| /* Copyright (c) 2012-2019, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| |
| #ifndef _APR_AUDIO_V2_H_ |
| #define _APR_AUDIO_V2_H_ |
| |
| #include <ipc/apr.h> |
| #include <linux/msm_audio.h> |
| |
| /* size of header needed for passing data out of band */ |
| #define APR_CMD_OB_HDR_SZ 12 |
| |
| /* size of header needed for getting data */ |
| #define APR_CMD_GET_HDR_SZ 16 |
| |
| struct param_outband { |
| size_t size; |
| void *kvaddr; |
| phys_addr_t paddr; |
| }; |
| |
| #define ADSP_ADM_VERSION 0x00070000 |
| |
| #define ADM_CMD_SHARED_MEM_MAP_REGIONS 0x00010322 |
| #define ADM_CMDRSP_SHARED_MEM_MAP_REGIONS 0x00010323 |
| #define ADM_CMD_SHARED_MEM_UNMAP_REGIONS 0x00010324 |
| |
| #define ADM_CMD_MATRIX_MAP_ROUTINGS_V5 0x00010325 |
| #define ADM_CMD_STREAM_DEVICE_MAP_ROUTINGS_V5 0x0001033D |
| /* Enumeration for an audio Rx matrix ID.*/ |
| #define ADM_MATRIX_ID_AUDIO_RX 0 |
| |
| #define ADM_MATRIX_ID_AUDIO_TX 1 |
| |
| #define ADM_MATRIX_ID_COMPRESSED_AUDIO_RX 2 |
| |
| #define ADM_MATRIX_ID_COMPRESSED_AUDIO_TX 3 |
| |
| #define ADM_MATRIX_ID_LISTEN_TX 4 |
| /* Enumeration for an audio Tx matrix ID.*/ |
| #define ADM_MATRIX_ID_AUDIOX 1 |
| |
| #define ADM_MAX_COPPS 5 |
| |
| /* make sure this matches with msm_audio_calibration */ |
| #define SP_V2_NUM_MAX_SPKR 2 |
| |
| /* Session map node structure. |
| * Immediately following this structure are num_copps |
| * entries of COPP IDs. The COPP IDs are 16 bits, so |
| * there might be a padding 16-bit field if num_copps |
| * is odd. |
| */ |
| struct adm_session_map_node_v5 { |
| u16 session_id; |
| /* Handle of the ASM session to be routed. Supported values: 1 |
| * to 8. |
| */ |
| |
| |
| u16 num_copps; |
| /* Number of COPPs to which this session is to be routed. |
| * Supported values: 0 < num_copps <= ADM_MAX_COPPS. |
| */ |
| } __packed; |
| |
| /* Payload of the #ADM_CMD_MATRIX_MAP_ROUTINGS_V5 command. |
| * Immediately following this structure are num_sessions of the session map |
| * node payload (adm_session_map_node_v5). |
| */ |
| |
| struct adm_cmd_matrix_map_routings_v5 { |
| struct apr_hdr hdr; |
| |
| u32 matrix_id; |
| /* Specifies whether the matrix ID is Audio Rx (0) or Audio Tx |
| * (1). Use the ADM_MATRIX_ID_AUDIO_RX or ADM_MATRIX_ID_AUDIOX |
| * macros to set this field. |
| */ |
| u32 num_sessions; |
| /* Number of sessions being updated by this command (optional). */ |
| } __packed; |
| |
| /* This command allows a client to open a COPP/Voice Proc. TX module |
| * and sets up the device session: Matrix -> COPP -> AFE on the RX |
| * and AFE -> COPP -> Matrix on the TX. This enables PCM data to |
| * be transferred to/from the endpoint (AFEPortID). |
| * |
| * @return |
| * #ADM_CMDRSP_DEVICE_OPEN_V5 with the resulting status and COPP ID. |
| */ |
| #define ADM_CMD_DEVICE_OPEN_V5 0x00010326 |
| |
| /* This command allows a client to open a COPP/Voice Proc the |
| * way as ADM_CMD_DEVICE_OPEN_V5 but supports multiple endpoint2 |
| * channels. |
| * |
| * @return |
| * #ADM_CMDRSP_DEVICE_OPEN_V6 with the resulting status and |
| * COPP ID. |
| */ |
| #define ADM_CMD_DEVICE_OPEN_V6 0x00010356 |
| |
| /* Definition for a low latency stream session. */ |
| #define ADM_LOW_LATENCY_DEVICE_SESSION 0x2000 |
| |
| /* Definition for a ultra low latency stream session. */ |
| #define ADM_ULTRA_LOW_LATENCY_DEVICE_SESSION 0x4000 |
| |
| /* Definition for a ultra low latency with Post Processing stream session. */ |
| #define ADM_ULL_POST_PROCESSING_DEVICE_SESSION 0x8000 |
| |
| /* Definition for a legacy device session. */ |
| #define ADM_LEGACY_DEVICE_SESSION 0 |
| |
| /* Indicates that endpoint_id_2 is to be ignored.*/ |
| #define ADM_CMD_COPP_OPEN_END_POINT_ID_2_IGNORE 0xFFFF |
| |
| #define ADM_CMD_COPP_OPEN_MODE_OF_OPERATION_RX_PATH_COPP 1 |
| |
| #define ADM_CMD_COPP_OPEN_MODE_OF_OPERATIONX_PATH_LIVE_COPP 2 |
| |
| #define ADM_CMD_COPP_OPEN_MODE_OF_OPERATIONX_PATH_NON_LIVE_COPP 3 |
| |
| /* Indicates that an audio COPP is to send/receive a mono PCM |
| * stream to/from |
| * END_POINT_ID_1. |
| */ |
| #define ADM_CMD_COPP_OPEN_CHANNEL_CONFIG_MONO 1 |
| |
| /* Indicates that an audio COPP is to send/receive a |
| * stereo PCM stream to/from END_POINT_ID_1. |
| */ |
| #define ADM_CMD_COPP_OPEN_CHANNEL_CONFIG_STEREO 2 |
| |
| /* Sample rate is 8000 Hz.*/ |
| #define ADM_CMD_COPP_OPEN_SAMPLE_RATE_8K 8000 |
| |
| /* Sample rate is 16000 Hz.*/ |
| #define ADM_CMD_COPP_OPEN_SAMPLE_RATE_16K 16000 |
| |
| /* Sample rate is 48000 Hz.*/ |
| #define ADM_CMD_COPP_OPEN_SAMPLE_RATE_48K 48000 |
| |
| /* Definition for a COPP live input flag bitmask.*/ |
| #define ADM_BIT_MASK_COPP_LIVE_INPUT_FLAG (0x0001U) |
| |
| /* Definition for a COPP live shift value bitmask.*/ |
| #define ADM_SHIFT_COPP_LIVE_INPUT_FLAG 0 |
| |
| /* Definition for the COPP ID bitmask.*/ |
| #define ADM_BIT_MASK_COPP_ID (0x0000FFFFUL) |
| |
| /* Definition for the COPP ID shift value.*/ |
| #define ADM_SHIFT_COPP_ID 0 |
| |
| /* Definition for the service ID bitmask.*/ |
| #define ADM_BIT_MASK_SERVICE_ID (0x00FF0000UL) |
| |
| /* Definition for the service ID shift value.*/ |
| #define ADM_SHIFT_SERVICE_ID 16 |
| |
| /* Definition for the domain ID bitmask.*/ |
| #define ADM_BIT_MASK_DOMAIN_ID (0xFF000000UL) |
| |
| /* Definition for the domain ID shift value.*/ |
| #define ADM_SHIFT_DOMAIN_ID 24 |
| |
| /* ADM device open command payload of the |
| * #ADM_CMD_DEVICE_OPEN_V5 command. |
| */ |
| struct adm_cmd_device_open_v5 { |
| struct apr_hdr hdr; |
| u16 flags; |
| /* Reserved for future use. Clients must set this field |
| * to zero. |
| */ |
| |
| u16 mode_of_operation; |
| /* Specifies whether the COPP must be opened on the Tx or Rx |
| * path. Use the ADM_CMD_COPP_OPEN_MODE_OF_OPERATION_* macros for |
| * supported values and interpretation. |
| * Supported values: |
| * - 0x1 -- Rx path COPP |
| * - 0x2 -- Tx path live COPP |
| * - 0x3 -- Tx path nonlive COPP |
| * Live connections cause sample discarding in the Tx device |
| * matrix if the destination output ports do not pull them |
| * fast enough. Nonlive connections queue the samples |
| * indefinitely. |
| */ |
| |
| u16 endpoint_id_1; |
| /* Logical and physical endpoint ID of the audio path. |
| * If the ID is a voice processor Tx block, it receives near |
| * samples. Supported values: Any pseudoport, AFE Rx port, |
| * or AFE Tx port For a list of valid IDs, refer to |
| * @xhyperref{Q4,[Q4]}. |
| * Q4 = Hexagon Multimedia: AFE Interface Specification |
| */ |
| |
| u16 endpoint_id_2; |
| /* Logical and physical endpoint ID 2 for a voice processor |
| * Tx block. |
| * This is not applicable to audio COPP. |
| * Supported values: |
| * - AFE Rx port |
| * - 0xFFFF -- Endpoint 2 is unavailable and the voice |
| * processor Tx |
| * block ignores this endpoint |
| * When the voice processor Tx block is created on the audio |
| * record path, |
| * it can receive far-end samples from an AFE Rx port if the |
| * voice call |
| * is active. The ID of the AFE port is provided in this |
| * field. |
| * For a list of valid IDs, refer @xhyperref{Q4,[Q4]}. |
| */ |
| |
| u32 topology_id; |
| /* Audio COPP topology ID; 32-bit GUID. */ |
| |
| u16 dev_num_channel; |
| /* Number of channels the audio COPP sends to/receives from |
| * the endpoint. |
| * Supported values: 1 to 8. |
| * The value is ignored for the voice processor Tx block, |
| * where channel |
| * configuration is derived from the topology ID. |
| */ |
| |
| u16 bit_width; |
| /* Bit width (in bits) that the audio COPP sends to/receives |
| * from the |
| * endpoint. The value is ignored for the voice processing |
| * Tx block, |
| * where the PCM width is 16 bits. |
| */ |
| |
| u32 sample_rate; |
| /* Sampling rate at which the audio COPP/voice processor |
| * Tx block |
| * interfaces with the endpoint. |
| * Supported values for voice processor Tx: 8000, 16000, |
| * 48000 Hz |
| * Supported values for audio COPP: >0 and <=192 kHz |
| */ |
| |
| u8 dev_channel_mapping[8]; |
| /* Array of channel mapping of buffers that the audio COPP |
| * sends to the endpoint. Channel[i] mapping describes channel |
| * I inside the buffer, where 0 < i < dev_num_channel. |
| * This value is relevant only for an audio Rx COPP. |
| * For the voice processor block and Tx audio block, this field |
| * is set to zero and is ignored. |
| */ |
| } __packed; |
| |
| /* ADM device open command payload of the |
| * #ADM_CMD_DEVICE_OPEN_V6 command. |
| */ |
| struct adm_cmd_device_open_v6 { |
| struct apr_hdr hdr; |
| u16 flags; |
| /* Reserved for future use. Clients must set this field |
| * to zero. |
| */ |
| |
| u16 mode_of_operation; |
| /* Specifies whether the COPP must be opened on the Tx or Rx |
| * path. Use the ADM_CMD_COPP_OPEN_MODE_OF_OPERATION_* macros for |
| * supported values and interpretation. |
| * Supported values: |
| * - 0x1 -- Rx path COPP |
| * - 0x2 -- Tx path live COPP |
| * - 0x3 -- Tx path nonlive COPP |
| * Live connections cause sample discarding in the Tx device |
| * matrix if the destination output ports do not pull them |
| * fast enough. Nonlive connections queue the samples |
| * indefinitely. |
| */ |
| |
| u16 endpoint_id_1; |
| /* Logical and physical endpoint ID of the audio path. |
| * If the ID is a voice processor Tx block, it receives near |
| * samples. Supported values: Any pseudoport, AFE Rx port, |
| * or AFE Tx port For a list of valid IDs, refer to |
| * @xhyperref{Q4,[Q4]}. |
| * Q4 = Hexagon Multimedia: AFE Interface Specification |
| */ |
| |
| u16 endpoint_id_2; |
| /* Logical and physical endpoint ID 2 for a voice processor |
| * Tx block. |
| * This is not applicable to audio COPP. |
| * Supported values: |
| * - AFE Rx port |
| * - 0xFFFF -- Endpoint 2 is unavailable and the voice |
| * processor Tx |
| * block ignores this endpoint |
| * When the voice processor Tx block is created on the audio |
| * record path, |
| * it can receive far-end samples from an AFE Rx port if the |
| * voice call |
| * is active. The ID of the AFE port is provided in this |
| * field. |
| * For a list of valid IDs, refer @xhyperref{Q4,[Q4]}. |
| */ |
| |
| u32 topology_id; |
| /* Audio COPP topology ID; 32-bit GUID. */ |
| |
| u16 dev_num_channel; |
| /* Number of channels the audio COPP sends to/receives from |
| * the endpoint. |
| * Supported values: 1 to 8. |
| * The value is ignored for the voice processor Tx block, |
| * where channel |
| * configuration is derived from the topology ID. |
| */ |
| |
| u16 bit_width; |
| /* Bit width (in bits) that the audio COPP sends to/receives |
| * from the |
| * endpoint. The value is ignored for the voice processing |
| * Tx block, |
| * where the PCM width is 16 bits. |
| */ |
| |
| u32 sample_rate; |
| /* Sampling rate at which the audio COPP/voice processor |
| * Tx block |
| * interfaces with the endpoint. |
| * Supported values for voice processor Tx: 8000, 16000, |
| * 48000 Hz |
| * Supported values for audio COPP: >0 and <=192 kHz |
| */ |
| |
| u8 dev_channel_mapping[8]; |
| /* Array of channel mapping of buffers that the audio COPP |
| * sends to the endpoint. Channel[i] mapping describes channel |
| * I inside the buffer, where 0 < i < dev_num_channel. |
| * This value is relevant only for an audio Rx COPP. |
| * For the voice processor block and Tx audio block, this field |
| * is set to zero and is ignored. |
| */ |
| |
| u16 dev_num_channel_eid2; |
| /* Number of channels the voice processor block sends |
| * to/receives from the endpoint2. |
| * Supported values: 1 to 8. |
| * The value is ignored for audio COPP or if endpoint_id_2 is |
| * set to 0xFFFF. |
| */ |
| |
| u16 bit_width_eid2; |
| /* Bit width (in bits) that the voice processor sends |
| * to/receives from the endpoint2. |
| * Supported values: 16 and 24. |
| * The value is ignored for audio COPP or if endpoint_id_2 is |
| * set to 0xFFFF. |
| */ |
| |
| u32 sample_rate_eid2; |
| /* Sampling rate at which the voice processor Tx block |
| * interfaces with the endpoint2. |
| * Supported values for Tx voice processor: >0 and <=384 kHz |
| * The value is ignored for audio COPP or if endpoint_id_2 is |
| * set to 0xFFFF. |
| */ |
| |
| u8 dev_channel_mapping_eid2[8]; |
| /* Array of channel mapping of buffers that the voice processor |
| * sends to the endpoint. Channel[i] mapping describes channel |
| * I inside the buffer, where 0 < i < dev_num_channel. |
| * This value is relevant only for the Tx voice processor. |
| * The values are ignored for audio COPP or if endpoint_id_2 is |
| * set to 0xFFFF. |
| */ |
| } __packed; |
| |
| /* |
| * This command allows the client to close a COPP and disconnect |
| * the device session. |
| */ |
| #define ADM_CMD_DEVICE_CLOSE_V5 0x00010327 |
| |
| /* Sets one or more parameters to a COPP. */ |
| #define ADM_CMD_SET_PP_PARAMS_V5 0x00010328 |
| |
| /* Payload of the #ADM_CMD_SET_PP_PARAMS_V5 command. |
| * If the data_payload_addr_lsw and data_payload_addr_msw element |
| * are NULL, a series of adm_param_datastructures immediately |
| * follows, whose total size is data_payload_size bytes. |
| */ |
| struct adm_cmd_set_pp_params_v5 { |
| struct apr_hdr hdr; |
| u32 payload_addr_lsw; |
| /* LSW of parameter data payload address. */ |
| u32 payload_addr_msw; |
| /* MSW of parameter data payload address. */ |
| |
| u32 mem_map_handle; |
| /* Memory map handle returned by ADM_CMD_SHARED_MEM_MAP_REGIONS |
| * command |
| * |
| * If mem_map_handle is zero implies the message is in |
| * the payload |
| */ |
| |
| u32 payload_size; |
| /* Size in bytes of the variable payload accompanying this |
| * message or |
| * in shared memory. This is used for parsing the parameter |
| * payload. |
| */ |
| } __packed; |
| |
| /* Payload format for COPP parameter data. |
| * Immediately following this structure are param_size bytes |
| * of parameter |
| * data. |
| */ |
| struct adm_param_data_v5 { |
| u32 module_id; |
| /* Unique ID of the module. */ |
| u32 param_id; |
| /* Unique ID of the parameter. */ |
| u16 param_size; |
| /* Data size of the param_id/module_id combination. |
| * This value is a |
| * multiple of 4 bytes. |
| */ |
| u16 reserved; |
| /* Reserved for future enhancements. |
| * This field must be set to zero. |
| */ |
| } __packed; |
| |
| #define ASM_STREAM_CMD_REGISTER_PP_EVENTS 0x00013213 |
| #define ASM_STREAM_PP_EVENT 0x00013214 |
| #define ASM_STREAM_CMD_REGISTER_IEC_61937_FMT_UPDATE 0x13333 |
| #define ASM_IEC_61937_MEDIA_FMT_EVENT 0x13334 |
| |
| #define DSP_STREAM_CMD "ADSP Stream Cmd" |
| #define DSP_STREAM_CALLBACK "ADSP Stream Callback Event" |
| #define DSP_STREAM_CALLBACK_QUEUE_SIZE 1024 |
| |
| struct dsp_stream_callback_list { |
| struct list_head list; |
| struct msm_adsp_event_data event; |
| }; |
| |
| struct dsp_stream_callback_prtd { |
| uint16_t event_count; |
| struct list_head event_queue; |
| spinlock_t prtd_spin_lock; |
| }; |
| |
| /* set customized mixing on matrix mixer */ |
| #define ADM_CMD_SET_PSPD_MTMX_STRTR_PARAMS_V5 0x00010344 |
| struct adm_cmd_set_pspd_mtmx_strtr_params_v5 { |
| struct apr_hdr hdr; |
| /* LSW of parameter data payload address.*/ |
| u32 payload_addr_lsw; |
| /* MSW of parameter data payload address.*/ |
| u32 payload_addr_msw; |
| /* Memory map handle returned by ADM_CMD_SHARED_MEM_MAP_REGIONS */ |
| /* command. If mem_map_handle is zero implies the message is in */ |
| /* the payload */ |
| u32 mem_map_handle; |
| /* Size in bytes of the variable payload accompanying this */ |
| /* message or in shared memory. This is used for parsing the */ |
| /* parameter payload. */ |
| u32 payload_size; |
| u16 direction; |
| u16 sessionid; |
| u16 deviceid; |
| u16 reserved; |
| } __packed; |
| |
| /* Defined specifically for in-band use, includes params */ |
| struct adm_cmd_set_pp_params_inband_v5 { |
| struct apr_hdr hdr; |
| /* LSW of parameter data payload address.*/ |
| u32 payload_addr_lsw; |
| /* MSW of parameter data payload address.*/ |
| u32 payload_addr_msw; |
| /* Memory map handle returned by ADM_CMD_SHARED_MEM_MAP_REGIONS */ |
| /* command. If mem_map_handle is zero implies the message is in */ |
| /* the payload */ |
| u32 mem_map_handle; |
| /* Size in bytes of the variable payload accompanying this */ |
| /* message or in shared memory. This is used for parsing the */ |
| /* parameter payload. */ |
| u32 payload_size; |
| /* Parameters passed for in band payload */ |
| struct adm_param_data_v5 params; |
| } __packed; |
| |
| /* Returns the status and COPP ID to an #ADM_CMD_DEVICE_OPEN_V5 command. |
| */ |
| #define ADM_CMDRSP_DEVICE_OPEN_V5 0x00010329 |
| |
| /* Payload of the #ADM_CMDRSP_DEVICE_OPEN_V5 message, |
| * which returns the |
| * status and COPP ID to an #ADM_CMD_DEVICE_OPEN_V5 command. |
| */ |
| struct adm_cmd_rsp_device_open_v5 { |
| u32 status; |
| /* Status message (error code).*/ |
| |
| u16 copp_id; |
| /* COPP ID: Supported values: 0 <= copp_id < ADM_MAX_COPPS*/ |
| |
| u16 reserved; |
| /* Reserved. This field must be set to zero.*/ |
| } __packed; |
| |
| /* Returns the status and COPP ID to an #ADM_CMD_DEVICE_OPEN_V6 command. */ |
| #define ADM_CMDRSP_DEVICE_OPEN_V6 0x00010357 |
| |
| /* Payload of the #ADM_CMDRSP_DEVICE_OPEN_V6 message, |
| * which returns the |
| * status and COPP ID to an #ADM_CMD_DEVICE_OPEN_V6 command |
| * is the exact same as ADM_CMDRSP_DEVICE_OPEN_V5. |
| */ |
| |
| /* This command allows a query of one COPP parameter. */ |
| #define ADM_CMD_GET_PP_PARAMS_V5 0x0001032A |
| |
| /* Payload an #ADM_CMD_GET_PP_PARAMS_V5 command. */ |
| struct adm_cmd_get_pp_params_v5 { |
| struct apr_hdr hdr; |
| u32 data_payload_addr_lsw; |
| /* LSW of parameter data payload address.*/ |
| |
| u32 data_payload_addr_msw; |
| /* MSW of parameter data payload address.*/ |
| |
| /* If the mem_map_handle is non zero, |
| * on ACK, the ParamData payloads begin at |
| * the address specified (out-of-band). |
| */ |
| |
| u32 mem_map_handle; |
| /* Memory map handle returned |
| * by ADM_CMD_SHARED_MEM_MAP_REGIONS command. |
| * If the mem_map_handle is 0, it implies that |
| * the ACK's payload will contain the ParamData (in-band). |
| */ |
| |
| u32 module_id; |
| /* Unique ID of the module. */ |
| |
| u32 param_id; |
| /* Unique ID of the parameter. */ |
| |
| u16 param_max_size; |
| /* Maximum data size of the parameter |
| *ID/module ID combination. This |
| * field is a multiple of 4 bytes. |
| */ |
| u16 reserved; |
| /* Reserved for future enhancements. |
| * This field must be set to zero. |
| */ |
| } __packed; |
| |
| /* Returns parameter values |
| * in response to an #ADM_CMD_GET_PP_PARAMS_V5 command. |
| */ |
| #define ADM_CMDRSP_GET_PP_PARAMS_V5 0x0001032B |
| |
| /* Payload of the #ADM_CMDRSP_GET_PP_PARAMS_V5 message, |
| * which returns parameter values in response |
| * to an #ADM_CMD_GET_PP_PARAMS_V5 command. |
| * Immediately following this |
| * structure is the adm_param_data_v5 |
| * structure containing the pre/postprocessing |
| * parameter data. For an in-band |
| * scenario, the variable payload depends |
| * on the size of the parameter. |
| */ |
| struct adm_cmd_rsp_get_pp_params_v5 { |
| u32 status; |
| /* Status message (error code).*/ |
| } __packed; |
| |
| /* Structure for holding soft stepping volume parameters. */ |
| |
| /* |
| * Payload of the #ASM_PARAM_ID_SOFT_VOL_STEPPING_PARAMETERS |
| * parameters used by the Volume Control module. |
| */ |
| |
| struct audproc_softvolume_params { |
| u32 period; |
| u32 step; |
| u32 rampingcurve; |
| } __packed; |
| |
| /* |
| * ID of the Media Format Converter (MFC) module. |
| * This module supports the following parameter IDs: |
| * #AUDPROC_PARAM_ID_MFC_OUTPUT_MEDIA_FORMAT |
| * #AUDPROC_CHMIXER_PARAM_ID_COEFF |
| */ |
| #define AUDPROC_MODULE_ID_MFC 0x00010912 |
| |
| /* ID of the Output Media Format parameters used by AUDPROC_MODULE_ID_MFC. |
| * |
| */ |
| #define AUDPROC_PARAM_ID_MFC_OUTPUT_MEDIA_FORMAT 0x00010913 |
| |
| /* Param ID of Channel Mixer used by AUDPROC_MODULE_ID_MFC */ |
| #define AUDPROC_CHMIXER_PARAM_ID_COEFF 0x00010342 |
| |
| |
| struct audproc_mfc_output_media_fmt { |
| struct adm_cmd_set_pp_params_v5 params; |
| struct adm_param_data_v5 data; |
| uint32_t sampling_rate; |
| uint16_t bits_per_sample; |
| uint16_t num_channels; |
| uint16_t channel_type[8]; |
| } __packed; |
| |
| struct audproc_volume_ctrl_master_gain { |
| struct adm_cmd_set_pp_params_v5 params; |
| struct adm_param_data_v5 data; |
| /* Linear gain in Q13 format. */ |
| uint16_t master_gain; |
| /* Clients must set this field to zero. */ |
| uint16_t reserved; |
| } __packed; |
| |
| struct audproc_soft_step_volume_params { |
| struct adm_cmd_set_pp_params_v5 params; |
| struct adm_param_data_v5 data; |
| /* |
| * Period in milliseconds. |
| * Supported values: 0 to 15000 |
| */ |
| uint32_t period; |
| /* |
| * Step in microseconds. |
| * Supported values: 0 to 15000000 |
| */ |
| uint32_t step; |
| /* |
| * Ramping curve type. |
| * Supported values: |
| * - #AUDPROC_PARAM_SVC_RAMPINGCURVE_LINEAR |
| * - #AUDPROC_PARAM_SVC_RAMPINGCURVE_EXP |
| * - #AUDPROC_PARAM_SVC_RAMPINGCURVE_LOG |
| */ |
| uint32_t ramping_curve; |
| } __packed; |
| |
| struct audproc_enable_param_t { |
| struct adm_cmd_set_pp_params_inband_v5 pp_params; |
| /* |
| * Specifies whether the Audio processing module is enabled. |
| * This parameter is generic/common parameter to configure or |
| * determine the state of any audio processing module. |
| |
| * @values 0 : Disable 1: Enable |
