| ## This file is used by NFC NXP NCI HAL(external/libnfc-nci/halimpl/pn547) |
| ## and NFC Service Java Native Interface Extensions (packages/apps/Nfc/nci/jni/extns/pn547) |
| ############################################################################### |
| # Application options |
| # Logging Levels |
| # NXPLOG_DEFAULT_LOGLEVEL 0x01 |
| # ANDROID_LOG_DEBUG 0x03 |
| # ANDROID_LOG_WARN 0x02 |
| # ANDROID_LOG_ERROR 0x01 |
| # ANDROID_LOG_SILENT 0x00 |
| NXPLOG_EXTNS_LOGLEVEL=0x03 |
| NXPLOG_NCIHAL_LOGLEVEL=0x03 |
| NXPLOG_NCIX_LOGLEVEL=0x03 |
| NXPLOG_NCIR_LOGLEVEL=0x03 |
| NXPLOG_FWDNLD_LOGLEVEL=0x03 |
| NXPLOG_TML_LOGLEVEL=0x03 |
| NFC_DEBUG_ENABLED=0x01 |
| |
| ############################################################################### |
| # Nfc Device Node name |
| NXP_NFC_DEV_NODE="/dev/pn553" |
| |
| ############################################################################### |
| # Extension for Mifare reader enable |
| MIFARE_READER_ENABLE=0x01 |
| |
| ############################################################################### |
| # Mifare Reader implementation |
| # 0: General implementation |
| # 1: Legacy implementation |
| LEGACY_MIFARE_READER=0 |
| |
| ############################################################################### |
| # Vzw Feature enable |
| VZW_FEATURE_ENABLE=0x01 |
| |
| ############################################################################### |
| # File name for Firmware |
| NXP_FW_NAME="libpn557_fw.so" |
| |
| ############################################################################### |
| # System clock source selection configuration |
| #define CLK_SRC_XTAL 1 |
| #define CLK_SRC_PLL 2 |
| NXP_SYS_CLK_SRC_SEL=0x02 |
| |
| ############################################################################### |
| # System clock frequency selection configuration |
| #define CLK_FREQ_13MHZ 1 |
| #define CLK_FREQ_19_2MHZ 2 |
| #define CLK_FREQ_24MHZ 3 |
| #define CLK_FREQ_26MHZ 4 |
| #define CLK_FREQ_38_4MHZ 5 |
| #define CLK_FREQ_52MHZ 6 |
| NXP_SYS_CLK_FREQ_SEL=0x02 |
| |
| ############################################################################### |
| # The timeout value to be used for clock request acknowledgment |
| # min value = 0x01 to max = 0x06 |
| NXP_SYS_CLOCK_TO_CFG=0x06 |
| |
| ############################################################################### |
| # NXP proprietary settings |
| NXP_ACT_PROP_EXTN={2F, 02, 00} |
| |
| ############################################################################### |
| # NFC forum profile settings |
| NXP_NFC_PROFILE_EXTN={20, 02, 05, 01, A0, 44, 01, 00} |
| |
| ############################################################################### |
| # NXP TVDD configurations settings |
| # Allow NFCC to configure External TVDD, two configurations (1 and 2) supported, |
| # out of them only one can be configured at a time. |
| NXP_EXT_TVDD_CFG=0x02 |
| |
| ############################################################################### |
| #config1:SLALM, 3.3V for both RM and CM |
| NXP_EXT_TVDD_CFG_1={20, 02, 0F, 01, A0, 0E, 0B, 31, 01, 01, 31, 00, 00, 00, 01, 00, D0, 0C} |
| |
| ############################################################################### |
| #config2: use DCDC in CE, use Tx_Pwr_Req, set CFG2 mode, SLALM, |
| #monitoring 5V from DCDC, 3.3V for both RM and CM, DCDCWaitTime=4.2ms |
| NXP_EXT_TVDD_CFG_2={20, 02, 0F, 01, A0, 0E, 0B, 11, 01, C2, B2, 00, B2, 1E, 1F, 00, D0, 0C} |
| |
| |
| ############################################################################### |
| # Set configuration optimization decision setting |
| # Enable = 0x01 |
| # Disable = 0x00 |
| NXP_SET_CONFIG_ALWAYS=0x01 |
| |
| ############################################################################### |
| # Core configuration rf field filter settings to enable set to 01 to disable set |
| # to 00 last bit |
| NXP_CORE_RF_FIELD={ 20, 02, 05, 01, A0, 62, 01, 00 } |
| |
| ############################################################################### |
| # To enable i2c fragmentation set i2c fragmentation enable 0x01 to disable set |
| # to 0x00 |
| NXP_I2C_FRAGMENTATION_ENABLED=0x00 |
| |
| ############################################################################### |
| # Mifare Classic Key settings |
| #NXP_CORE_MFCKEY_SETTING={20, 02, 25,04, A0, 51, 06, A0, A1, A2, A3, A4, A5, |
