include/configs/yellowstone.h - platform/external/u-boot - Gitiles

 /*
  *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  */

 /************************************************************************
  * yellowstone.h - configuration for YELLOWSTONE board
  ***********************************************************************/
 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*-----------------------------------------------------------------------
  * High Level Configuration Options
  *----------------------------------------------------------------------*/
 #define CONFIG_YELLOWSTONE			1	/* Board is BAMBOO	     */
 #define CONFIG_440_GR				1	/* Specific PPC440GR support */

 #define CONFIG_4xx					1	/* ... PPC4xx family	*/
 #define CONFIG_BOARD_EARLY_INIT_F	1   /* Call board_early_init_f	*/
 #undef	CFG_DRAM_TEST					/* disable - takes long time! */
 #define CONFIG_SYS_CLK_FREQ	66666666    /* external freq to pll	*/

 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
 #define CFG_SDRAM_BASE	    0x00000000	    /* _must_ be 0		    */
 #define CFG_FLASH_BASE	    0xf0000000	    /* start of FLASH		*/
 #define CFG_MONITOR_BASE    TEXT_BASE	    /* start of monitor		*/
 #define CFG_PCI_MEMBASE	    0xa0000000	    /* mapped pci memory	*/
 #define CFG_PCI_MEMBASE1    CFG_PCI_MEMBASE  + 0x10000000
 #define CFG_PCI_MEMBASE2    CFG_PCI_MEMBASE1 + 0x10000000
 #define CFG_PCI_MEMBASE3    CFG_PCI_MEMBASE2 + 0x10000000


 /*Don't change either of these*/
 #define CFG_PERIPHERAL_BASE 0xef600000	    /* internal peripherals	*/
 #define CFG_PCI_BASE	    0xe0000000	    /* internal PCI regs	*/
 /*Don't change either of these*/

 #define CFG_USB_DEVICE 0x50000000
 #define CFG_NVRAM_BASE_ADDR 0x80000000
 #define CFG_BCSR_BASE	    (CFG_NVRAM_BASE_ADDR | 0x2000)

 /*-----------------------------------------------------------------------
  * Initial RAM & stack pointer (placed in SDRAM)
  *----------------------------------------------------------------------*/
 #define CFG_INIT_RAM_ADDR	  0xf0000000		/* DCache */
 #define CFG_INIT_RAM_END	0x2000
 #define CFG_GBL_DATA_SIZE	256			/* num bytes initial data	*/
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET

 #define CFG_MONITOR_LEN	    (256 * 1024)    /* Reserve 256 kB for Mon	*/
 #define CFG_MALLOC_LEN	    (128 * 1024)    /* Reserve 128 kB for malloc*/
 #define CFG_KBYTES_SDRAM	( 128 * 1024)	/* 128MB		     */
 #define CFG_SDRAM_BANKS	    (2)
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #define CFG_EXT_SERIAL_CLOCK	11059200 /* use external 11.059MHz clk	*/
 #define CONFIG_BAUDRATE			9600
 #define CONFIG_SERIAL_MULTI   1
 /*define this if you want console on UART1*/
 #undef CONFIG_UART1_CONSOLE

 #define CFG_BAUDRATE_TABLE  \
     {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

 /*-----------------------------------------------------------------------
  * NVRAM/RTC
  *
  * NOTE: The RTC registers are located at 0x7FFF0 - 0x7FFFF
  * The DS1558 code assumes this condition
  *
  *----------------------------------------------------------------------*/
 #define CFG_NVRAM_SIZE	    (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */
 #define CONFIG_RTC_DS1556	1			 /* DS1556 RTC		*/

 /*-----------------------------------------------------------------------
  * FLASH related
  *----------------------------------------------------------------------*/
 #define CFG_MAX_FLASH_BANKS	1		    /* number of banks	    */
 #define CFG_MAX_FLASH_SECT	256		    /* sectors per device   */

 #undef	CFG_FLASH_CHECKSUM
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	120000	    /* Timeout for Flash Write (in ms)	*/

 /*-----------------------------------------------------------------------
  * DDR SDRAM
  *----------------------------------------------------------------------*/
 #undef CONFIG_SPD_EEPROM	       /* Don't use SPD EEPROM for setup    */

 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C		1	    /* I2C with hardware support	*/
 #undef	CONFIG_SOFT_I2C			    /* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
 #define CFG_I2C_SLAVE		0x7F


 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
 #undef	CFG_ENV_IS_IN_NVRAM		    /*No NVRAM on board*/
 #undef	CFG_ENV_IS_IN_FLASH		    /* ... not in flash		*/
 #define CFG_ENV_IS_IN_EEPROM 1

 /* Define to allow the user to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE

