blob: 35b045127cb872462483f76d4629a03724ce9229 [file] [log] [blame]
/*
* (C) Copyright 2003
* Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
*
* Configuation settings for the IXDP425 board.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_IXP425 1 /* This is an IXP425 CPU */
#define CONFIG_IXDP425 1 /* on an IXDP425 Board */
#define CONFIG_DISPLAY_CPUINFO 1 /* display cpu info (and speed) */
#define CONFIG_DISPLAY_BOARDINFO 1 /* display board info */
/***************************************************************
* U-boot generic defines start here.
***************************************************************/
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAUDRATE 115200
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ELF
#define CONFIG_CMD_PCI
#define CONFIG_PCI
#define CONFIG_NET_MULTI
#define CONFIG_EEPRO100
#define CONFIG_BOOTDELAY 3
/*#define CONFIG_ETHADDR 08:00:3e:26:0a:5b*/
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_IPADDR 192.168.0.21
#define CONFIG_SERVERIP 192.168.0.148
#define CONFIG_BOOTCOMMAND "bootm 50040000"
#define CONFIG_BOOTARGS "root=/dev/mtdblock2 rootfstype=cramfs console=ttyS0,115200"
#define CONFIG_CMDLINE_TAG
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 4 ... 8 MB in DRAM */
#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */
#define CONFIG_SYS_LOAD_ADDR 0x00010000 /* default load address */
#define CONFIG_SYS_HZ 3333333 /* spec says 66.666 MHz, but it appears to be 33 */
/* valid baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Stack sizes
*
* The stack sizes are set up in start.S using the settings below
*/
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
#ifdef CONFIG_USE_IRQ
#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
#endif
/***************************************************************
* Platform/Board specific defines start here.
***************************************************************/
/*
* Hardware drivers
*/
/*
* select serial console configuration
*/
#define CONFIG_SYS_IXP425_CONSOLE IXP425_UART1 /* we use UART1 for console */
/*
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1 /* we have 2 banks of DRAM */
#define PHYS_SDRAM_1 0x00000000 /* SDRAM Bank #1 */
#define PHYS_SDRAM_1_SIZE 0x01000000 /* 16 MB */
#define PHYS_FLASH_1 0x50000000 /* Flash Bank #1 */
#define PHYS_FLASH_SIZE 0x00800000 /* 8 MB */
#define PHYS_FLASH_BANK_SIZE 0x00800000 /* 8 MB Banks */
#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 128 KB sectors (x1) */
#define CONFIG_SYS_DRAM_BASE 0x00000000
#define CONFIG_SYS_DRAM_SIZE 0x01000000
#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
/*
* Expansion bus settings
*/
#define CONFIG_SYS_EXP_CS0 0xbcd23c42
/*
* SDRAM settings
*/
#define CONFIG_SYS_SDR_CONFIG 0xd
#define CONFIG_SYS_SDR_MODE_CONFIG 0x1
#define CONFIG_SYS_SDRAM_REFRESH_CNT 0x81a
/*
* GPIO settings
*/
/*
* FLASH and environment organization
*/
/*
* FLASH and environment organization
*/
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1 }
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT /* no byte writes on IXP4xx */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + 0x20000)
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
#endif /* __CONFIG_H */