogThreadedIf(LOG_WATCHPOINTS, "DNBArchMachARM::ThreadWillResume() succeeded to enable single step"); |
| } |
| } |
| } |
| |
| bool |
| DNBArchMachARM::ThreadDidStop() |
| { |
| bool success = true; |
| |
| m_state.InvalidateRegisterSetState (e_regSetALL); |
| |
| if (m_watchpoint_resume_single_step_enabled) |
| { |
| // Great! We now disable the hardware single step as well as re-enable the hardware watchpoint. |
| // See also ThreadWillResume(). |
| if (EnableHardwareSingleStep(false) == KERN_SUCCESS) |
| { |
| if (m_watchpoint_did_occur && m_watchpoint_hw_index >= 0) |
| { |
| EnableHardwareWatchpoint0(m_watchpoint_hw_index, true); |
| m_watchpoint_resume_single_step_enabled = false; |
| m_watchpoint_did_occur = false; |
| m_watchpoint_hw_index = -1; |
| } |
| else |
| { |
| DNBLogError("internal error detected: m_watchpoint_resume_step_enabled is true but (m_watchpoint_did_occur && m_watchpoint_hw_index >= 0) does not hold!"); |
| } |
| } |
| else |
| { |
| DNBLogError("internal error detected: m_watchpoint_resume_step_enabled is true but unable to disable single step!"); |
| } |
| } |
| |
| // Are we stepping a single instruction? |
| if (GetGPRState(true) == KERN_SUCCESS) |
| { |
| // We are single stepping, was this the primary thread? |
| if (m_thread->IsStepping()) |
| { |
| success = EnableHardwareSingleStep(false) == KERN_SUCCESS; |
| } |
| else |
| { |
| // The MachThread will automatically restore the suspend count |
| // in ThreadDidStop(), so we don't need to do anything here if |
| // we weren't the primary thread the last time |
| } |
| } |
| return success; |
| } |
| |
| bool |
| DNBArchMachARM::NotifyException(MachException::Data& exc) |
| { |
| switch (exc.exc_type) |
| { |
| default: |
| break; |
| case EXC_BREAKPOINT: |
| if (exc.exc_data.size() == 2 && exc.exc_data[0] == EXC_ARM_DA_DEBUG) |
| { |
| // exc_code = EXC_ARM_DA_DEBUG |
| // |
| // Check whether this corresponds to a watchpoint hit event. |
| // If yes, retrieve the exc_sub_code as the data break address. |
| if (!HasWatchpointOccurred()) |
| break; |
| |
| // The data break address is passed as exc_data[1]. |
| nub_addr_t addr = exc.exc_data[1]; |
| // Find the hardware index with the side effect of possibly massaging the |
| // addr to return the starting address as seen from the debugger side. |
| uint32_t hw_index = GetHardwareWatchpointHit(addr); |
| if (hw_index != INVALID_NUB_HW_INDEX) |
| { |
| m_watchpoint_did_occur = true; |
| m_watchpoint_hw_index = hw_index; |
| exc.exc_data[1] = addr; |
| // Piggyback the hw_index in the exc.data. |
| exc.exc_data.push_back(hw_index); |
| } |
| |
| return true; |
| } |
| break; |
| } |
| return false; |
| } |
| |
| bool |
| DNBArchMachARM::StepNotComplete () |
| { |
| if (m_hw_single_chained_step_addr != INVALID_NUB_ADDRESS) |
| { |
| kern_return_t kret = KERN_INVALID_ARGUMENT; |
| kret = GetGPRState(false); |
| if (kret == KERN_SUCCESS) |
| { |
| if (m_state.context.gpr.__pc == m_hw_single_chained_step_addr) |
| { |
| DNBLogThreadedIf(LOG_STEP, "Need to step some more at 0x%8.8x", m_hw_single_chained_step_addr); |
| return true; |
| } |
| } |
| } |
| |
| m_hw_single_chained_step_addr = INVALID_NUB_ADDRESS; |
| return false; |
| } |
| |
| |
| // Set the single step bit in the processor status register. |
| kern_return_t |
| DNBArchMachARM::EnableHardwareSingleStep (bool enable) |
| { |
| DNBError err; |
| DNBLogThreadedIf(LOG_STEP, "%s( enable = %d )", __FUNCTION__, enable); |
| |
| err = GetGPRState(false); |
| |
| if (err.Fail()) |
| { |
| err.LogThreaded("%s: failed to read the GPR registers", __FUNCTION__); |
| return err.Error(); |
| } |
| |
| err = GetDBGState(false); |
| |
| if (err.Fail()) |
| { |
| err.LogThreaded("%s: failed to read the DBG registers", __FUNCTION__); |
| return err.Error(); |
| } |
| |
| const uint32_t i = 0; |
| if (enable) |
| { |
| m_hw_single_chained_step_addr = INVALID_NUB_ADDRESS; |
| |
| // Save our previous state |
| m_dbg_save = m_state.dbg; |
| // Set a breakpoint that will stop when the PC doesn't match the current one! |
| m_state.dbg.__bvr[i] = m_state.context.gpr.__pc & 0xFFFFFFFCu; // Set the current PC as the breakpoint address |
| m_state.dbg.__bcr[i] = BCR_M_IMVA_MISMATCH | // Stop on address mismatch |
| S_USER | // Stop only in user mode |
| BCR_ENABLE; // Enable this breakpoint |
| if (m_state.context.gpr.__cpsr & 0x20) |
| { |
| // Thumb breakpoint |
| if (m_state.context.gpr.__pc & 2) |
| m_state.dbg.__bcr[i] |= BAS_IMVA_2_3; |
| else |
| m_state.dbg.__bcr[i] |= BAS_IMVA_0_1; |
| |
| uint16_t opcode; |
| if (sizeof(opcode) == m_thread->Process()->Task().ReadMemory(m_state.context.gpr.__pc, sizeof(opcode), &opcode)) |
| { |
| if (((opcode & 0xE000) == 0xE000) && opcode & 0x1800) |
| { |
| // 32 bit thumb opcode... |
| if (m_state.context.gpr.__pc & 2) |
| { |
| // We can't take care of a 32 bit thumb instruction single step |
| // with just IVA mismatching. We will need to chain an extra |
| // hardware single step in order to complete this single step... |
| m_hw_single_chained_step_addr = m_state.context.gpr.__pc + 2; |
| } |
| else |
| { |
| // Extend the number of bits to ignore for the mismatch |
| m_state.dbg.__bcr[i] |= BAS_IMVA_ALL; |
| } |
| } |
| } |
| } |
| else |
| { |
| // ARM breakpoint |
| m_state.dbg.__bcr[i] |= BAS_IMVA_ALL; // Stop when any address bits change |
| } |
| |
| DNBLogThreadedIf(LOG_STEP, "%s: BVR%u=0x%8.8x BCR%u=0x%8.8x", __FUNCTION__, i, m_state.dbg.__bvr[i], i, m_state.dbg.__bcr[i]); |
| |
| for (uint32_t j=i+1; j<16; ++j) |
| { |
| // Disable all others |
| m_state.dbg.__bvr[j] = 0; |
| m_state.dbg.__bcr[j] = 0; |
| } |
| } |
| else |
| { |
| // Just restore the state we had before we did single stepping |
| m_state.dbg = m_dbg_save; |
| } |
| |
| return SetDBGState(false); |
| } |
| |
| // return 1 if bit "BIT" is set in "value" |
| static inline uint32_t bit(uint32_t value, uint32_t bit) |
| { |
| return (value >> bit) & 1u; |
| } |
| |
| // return the bitfield "value[msbit:lsbit]". |