| */ |
| uint32_t enable; |
| }; |
| |
| /* |
| * Allows a client to control the gains on various session-to-COPP paths. |
| */ |
| #define ADM_CMD_MATRIX_RAMP_GAINS_V5 0x0001032C |
| |
| /* Indicates that the target gain in the |
| * current adm_session_copp_gain_v5 |
| * structure is to be applied to all |
| * the session-to-COPP paths that exist for |
| * the specified session. |
| */ |
| #define ADM_CMD_MATRIX_RAMP_GAINS_COPP_ID_ALL_CONNECTED_COPPS 0xFFFF |
| |
| /* Indicates that the target gain is |
| * to be immediately applied to the |
| * specified session-to-COPP path, |
| * without a ramping fashion. |
| */ |
| #define ADM_CMD_MATRIX_RAMP_GAINS_RAMP_DURATION_IMMEDIATE 0x0000 |
| |
| /* Enumeration for a linear ramping curve.*/ |
| #define ADM_CMD_MATRIX_RAMP_GAINS_RAMP_CURVE_LINEAR 0x0000 |
| |
| /* Payload of the #ADM_CMD_MATRIX_RAMP_GAINS_V5 command. |
| * Immediately following this structure are num_gains of the |
| * adm_session_copp_gain_v5structure. |
| */ |
| struct adm_cmd_matrix_ramp_gains_v5 { |
| u32 matrix_id; |
| /* Specifies whether the matrix ID is Audio Rx (0) or Audio Tx (1). |
| * Use the ADM_MATRIX_ID_AUDIO_RX or ADM_MATRIX_ID_AUDIOX |
| * macros to set this field. |
| */ |
| |
| u16 num_gains; |
| /* Number of gains being applied. */ |
| |
| u16 reserved_for_align; |
| /* Reserved. This field must be set to zero.*/ |
| } __packed; |
| |
| /* Session-to-COPP path gain structure, used by the |
| * #ADM_CMD_MATRIX_RAMP_GAINS_V5 command. |
| * This structure specifies the target |
| * gain (per channel) that must be applied |
| * to a particular session-to-COPP path in |
| * the audio matrix. The structure can |
| * also be used to apply the gain globally |
| * to all session-to-COPP paths that |
| * exist for the given session. |
| * The aDSP uses device channel mapping to |
| * determine which channel gains to |
| * use from this command. For example, |
| * if the device is configured as stereo, |
| * the aDSP uses only target_gain_ch_1 and |
| * target_gain_ch_2, and it ignores |
| * the others. |
| */ |
| struct adm_session_copp_gain_v5 { |
| u16 session_id; |
| /* Handle of the ASM session. |
| * Supported values: 1 to 8. |
| */ |
| |
| u16 copp_id; |
| /* Handle of the COPP. Gain will be applied on the Session ID |
| * COPP ID path. |
| */ |
| |
| u16 ramp_duration; |
| /* Duration (in milliseconds) of the ramp over |
| * which target gains are |
| * to be applied. Use |
| * #ADM_CMD_MATRIX_RAMP_GAINS_RAMP_DURATION_IMMEDIATE |
| * to indicate that gain must be applied immediately. |
| */ |
| |
| u16 step_duration; |
| /* Duration (in milliseconds) of each step in the ramp. |
| * This parameter is ignored if ramp_duration is equal to |
| * #ADM_CMD_MATRIX_RAMP_GAINS_RAMP_DURATION_IMMEDIATE. |
| * Supported value: 1 |
| */ |
| |
| u16 ramp_curve; |
| /* Type of ramping curve. |
| * Supported value: #ADM_CMD_MATRIX_RAMP_GAINS_RAMP_CURVE_LINEAR |
| */ |
| |
| u16 reserved_for_align; |
| /* Reserved. This field must be set to zero. */ |
| |
| u16 target_gain_ch_1; |
| /* Target linear gain for channel 1 in Q13 format; */ |
| |
| u16 target_gain_ch_2; |
| /* Target linear gain for channel 2 in Q13 format; */ |
| |
| u16 target_gain_ch_3; |
| /* Target linear gain for channel 3 in Q13 format; */ |
| |
| u16 target_gain_ch_4; |
| /* Target linear gain for channel 4 in Q13 format; */ |
| |
| u16 target_gain_ch_5; |
| /* Target linear gain for channel 5 in Q13 format; */ |
| |
| u16 target_gain_ch_6; |
| /* Target linear gain for channel 6 in Q13 format; */ |
| |
| u16 target_gain_ch_7; |
| /* Target linear gain for channel 7 in Q13 format; */ |
| |
| u16 target_gain_ch_8; |
| /* Target linear gain for channel 8 in Q13 format; */ |
| } __packed; |
| |
| /* Allows to set mute/unmute on various session-to-COPP paths. |
| * For every session-to-COPP path (stream-device interconnection), |
| * mute/unmute can be set individually on the output channels. |
| */ |
| #define ADM_CMD_MATRIX_MUTE_V5 0x0001032D |
| |
| /* Indicates that mute/unmute in the |
| * current adm_session_copp_mute_v5structure |
| * is to be applied to all the session-to-COPP |
| * paths that exist for the specified session. |
| */ |
| #define ADM_CMD_MATRIX_MUTE_COPP_ID_ALL_CONNECTED_COPPS 0xFFFF |
| |
| /* Payload of the #ADM_CMD_MATRIX_MUTE_V5 command*/ |
| struct adm_cmd_matrix_mute_v5 { |
| u32 matrix_id; |
| /* Specifies whether the matrix ID is Audio Rx (0) or Audio Tx (1). |
| * Use the ADM_MATRIX_ID_AUDIO_RX or ADM_MATRIX_ID_AUDIOX |
| * macros to set this field. |
| */ |
| |
| u16 session_id; |
| /* Handle of the ASM session. |
| * Supported values: 1 to 8. |
| */ |
| |
| u16 copp_id; |
| /* Handle of the COPP. |
| * Use ADM_CMD_MATRIX_MUTE_COPP_ID_ALL_CONNECTED_COPPS |
| * to indicate that mute/unmute must be applied to |
| * all the COPPs connected to session_id. |
| * Supported values: |
| * - 0xFFFF -- Apply mute/unmute to all connected COPPs |
| * - Other values -- Valid COPP ID |
| */ |
| |
| u8 mute_flag_ch_1; |
| /* Mute flag for channel 1 is set to unmute (0) or mute (1). */ |
| |
| u8 mute_flag_ch_2; |
| /* Mute flag for channel 2 is set to unmute (0) or mute (1). */ |
| |
| u8 mute_flag_ch_3; |
| /* Mute flag for channel 3 is set to unmute (0) or mute (1). */ |
| |
| u8 mute_flag_ch_4; |
| /* Mute flag for channel 4 is set to unmute (0) or mute (1). */ |
| |
| u8 mute_flag_ch_5; |
| /* Mute flag for channel 5 is set to unmute (0) or mute (1). */ |
| |
| u8 mute_flag_ch_6; |
| /* Mute flag for channel 6 is set to unmute (0) or mute (1). */ |
| |
| u8 mute_flag_ch_7; |
| /* Mute flag for channel 7 is set to unmute (0) or mute (1). */ |
| |
| u8 mute_flag_ch_8; |
| /* Mute flag for channel 8 is set to unmute (0) or mute (1). */ |
| |
| u16 ramp_duration; |
| /* Period (in milliseconds) over which the soft mute/unmute will be |
| * applied. |
| * Supported values: 0 (Default) to 0xFFFF |
| * The default of 0 means mute/unmute will be applied immediately. |
| */ |
| |
| u16 reserved_for_align; |
| /* Clients must set this field to zero.*/ |
| } __packed; |
| |
| #define ASM_PARAM_ID_AAC_STEREO_MIX_COEFF_SELECTION_FLAG_V2 (0x00010DD8) |
| |
| struct asm_aac_stereo_mix_coeff_selection_param_v2 { |
| struct apr_hdr hdr; |
| u32 param_id; |
| u32 param_size; |
| u32 aac_stereo_mix_coeff_flag; |
| } __packed; |
| |
| /* Allows a client to connect the desired stream to |
| * the desired AFE port through the stream router |
| * |
| * This command allows the client to connect specified session to |
| * specified AFE port. This is used for compressed streams only |
| * opened using the #ASM_STREAM_CMD_OPEN_WRITE_COMPRESSED or |
| * #ASM_STREAM_CMD_OPEN_READ_COMPRESSED command. |
| * |
| * @prerequisites |
| * Session ID and AFE Port ID must be valid. |
| * #ASM_STREAM_CMD_OPEN_WRITE_COMPRESSED or |
| * #ASM_STREAM_CMD_OPEN_READ_COMPRESSED |
| * must have been called on this session. |
| */ |
| |
| #define ADM_CMD_CONNECT_AFE_PORT_V5 0x0001032E |
| #define ADM_CMD_DISCONNECT_AFE_PORT_V5 0x0001032F |
| /* Enumeration for the Rx stream router ID.*/ |
| #define ADM_STRTR_ID_RX 0 |
| /* Enumeration for the Tx stream router ID.*/ |
| #define ADM_STRTR_IDX 1 |
| |
| /* Payload of the #ADM_CMD_CONNECT_AFE_PORT_V5 command.*/ |
| struct adm_cmd_connect_afe_port_v5 { |
| struct apr_hdr hdr; |
| u8 mode; |
| /* ID of the stream router (RX/TX). Use the |
| * ADM_STRTR_ID_RX or ADM_STRTR_IDX macros |
| * to set this field. |
| */ |
| |
| u8 session_id; |
| /* Session ID of the stream to connect */ |
| |
| u16 afe_port_id; |
| /* Port ID of the AFE port to connect to.*/ |
| u32 num_channels; |
| /* Number of device channels |
| * Supported values: 2(Audio Sample Packet), |
| * 8 (HBR Audio Stream Sample Packet) |
| */ |
| |
| u32 sampling_rate; |
| /* Device sampling rate |
| * Supported values: Any |
| */ |
| } __packed; |
| |
| |
| /* adsp_adm_api.h */ |
| |
| |
| /* Port ID. Update afe_get_port_index |
| * when a new port is added here. |
| */ |
| #define PRIMARY_I2S_RX 0 |
| #define PRIMARY_I2S_TX 1 |
| #define SECONDARY_I2S_RX 4 |
| #define SECONDARY_I2S_TX 5 |
| #define MI2S_RX 6 |
| #define MI2S_TX 7 |
| #define HDMI_RX 8 |
| #define RSVD_2 9 |
| #define RSVD_3 10 |
| #define DIGI_MIC_TX 11 |
| #define VOICE2_PLAYBACK_TX 0x8002 |
| #define VOICE_RECORD_RX 0x8003 |
| #define VOICE_RECORD_TX 0x8004 |
| #define VOICE_PLAYBACK_TX 0x8005 |
| |
| /* Slimbus Multi channel port id pool */ |
| #define SLIMBUS_0_RX 0x4000 |
| #define SLIMBUS_0_TX 0x4001 |
| #define SLIMBUS_1_RX 0x4002 |
| #define SLIMBUS_1_TX 0x4003 |
| #define SLIMBUS_2_RX 0x4004 |
| #define SLIMBUS_2_TX 0x4005 |
| #define SLIMBUS_3_RX 0x4006 |
| #define SLIMBUS_3_TX 0x4007 |
| #define SLIMBUS_4_RX 0x4008 |
| #define SLIMBUS_4_TX 0x4009 |
| #define SLIMBUS_5_RX 0x400a |
| #define SLIMBUS_5_TX 0x400b |
| #define SLIMBUS_6_RX 0x400c |
| #define SLIMBUS_6_TX 0x400d |
| #define SLIMBUS_7_RX 0x400e |
| #define SLIMBUS_7_TX 0x400f |
| #define SLIMBUS_8_RX 0x4010 |
| #define SLIMBUS_8_TX 0x4011 |
| #define SLIMBUS_PORT_LAST SLIMBUS_8_TX |
| #define INT_BT_SCO_RX 0x3000 |
| #define INT_BT_SCO_TX 0x3001 |
| #define INT_BT_A2DP_RX 0x3002 |
| #define INT_FM_RX 0x3004 |
| #define INT_FM_TX 0x3005 |
| #define RT_PROXY_PORT_001_RX 0x2000 |
| #define RT_PROXY_PORT_001_TX 0x2001 |
| #define AFE_LOOPBACK_TX 0x6001 |
| #define DISPLAY_PORT_RX 0x6020 |
| |
| #define AFE_PORT_INVALID 0xFFFF |
| #define SLIMBUS_INVALID AFE_PORT_INVALID |
| |
| #define AFE_PORT_CMD_START 0x000100ca |
| |
| #define AFE_EVENT_RTPORT_START 0 |
| #define AFE_EVENT_RTPORT_STOP 1 |
| #define AFE_EVENT_RTPORT_LOW_WM 2 |
| #define AFE_EVENT_RTPORT_HI_WM 3 |
| |
| #define ADSP_AFE_VERSION 0x00200000 |
| |
| /* Size of the range of port IDs for the audio interface. */ |
| #define AFE_PORT_ID_AUDIO_IF_PORT_RANGE_SIZE 0xF |
| |
| /* Size of the range of port IDs for internal BT-FM ports. */ |
| #define AFE_PORT_ID_INTERNAL_BT_FM_RANGE_SIZE 0x6 |
| |
| /* Size of the range of port IDs for SLIMbus<sup>® |
| * </sup> multichannel |
| * ports. |
| */ |
| #define AFE_PORT_ID_SLIMBUS_RANGE_SIZE 0xA |
| |
| /* Size of the range of port IDs for real-time proxy ports. */ |
| #define AFE_PORT_ID_RT_PROXY_PORT_RANGE_SIZE 0x2 |
| |
| /* Size of the range of port IDs for pseudoports. */ |
| #define AFE_PORT_ID_PSEUDOPORT_RANGE_SIZE 0x5 |
| |
| /* Start of the range of port IDs for the audio interface. */ |
| #define AFE_PORT_ID_AUDIO_IF_PORT_RANGE_START 0x1000 |
| |
| /* End of the range of port IDs for the audio interface. */ |
| #define AFE_PORT_ID_AUDIO_IF_PORT_RANGE_END \ |
| (AFE_PORT_ID_AUDIO_IF_PORT_RANGE_START +\ |
| AFE_PORT_ID_AUDIO_IF_PORT_RANGE_SIZE - 1) |
| |
| /* Start of the range of port IDs for real-time proxy ports. */ |
| #define AFE_PORT_ID_RT_PROXY_PORT_RANGE_START 0x2000 |
| |
| /* End of the range of port IDs for real-time proxy ports. */ |
| #define AFE_PORT_ID_RT_PROXY_PORT_RANGE_END \ |
| (AFE_PORT_ID_RT_PROXY_PORT_RANGE_START +\ |
| AFE_PORT_ID_RT_PROXY_PORT_RANGE_SIZE-1) |
| |
| /* Start of the range of port IDs for internal BT-FM devices. */ |
| #define AFE_PORT_ID_INTERNAL_BT_FM_RANGE_START 0x3000 |
| |
| /* End of the range of port IDs for internal BT-FM devices. */ |
| #define AFE_PORT_ID_INTERNAL_BT_FM_RANGE_END \ |
| (AFE_PORT_ID_INTERNAL_BT_FM_RANGE_START +\ |
| AFE_PORT_ID_INTERNAL_BT_FM_RANGE_SIZE-1) |
| |
| /* Start of the range of port IDs for SLIMbus devices. */ |
| #define AFE_PORT_ID_SLIMBUS_RANGE_START 0x4000 |
| |
| /* End of the range of port IDs for SLIMbus devices. */ |
| #define AFE_PORT_ID_SLIMBUS_RANGE_END \ |
| (AFE_PORT_ID_SLIMBUS_RANGE_START +\ |
| AFE_PORT_ID_SLIMBUS_RANGE_SIZE-1) |
| |
| /* Start of the range of port IDs for pseudoports. */ |
| #define AFE_PORT_ID_PSEUDOPORT_RANGE_START 0x8001 |
| |
| /* End of the range of port IDs for pseudoports. */ |
| #define AFE_PORT_ID_PSEUDOPORT_RANGE_END \ |
| (AFE_PORT_ID_PSEUDOPORT_RANGE_START +\ |
| AFE_PORT_ID_PSEUDOPORT_RANGE_SIZE-1) |
| |
| /* Start of the range of port IDs for TDM devices. */ |
| #define AFE_PORT_ID_TDM_PORT_RANGE_START 0x9000 |
| |
| /* End of the range of port IDs for TDM devices. */ |
| #define AFE_PORT_ID_TDM_PORT_RANGE_END \ |
| (AFE_PORT_ID_TDM_PORT_RANGE_START+0x50-1) |
| |
| /* Size of the range of port IDs for TDM ports. */ |
| #define AFE_PORT_ID_TDM_PORT_RANGE_SIZE \ |
| (AFE_PORT_ID_TDM_PORT_RANGE_END - \ |
| AFE_PORT_ID_TDM_PORT_RANGE_START+1) |
| |
| #define AFE_PORT_ID_PRIMARY_MI2S_RX 0x1000 |
| #define AFE_PORT_ID_PRIMARY_MI2S_TX 0x1001 |
| #define AFE_PORT_ID_SECONDARY_MI2S_RX 0x1002 |
| #define AFE_PORT_ID_SECONDARY_MI2S_TX 0x1003 |
| #define AFE_PORT_ID_TERTIARY_MI2S_RX 0x1004 |
| #define AFE_PORT_ID_TERTIARY_MI2S_TX 0x1005 |
| #define AFE_PORT_ID_QUATERNARY_MI2S_RX 0x1006 |
| #define AFE_PORT_ID_QUATERNARY_MI2S_TX 0x1007 |
| #define AUDIO_PORT_ID_I2S_RX 0x1008 |
| #define AFE_PORT_ID_DIGITAL_MIC_TX 0x1009 |
| #define AFE_PORT_ID_PRIMARY_PCM_RX 0x100A |
| #define AFE_PORT_ID_PRIMARY_PCM_TX 0x100B |
| #define AFE_PORT_ID_SECONDARY_PCM_RX 0x100C |
| #define AFE_PORT_ID_SECONDARY_PCM_TX 0x100D |
| #define AFE_PORT_ID_MULTICHAN_HDMI_RX 0x100E |
| #define AFE_PORT_ID_SECONDARY_MI2S_RX_SD1 0x1010 |
| #define AFE_PORT_ID_TERTIARY_PCM_RX 0x1012 |
| #define AFE_PORT_ID_TERTIARY_PCM_TX 0x1013 |
| #define AFE_PORT_ID_QUATERNARY_PCM_RX 0x1014 |
| #define AFE_PORT_ID_QUATERNARY_PCM_TX 0x1015 |
| #define AFE_PORT_ID_QUINARY_MI2S_RX 0x1016 |
| #define AFE_PORT_ID_QUINARY_MI2S_TX 0x1017 |
| /* ID of the senary MI2S Rx port. */ |
| #define AFE_PORT_ID_SENARY_MI2S_RX 0x1018 |
| /* ID of the senary MI2S Tx port. */ |
| #define AFE_PORT_ID_SENARY_MI2S_TX 0x1019 |
| |
| /* ID of the Internal 0 MI2S Rx port */ |
| #define AFE_PORT_ID_INT0_MI2S_RX 0x102E |
| /* ID of the Internal 0 MI2S Tx port */ |
| #define AFE_PORT_ID_INT0_MI2S_TX 0x102F |
| /* ID of the Internal 1 MI2S Rx port */ |
| #define AFE_PORT_ID_INT1_MI2S_RX 0x1030 |
| /* ID of the Internal 1 MI2S Tx port */ |
| #define AFE_PORT_ID_INT1_MI2S_TX 0x1031 |
| /* ID of the Internal 2 MI2S Rx port */ |
| #define AFE_PORT_ID_INT2_MI2S_RX 0x1032 |
| /* ID of the Internal 2 MI2S Tx port */ |
| #define AFE_PORT_ID_INT2_MI2S_TX 0x1033 |
| /* ID of the Internal 3 MI2S Rx port */ |
| #define AFE_PORT_ID_INT3_MI2S_RX 0x1034 |
| /* ID of the Internal 3 MI2S Tx port */ |
| #define AFE_PORT_ID_INT3_MI2S_TX 0x1035 |
| /* ID of the Internal 4 MI2S Rx port */ |
| #define AFE_PORT_ID_INT4_MI2S_RX 0x1036 |
| /* ID of the Internal 4 MI2S Tx port */ |
| #define AFE_PORT_ID_INT4_MI2S_TX 0x1037 |
| /* ID of the Internal 5 MI2S Rx port */ |
| #define AFE_PORT_ID_INT5_MI2S_RX 0x1038 |
| /* ID of the Internal 5 MI2S Tx port */ |
| #define AFE_PORT_ID_INT5_MI2S_TX 0x1039 |
| /* ID of the Internal 6 MI2S Rx port */ |
| #define AFE_PORT_ID_INT6_MI2S_RX 0x103A |
| /* ID of the Internal 6 MI2S Tx port */ |
| #define AFE_PORT_ID_INT6_MI2S_TX 0x103B |
| |
| #define AFE_PORT_ID_QUINARY_PCM_RX 0x103C |
| #define AFE_PORT_ID_QUINARY_PCM_TX 0x103D |
| |
| #define AFE_PORT_ID_SPDIF_RX 0x5000 |
| #define AFE_PORT_ID_RT_PROXY_PORT_001_RX 0x2000 |
| #define AFE_PORT_ID_RT_PROXY_PORT_001_TX 0x2001 |
| #define AFE_PORT_ID_INTERNAL_BT_SCO_RX 0x3000 |
| #define AFE_PORT_ID_INTERNAL_BT_SCO_TX 0x3001 |
| #define AFE_PORT_ID_INTERNAL_BT_A2DP_RX 0x3002 |
| #define AFE_PORT_ID_INTERNAL_FM_RX 0x3004 |
| #define AFE_PORT_ID_INTERNAL_FM_TX 0x3005 |
| /* SLIMbus Rx port on channel 0. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_0_RX 0x4000 |
| /* SLIMbus Tx port on channel 0. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_0_TX 0x4001 |
| /* SLIMbus Rx port on channel 1. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_1_RX 0x4002 |
| /* SLIMbus Tx port on channel 1. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_1_TX 0x4003 |
| /* SLIMbus Rx port on channel 2. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_2_RX 0x4004 |
| /* SLIMbus Tx port on channel 2. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_2_TX 0x4005 |
| /* SLIMbus Rx port on channel 3. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_3_RX 0x4006 |
| /* SLIMbus Tx port on channel 3. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_3_TX 0x4007 |
| /* SLIMbus Rx port on channel 4. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_4_RX 0x4008 |
| /* SLIMbus Tx port on channel 4. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_4_TX 0x4009 |
| /* SLIMbus Rx port on channel 5. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_5_RX 0x400a |
| /* SLIMbus Tx port on channel 5. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_5_TX 0x400b |
| /* SLIMbus Rx port on channel 6. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_6_RX 0x400c |
| /* SLIMbus Tx port on channel 6. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_6_TX 0x400d |
| /* SLIMbus Rx port on channel 7. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_7_RX 0x400e |
| /* SLIMbus Tx port on channel 7. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_7_TX 0x400f |
| /* SLIMbus Rx port on channel 8. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_8_RX 0x4010 |
| /* SLIMbus Tx port on channel 8. */ |
| #define AFE_PORT_ID_SLIMBUS_MULTI_CHAN_8_TX 0x4011 |
| /* AFE Rx port for audio over Display port */ |
| #define AFE_PORT_ID_HDMI_OVER_DP_RX 0x6020 |
| /*USB AFE port */ |
| #define AFE_PORT_ID_USB_RX 0x7000 |
| #define AFE_PORT_ID_USB_TX 0x7001 |
| |
| /* Generic pseudoport 1. */ |
| #define AFE_PORT_ID_PSEUDOPORT_01 0x8001 |
| /* Generic pseudoport 2. */ |
| #define AFE_PORT_ID_PSEUDOPORT_02 0x8002 |
| |
| /* @xreflabel{hdr:AfePortIdPrimaryAuxPcmTx} |
| * Primary Aux PCM Tx port ID. |
| */ |
| #define AFE_PORT_ID_PRIMARY_PCM_TX 0x100B |
| /* Pseudoport that corresponds to the voice Rx path. |
| * For recording, the voice Rx path samples are written to this |
| * port and consumed by the audio path. |
| */ |
| |
| #define AFE_PORT_ID_VOICE_RECORD_RX 0x8003 |
| |
| /* Pseudoport that corresponds to the voice Tx path. |
| * For recording, the voice Tx path samples are written to this |
| * port and consumed by the audio path. |
| */ |
| |
| #define AFE_PORT_ID_VOICE_RECORD_TX 0x8004 |
| /* Pseudoport that corresponds to in-call voice delivery samples. |
| * During in-call audio delivery, the audio path delivers samples |
| * to this port from where the voice path delivers them on the |
| * Rx path. |
| */ |
| #define AFE_PORT_ID_VOICE2_PLAYBACK_TX 0x8002 |
| #define AFE_PORT_ID_VOICE_PLAYBACK_TX 0x8005 |
| |
| #define AFE_PORT_ID_PRIMARY_TDM_RX \ |
| (AFE_PORT_ID_TDM_PORT_RANGE_START + 0x00) |
| #define AFE_PORT_ID_PRIMARY_TDM_RX_1 \ |
| (AFE_PORT_ID_PRIMARY_TDM_RX + 0x02) |
| #define AFE_PORT_ID_PRIMARY_TDM_RX_2 \ |
| (AFE_PORT_ID_PRIMARY_TDM_RX + 0x04) |
| #define AFE_PORT_ID_PRIMARY_TDM_RX_3 \ |
| (AFE_PORT_ID_PRIMARY_TDM_RX + 0x06) |
| #define AFE_PORT_ID_PRIMARY_TDM_RX_4 \ |
| (AFE_PORT_ID_PRIMARY_TDM_RX + 0x08) |
| #define AFE_PORT_ID_PRIMARY_TDM_RX_5 \ |
| (AFE_PORT_ID_PRIMARY_TDM_RX + 0x0A) |
| #define AFE_PORT_ID_PRIMARY_TDM_RX_6 \ |
| (AFE_PORT_ID_PRIMARY_TDM_RX + 0x0C) |
| #define AFE_PORT_ID_PRIMARY_TDM_RX_7 \ |
| (AFE_PORT_ID_PRIMARY_TDM_RX + 0x0E) |
| |
| #define AFE_PORT_ID_PRIMARY_TDM_TX \ |
| (AFE_PORT_ID_TDM_PORT_RANGE_START + 0x01) |
| #define AFE_PORT_ID_PRIMARY_TDM_TX_1 \ |
| (AFE_PORT_ID_PRIMARY_TDM_TX + 0x02) |
| #define AFE_PORT_ID_PRIMARY_TDM_TX_2 \ |
| (AFE_PORT_ID_PRIMARY_TDM_TX + 0x04) |
| #define AFE_PORT_ID_PRIMARY_TDM_TX_3 \ |
| (AFE_PORT_ID_PRIMARY_TDM_TX + 0x06) |
| #define AFE_PORT_ID_PRIMARY_TDM_TX_4 \ |
| (AFE_PORT_ID_PRIMARY_TDM_TX + 0x08) |
| #define AFE_PORT_ID_PRIMARY_TDM_TX_5 \ |
| (AFE_PORT_ID_PRIMARY_TDM_TX + 0x0A) |
| #define AFE_PORT_ID_PRIMARY_TDM_TX_6 \ |
| (AFE_PORT_ID_PRIMARY_TDM_TX + 0x0C) |
| #define AFE_PORT_ID_PRIMARY_TDM_TX_7 \ |
| (AFE_PORT_ID_PRIMARY_TDM_TX + 0x0E) |
| |
| #define AFE_PORT_ID_SECONDARY_TDM_RX \ |
| (AFE_PORT_ID_TDM_PORT_RANGE_START + 0x10) |
| #define AFE_PORT_ID_SECONDARY_TDM_RX_1 \ |
| (AFE_PORT_ID_SECONDARY_TDM_RX + 0x02) |
| #define AFE_PORT_ID_SECONDARY_TDM_RX_2 \ |
| (AFE_PORT_ID_SECONDARY_TDM_RX + 0x04) |
| #define AFE_PORT_ID_SECONDARY_TDM_RX_3 \ |
| (AFE_PORT_ID_SECONDARY_TDM_RX + 0x06) |
| #define AFE_PORT_ID_SECONDARY_TDM_RX_4 \ |
| (AFE_PORT_ID_SECONDARY_TDM_RX + 0x08) |
| #define AFE_PORT_ID_SECONDARY_TDM_RX_5 \ |
| (AFE_PORT_ID_SECONDARY_TDM_RX + 0x0A) |
| #define AFE_PORT_ID_SECONDARY_TDM_RX_6 \ |
| (AFE_PORT_ID_SECONDARY_TDM_RX + 0x0C) |
| #define AFE_PORT_ID_SECONDARY_TDM_RX_7 \ |
| (AFE_PORT_ID_SECONDARY_TDM_RX + 0x0E) |
| |
| #define AFE_PORT_ID_SECONDARY_TDM_TX \ |
| (AFE_PORT_ID_TDM_PORT_RANGE_START + 0x11) |
| #define AFE_PORT_ID_SECONDARY_TDM_TX_1 \ |
| (AFE_PORT_ID_SECONDARY_TDM_TX + 0x02) |
| #define AFE_PORT_ID_SECONDARY_TDM_TX_2 \ |
| (AFE_PORT_ID_SECONDARY_TDM_TX + 0x04) |
| #define AFE_PORT_ID_SECONDARY_TDM_TX_3 \ |
| (AFE_PORT_ID_SECONDARY_TDM_TX + 0x06) |
| #define AFE_PORT_ID_SECONDARY_TDM_TX_4 \ |
| (AFE_PORT_ID_SECONDARY_TDM_TX + 0x08) |
| #define AFE_PORT_ID_SECONDARY_TDM_TX_5 \ |
| (AFE_PORT_ID_SECONDARY_TDM_TX + 0x0A) |
| #define AFE_PORT_ID_SECONDARY_TDM_TX_6 \ |
| (AFE_PORT_ID_SECONDARY_TDM_TX + 0x0C) |
| #define AFE_PORT_ID_SECONDARY_TDM_TX_7 \ |
| (AFE_PORT_ID_SECONDARY_TDM_TX + 0x0E) |
| |
| #define AFE_PORT_ID_TERTIARY_TDM_RX \ |
| (AFE_PORT_ID_TDM_PORT_RANGE_START + 0x20) |
| #define AFE_PORT_ID_TERTIARY_TDM_RX_1 \ |
| (AFE_PORT_ID_TERTIARY_TDM_RX + 0x02) |
| #define AFE_PORT_ID_TERTIARY_TDM_RX_2 \ |
| (AFE_PORT_ID_TERTIARY_TDM_RX + 0x04) |
