blob: a139590be8494088f8d95a586b2578d6205b9bac [file] [log] [blame]
/*
* (C) Copyright 2001
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_SBC405 1 /* ...on a WR SBC405 board */
#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
#define CONFIG_BAUDRATE 9600
#define CONFIG_PREBOOT "echo;echo Welcome to U-Boot for the sbc405;echo;echo Type \"? or help\" to get on-line help;echo"
#define CONFIG_RAMBOOT \
"setenv bootargs root=/dev/ram rw nfsroot=${serverip}:${rootpath} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
"bootm ffc00000 ffca0000"
#define CONFIG_NFSBOOT \
"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
"bootm ffc00000"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND "version;echo;tftpboot ${loadaddr} ${loadfile};bootvx" /* autoboot command */
#define CONFIG_PPC4xx_EMAC
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_PHY_RESET_DELAY 300 /* Intel LXT971A needs this */
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootargs=emac(0,0)host:/T221ppc/target/config/sbc405/vxWorks.st " \
"e=192.168.193.102:ffffffe0 h=192.168.193.100 u=target pw=hello " \
"f=0x08 tn=sbc405 o=emac \0" \
"env_startaddr=FF000000\0" \
"env_endaddr=FF03FFFF\0" \
"loadfile=vxWorks.st\0" \
"loadaddr=0x01000000\0" \
"net_load=tftpboot ${loadaddr} ${loadfile}\0" \
"uboot_startaddr=FFFC0000\0" \
"uboot_endaddr=FFFFFFFF\0" \
"update=tftp ${loadaddr} u-boot.bin;" \
"protect off ${uboot_startaddr} ${uboot_endaddr};" \
"era ${uboot_startaddr} ${uboot_endaddr};" \
"cp.b ${loadaddr} ${uboot_startaddr} ${filesize};" \
"protect on ${uboot_startaddr} ${uboot_endaddr}\0" \
"zapenv=protect off ${env_startaddr} ${env_endaddr};" \
"era ${env_startaddr} ${env_endaddr};" \
"protect on ${env_startaddr} ${env_endaddr}\0"
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_ENV_OVERWRITE
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_BSP
#define CONFIG_CMD_ELF
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PING
#define CONFIG_CMD_SDRAM
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
#define CONFIG_ETHADDR DE:AD:BE:EF:01:01 /* Ethernet address */
#define CONFIG_IPADDR 192.168.193.102
#define CONFIG_NETMASK 255.255.255.224
#define CONFIG_SERVERIP 192.168.193.119
#define CONFIG_GATEWAYIP 192.168.193.97
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
#define CONFIG_SYS_BASE_BAUD 691200
/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_info (bd_t) */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_PPC4XX
#define CONFIG_SYS_I2C_PPC4XX_CH0
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
#define PCI_HOST_FORCE 1 /* configure as pci host */
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
/* resource configuration */
#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0408 /* PCI Device ID: PMC-405 */
#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_MONITOR_BASE 0xFFFC0000
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_FLASH_BASE 0xFF000000
#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Flash Erase Timeout (in ms) */
#define CONFIG_SYS_FLASH_INCREMENT 0x01000000
#undef CONFIG_SYS_FLASH_PROTECTION /* don't use hardware protection */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
/*-----------------------------------------------------------------------
* Environment Variable setup
*/
#define CONFIG_ENV_ADDR CONFIG_SYS_FLASH_BASE /* starting right at the beginning */
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_OFFSET 0 /* starting right at the beginning */
#define CONFIG_ENV_SECT_SIZE 0x40000 /* see README - env sector total size */
#define CONFIG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*/
#define FLASH0_BA CONFIG_SYS_FLASH_BASE /* FLASH 0 Base Address */
/* Memory Bank 0 (Flash Bank 0) initialization */
#define CONFIG_SYS_EBC_PB0AP 0x92015480
#define CONFIG_SYS_EBC_PB0CR FLASH0_BA | 0x9C000 /* BAS=0xFF0,BS=16MB,BU=R/W,BW=32bit*/
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
#define CONFIG_SYS_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Definitions for Serial Presence Detect EEPROM address
* (to get SDRAM settings)
*/
#define SPD_EEPROM_ADDRESS 0x50
#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
#endif /* __CONFIG_H */