| static inline uint32_t bits(uint32_t value, uint32_t msbit, uint32_t lsbit) |
| { |
| assert(msbit >= lsbit); |
| uint32_t shift_left = sizeof(value) * 8 - 1 - msbit; |
| value <<= shift_left; // shift anything above the msbit off of the unsigned edge |
| value >>= (shift_left + lsbit); // shift it back again down to the lsbit (including undoing any shift from above) |
| return value; // return our result |
| } |
| |
| bool |
| DNBArchMachARM::ConditionPassed(uint8_t condition, uint32_t cpsr) |
| { |
| uint32_t cpsr_n = bit(cpsr, 31); // Negative condition code flag |
| uint32_t cpsr_z = bit(cpsr, 30); // Zero condition code flag |
| uint32_t cpsr_c = bit(cpsr, 29); // Carry condition code flag |
| uint32_t cpsr_v = bit(cpsr, 28); // Overflow condition code flag |
| |
| switch (condition) { |
| case COND_EQ: // (0x0) |
| if (cpsr_z == 1) return true; |
| break; |
| case COND_NE: // (0x1) |
| if (cpsr_z == 0) return true; |
| break; |
| case COND_CS: // (0x2) |
| if (cpsr_c == 1) return true; |
| break; |
| case COND_CC: // (0x3) |
| if (cpsr_c == 0) return true; |
| break; |
| case COND_MI: // (0x4) |
| if (cpsr_n == 1) return true; |
| break; |
| case COND_PL: // (0x5) |
| if (cpsr_n == 0) return true; |
| break; |
| case COND_VS: // (0x6) |
| if (cpsr_v == 1) return true; |
| break; |
| case COND_VC: // (0x7) |
| if (cpsr_v == 0) return true; |
| break; |
| case COND_HI: // (0x8) |
| if ((cpsr_c == 1) && (cpsr_z == 0)) return true; |
| break; |
| case COND_LS: // (0x9) |
| if ((cpsr_c == 0) || (cpsr_z == 1)) return true; |
| break; |
| case COND_GE: // (0xA) |
| if (cpsr_n == cpsr_v) return true; |
| break; |
| case COND_LT: // (0xB) |
| if (cpsr_n != cpsr_v) return true; |
| break; |
| case COND_GT: // (0xC) |
| if ((cpsr_z == 0) && (cpsr_n == cpsr_v)) return true; |
| break; |
| case COND_LE: // (0xD) |
| if ((cpsr_z == 1) || (cpsr_n != cpsr_v)) return true; |
| break; |
| default: |
| return true; |
| break; |
| } |
| |
| return false; |
| } |
| |
| uint32_t |
| DNBArchMachARM::NumSupportedHardwareBreakpoints() |
| { |
| // Set the init value to something that will let us know that we need to |
| // autodetect how many breakpoints are supported dynamically... |
| static uint32_t g_num_supported_hw_breakpoints = UINT_MAX; |
| if (g_num_supported_hw_breakpoints == UINT_MAX) |
| { |
| // Set this to zero in case we can't tell if there are any HW breakpoints |
| g_num_supported_hw_breakpoints = 0; |
| |
| size_t len; |
| uint32_t n = 0; |
| len = sizeof (n); |
| if (::sysctlbyname("hw.optional.breakpoint", &n, &len, NULL, 0) == 0) |
| { |
| g_num_supported_hw_breakpoints = n; |
| DNBLogThreadedIf(LOG_THREAD, "hw.optional.breakpoint=%u", n); |
| } |
| else |
| { |
| // Read the DBGDIDR to get the number of available hardware breakpoints |
| // However, in some of our current armv7 processors, hardware |
| // breakpoints/watchpoints were not properly connected. So detect those |
| // cases using a field in a sysctl. For now we are using "hw.cpusubtype" |
| // field to distinguish CPU architectures. This is a hack until we can |
| // get <rdar://problem/6372672> fixed, at which point we will switch to |
| // using a different sysctl string that will tell us how many BRPs |
| // are available to us directly without having to read DBGDIDR. |
| uint32_t register_DBGDIDR; |
| |
| asm("mrc p14, 0, %0, c0, c0, 0" : "=r" (register_DBGDIDR)); |
| uint32_t numBRPs = bits(register_DBGDIDR, 27, 24); |
| // Zero is reserved for the BRP count, so don't increment it if it is zero |
| if (numBRPs > 0) |
| numBRPs++; |
| DNBLogThreadedIf(LOG_THREAD, "DBGDIDR=0x%8.8x (number BRP pairs = %u)", register_DBGDIDR, numBRPs); |
| |
| if (numBRPs > 0) |
| { |
| uint32_t cpusubtype; |
| len = sizeof(cpusubtype); |
| // TODO: remove this hack and change to using hw.optional.xx when implmented |
| if (::sysctlbyname("hw.cpusubtype", &cpusubtype, &len, NULL, 0) == 0) |
| { |
| DNBLogThreadedIf(LOG_THREAD, "hw.cpusubtype=%d", cpusubtype); |
| if (cpusubtype == CPU_SUBTYPE_ARM_V7) |
| DNBLogThreadedIf(LOG_THREAD, "Hardware breakpoints disabled for armv7 (rdar://problem/6372672)"); |
| else |
| g_num_supported_hw_breakpoints = numBRPs; |
| } |
| } |
| } |
| } |
| return g_num_supported_hw_breakpoints; |
| } |
| |
| |
| uint32_t |
| DNBArchMachARM::NumSupportedHardwareWatchpoints() |
| { |
| // Set the init value to something that will let us know that we need to |
| // autodetect how many watchpoints are supported dynamically... |
| static uint32_t g_num_supported_hw_watchpoints = UINT_MAX; |
| if (g_num_supported_hw_watchpoints == UINT_MAX) |
| { |
| // Set this to zero in case we can't tell if there are any HW breakpoints |
| g_num_supported_hw_watchpoints = 0; |
| |
| |
| size_t len; |
| uint32_t n = 0; |
| len = sizeof (n); |
| if (::sysctlbyname("hw.optional.watchpoint", &n, &len, NULL, 0) == 0) |
| { |
| g_num_supported_hw_watchpoints = n; |
| DNBLogThreadedIf(LOG_THREAD, "hw.optional.watchpoint=%u", n); |
| } |
| else |
| { |
| // Read the DBGDIDR to get the number of available hardware breakpoints |
| // However, in some of our current armv7 processors, hardware |
| // breakpoints/watchpoints were not properly connected. So detect those |
| // cases using a field in a sysctl. For now we are using "hw.cpusubtype" |
| // field to distinguish CPU architectures. This is a hack until we can |
| // get <rdar://problem/6372672> fixed, at which point we will switch to |
| // using a different sysctl string that will tell us how many WRPs |
| // are available to us directly without having to read DBGDIDR. |
| |
| uint32_t register_DBGDIDR; |
| asm("mrc p14, 0, %0, c0, c0, 0" : "=r" (register_DBGDIDR)); |
| uint32_t numWRPs = bits(register_DBGDIDR, 31, 28) + 1; |
| DNBLogThreadedIf(LOG_THREAD, "DBGDIDR=0x%8.8x (number WRP pairs = %u)", register_DBGDIDR, numWRPs); |
| |
| if (numWRPs > 0) |
| { |
| uint32_t cpusubtype; |
| size_t len; |
| len = sizeof(cpusubtype); |
| // TODO: remove this hack and change to using hw.optional.xx when implmented |