| #define AFE_PORT_ID_TERTIARY_TDM_RX_3 \ |
| (AFE_PORT_ID_TERTIARY_TDM_RX + 0x06) |
| #define AFE_PORT_ID_TERTIARY_TDM_RX_4 \ |
| (AFE_PORT_ID_TERTIARY_TDM_RX + 0x08) |
| #define AFE_PORT_ID_TERTIARY_TDM_RX_5 \ |
| (AFE_PORT_ID_TERTIARY_TDM_RX + 0x0A) |
| #define AFE_PORT_ID_TERTIARY_TDM_RX_6 \ |
| (AFE_PORT_ID_TERTIARY_TDM_RX + 0x0C) |
| #define AFE_PORT_ID_TERTIARY_TDM_RX_7 \ |
| (AFE_PORT_ID_TERTIARY_TDM_RX + 0x0E) |
| |
| #define AFE_PORT_ID_TERTIARY_TDM_TX \ |
| (AFE_PORT_ID_TDM_PORT_RANGE_START + 0x21) |
| #define AFE_PORT_ID_TERTIARY_TDM_TX_1 \ |
| (AFE_PORT_ID_TERTIARY_TDM_TX + 0x02) |
| #define AFE_PORT_ID_TERTIARY_TDM_TX_2 \ |
| (AFE_PORT_ID_TERTIARY_TDM_TX + 0x04) |
| #define AFE_PORT_ID_TERTIARY_TDM_TX_3 \ |
| (AFE_PORT_ID_TERTIARY_TDM_TX + 0x06) |
| #define AFE_PORT_ID_TERTIARY_TDM_TX_4 \ |
| (AFE_PORT_ID_TERTIARY_TDM_TX + 0x08) |
| #define AFE_PORT_ID_TERTIARY_TDM_TX_5 \ |
| (AFE_PORT_ID_TERTIARY_TDM_TX + 0x0A) |
| #define AFE_PORT_ID_TERTIARY_TDM_TX_6 \ |
| (AFE_PORT_ID_TERTIARY_TDM_TX + 0x0C) |
| #define AFE_PORT_ID_TERTIARY_TDM_TX_7 \ |
| (AFE_PORT_ID_TERTIARY_TDM_TX + 0x0E) |
| |
| #define AFE_PORT_ID_QUATERNARY_TDM_RX \ |
| (AFE_PORT_ID_TDM_PORT_RANGE_START + 0x30) |
| #define AFE_PORT_ID_QUATERNARY_TDM_RX_1 \ |
| (AFE_PORT_ID_QUATERNARY_TDM_RX + 0x02) |
| #define AFE_PORT_ID_QUATERNARY_TDM_RX_2 \ |
| (AFE_PORT_ID_QUATERNARY_TDM_RX + 0x04) |
| #define AFE_PORT_ID_QUATERNARY_TDM_RX_3 \ |
| (AFE_PORT_ID_QUATERNARY_TDM_RX + 0x06) |
| #define AFE_PORT_ID_QUATERNARY_TDM_RX_4 \ |
| (AFE_PORT_ID_QUATERNARY_TDM_RX + 0x08) |
| #define AFE_PORT_ID_QUATERNARY_TDM_RX_5 \ |
| (AFE_PORT_ID_QUATERNARY_TDM_RX + 0x0A) |
| #define AFE_PORT_ID_QUATERNARY_TDM_RX_6 \ |
| (AFE_PORT_ID_QUATERNARY_TDM_RX + 0x0C) |
| #define AFE_PORT_ID_QUATERNARY_TDM_RX_7 \ |
| (AFE_PORT_ID_QUATERNARY_TDM_RX + 0x0E) |
| |
| #define AFE_PORT_ID_QUATERNARY_TDM_TX \ |
| (AFE_PORT_ID_TDM_PORT_RANGE_START + 0x31) |
| #define AFE_PORT_ID_QUATERNARY_TDM_TX_1 \ |
| (AFE_PORT_ID_QUATERNARY_TDM_TX + 0x02) |
| #define AFE_PORT_ID_QUATERNARY_TDM_TX_2 \ |
| (AFE_PORT_ID_QUATERNARY_TDM_TX + 0x04) |
| #define AFE_PORT_ID_QUATERNARY_TDM_TX_3 \ |
| (AFE_PORT_ID_QUATERNARY_TDM_TX + 0x06) |
| #define AFE_PORT_ID_QUATERNARY_TDM_TX_4 \ |
| (AFE_PORT_ID_QUATERNARY_TDM_TX + 0x08) |
| #define AFE_PORT_ID_QUATERNARY_TDM_TX_5 \ |
| (AFE_PORT_ID_QUATERNARY_TDM_TX + 0x0A) |
| #define AFE_PORT_ID_QUATERNARY_TDM_TX_6 \ |
| (AFE_PORT_ID_QUATERNARY_TDM_TX + 0x0C) |
| #define AFE_PORT_ID_QUATERNARY_TDM_TX_7 \ |
| (AFE_PORT_ID_QUATERNARY_TDM_TX + 0x0E) |
| |
| #define AFE_PORT_ID_QUINARY_TDM_RX \ |
| (AFE_PORT_ID_TDM_PORT_RANGE_START + 0x40) |
| #define AFE_PORT_ID_QUINARY_TDM_RX_1 \ |
| (AFE_PORT_ID_QUINARY_TDM_RX + 0x02) |
| #define AFE_PORT_ID_QUINARY_TDM_RX_2 \ |
| (AFE_PORT_ID_QUINARY_TDM_RX + 0x04) |
| #define AFE_PORT_ID_QUINARY_TDM_RX_3 \ |
| (AFE_PORT_ID_QUINARY_TDM_RX + 0x06) |
| #define AFE_PORT_ID_QUINARY_TDM_RX_4 \ |
| (AFE_PORT_ID_QUINARY_TDM_RX + 0x08) |
| #define AFE_PORT_ID_QUINARY_TDM_RX_5 \ |
| (AFE_PORT_ID_QUINARY_TDM_RX + 0x0A) |
| #define AFE_PORT_ID_QUINARY_TDM_RX_6 \ |
| (AFE_PORT_ID_QUINARY_TDM_RX + 0x0C) |
| #define AFE_PORT_ID_QUINARY_TDM_RX_7 \ |
| (AFE_PORT_ID_QUINARY_TDM_RX + 0x0E) |
| |
| #define AFE_PORT_ID_QUINARY_TDM_TX \ |
| (AFE_PORT_ID_TDM_PORT_RANGE_START + 0x41) |
| #define AFE_PORT_ID_QUINARY_TDM_TX_1 \ |
| (AFE_PORT_ID_QUINARY_TDM_TX + 0x02) |
| #define AFE_PORT_ID_QUINARY_TDM_TX_2 \ |
| (AFE_PORT_ID_QUINARY_TDM_TX + 0x04) |
| #define AFE_PORT_ID_QUINARY_TDM_TX_3 \ |
| (AFE_PORT_ID_QUINARY_TDM_TX + 0x06) |
| #define AFE_PORT_ID_QUINARY_TDM_TX_4 \ |
| (AFE_PORT_ID_QUINARY_TDM_TX + 0x08) |
| #define AFE_PORT_ID_QUINARY_TDM_TX_5 \ |
| (AFE_PORT_ID_QUINARY_TDM_TX + 0x0A) |
| #define AFE_PORT_ID_QUINARY_TDM_TX_6 \ |
| (AFE_PORT_ID_QUINARY_TDM_TX + 0x0C) |
| #define AFE_PORT_ID_QUINARY_TDM_TX_7 \ |
| (AFE_PORT_ID_QUINARY_TDM_TX + 0x0E) |
| |
| #define AFE_PORT_ID_INVALID 0xFFFF |
| |
| #define AAC_ENC_MODE_AAC_LC 0x02 |
| #define AAC_ENC_MODE_AAC_P 0x05 |
| #define AAC_ENC_MODE_EAAC_P 0x1D |
| |
| #define AFE_PSEUDOPORT_CMD_START 0x000100cf |
| struct afe_pseudoport_start_command { |
| struct apr_hdr hdr; |
| u16 port_id; /* Pseudo Port 1 = 0x8000 */ |
| /* Pseudo Port 2 = 0x8001 */ |
| /* Pseudo Port 3 = 0x8002 */ |
| u16 timing; /* FTRT = 0 , AVTimer = 1, */ |
| } __packed; |
| |
| #define AFE_PSEUDOPORT_CMD_STOP 0x000100d0 |
| struct afe_pseudoport_stop_command { |
| struct apr_hdr hdr; |
| u16 port_id; /* Pseudo Port 1 = 0x8000 */ |
| /* Pseudo Port 2 = 0x8001 */ |
| /* Pseudo Port 3 = 0x8002 */ |
| u16 reserved; |
| } __packed; |
| |
| |
| #define AFE_MODULE_SIDETONE_IIR_FILTER 0x00010202 |
| #define AFE_PARAM_ID_ENABLE 0x00010203 |
| |
| /* Payload of the #AFE_PARAM_ID_ENABLE |
| * parameter, which enables or |
| * disables any module. |
| * The fixed size of this structure is four bytes. |
| */ |
| |
| struct afe_mod_enable_param { |
| u16 enable; |
| /* Enables (1) or disables (0) the module. */ |
| |
| u16 reserved; |
| /* This field must be set to zero. */ |
| } __packed; |
| |
| /* ID of the configuration parameter used by the |
| * #AFE_MODULE_SIDETONE_IIR_FILTER module. |
| */ |
| #define AFE_PARAM_ID_SIDETONE_IIR_FILTER_CONFIG 0x00010204 |
| #define MAX_SIDETONE_IIR_DATA_SIZE 224 |
| #define MAX_NO_IIR_FILTER_STAGE 10 |
| |
| struct afe_sidetone_iir_filter_config_params { |
| u16 num_biquad_stages; |
| /* Number of stages. |
| * Supported values: Minimum of 5 and maximum of 10 |
| */ |
| |
| u16 pregain; |
| /* Pregain for the compensating filter response. |
| * Supported values: Any number in Q13 format |
| */ |
| uint8_t iir_config[MAX_SIDETONE_IIR_DATA_SIZE]; |
| } __packed; |
| |
| #define AFE_MODULE_LOOPBACK 0x00010205 |
| #define AFE_PARAM_ID_LOOPBACK_GAIN_PER_PATH 0x00010206 |
| |
| /* Payload of the #AFE_PARAM_ID_LOOPBACK_GAIN_PER_PATH parameter, |
| * which gets/sets loopback gain of a port to an Rx port. |
| * The Tx port ID of the loopback is part of the set_param command. |
| */ |
| |
| /* Payload of the #AFE_PORT_CMD_SET_PARAM_V2 command's |
| * configuration/calibration settings for the AFE port. |
| */ |
| struct afe_port_cmd_set_param_v2 { |
| u16 port_id; |
| /* Port interface and direction (Rx or Tx) to start. */ |
| |
| u16 payload_size; |
| /* Actual size of the payload in bytes. |
| * This is used for parsing the parameter payload. |
| * Supported values: > 0 |
| */ |
| |
| u32 payload_address_lsw; |
| /* LSW of 64 bit Payload address. |
| * Address should be 32-byte, |
| * 4kbyte aligned and must be contiguous memory. |
| */ |
| |
| u32 payload_address_msw; |
| /* MSW of 64 bit Payload address. |
| * In case of 32-bit shared memory address, |
| * this field must be set to zero. |
| * In case of 36-bit shared memory address, |
| * bit-4 to bit-31 must be set to zero. |
| * Address should be 32-byte, 4kbyte aligned |
| * and must be contiguous memory. |
| */ |
| |
| u32 mem_map_handle; |
| /* Memory map handle returned by |
| * AFE_SERVICE_CMD_SHARED_MEM_MAP_REGIONS commands. |
| * Supported Values: |
| * - NULL -- Message. The parameter data is in-band. |
| * - Non-NULL -- The parameter data is Out-band.Pointer to |
| * the physical address |
| * in shared memory of the payload data. |
| * An optional field is available if parameter |
| * data is in-band: |
| * afe_param_data_v2 param_data[...]. |
| * For detailed payload content, see the |
| * afe_port_param_data_v2 structure. |
| */ |
| } __packed; |
| |
| #define AFE_PORT_CMD_SET_PARAM_V2 0x000100EF |
| |
| struct afe_port_param_data_v2 { |
| u32 module_id; |
| /* ID of the module to be configured. |
| * Supported values: Valid module ID |
| */ |
| |
| u32 param_id; |
| /* ID of the parameter corresponding to the supported parameters |
| * for the module ID. |
| * Supported values: Valid parameter ID |
| */ |
| |
| u16 param_size; |
| /* Actual size of the data for the |
| * module_id/param_id pair. The size is a |
| * multiple of four bytes. |
| * Supported values: > 0 |
| */ |
| |
| u16 reserved; |
| /* This field must be set to zero. |
| */ |
| } __packed; |
| |
| struct afe_loopback_gain_per_path_param { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| u16 rx_port_id; |
| /* Rx port of the loopback. */ |
| |
| u16 gain; |
| /* Loopback gain per path of the port. |
| * Supported values: Any number in Q13 format |
| */ |
| } __packed; |
| |
| /* Parameter ID used to configure and enable/disable the |
| * loopback path. The difference with respect to the existing |
| * API, AFE_PORT_CMD_LOOPBACK, is that it allows Rx port to be |
| * configured as source port in loopback path. Port-id in |
| * AFE_PORT_CMD_SET_PARAM cmd is the source port which can be |
| * Tx or Rx port. In addition, we can configure the type of |
| * routing mode to handle different use cases. |
| */ |
| #define AFE_PARAM_ID_LOOPBACK_CONFIG 0x0001020B |
| #define AFE_API_VERSION_LOOPBACK_CONFIG 0x1 |
| |
| enum afe_loopback_routing_mode { |
| LB_MODE_DEFAULT = 1, |
| /* Regular loopback from source to destination port */ |
| LB_MODE_SIDETONE, |
| /* Sidetone feed from Tx source to Rx destination port */ |
| LB_MODE_EC_REF_VOICE_AUDIO, |
| /* Echo canceller reference, voice + audio + DTMF */ |
| LB_MODE_EC_REF_VOICE |
| /* Echo canceller reference, voice alone */ |
| } __packed; |
| |
| /* Payload of the #AFE_PARAM_ID_LOOPBACK_CONFIG , |
| * which enables/disables one AFE loopback. |
| */ |
| struct afe_loopback_cfg_v1 { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| u32 loopback_cfg_minor_version; |
| /* Minor version used for tracking the version of the RMC module |
| * configuration interface. |
| * Supported values: #AFE_API_VERSION_LOOPBACK_CONFIG |
| */ |
| u16 dst_port_id; |
| /* Destination Port Id. */ |
| u16 routing_mode; |
| /* Specifies data path type from src to dest port. |
| * Supported values: |
| * #LB_MODE_DEFAULT |
| * #LB_MODE_SIDETONE |
| * #LB_MODE_EC_REF_VOICE_AUDIO |
| * #LB_MODE_EC_REF_VOICE_A |
| * #LB_MODE_EC_REF_VOICE |
| */ |
| |
| u16 enable; |
| /* Specifies whether to enable (1) or |
| * disable (0) an AFE loopback. |
| */ |
| u16 reserved; |
| /* Reserved for 32-bit alignment. This field must be set to 0. |
| */ |
| |
| } __packed; |
| |
| struct afe_loopback_sidetone_gain { |
| u16 rx_port_id; |
| u16 gain; |
| } __packed; |
| |
| struct loopback_cfg_data { |
| u32 loopback_cfg_minor_version; |
| /* Minor version used for tracking the version of the RMC module |
| * configuration interface. |
| * Supported values: #AFE_API_VERSION_LOOPBACK_CONFIG |
| */ |
| u16 dst_port_id; |
| /* Destination Port Id. */ |
| u16 routing_mode; |
| /* Specifies data path type from src to dest port. |
| * Supported values: |
| * #LB_MODE_DEFAULT |
| * #LB_MODE_SIDETONE |
| * #LB_MODE_EC_REF_VOICE_AUDIO |
| * #LB_MODE_EC_REF_VOICE_A |
| * #LB_MODE_EC_REF_VOICE |
| */ |
| |
| u16 enable; |
| /* Specifies whether to enable (1) or |
| * disable (0) an AFE loopback. |
| */ |
| u16 reserved; |
| /* Reserved for 32-bit alignment. This field must be set to 0. |
| */ |
| } __packed; |
| |
| struct afe_st_loopback_cfg_v1 { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 gain_pdata; |
| struct afe_loopback_sidetone_gain gain_data; |
| struct afe_port_param_data_v2 cfg_pdata; |
| struct loopback_cfg_data cfg_data; |
| } __packed; |
| |
| struct afe_loopback_iir_cfg_v2 { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 st_iir_enable_pdata; |
| struct afe_mod_enable_param st_iir_mode_enable_data; |
| struct afe_port_param_data_v2 st_iir_filter_config_pdata; |
| struct afe_sidetone_iir_filter_config_params st_iir_filter_config_data; |
| } __packed; |
| #define AFE_MODULE_SPEAKER_PROTECTION 0x00010209 |
| #define AFE_PARAM_ID_SPKR_PROT_CONFIG 0x0001020a |
| #define AFE_API_VERSION_SPKR_PROT_CONFIG 0x1 |
| #define AFE_SPKR_PROT_EXCURSIONF_LEN 512 |
| struct afe_spkr_prot_cfg_param_v1 { |
| u32 spkr_prot_minor_version; |
| /* |
| * Minor version used for tracking the version of the |
| * speaker protection module configuration interface. |
| * Supported values: #AFE_API_VERSION_SPKR_PROT_CONFIG |
| */ |
| |
| int16_t win_size; |
| /* Analysis and synthesis window size (nWinSize). |
| * Supported values: 1024, 512, 256 samples |
| */ |
| |
| int16_t margin; |
| /* Allowable margin for excursion prediction, |
| * in L16Q15 format. This is a |
| * control parameter to allow |
| * for overestimation of peak excursion. |
| */ |
| |
| int16_t spkr_exc_limit; |
| /* Speaker excursion limit, in L16Q15 format.*/ |
| |
| int16_t spkr_resonance_freq; |
| /* Resonance frequency of the speaker; used |
| * to define a frequency range |
| * for signal modification. |
| * |
| * Supported values: 0 to 2000 Hz |
| */ |
| |
| int16_t limhresh; |
| /* Threshold of the hard limiter; used to |
| * prevent overshooting beyond a |
| * signal level that was set by the limiter |
| * prior to speaker protection. |
| * Supported values: 0 to 32767 |
| */ |
| |
| int16_t hpf_cut_off_freq; |
| /* High pass filter cutoff frequency. |
| * Supported values: 100, 200, 300 Hz |
| */ |
| |
| int16_t hpf_enable; |
| /* Specifies whether the high pass filter |
| * is enabled (0) or disabled (1). |
| */ |
| |
| int16_t reserved; |
| /* This field must be set to zero. */ |
| |
| int32_t amp_gain; |
| /* Amplifier gain in L32Q15 format. |
| * This is the RMS voltage at the |
| * loudspeaker when a 0dBFS tone |
| * is played in the digital domain. |
| */ |
| |
| int16_t excursionf[AFE_SPKR_PROT_EXCURSIONF_LEN]; |
| /* Array of the excursion transfer function. |
| * The peak excursion of the |
| * loudspeaker diaphragm is |
| * measured in millimeters for 1 Vrms Sine |
| * tone at all FFT bin frequencies. |
| * Supported values: Q15 format |
| */ |
| } __packed; |
| |
| |
| #define AFE_SERVICE_CMD_REGISTER_RT_PORT_DRIVER 0x000100E0 |
| |
| /* Payload of the #AFE_SERVICE_CMD_REGISTER_RT_PORT_DRIVER |
| * command, which registers a real-time port driver |
| * with the AFE service. |
| */ |
| struct afe_service_cmd_register_rt_port_driver { |
| struct apr_hdr hdr; |
| u16 port_id; |
| /* Port ID with which the real-time driver exchanges data |
| * (registers for events). |
| * Supported values: #AFE_PORT_ID_RT_PROXY_PORT_RANGE_START to |
| * #AFE_PORT_ID_RT_PROXY_PORT_RANGE_END |
| */ |
| |
| u16 reserved; |
| /* This field must be set to zero. */ |
| } __packed; |
| |
| #define AFE_SERVICE_CMD_UNREGISTER_RT_PORT_DRIVER 0x000100E1 |
| |
| /* Payload of the #AFE_SERVICE_CMD_UNREGISTER_RT_PORT_DRIVER |
| * command, which unregisters a real-time port driver from |
| * the AFE service. |
| */ |
| struct afe_service_cmd_unregister_rt_port_driver { |
| struct apr_hdr hdr; |
| u16 port_id; |
| /* Port ID from which the real-time |
| * driver unregisters for events. |
| * Supported values: #AFE_PORT_ID_RT_PROXY_PORT_RANGE_START to |
| * #AFE_PORT_ID_RT_PROXY_PORT_RANGE_END |
| */ |
| |
| u16 reserved; |
| /* This field must be set to zero. */ |
| } __packed; |
| |
| #define AFE_EVENT_RT_PROXY_PORT_STATUS 0x00010105 |
| #define AFE_EVENTYPE_RT_PROXY_PORT_START 0 |
| #define AFE_EVENTYPE_RT_PROXY_PORT_STOP 1 |
| #define AFE_EVENTYPE_RT_PROXY_PORT_LOW_WATER_MARK 2 |
| #define AFE_EVENTYPE_RT_PROXY_PORT_HIGH_WATER_MARK 3 |
| #define AFE_EVENTYPE_RT_PROXY_PORT_INVALID 0xFFFF |
| |
| /* Payload of the #AFE_EVENT_RT_PROXY_PORT_STATUS |
| * message, which sends an event from the AFE service |
| * to a registered client. |
| */ |
| struct afe_event_rt_proxy_port_status { |
| u16 port_id; |
| /* Port ID to which the event is sent. |
| * Supported values: #AFE_PORT_ID_RT_PROXY_PORT_RANGE_START to |
| * #AFE_PORT_ID_RT_PROXY_PORT_RANGE_END |
| */ |
| |
| u16 eventype; |
| /* Type of event. |
| * Supported values: |
| * - #AFE_EVENTYPE_RT_PROXY_PORT_START |
| * - #AFE_EVENTYPE_RT_PROXY_PORT_STOP |
| * - #AFE_EVENTYPE_RT_PROXY_PORT_LOW_WATER_MARK |
| * - #AFE_EVENTYPE_RT_PROXY_PORT_HIGH_WATER_MARK |
| */ |
| } __packed; |
| |
| #define AFE_PORT_DATA_CMD_RT_PROXY_PORT_WRITE_V2 0x000100ED |
| |
| struct afe_port_data_cmd_rt_proxy_port_write_v2 { |
| struct apr_hdr hdr; |
| u16 port_id; |
| /* Tx (mic) proxy port ID with which the real-time |
| * driver exchanges data. |
| * Supported values: #AFE_PORT_ID_RT_PROXY_PORT_RANGE_START to |
| * #AFE_PORT_ID_RT_PROXY_PORT_RANGE_END |
| */ |
| |
| u16 reserved; |
| /* This field must be set to zero. */ |
| |
| u32 buffer_address_lsw; |
| /* LSW Address of the buffer containing the |
| * data from the real-time source |
| * device on a client. |
| */ |
| |
| u32 buffer_address_msw; |
| /* MSW Address of the buffer containing the |
| * data from the real-time source |
| * device on a client. |
| */ |
| |
| u32 mem_map_handle; |
| /* A memory map handle encapsulating shared memory |
| * attributes is returned if |
| * AFE_SERVICE_CMD_SHARED_MEM_MAP_REGIONS |
| * command is successful. |
| * Supported Values: |
| * - Any 32 bit value |
| */ |
| |
| u32 available_bytes; |
| /* Number of valid bytes available |
| * in the buffer (including all |
| * channels: number of bytes per |
| * channel = availableBytesumChannels). |
| * Supported values: > 0 |
| * |
| * This field must be equal to the frame |
| * size specified in the #AFE_PORT_AUDIO_IF_CONFIG |
| * command that was sent to configure this |
| * port. |
| */ |
| } __packed; |
| |
| #define AFE_PORT_DATA_CMD_RT_PROXY_PORT_READ_V2 0x000100EE |
| |
| /* Payload of the |
| * #AFE_PORT_DATA_CMD_RT_PROXY_PORT_READ_V2 command, which |
| * delivers an empty buffer to the AFE service. On |
| * acknowledgment, data is filled in the buffer. |
| */ |
| struct afe_port_data_cmd_rt_proxy_port_read_v2 { |
| struct apr_hdr hdr; |
| u16 port_id; |
| /* Rx proxy port ID with which the real-time |
| * driver exchanges data. |
| * Supported values: #AFE_PORT_ID_RT_PROXY_PORT_RANGE_START to |
| * #AFE_PORT_ID_RT_PROXY_PORT_RANGE_END |
| * (This must be an Rx (speaker) port.) |
| */ |
| |
| u16 reserved; |
| /* This field must be set to zero. */ |
| |
| u32 buffer_address_lsw; |
| /* LSW Address of the buffer containing the data sent from the AFE |
| * service to a real-time sink device on the client. |
| */ |
| |
| |
| u32 buffer_address_msw; |
| /* MSW Address of the buffer containing the data sent from the AFE |
| * service to a real-time sink device on the client. |
| */ |
| |
| u32 mem_map_handle; |
| /* A memory map handle encapsulating shared memory attributes is |
| * returned if AFE_SERVICE_CMD_SHARED_MEM_MAP_REGIONS command is |
| * successful. |
| * Supported Values: |
| * - Any 32 bit value |
| */ |
| |
| u32 available_bytes; |
| /* Number of valid bytes available in the buffer (including all |
| * channels). |
| * Supported values: > 0 |
| * This field must be equal to the frame size specified in the |
| * #AFE_PORT_AUDIO_IF_CONFIG command that was sent to configure |
| * this port. |
| */ |
| } __packed; |
| |
| /* This module ID is related to device configuring like I2S,PCM, |
| * HDMI, SLIMBus etc. This module supports following parameter ids. |
| * - #AFE_PARAM_ID_I2S_CONFIG |
| * - #AFE_PARAM_ID_PCM_CONFIG |
| * - #AFE_PARAM_ID_DIGI_MIC_CONFIG |
| * - #AFE_PARAM_ID_HDMI_CONFIG |
| * - #AFE_PARAM_ID_INTERNAL_BT_FM_CONFIG |
| * - #AFE_PARAM_ID_SLIMBUS_CONFIG |
| * - #AFE_PARAM_ID_RT_PROXY_CONFIG |
| */ |
| |
| #define AFE_MODULE_AUDIO_DEV_INTERFACE 0x0001020C |
| #define AFE_PORT_SAMPLE_RATE_8K 8000 |
| #define AFE_PORT_SAMPLE_RATE_16K 16000 |
| #define AFE_PORT_SAMPLE_RATE_48K 48000 |
| #define AFE_PORT_SAMPLE_RATE_96K 96000 |
| #define AFE_PORT_SAMPLE_RATE_176P4K 176400 |
| #define AFE_PORT_SAMPLE_RATE_192K 192000 |
| #define AFE_PORT_SAMPLE_RATE_352P8K 352800 |
| #define AFE_LINEAR_PCM_DATA 0x0 |
| #define AFE_NON_LINEAR_DATA 0x1 |
| #define AFE_LINEAR_PCM_DATA_PACKED_60958 0x2 |
| #define AFE_NON_LINEAR_DATA_PACKED_60958 0x3 |
| #define AFE_GENERIC_COMPRESSED 0x8 |
| |
| /* This param id is used to configure I2S interface */ |
| #define AFE_PARAM_ID_I2S_CONFIG 0x0001020D |
| #define AFE_API_VERSION_I2S_CONFIG 0x1 |
| /* Enumeration for setting the I2S configuration |
| * channel_mode parameter to |
| * serial data wire number 1-3 (SD3). |
| */ |
| #define AFE_PORT_I2S_SD0 0x1 |
| #define AFE_PORT_I2S_SD1 0x2 |
| #define AFE_PORT_I2S_SD2 0x3 |
| #define AFE_PORT_I2S_SD3 0x4 |
| #define AFE_PORT_I2S_QUAD01 0x5 |
| #define AFE_PORT_I2S_QUAD23 0x6 |
| #define AFE_PORT_I2S_6CHS 0x7 |
| #define AFE_PORT_I2S_8CHS 0x8 |
| #define AFE_PORT_I2S_MONO 0x0 |
| #define AFE_PORT_I2S_STEREO 0x1 |
| #define AFE_PORT_CONFIG_I2S_WS_SRC_EXTERNAL 0x0 |
| #define AFE_PORT_CONFIG_I2S_WS_SRC_INTERNAL 0x1 |
| |
| /* Payload of the #AFE_PARAM_ID_I2S_CONFIG |
| * command's (I2S configuration |
| * parameter). |
| */ |
| struct afe_param_id_i2s_cfg { |
| u32 i2s_cfg_minor_version; |
| /* Minor version used for tracking the version of the I2S |
| * configuration interface. |
| * Supported values: #AFE_API_VERSION_I2S_CONFIG |
| */ |
| |
| u16 bit_width; |
| /* Bit width of the sample. |
| * Supported values: 16, 24 |
| */ |
| |
| u16 channel_mode; |
| /* I2S lines and multichannel operation. |
| * Supported values: |
| * - #AFE_PORT_I2S_SD0 |
| * - #AFE_PORT_I2S_SD1 |
| * - #AFE_PORT_I2S_SD2 |
| * - #AFE_PORT_I2S_SD3 |
| * - #AFE_PORT_I2S_QUAD01 |
| * - #AFE_PORT_I2S_QUAD23 |
| * - #AFE_PORT_I2S_6CHS |
| * - #AFE_PORT_I2S_8CHS |
| */ |
| |
| u16 mono_stereo; |
| /* Specifies mono or stereo. This applies only when |
| * a single I2S line is used. |
| * Supported values: |