 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_ENV_SIZE		0x200	    /* Size of Environment vars */
 #define CFG_ENV_OFFSET		0x0
 #define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
 #define CFG_I2C_EEPROM_ADDR_LEN 1
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 #define CFG_EEPROM_PAGE_WRITE_BITS 3
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10

 #define CONFIG_BOOTCOMMAND	"bootm 0xfe000000"    /* autoboot command */
 #define CONFIG_BOOTDELAY	3		    /* disable autoboot */

 #define CONFIG_LOADS_ECHO		1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/

 #define CONFIG_MII			1	/* MII PHY management		*/
 #define CONFIG_NET_MULTI    1	/* required for netconsole  */
 #define CONFIG_PHY1_ADDR    3
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
 #define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
 #define CONFIG_NETMASK		255.255.255.0
 #define CONFIG_IPADDR		10.0.4.251
 #define CONFIG_ETHADDR		00:10:EC:00:12:34
 #define CONFIG_ETH1ADDR		00:10:EC:00:12:35

 #define CFG_RX_ETH_BUFFER	32	  /* Number of ethernet rx buffers & descriptors */
 #define CONFIG_SERVERIP		10.0.4.115

 /* Partitions */
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
 #define CONFIG_ISO_PARTITION

 #ifdef CONFIG_440_EP
 /* USB */
 #define CONFIG_USB_OHCI
 #define CONFIG_USB_STORAGE

 /*Comment this out to enable USB 1.1 device*/
 #define USB_2_0_DEVICE
 #endif /*CONFIG_440_EP*/

 #ifdef DEBUG
 #define CONFIG_PANIC_HANG
 #else
 #define CONFIG_HW_WATCHDOG			/* watchdog */
 #endif

 #ifdef CONFIG_440_EP
 	/* Need to define POST */
 #define CONFIG_COMMANDS	       ((CONFIG_CMD_DFL | \
 			CFG_CMD_DATE	|   \
 			CFG_CMD_DHCP	|   \
 			CFG_CMD_DIAG	|   \
 			CFG_CMD_ECHO	|   \
 			CFG_CMD_EEPROM	|   \
 			CFG_CMD_ELF	|   \
     /*	    CFG_CMD_EXT2    |*/ \
 	/*		CFG_CMD_FAT		|*/	\
 			CFG_CMD_I2C	|	\
 	/*		CFG_CMD_IDE		|*/	\
 			CFG_CMD_IRQ	|	\
     /*		CFG_CMD_KGDB	|*/	\
 			CFG_CMD_MII	|   \
 			CFG_CMD_PCI		|	\
 			CFG_CMD_PING	|	\
 			CFG_CMD_REGINFO |	\
 			CFG_CMD_SDRAM	|   \
 			CFG_CMD_FLASH	|   \
 	/*		CFG_CMD_SPI		|*/	\
 			CFG_CMD_USB	|	\
 			0 ) & ~CFG_CMD_IMLS)
 #else
 #define CONFIG_COMMANDS	       ((CONFIG_CMD_DFL | \
 			CFG_CMD_DATE	|   \
 			CFG_CMD_DHCP	|   \
 			CFG_CMD_DIAG	|   \
 			CFG_CMD_ECHO	|   \
 			CFG_CMD_EEPROM	|   \
 			CFG_CMD_ELF	|   \
     /*	    CFG_CMD_EXT2    |*/ \
 	/*		CFG_CMD_FAT		|*/	\
 			CFG_CMD_I2C	|	\
 	/*		CFG_CMD_IDE		|*/	\
 			CFG_CMD_IRQ	|	\
     /*		CFG_CMD_KGDB	|*/	\
 			CFG_CMD_MII	|   \
 			CFG_CMD_PCI		|	\
 			CFG_CMD_PING	|	\
 			CFG_CMD_REGINFO |	\
 			CFG_CMD_SDRAM	|   \
 			CFG_CMD_FLASH	|   \
 	/*		CFG_CMD_SPI		|*/	\
 			0 ) & ~CFG_CMD_IMLS)
 #endif

 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>

 /*
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/

 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

 #define CFG_LOAD_ADDR		0x100000	/* default load address */
 #define CFG_EXTBDINFO		    1	/* To use extended board_into (bd_t) */
 #define CONFIG_LYNXKDI		1   /* support kdi files */

 #define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */

 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
  */
 /* General PCI */
 #define CONFIG_PCI				    /* include pci support		*/
 #undef	CONFIG_PCI_PNP				/* do (not) pci plug-and-play	      */
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup	*/
 #define CFG_PCI_TARGBASE    0x80000000	/* PCIaddr mapped to CFG_PCI_MEMBASE */