| if (::sysctlbyname("hw.cpusubtype", &cpusubtype, &len, NULL, 0) == 0) |
| { |
| DNBLogThreadedIf(LOG_THREAD, "hw.cpusubtype=0x%d", cpusubtype); |
| |
| if (cpusubtype == CPU_SUBTYPE_ARM_V7) |
| DNBLogThreadedIf(LOG_THREAD, "Hardware watchpoints disabled for armv7 (rdar://problem/6372672)"); |
| else |
| g_num_supported_hw_watchpoints = numWRPs; |
| } |
| } |
| } |
| } |
| return g_num_supported_hw_watchpoints; |
| } |
| |
| |
| uint32_t |
| DNBArchMachARM::EnableHardwareBreakpoint (nub_addr_t addr, nub_size_t size) |
| { |
| // Make sure our address isn't bogus |
| if (addr & 1) |
| return INVALID_NUB_HW_INDEX; |
| |
| kern_return_t kret = GetDBGState(false); |
| |
| if (kret == KERN_SUCCESS) |
| { |
| const uint32_t num_hw_breakpoints = NumSupportedHardwareBreakpoints(); |
| uint32_t i; |
| for (i=0; i<num_hw_breakpoints; ++i) |
| { |
| if ((m_state.dbg.__bcr[i] & BCR_ENABLE) == 0) |
| break; // We found an available hw breakpoint slot (in i) |
| } |
| |
| // See if we found an available hw breakpoint slot above |
| if (i < num_hw_breakpoints) |
| { |
| // Make sure bits 1:0 are clear in our address |
| m_state.dbg.__bvr[i] = addr & ~((nub_addr_t)3); |
| |
| if (size == 2 || addr & 2) |
| { |
| uint32_t byte_addr_select = (addr & 2) ? BAS_IMVA_2_3 : BAS_IMVA_0_1; |
| |
| // We have a thumb breakpoint |
| // We have an ARM breakpoint |
| m_state.dbg.__bcr[i] = BCR_M_IMVA_MATCH | // Stop on address mismatch |
| byte_addr_select | // Set the correct byte address select so we only trigger on the correct opcode |
| S_USER | // Which modes should this breakpoint stop in? |
| BCR_ENABLE; // Enable this hardware breakpoint |
| DNBLogThreadedIf (LOG_BREAKPOINTS, "DNBArchMachARM::EnableHardwareBreakpoint( addr = 0x%8.8llx, size = %llu ) - BVR%u/BCR%u = 0x%8.8x / 0x%8.8x (Thumb)", |
| (uint64_t)addr, |
| (uint64_t)size, |
| i, |
| i, |
| m_state.dbg.__bvr[i], |
| m_state.dbg.__bcr[i]); |
| } |
| else if (size == 4) |
| { |
| // We have an ARM breakpoint |
| m_state.dbg.__bcr[i] = BCR_M_IMVA_MATCH | // Stop on address mismatch |
| BAS_IMVA_ALL | // Stop on any of the four bytes following the IMVA |
| S_USER | // Which modes should this breakpoint stop in? |
| BCR_ENABLE; // Enable this hardware breakpoint |
| DNBLogThreadedIf (LOG_BREAKPOINTS, "DNBArchMachARM::EnableHardwareBreakpoint( addr = 0x%8.8llx, size = %llu ) - BVR%u/BCR%u = 0x%8.8x / 0x%8.8x (ARM)", |
| (uint64_t)addr, |
| (uint64_t)size, |
| i, |
| i, |
| m_state.dbg.__bvr[i], |
| m_state.dbg.__bcr[i]); |
| } |
| |
| kret = SetDBGState(false); |
| DNBLogThreadedIf(LOG_BREAKPOINTS, "DNBArchMachARM::EnableHardwareBreakpoint() SetDBGState() => 0x%8.8x.", kret); |
| |
| if (kret == KERN_SUCCESS) |
| return i; |
| } |
| else |
| { |
| DNBLogThreadedIf (LOG_BREAKPOINTS, "DNBArchMachARM::EnableHardwareBreakpoint(addr = 0x%8.8llx, size = %llu) => all hardware breakpoint resources are being used.", (uint64_t)addr, (uint64_t)size); |
| } |
| } |
| |
| return INVALID_NUB_HW_INDEX; |
| } |
| |
| bool |
| DNBArchMachARM::DisableHardwareBreakpoint (uint32_t hw_index) |
| { |
| kern_return_t kret = GetDBGState(false); |
| |
| const uint32_t num_hw_points = NumSupportedHardwareBreakpoints(); |
| if (kret == KERN_SUCCESS) |
| { |
| if (hw_index < num_hw_points) |
| { |
| m_state.dbg.__bcr[hw_index] = 0; |
| DNBLogThreadedIf(LOG_BREAKPOINTS, "DNBArchMachARM::SetHardwareBreakpoint( %u ) - BVR%u = 0x%8.8x BCR%u = 0x%8.8x", |
| hw_index, |
| hw_index, |
| m_state.dbg.__bvr[hw_index], |
| hw_index, |
| m_state.dbg.__bcr[hw_index]); |
| |
| kret = SetDBGState(false); |
| |
| if (kret == KERN_SUCCESS) |
| return true; |
| } |
| } |
| return false; |
| } |
| |
| // This stores the lo->hi mappings. It's safe to initialize to all 0's |
| // since hi > lo and therefore LoHi[i] cannot be 0. |
| static uint32_t LoHi[16] = { 0 }; |
| |
| uint32_t |
| DNBArchMachARM::EnableHardwareWatchpoint (nub_addr_t addr, nub_size_t size, bool read, bool write, bool also_set_on_task) |
| { |
| DNBLogThreadedIf(LOG_WATCHPOINTS, "DNBArchMachARM::EnableHardwareWatchpoint(addr = 0x%8.8llx, size = %llu, read = %u, write = %u)", (uint64_t)addr, (uint64_t)size, read, write); |
| |
| const uint32_t num_hw_watchpoints = NumSupportedHardwareWatchpoints(); |
| |
| // Can't watch zero bytes |
| if (size == 0) |
| return INVALID_NUB_HW_INDEX; |
| |
| // We must watch for either read or write |
| if (read == false && write == false) |
| return INVALID_NUB_HW_INDEX; |
| |
| // Divide-and-conquer for size == 8. |
| if (size == 8) |
| { |
| uint32_t lo = EnableHardwareWatchpoint(addr, 4, read, write); |
| if (lo == INVALID_NUB_HW_INDEX) |
| return INVALID_NUB_HW_INDEX; |
| uint32_t hi = EnableHardwareWatchpoint(addr+4, 4, read, write); |
| if (hi == INVALID_NUB_HW_INDEX) |
| { |
| DisableHardwareWatchpoint(lo); |
| return INVALID_NUB_HW_INDEX; |
| } |
| // Tag this lo->hi mapping in our database. |
| LoHi[lo] = hi; |
| return lo; |
| } |
| |
| // Otherwise, can't watch more than 4 bytes per WVR/WCR pair |
| if (size > 4) |
| return INVALID_NUB_HW_INDEX; |
| |
| // We can only watch up to four bytes that follow a 4 byte aligned address |
| // per watchpoint register pair. Since we can only watch until the next 4 |
| // byte boundary, we need to make sure we can properly encode this. |
| |
| // addr_word_offset = addr % 4, i.e, is in set([0, 1, 2, 3]) |
| // |
| // +---+---+---+---+ |
| // | 0 | 1 | 2 | 3 | |
| // +---+---+---+---+ |
| // ^ |
| // | |
| // word address (4-byte aligned) = addr & 0xFFFFFFFC => goes into WVR |
| // |
| // examples: |
| // 1. addr_word_offset = 1, size = 1 to watch a uint_8 => byte_mask = (0b0001 << 1) = 0b0010 |
| // 2. addr_word_offset = 2, size = 2 to watch a uint_16 => byte_mask = (0b0011 << 2) = 0b1100 |
| // |
| // where byte_mask goes into WCR[8:5] |
| |
| uint32_t addr_word_offset = addr % 4; |
| DNBLogThreadedIf(LOG_WATCHPOINTS, "DNBArchMachARM::EnableHardwareWatchpoint() - addr_word_offset = 0x%8.8x", addr_word_offset); |
| |
| uint32_t byte_mask = ((1u << size) - 1u) << addr_word_offset; |