| * - #AFE_PORT_I2S_MONO |
| * - #AFE_PORT_I2S_STEREO |
| */ |
| |
| u16 ws_src; |
| /* Word select source: internal or external. |
| * Supported values: |
| * - #AFE_PORT_CONFIG_I2S_WS_SRC_EXTERNAL |
| * - #AFE_PORT_CONFIG_I2S_WS_SRC_INTERNAL |
| */ |
| |
| u32 sample_rate; |
| /* Sampling rate of the port. |
| * Supported values: |
| * - #AFE_PORT_SAMPLE_RATE_8K |
| * - #AFE_PORT_SAMPLE_RATE_16K |
| * - #AFE_PORT_SAMPLE_RATE_48K |
| * - #AFE_PORT_SAMPLE_RATE_96K |
| * - #AFE_PORT_SAMPLE_RATE_192K |
| */ |
| |
| u16 data_format; |
| /* data format |
| * Supported values: |
| * - #LINEAR_PCM_DATA |
| * - #NON_LINEAR_DATA |
| * - #LINEAR_PCM_DATA_PACKED_IN_60958 |
| * - #NON_LINEAR_DATA_PACKED_IN_60958 |
| */ |
| u16 reserved; |
| /* This field must be set to zero. */ |
| } __packed; |
| |
| /* |
| * This param id is used to configure PCM interface |
| */ |
| |
| #define AFE_API_VERSION_SPDIF_CONFIG 0x1 |
| #define AFE_API_VERSION_SPDIF_CH_STATUS_CONFIG 0x1 |
| #define AFE_API_VERSION_SPDIF_CLK_CONFIG 0x1 |
| #define AFE_CH_STATUS_A 1 |
| #define AFE_CH_STATUS_B 2 |
| |
| #define AFE_PARAM_ID_SPDIF_CONFIG 0x00010244 |
| #define AFE_PARAM_ID_CH_STATUS_CONFIG 0x00010245 |
| #define AFE_PARAM_ID_SPDIF_CLK_CONFIG 0x00010246 |
| |
| #define AFE_PORT_CLK_ROOT_LPAPLL 0x3 |
| #define AFE_PORT_CLK_ROOT_LPAQ6PLL 0x4 |
| |
| struct afe_param_id_spdif_cfg { |
| /* Minor version used for tracking the version of the SPDIF |
| * configuration interface. |
| * Supported values: #AFE_API_VERSION_SPDIF_CONFIG |
| */ |
| u32 spdif_cfg_minor_version; |
| |
| /* Sampling rate of the port. |
| * Supported values: |
| * - #AFE_PORT_SAMPLE_RATE_22_05K |
| * - #AFE_PORT_SAMPLE_RATE_32K |
| * - #AFE_PORT_SAMPLE_RATE_44_1K |
| * - #AFE_PORT_SAMPLE_RATE_48K |
| * - #AFE_PORT_SAMPLE_RATE_96K |
| * - #AFE_PORT_SAMPLE_RATE_176_4K |
| * - #AFE_PORT_SAMPLE_RATE_192K |
| */ |
| u32 sample_rate; |
| |
| /* data format |
| * Supported values: |
| * - #AFE_LINEAR_PCM_DATA |
| * - #AFE_NON_LINEAR_DATA |
| */ |
| u16 data_format; |
| /* Number of channels supported by the port |
| * - PCM - 1, Compressed Case - 2 |
| */ |
| u16 num_channels; |
| /* Bit width of the sample. |
| * Supported values: 16, 24 |
| */ |
| u16 bit_width; |
| /* This field must be set to zero. */ |
| u16 reserved; |
| } __packed; |
| |
| struct afe_param_id_spdif_ch_status_cfg { |
| u32 ch_status_cfg_minor_version; |
| /* Minor version used for tracking the version of channel |
| * status configuration. Current supported version is 1 |
| */ |
| |
| u32 status_type; |
| /* Indicate if the channel status is for channel A or B |
| * Supported values: |
| * - #AFE_CH_STATUS_A |
| * - #AFE_CH_STATUS_B |
| */ |
| |
| u8 status_bits[24]; |
| /* Channel status - 192 bits for channel |
| * Byte ordering as defined by IEC60958-3 |
| */ |
| |
| u8 status_mask[24]; |
| /* Channel status with mask bits 1 will be applied. |
| * Byte ordering as defined by IEC60958-3 |
| */ |
| } __packed; |
| |
| struct afe_param_id_spdif_clk_cfg { |
| u32 clk_cfg_minor_version; |
| /* Minor version used for tracking the version of SPDIF |
| * interface clock configuration. Current supported version |
| * is 1 |
| */ |
| |
| u32 clk_value; |
| /* Specifies the clock frequency in Hz to set |
| * Supported values: |
| * 0 - Disable the clock |
| * 2 (byphase) * 32 (60958 subframe size) * sampling rate * 2 |
| * (channels A and B) |
| */ |
| |
| u32 clk_root; |
| /* Specifies SPDIF root clk source |
| * Supported Values: |
| * - #AFE_PORT_CLK_ROOT_LPAPLL |
| * - #AFE_PORT_CLK_ROOT_LPAQ6PLL |
| */ |
| } __packed; |
| |
| struct afe_spdif_clk_config_command { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_param_id_spdif_clk_cfg clk_cfg; |
| } __packed; |
| |
| struct afe_spdif_chstatus_config_command { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_param_id_spdif_ch_status_cfg ch_status; |
| } __packed; |
| |
| struct afe_spdif_port_config { |
| struct afe_param_id_spdif_cfg cfg; |
| struct afe_param_id_spdif_ch_status_cfg ch_status; |
| } __packed; |
| |
| #define AFE_PARAM_ID_PCM_CONFIG 0x0001020E |
| #define AFE_API_VERSION_PCM_CONFIG 0x1 |
| /* Enumeration for the auxiliary PCM synchronization signal |
| * provided by an external source. |
| */ |
| |
| #define AFE_PORT_PCM_SYNC_SRC_EXTERNAL 0x0 |
| /* Enumeration for the auxiliary PCM synchronization signal |
| * provided by an internal source. |
| */ |
| #define AFE_PORT_PCM_SYNC_SRC_INTERNAL 0x1 |
| /* Enumeration for the PCM configuration aux_mode parameter, |
| * which configures the auxiliary PCM interface to use |
| * short synchronization. |
| */ |
| #define AFE_PORT_PCM_AUX_MODE_PCM 0x0 |
| /* |
| * Enumeration for the PCM configuration aux_mode parameter, |
| * which configures the auxiliary PCM interface to use long |
| * synchronization. |
| */ |
| #define AFE_PORT_PCM_AUX_MODE_AUX 0x1 |
| /* |
| * Enumeration for setting the PCM configuration frame to 8. |
| */ |
| #define AFE_PORT_PCM_BITS_PER_FRAME_8 0x0 |
| /* |
| * Enumeration for setting the PCM configuration frame to 16. |
| */ |
| #define AFE_PORT_PCM_BITS_PER_FRAME_16 0x1 |
| |
| /* Enumeration for setting the PCM configuration frame to 32.*/ |
| #define AFE_PORT_PCM_BITS_PER_FRAME_32 0x2 |
| |
| /* Enumeration for setting the PCM configuration frame to 64.*/ |
| #define AFE_PORT_PCM_BITS_PER_FRAME_64 0x3 |
| |
| /* Enumeration for setting the PCM configuration frame to 128.*/ |
| #define AFE_PORT_PCM_BITS_PER_FRAME_128 0x4 |
| |
| /* Enumeration for setting the PCM configuration frame to 256.*/ |
| #define AFE_PORT_PCM_BITS_PER_FRAME_256 0x5 |
| |
| /* Enumeration for setting the PCM configuration |
| * quantype parameter to A-law with no padding. |
| */ |
| #define AFE_PORT_PCM_ALAW_NOPADDING 0x0 |
| |
| /* Enumeration for setting the PCM configuration quantype |
| * parameter to mu-law with no padding. |
| */ |
| #define AFE_PORT_PCM_MULAW_NOPADDING 0x1 |
| /* Enumeration for setting the PCM configuration quantype |
| * parameter to linear with no padding. |
| */ |
| #define AFE_PORT_PCM_LINEAR_NOPADDING 0x2 |
| /* Enumeration for setting the PCM configuration quantype |
| * parameter to A-law with padding. |
| */ |
| #define AFE_PORT_PCM_ALAW_PADDING 0x3 |
| /* Enumeration for setting the PCM configuration quantype |
| * parameter to mu-law with padding. |
| */ |
| #define AFE_PORT_PCM_MULAW_PADDING 0x4 |
| /* Enumeration for setting the PCM configuration quantype |
| * parameter to linear with padding. |
| */ |
| #define AFE_PORT_PCM_LINEAR_PADDING 0x5 |
| /* Enumeration for disabling the PCM configuration |
| * ctrl_data_out_enable parameter. |
| * The PCM block is the only master. |
| */ |
| #define AFE_PORT_PCM_CTRL_DATA_OE_DISABLE 0x0 |
| /* |
| * Enumeration for enabling the PCM configuration |
| * ctrl_data_out_enable parameter. The PCM block shares |
| * the signal with other masters. |
| */ |
| #define AFE_PORT_PCM_CTRL_DATA_OE_ENABLE 0x1 |
| |
| /* Payload of the #AFE_PARAM_ID_PCM_CONFIG command's |
| * (PCM configuration parameter). |
| */ |
| |
| struct afe_param_id_pcm_cfg { |
| u32 pcm_cfg_minor_version; |
| /* Minor version used for tracking the version of the AUX PCM |
| * configuration interface. |
| * Supported values: #AFE_API_VERSION_PCM_CONFIG |
| */ |
| |
| u16 aux_mode; |
| /* PCM synchronization setting. |
| * Supported values: |
| * - #AFE_PORT_PCM_AUX_MODE_PCM |
| * - #AFE_PORT_PCM_AUX_MODE_AUX |
| */ |
| |
| u16 sync_src; |
| /* Synchronization source. |
| * Supported values: |
| * - #AFE_PORT_PCM_SYNC_SRC_EXTERNAL |
| * - #AFE_PORT_PCM_SYNC_SRC_INTERNAL |
| */ |
| |
| u16 frame_setting; |
| /* Number of bits per frame. |
| * Supported values: |
| * - #AFE_PORT_PCM_BITS_PER_FRAME_8 |
| * - #AFE_PORT_PCM_BITS_PER_FRAME_16 |
| * - #AFE_PORT_PCM_BITS_PER_FRAME_32 |
| * - #AFE_PORT_PCM_BITS_PER_FRAME_64 |
| * - #AFE_PORT_PCM_BITS_PER_FRAME_128 |
| * - #AFE_PORT_PCM_BITS_PER_FRAME_256 |
| */ |
| |
| u16 quantype; |
| /* PCM quantization type. |
| * Supported values: |
| * - #AFE_PORT_PCM_ALAW_NOPADDING |
| * - #AFE_PORT_PCM_MULAW_NOPADDING |
| * - #AFE_PORT_PCM_LINEAR_NOPADDING |
| * - #AFE_PORT_PCM_ALAW_PADDING |
| * - #AFE_PORT_PCM_MULAW_PADDING |
| * - #AFE_PORT_PCM_LINEAR_PADDING |
| */ |
| |
| u16 ctrl_data_out_enable; |
| /* Specifies whether the PCM block shares the data-out |
| * signal to the drive with other masters. |
| * Supported values: |
| * - #AFE_PORT_PCM_CTRL_DATA_OE_DISABLE |
| * - #AFE_PORT_PCM_CTRL_DATA_OE_ENABLE |
| */ |
| u16 reserved; |
| /* This field must be set to zero. */ |
| |
| u32 sample_rate; |
| /* Sampling rate of the port. |
| * Supported values: |
| * - #AFE_PORT_SAMPLE_RATE_8K |
| * - #AFE_PORT_SAMPLE_RATE_16K |
| */ |
| |
| u16 bit_width; |
| /* Bit width of the sample. |
| * Supported values: 16 |
| */ |
| |
| u16 num_channels; |
| /* Number of channels. |
| * Supported values: 1 to 4 |
| */ |
| |
| u16 slot_number_mapping[4]; |
| /* Specifies the slot number for the each channel in |
| * multi channel scenario. |
| * Supported values: 1 to 32 |
| */ |
| } __packed; |
| |
| /* |
| * This param id is used to configure DIGI MIC interface |
| */ |
| #define AFE_PARAM_ID_DIGI_MIC_CONFIG 0x0001020F |
| /* This version information is used to handle the new |
| * additions to the config interface in future in backward |
| * compatible manner. |
| */ |
| #define AFE_API_VERSION_DIGI_MIC_CONFIG 0x1 |
| |
| /* Enumeration for setting the digital mic configuration |
| * channel_mode parameter to left 0. |
| */ |
| |
| #define AFE_PORT_DIGI_MIC_MODE_LEFT0 0x1 |
| |
| /*Enumeration for setting the digital mic configuration |
| * channel_mode parameter to right 0. |
| */ |
| |
| |
| #define AFE_PORT_DIGI_MIC_MODE_RIGHT0 0x2 |
| |
| /* Enumeration for setting the digital mic configuration |
| * channel_mode parameter to left 1. |
| */ |
| |
| #define AFE_PORT_DIGI_MIC_MODE_LEFT1 0x3 |
| |
| /* Enumeration for setting the digital mic configuration |
| * channel_mode parameter to right 1. |
| */ |
| |
| #define AFE_PORT_DIGI_MIC_MODE_RIGHT1 0x4 |
| |
| /* Enumeration for setting the digital mic configuration |
| * channel_mode parameter to stereo 0. |
| */ |
| #define AFE_PORT_DIGI_MIC_MODE_STEREO0 0x5 |
| |
| /* Enumeration for setting the digital mic configuration |
| * channel_mode parameter to stereo 1. |
| */ |
| |
| |
| #define AFE_PORT_DIGI_MIC_MODE_STEREO1 0x6 |
| |
| /* Enumeration for setting the digital mic configuration |
| * channel_mode parameter to quad. |
| */ |
| |
| #define AFE_PORT_DIGI_MIC_MODE_QUAD 0x7 |
| |
| /* Payload of the #AFE_PARAM_ID_DIGI_MIC_CONFIG command's |
| * (DIGI MIC configuration |
| * parameter). |
| */ |
| struct afe_param_id_digi_mic_cfg { |
| u32 digi_mic_cfg_minor_version; |
| /* Minor version used for tracking the version of the DIGI Mic |
| * configuration interface. |
| * Supported values: #AFE_API_VERSION_DIGI_MIC_CONFIG |
| */ |
| |
| u16 bit_width; |
| /* Bit width of the sample. |
| * Supported values: 16 |
| */ |
| |
| u16 channel_mode; |
| /* Digital mic and multichannel operation. |
| * Supported values: |
| * - #AFE_PORT_DIGI_MIC_MODE_LEFT0 |
| * - #AFE_PORT_DIGI_MIC_MODE_RIGHT0 |
| * - #AFE_PORT_DIGI_MIC_MODE_LEFT1 |
| * - #AFE_PORT_DIGI_MIC_MODE_RIGHT1 |
| * - #AFE_PORT_DIGI_MIC_MODE_STEREO0 |
| * - #AFE_PORT_DIGI_MIC_MODE_STEREO1 |
| * - #AFE_PORT_DIGI_MIC_MODE_QUAD |
| */ |
| |
| u32 sample_rate; |
| /* Sampling rate of the port. |
| * Supported values: |
| * - #AFE_PORT_SAMPLE_RATE_8K |
| * - #AFE_PORT_SAMPLE_RATE_16K |
| * - #AFE_PORT_SAMPLE_RATE_48K |
| */ |
| } __packed; |
| |
| /* This param id is used to configure HDMI interface */ |
| #define AFE_PARAM_ID_HDMI_CONFIG 0x00010210 |
| |
| /* This version information is used to handle the new |
| * additions to the config interface in future in backward |
| * compatible manner. |
| */ |
| #define AFE_API_VERSION_HDMI_CONFIG 0x1 |
| |
| /* Payload of the #AFE_PARAM_ID_HDMI_CONFIG command, |
| * which configures a multichannel HDMI audio interface. |
| */ |
| struct afe_param_id_hdmi_multi_chan_audio_cfg { |
| u32 hdmi_cfg_minor_version; |
| /* Minor version used for tracking the version of the HDMI |
| * configuration interface. |
| * Supported values: #AFE_API_VERSION_HDMI_CONFIG |
| */ |
| |
| u16 datatype; |
| /* data type |
| * Supported values: |
| * - #LINEAR_PCM_DATA |
| * - #NON_LINEAR_DATA |
| * - #LINEAR_PCM_DATA_PACKED_IN_60958 |
| * - #NON_LINEAR_DATA_PACKED_IN_60958 |
| */ |
| |
| u16 channel_allocation; |
| /* HDMI channel allocation information for programming an HDMI |
| * frame. The default is 0 (Stereo). |
| * |
| * This information is defined in the HDMI standard, CEA 861-D |
| * (refer to @xhyperref{S1,[S1]}). The number of channels is also |
| * inferred from this parameter. |
| */ |
| |
| |
| u32 sample_rate; |
| /* Sampling rate of the port. |
| * Supported values: |
| * - #AFE_PORT_SAMPLE_RATE_8K |
| * - #AFE_PORT_SAMPLE_RATE_16K |
| * - #AFE_PORT_SAMPLE_RATE_48K |
| * - #AFE_PORT_SAMPLE_RATE_96K |
| * - 22050, 44100, 176400 for compressed streams |
| */ |
| |
| u16 bit_width; |
| /* Bit width of the sample. |
| * Supported values: 16, 24 |
| */ |
| u16 reserved; |
| /* This field must be set to zero. */ |
| } __packed; |
| |
| /* This param id is used to configure BT or FM(RIVA) interface */ |
| #define AFE_PARAM_ID_INTERNAL_BT_FM_CONFIG 0x00010211 |
| |
| /* This version information is used to handle the new |
| * additions to the config interface in future in backward |
| * compatible manner. |
| */ |
| #define AFE_API_VERSION_INTERNAL_BT_FM_CONFIG 0x1 |
| |
| /* Payload of the #AFE_PARAM_ID_INTERNAL_BT_FM_CONFIG |
| * command's BT voice/BT audio/FM configuration parameter. |
| */ |
| struct afe_param_id_internal_bt_fm_cfg { |
| u32 bt_fm_cfg_minor_version; |
| /* Minor version used for tracking the version of the BT and FM |
| * configuration interface. |
| * Supported values: #AFE_API_VERSION_INTERNAL_BT_FM_CONFIG |
| */ |
| |
| u16 num_channels; |
| /* Number of channels. |
| * Supported values: 1 to 2 |
| */ |
| |
| u16 bit_width; |
| /* Bit width of the sample. |
| * Supported values: 16 |
| */ |
| |
| u32 sample_rate; |
| /* Sampling rate of the port. |
| * Supported values: |
| * - #AFE_PORT_SAMPLE_RATE_8K (only for BTSCO) |
| * - #AFE_PORT_SAMPLE_RATE_16K (only for BTSCO) |
| * - #AFE_PORT_SAMPLE_RATE_48K (FM and A2DP) |
| */ |
| } __packed; |
| |
| /* This param id is used to configure SLIMBUS interface using |
| * shared channel approach. |
| */ |
| |
| |
| #define AFE_PARAM_ID_SLIMBUS_CONFIG 0x00010212 |
| |
| /* This version information is used to handle the new |
| * additions to the config interface in future in backward |
| * compatible manner. |
| */ |
| #define AFE_API_VERSION_SLIMBUS_CONFIG 0x1 |
| |
| /* Enumeration for setting SLIMbus device ID 1. */ |
| #define AFE_SLIMBUS_DEVICE_1 0x0 |
| |
| /* Enumeration for setting SLIMbus device ID 2. */ |
| #define AFE_SLIMBUS_DEVICE_2 0x1 |
| |
| /* Enumeration for setting the SLIMbus data formats. */ |
| #define AFE_SB_DATA_FORMAT_NOT_INDICATED 0x0 |
| |
| /* Enumeration for setting the maximum number of streams per |
| * device. |
| */ |
| |
| #define AFE_PORT_MAX_AUDIO_CHAN_CNT 0x8 |
| |
| /* Payload of the #AFE_PORT_CMD_SLIMBUS_CONFIG command's SLIMbus |
| * port configuration parameter. |
| */ |
| |
| struct afe_param_id_slimbus_cfg { |
| u32 sb_cfg_minor_version; |
| /* Minor version used for tracking the version of the SLIMBUS |
| * configuration interface. |
| * Supported values: #AFE_API_VERSION_SLIMBUS_CONFIG |
| */ |
| |
| u16 slimbus_dev_id; |
| /* SLIMbus hardware device ID, which is required to handle |
| * multiple SLIMbus hardware blocks. |
| * Supported values: - #AFE_SLIMBUS_DEVICE_1 - #AFE_SLIMBUS_DEVICE_2 |
| */ |
| |
| |
| u16 bit_width; |
| /* Bit width of the sample. |
| * Supported values: 16, 24 |
| */ |
| |
| u16 data_format; |
| /* Data format supported by the SLIMbus hardware. The default is |
| * 0 (#AFE_SB_DATA_FORMAT_NOT_INDICATED), which indicates the |
| * hardware does not perform any format conversions before the data |
| * transfer. |
| */ |
| |
| |
| u16 num_channels; |
| /* Number of channels. |
| * Supported values: 1 to #AFE_PORT_MAX_AUDIO_CHAN_CNT |
| */ |
| |
| u8 shared_ch_mapping[AFE_PORT_MAX_AUDIO_CHAN_CNT]; |
| /* Mapping of shared channel IDs (128 to 255) to which the |
| * master port is to be connected. |
| * Shared_channel_mapping[i] represents the shared channel assigned |
| * for audio channel i in multichannel audio data. |
| */ |
| |
| u32 sample_rate; |
| /* Sampling rate of the port. |
| * Supported values: |
| * - #AFE_PORT_SAMPLE_RATE_8K |
| * - #AFE_PORT_SAMPLE_RATE_16K |
| * - #AFE_PORT_SAMPLE_RATE_48K |
| * - #AFE_PORT_SAMPLE_RATE_96K |
| * - #AFE_PORT_SAMPLE_RATE_192K |
| */ |
| } __packed; |
| |
| |
| /* ID of the parameter used by AFE_PARAM_ID_USB_AUDIO_DEV_PARAMS to configure |
| * USB audio device parameter. It should be used with |
| * AFE_MODULE_AUDIO_DEV_INTERFACE |
| */ |
| #define AFE_PARAM_ID_USB_AUDIO_DEV_PARAMS 0x000102A5 |
| |
| |
| /* ID of the parameter used to set the endianness value for the |
| * USB audio device. It should be used with |
| * AFE_MODULE_AUDIO_DEV_INTERFACE |
| */ |
| #define AFE_PARAM_ID_USB_AUDIO_DEV_LPCM_FMT 0x000102AA |
| |
| /* Minor version used for tracking USB audio configuration */ |
| #define AFE_API_MINIOR_VERSION_USB_AUDIO_CONFIG 0x1 |
| |
| /* ID of the parameter used to set the latency mode of the |
| * USB audio device. |
| */ |
| #define AFE_PARAM_ID_PORT_LATENCY_MODE_CONFIG 0x000102B3 |
| |
| /* Minor version used for tracking USB audio latency mode */ |
| #define AFE_API_MINOR_VERSION_USB_AUDIO_LATENCY_MODE 0x1 |
| |
| /* Supported AFE port latency modes */ |
| #define AFE_PORT_DEFAULT_LATENCY_MODE 0x0 |
| #define AFE_PORT_LOW_LATENCY_MODE 0x1 |
| |
| /* Payload of the AFE_PARAM_ID_USB_AUDIO_DEV_PARAMS parameter used by |
| * AFE_MODULE_AUDIO_DEV_INTERFACE. |
| */ |
| struct afe_param_id_usb_audio_dev_params { |
| /* Minor version used for tracking USB audio device parameter. |
| * Supported values: AFE_API_MINIOR_VERSION_USB_AUDIO_CONFIG |
| */ |
| u32 cfg_minor_version; |
| /* Token of actual end USB aduio device */ |
| u32 dev_token; |
| } __packed; |
| |
| struct afe_param_id_usb_audio_dev_lpcm_fmt { |
| /* Minor version used for tracking USB audio device parameter. |
| * Supported values: AFE_API_MINIOR_VERSION_USB_AUDIO_CONFIG |
| */ |
| u32 cfg_minor_version; |
| /* Endianness of actual end USB audio device */ |
| u32 endian; |
| } __packed; |
| |
| struct afe_param_id_usb_audio_dev_latency_mode { |
| /* Minor version used for tracking USB audio device parameter. |
| * Supported values: AFE_API_MINOR_VERSION_USB_AUDIO_LATENCY_MODE |
| */ |
| u32 minor_version; |
| /* latency mode for the USB audio device */ |
| u32 mode; |
| } __packed; |
| |
| |
| |
| /* ID of the parameter used by AFE_PARAM_ID_USB_AUDIO_CONFIG to configure |
| * USB audio interface. It should be used with AFE_MODULE_AUDIO_DEV_INTERFACE |
| */ |
| #define AFE_PARAM_ID_USB_AUDIO_CONFIG 0x000102A4 |
| |
| /* Payload of the AFE_PARAM_ID_USB_AUDIO_CONFIG parameter used by |
| * AFE_MODULE_AUDIO_DEV_INTERFACE. |
| */ |
| struct afe_param_id_usb_audio_cfg { |
| /* Minor version used for tracking USB audio device configuration. |
| * Supported values: AFE_API_MINIOR_VERSION_USB_AUDIO_CONFIG |
| */ |
| u32 cfg_minor_version; |
| /* Sampling rate of the port. |
| * Supported values: |
| * - AFE_PORT_SAMPLE_RATE_8K |
| * - AFE_PORT_SAMPLE_RATE_11025 |
| * - AFE_PORT_SAMPLE_RATE_12K |
| * - AFE_PORT_SAMPLE_RATE_16K |
| * - AFE_PORT_SAMPLE_RATE_22050 |
| * - AFE_PORT_SAMPLE_RATE_24K |
| * - AFE_PORT_SAMPLE_RATE_32K |
| * - AFE_PORT_SAMPLE_RATE_44P1K |
| * - AFE_PORT_SAMPLE_RATE_48K |
| * - AFE_PORT_SAMPLE_RATE_96K |
| * - AFE_PORT_SAMPLE_RATE_192K |
| */ |
| u32 sample_rate; |
| /* Bit width of the sample. |
| * Supported values: 16, 24 |
| */ |
| u16 bit_width; |
| /* Number of channels. |
| * Supported values: 1 and 2 |
| */ |
| u16 num_channels; |
| /* Data format supported by the USB. The supported value is |
| * 0 (#AFE_USB_AUDIO_DATA_FORMAT_LINEAR_PCM). |
| */ |
| u16 data_format; |
| /* this field must be 0 */ |
| u16 reserved; |
| /* device token of actual end USB aduio device */ |
| u32 dev_token; |
| /* endianness of this interface */ |
| u32 endian; |
| /* service interval */ |
| u32 service_interval; |
| } __packed; |
| |
| struct afe_usb_audio_dev_param_command { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| union { |
| struct afe_param_id_usb_audio_dev_params usb_dev; |
| struct afe_param_id_usb_audio_dev_lpcm_fmt lpcm_fmt; |
| struct afe_param_id_usb_audio_dev_latency_mode latency_config; |
| }; |
| } __packed; |
| |
| /* This param id is used to configure Real Time Proxy interface. */ |
| #define AFE_PARAM_ID_RT_PROXY_CONFIG 0x00010213 |
| |
| /* This version information is used to handle the new |
| * additions to the config interface in future in backward |
| * compatible manner. |
| */ |
| #define AFE_API_VERSION_RT_PROXY_CONFIG 0x1 |
| |
| /* Payload of the #AFE_PARAM_ID_RT_PROXY_CONFIG |
| * command (real-time proxy port configuration parameter). |
| */ |
| struct afe_param_id_rt_proxy_port_cfg { |
| u32 rt_proxy_cfg_minor_version; |
| /* Minor version used for tracking the version of rt-proxy |
| * config interface. |
| */ |
| |
| u16 bit_width; |
| /* Bit width of the sample. |
| * Supported values: 16 |
| */ |
| |
| u16 interleaved; |