 /* Board-specific PCI */
 #define CFG_PCI_PRE_INIT		/* enable board pci_pre_init()	*/
 #define CFG_PCI_TARGET_INIT
 #define CFG_PCI_MASTER_INIT

 #define CFG_PCI_SUBSYS_VENDORID 0x1014	/* IBM */
 #define CFG_PCI_SUBSYS_ID 0xcafe	/* Whatever */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
 #define CFG_DCACHE_SIZE		8192	/* For IBM 405 CPUs			*/
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
 #endif

 /*
  * Internal Definitions
  *
  * Boot Flags
  */
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/

 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
 #endif	/* __CONFIG_H */
	/*
	*
	* See file CREDITS for list of people who contributed to this
	* project.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	* MA 02111-1307 USA
	*/

	/************************************************************************
	* yellowstone.h - configuration for YELLOWSTONE board
	***********************************************************************/
	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*-----------------------------------------------------------------------
	* High Level Configuration Options
	----------------------------------------------------------------------/
	#define CONFIG_YELLOWSTONE 1 /* Board is BAMBOO */
	#define CONFIG_440_GR 1 /* Specific PPC440GR support */

	#define CONFIG_4xx 1 /* ... PPC4xx family */
	#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
	#undef CFG_DRAM_TEST /* disable - takes long time! */
	#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */

	/*-----------------------------------------------------------------------
	* Base addresses -- Note these are effective addresses where the
	* actual resources get mapped (not physical addresses)
	----------------------------------------------------------------------/
	#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
	#define CFG_FLASH_BASE 0xf0000000 /* start of FLASH */
	#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
	#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory */
	#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
	#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
	#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000


	/Don't change either of these/
	#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
	#define CFG_PCI_BASE 0xe0000000 /* internal PCI regs */
	/Don't change either of these/

	#define CFG_USB_DEVICE 0x50000000
	#define CFG_NVRAM_BASE_ADDR 0x80000000
	#define CFG_BCSR_BASE (CFG_NVRAM_BASE_ADDR \| 0x2000)

	/*-----------------------------------------------------------------------
	* Initial RAM & stack pointer (placed in SDRAM)
	----------------------------------------------------------------------/
	#define CFG_INIT_RAM_ADDR 0xf0000000 /* DCache */
	#define CFG_INIT_RAM_END 0x2000
	#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
	#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
	#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET

	#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
	#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
	#define CFG_KBYTES_SDRAM ( 128 * 1024) /* 128MB */
	#define CFG_SDRAM_BANKS (2)
	/*-----------------------------------------------------------------------
	* Serial Port
	----------------------------------------------------------------------/
	#undef CONFIG_SERIAL_SOFTWARE_FIFO
	#define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */
	#define CONFIG_BAUDRATE 9600
	#define CONFIG_SERIAL_MULTI 1
	/define this if you want console on UART1/
	#undef CONFIG_UART1_CONSOLE

	#define CFG_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

	/*-----------------------------------------------------------------------
	* NVRAM/RTC
	*
	* NOTE: The RTC registers are located at 0x7FFF0 - 0x7FFFF
	* The DS1558 code assumes this condition
	*
	----------------------------------------------------------------------/
	#define CFG_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */
	#define CONFIG_RTC_DS1556 1 /* DS1556 RTC */

	/*-----------------------------------------------------------------------
	* FLASH related
	----------------------------------------------------------------------/
	#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
	#define CFG_MAX_FLASH_SECT 256 /* sectors per device */

	#undef CFG_FLASH_CHECKSUM
	#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
	#define CFG_FLASH_WRITE_TOUT 120000 /* Timeout for Flash Write (in ms) */

	/*-----------------------------------------------------------------------
	* DDR SDRAM
	----------------------------------------------------------------------/
	#undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */

	/*-----------------------------------------------------------------------
	* I2C
	----------------------------------------------------------------------/
	#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
	#undef CONFIG_SOFT_I2C /* I2C bit-banged */
	#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
	#define CFG_I2C_SLAVE 0x7F


	/*-----------------------------------------------------------------------
	* Environment
	----------------------------------------------------------------------/
	#undef CFG_ENV_IS_IN_NVRAM /No NVRAM on board/
	#undef CFG_ENV_IS_IN_FLASH /* ... not in flash */
	#define CFG_ENV_IS_IN_EEPROM 1

	/* Define to allow the user to overwrite serial and ethaddr */
	#define CONFIG_ENV_OVERWRITE

	#define CFG_I2C_MULTI_EEPROMS
	#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */
	#define CFG_ENV_OFFSET 0x0
	#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
	#define CFG_I2C_EEPROM_ADDR_LEN 1
	#define CFG_EEPROM_PAGE_WRITE_ENABLE
	#define CFG_EEPROM_PAGE_WRITE_BITS 3
	#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10