| DNBLogThreadedIf(LOG_WATCHPOINTS, "DNBArchMachARM::EnableHardwareWatchpoint() - byte_mask = 0x%8.8x", byte_mask); |
| if (byte_mask > 0xfu) |
| return INVALID_NUB_HW_INDEX; |
| |
| // Read the debug state |
| kern_return_t kret = GetDBGState(true); |
| |
| if (kret == KERN_SUCCESS) |
| { |
| // Check to make sure we have the needed hardware support |
| uint32_t i = 0; |
| |
| for (i=0; i<num_hw_watchpoints; ++i) |
| { |
| if ((m_state.dbg.__wcr[i] & WCR_ENABLE) == 0) |
| break; // We found an available hw watchpoint slot (in i) |
| } |
| |
| // See if we found an available hw watchpoint slot above |
| if (i < num_hw_watchpoints) |
| { |
| //DumpDBGState(m_state.dbg); |
| |
| // Make the byte_mask into a valid Byte Address Select mask |
| uint32_t byte_address_select = byte_mask << 5; |
| // Make sure bits 1:0 are clear in our address |
| m_state.dbg.__wvr[i] = addr & ~((nub_addr_t)3); // DVA (Data Virtual Address) |
| m_state.dbg.__wcr[i] = byte_address_select | // Which bytes that follow the DVA that we will watch |
| S_USER | // Stop only in user mode |
| (read ? WCR_LOAD : 0) | // Stop on read access? |
| (write ? WCR_STORE : 0) | // Stop on write access? |
| WCR_ENABLE; // Enable this watchpoint; |
| |
| DNBLogThreadedIf(LOG_WATCHPOINTS, "DNBArchMachARM::EnableHardwareWatchpoint() adding watchpoint on address 0x%llx with control register value 0x%x", (uint64_t) m_state.dbg.__wvr[i], (uint32_t) m_state.dbg.__wcr[i]); |
| |
| kret = SetDBGState(also_set_on_task); |
| //DumpDBGState(m_state.dbg); |
| |
| DNBLogThreadedIf(LOG_WATCHPOINTS, "DNBArchMachARM::EnableHardwareWatchpoint() SetDBGState() => 0x%8.8x.", kret); |
| |
| if (kret == KERN_SUCCESS) |
| return i; |
| } |
| else |
| { |
| DNBLogThreadedIf(LOG_WATCHPOINTS, "DNBArchMachARM::EnableHardwareWatchpoint(): All hardware resources (%u) are in use.", num_hw_watchpoints); |
| } |
| } |
| return INVALID_NUB_HW_INDEX; |
| } |
| |
| bool |
| DNBArchMachARM::EnableHardwareWatchpoint0 (uint32_t hw_index, bool Delegate) |
| { |
| kern_return_t kret = GetDBGState(false); |
| if (kret != KERN_SUCCESS) |
| return false; |
| |
| const uint32_t num_hw_points = NumSupportedHardwareWatchpoints(); |
| if (hw_index >= num_hw_points) |
| return false; |
| |
| if (Delegate && LoHi[hw_index]) { |
| // Enable lo and hi watchpoint hardware indexes. |
| return EnableHardwareWatchpoint0(hw_index, false) && |
| EnableHardwareWatchpoint0(LoHi[hw_index], false); |
| } |
| |
| m_state.dbg.__wcr[hw_index] |= (nub_addr_t)WCR_ENABLE; |
| DNBLogThreadedIf(LOG_WATCHPOINTS, "DNBArchMachARM::EnableHardwareWatchpoint( %u ) - WVR%u = 0x%8.8x WCR%u = 0x%8.8x", |
| hw_index, |
| hw_index, |
| m_state.dbg.__wvr[hw_index], |
| hw_index, |
| m_state.dbg.__wcr[hw_index]); |
| |
| kret = SetDBGState(false); |
| |
| return (kret == KERN_SUCCESS); |
| } |
| |
| bool |
| DNBArchMachARM::DisableHardwareWatchpoint (uint32_t hw_index) |
| { |
| return DisableHardwareWatchpoint0(hw_index, true); |
| } |
| bool |
| DNBArchMachARM::DisableHardwareWatchpoint0 (uint32_t hw_index, bool Delegate) |
| { |
| kern_return_t kret = GetDBGState(false); |
| if (kret != KERN_SUCCESS) |
| return false; |
| |
| const uint32_t num_hw_points = NumSupportedHardwareWatchpoints(); |
| if (hw_index >= num_hw_points) |
| return false; |
| |
| if (Delegate && LoHi[hw_index]) { |
| // Disable lo and hi watchpoint hardware indexes. |
| return DisableHardwareWatchpoint0(hw_index, false) && |
| DisableHardwareWatchpoint0(LoHi[hw_index], false); |
| } |
| |
| m_state.dbg.__wcr[hw_index] &= ~((nub_addr_t)WCR_ENABLE); |
| DNBLogThreadedIf(LOG_WATCHPOINTS, "DNBArchMachARM::DisableHardwareWatchpoint( %u ) - WVR%u = 0x%8.8x WCR%u = 0x%8.8x", |
| hw_index, |
| hw_index, |
| m_state.dbg.__wvr[hw_index], |
| hw_index, |
| m_state.dbg.__wcr[hw_index]); |
| |
| kret = SetDBGState(); |
| |
| return (kret == KERN_SUCCESS); |
| } |
| |
| // Returns -1 if the trailing bit patterns are not one of: |
| // { 0b???1, 0b??10, 0b?100, 0b1000 }. |
| static inline |
| int32_t |
| LowestBitSet(uint32_t val) |
| { |
| for (unsigned i = 0; i < 4; ++i) { |
| if (bit(val, i)) |
| return i; |
| } |
| return -1; |
| } |
| |
| // Iterate through the debug registers; return the index of the first watchpoint whose address matches. |
| // As a side effect, the starting address as understood by the debugger is returned which could be |
| // different from 'addr' passed as an in/out argument. |
| uint32_t |
| DNBArchMachARM::GetHardwareWatchpointHit(nub_addr_t &addr) |
| { |
| // Read the debug state |
| kern_return_t kret = GetDBGState(true); |
| //DumpDBGState(m_state.dbg); |
| DNBLogThreadedIf(LOG_WATCHPOINTS, "DNBArchMachARM::GetHardwareWatchpointHit() GetDBGState() => 0x%8.8x.", kret); |
| DNBLogThreadedIf(LOG_WATCHPOINTS, "DNBArchMachARM::GetHardwareWatchpointHit() addr = 0x%llx", (uint64_t)addr); |
| |
| // This is the watchpoint value to match against, i.e., word address. |
| nub_addr_t wp_val = addr & ~((nub_addr_t)3); |
| if (kret == KERN_SUCCESS) |
| { |
| DBG &debug_state = m_state.dbg; |
| uint32_t i, num = NumSupportedHardwareWatchpoints(); |
| for (i = 0; i < num; ++i) |
| { |
| nub_addr_t wp_addr = GetWatchAddress(debug_state, i); |
| DNBLogThreadedIf(LOG_WATCHPOINTS, |
| "DNBArchMachARM::GetHardwareWatchpointHit() slot: %u (addr = 0x%llx).", |
| i, (uint64_t)wp_addr); |
| if (wp_val == wp_addr) { |
| uint32_t byte_mask = bits(debug_state.__wcr[i], 8, 5); |
| |
| // Sanity check the byte_mask, first. |
| if (LowestBitSet(byte_mask) < 0) |
| continue; |
| |
| // Compute the starting address (from the point of view of the debugger). |
| addr = wp_addr + LowestBitSet(byte_mask); |
| return i; |
| } |
| } |
| } |
| return INVALID_NUB_HW_INDEX; |
| } |
| |
| // ThreadWillResume() calls this to clear bits[5:2] (Method of entry bits) of |
| // the Debug Status and Control Register (DSCR). |
| // |
| // b0010 = a watchpoint occurred |
| // b0000 is the reset value |
| void |
| DNBArchMachARM::ClearWatchpointOccurred() |
| { |