| # A0, 52, 06, D3, F7, D3, F7, D3, F7, |
| # A0, 53, 06, FF, FF, FF, FF, FF, FF, |
| # A0, 54, 06, 00, 00, 00, 00, 00, 00} |
| |
| ############################################################################### |
| # Force ESE to only listen to the following technology(s). |
| # The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. |
| # Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | NFA_TECHNOLOGY_MASK_F |
| NXP_ESE_LISTEN_TECH_MASK=0x07 |
| |
| ############################################################################### |
| #Enable SWP full power mode when phone is power off |
| NXP_SWP_FULL_PWR_ON=0x00 |
| |
| ############################################################################### |
| #### Select the CHIP #### |
| #PN547C2 0x01 |
| #PN65T 0x02 |
| #PN548AD 0x03 |
| #PN66T 0x04 |
| #PN551 0x05 |
| #PN67T 0x06 |
| #PN553 0x07 |
| #PN80T 0x08 |
| NXP_NFC_CHIP=0x08 |
| |
| ############################################################################### |
| # CE when Screen state is locked |
| # This setting is for DEFAULT_AID_ROUTE, |
| # DEFAULT_DESFIRE_ROUTE and DEFAULT_MIFARE_CLT_ROUTE |
| # Disable 0x00 |
| # Enable 0x01 |
| NXP_CE_ROUTE_STRICT_DISABLE=0x01 |
| |
| ############################################################################### |
| #Timeout in secs to get NFCEE Discover notification |
| NXP_DEFAULT_NFCEE_DISC_TIMEOUT=20 |
| |
| ############################################################################### |
| NXP_DEFAULT_NFCEE_TIMEOUT=20 |
| |
| ############################################################################### |
| #Timeout in secs |
| NXP_SWP_RD_TAG_OP_TIMEOUT=0x20 |
| |
| ############################################################################### |
| #Set the default AID route Location : |
| #This settings will be used when application does not set this parameter |
| # host 0x00 |
| # eSE 0x01 |
| # UICC 0x02 |
| DEFAULT_AID_ROUTE=0x00 |
| |
| ############################################################################### |
| # Configure the default NfcA/IsoDep techology and protocol route. Can be |
| # either a secure element (e.g. 0xF4) or the host (0x00) |
| # host 0x00 |
| # eSE 0x01 |
| # UICC 0x02 |
| DEFAULT_ISODEP_ROUTE=0x00 |
| |
| ############################################################################### |
| # Configure the single default SE to use. The default is to use the first |
| # SE that is detected by the stack. This value might be used when the phone |
| # supports multiple SE (e.g. 0xC0 and 0x80) but you want to force it to use |
| # one of them (e.g. 0xC0). |
| # host 0x00 |
| # eSE 0x01 |
| # UICC 0x02 |
| DEFAULT_OFFHOST_ROUTE=0x01 |
| |
| ############################################################################### |
| # Configure the single default SE to use. The default is to use the first |
| # SE that is detected by the stack. This value might be used when the phone |
| # supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use |
| # one of them (e.g. 0xF4). |
| # host 0x00 |
| # eSE 0x01 |
| # UICC 0x02 |
| DEFAULT_TECH_ABF_ROUTE=0x01 |
| |
| ############################################################################### |
| #Set the default Felica T3T System Code OffHost route Location : |
| #This settings will be used when application does not set this parameter |
| # host 0x00 |
| # eSE 0x01 |
| DEFAULT_SYS_CODE_ROUTE=0x01 |
| |
| ############################################################################### |
| #Set the default AID Power state : |
| #This settings will be used when application does not set this parameter |
| # bit pos 0 = Switch On |
| # bit pos 1 = Switch Off |
| # bit pos 2 = Battery Off |
| # bit pos 3 = Switched On Sub-State 1 : Screen is off and device is unlocked |
| # bit pos 4 = Switched On Sub-State 2 : Screen is on and device is locked |
| # bit pos 5 = Switched On Sub-State 3 : Screen is off and device is locked |
| DEFAULT_AID_PWR_STATE=0x39 |
| |
| ############################################################################### |
| #Set the Mifare Desfire Power state : |
| #This settings will be used when application does not set this parameter |
| # bit pos 0 = Switch On |
| # bit pos 1 = Switch Off |
| # bit pos 2 = Battery Off |
| # bit pos 3 = Switched On Sub-State 1 : Screen is off and device is unlocked |