	#define CONFIG_BOOTCOMMAND "bootm 0xfe000000" /* autoboot command */
	#define CONFIG_BOOTDELAY 3 /* disable autoboot */

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */

	#define CONFIG_MII 1 /* MII PHY management */
	#define CONFIG_NET_MULTI 1 /* required for netconsole */
	#define CONFIG_PHY1_ADDR 3
	#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
	#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
	#define CONFIG_NETMASK 255.255.255.0
	#define CONFIG_IPADDR 10.0.4.251
	#define CONFIG_ETHADDR 00:10:EC:00:12:34
	#define CONFIG_ETH1ADDR 00:10:EC:00:12:35

	#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
	#define CONFIG_SERVERIP 10.0.4.115

	/* Partitions */
	#define CONFIG_MAC_PARTITION
	#define CONFIG_DOS_PARTITION
	#define CONFIG_ISO_PARTITION

	#ifdef CONFIG_440_EP
	/* USB */
	#define CONFIG_USB_OHCI
	#define CONFIG_USB_STORAGE

	/Comment this out to enable USB 1.1 device/
	#define USB_2_0_DEVICE
	#endif /CONFIG_440_EP/

	#ifdef DEBUG
	#define CONFIG_PANIC_HANG
	#else
	#define CONFIG_HW_WATCHDOG /* watchdog */
	#endif

	#ifdef CONFIG_440_EP
	/* Need to define POST */
	#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \| \
	CFG_CMD_DATE \| \
	CFG_CMD_DHCP \| \
	CFG_CMD_DIAG \| \
	CFG_CMD_ECHO \| \
	CFG_CMD_EEPROM \| \
	CFG_CMD_ELF \| \
	/* CFG_CMD_EXT2 \|*/ \
	/* CFG_CMD_FAT \|*/ \
	CFG_CMD_I2C \| \
	/* CFG_CMD_IDE \|*/ \
	CFG_CMD_IRQ \| \
	/* CFG_CMD_KGDB \|*/ \
	CFG_CMD_MII \| \
	CFG_CMD_PCI \| \
	CFG_CMD_PING \| \
	CFG_CMD_REGINFO \| \
	CFG_CMD_SDRAM \| \
	CFG_CMD_FLASH \| \
	/* CFG_CMD_SPI \|*/ \
	CFG_CMD_USB \| \
	0 ) & ~CFG_CMD_IMLS)
	#else
	#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \| \
	CFG_CMD_DATE \| \
	CFG_CMD_DHCP \| \
	CFG_CMD_DIAG \| \
	CFG_CMD_ECHO \| \
	CFG_CMD_EEPROM \| \
	CFG_CMD_ELF \| \
	/* CFG_CMD_EXT2 \|*/ \
	/* CFG_CMD_FAT \|*/ \
	CFG_CMD_I2C \| \
	/* CFG_CMD_IDE \|*/ \
	CFG_CMD_IRQ \| \
	/* CFG_CMD_KGDB \|*/ \
	CFG_CMD_MII \| \
	CFG_CMD_PCI \| \
	CFG_CMD_PING \| \
	CFG_CMD_REGINFO \| \
	CFG_CMD_SDRAM \| \
	CFG_CMD_FLASH \| \
	/* CFG_CMD_SPI \|*/ \
	0 ) & ~CFG_CMD_IMLS)
	#endif

	/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
	#include <cmd_confdefs.h>

	/*
	* Miscellaneous configurable options
	*/
	#define CFG_LONGHELP /* undef to save memory */
	#define CFG_PROMPT "=> " /* Monitor Command Prompt */
	#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
	#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
	#define CFG_MAXARGS 16 /* max number of command args */
	#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */

	#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
	#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */

	#define CFG_LOAD_ADDR 0x100000 /* default load address */
	#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
	#define CONFIG_LYNXKDI 1 /* support kdi files */

	#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */

	/*-----------------------------------------------------------------------
	* PCI stuff
	*-----------------------------------------------------------------------
	*/
	/* General PCI */
	#define CONFIG_PCI /* include pci support */
	#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */
	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */

	/* Board-specific PCI */
	#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */
	#define CFG_PCI_TARGET_INIT
	#define CFG_PCI_MASTER_INIT

	#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
	#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
	/*-----------------------------------------------------------------------
	* Cache Configuration
	*/
	#define CFG_DCACHE_SIZE 8192 /* For IBM 405 CPUs */
	#define CFG_CACHELINE_SIZE 32 /* ... */
	#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
	#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
	#endif

	/*
	* Internal Definitions
	*
	* Boot Flags
	*/
	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	#define BOOTFLAG_WARM 0x02 /* Software reboot */

	#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
	#endif
	#endif /* __CONFIG_H */