| uint32_t register_DBGDSCR; |
| asm("mrc p14, 0, %0, c0, c1, 0" : "=r" (register_DBGDSCR)); |
| if (bits(register_DBGDSCR, 5, 2) == WATCHPOINT_OCCURRED) |
| { |
| uint32_t mask = ~(0xF << 2); |
| register_DBGDSCR &= mask; |
| asm("mcr p14, 0, %0, c0, c1, 0" : "=r" (register_DBGDSCR)); |
| } |
| return; |
| } |
| |
| // NotifyException() calls this to double check that a watchpoint has occurred |
| // by inspecting the bits[5:2] field of the Debug Status and Control Register |
| // (DSCR). |
| // |
| // b0010 = a watchpoint occurred |
| bool |
| DNBArchMachARM::HasWatchpointOccurred() |
| { |
| uint32_t register_DBGDSCR; |
| asm("mrc p14, 0, %0, c0, c1, 0" : "=r" (register_DBGDSCR)); |
| return (bits(register_DBGDSCR, 5, 2) == WATCHPOINT_OCCURRED); |
| } |
| |
| bool |
| DNBArchMachARM::IsWatchpointEnabled(const DBG &debug_state, uint32_t hw_index) |
| { |
| // Watchpoint Control Registers, bitfield definitions |
| // ... |
| // Bits Value Description |
| // [0] 0 Watchpoint disabled |
| // 1 Watchpoint enabled. |
| return (debug_state.__wcr[hw_index] & 1u); |
| } |
| |
| nub_addr_t |
| DNBArchMachARM::GetWatchAddress(const DBG &debug_state, uint32_t hw_index) |
| { |
| // Watchpoint Value Registers, bitfield definitions |
| // Bits Description |
| // [31:2] Watchpoint value (word address, i.e., 4-byte aligned) |
| // [1:0] RAZ/SBZP |
| return bits(debug_state.__wvr[hw_index], 31, 0); |
| } |
| |
| //---------------------------------------------------------------------- |
| // Register information defintions for 32 bit ARMV7. |
| //---------------------------------------------------------------------- |
| enum gpr_regnums |
| { |
| gpr_r0 = 0, |
| gpr_r1, |
| gpr_r2, |
| gpr_r3, |
| gpr_r4, |
| gpr_r5, |
| gpr_r6, |
| gpr_r7, |
| gpr_r8, |
| gpr_r9, |
| gpr_r10, |
| gpr_r11, |
| gpr_r12, |
| gpr_sp, |
| gpr_lr, |
| gpr_pc, |
| gpr_cpsr |
| }; |
| |
| enum |
| { |
| vfp_s0 = 17, // match the g_gdb_register_map_arm table in RNBRemote.cpp |
| vfp_s1, |
| vfp_s2, |
| vfp_s3, |
| vfp_s4, |
| vfp_s5, |
| vfp_s6, |
| vfp_s7, |
| vfp_s8, |
| vfp_s9, |
| vfp_s10, |
| vfp_s11, |
| vfp_s12, |
| vfp_s13, |
| vfp_s14, |
| vfp_s15, |
| vfp_s16, |
| vfp_s17, |
| vfp_s18, |
| vfp_s19, |
| vfp_s20, |
| vfp_s21, |
| vfp_s22, |
| vfp_s23, |
| vfp_s24, |
| vfp_s25, |
| vfp_s26, |
| vfp_s27, |
| vfp_s28, |
| vfp_s29, |
| vfp_s30, |
| vfp_s31 |
| }; |
| |
| enum |
| { |
| vfp_d0 = 49, // match the g_gdb_register_map_arm table in RNBRemote.cpp |
| vfp_d1, |
| vfp_d2, |
| vfp_d3, |
| vfp_d4, |
| vfp_d5, |
| vfp_d6, |
| vfp_d7, |
| vfp_d8, |
| vfp_d9, |
| vfp_d10, |
| vfp_d11, |
| vfp_d12, |
| vfp_d13, |
| vfp_d14, |
| vfp_d15, |
| vfp_d16, |
| vfp_d17, |
| vfp_d18, |
| vfp_d19, |
| vfp_d20, |
| vfp_d21, |
| vfp_d22, |
| vfp_d23, |
| vfp_d24, |
| vfp_d25, |
| vfp_d26, |
| vfp_d27, |
| vfp_d28, |
| vfp_d29, |
| vfp_d30, |
| vfp_d31 |
| }; |
| |
| enum |
| { |
| vfp_q0 = 81, // match the g_gdb_register_map_arm table in RNBRemote.cpp |
| vfp_q1, |
| vfp_q2, |
| vfp_q3, |
| vfp_q4, |
| vfp_q5, |
| vfp_q6, |
| vfp_q7, |
| vfp_q8, |
| vfp_q9, |
| vfp_q10, |
| vfp_q11, |
| vfp_q12, |
| vfp_q13, |
| vfp_q14, |
| vfp_q15, |
| vfp_fpscr |
| }; |
| |
| enum |
| { |
| exc_exception, |
| exc_fsr, |
| exc_far, |
| }; |
| |
| #define GPR_OFFSET_IDX(idx) (offsetof (DNBArchMachARM::GPR, __r[idx])) |
| #define GPR_OFFSET_NAME(reg) (offsetof (DNBArchMachARM::GPR, __##reg)) |
| |
| #define EXC_OFFSET(reg) (offsetof (DNBArchMachARM::EXC, __##reg) + offsetof (DNBArchMachARM::Context, exc)) |
| |
| // These macros will auto define the register name, alt name, register size, |
| // register offset, encoding, format and native register. This ensures that |
| // the register state structures are defined correctly and have the correct |
| // sizes and offsets. |
| #define DEFINE_GPR_IDX(idx, reg, alt, gen) { e_regSetGPR, gpr_##reg, #reg, alt, Uint, Hex, 4, GPR_OFFSET_IDX(idx), gcc_##reg, dwarf_##reg, gen, INVALID_NUB_REGNUM, NULL, NULL} |
| #define DEFINE_GPR_NAME(reg, alt, gen, inval) { e_regSetGPR, gpr_##reg, #reg, alt, Uint, Hex, 4, GPR_OFFSET_NAME(reg), gcc_##reg, dwarf_##reg, gen, INVALID_NUB_REGNUM, NULL, inval} |
| |
| // In case we are debugging to a debug target that the ability to |
| // change into the protected modes with folded registers (ABT, IRQ, |
| // FIQ, SYS, USR, etc..), we should invalidate r8-r14 if the CPSR |
| // gets modified. |
| |
| uint32_t g_invalidate_cpsr[] = { |
| gpr_r8, |
| gpr_r9, |
| gpr_r10, |
| gpr_r11, |
| gpr_r12, |
| gpr_sp, |
| gpr_lr, |
| INVALID_NUB_REGNUM }; |
| |
| // General purpose registers |
| const DNBRegisterInfo |
| DNBArchMachARM::g_gpr_registers[] = |
| { |
| DEFINE_GPR_IDX ( 0, r0,"arg1", GENERIC_REGNUM_ARG1 ), |
| DEFINE_GPR_IDX ( 1, r1,"arg2", GENERIC_REGNUM_ARG2 ), |
| DEFINE_GPR_IDX ( 2, r2,"arg3", GENERIC_REGNUM_ARG3 ), |
| DEFINE_GPR_IDX ( 3, r3,"arg4", GENERIC_REGNUM_ARG4 ), |
| DEFINE_GPR_IDX ( 4, r4, NULL, INVALID_NUB_REGNUM ), |
| DEFINE_GPR_IDX ( 5, r5, NULL, INVALID_NUB_REGNUM ), |
| DEFINE_GPR_IDX ( 6, r6, NULL, INVALID_NUB_REGNUM ), |
| DEFINE_GPR_IDX ( 7, r7, "fp", GENERIC_REGNUM_FP ), |
| DEFINE_GPR_IDX ( 8, r8, NULL, INVALID_NUB_REGNUM ), |
| DEFINE_GPR_IDX ( 9, r9, NULL, INVALID_NUB_REGNUM ), |
| DEFINE_GPR_IDX (10, r10, NULL, INVALID_NUB_REGNUM ), |
| DEFINE_GPR_IDX (11, r11, NULL, INVALID_NUB_REGNUM ), |
| DEFINE_GPR_IDX (12, r12, NULL, INVALID_NUB_REGNUM ), |
| DEFINE_GPR_NAME (sp, "r13", GENERIC_REGNUM_SP, NULL), |
| DEFINE_GPR_NAME (lr, "r14", GENERIC_REGNUM_RA, NULL), |
| DEFINE_GPR_NAME (pc, "r15", GENERIC_REGNUM_PC, NULL), |
| DEFINE_GPR_NAME (cpsr, "flags", GENERIC_REGNUM_FLAGS, g_invalidate_cpsr) |
| }; |
| |