| /* Specifies whether the data exchanged between the AFE |
| * interface and real-time port is interleaved. |
| * Supported values: - 0 -- Non-interleaved (samples from each |
| * channel are contiguous in the buffer) - 1 -- Interleaved |
| * (corresponding samples from each input channel are interleaved |
| * within the buffer) |
| */ |
| |
| |
| u16 frame_size; |
| /* Size of the frames that are used for PCM exchanges with this |
| * port. |
| * Supported values: > 0, in bytes |
| * For example, 5 ms buffers of 16 bits and 16 kHz stereo samples |
| * is 5 ms * 16 samples/ms * 2 bytes/sample * 2 channels = 320 |
| * bytes. |
| */ |
| u16 jitter_allowance; |
| /* Configures the amount of jitter that the port will allow. |
| * Supported values: > 0 |
| * For example, if +/-10 ms of jitter is anticipated in the timing |
| * of sending frames to the port, and the configuration is 16 kHz |
| * mono with 16-bit samples, this field is 10 ms * 16 samples/ms * 2 |
| * bytes/sample = 320. |
| */ |
| |
| u16 low_water_mark; |
| /* Low watermark in bytes (including all channels). |
| * Supported values: |
| * - 0 -- Do not send any low watermark events |
| * - > 0 -- Low watermark for triggering an event |
| * If the number of bytes in an internal circular buffer is lower |
| * than this low_water_mark parameter, a LOW_WATER_MARK event is |
| * sent to applications (via the #AFE_EVENT_RT_PROXY_PORT_STATUS |
| * event). |
| * Use of watermark events is optional for debugging purposes. |
| */ |
| |
| u16 high_water_mark; |
| /* High watermark in bytes (including all channels). |
| * Supported values: |
| * - 0 -- Do not send any high watermark events |
| * - > 0 -- High watermark for triggering an event |
| * If the number of bytes in an internal circular buffer exceeds |
| * TOTAL_CIRC_BUF_SIZE minus high_water_mark, a high watermark event |
| * is sent to applications (via the #AFE_EVENT_RT_PROXY_PORT_STATUS |
| * event). |
| * The use of watermark events is optional and for debugging |
| * purposes. |
| */ |
| |
| |
| u32 sample_rate; |
| /* Sampling rate of the port. |
| * Supported values: |
| * - #AFE_PORT_SAMPLE_RATE_8K |
| * - #AFE_PORT_SAMPLE_RATE_16K |
| * - #AFE_PORT_SAMPLE_RATE_48K |
| */ |
| |
| u16 num_channels; |
| /* Number of channels. |
| * Supported values: 1 to #AFE_PORT_MAX_AUDIO_CHAN_CNT |
| */ |
| |
| u16 reserved; |
| /* For 32 bit alignment. */ |
| } __packed; |
| |
| |
| /* This param id is used to configure the Pseudoport interface */ |
| |
| #define AFE_PARAM_ID_PSEUDO_PORT_CONFIG 0x00010219 |
| |
| /* Version information used to handle future additions to the configuration |
| * interface (for backward compatibility). |
| */ |
| #define AFE_API_VERSION_PSEUDO_PORT_CONFIG 0x1 |
| |
| /* Enumeration for setting the timing_mode parameter to faster than real |
| * time. |
| */ |
| #define AFE_PSEUDOPORT_TIMING_MODE_FTRT 0x0 |
| |
| /* Enumeration for setting the timing_mode parameter to real time using |
| * timers. |
| */ |
| #define AFE_PSEUDOPORT_TIMING_MODE_TIMER 0x1 |
| |
| /* Payload of the AFE_PARAM_ID_PSEUDO_PORT_CONFIG parameter used by |
| * AFE_MODULE_AUDIO_DEV_INTERFACE. |
| */ |
| struct afe_param_id_pseudo_port_cfg { |
| u32 pseud_port_cfg_minor_version; |
| /* |
| * Minor version used for tracking the version of the pseudoport |
| * configuration interface. |
| */ |
| |
| u16 bit_width; |
| /* Bit width of the sample at values 16, 24 */ |
| |
| u16 num_channels; |
| /* Number of channels at values 1 to 8 */ |
| |
| u16 data_format; |
| /* Non-linear data format supported by the pseudoport (for future use). |
| * At values #AFE_LINEAR_PCM_DATA |
| */ |
| |
| u16 timing_mode; |
| /* Indicates whether the pseudoport synchronizes to the clock or |
| * operates faster than real time. |
| * at values |
| * - #AFE_PSEUDOPORT_TIMING_MODE_FTRT |
| * - #AFE_PSEUDOPORT_TIMING_MODE_TIMER @tablebulletend |
| */ |
| |
| u32 sample_rate; |
| /* Sample rate at which the pseudoport will run. |
| * at values |
| * - #AFE_PORT_SAMPLE_RATE_8K |
| * - #AFE_PORT_SAMPLE_RATE_32K |
| * - #AFE_PORT_SAMPLE_RATE_48K |
| * - #AFE_PORT_SAMPLE_RATE_96K |
| * - #AFE_PORT_SAMPLE_RATE_192K @tablebulletend |
| */ |
| } __packed; |
| |
| #define AFE_PARAM_ID_TDM_CONFIG 0x0001029D |
| |
| #define AFE_API_VERSION_TDM_CONFIG 1 |
| |
| #define AFE_PORT_TDM_SHORT_SYNC_BIT_MODE 0 |
| #define AFE_PORT_TDM_LONG_SYNC_MODE 1 |
| #define AFE_PORT_TDM_SHORT_SYNC_SLOT_MODE 2 |
| |
| #define AFE_PORT_TDM_SYNC_SRC_EXTERNAL 0 |
| #define AFE_PORT_TDM_SYNC_SRC_INTERNAL 1 |
| |
| #define AFE_PORT_TDM_CTRL_DATA_OE_DISABLE 0 |
| #define AFE_PORT_TDM_CTRL_DATA_OE_ENABLE 1 |
| |
| #define AFE_PORT_TDM_SYNC_NORMAL 0 |
| #define AFE_PORT_TDM_SYNC_INVERT 1 |
| |
| #define AFE_PORT_TDM_DATA_DELAY_0_BCLK_CYCLE 0 |
| #define AFE_PORT_TDM_DATA_DELAY_1_BCLK_CYCLE 1 |
| #define AFE_PORT_TDM_DATA_DELAY_2_BCLK_CYCLE 2 |
| |
| /* Payload of the AFE_PARAM_ID_TDM_CONFIG parameter used by |
| * AFE_MODULE_AUDIO_DEV_INTERFACE. |
| */ |
| struct afe_param_id_tdm_cfg { |
| u32 tdm_cfg_minor_version; |
| /* < Minor version used to track TDM configuration. |
| * @values #AFE_API_VERSION_TDM_CONFIG |
| */ |
| |
| u32 num_channels; |
| /* < Number of enabled slots for TDM frame. |
| * @values 1 to 8 |
| */ |
| |
| u32 sample_rate; |
| /* < Sampling rate of the port. |
| * @values |
| * - #AFE_PORT_SAMPLE_RATE_8K |
| * - #AFE_PORT_SAMPLE_RATE_16K |
| * - #AFE_PORT_SAMPLE_RATE_24K |
| * - #AFE_PORT_SAMPLE_RATE_32K |
| * - #AFE_PORT_SAMPLE_RATE_48K |
| * - #AFE_PORT_SAMPLE_RATE_176P4K |
| * - #AFE_PORT_SAMPLE_RATE_352P8K @tablebulletend |
| */ |
| |
| u32 bit_width; |
| /* < Bit width of the sample. |
| * @values 16, 24 |
| */ |
| |
| u16 data_format; |
| /* < Data format: linear ,compressed, generic compresssed |
| * @values |
| * - #AFE_LINEAR_PCM_DATA |
| * - #AFE_NON_LINEAR_DATA |
| * - #AFE_GENERIC_COMPRESSED |
| */ |
| |
| u16 sync_mode; |
| /* < TDM synchronization setting. |
| * @values (short, long, slot) sync mode |
| * - #AFE_PORT_TDM_SHORT_SYNC_BIT_MODE |
| * - #AFE_PORT_TDM_LONG_SYNC_MODE |
| * - #AFE_PORT_TDM_SHORT_SYNC_SLOT_MODE @tablebulletend |
| */ |
| |
| u16 sync_src; |
| /* < Synchronization source. |
| * @values |
| * - #AFE_PORT_TDM_SYNC_SRC_EXTERNAL |
| * - #AFE_PORT_TDM_SYNC_SRC_INTERNAL @tablebulletend |
| */ |
| |
| u16 nslots_per_frame; |
| /* < Number of slots per frame. Typical : 1, 2, 4, 8, 16, 32. |
| * @values 1 - 32 |
| */ |
| |
| u16 ctrl_data_out_enable; |
| /* < Specifies whether the TDM block shares the data-out signal to the |
| * drive with other masters. |
| * @values |
| * - #AFE_PORT_TDM_CTRL_DATA_OE_DISABLE |
| * - #AFE_PORT_TDM_CTRL_DATA_OE_ENABLE @tablebulletend |
| */ |
| |
| u16 ctrl_invert_sync_pulse; |
| /* < Specifies whether to invert the sync or not. |
| * @values |
| * - #AFE_PORT_TDM_SYNC_NORMAL |
| * - #AFE_PORT_TDM_SYNC_INVERT @tablebulletend |
| */ |
| |
| u16 ctrl_sync_data_delay; |
| /* < Specifies the number of bit clock to delay data with respect to |
| * sync edge. |
| * @values |
| * - #AFE_PORT_TDM_DATA_DELAY_0_BCLK_CYCLE |
| * - #AFE_PORT_TDM_DATA_DELAY_1_BCLK_CYCLE |
| * - #AFE_PORT_TDM_DATA_DELAY_2_BCLK_CYCLE @tablebulletend |
| */ |
| |
| u16 slot_width; |
| /* < Slot width of the slot in a TDM frame. (slot_width >= bit_width) |
| * have to be satisfied. |
| * @values 16, 24, 32 |
| */ |
| |
| u32 slot_mask; |
| /* < Position of active slots. When that bit is set, |
| * that paricular slot is active. |
| * Number of active slots can be inferred by number of |
| * bits set in the mask. Only 8 individual bits can be enabled. |
| * Bits 0..31 corresponding to slot 0..31 |
| * @values 1 to 2^32 - 1 |
| */ |
| } __packed; |
| |
| /* ID of Time Divsion Multiplexing (TDM) module, |
| * which is used for configuring the AFE TDM. |
| * |
| * This module supports following parameter IDs: |
| * - #AFE_PORT_TDM_SLOT_CONFIG |
| * |
| * To configure the TDM interface, the client must use the |
| * #AFE_PORT_CMD_SET_PARAM command, and fill the module ID with the |
| * respective parameter IDs as listed above. |
| */ |
| |
| #define AFE_MODULE_TDM 0x0001028A |
| |
| /* ID of the parameter used by #AFE_MODULE_TDM to configure |
| * the TDM slot mapping. #AFE_PORT_CMD_SET_PARAM can use this parameter ID. |
| */ |
| #define AFE_PARAM_ID_PORT_SLOT_MAPPING_CONFIG 0x00010297 |
| |
| /* Version information used to handle future additions to slot mapping |
| * configuration (for backward compatibility). |
| */ |
| #define AFE_API_VERSION_SLOT_MAPPING_CONFIG 0x1 |
| |
| /* Data align type */ |
| #define AFE_SLOT_MAPPING_DATA_ALIGN_MSB 0 |
| #define AFE_SLOT_MAPPING_DATA_ALIGN_LSB 1 |
| |
| #define AFE_SLOT_MAPPING_OFFSET_INVALID 0xFFFF |
| |
| /* Payload of the AFE_PARAM_ID_PORT_SLOT_MAPPING_CONFIG |
| * command's TDM configuration parameter. |
| */ |
| struct afe_param_id_slot_mapping_cfg { |
| u32 minor_version; |
| /* < Minor version used for tracking TDM slot configuration. |
| * @values #AFE_API_VERSION_TDM_SLOT_CONFIG |
| */ |
| |
| u16 num_channel; |
| /* < number of channel of the audio sample. |
| * @values 1, 2, 4, 6, 8 @tablebulletend |
| */ |
| |
| u16 bitwidth; |
| /* < Slot bit width for each channel |
| * @values 16, 24, 32 |
| */ |
| |
| u32 data_align_type; |
| /* < indicate how data packed from slot_offset for 32 slot bit width |
| * in case of sample bit width is 24. |
| * @values |
| * #AFE_SLOT_MAPPING_DATA_ALIGN_MSB |
| * #AFE_SLOT_MAPPING_DATA_ALIGN_LSB |
| */ |
| |
| u16 offset[AFE_PORT_MAX_AUDIO_CHAN_CNT]; |
| /* < Array of the slot mapping start offset in bytes for this frame. |
| * The bytes is counted from 0. The 0 is mapped to the 1st byte |
| * in or out of the digital serial data line this sub-frame belong to. |
| * slot_offset[] setting is per-channel based. |
| * The max num of channel supported is 8. |
| * The valid offset value must always be continuly placed in from |
| * index 0. |
| * Set offset as AFE_SLOT_MAPPING_OFFSET_INVALID for not used arrays. |
| * If "slot_bitwidth_per_channel" is 32 and "sample_bitwidth" is 24, |
| * "data_align_type" is used to indicate how 24 bit sample data in |
| * aligning with 32 bit slot width per-channel. |
| * @values, in byte |
| */ |
| } __packed; |
| |
| /* ID of the parameter used by #AFE_MODULE_TDM to configure |
| * the customer TDM header. #AFE_PORT_CMD_SET_PARAM can use this parameter ID. |
| */ |
| #define AFE_PARAM_ID_CUSTOM_TDM_HEADER_CONFIG 0x00010298 |
| |
| /* Version information used to handle future additions to custom TDM header |
| * configuration (for backward compatibility). |
| */ |
| #define AFE_API_VERSION_CUSTOM_TDM_HEADER_CONFIG 0x1 |
| |
| #define AFE_CUSTOM_TDM_HEADER_TYPE_INVALID 0x0 |
| #define AFE_CUSTOM_TDM_HEADER_TYPE_DEFAULT 0x1 |
| #define AFE_CUSTOM_TDM_HEADER_TYPE_ENTERTAINMENT_MOST 0x2 |
| |
| #define AFE_CUSTOM_TDM_HEADER_MAX_CNT 0x8 |
| |
| /* Payload of the AFE_PARAM_ID_CUSTOM_TDM_HEADER_CONFIG parameter ID */ |
| struct afe_param_id_custom_tdm_header_cfg { |
| u32 minor_version; |
| /* < Minor version used for tracking custom TDM header configuration. |
| * @values #AFE_API_VERSION_CUSTOM_TDM_HEADER_CONFIG |
| */ |
| |
| u16 start_offset; |
| /* < the slot mapping start offset in bytes from this sub-frame |
| * The bytes is counted from 0. The 0 is mapped to the 1st byte in or |
| * out of the digital serial data line this sub-frame belong to. |
| * @values, in byte, |
| * supported values are 0, 4, 8 |
| */ |
| |
| u16 header_width; |
| /* < the header width per-frame followed. |
| * 2 bytes for MOST/TDM case |
| * @values, in byte |
| * supported value is 2 |
| */ |
| |
| u16 header_type; |
| /* < Indicate what kind of custom TDM header it is. |
| * @values #AFE_CUSTOM_TDM_HEADER_TYPE_INVALID = 0 |
| * #AFE_CUSTOM_TDM_HEADER_TYPE_DEFAULT = 1 (for AAN channel per MOST) |
| * #AFE_CUSTOM_TDM_HEADER_TYPE_ENTERTAINMENT_MOST = 2 |
| * (for entertainment channel, which will overwrite |
| * AFE_API_VERSION_TDM_SAD_HEADER_TYPE_DEFAULT per MOST) |
| */ |
| |
| u16 num_frame_repeat; |
| /* < num of header followed. |
| * @values, supported value is 8 |
| */ |
| u16 header[AFE_CUSTOM_TDM_HEADER_MAX_CNT]; |
| /* < SAD header for MOST/TDM case is followed as payload as below. |
| * The size of followed SAD header in bytes is num_of_frame_repeat * |
| * header_width_per_frame, which is 2 * 8 = 16 bytes here. |
| * the supported payload format is in uint16_t as below |
| * uint16_t header0; SyncHi 0x3C Info[4] - CodecType -> 0x3C00 |
| * uint16_t header1; SyncLo 0xB2 Info[5] - SampleWidth -> 0xB218 |
| * uint16_t header2; DTCP Info Info[6] - unused -> 0x0 |
| * uint16_t header3; Extension Info[7] - ASAD-Value -> 0xC0 |
| * uint16_t header4; Reserved Info[0] - Num of bytes following -> 0x7 |
| * uint16_t header5; Reserved Info[1] - Media Type -> 0x0 |
| * uint16_t header6; Reserved Info[2] - Bitrate[kbps] - High Byte -> 0x0 |
| * uint16_t header7; Reserved Info[3] - Bitrate[kbps] - Low Byte -> 0x0 |
| */ |
| } __packed; |
| |
| struct afe_slot_mapping_config_command { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_param_id_slot_mapping_cfg slot_mapping; |
| } __packed; |
| |
| struct afe_custom_tdm_header_config_command { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_param_id_custom_tdm_header_cfg custom_tdm_header; |
| } __packed; |
| |
| struct afe_tdm_port_config { |
| struct afe_param_id_tdm_cfg tdm; |
| struct afe_param_id_slot_mapping_cfg slot_mapping; |
| struct afe_param_id_custom_tdm_header_cfg custom_tdm_header; |
| } __packed; |
| |
| #define AFE_PARAM_ID_DEVICE_HW_DELAY 0x00010243 |
| #define AFE_API_VERSION_DEVICE_HW_DELAY 0x1 |
| |
| struct afe_param_id_device_hw_delay_cfg { |
| uint32_t device_hw_delay_minor_version; |
| uint32_t delay_in_us; |
| } __packed; |
| |
| #define AFE_PARAM_ID_SET_TOPOLOGY 0x0001025A |
| #define AFE_API_VERSION_TOPOLOGY_V1 0x1 |
| |
| struct afe_param_id_set_topology_cfg { |
| /* |
| * Minor version used for tracking afe topology id configuration. |
| * @values #AFE_API_VERSION_TOPOLOGY_V1 |
| */ |
| u32 minor_version; |
| /* |
| * Id of the topology for the afe session. |
| * @values Any valid AFE topology ID |
| */ |
| u32 topology_id; |
| } __packed; |
| |
| #define MAX_ABR_LEVELS 5 |
| |
| struct afe_bit_rate_level_map_t { |
| /* |
| * Key value pair for link quality level to bitrate |
| * mapping in AFE |
| */ |
| uint32_t link_quality_level; |
| uint32_t bitrate; |
| } __packed; |
| |
| struct afe_quality_level_to_bitrate_info { |
| /* |
| * Number of quality levels being mapped. |
| * This will be equal to the size of mapping table. |
| */ |
| uint32_t num_levels; |
| /* |
| * Quality level to bitrate mapping table |
| */ |
| struct afe_bit_rate_level_map_t bit_rate_level_map[MAX_ABR_LEVELS]; |
| } __packed; |
| |
| struct afe_imc_dec_enc_info { |
| /* |
| * Decoder to encoder communication direction. |
| * Transmit = 0 / Receive = 1 |
| */ |
| uint32_t direction; |
| /* |
| * Enable / disable IMC between decoder and encoder |
| */ |
| uint32_t enable; |
| /* |
| * Purpose of IMC being set up between decoder and encoder. |
| * Param ID defined for link quality feedback in LPASS will |
| * be the default value sent as purpose. |
| * Supported values: |
| * AFE_ENCDEC_PURPOSE_ID_BT_INFO |
| */ |
| uint32_t purpose; |
| /* |
| * Unique communication instance ID. |
| * Data type a2dp_abr_instance used to set instance ID. |
| * purpose and comm_instance together form the actual key |
| * used in IMC registration, which must be the same for |
| * encoder and decoder for which IMC is being set up. |
| */ |
| uint32_t comm_instance; |
| } __packed; |
| |
| struct afe_abr_dec_cfg_t { |
| struct afe_imc_dec_enc_info imc_info; |
| } __packed; |
| |
| struct afe_abr_enc_cfg_t { |
| /* |
| * Link quality level to bitrate mapping info sent to DSP. |
| */ |
| struct afe_quality_level_to_bitrate_info mapping_info; |
| /* |
| * Information to set up IMC between decoder and encoder. |
| */ |
| struct afe_imc_dec_enc_info imc_info; |
| } __packed; |
| |
| #define AFE_PARAM_ID_APTX_SYNC_MODE 0x00013205 |
| |
| struct afe_param_id_aptx_sync_mode { |
| /* |
| * sync mode: 0x0 = stereo sync mode (default) |
| * 0x01 = dual mono sync mode |
| * 0x02 = dual mono with no sync on either L or R |
| */ |
| uint32_t sync_mode; |
| } __packed; |
| |
| /* |
| * Generic encoder module ID. |
| * This module supports the following parameter IDs: |
| * #AVS_ENCODER_PARAM_ID_ENC_FMT_ID (cannot be set run time) |
| * #AVS_ENCODER_PARAM_ID_ENC_CFG_BLK (may be set run time) |
| * #AVS_ENCODER_PARAM_ID_ENC_BITRATE (may be set run time) |
| * #AVS_ENCODER_PARAM_ID_PACKETIZER_ID (cannot be set run time) |
| * Opcode - AVS_MODULE_ID_ENCODER |
| * AFE Command AFE_PORT_CMD_SET_PARAM_V2 supports this module ID. |
| */ |
| #define AFE_MODULE_ID_ENCODER 0x00013229 |
| |
| /* Macro for defining the packetizer ID: COP. */ |
| #define AFE_MODULE_ID_PACKETIZER_COP 0x0001322A |
| |
| /* |
| * Packetizer type parameter for the #AVS_MODULE_ID_ENCODER module. |
| * This parameter cannot be set runtime. |
| */ |
| #define AFE_ENCODER_PARAM_ID_PACKETIZER_ID 0x0001322E |
| |
| /* |
| * Encoder config block parameter for the #AVS_MODULE_ID_ENCODER module. |
| * This parameter may be set runtime. |
| */ |
| #define AFE_ENCODER_PARAM_ID_ENC_CFG_BLK 0x0001322C |
| |
| /* |
| * Encoder format ID parameter for the #AVS_MODULE_ID_ENCODER module. |
| * This parameter cannot be set runtime. |
| */ |
| #define AFE_ENCODER_PARAM_ID_ENC_FMT_ID 0x0001322B |
| |
| /* |
| * Encoder scrambler parameter for the #AVS_MODULE_ID_ENCODER module. |
| * This parameter cannot be set runtime. |
| */ |
| #define AFE_ENCODER_PARAM_ID_ENABLE_SCRAMBLING 0x0001323C |
| |
| /* |
| * Link quality level to bitrate mapping info sent to AFE Encoder. |
| * This parameter may be set runtime. |
| */ |
| #define AFE_ENCODER_PARAM_ID_BIT_RATE_LEVEL_MAP 0x000132E1 |
| |
| /* |
| * Parameter to set up Inter Module Communication (IMC) between |
| * AFE Decoder and Encoder. |
| * This parameter may be set runtime. |
| */ |
| #define AFE_ENCDEC_PARAM_ID_DEC_TO_ENC_COMMUNICATION 0x0001323D |
| |
| /* |
| * Purpose of IMC set up between encoder and decoder. |
| * Communication instance and purpose together form the |
| * actual key used for IMC registration. |
| */ |
| #define AFE_ENCDEC_PURPOSE_ID_BT_INFO 0x000132E2 |
| |
| #define AFE_MODULE_ID_DECODER 0x00013231 |
| |
| /* |
| * Macro for defining the depacketizer ID: COP. |
| */ |
| #define AFE_MODULE_ID_DEPACKETIZER_COP 0x00013233 |
| |
| /* |
| * Depacketizer type parameter for the #AVS_MODULE_ID_DECODER module. |
| * This parameter cannot be set runtime. |
| */ |
| #define AFE_DECODER_PARAM_ID_DEPACKETIZER_ID 0x00013235 |
| |
| /* |
| * Data format to send compressed data |
| * is transmitted/received over Slimbus lines. |
| */ |
| #define AFE_SB_DATA_FORMAT_GENERIC_COMPRESSED 0x3 |
| |
| /* |
| * ID for AFE port module. This will be used to define port properties. |
| * This module supports following parameter IDs: |
| * #AFE_PARAM_ID_PORT_MEDIA_TYPE |
| * To configure the port property, the client must use the |
| * #AFE_PORT_CMD_SET_PARAM_V2 command, |
| * and fill the module ID with the respective parameter IDs as listed above. |
| * @apr_hdr_fields |
| * Opcode -- AFE_MODULE_PORT |
| */ |
| #define AFE_MODULE_PORT 0x000102a6 |
| |
| /* |
| * ID of the parameter used by #AFE_MODULE_PORT to set the port media type. |
| * parameter ID is currently supported using#AFE_PORT_CMD_SET_PARAM_V2 command. |
| */ |
| #define AFE_PARAM_ID_PORT_MEDIA_TYPE 0x000102a7 |
| |
| /* |
| * Macros for defining the "data_format" field in the |
| * #AFE_PARAM_ID_PORT_MEDIA_TYPE |
| */ |
| #define AFE_PORT_DATA_FORMAT_PCM 0x0 |
| #define AFE_PORT_DATA_FORMAT_GENERIC_COMPRESSED 0x1 |
| |
| /* |
| * Macro for defining the "minor_version" field in the |
| * #AFE_PARAM_ID_PORT_MEDIA_TYPE |
| */ |
| #define AFE_API_VERSION_PORT_MEDIA_TYPE 0x1 |
| |
| #define ASM_MEDIA_FMT_NONE 0x0 |
| |
| /* |
| * Media format ID for SBC encode configuration. |
| * @par SBC encode configuration (asm_sbc_enc_cfg_t) |
| * @table{weak__asm__sbc__enc__cfg__t} |
| */ |
| #define ASM_MEDIA_FMT_SBC 0x00010BF2 |
| |
| /* SBC channel Mono mode.*/ |
| #define ASM_MEDIA_FMT_SBC_CHANNEL_MODE_MONO 1 |
| |
| /* SBC channel Stereo mode. */ |
| #define ASM_MEDIA_FMT_SBC_CHANNEL_MODE_STEREO 2 |
| |
| /* SBC channel Dual Mono mode. */ |
| #define ASM_MEDIA_FMT_SBC_CHANNEL_MODE_DUAL_MONO 8 |
| |
| /* SBC channel Joint Stereo mode. */ |
| #define ASM_MEDIA_FMT_SBC_CHANNEL_MODE_JOINT_STEREO 9 |
| |
| /* SBC bit allocation method = loudness. */ |
| #define ASM_MEDIA_FMT_SBC_ALLOCATION_METHOD_LOUDNESS 0 |
| |
| /* SBC bit allocation method = SNR. */ |
| #define ASM_MEDIA_FMT_SBC_ALLOCATION_METHOD_SNR 1 |
| |
| |
| /* |
| * Payload of the SBC encoder configuration parameters in the |
| * #ASM_MEDIA_FMT_SBC media format. |
| */ |
| struct asm_sbc_enc_cfg_t { |
| /* |
| * Number of subbands. |
| * @values 4, 8 |
| */ |
| uint32_t num_subbands; |
| |
| /* |
| * Size of the encoded block in samples. |
| * @values 4, 8, 12, 16 |
| */ |
| uint32_t blk_len; |
| |
| /* |
| * Mode used to allocate bits between channels. |
| * @values |
| * 0 (Native mode) |
| * #ASM_MEDIA_FMT_SBC_CHANNEL_MODE_MONO |
| * #ASM_MEDIA_FMT_SBC_CHANNEL_MODE_STEREO |
| * #ASM_MEDIA_FMT_SBC_CHANNEL_MODE_DUAL_MONO |
| * #ASM_MEDIA_FMT_SBC_CHANNEL_MODE_JOINT_STEREO |
| * Native mode indicates that encoding must be performed with the number |
| * of channels at the input. |