| # bit pos 4 = Switched On Sub-State 2 : Screen is on and device is locked |
| # bit pos 5 = Switched On Sub-State 3 : Screen is off and device is locked |
| DEFAULT_ISODEP_PWR_STATE=0x3B |
| |
| ############################################################################### |
| #Set the Mifare CLT Power state : |
| #This settings will be used when application does not set this parameter |
| # bit pos 0 = Switch On |
| # bit pos 1 = Switch Off |
| # bit pos 2 = Battery Off |
| # bit pos 3 = Switched On Sub-State 1 : Screen is off and device is unlocked |
| # bit pos 4 = Switched On Sub-State 2 : Screen is on and device is locked |
| # bit pos 5 = Switched On Sub-State 3 : Screen is off and device is locked |
| DEFAULT_OFFHOST_PWR_STATE=0x3B |
| |
| ############################################################################### |
| #Set Tech A,B,F Power state : |
| #This settings will be used when application does not set this parameter |
| # bit pos 0 = Switch On |
| # bit pos 1 = Switch Off |
| # bit pos 2 = Battery Off |
| # bit pos 3 = Switched On Sub-State 1 : Screen is off and device is unlocked |
| # bit pos 4 = Switched On Sub-State 2 : Screen is on and device is locked |
| # bit pos 5 = Switched On Sub-State 3 : Screen is off and device is locked |
| DEFAULT_TECH_ABF_PWR_STATE=0x3B |
| |
| ############################################################################### |
| #Set the SYS_CODE Power state : |
| #This settings will be used when application does not set this parameter |
| # bit pos 0 = Switch On |
| # bit pos 1 = Switch Off |
| # bit pos 2 = Battery Off |
| # bit pos 3 = Switched On Sub-State 1 : Screen is off and device is unlocked |
| # bit pos 4 = Switched On Sub-State 2 : Screen is on and device is locked |
| # bit pos 5 = Switched On Sub-State 3 : Screen is off and device is locked |
| DEFAULT_SYS_CODE_PWR_STATE=0x00 |
| |
| ############################################################################### |
| # Configure the NFC Extras to open and use a static pipe. If the value is |
| # not set or set to 0, then the default is use a dynamic pipe based on a |
| # destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value |
| # for each UICC (where F3="UICC0" and F4="UICC1") |
| OFF_HOST_ESE_PIPE_ID=0x19 |
| OFF_HOST_SIM_PIPE_ID=0x0A |
| |
| ############################################################################### |
| # Bail out mode |
| # If set to 1, NFCC is using bail out mode for either Type A or Type B poll. |
| NFA_POLL_BAIL_OUT_MODE=0x01 |
| |
| ############################################################################### |
| # AID Matching platform options |
| # AID_MATCHING_L 0x01 |
| # AID_MATCHING_K 0x02 |
| AID_MATCHING_PLATFORM=0x01 |
| |
| ############################################################################### |
| #CHINA_TIANJIN_RF_SETTING |
| #Enable 0x01 |
| #Disable 0x00 |
| NXP_CHINA_TIANJIN_RF_ENABLED=0x01 |
| |
| ############################################################################### |
| #SWP_SWITCH_TIMEOUT_SETTING |
| # Allowed range of swp timeout setting is 0x00 to 0x3C [0 - 60]. |
| # Timeout in milliseconds, for example |
| # No Timeout 0x00 |
| # 10 millisecond timeout 0x0A |
| NXP_SWP_SWITCH_TIMEOUT=0x0A |
| |
| ############################################################################### |
| # interface options for JCOP Download |
| # Disabled 0x00 |
| # NFC 0x01 |
| # SPI 0x02 |
| NXP_ESE_JCOP_DEFAULT_INTERFACE=0x00 |
| |
| ############################################################################### |
| # Loader service version |
| # NFC service checks for LS version 2.0 or 2.1 |
| # LS2.0 0x20 |
| # LS2.1 0x21 |
| # LS2.2 0x22 |
| # AT NFC service intialization |
| NXP_LOADER_SERVICE_VERSION=0x22 |
| |
| ############################################################################### |
| #Timeout value in milliseconds for NFCC standby mode.The range is between 5000 |
| #msec to 20000 msec and zero is to disable. |
| NXP_NFCC_STANDBY_TIMEOUT=20000 |
| |
| ############################################################################### |
| #Dynamic RSSI feature enable |
| # Disable 0x00 |
| # Enable 0x01 |
| NXP_AGC_DEBUG_ENABLE=0x00 |
| |
| ############################################################################### |