| uint32_t g_contained_q0[] {vfp_q0, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q1[] {vfp_q1, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q2[] {vfp_q2, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q3[] {vfp_q3, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q4[] {vfp_q4, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q5[] {vfp_q5, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q6[] {vfp_q6, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q7[] {vfp_q7, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q8[] {vfp_q8, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q9[] {vfp_q9, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q10[] {vfp_q10, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q11[] {vfp_q11, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q12[] {vfp_q12, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q13[] {vfp_q13, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q14[] {vfp_q14, INVALID_NUB_REGNUM }; |
| uint32_t g_contained_q15[] {vfp_q15, INVALID_NUB_REGNUM }; |
| |
| uint32_t g_invalidate_q0[] {vfp_q0, vfp_d0, vfp_d1, vfp_s0, vfp_s1, vfp_s2, vfp_s3, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q1[] {vfp_q1, vfp_d2, vfp_d3, vfp_s4, vfp_s5, vfp_s6, vfp_s7, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q2[] {vfp_q2, vfp_d4, vfp_d5, vfp_s8, vfp_s9, vfp_s10, vfp_s11, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q3[] {vfp_q3, vfp_d6, vfp_d7, vfp_s12, vfp_s13, vfp_s14, vfp_s15, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q4[] {vfp_q4, vfp_d8, vfp_d9, vfp_s16, vfp_s17, vfp_s18, vfp_s19, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q5[] {vfp_q5, vfp_d10, vfp_d11, vfp_s20, vfp_s21, vfp_s22, vfp_s23, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q6[] {vfp_q6, vfp_d12, vfp_d13, vfp_s24, vfp_s25, vfp_s26, vfp_s27, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q7[] {vfp_q7, vfp_d14, vfp_d15, vfp_s28, vfp_s29, vfp_s30, vfp_s31, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q8[] {vfp_q8, vfp_d16, vfp_d17, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q9[] {vfp_q9, vfp_d18, vfp_d19, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q10[] {vfp_q10, vfp_d20, vfp_d21, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q11[] {vfp_q11, vfp_d22, vfp_d23, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q12[] {vfp_q12, vfp_d24, vfp_d25, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q13[] {vfp_q13, vfp_d26, vfp_d27, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q14[] {vfp_q14, vfp_d28, vfp_d29, INVALID_NUB_REGNUM }; |
| uint32_t g_invalidate_q15[] {vfp_q15, vfp_d30, vfp_d31, INVALID_NUB_REGNUM }; |
| |
| #define VFP_S_OFFSET_IDX(idx) (offsetof (DNBArchMachARM::FPU, __r[(idx)]) + offsetof (DNBArchMachARM::Context, vfp)) |
| #define VFP_D_OFFSET_IDX(idx) (VFP_S_OFFSET_IDX ((idx) * 2)) |
| #define VFP_Q_OFFSET_IDX(idx) (VFP_S_OFFSET_IDX ((idx) * 4)) |
| |
| #define VFP_OFFSET_NAME(reg) (offsetof (DNBArchMachARM::FPU, __##reg) + offsetof (DNBArchMachARM::Context, vfp)) |
| |
| #define FLOAT_FORMAT Float |
| |
| #define DEFINE_VFP_S_IDX(idx) e_regSetVFP, vfp_s##idx - vfp_s0, "s" #idx, NULL, IEEE754, FLOAT_FORMAT, 4, VFP_S_OFFSET_IDX(idx), INVALID_NUB_REGNUM, dwarf_s##idx, INVALID_NUB_REGNUM, INVALID_NUB_REGNUM |
| #define DEFINE_VFP_D_IDX(idx) e_regSetVFP, vfp_d##idx - vfp_s0, "d" #idx, NULL, IEEE754, FLOAT_FORMAT, 8, VFP_D_OFFSET_IDX(idx), INVALID_NUB_REGNUM, dwarf_d##idx, INVALID_NUB_REGNUM, INVALID_NUB_REGNUM |
| #define DEFINE_VFP_Q_IDX(idx) e_regSetVFP, vfp_q##idx - vfp_s0, "q" #idx, NULL, Vector, VectorOfUInt8, 16, VFP_Q_OFFSET_IDX(idx), INVALID_NUB_REGNUM, dwarf_q##idx, INVALID_NUB_REGNUM, INVALID_NUB_REGNUM |
| |
| // Floating point registers |
| const DNBRegisterInfo |
| DNBArchMachARM::g_vfp_registers[] = |
| { |
| { DEFINE_VFP_S_IDX ( 0), g_contained_q0, g_invalidate_q0 }, |
| { DEFINE_VFP_S_IDX ( 1), g_contained_q0, g_invalidate_q0 }, |
| { DEFINE_VFP_S_IDX ( 2), g_contained_q0, g_invalidate_q0 }, |
| { DEFINE_VFP_S_IDX ( 3), g_contained_q0, g_invalidate_q0 }, |
| { DEFINE_VFP_S_IDX ( 4), g_contained_q1, g_invalidate_q1 }, |
| { DEFINE_VFP_S_IDX ( 5), g_contained_q1, g_invalidate_q1 }, |
| { DEFINE_VFP_S_IDX ( 6), g_contained_q1, g_invalidate_q1 }, |
| { DEFINE_VFP_S_IDX ( 7), g_contained_q1, g_invalidate_q1 }, |
| { DEFINE_VFP_S_IDX ( 8), g_contained_q2, g_invalidate_q2 }, |
| { DEFINE_VFP_S_IDX ( 9), g_contained_q2, g_invalidate_q2 }, |
| { DEFINE_VFP_S_IDX (10), g_contained_q2, g_invalidate_q2 }, |
| { DEFINE_VFP_S_IDX (11), g_contained_q2, g_invalidate_q2 }, |
| { DEFINE_VFP_S_IDX (12), g_contained_q3, g_invalidate_q3 }, |
| { DEFINE_VFP_S_IDX (13), g_contained_q3, g_invalidate_q3 }, |
| { DEFINE_VFP_S_IDX (14), g_contained_q3, g_invalidate_q3 }, |
| { DEFINE_VFP_S_IDX (15), g_contained_q3, g_invalidate_q3 }, |
| { DEFINE_VFP_S_IDX (16), g_contained_q4, g_invalidate_q4 }, |
| { DEFINE_VFP_S_IDX (17), g_contained_q4, g_invalidate_q4 }, |
| { DEFINE_VFP_S_IDX (18), g_contained_q4, g_invalidate_q4 }, |
| { DEFINE_VFP_S_IDX (19), g_contained_q4, g_invalidate_q4 }, |
| { DEFINE_VFP_S_IDX (20), g_contained_q5, g_invalidate_q5 }, |
| { DEFINE_VFP_S_IDX (21), g_contained_q5, g_invalidate_q5 }, |
| { DEFINE_VFP_S_IDX (22), g_contained_q5, g_invalidate_q5 }, |
| { DEFINE_VFP_S_IDX (23), g_contained_q5, g_invalidate_q5 }, |
| { DEFINE_VFP_S_IDX (24), g_contained_q6, g_invalidate_q6 }, |
| { DEFINE_VFP_S_IDX (25), g_contained_q6, g_invalidate_q6 }, |
| { DEFINE_VFP_S_IDX (26), g_contained_q6, g_invalidate_q6 }, |
| { DEFINE_VFP_S_IDX (27), g_contained_q6, g_invalidate_q6 }, |
| { DEFINE_VFP_S_IDX (28), g_contained_q7, g_invalidate_q7 }, |
| { DEFINE_VFP_S_IDX (29), g_contained_q7, g_invalidate_q7 }, |
| { DEFINE_VFP_S_IDX (30), g_contained_q7, g_invalidate_q7 }, |
| { DEFINE_VFP_S_IDX (31), g_contained_q7, g_invalidate_q7 }, |
| |
| { DEFINE_VFP_D_IDX (0), g_contained_q0, g_invalidate_q0 }, |
| { DEFINE_VFP_D_IDX (1), g_contained_q0, g_invalidate_q0 }, |
| { DEFINE_VFP_D_IDX (2), g_contained_q1, g_invalidate_q1 }, |
| { DEFINE_VFP_D_IDX (3), g_contained_q1, g_invalidate_q1 }, |
| { DEFINE_VFP_D_IDX (4), g_contained_q2, g_invalidate_q2 }, |
| { DEFINE_VFP_D_IDX (5), g_contained_q2, g_invalidate_q2 }, |
| { DEFINE_VFP_D_IDX (6), g_contained_q3, g_invalidate_q3 }, |
| { DEFINE_VFP_D_IDX (7), g_contained_q3, g_invalidate_q3 }, |