| * If postprocessing outputs one-channel data, Mono mode is used. If |
| * postprocessing outputs two-channel data, Stereo mode is used. |
| * The number of channels must not change during encoding. |
| */ |
| uint32_t channel_mode; |
| |
| /* |
| * Encoder bit allocation method. |
| * @values |
| * #ASM_MEDIA_FMT_SBC_ALLOCATION_METHOD_LOUDNESS |
| * #ASM_MEDIA_FMT_SBC_ALLOCATION_METHOD_SNR @tablebulletend |
| */ |
| uint32_t alloc_method; |
| |
| /* |
| * Number of encoded bits per second. |
| * @values |
| * Mono channel -- Maximum of 320 kbps |
| * Stereo channel -- Maximum of 512 kbps @tablebulletend |
| */ |
| uint32_t bit_rate; |
| |
| /* |
| * Number of samples per second. |
| * @values 0 (Native mode), 16000, 32000, 44100, 48000 Hz |
| * Native mode indicates that encoding must be performed with the |
| * sampling rate at the input. |
| * The sampling rate must not change during encoding. |
| */ |
| uint32_t sample_rate; |
| }; |
| |
| #define ASM_MEDIA_FMT_AAC_AOT_LC 2 |
| #define ASM_MEDIA_FMT_AAC_AOT_SBR 5 |
| #define ASM_MEDIA_FMT_AAC_AOT_PS 29 |
| #define ASM_MEDIA_FMT_AAC_FORMAT_FLAG_ADTS 0 |
| #define ASM_MEDIA_FMT_AAC_FORMAT_FLAG_RAW 3 |
| |
| struct asm_aac_enc_cfg_v2_t { |
| |
| /* Encoding rate in bits per second.*/ |
| uint32_t bit_rate; |
| |
| /* |
| * Encoding mode. |
| * Supported values: |
| * #ASM_MEDIA_FMT_AAC_AOT_LC |
| * #ASM_MEDIA_FMT_AAC_AOT_SBR |
| * #ASM_MEDIA_FMT_AAC_AOT_PS |
| */ |
| uint32_t enc_mode; |
| |
| /* |
| * AAC format flag. |
| * Supported values: |
| * #ASM_MEDIA_FMT_AAC_FORMAT_FLAG_ADTS |
| * #ASM_MEDIA_FMT_AAC_FORMAT_FLAG_RAW |
| */ |
| uint16_t aac_fmt_flag; |
| |
| /* |
| * Number of channels to encode. |
| * Supported values: |
| * 0 - Native mode |
| * 1 - Mono |
| * 2 - Stereo |
| * Other values are not supported. |
| * @note1hang The eAAC+ encoder mode supports only stereo. |
| * Native mode indicates that encoding must be performed with the |
| * number of channels at the input. |
| * The number of channels must not change during encoding. |
| */ |
| uint16_t channel_cfg; |
| |
| /* |
| * Number of samples per second. |
| * Supported values: - 0 -- Native mode - For other values, |
| * Native mode indicates that encoding must be performed with the |
| * sampling rate at the input. |
| * The sampling rate must not change during encoding. |
| */ |
| uint32_t sample_rate; |
| } __packed; |
| |
| /* FMT ID for apt-X Classic */ |
| #define ASM_MEDIA_FMT_APTX 0x000131ff |
| |
| /* FMT ID for apt-X HD */ |
| #define ASM_MEDIA_FMT_APTX_HD 0x00013200 |
| |
| #define PCM_CHANNEL_L 1 |
| #define PCM_CHANNEL_R 2 |
| #define PCM_CHANNEL_C 3 |
| |
| struct asm_custom_enc_cfg_t { |
| uint32_t sample_rate; |
| /* Mono or stereo */ |
| uint16_t num_channels; |
| uint16_t reserved; |
| /* num_ch == 1, then PCM_CHANNEL_C, |
| * num_ch == 2, then {PCM_CHANNEL_L, PCM_CHANNEL_R} |
| */ |
| uint8_t channel_mapping[8]; |
| uint32_t custom_size; |
| } __packed; |
| |
| struct asm_aptx_v2_enc_cfg_ext_t { |
| /* |
| * sync mode: 0x0 = stereo sync mode (default) |
| * 0x01 = dual mono sync mode |
| * 0x02 = dual mono with no sync on either L or R |
| */ |
| uint32_t sync_mode; |
| } __packed; |
| |
| struct asm_aptx_enc_cfg_t { |
| struct asm_custom_enc_cfg_t custom_cfg; |
| struct asm_aptx_v2_enc_cfg_ext_t aptx_v2_cfg; |
| } __packed; |
| |
| #define ASM_MEDIA_FMT_CELT 0x00013221 |
| struct asm_celt_specific_enc_cfg_t { |
| /* |
| * Bit rate used for encoding. |
| * This is used to calculate the upper threshold |
| * for bytes per frame if vbr_flag is 1. |
| * Or else, this will be used as a regular constant |
| * bit rate for encoder output. |
| * @Range : 32000 to 1536000 |
| * @Default: 128 |
| */ |
| uint32_t bit_rate; |
| /* |
| * Frame size used for encoding. |
| * @Range : 64, 128, 256, 512 |
| * @Default: 256 |
| */ |
| uint16_t frame_size; |
| /* |
| * complexity of algorithm. |
| * @Range : 0-10 |
| * @Default: 3 |
| */ |
| uint16_t complexity; |
| /* |
| * Switch variable for prediction feature. |
| * Used to choose between the level of interframe |
| * predictions allowed while encoding. |
| * @Range: |
| * 0: Independent Frames. |
| * 1: Short Term interframe prediction allowed. |
| * 2: Long term prediction allowed. |
| * @Default: 2 |
| */ |
| uint16_t prediction_mode; |
| /* |
| * Variable Bit Rate flag. |
| * @Default: 0 |
| */ |
| uint16_t vbr_flag; |
| } __packed; |
| |
| struct asm_celt_enc_cfg_t { |
| struct asm_custom_enc_cfg_t custom_config; |
| struct asm_celt_specific_enc_cfg_t celt_specific_config; |
| } __packed; |
| |
| #define ASM_MEDIA_FMT_LDAC 0x00013224 |
| struct asm_ldac_specific_enc_cfg_t { |
| /* |
| * This is used to calculate the encoder output |
| * bytes per frame (i.e. bytes per packet). |
| * Bit rate also configures the EQMID. |
| * The min bit rate 303000 bps is calculated for |
| * 44.1 kHz and 88.2 KHz sampling frequencies with |
| * Mobile use Quality. |
| * The max bit rate of 990000 bps is calculated for |
| * 96kHz and 48 KHz with High Quality |
| * @Range(in bits per second) |
| * 303000 for Mobile use Quality |
| * 606000 for standard Quality |
| * 909000 for High Quality |
| */ |
| uint32_t bit_rate; |
| /* |
| * The channel setting information for LDAC specification |
| * of Bluetooth A2DP which is determined by SRC and SNK |
| * devices in Bluetooth transmission. |
| * @Range: |
| * 0 for native mode |
| * 4 for mono |
| * 2 for dual channel |
| * 1 for stereo |
| */ |
| uint16_t channel_mode; |
| /* |
| * Maximum Transmission Unit (MTU). |
| * The minimum MTU that a L2CAP implementation for LDAC shall |
| * support is 679 bytes, because LDAC is optimized with 2-DH5 |
| * packet as its target. |
| * @Range : 679 |
| * @Default: 679 for LDACBT_MTU_2DH5 |
| */ |
| uint16_t mtu; |
| } __packed; |
| |
| struct asm_ldac_enc_cfg_t { |
| struct asm_custom_enc_cfg_t custom_config; |
| struct asm_ldac_specific_enc_cfg_t ldac_specific_config; |
| struct afe_abr_enc_cfg_t abr_config; |
| } __packed; |
| |
| struct afe_enc_fmt_id_param_t { |
| /* |
| * Supported values: |
| * #ASM_MEDIA_FMT_SBC |
| * #ASM_MEDIA_FMT_AAC_V2 |
| * Any OpenDSP supported values |
| */ |
| uint32_t fmt_id; |
| } __packed; |
| |
| struct afe_port_media_type_t { |
| /* |
| * Minor version |
| * @values #AFE_API_VERSION_PORT_MEDIA_TYPE. |
| */ |
| uint32_t minor_version; |
| |
| /* |
| * Sampling rate of the port. |
| * @values |
| * #AFE_PORT_SAMPLE_RATE_8K |
| * #AFE_PORT_SAMPLE_RATE_11_025K |
| * #AFE_PORT_SAMPLE_RATE_12K |
| * #AFE_PORT_SAMPLE_RATE_16K |
| * #AFE_PORT_SAMPLE_RATE_22_05K |
| * #AFE_PORT_SAMPLE_RATE_24K |
| * #AFE_PORT_SAMPLE_RATE_32K |
| * #AFE_PORT_SAMPLE_RATE_44_1K |
| * #AFE_PORT_SAMPLE_RATE_48K |
| * #AFE_PORT_SAMPLE_RATE_88_2K |
| * #AFE_PORT_SAMPLE_RATE_96K |
| * #AFE_PORT_SAMPLE_RATE_176_4K |
| * #AFE_PORT_SAMPLE_RATE_192K |
| * #AFE_PORT_SAMPLE_RATE_352_8K |
| * #AFE_PORT_SAMPLE_RATE_384K |
| */ |
| uint32_t sample_rate; |
| |
| /* |
| * Bit width of the sample. |
| * @values 16, 24 |
| */ |
| uint16_t bit_width; |
| |
| /* |
| * Number of channels. |
| * @values 1 to #AFE_PORT_MAX_AUDIO_CHAN_CNT |
| */ |
| uint16_t num_channels; |
| |
| /* |
| * Data format supported by this port. |
| * If the port media type and device media type are different, |
| * it signifies a encoding/decoding use case |
| * @values |
| * #AFE_PORT_DATA_FORMAT_PCM |
| * #AFE_PORT_DATA_FORMAT_GENERIC_COMPRESSED |
| */ |
| uint16_t data_format; |
| |
| /*This field must be set to zero.*/ |
| uint16_t reserved; |
| } __packed; |
| |
| union afe_enc_config_data { |
| struct asm_sbc_enc_cfg_t sbc_config; |
| struct asm_aac_enc_cfg_v2_t aac_config; |
| struct asm_custom_enc_cfg_t custom_config; |
| struct asm_celt_enc_cfg_t celt_config; |
| struct asm_aptx_enc_cfg_t aptx_config; |
| struct asm_ldac_enc_cfg_t ldac_config; |
| }; |
| |
| struct afe_enc_config { |
| u32 format; |
| u32 scrambler_mode; |
| union afe_enc_config_data data; |
| }; |
| |
| struct afe_dec_config { |
| u32 format; |
| struct afe_abr_dec_cfg_t abr_dec_cfg; |
| }; |
| |
| struct afe_enc_cfg_blk_param_t { |
| uint32_t enc_cfg_blk_size; |
| /* |
| *Size of the encoder configuration block that follows this member |
| */ |
| union afe_enc_config_data enc_blk_config; |
| }; |
| |
| /* |
| * Payload of the AVS_ENCODER_PARAM_ID_PACKETIZER_ID parameter. |
| */ |
| struct avs_enc_packetizer_id_param_t { |
| /* |
| * Supported values: |
| * #AVS_MODULE_ID_PACKETIZER_COP |
| * Any OpenDSP supported values |
| */ |
| uint32_t enc_packetizer_id; |
| }; |
| |
| /* |
| * Payload of the AVS_ENCODER_PARAM_ID_ENABLE_SCRAMBLING parameter. |
| */ |
| struct avs_enc_set_scrambler_param_t { |
| /* |
| * Supported values: |
| * 1 : enable scrambler |
| * 0 : disable scrambler |
| */ |
| uint32_t enable_scrambler; |
| }; |
| |
| /* |
| * Payload of the AVS_ENCODER_PARAM_ID_BIT_RATE_LEVEL_MAP parameter. |
| */ |
| struct afe_enc_level_to_bitrate_map_param_t { |
| /* |
| * Parameter for mapping link quality level to bitrate. |
| */ |
| struct afe_quality_level_to_bitrate_info mapping_table; |
| }; |
| |
| /* |
| * Payload of the AVS_ENCDEC_PARAM_ID_DEC_TO_ENC_COMMUNICATION parameter. |
| */ |
| struct afe_enc_dec_imc_info_param_t { |
| /* |
| * Parameter to set up Inter Module Communication (IMC) between |
| * AFE Decoder and Encoder. |
| */ |
| struct afe_imc_dec_enc_info imc_info; |
| }; |
| |
| /* |
| * Payload of the AVS_DECODER_PARAM_ID_DEPACKETIZER_ID parameter. |
| */ |
| struct avs_dec_depacketizer_id_param_t { |
| /* |
| * Supported values: |
| * #AVS_MODULE_ID_DEPACKETIZER_COP |
| * Any OpenDSP supported values |
| */ |
| uint32_t dec_depacketizer_id; |
| }; |
| |
| union afe_port_config { |
| struct afe_param_id_pcm_cfg pcm; |
| struct afe_param_id_i2s_cfg i2s; |
| struct afe_param_id_hdmi_multi_chan_audio_cfg hdmi_multi_ch; |
| struct afe_param_id_slimbus_cfg slim_sch; |
| struct afe_param_id_rt_proxy_port_cfg rtproxy; |
| struct afe_param_id_internal_bt_fm_cfg int_bt_fm; |
| struct afe_param_id_pseudo_port_cfg pseudo_port; |
| struct afe_param_id_device_hw_delay_cfg hw_delay; |
| struct afe_param_id_spdif_cfg spdif; |
| struct afe_param_id_set_topology_cfg topology; |
| struct afe_param_id_tdm_cfg tdm; |
| struct afe_param_id_usb_audio_cfg usb_audio; |
| struct afe_param_id_aptx_sync_mode sync_mode_param; |
| struct afe_enc_fmt_id_param_t enc_fmt; |
| struct afe_port_media_type_t media_type; |
| struct afe_enc_cfg_blk_param_t enc_blk_param; |
| struct avs_enc_packetizer_id_param_t enc_pkt_id_param; |
| struct avs_enc_set_scrambler_param_t enc_set_scrambler_param; |
| struct avs_dec_depacketizer_id_param_t dec_depkt_id_param; |
| struct afe_enc_level_to_bitrate_map_param_t map_param; |
| struct afe_enc_dec_imc_info_param_t imc_info_param; |
| } __packed; |
| |
| struct afe_audioif_config_command_no_payload { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| } __packed; |
| |
| struct afe_audioif_config_command { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| union afe_port_config port; |
| } __packed; |
| |
| #define AFE_PORT_CMD_DEVICE_START 0x000100E5 |
| |
| /* Payload of the #AFE_PORT_CMD_DEVICE_START.*/ |
| struct afe_port_cmd_device_start { |
| struct apr_hdr hdr; |
| u16 port_id; |
| /* Port interface and direction (Rx or Tx) to start. An even |
| * number represents the Rx direction, and an odd number represents |
| * the Tx direction. |
| */ |
| |
| |
| u16 reserved; |
| /* Reserved for 32-bit alignment. This field must be set to 0.*/ |
| |
| } __packed; |
| |
| #define AFE_PORT_CMD_DEVICE_STOP 0x000100E6 |
| |
| /* Payload of the #AFE_PORT_CMD_DEVICE_STOP. */ |
| struct afe_port_cmd_device_stop { |
| struct apr_hdr hdr; |
| u16 port_id; |
| /* Port interface and direction (Rx or Tx) to start. An even |
| * number represents the Rx direction, and an odd number represents |
| * the Tx direction. |
| */ |
| |
| u16 reserved; |
| /* Reserved for 32-bit alignment. This field must be set to 0.*/ |
| } __packed; |
| |
| #define AFE_SERVICE_CMD_SHARED_MEM_MAP_REGIONS 0x000100EA |
| |
| /* Memory map regions command payload used by the |
| * #AFE_SERVICE_CMD_SHARED_MEM_MAP_REGIONS . |
| * This structure allows clients to map multiple shared memory |
| * regions in a single command. Following this structure are |
| * num_regions of afe_service_shared_map_region_payload. |
| */ |
| struct afe_service_cmd_shared_mem_map_regions { |
| struct apr_hdr hdr; |
| u16 mem_pool_id; |
| /* Type of memory on which this memory region is mapped. |
| * Supported values: |
| * - #ADSP_MEMORY_MAP_EBI_POOL |
| * - #ADSP_MEMORY_MAP_SMI_POOL |
| * - #ADSP_MEMORY_MAP_SHMEM8_4K_POOL |
| * - Other values are reserved |
| * |
| * The memory pool ID implicitly defines the characteristics of the |
| * memory. Characteristics may include alignment type, permissions, |
| * etc. |
| * |
| * ADSP_MEMORY_MAP_EBI_POOL is External Buffer Interface type memory |
| * ADSP_MEMORY_MAP_SMI_POOL is Shared Memory Interface type memory |
| * ADSP_MEMORY_MAP_SHMEM8_4K_POOL is shared memory, byte |
| * addressable, and 4 KB aligned. |
| */ |
| |
| |
| u16 num_regions; |
| /* Number of regions to map. |
| * Supported values: |
| * - Any value greater than zero |
| */ |
| |
| u32 property_flag; |
| /* Configures one common property for all the regions in the |
| * payload. |
| * |
| * Supported values: - 0x00000000 to 0x00000001 |
| * |
| * b0 - bit 0 indicates physical or virtual mapping 0 Shared memory |
| * address provided in afe_service_shared_map_region_payloadis a |
| * physical address. The shared memory needs to be mapped( hardware |
| * TLB entry) and a software entry needs to be added for internal |
| * book keeping. |
| * |
| * 1 Shared memory address provided in |
| * afe_service_shared_map_region_payloadis a virtual address. The |
| * shared memory must not be mapped (since hardware TLB entry is |
| * already available) but a software entry needs to be added for |
| * internal book keeping. This can be useful if two services with in |
| * ADSP is communicating via APR. They can now directly communicate |
| * via the Virtual address instead of Physical address. The virtual |
| * regions must be contiguous. num_regions must be 1 in this case. |
| * |
| * b31-b1 - reserved bits. must be set to zero |
| */ |
| |
| |
| } __packed; |
| /* Map region payload used by the |
| * afe_service_shared_map_region_payloadstructure. |
| */ |
| struct afe_service_shared_map_region_payload { |
| u32 shm_addr_lsw; |
| /* least significant word of starting address in the memory |
| * region to map. It must be contiguous memory, and it must be 4 KB |
| * aligned. |
| * Supported values: - Any 32 bit value |
| */ |
| |
| |
| u32 shm_addr_msw; |
| /* most significant word of startng address in the memory region |
| * to map. For 32 bit shared memory address, this field must be set |
| * to zero. For 36 bit shared memory address, bit31 to bit 4 must be |
| * set to zero |
| * |
| * Supported values: - For 32 bit shared memory address, this field |
| * must be set to zero. - For 36 bit shared memory address, bit31 to |
| * bit 4 must be set to zero - For 64 bit shared memory address, any |
| * 32 bit value |
| */ |
| |
| |
| u32 mem_size_bytes; |
| /* Number of bytes in the region. The aDSP will always map the |
| * regions as virtual contiguous memory, but the memory size must be |
| * in multiples of 4 KB to avoid gaps in the virtually contiguous |
| * mapped memory. |
| * |
| * Supported values: - multiples of 4KB |
| */ |
| |
| } __packed; |
| |
| #define AFE_SERVICE_CMDRSP_SHARED_MEM_MAP_REGIONS 0x000100EB |
| struct afe_service_cmdrsp_shared_mem_map_regions { |
| u32 mem_map_handle; |
| /* A memory map handle encapsulating shared memory attributes is |
| * returned iff AFE_SERVICE_CMD_SHARED_MEM_MAP_REGIONS command is |
| * successful. In the case of failure , a generic APR error response |
| * is returned to the client. |
| * |
| * Supported Values: - Any 32 bit value |
| */ |
| |
| } __packed; |
| #define AFE_SERVICE_CMD_SHARED_MEM_UNMAP_REGIONS 0x000100EC |
| /* Memory unmap regions command payload used by the |
| * #AFE_SERVICE_CMD_SHARED_MEM_UNMAP_REGIONS |
| * |
| * This structure allows clients to unmap multiple shared memory |
| * regions in a single command. |
| */ |
| |
| |
| struct afe_service_cmd_shared_mem_unmap_regions { |
| struct apr_hdr hdr; |
| u32 mem_map_handle; |
| /* memory map handle returned by |
| * AFE_SERVICE_CMD_SHARED_MEM_MAP_REGIONS commands |
| * |
| * Supported Values: |
| * - Any 32 bit value |
| */ |
| } __packed; |
| |
| #define AFE_PORT_CMD_GET_PARAM_V2 0x000100F0 |
| |
| /* Payload of the #AFE_PORT_CMD_GET_PARAM_V2 command, |
| * which queries for one post/preprocessing parameter of a |
| * stream. |
| */ |
| struct afe_port_cmd_get_param_v2 { |
| u16 port_id; |
| /* Port interface and direction (Rx or Tx) to start. */ |
| |
| u16 payload_size; |
| /* Maximum data size of the parameter ID/module ID combination. |
| * This is a multiple of four bytes |
| * Supported values: > 0 |
| */ |
| |
| u32 payload_address_lsw; |
| /* LSW of 64 bit Payload address. Address should be 32-byte, |
| * 4kbyte aligned and must be contig memory. |
| */ |
| |
| |
| u32 payload_address_msw; |
| /* MSW of 64 bit Payload address. In case of 32-bit shared |
| * memory address, this field must be set to zero. In case of 36-bit |
| * shared memory address, bit-4 to bit-31 must be set to zero. |
| * Address should be 32-byte, 4kbyte aligned and must be contiguous |
| * memory. |
| */ |
| |
| u32 mem_map_handle; |
| /* Memory map handle returned by |
| * AFE_SERVICE_CMD_SHARED_MEM_MAP_REGIONS commands. |
| * Supported Values: - NULL -- Message. The parameter data is |
| * in-band. - Non-NULL -- The parameter data is Out-band.Pointer to |
| * - the physical address in shared memory of the payload data. |
| * For detailed payload content, see the afe_port_param_data_v2 |
| * structure |
| */ |
| |
| |
| u32 module_id; |
| /* ID of the module to be queried. |
| * Supported values: Valid module ID |
| */ |
| |
| u32 param_id; |
| /* ID of the parameter to be queried. |
| * Supported values: Valid parameter ID |
| */ |
| } __packed; |
| |
| #define AFE_PORT_CMDRSP_GET_PARAM_V2 0x00010106 |
| |
| /* Payload of the #AFE_PORT_CMDRSP_GET_PARAM_V2 message, which |
| * responds to an #AFE_PORT_CMD_GET_PARAM_V2 command. |
| * |
| * Immediately following this structure is the parameters structure |
| * (afe_port_param_data) containing the response(acknowledgment) |
| * parameter payload. This payload is included for an in-band |
| * scenario. For an address/shared memory-based set parameter, this |
| * payload is not needed. |
| */ |
| |
| |
| struct afe_port_cmdrsp_get_param_v2 { |
| u32 status; |
| } __packed; |
| |
| #define AFE_PARAM_ID_LPASS_CORE_SHARED_CLOCK_CONFIG 0x0001028C |
| #define AFE_API_VERSION_LPASS_CORE_SHARED_CLK_CONFIG 0x1 |
| |
| /* Payload of the AFE_PARAM_ID_LPASS_CORE_SHARED_CLOCK_CONFIG parameter used by |
| * AFE_MODULE_AUDIO_DEV_INTERFACE. |
| */ |
| struct afe_param_id_lpass_core_shared_clk_cfg { |
| u32 lpass_core_shared_clk_cfg_minor_version; |
| /* |
| * Minor version used for lpass core shared clock configuration |
| * Supported value: AFE_API_VERSION_LPASS_CORE_SHARED_CLK_CONFIG |
| */ |
| u32 enable; |
| /* |
| * Specifies whether the lpass core shared clock is |
| * enabled (1) or disabled (0). |
| */ |
| } __packed; |
| |
| struct afe_lpass_core_shared_clk_config_command { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_param_id_lpass_core_shared_clk_cfg clk_cfg; |
| } __packed; |
| |
| /* adsp_afe_service_commands.h */ |
| |
| #define ADSP_MEMORY_MAP_EBI_POOL 0 |
| |
| #define ADSP_MEMORY_MAP_SMI_POOL 1 |
| #define ADSP_MEMORY_MAP_IMEM_POOL 2 |
| #define ADSP_MEMORY_MAP_SHMEM8_4K_POOL 3 |
| |
| /* Definition of virtual memory flag */ |
| #define ADSP_MEMORY_MAP_VIRTUAL_MEMORY 1 |
| |
| /* Definition of physical memory flag */ |
| #define ADSP_MEMORY_MAP_PHYSICAL_MEMORY 0 |
| |
| #define NULL_POPP_TOPOLOGY 0x00010C68 |
| #define NULL_COPP_TOPOLOGY 0x00010312 |
| #define DEFAULT_COPP_TOPOLOGY 0x00010314 |
| #define DEFAULT_POPP_TOPOLOGY 0x00010BE4 |
| #define COMPRESSED_PASSTHROUGH_DEFAULT_TOPOLOGY 0x0001076B |
| #define COMPRESSED_PASSTHROUGH_NONE_TOPOLOGY 0x00010774 |
| #define VPM_TX_SM_ECNS_COPP_TOPOLOGY 0x00010F71 |
| #define VPM_TX_SM_ECNS_V2_COPP_TOPOLOGY 0x00010F89 |
| #define VPM_TX_DM_FLUENCE_COPP_TOPOLOGY 0x00010F72 |
| #define VPM_TX_QMIC_FLUENCE_COPP_TOPOLOGY 0x00010F75 |
| #define VPM_TX_DM_RFECNS_COPP_TOPOLOGY 0x00010F86 |
| #define ADM_CMD_COPP_OPEN_TOPOLOGY_ID_DTS_HPX 0x10015002 |
| #define ADM_CMD_COPP_OPEN_TOPOLOGY_ID_AUDIOSPHERE 0x10028000 |
| |
| /* Memory map regions command payload used by the |
| * #ASM_CMD_SHARED_MEM_MAP_REGIONS ,#ADM_CMD_SHARED_MEM_MAP_REGIONS |
| * commands. |
| * |
| * This structure allows clients to map multiple shared memory |
| * regions in a single command. Following this structure are |
| * num_regions of avs_shared_map_region_payload. |
| */ |
| |
| |
| struct avs_cmd_shared_mem_map_regions { |
| struct apr_hdr hdr; |
| u16 mem_pool_id; |
| /* Type of memory on which this memory region is mapped. |
| * |
| * Supported values: - #ADSP_MEMORY_MAP_EBI_POOL - |
| * #ADSP_MEMORY_MAP_SMI_POOL - #ADSP_MEMORY_MAP_IMEM_POOL |
| * (unsupported) - #ADSP_MEMORY_MAP_SHMEM8_4K_POOL - Other values |
| * are reserved |
| * |
| * The memory ID implicitly defines the characteristics of the |