| #Virtual Mode ESE and Wired Mode ongoing delay Wired Mode |
| # For Technology routing to ESE Technology Mask = 4 |
| # For ISO-DEP Protocol routing to ESE Mask = 2 |
| # It can also take TECH|PROTO = 6 |
| # To ignore the delay set mask to = 0 |
| NXP_ESE_WIRED_PRT_MASK=0x00 |
| |
| ############################################################################### |
| #Virtual Mode UICC and Wired Mode ongoing delay Wired Mode |
| #For Technology routing to UICC Technology Mask = 4 |
| #For ISO-DEP Protocol routing to UICC set Mask = 2 |
| #For Select AID Routing to UICC set Mask = 1 |
| #It can also take values TECH|PROTO|SELECT_AID = 7 , 6 , 5 ,3 .To ignore delay |
| #set mask = 0 |
| NXP_UICC_WIRED_PRT_MASK=0x00 |
| |
| ################################################################################ |
| #RF field true delay Wired Mode |
| # delay wired mode = 1 |
| # allow wired mode = 0 |
| NXP_WIRED_MODE_RF_FIELD_ENABLE=0x00 |
| |
| ############################################################################### |
| #Config to allow adding aids |
| #NFC on/off is required after this config |
| #1 = enabling adding aid to NFCC routing table. |
| #0 = disabling adding aid to NFCC routing table. |
| NXP_ENABLE_ADD_AID=0x01 |
| |
| ############################################################################### |
| # JCOP-3.3 continuous process timeout in msec and value should be in Hexadecimal |
| # JCOP CP TIMEOUT |
| NXP_CP_TIMEOUT={00, 77} |
| |
| ############################################################################### |
| # SVDD sync off Delay in ms it can be max 20 ms |
| # If out of range timeout used, default delay of 10ms will be set |
| NXP_SVDD_SYNC_OFF_DELAY=10 |
| |
| ############################################################################### |
| #NXP_CN_TRANSIT_CMA_BYPASSMODE_ENABLE |
| #Enable this config it prevents EMVCo PICC compliancy and Mifare backward compatibility works |
| #Disable this config EMVCo PICC compliancy works and Mifare backward compatibility will not work |
| #Default config is Disable |
| #Enable 0x01 |
| #Disable 0x00 |
| NXP_CN_TRANSIT_CMA_BYPASSMODE_ENABLE=0x00 |
| |
| ############################################################################### |
| #NXP_CN_TRANSIT_BLK_NUM_CHECK_ENABLE |
| #Enable/Disable block number checks for china transit use case |
| #Enable 0x01 |
| #Disable 0x00 |
| NXP_CN_TRANSIT_BLK_NUM_CHECK_ENABLE=0x01 |
| |
| ############################################################################### |
| #Enable NXP NCI runtime parser library |
| #Enable 0x01 |
| #Disable 0x00 |
| NXP_NCI_PARSER_LIBRARY=0x00 |
| |
| ############################################################################### |
| #This config will enable different level of Rf transaction debugs based on the |
| #following values provided. Decoded information will be printed in adb logcat |
| #Debug Mode Levels |
| #Disable Debug 0x00 |
| #L1 Debug 0x01 |
| #L2 Debug 0x02 |
| #L1 & L2 Debug 0x03 |
| #L1 & L2 & RSSI 0x04 |
| #L1 & L2 & Felica 0x05 |
| #NXP_CORE_PROP_SYSTEM_DEBUG=0x00 |
| |
| ############################################################################### |
| # Wired mode resume timeout vaule in wired mode resume feature enable |
| # DWP resume time out in ms( 4 bytes hex value and LSB first) |
| #example 1000 = 0x03E8 |
| #exmaple 2000 = 0x07D0 |
| #example 500 = 0x01F4 |
| NXP_WIREDMODE_RESUME_TIMEOUT={E8,03,00,00} |
| |
| ############################################################################### |
| # Power to eSE is controlled by DH or PMU depending on following configurations |
| #define DH_PWR_CONTROL 1 |
| #define PMU_PWR_CONTROL 2 |
| NXP_ESE_POWER_DH_CONTROL=1 |
| |
| ############################################################################### |
| # Timeout value in milliseconds for wired mode resume after RF field event timeout |
| NXP_NFCC_RF_FIELD_EVENT_TIMEOUT=3000 |
| |
| ############################################################################### |
| # NXP PMU Support configuration is sent if PMU_PWR_CONTROL is configured |
| # External PMU available in phone ON and phone OFF case if NXP_ESE_POWER_EXT_PMU=1 |
| # External PMU available only in phone ON case if NXP_ESE_POWER_EXT_PMU=2 |
| NXP_ESE_POWER_EXT_PMU=2 |
| |
| ############################################################################### |