| { DEFINE_VFP_D_IDX (8), g_contained_q4, g_invalidate_q4 }, |
| { DEFINE_VFP_D_IDX (9), g_contained_q4, g_invalidate_q4 }, |
| { DEFINE_VFP_D_IDX (10), g_contained_q5, g_invalidate_q5 }, |
| { DEFINE_VFP_D_IDX (11), g_contained_q5, g_invalidate_q5 }, |
| { DEFINE_VFP_D_IDX (12), g_contained_q6, g_invalidate_q6 }, |
| { DEFINE_VFP_D_IDX (13), g_contained_q6, g_invalidate_q6 }, |
| { DEFINE_VFP_D_IDX (14), g_contained_q7, g_invalidate_q7 }, |
| { DEFINE_VFP_D_IDX (15), g_contained_q7, g_invalidate_q7 }, |
| { DEFINE_VFP_D_IDX (16), g_contained_q8, g_invalidate_q8 }, |
| { DEFINE_VFP_D_IDX (17), g_contained_q8, g_invalidate_q8 }, |
| { DEFINE_VFP_D_IDX (18), g_contained_q9, g_invalidate_q9 }, |
| { DEFINE_VFP_D_IDX (19), g_contained_q9, g_invalidate_q9 }, |
| { DEFINE_VFP_D_IDX (20), g_contained_q10, g_invalidate_q10 }, |
| { DEFINE_VFP_D_IDX (21), g_contained_q10, g_invalidate_q10 }, |
| { DEFINE_VFP_D_IDX (22), g_contained_q11, g_invalidate_q11 }, |
| { DEFINE_VFP_D_IDX (23), g_contained_q11, g_invalidate_q11 }, |
| { DEFINE_VFP_D_IDX (24), g_contained_q12, g_invalidate_q12 }, |
| { DEFINE_VFP_D_IDX (25), g_contained_q12, g_invalidate_q12 }, |
| { DEFINE_VFP_D_IDX (26), g_contained_q13, g_invalidate_q13 }, |
| { DEFINE_VFP_D_IDX (27), g_contained_q13, g_invalidate_q13 }, |
| { DEFINE_VFP_D_IDX (28), g_contained_q14, g_invalidate_q14 }, |
| { DEFINE_VFP_D_IDX (29), g_contained_q14, g_invalidate_q14 }, |
| { DEFINE_VFP_D_IDX (30), g_contained_q15, g_invalidate_q15 }, |
| { DEFINE_VFP_D_IDX (31), g_contained_q15, g_invalidate_q15 }, |
| |
| { DEFINE_VFP_Q_IDX (0), NULL, g_invalidate_q0 }, |
| { DEFINE_VFP_Q_IDX (1), NULL, g_invalidate_q1 }, |
| { DEFINE_VFP_Q_IDX (2), NULL, g_invalidate_q2 }, |
| { DEFINE_VFP_Q_IDX (3), NULL, g_invalidate_q3 }, |
| { DEFINE_VFP_Q_IDX (4), NULL, g_invalidate_q4 }, |
| { DEFINE_VFP_Q_IDX (5), NULL, g_invalidate_q5 }, |
| { DEFINE_VFP_Q_IDX (6), NULL, g_invalidate_q6 }, |
| { DEFINE_VFP_Q_IDX (7), NULL, g_invalidate_q7 }, |
| { DEFINE_VFP_Q_IDX (8), NULL, g_invalidate_q8 }, |
| { DEFINE_VFP_Q_IDX (9), NULL, g_invalidate_q9 }, |
| { DEFINE_VFP_Q_IDX (10), NULL, g_invalidate_q10 }, |
| { DEFINE_VFP_Q_IDX (11), NULL, g_invalidate_q11 }, |
| { DEFINE_VFP_Q_IDX (12), NULL, g_invalidate_q12 }, |
| { DEFINE_VFP_Q_IDX (13), NULL, g_invalidate_q13 }, |
| { DEFINE_VFP_Q_IDX (14), NULL, g_invalidate_q14 }, |
| { DEFINE_VFP_Q_IDX (15), NULL, g_invalidate_q15 }, |
| |
| { e_regSetVFP, vfp_fpscr, "fpscr", NULL, Uint, Hex, 4, VFP_OFFSET_NAME(fpscr), INVALID_NUB_REGNUM, INVALID_NUB_REGNUM, INVALID_NUB_REGNUM, INVALID_NUB_REGNUM, NULL, NULL } |
| }; |
| |
| // Exception registers |
| |
| const DNBRegisterInfo |
| DNBArchMachARM::g_exc_registers[] = |
| { |
| { e_regSetVFP, exc_exception , "exception" , NULL, Uint, Hex, 4, EXC_OFFSET(exception) , INVALID_NUB_REGNUM, INVALID_NUB_REGNUM, INVALID_NUB_REGNUM, INVALID_NUB_REGNUM }, |
| { e_regSetVFP, exc_fsr , "fsr" , NULL, Uint, Hex, 4, EXC_OFFSET(fsr) , INVALID_NUB_REGNUM, INVALID_NUB_REGNUM, INVALID_NUB_REGNUM, INVALID_NUB_REGNUM }, |
| { e_regSetVFP, exc_far , "far" , NULL, Uint, Hex, 4, EXC_OFFSET(far) , INVALID_NUB_REGNUM, INVALID_NUB_REGNUM, INVALID_NUB_REGNUM, INVALID_NUB_REGNUM } |
| }; |
| |
| // Number of registers in each register set |
| const size_t DNBArchMachARM::k_num_gpr_registers = sizeof(g_gpr_registers)/sizeof(DNBRegisterInfo); |
| const size_t DNBArchMachARM::k_num_vfp_registers = sizeof(g_vfp_registers)/sizeof(DNBRegisterInfo); |
| const size_t DNBArchMachARM::k_num_exc_registers = sizeof(g_exc_registers)/sizeof(DNBRegisterInfo); |
| const size_t DNBArchMachARM::k_num_all_registers = k_num_gpr_registers + k_num_vfp_registers + k_num_exc_registers; |
| |
| //---------------------------------------------------------------------- |
| // Register set definitions. The first definitions at register set index |
| // of zero is for all registers, followed by other registers sets. The |
| // register information for the all register set need not be filled in. |
| //---------------------------------------------------------------------- |
| const DNBRegisterSetInfo |
| DNBArchMachARM::g_reg_sets[] = |
| { |
| { "ARM Registers", NULL, k_num_all_registers }, |
| { "General Purpose Registers", g_gpr_registers, k_num_gpr_registers }, |
| { "Floating Point Registers", g_vfp_registers, k_num_vfp_registers }, |
| { "Exception State Registers", g_exc_registers, k_num_exc_registers } |
| }; |
| // Total number of register sets for this architecture |
| const size_t DNBArchMachARM::k_num_register_sets = sizeof(g_reg_sets)/sizeof(DNBRegisterSetInfo); |
| |
| |
| const DNBRegisterSetInfo * |
| DNBArchMachARM::GetRegisterSetInfo(nub_size_t *num_reg_sets) |
| { |
| *num_reg_sets = k_num_register_sets; |
| return g_reg_sets; |
| } |
| |
| bool |
| DNBArchMachARM::GetRegisterValue(int set, int reg, DNBRegisterValue *value) |
| { |
| if (set == REGISTER_SET_GENERIC) |
| { |
| switch (reg) |
| { |
| case GENERIC_REGNUM_PC: // Program Counter |
| set = e_regSetGPR; |
| reg = gpr_pc; |
| break; |
| |
| case GENERIC_REGNUM_SP: // Stack Pointer |
| set = e_regSetGPR; |
| reg = gpr_sp; |
| break; |
| |
| case GENERIC_REGNUM_FP: // Frame Pointer |
| set = e_regSetGPR; |
| reg = gpr_r7; // is this the right reg? |
| break; |
| |
| case GENERIC_REGNUM_RA: // Return Address |
| set = e_regSetGPR; |
| reg = gpr_lr; |
| break; |
| |
| case GENERIC_REGNUM_FLAGS: // Processor flags register |
| set = e_regSetGPR; |
| reg = gpr_cpsr; |
| break; |
| |
| default: |
| return false; |
| } |
| } |
| |
| if (GetRegisterState(set, false) != KERN_SUCCESS) |
| return false; |
| |
| const DNBRegisterInfo *regInfo = m_thread->GetRegisterInfo(set, reg); |
| if (regInfo) |
| { |
| value->info = *regInfo; |
| switch (set) |
| { |
| case e_regSetGPR: |
| if (reg < k_num_gpr_registers) |
| { |
| value->value.uint32 = m_state.context.gpr.__r[reg]; |
| return true; |
| } |
| break; |
| |
| case e_regSetVFP: |
| // "reg" is an index into the floating point register set at this point. |
