| /* |
| * Copyright 2017 The Android Open Source Project |
| * |
| * Licensed under the Apache License, Version 2.0 (the "License"); |
| * you may not use this file except in compliance with the License. |
| * You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, software |
| * distributed under the License is distributed on an "AS IS" BASIS, |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| * See the License for the specific language governing permissions and |
| * limitations under the License. |
| */ |
| |
| #pragma once |
| |
| #include "bluetooth_headset_callbacks.h" |
| #include "bt_hf.h" |
| |
| namespace bluetooth { |
| namespace headset { |
| |
| /** |
| * Programming interface for Headset profiles in the Fluoride stack |
| * Thread-safe |
| */ |
| class Interface { |
| public: |
| virtual ~Interface() = default; |
| /** |
| * Register the BtHf callbacks |
| * |
| * @param callbacks callbacks for the user of the native stack |
| * @param max_hf_clients maximum number of headset clients |
| * @param inband_ringing_enabled whether inband ringtone is enabled |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t Init(Callbacks* callbacks, int max_hf_clients, |
| bool inband_ringing_enabled) = 0; |
| |
| /** |
| * Connect to headset |
| * |
| * @param bd_addr remote device address |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t Connect(RawAddress* bd_addr) = 0; |
| |
| /** |
| * Disconnect from headset |
| * |
| * @param bd_addr remote device address |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t Disconnect(RawAddress* bd_addr) = 0; |
| |
| /** |
| * Create an audio connection |
| * |
| * @param bd_addr remote device address |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t ConnectAudio(RawAddress* bd_addr) = 0; |
| |
| /** |
| * Close the audio connection |
| * |
| * @param bd_addr remote device address |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t DisconnectAudio(RawAddress* bd_addr) = 0; |
| |
| /** start voice recognition */ |
| /** |
| * Start voice recognition |
| * @param bd_addr remote device address |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t StartVoiceRecognition(RawAddress* bd_addr) = 0; |
| |
| /** |
| * Stop voice recognition |
| * |
| * @param bd_addr remote device address |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t StopVoiceRecognition(RawAddress* bd_addr) = 0; |
| |
| /** |
| * Change HFP related volume on remote headset |
| * |
| * @param type Speaker (+VGS) or Mic (+VGM) |
| * @param volume volume level on scale from 0 to 15, p69, HFP 1.7.1 spec |
| * @param bd_addr remote device address |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t VolumeControl(bthf_volume_type_t type, int volume, |
| RawAddress* bd_addr) = 0; |
| |
| /** |
| * Combined device status change notification |
| * |
| * @param ntk_state Network state, available or not available |
| * @param svc_type Service type, roaming or home |
| * @param signal Signal strength, 0 to 5, p86, HFP 1.7.1 spec |
| * @param batt_chg Battery level of the phone, 0 to 5, p87, HFP 1.7.1 spec |
| * @param bd_addr remote device address |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t DeviceStatusNotification(bthf_network_state_t ntk_state, |
| bthf_service_type_t svc_type, |
| int signal, int batt_chg, |
| RawAddress* bd_addr) = 0; |
| |
| /** |
| * Response for COPS (Query Operator Selection) command |
| * |
| * @param cops Operator Name, max length 16 char, p32 HFP 1.7.1 spec |
| * @param bd_addr remote device address |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t CopsResponse(const char* cops, RawAddress* bd_addr) = 0; |
| |
| /** |
| * Response for CIND (Stanford Indicator Update) command |
| * |
| * @param svc service availability, available or not available |
| * @param num_active number of active calls |
| * @param num_held number of held calls |
| * @param call_setup_state call setup state |
| * @param signal signal strength, 0 to 5, p86 HFP 1.7.1 spec |
| * @param roam roaming state, 1 for roaming, 0 for home, p86 HFP 1.7.1 spec |
| * @param batt_chg AG battery charge, 0 to 5, p87 HFP 1.7.1 spec |
| * @param bd_addr remote device address |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t CindResponse(int svc, int num_active, int num_held, |
| bthf_call_state_t call_setup_state, |
| int signal, int roam, int batt_chg, |
| RawAddress* bd_addr) = 0; |
| |
| /** |
| * Pre-formatted AT response, typically in response to unknown AT cmd |
| * |
| * @param rsp formatted AT response |
| * @param bd_addr remote device address |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t FormattedAtResponse(const char* rsp, |
| RawAddress* bd_addr) = 0; |
| |
| /** |
| * ok/error response to AT commands |
| * |
| * @param response_code OK or ERROR |
| * @param error_code actual error code depend on use case |
| * @param bd_addr remote device address |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t AtResponse(bthf_at_response_t response_code, |
| int error_code, RawAddress* bd_addr) = 0; |
| |
| /** |
| * Response for CLCC (Current List of Calls) command. |
| * Can be iteratively called for each call index |
| * Call index of 0 will be treated as NULL termination (Completes response) |
| * |
| * @param index index of the call |
| * @param dir direction of the call |
| * @param state state of the call |
| * @param mode mode of the call |
| * @param mpty whether the call is multi party |
| * @param number phone number of the call |
| * @param type type of the call |
| * @param bd_addr remote device address |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t ClccResponse( |
| int index, bthf_call_direction_t dir, bthf_call_state_t state, |
| bthf_call_mode_t mode, bthf_call_mpty_type_t mpty, const char* number, |
| bthf_call_addrtype_t type, RawAddress* bd_addr) = 0; |
| |
| /** |
| * Notify of a call state change |
| * Each update notifies |
| * 1. Number of active/held/ringing calls |
| * 2. call_state: This denotes the state change that triggered this msg |
| * This will take one of the values from BtHfCallState |
| * 3. number & type: valid only for incoming & waiting call |
| * |
| * @param num_active number of active calls |
| * @param num_held number of held calls |
| * @param call_setup_state current call setup state |
| * @param number phone number of the call |
| * @param type type of the call |
| * @param name caller display name |
| * @param bd_addr remote device address |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t PhoneStateChange(int num_active, int num_held, |
| bthf_call_state_t call_setup_state, |
| const char* number, |
| bthf_call_addrtype_t type, |
| const char* name, |
| RawAddress* bd_addr) = 0; |
| |
| /** |
| * Closes the interface. |
| */ |
| virtual void Cleanup() = 0; |
| |
| /** |
| * Whether we are allowed to initiate SCO |
| * |
| * @param value true to allow, false to disallow |
| * @return BT_STATUS_SUCCESS on success |
| */ |
| virtual bt_status_t SetScoAllowed(bool value) = 0; |
| |
| /** |
| * Send +BSIR response code to enable/disable in-band ringtone in an active |
| * HFP service level connection |
| * |
| * @param value true for enabled, false for disable |
| * @param bd_addr remote device address |
| */ |
| virtual bt_status_t SendBsir(bool value, RawAddress* bd_addr) = 0; |
| |
| /** |
| * Set the current active headset device for SCO audio |
| * |
| * @param active_device_addr remote device address |
| */ |
| virtual bt_status_t SetActiveDevice(RawAddress* active_device_addr) = 0; |
| }; |
| |
| } // namespace headset |
| } // namespace bluetooth |