| * memory. Characteristics may include alignment type, permissions, |
| * etc. |
| * |
| * SHMEM8_4K is shared memory, byte addressable, and 4 KB aligned. |
| */ |
| |
| |
| u16 num_regions; |
| /* Number of regions to map.*/ |
| |
| u32 property_flag; |
| /* Configures one common property for all the regions in the |
| * payload. No two regions in the same memory map regions cmd can |
| * have differnt property. Supported values: - 0x00000000 to |
| * 0x00000001 |
| * |
| * b0 - bit 0 indicates physical or virtual mapping 0 shared memory |
| * address provided in avs_shared_map_regions_payload is physical |
| * address. The shared memory needs to be mapped( hardware TLB |
| * entry) |
| * |
| * and a software entry needs to be added for internal book keeping. |
| * |
| * 1 Shared memory address provided in MayPayload[usRegions] is |
| * virtual address. The shared memory must not be mapped (since |
| * hardware TLB entry is already available) but a software entry |
| * needs to be added for internal book keeping. This can be useful |
| * if two services with in ADSP is communicating via APR. They can |
| * now directly communicate via the Virtual address instead of |
| * Physical address. The virtual regions must be contiguous. |
| * |
| * b31-b1 - reserved bits. must be set to zero |
| */ |
| |
| } __packed; |
| |
| struct avs_shared_map_region_payload { |
| u32 shm_addr_lsw; |
| /* least significant word of shared memory address of the memory |
| * region to map. It must be contiguous memory, and it must be 4 KB |
| * aligned. |
| */ |
| |
| u32 shm_addr_msw; |
| /* most significant word of shared memory address of the memory |
| * region to map. For 32 bit shared memory address, this field must |
| * tbe set to zero. For 36 bit shared memory address, bit31 to bit 4 |
| * must be set to zero |
| */ |
| |
| u32 mem_size_bytes; |
| /* Number of bytes in the region. |
| * |
| * The aDSP will always map the regions as virtual contiguous |
| * memory, but the memory size must be in multiples of 4 KB to avoid |
| * gaps in the virtually contiguous mapped memory. |
| */ |
| |
| } __packed; |
| |
| struct avs_cmd_shared_mem_unmap_regions { |
| struct apr_hdr hdr; |
| u32 mem_map_handle; |
| /* memory map handle returned by ASM_CMD_SHARED_MEM_MAP_REGIONS |
| * , ADM_CMD_SHARED_MEM_MAP_REGIONS, commands |
| */ |
| |
| } __packed; |
| |
| /* Memory map command response payload used by the |
| * #ASM_CMDRSP_SHARED_MEM_MAP_REGIONS |
| * ,#ADM_CMDRSP_SHARED_MEM_MAP_REGIONS |
| */ |
| |
| |
| struct avs_cmdrsp_shared_mem_map_regions { |
| u32 mem_map_handle; |
| /* A memory map handle encapsulating shared memory attributes is |
| * returned |
| */ |
| |
| } __packed; |
| |
| /*adsp_audio_memmap_api.h*/ |
| |
| /* ASM related data structures */ |
| struct asm_wma_cfg { |
| u16 format_tag; |
| u16 ch_cfg; |
| u32 sample_rate; |
| u32 avg_bytes_per_sec; |
| u16 block_align; |
| u16 valid_bits_per_sample; |
| u32 ch_mask; |
| u16 encode_opt; |
| u16 adv_encode_opt; |
| u32 adv_encode_opt2; |
| u32 drc_peak_ref; |
| u32 drc_peak_target; |
| u32 drc_ave_ref; |
| u32 drc_ave_target; |
| } __packed; |
| |
| struct asm_wmapro_cfg { |
| u16 format_tag; |
| u16 ch_cfg; |
| u32 sample_rate; |
| u32 avg_bytes_per_sec; |
| u16 block_align; |
| u16 valid_bits_per_sample; |
| u32 ch_mask; |
| u16 encode_opt; |
| u16 adv_encode_opt; |
| u32 adv_encode_opt2; |
| u32 drc_peak_ref; |
| u32 drc_peak_target; |
| u32 drc_ave_ref; |
| u32 drc_ave_target; |
| } __packed; |
| |
| struct asm_aac_cfg { |
| u16 format; |
| u16 aot; |
| u16 ep_config; |
| u16 section_data_resilience; |
| u16 scalefactor_data_resilience; |
| u16 spectral_data_resilience; |
| u16 ch_cfg; |
| u16 reserved; |
| u32 sample_rate; |
| } __packed; |
| |
| struct asm_amrwbplus_cfg { |
| u32 size_bytes; |
| u32 version; |
| u32 num_channels; |
| u32 amr_band_mode; |
| u32 amr_dtx_mode; |
| u32 amr_frame_fmt; |
| u32 amr_lsf_idx; |
| } __packed; |
| |
| struct asm_flac_cfg { |
| u32 sample_rate; |
| u32 ext_sample_rate; |
| u32 min_frame_size; |
| u32 max_frame_size; |
| u16 stream_info_present; |
| u16 min_blk_size; |
| u16 max_blk_size; |
| u16 ch_cfg; |
| u16 sample_size; |
| u16 md5_sum; |
| }; |
| |
| struct asm_alac_cfg { |
| u32 frame_length; |
| u8 compatible_version; |
| u8 bit_depth; |
| u8 pb; |
| u8 mb; |
| u8 kb; |
| u8 num_channels; |
| u16 max_run; |
| u32 max_frame_bytes; |
| u32 avg_bit_rate; |
| u32 sample_rate; |
| u32 channel_layout_tag; |
| }; |
| |
| struct asm_g711_dec_cfg { |
| u32 sample_rate; |
| }; |
| |
| struct asm_vorbis_cfg { |
| u32 bit_stream_fmt; |
| }; |
| |
| struct asm_ape_cfg { |
| u16 compatible_version; |
| u16 compression_level; |
| u32 format_flags; |
| u32 blocks_per_frame; |
| u32 final_frame_blocks; |
| u32 total_frames; |
| u16 bits_per_sample; |
| u16 num_channels; |
| u32 sample_rate; |
| u32 seek_table_present; |
| }; |
| |
| struct asm_dsd_cfg { |
| u16 num_version; |
| u16 is_bitwise_big_endian; |
| u16 dsd_channel_block_size; |
| u16 num_channels; |
| u8 channel_mapping[8]; |
| u32 dsd_data_rate; |
| }; |
| |
| struct asm_softpause_params { |
| u32 enable; |
| u32 period; |
| u32 step; |
| u32 rampingcurve; |
| } __packed; |
| |
| struct asm_softvolume_params { |
| u32 period; |
| u32 step; |
| u32 rampingcurve; |
| } __packed; |
| |
| #define ASM_END_POINT_DEVICE_MATRIX 0 |
| |
| #define PCM_CHANNEL_NULL 0 |
| |
| /* Front left channel. */ |
| #define PCM_CHANNEL_FL 1 |
| |
| /* Front right channel. */ |
| #define PCM_CHANNEL_FR 2 |
| |
| /* Front center channel. */ |
| #define PCM_CHANNEL_FC 3 |
| |
| /* Left surround channel.*/ |
| #define PCM_CHANNEL_LS 4 |
| |
| /* Right surround channel.*/ |
| #define PCM_CHANNEL_RS 5 |
| |
| /* Low frequency effect channel. */ |
| #define PCM_CHANNEL_LFE 6 |
| |
| /* Center surround channel; Rear center channel. */ |
| #define PCM_CHANNEL_CS 7 |
| |
| /* Left back channel; Rear left channel. */ |
| #define PCM_CHANNEL_LB 8 |
| |
| /* Right back channel; Rear right channel. */ |
| #define PCM_CHANNEL_RB 9 |
| |
| /* Top surround channel. */ |
| #define PCM_CHANNELS 10 |
| |
| /* Center vertical height channel.*/ |
| #define PCM_CHANNEL_CVH 11 |
| |
| /* Mono surround channel.*/ |
| #define PCM_CHANNEL_MS 12 |
| |
| /* Front left of center. */ |
| #define PCM_CHANNEL_FLC 13 |
| |
| /* Front right of center. */ |
| #define PCM_CHANNEL_FRC 14 |
| |
| /* Rear left of center. */ |
| #define PCM_CHANNEL_RLC 15 |
| |
| /* Rear right of center. Update PCM_MAX_CHMAP_ID when |
| * this list is extended. |
| */ |
| #define PCM_CHANNEL_RRC 16 |
| |
| /* Max valid channel map index */ |
| #define PCM_MAX_CHMAP_ID PCM_CHANNEL_RRC |
| |
| #define PCM_FORMAT_MAX_NUM_CHANNEL 8 |
| |
| #define ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V2 0x00010DA5 |
| |
| #define ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V3 0x00010DDC |
| |
| #define ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V4 0x0001320C |
| |
| #define ASM_MEDIA_FMT_EVRCB_FS 0x00010BEF |
| |
| #define ASM_MEDIA_FMT_EVRCWB_FS 0x00010BF0 |
| |
| #define ASM_MEDIA_FMT_GENERIC_COMPRESSED 0x00013212 |
| |
| #define ASM_MAX_EQ_BANDS 12 |
| |
| #define ASM_DATA_CMD_MEDIA_FMT_UPDATE_V2 0x00010D98 |
| |
| struct asm_data_cmd_media_fmt_update_v2 { |
| u32 fmt_blk_size; |
| /* Media format block size in bytes.*/ |
| } __packed; |
| |
| struct asm_generic_compressed_fmt_blk_t { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmt_blk; |
| |
| /* |
| * Channel mapping array of bitstream output. |
| * Channel[i] mapping describes channel i inside the buffer, where |
| * i < num_channels. All valid used channels must be |
| * present at the beginning of the array. |
| */ |
| uint8_t channel_mapping[8]; |
| |
| /* |
| * Number of channels of the incoming bitstream. |
| * Supported values: 1,2,3,4,5,6,7,8 |
| */ |
| uint16_t num_channels; |
| |
| /* |
| * Nominal bits per sample value of the incoming bitstream. |
| * Supported values: 16, 32 |
| */ |
| uint16_t bits_per_sample; |
| |
| /* |
| * Nominal sampling rate of the incoming bitstream. |
| * Supported values: 8000, 11025, 16000, 22050, 24000, 32000, |
| * 44100, 48000, 88200, 96000, 176400, 192000, |
| * 352800, 384000 |
| */ |
| uint32_t sampling_rate; |
| |
| } __packed; |
| |
| |
| /* Command to send sample rate & channels for IEC61937 (compressed) or IEC60958 |
| * (pcm) streams. Both audio standards use the same format and are used for |
| * HDMI or SPDIF. |
| */ |
| #define ASM_DATA_CMD_IEC_60958_MEDIA_FMT 0x0001321E |
| |
| struct asm_iec_compressed_fmt_blk_t { |
| struct apr_hdr hdr; |
| |
| /* |
| * Nominal sampling rate of the incoming bitstream. |
| * Supported values: 8000, 11025, 16000, 22050, 24000, 32000, |
| * 44100, 48000, 88200, 96000, 176400, 192000, |
| * 352800, 384000 |
| */ |
| uint32_t sampling_rate; |
| |
| /* |
| * Number of channels of the incoming bitstream. |
| * Supported values: 1,2,3,4,5,6,7,8 |
| */ |
| uint32_t num_channels; |
| |
| } __packed; |
| |
| struct asm_multi_channel_pcm_fmt_blk_v2 { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmt_blk; |
| |
| u16 num_channels; |
| /* Number of channels. Supported values: 1 to 8 */ |
| u16 bits_per_sample; |
| /* Number of bits per sample per channel. * Supported values: |
| * 16, 24 * When used for playback, the client must send 24-bit |
| * samples packed in 32-bit words. The 24-bit samples must be placed |
| * in the most significant 24 bits of the 32-bit word. When used for |
| * recording, the aDSP sends 24-bit samples packed in 32-bit words. |
| * The 24-bit samples are placed in the most significant 24 bits of |
| * the 32-bit word. |
| */ |
| |
| |
| u32 sample_rate; |
| /* Number of samples per second (in Hertz). |
| * Supported values: 2000 to 48000 |
| */ |
| |
| u16 is_signed; |
| /* Flag that indicates the samples are signed (1). */ |
| |
| u16 reserved; |
| /* reserved field for 32 bit alignment. must be set to zero. */ |
| |
| u8 channel_mapping[8]; |
| /* Channel array of size 8. |
| * Supported values: |
| * - #PCM_CHANNEL_L |
| * - #PCM_CHANNEL_R |
| * - #PCM_CHANNEL_C |
| * - #PCM_CHANNEL_LS |
| * - #PCM_CHANNEL_RS |
| * - #PCM_CHANNEL_LFE |
| * - #PCM_CHANNEL_CS |
| * - #PCM_CHANNEL_LB |
| * - #PCM_CHANNEL_RB |
| * - #PCM_CHANNELS |
| * - #PCM_CHANNEL_CVH |
| * - #PCM_CHANNEL_MS |
| * - #PCM_CHANNEL_FLC |
| * - #PCM_CHANNEL_FRC |
| * - #PCM_CHANNEL_RLC |
| * - #PCM_CHANNEL_RRC |
| * |
| * Channel[i] mapping describes channel I. Each element i of the |
| * array describes channel I inside the buffer where 0 @le I < |
| * num_channels. An unused channel is set to zero. |
| */ |
| } __packed; |
| |
| struct asm_multi_channel_pcm_fmt_blk_v3 { |
| uint16_t num_channels; |
| /* |
| * Number of channels |
| * Supported values: 1 to 8 |
| */ |
| |
| uint16_t bits_per_sample; |
| /* |
| * Number of bits per sample per channel |
| * Supported values: 16, 24 |
| */ |
| |
| uint32_t sample_rate; |
| /* |
| * Number of samples per second |
| * Supported values: 2000 to 48000, 96000,192000 Hz |
| */ |
| |
| uint16_t is_signed; |
| /* Flag that indicates that PCM samples are signed (1) */ |
| |
| uint16_t sample_word_size; |
| /* |
| * Size in bits of the word that holds a sample of a channel. |
| * Supported values: 12,24,32 |
| */ |
| |
| uint8_t channel_mapping[8]; |
| /* |
| * Each element, i, in the array describes channel i inside the buffer where |
| * 0 <= i < num_channels. Unused channels are set to 0. |
| */ |
| } __packed; |
| |
| struct asm_multi_channel_pcm_fmt_blk_v4 { |
| uint16_t num_channels; |
| /* |
| * Number of channels |
| * Supported values: 1 to 8 |
| */ |
| |
| uint16_t bits_per_sample; |
| /* |
| * Number of bits per sample per channel |
| * Supported values: 16, 24, 32 |
| */ |
| |
| uint32_t sample_rate; |
| /* |
| * Number of samples per second |
| * Supported values: 2000 to 48000, 96000,192000 Hz |
| */ |
| |
| uint16_t is_signed; |
| /* Flag that indicates that PCM samples are signed (1) */ |
| |
| uint16_t sample_word_size; |
| /* |
| * Size in bits of the word that holds a sample of a channel. |
| * Supported values: 12,24,32 |
| */ |
| |
| uint8_t channel_mapping[8]; |
| /* |
| * Each element, i, in the array describes channel i inside the buffer where |
| * 0 <= i < num_channels. Unused channels are set to 0. |
| */ |
| uint16_t endianness; |
| /* |
| * Flag to indicate the endianness of the pcm sample |
| * Supported values: 0 - Little endian (all other formats) |
| * 1 - Big endian (AIFF) |
| */ |
| uint16_t mode; |
| /* |
| * Mode to provide additional info about the pcm input data. |
| * Supported values: 0 - Default QFs (Q15 for 16b, Q23 for packed 24b, |
| * Q31 for unpacked 24b or 32b) |
| * 15 - for 16 bit |
| * 23 - for 24b packed or 8.24 format |
| * 31 - for 24b unpacked or 32bit |
| */ |
| } __packed; |
| |
| /* |
| * Payload of the multichannel PCM configuration parameters in |
| * the ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V3 media format. |
| */ |
| struct asm_multi_channel_pcm_fmt_blk_param_v3 { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmt_blk; |
| struct asm_multi_channel_pcm_fmt_blk_v3 param; |
| } __packed; |
| |
| /* |
| * Payload of the multichannel PCM configuration parameters in |
| * the ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V4 media format. |
| */ |
| struct asm_multi_channel_pcm_fmt_blk_param_v4 { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmt_blk; |
| struct asm_multi_channel_pcm_fmt_blk_v4 param; |
| } __packed; |
| |
| struct asm_stream_cmd_set_encdec_param { |
| u32 param_id; |
| /* ID of the parameter. */ |
| |
| u32 param_size; |
| /* Data size of this parameter, in bytes. The size is a multiple |
| * of 4 bytes. |
| */ |
| |
| } __packed; |
| |
| struct asm_enc_cfg_blk_param_v2 { |
| u32 frames_per_buf; |
| /* Number of encoded frames to pack into each buffer. |
| * |
| * @note1hang This is only guidance information for the aDSP. The |
| * number of encoded frames put into each buffer (specified by the |
| * client) is less than or equal to this number. |
| */ |
| |
| u32 enc_cfg_blk_size; |
| /* Size in bytes of the encoder configuration block that follows |
| * this member. |
| */ |
| |
| } __packed; |
| |
| /* @brief Dolby Digital Plus end point configuration structure |
| */ |
| struct asm_dec_ddp_endp_param_v2 { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| int endp_param_value; |
| } __packed; |
| |
| /* |
| * Payload of the multichannel PCM encoder configuration parameters in |
| * the ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V4 media format. |
| */ |
| |
| struct asm_multi_channel_pcm_enc_cfg_v4 { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| struct asm_enc_cfg_blk_param_v2 encblk; |
| uint16_t num_channels; |
| /* |
| * Number of PCM channels. |
| * @values |
| * - 0 -- Native mode |
| * - 1 -- 8 channels |
| * Native mode indicates that encoding must be performed with the number |
| * of channels at the input. |
| */ |
| uint16_t bits_per_sample; |
| /* |
| * Number of bits per sample per channel. |
| * @values 16, 24 |
| */ |
| uint32_t sample_rate; |
| /* |
| * Number of samples per second. |
| * @values 0, 8000 to 48000 Hz |
| * A value of 0 indicates the native sampling rate. Encoding is |
| * performed at the input sampling rate. |
| */ |
| uint16_t is_signed; |
| /* |
| * Flag that indicates the PCM samples are signed (1). Currently, only |
| * signed PCM samples are supported. |
| */ |
| uint16_t sample_word_size; |
| /* |
| * The size in bits of the word that holds a sample of a channel. |
| * @values 16, 24, 32 |
| * 16-bit samples are always placed in 16-bit words: |
| * sample_word_size = 1. |
| * 24-bit samples can be placed in 32-bit words or in consecutive |
| * 24-bit words. |
| * - If sample_word_size = 32, 24-bit samples are placed in the |
| * most significant 24 bits of a 32-bit word. |
| * - If sample_word_size = 24, 24-bit samples are placed in |
| * 24-bit words. @tablebulletend |
| */ |
| uint8_t channel_mapping[8]; |
| /* |
| * Channel mapping array expected at the encoder output. |
| * Channel[i] mapping describes channel i inside the buffer, where |
| * 0 @le i < num_channels. All valid used channels must be present at |
| * the beginning of the array. |
| * If Native mode is set for the channels, this field is ignored. |
| * @values See Section @xref{dox:PcmChannelDefs} |
| */ |
| uint16_t endianness; |
| /* |
| * Flag to indicate the endianness of the pcm sample |
| * Supported values: 0 - Little endian (all other formats) |
| * 1 - Big endian (AIFF) |
| */ |
| uint16_t mode; |
| /* |
| * Mode to provide additional info about the pcm input data. |
| * Supported values: 0 - Default QFs (Q15 for 16b, Q23 for packed 24b, |
| * Q31 for unpacked 24b or 32b) |
| * 15 - for 16 bit |
| * 23 - for 24b packed or 8.24 format |
| * 31 - for 24b unpacked or 32bit |
| */ |
| } __packed; |
| |
| /* |
| * Payload of the multichannel PCM encoder configuration parameters in |
| * the ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V3 media format. |
| */ |
| |
| struct asm_multi_channel_pcm_enc_cfg_v3 { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| struct asm_enc_cfg_blk_param_v2 encblk; |
| uint16_t num_channels; |
| /* |
| * Number of PCM channels. |
| * @values |
| * - 0 -- Native mode |
| * - 1 -- 8 channels |
| * Native mode indicates that encoding must be performed with the number |
| * of channels at the input. |
| */ |
| uint16_t bits_per_sample; |
| /* |
| * Number of bits per sample per channel. |
| * @values 16, 24 |
| */ |
| uint32_t sample_rate; |
| /* |
| * Number of samples per second. |
| * @values 0, 8000 to 48000 Hz |
| * A value of 0 indicates the native sampling rate. Encoding is |
| * performed at the input sampling rate. |
| */ |
| uint16_t is_signed; |
| /* |
| * Flag that indicates the PCM samples are signed (1). Currently, only |
| * signed PCM samples are supported. |
| */ |
| uint16_t sample_word_size; |
| /* |
| * The size in bits of the word that holds a sample of a channel. |
| * @values 16, 24, 32 |
| * 16-bit samples are always placed in 16-bit words: |
| * sample_word_size = 1. |
| * 24-bit samples can be placed in 32-bit words or in consecutive |
| * 24-bit words. |
| * - If sample_word_size = 32, 24-bit samples are placed in the |
| * most significant 24 bits of a 32-bit word. |
| * - If sample_word_size = 24, 24-bit samples are placed in |
| * 24-bit words. @tablebulletend |
| */ |
| uint8_t channel_mapping[8]; |
| /* |
| * Channel mapping array expected at the encoder output. |
| * Channel[i] mapping describes channel i inside the buffer, where |
| * 0 @le i < num_channels. All valid used channels must be present at |
| * the beginning of the array. |
| * If Native mode is set for the channels, this field is ignored. |
| * @values See Section @xref{dox:PcmChannelDefs} |
| */ |
| }; |
| |
| /* @brief Multichannel PCM encoder configuration structure used |
| * in the #ASM_PARAM_ID_ENCDEC_ENC_CFG_BLK_V2 command. |
| */ |
| |
| struct asm_multi_channel_pcm_enc_cfg_v2 { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| struct asm_enc_cfg_blk_param_v2 encblk; |
| uint16_t num_channels; |
| /*< Number of PCM channels. |
| * |
| * Supported values: - 0 -- Native mode - 1 -- 8 Native mode |
| * indicates that encoding must be performed with the number of |
| * channels at the input. |
| */ |
| |
| uint16_t bits_per_sample; |
| /*< Number of bits per sample per channel. |
| * Supported values: 16, 24 |
| */ |
| |
| uint32_t sample_rate; |
| /*< Number of samples per second (in Hertz). |
| * |
| * Supported values: 0, 8000 to 48000 A value of 0 indicates the |
| * native sampling rate. Encoding is performed at the input sampling |
| * rate. |
| */ |
| |
| uint16_t is_signed; |
| /*< Specifies whether the samples are signed (1). Currently, |
| * only signed samples are supported. |
| */ |
| |
| uint16_t reserved; |
| /*< reserved field for 32 bit alignment. must be set to zero.*/ |
| |
| |
| uint8_t channel_mapping[8]; |
| } __packed; |
| |
| #define ASM_MEDIA_FMT_MP3 0x00010BE9 |
| #define ASM_MEDIA_FMT_AAC_V2 0x00010DA6 |
| |
| /* @xreflabel |
| * {hdr:AsmMediaFmtDolbyAac} Media format ID for the |
| * Dolby AAC decoder. This format ID is be used if the client wants |
| * to use the Dolby AAC decoder to decode MPEG2 and MPEG4 AAC |
| * contents. |
| */ |
| |
| #define ASM_MEDIA_FMT_DOLBY_AAC 0x00010D86 |
| |
| /* Enumeration for the audio data transport stream AAC format. */ |
| #define ASM_MEDIA_FMT_AAC_FORMAT_FLAG_ADTS 0 |
| |
| /* Enumeration for low overhead audio stream AAC format. */ |
| #define ASM_MEDIA_FMT_AAC_FORMAT_FLAG_LOAS 1 |
| |
| /* Enumeration for the audio data interchange format |
| * AAC format. |
| */ |
| #define ASM_MEDIA_FMT_AAC_FORMAT_FLAG_ADIF 2 |
| |
| /* Enumeration for the raw AAC format. */ |
| #define ASM_MEDIA_FMT_AAC_FORMAT_FLAG_RAW 3 |
| |
| /* Enumeration for the AAC LATM format. */ |
| #define ASM_MEDIA_FMT_AAC_FORMAT_FLAG_LATM 4 |
| |
| #define ASM_MEDIA_FMT_AAC_AOT_LC 2 |
| #define ASM_MEDIA_FMT_AAC_AOT_SBR 5 |
| #define ASM_MEDIA_FMT_AAC_AOT_PS 29 |
| #define ASM_MEDIA_FMT_AAC_AOT_BSAC 22 |
| |
| struct asm_aac_fmt_blk_v2 { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmt_blk; |
| |
| u16 aac_fmt_flag; |
| /* Bitstream format option. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_AAC_FORMAT_FLAG_ADTS |
| * - #ASM_MEDIA_FMT_AAC_FORMAT_FLAG_LOAS |
| * - #ASM_MEDIA_FMT_AAC_FORMAT_FLAG_ADIF |