| # Whether to allow wired mode in desfire and mifare CLT |
| # Disable 0x00 |
| # Enable 0x01 |
| NXP_ALLOW_WIRED_IN_MIFARE_DESFIRE_CLT=0x00 |
| |
| ############################################################################### |
| # Enable/Disable Block Route feature. |
| # Block Route will restrict routing to first matched rule |
| # Block Route enable 0x01 |
| # Block Route disable 0x00 |
| AID_BLOCK_ROUTE=0x00 |
| |
| ############################################################################### |
| # Send DWP interface reset command as part of SE open |
| # Disable 0x00 |
| # Enable 0x01 |
| NXP_DWP_INTF_RESET_ENABLE=0x00 |
| |
| ############################################################################### |
| # Timeout value in milliseconds for JCOP OS download to complete |
| OS_DOWNLOAD_TIMEOUT_VALUE=60000 |
| |
| ############################################################################### |
| # Timeout value in milliseconds to send response for Felica command received |
| NXP_HCEF_CMD_RSP_TIMEOUT_VALUE=5000 |
| |
| ############################################################################### |
| # Maximum WTX requests entertained by MW |
| NXP_WM_MAX_WTX_COUNT=50 |
| |
| ############################################################################### |
| # HAL library path for selftest |
| NXP_HAL_PATH="/vendor/lib64/hw/nfc_nci.pn54x.so" |
| |
| ############################################################################### |
| # Enable or Disable RF_STATUS_UPDATE to EseHal module |
| # Disable 0x00 |
| # Enable 0x01 |
| RF_STATUS_UPDATE_ENABLE=0x01 |
| |
| ############################################################################### |
| # Vendor Specific Proprietary Protocol & Discovery Configuration |
| # Set to 0xFF if unsupported |
| # byte[0] NCI_PROTOCOL_18092_ACTIVE |
| # byte[1] NCI_PROTOCOL_B_PRIME |
| # byte[2] NCI_PROTOCOL_DUAL |
| # byte[3] NCI_PROTOCOL_15693 |
| # byte[4] NCI_PROTOCOL_KOVIO |
| # byte[5] NCI_PROTOCOL_MIFARE |
| # byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO |
| # byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME |
| # byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME |
| NFA_PROPRIETARY_CFG={05, FF, FF, 06, 81, 80, 70, FF, FF} |
| |
| ############################################################################### |
| #White list of Hosts |
| #This values will be the Hosts(NFCEEs) in the HCI Network. |
| DEVICE_HOST_WHITE_LIST={C0, 02} |
| |
| ############################################################################### |
| # Choose the presence-check algorithm for type-4 tag. If not defined, the default value is 1. |
| # 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm |
| # 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block |
| # 2 NFA_RW_PRES_CHK_ISO_DEP_NAK; Type - 4 tag protocol iso-dep nak presence check |
| PRESENCE_CHECK_ALGORITHM=2 |
| |
| ############################################################################### |
| # Extended APDU length for ISO_DEP |
| ISO_DEP_MAX_TRANSCEIVE=0xFEFF |
| |
| ############################################################################### |
| #OffHost ESE route location for MultiSE |
| #ESE = 01 |
| OFFHOST_ROUTE_ESE={01} |
| |
| ############################################################################### |
| #OffHost UICC route location for MultiSE |
| #UICC1 = 02 |
| #UICC2 = 03 |
| OFFHOST_ROUTE_UICC={02} |
| |
| ############################################################################### |
| #CORE_SET_CONF_CMD to reset Prop Emvco Flag |
| NXP_PROP_RESET_EMVCO_CMD={20, 02, 05, 01, A0, 44, 01, 00} |
| |
| ############################################################################### |
| # Disable Mifare CLT for JCOP4.1 |
| # Enable 0x01 |
| # Disable 0x00 |
| NXP_MF_CLT_JCOP_CFG=0x00 |
| |
| ############################################################################### |
| # NFCC POLLING CONFIGURATION |
| # 0 -> NFC Default |
| # 1 -> EMVCO Default |
| # 3 -> EMVCO Polling, DISC_IDLE = POWER_OFF, DISC DEACTIVATE = Removal process |
| # 5 -> EMVCO Cert Polling, DISC_IDLE = Removal process , DISC DEACTIVATE = POWER_OFF |
| # 7 -> EMVCO Polling, DISC_IDLE = POWER_OFF, DISC DEACTIVATE = POWER_OFF |
| NFA_CONFIG_FORMAT=1 |
| |
| ############################################################################### |