| // We need to translate it up so entry 0 in the fp reg set is the same as vfp_s0 |
| // in the enumerated values for case statement below. |
| reg += vfp_s0; |
| if (reg >= vfp_s0 && reg <= vfp_s31) |
| { |
| value->value.uint32 = m_state.context.vfp.__r[reg - vfp_s0]; |
| return true; |
| } |
| else if (reg >= vfp_d0 && reg <= vfp_d31) |
| { |
| uint32_t d_reg_idx = reg - vfp_d0; |
| uint32_t s_reg_idx = d_reg_idx * 2; |
| value->value.v_sint32[0] = m_state.context.vfp.__r[s_reg_idx + 0]; |
| value->value.v_sint32[1] = m_state.context.vfp.__r[s_reg_idx + 1]; |
| return true; |
| } |
| else if (reg >= vfp_q0 && reg <= vfp_q15) |
| { |
| uint32_t s_reg_idx = (reg - vfp_q0) * 4; |
| memcpy (&value->value.v_uint8, (uint8_t *) &m_state.context.vfp.__r[s_reg_idx], 16); |
| return true; |
| } |
| |
| else if (reg == vfp_fpscr) |
| { |
| value->value.uint32 = m_state.context.vfp.__fpscr; |
| return true; |
| } |
| break; |
| |
| case e_regSetEXC: |
| if (reg < k_num_exc_registers) |
| { |
| value->value.uint32 = (&m_state.context.exc.__exception)[reg]; |
| return true; |
| } |
| break; |
| } |
| } |
| return false; |
| } |
| |
| bool |
| DNBArchMachARM::SetRegisterValue(int set, int reg, const DNBRegisterValue *value) |
| { |
| if (set == REGISTER_SET_GENERIC) |
| { |
| switch (reg) |
| { |
| case GENERIC_REGNUM_PC: // Program Counter |
| set = e_regSetGPR; |
| reg = gpr_pc; |
| break; |
| |
| case GENERIC_REGNUM_SP: // Stack Pointer |
| set = e_regSetGPR; |
| reg = gpr_sp; |
| break; |
| |
| case GENERIC_REGNUM_FP: // Frame Pointer |
| set = e_regSetGPR; |
| reg = gpr_r7; |
| break; |
| |
| case GENERIC_REGNUM_RA: // Return Address |
| set = e_regSetGPR; |
| reg = gpr_lr; |
| break; |
| |
| case GENERIC_REGNUM_FLAGS: // Processor flags register |
| set = e_regSetGPR; |
| reg = gpr_cpsr; |
| break; |
| |
| default: |
| return false; |
| } |
| } |
| |
| if (GetRegisterState(set, false) != KERN_SUCCESS) |
| return false; |
| |
| bool success = false; |
| const DNBRegisterInfo *regInfo = m_thread->GetRegisterInfo(set, reg); |
| if (regInfo) |
| { |
| switch (set) |
| { |
| case e_regSetGPR: |
| if (reg < k_num_gpr_registers) |
| { |
| m_state.context.gpr.__r[reg] = value->value.uint32; |
| success = true; |
| } |
| break; |
| |
| case e_regSetVFP: |
| // "reg" is an index into the floating point register set at this point. |
| // We need to translate it up so entry 0 in the fp reg set is the same as vfp_s0 |
| // in the enumerated values for case statement below. |
| reg += vfp_s0; |
| |
| if (reg >= vfp_s0 && reg <= vfp_s31) |
| { |
| m_state.context.vfp.__r[reg - vfp_s0] = value->value.uint32; |
| success = true; |
| } |
| else if (reg >= vfp_d0 && reg <= vfp_d31) |
| { |
| uint32_t d_reg_idx = reg - vfp_d0; |
| uint32_t s_reg_idx = d_reg_idx * 2; |
| m_state.context.vfp.__r[s_reg_idx + 0] = value->value.v_sint32[0]; |
| m_state.context.vfp.__r[s_reg_idx + 1] = value->value.v_sint32[1]; |
| success = true; |
| } |
| else if (reg >= vfp_q0 && reg <= vfp_q15) |
| { |
| uint32_t s_reg_idx = (reg - vfp_q0) * 4; |
| memcpy ((uint8_t *) &m_state.context.vfp.__r[s_reg_idx], &value->value.v_uint8, 16); |
| return true; |
| } |
| else if (reg == vfp_fpscr) |
| { |
| m_state.context.vfp.__fpscr = value->value.uint32; |
| success = true; |
| } |
| break; |
| |
| case e_regSetEXC: |
| if (reg < k_num_exc_registers) |
| { |
| (&m_state.context.exc.__exception)[reg] = value->value.uint32; |
| success = true; |
| } |
| break; |
| } |
| |
| } |
| if (success) |
| return SetRegisterState(set) == KERN_SUCCESS; |
| return false; |
| } |
| |
| kern_return_t |
| DNBArchMachARM::GetRegisterState(int set, bool force) |
| { |
| switch (set) |
| { |
| case e_regSetALL: return GetGPRState(force) | |
| GetVFPState(force) | |
| GetEXCState(force) | |
| GetDBGState(force); |
| case e_regSetGPR: return GetGPRState(force); |
| case e_regSetVFP: return GetVFPState(force); |
| case e_regSetEXC: return GetEXCState(force); |
| case e_regSetDBG: return GetDBGState(force); |
| default: break; |
| } |
| return KERN_INVALID_ARGUMENT; |
| } |
| |
| kern_return_t |
| DNBArchMachARM::SetRegisterState(int set) |
| { |
| // Make sure we have a valid context to set. |
| kern_return_t err = GetRegisterState(set, false); |
| if (err != KERN_SUCCESS) |
| return err; |
| |
| switch (set) |
| { |
| case e_regSetALL: return SetGPRState() | |
| SetVFPState() | |
| SetEXCState() | |
| SetDBGState(false); |
| case e_regSetGPR: return SetGPRState(); |
| case e_regSetVFP: return SetVFPState(); |
| case e_regSetEXC: return SetEXCState(); |
| case e_regSetDBG: return SetDBGState(false); |
| default: break; |
| } |
| return KERN_INVALID_ARGUMENT; |
| } |
| |
| bool |
| DNBArchMachARM::RegisterSetStateIsValid (int set) const |
| { |
| return m_state.RegsAreValid(set); |
| } |
| |
| |
| nub_size_t |
| DNBArchMachARM::GetRegisterContext (void *buf, nub_size_t buf_len) |
| { |
| nub_size_t size = sizeof (m_state.context); |
| |
| if (buf && buf_len) |
| { |
| if (size > buf_len) |
| size = buf_len; |
| |
| bool force = false; |
| if (GetGPRState(force) | GetVFPState(force) | GetEXCState(force)) |
| return 0; |
| ::memcpy (buf, &m_state.context, size); |
| } |
| DNBLogThreadedIf (LOG_THREAD, "DNBArchMachARM::GetRegisterContext (buf = %p, len = %llu) => %llu", buf, (uint64_t)buf_len, (uint64_t)size); |
| // Return the size of the register context even if NULL was passed in |
| return size; |
| } |
| |
| nub_size_t |
| DNBArchMachARM::SetRegisterContext (const void *buf, nub_size_t buf_len) |
| { |
| nub_size_t size = sizeof (m_state.context); |
| if (buf == NULL || buf_len == 0) |
| size = 0; |
| |
| if (size) |
| { |
| if (size > buf_len) |
| size = buf_len; |
| |
| ::memcpy (&m_state.context, buf, size); |
| SetGPRState(); |
| SetVFPState(); |
| SetEXCState(); |
| } |
| DNBLogThreadedIf (LOG_THREAD, "DNBArchMachARM::SetRegisterContext (buf = %p, len = %llu) => %llu", buf, (uint64_t)buf_len, (uint64_t)size); |
| return size; |
| } |
| |
| |
| #endif // #if defined (__arm__) |
| |