| * - #ASM_MEDIA_FMT_AAC_FORMAT_FLAG_RAW |
| */ |
| |
| u16 audio_objype; |
| /* Audio Object Type (AOT) present in the AAC stream. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_AAC_AOT_LC |
| * - #ASM_MEDIA_FMT_AAC_AOT_SBR |
| * - #ASM_MEDIA_FMT_AAC_AOT_BSAC |
| * - #ASM_MEDIA_FMT_AAC_AOT_PS |
| * - Otherwise -- Not supported |
| */ |
| |
| u16 channel_config; |
| /* Number of channels present in the AAC stream. |
| * Supported values: |
| * - 1 -- Mono |
| * - 2 -- Stereo |
| * - 6 -- 5.1 content |
| */ |
| |
| u16 total_size_of_PCE_bits; |
| /* greater or equal to zero. * -In case of RAW formats and |
| * channel config = 0 (PCE), client can send * the bit stream |
| * containing PCE immediately following this structure * (in-band). |
| * -This number does not include bits included for 32 bit alignment. |
| * -If zero, then the PCE info is assumed to be available in the |
| * audio -bit stream & not in-band. |
| */ |
| |
| u32 sample_rate; |
| /* Number of samples per second (in Hertz). |
| * |
| * Supported values: 8000, 11025, 12000, 16000, 22050, 24000, 32000, |
| * 44100, 48000 |
| * |
| * This field must be equal to the sample rate of the AAC-LC |
| * decoder's output. - For MP4 or 3GP containers, this is indicated |
| * by the samplingFrequencyIndex field in the AudioSpecificConfig |
| * element. - For ADTS format, this is indicated by the |
| * samplingFrequencyIndex in the ADTS fixed header. - For ADIF |
| * format, this is indicated by the samplingFrequencyIndex in the |
| * program_config_element present in the ADIF header. |
| */ |
| |
| } __packed; |
| |
| struct asm_aac_enc_cfg_v2 { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| struct asm_enc_cfg_blk_param_v2 encblk; |
| |
| u32 bit_rate; |
| /* Encoding rate in bits per second. */ |
| u32 enc_mode; |
| /* Encoding mode. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_AAC_AOT_LC |
| * - #ASM_MEDIA_FMT_AAC_AOT_SBR |
| * - #ASM_MEDIA_FMT_AAC_AOT_PS |
| */ |
| u16 aac_fmt_flag; |
| /* AAC format flag. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_AAC_FORMAT_FLAG_ADTS |
| * - #ASM_MEDIA_FMT_AAC_FORMAT_FLAG_RAW |
| */ |
| u16 channel_cfg; |
| /* Number of channels to encode. |
| * Supported values: |
| * - 0 -- Native mode |
| * - 1 -- Mono |
| * - 2 -- Stereo |
| * - Other values are not supported. |
| * @note1hang The eAAC+ encoder mode supports only stereo. |
| * Native mode indicates that encoding must be performed with the |
| * number of channels at the input. |
| * The number of channels must not change during encoding. |
| */ |
| |
| u32 sample_rate; |
| /* Number of samples per second. |
| * Supported values: - 0 -- Native mode - For other values, |
| * Native mode indicates that encoding must be performed with the |
| * sampling rate at the input. |
| * The sampling rate must not change during encoding. |
| */ |
| |
| } __packed; |
| |
| #define ASM_MEDIA_FMT_G711_ALAW_FS 0x00010BF7 |
| #define ASM_MEDIA_FMT_G711_MLAW_FS 0x00010C2E |
| |
| struct asm_g711_enc_cfg_v2 { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| struct asm_enc_cfg_blk_param_v2 encblk; |
| |
| u32 sample_rate; |
| /* |
| * Number of samples per second. |
| * Supported values: 8000, 16000 Hz |
| */ |
| |
| } __packed; |
| |
| struct asm_vorbis_fmt_blk_v2 { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmtblk; |
| u32 bit_stream_fmt; |
| /* Bit stream format. |
| * Supported values: |
| * - 0 -- Raw bitstream |
| * - 1 -- Transcoded bitstream |
| * |
| * Transcoded bitstream containing the size of the frame as the first |
| * word in each frame. |
| */ |
| |
| } __packed; |
| |
| struct asm_flac_fmt_blk_v2 { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmtblk; |
| |
| u16 is_stream_info_present; |
| /* Specifies whether stream information is present in the FLAC format |
| * block. |
| * |
| * Supported values: |
| * - 0 -- Stream information is not present in this message |
| * - 1 -- Stream information is present in this message |
| * |
| * When set to 1, the FLAC bitstream was successfully parsed by the |
| * client, and other fields in the FLAC format block can be read by the |
| * decoder to get metadata stream information. |
| */ |
| |
| u16 num_channels; |
| /* Number of channels for decoding. |
| * Supported values: 1 to 2 |
| */ |
| |
| u16 min_blk_size; |
| /* Minimum block size (in samples) used in the stream. It must be less |
| * than or equal to max_blk_size. |
| */ |
| |
| u16 max_blk_size; |
| /* Maximum block size (in samples) used in the stream. If the |
| * minimum block size equals the maximum block size, a fixed block |
| * size stream is implied. |
| */ |
| |
| u16 md5_sum[8]; |
| /* MD5 signature array of the unencoded audio data. This allows the |
| * decoder to determine if an error exists in the audio data, even when |
| * the error does not result in an invalid bitstream. |
| */ |
| |
| u32 sample_rate; |
| /* Number of samples per second. |
| * Supported values: 8000 to 48000 Hz |
| */ |
| |
| u32 min_frame_size; |
| /* Minimum frame size used in the stream. |
| * Supported values: |
| * - > 0 bytes |
| * - 0 -- The value is unknown |
| */ |
| |
| u32 max_frame_size; |
| /* Maximum frame size used in the stream. |
| * Supported values: |
| * -- > 0 bytes |
| * -- 0 . The value is unknown |
| */ |
| |
| u16 sample_size; |
| /* Bits per sample.Supported values: 8, 16 */ |
| |
| u16 reserved; |
| /* Clients must set this field to zero |
| */ |
| |
| } __packed; |
| |
| struct asm_alac_fmt_blk_v2 { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmtblk; |
| |
| u32 frame_length; |
| u8 compatible_version; |
| u8 bit_depth; |
| u8 pb; |
| u8 mb; |
| u8 kb; |
| u8 num_channels; |
| u16 max_run; |
| u32 max_frame_bytes; |
| u32 avg_bit_rate; |
| u32 sample_rate; |
| u32 channel_layout_tag; |
| |
| } __packed; |
| |
| struct asm_g711_dec_fmt_blk_v2 { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmtblk; |
| u32 sample_rate; |
| } __packed; |
| |
| struct asm_ape_fmt_blk_v2 { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmtblk; |
| |
| u16 compatible_version; |
| u16 compression_level; |
| u32 format_flags; |
| u32 blocks_per_frame; |
| u32 final_frame_blocks; |
| u32 total_frames; |
| u16 bits_per_sample; |
| u16 num_channels; |
| u32 sample_rate; |
| u32 seek_table_present; |
| |
| } __packed; |
| |
| struct asm_dsd_fmt_blk_v2 { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmtblk; |
| |
| u16 num_version; |
| u16 is_bitwise_big_endian; |
| u16 dsd_channel_block_size; |
| u16 num_channels; |
| u8 channel_mapping[8]; |
| u32 dsd_data_rate; |
| |
| } __packed; |
| |
| #define ASM_MEDIA_FMT_AMRNB_FS 0x00010BEB |
| |
| /* Enumeration for 4.75 kbps AMR-NB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRNB_FS_ENCODE_MODE_MR475 0 |
| |
| /* Enumeration for 5.15 kbps AMR-NB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRNB_FS_ENCODE_MODE_MR515 1 |
| |
| /* Enumeration for 5.90 kbps AMR-NB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRNB_FS_ENCODE_MODE_MMR59 2 |
| |
| /* Enumeration for 6.70 kbps AMR-NB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRNB_FS_ENCODE_MODE_MMR67 3 |
| |
| /* Enumeration for 7.40 kbps AMR-NB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRNB_FS_ENCODE_MODE_MMR74 4 |
| |
| /* Enumeration for 7.95 kbps AMR-NB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRNB_FS_ENCODE_MODE_MMR795 5 |
| |
| /* Enumeration for 10.20 kbps AMR-NB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRNB_FS_ENCODE_MODE_MMR102 6 |
| |
| /* Enumeration for 12.20 kbps AMR-NB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRNB_FS_ENCODE_MODE_MMR122 7 |
| |
| /* Enumeration for AMR-NB Discontinuous Transmission mode off. */ |
| #define ASM_MEDIA_FMT_AMRNB_FS_DTX_MODE_OFF 0 |
| |
| /* Enumeration for AMR-NB DTX mode VAD1. */ |
| #define ASM_MEDIA_FMT_AMRNB_FS_DTX_MODE_VAD1 1 |
| |
| /* Enumeration for AMR-NB DTX mode VAD2. */ |
| #define ASM_MEDIA_FMT_AMRNB_FS_DTX_MODE_VAD2 2 |
| |
| /* Enumeration for AMR-NB DTX mode auto. */ |
| #define ASM_MEDIA_FMT_AMRNB_FS_DTX_MODE_AUTO 3 |
| |
| struct asm_amrnb_enc_cfg { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| struct asm_enc_cfg_blk_param_v2 encblk; |
| |
| u16 enc_mode; |
| /* AMR-NB encoding rate. |
| * Supported values: |
| * Use the ASM_MEDIA_FMT_AMRNB_FS_ENCODE_MODE_* |
| * macros |
| */ |
| |
| u16 dtx_mode; |
| /* Specifies whether DTX mode is disabled or enabled. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_AMRNB_FS_DTX_MODE_OFF |
| * - #ASM_MEDIA_FMT_AMRNB_FS_DTX_MODE_VAD1 |
| */ |
| } __packed; |
| |
| #define ASM_MEDIA_FMT_AMRWB_FS 0x00010BEC |
| |
| /* Enumeration for 6.6 kbps AMR-WB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRWB_FS_ENCODE_MODE_MR66 0 |
| |
| /* Enumeration for 8.85 kbps AMR-WB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRWB_FS_ENCODE_MODE_MR885 1 |
| |
| /* Enumeration for 12.65 kbps AMR-WB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRWB_FS_ENCODE_MODE_MR1265 2 |
| |
| /* Enumeration for 14.25 kbps AMR-WB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRWB_FS_ENCODE_MODE_MR1425 3 |
| |
| /* Enumeration for 15.85 kbps AMR-WB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRWB_FS_ENCODE_MODE_MR1585 4 |
| |
| /* Enumeration for 18.25 kbps AMR-WB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRWB_FS_ENCODE_MODE_MR1825 5 |
| |
| /* Enumeration for 19.85 kbps AMR-WB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRWB_FS_ENCODE_MODE_MR1985 6 |
| |
| /* Enumeration for 23.05 kbps AMR-WB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRWB_FS_ENCODE_MODE_MR2305 7 |
| |
| /* Enumeration for 23.85 kbps AMR-WB Encoding mode. */ |
| #define ASM_MEDIA_FMT_AMRWB_FS_ENCODE_MODE_MR2385 8 |
| |
| struct asm_amrwb_enc_cfg { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| struct asm_enc_cfg_blk_param_v2 encblk; |
| |
| u16 enc_mode; |
| /* AMR-WB encoding rate. |
| * Suupported values: |
| * Use the ASM_MEDIA_FMT_AMRWB_FS_ENCODE_MODE_* |
| * macros |
| */ |
| |
| u16 dtx_mode; |
| /* Specifies whether DTX mode is disabled or enabled. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_AMRNB_FS_DTX_MODE_OFF |
| * - #ASM_MEDIA_FMT_AMRNB_FS_DTX_MODE_VAD1 |
| */ |
| } __packed; |
| |
| #define ASM_MEDIA_FMT_V13K_FS 0x00010BED |
| |
| /* Enumeration for 14.4 kbps V13K Encoding mode. */ |
| #define ASM_MEDIA_FMT_V13K_FS_ENCODE_MODE_MR1440 0 |
| |
| /* Enumeration for 12.2 kbps V13K Encoding mode. */ |
| #define ASM_MEDIA_FMT_V13K_FS_ENCODE_MODE_MR1220 1 |
| |
| /* Enumeration for 11.2 kbps V13K Encoding mode. */ |
| #define ASM_MEDIA_FMT_V13K_FS_ENCODE_MODE_MR1120 2 |
| |
| /* Enumeration for 9.0 kbps V13K Encoding mode. */ |
| #define ASM_MEDIA_FMT_V13K_FS_ENCODE_MODE_MR90 3 |
| |
| /* Enumeration for 7.2 kbps V13K eEncoding mode. */ |
| #define ASM_MEDIA_FMT_V13K_FS_ENCODE_MODE_MR720 4 |
| |
| /* Enumeration for 1/8 vocoder rate.*/ |
| #define ASM_MEDIA_FMT_VOC_ONE_EIGHTH_RATE 1 |
| |
| /* Enumeration for 1/4 vocoder rate. */ |
| #define ASM_MEDIA_FMT_VOC_ONE_FOURTH_RATE 2 |
| |
| /* Enumeration for 1/2 vocoder rate. */ |
| #define ASM_MEDIA_FMT_VOC_HALF_RATE 3 |
| |
| /* Enumeration for full vocoder rate. */ |
| #define ASM_MEDIA_FMT_VOC_FULL_RATE 4 |
| |
| struct asm_v13k_enc_cfg { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| struct asm_enc_cfg_blk_param_v2 encblk; |
| u16 max_rate; |
| /* Maximum allowed encoder frame rate. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_VOC_ONE_EIGHTH_RATE |
| * - #ASM_MEDIA_FMT_VOC_ONE_FOURTH_RATE |
| * - #ASM_MEDIA_FMT_VOC_HALF_RATE |
| * - #ASM_MEDIA_FMT_VOC_FULL_RATE |
| */ |
| |
| u16 min_rate; |
| /* Minimum allowed encoder frame rate. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_VOC_ONE_EIGHTH_RATE |
| * - #ASM_MEDIA_FMT_VOC_ONE_FOURTH_RATE |
| * - #ASM_MEDIA_FMT_VOC_HALF_RATE |
| * - #ASM_MEDIA_FMT_VOC_FULL_RATE |
| */ |
| |
| u16 reduced_rate_cmd; |
| /* Reduced rate command, used to change |
| * the average bitrate of the V13K |
| * vocoder. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_V13K_FS_ENCODE_MODE_MR1440 (Default) |
| * - #ASM_MEDIA_FMT_V13K_FS_ENCODE_MODE_MR1220 |
| * - #ASM_MEDIA_FMT_V13K_FS_ENCODE_MODE_MR1120 |
| * - #ASM_MEDIA_FMT_V13K_FS_ENCODE_MODE_MR90 |
| * - #ASM_MEDIA_FMT_V13K_FS_ENCODE_MODE_MR720 |
| */ |
| |
| u16 rate_mod_cmd; |
| /* Rate modulation command. Default = 0. |
| *- If bit 0=1, rate control is enabled. |
| *- If bit 1=1, the maximum number of consecutive full rate |
| * frames is limited with numbers supplied in |
| * bits 2 to 10. |
| *- If bit 1=0, the minimum number of non-full rate frames |
| * in between two full rate frames is forced to |
| * the number supplied in bits 2 to 10. In both cases, if necessary, |
| * half rate is used to substitute full rate. - Bits 15 to 10 are |
| * reserved and must all be set to zero. |
| */ |
| |
| } __packed; |
| |
| #define ASM_MEDIA_FMT_EVRC_FS 0x00010BEE |
| |
| /* EVRC encoder configuration structure used in the |
| * #ASM_PARAM_ID_ENCDEC_ENC_CFG_BLK_V2 command. |
| */ |
| struct asm_evrc_enc_cfg { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| struct asm_enc_cfg_blk_param_v2 encblk; |
| u16 max_rate; |
| /* Maximum allowed encoder frame rate. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_VOC_ONE_EIGHTH_RATE |
| * - #ASM_MEDIA_FMT_VOC_ONE_FOURTH_RATE |
| * - #ASM_MEDIA_FMT_VOC_HALF_RATE |
| * - #ASM_MEDIA_FMT_VOC_FULL_RATE |
| */ |
| |
| u16 min_rate; |
| /* Minimum allowed encoder frame rate. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_VOC_ONE_EIGHTH_RATE |
| * - #ASM_MEDIA_FMT_VOC_ONE_FOURTH_RATE |
| * - #ASM_MEDIA_FMT_VOC_HALF_RATE |
| * - #ASM_MEDIA_FMT_VOC_FULL_RATE |
| */ |
| |
| u16 rate_mod_cmd; |
| /* Rate modulation command. Default: 0. |
| * - If bit 0=1, rate control is enabled. |
| * - If bit 1=1, the maximum number of consecutive full rate frames |
| * is limited with numbers supplied in bits 2 to 10. |
| * |
| * - If bit 1=0, the minimum number of non-full rate frames in |
| * between two full rate frames is forced to the number supplied in |
| * bits 2 to 10. In both cases, if necessary, half rate is used to |
| * substitute full rate. |
| * |
| * - Bits 15 to 10 are reserved and must all be set to zero. |
| */ |
| |
| u16 reserved; |
| /* Reserved. Clients must set this field to zero. */ |
| } __packed; |
| |
| #define ASM_MEDIA_FMT_WMA_V10PRO_V2 0x00010DA7 |
| |
| struct asm_wmaprov10_fmt_blk_v2 { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmtblk; |
| |
| u16 fmtag; |
| /* WMA format type. |
| * Supported values: |
| * - 0x162 -- WMA 9 Pro |
| * - 0x163 -- WMA 9 Pro Lossless |
| * - 0x166 -- WMA 10 Pro |
| * - 0x167 -- WMA 10 Pro Lossless |
| */ |
| |
| u16 num_channels; |
| /* Number of channels encoded in the input stream. |
| * Supported values: 1 to 8 |
| */ |
| |
| u32 sample_rate; |
| /* Number of samples per second (in Hertz). |
| * Supported values: 11025, 16000, 22050, 32000, 44100, 48000, |
| * 88200, 96000 |
| */ |
| |
| u32 avg_bytes_per_sec; |
| /* Bitrate expressed as the average bytes per second. |
| * Supported values: 2000 to 96000 |
| */ |
| |
| u16 blk_align; |
| /* Size of the bitstream packet size in bytes. WMA Pro files |
| * have a payload of one block per bitstream packet. |
| * Supported values: @le 13376 |
| */ |
| |
| u16 bits_per_sample; |
| /* Number of bits per sample in the encoded WMA stream. |
| * Supported values: 16, 24 |
| */ |
| |
| u32 channel_mask; |
| /* Bit-packed double word (32-bits) that indicates the |
| * recommended speaker positions for each source channel. |
| */ |
| |
| u16 enc_options; |
| /* Bit-packed word with values that indicate whether certain |
| * features of the bitstream are used. |
| * Supported values: - 0x0001 -- ENCOPT3_PURE_LOSSLESS - 0x0006 -- |
| * ENCOPT3_FRM_SIZE_MOD - 0x0038 -- ENCOPT3_SUBFRM_DIV - 0x0040 -- |
| * ENCOPT3_WRITE_FRAMESIZE_IN_HDR - 0x0080 -- |
| * ENCOPT3_GENERATE_DRC_PARAMS - 0x0100 -- ENCOPT3_RTMBITS |
| */ |
| |
| |
| u16 usAdvancedEncodeOpt; |
| /* Advanced encoding option. */ |
| |
| u32 advanced_enc_options2; |
| /* Advanced encoding option 2. */ |
| |
| } __packed; |
| |
| #define ASM_MEDIA_FMT_WMA_V9_V2 0x00010DA8 |
| struct asm_wmastdv9_fmt_blk_v2 { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmtblk; |
| u16 fmtag; |
| /* WMA format tag. |
| * Supported values: 0x161 (WMA 9 standard) |
| */ |
| |
| u16 num_channels; |
| /* Number of channels in the stream. |
| * Supported values: 1, 2 |
| */ |
| |
| u32 sample_rate; |
| /* Number of samples per second (in Hertz). |
| * Supported values: 48000 |
| */ |
| |
| u32 avg_bytes_per_sec; |
| /* Bitrate expressed as the average bytes per second. */ |
| |
| u16 blk_align; |
| /* Block align. All WMA files with a maximum packet size of |
| * 13376 are supported. |
| */ |
| |
| |
| u16 bits_per_sample; |
| /* Number of bits per sample in the output. |
| * Supported values: 16 |
| */ |
| |
| u32 channel_mask; |
| /* Channel mask. |
| * Supported values: |
| * - 3 -- Stereo (front left/front right) |
| * - 4 -- Mono (center) |
| */ |
| |
| u16 enc_options; |
| /* Options used during encoding. */ |
| |
| u16 reserved; |
| |
| } __packed; |
| |
| #define ASM_MEDIA_FMT_WMA_V8 0x00010D91 |
| |
| struct asm_wmastdv8_enc_cfg { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| struct asm_enc_cfg_blk_param_v2 encblk; |
| u32 bit_rate; |
| /* Encoding rate in bits per second. */ |
| |
| u32 sample_rate; |
| /* Number of samples per second. |
| * |
| * Supported values: |
| * - 0 -- Native mode |
| * - Other Supported values are 22050, 32000, 44100, and 48000. |
| * |
| * Native mode indicates that encoding must be performed with the |
| * sampling rate at the input. |
| * The sampling rate must not change during encoding. |
| */ |
| |
| u16 channel_cfg; |
| /* Number of channels to encode. |
| * Supported values: |
| * - 0 -- Native mode |
| * - 1 -- Mono |
| * - 2 -- Stereo |
| * - Other values are not supported. |
| * |
| * Native mode indicates that encoding must be performed with the |
| * number of channels at the input. |
| * The number of channels must not change during encoding. |
| */ |
| |
| u16 reserved; |
| /* Reserved. Clients must set this field to zero.*/ |
| } __packed; |
| |
| #define ASM_MEDIA_FMT_AMR_WB_PLUS_V2 0x00010DA9 |
| |
| struct asm_amrwbplus_fmt_blk_v2 { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmtblk; |
| u32 amr_frame_fmt; |
| /* AMR frame format. |
| * Supported values: |
| * - 6 -- Transport Interface Format (TIF) |
| * - Any other value -- File storage format (FSF) |
| * |
| * TIF stream contains 2-byte header for each frame within the |
| * superframe. FSF stream contains one 2-byte header per superframe. |
| */ |
| |
| } __packed; |
| |
| #define ASM_MEDIA_FMT_AC3 0x00010DEE |
| #define ASM_MEDIA_FMT_EAC3 0x00010DEF |
| #define ASM_MEDIA_FMT_DTS 0x00010D88 |
| #define ASM_MEDIA_FMT_MP2 0x00010DE9 |
| #define ASM_MEDIA_FMT_FLAC 0x00010C16 |
| #define ASM_MEDIA_FMT_ALAC 0x00012F31 |
| #define ASM_MEDIA_FMT_VORBIS 0x00010C15 |
| #define ASM_MEDIA_FMT_APE 0x00012F32 |
| #define ASM_MEDIA_FMT_DSD 0x00012F3E |
| #define ASM_MEDIA_FMT_TRUEHD 0x00013215 |
| /* 0x0 is used for fomat ID since ADSP dynamically determines the |
| * format encapsulated in the IEC61937 (compressed) or IEC60958 |
| * (pcm) packets. |
| */ |
| #define ASM_MEDIA_FMT_IEC 0x00000000 |
| |
| /* Media format ID for adaptive transform acoustic coding. This |
| * ID is used by the #ASM_STREAM_CMD_OPEN_WRITE_COMPRESSED command |
| * only. |
| */ |
| |
| #define ASM_MEDIA_FMT_ATRAC 0x00010D89 |
| |
| /* Media format ID for metadata-enhanced audio transmission. |
| * This ID is used by the #ASM_STREAM_CMD_OPEN_WRITE_COMPRESSED |
| * command only. |
| */ |
| |
| #define ASM_MEDIA_FMT_MAT 0x00010D8A |
| |
| /* adsp_media_fmt.h */ |
| |
| #define ASM_DATA_CMD_WRITE_V2 0x00010DAB |
| |
| struct asm_data_cmd_write_v2 { |
| struct apr_hdr hdr; |
| u32 buf_addr_lsw; |
| /* The 64 bit address msw-lsw should be a valid, mapped address. |
| * 64 bit address should be a multiple of 32 bytes |
| */ |
| |
| u32 buf_addr_msw; |
| /* The 64 bit address msw-lsw should be a valid, mapped address. |
| * 64 bit address should be a multiple of 32 bytes. |
| * -Address of the buffer containing the data to be decoded. |
| * The buffer should be aligned to a 32 byte boundary. |
| * -In the case of 32 bit Shared memory address, msw field must |
| * -be set to zero. |
| * -In the case of 36 bit shared memory address, bit 31 to bit 4 |
| * -of msw must be set to zero. |
| */ |
| u32 mem_map_handle; |
| /* memory map handle returned by DSP through |
| * ASM_CMD_SHARED_MEM_MAP_REGIONS command |
| */ |
| u32 buf_size; |
| /* Number of valid bytes available in the buffer for decoding. The |
| * first byte starts at buf_addr. |
| */ |
| |
| u32 seq_id; |
| /* Optional buffer sequence ID. */ |
| |
| u32 timestamp_lsw; |
| /* Lower 32 bits of the 64-bit session time in microseconds of the |
| * first buffer sample. |
| */ |
| |
| u32 timestamp_msw; |
| /* Upper 32 bits of the 64-bit session time in microseconds of the |
| * first buffer sample. |
| */ |
| |
| u32 flags; |
| /* Bitfield of flags. |
| * Supported values for bit 31: |
| * - 1 -- Valid timestamp. |
| * - 0 -- Invalid timestamp. |
| * - Use #ASM_BIT_MASKIMESTAMP_VALID_FLAG as the bitmask and |
| * #ASM_SHIFTIMESTAMP_VALID_FLAG as the shift value to set this bit. |
| * Supported values for bit 30: |
| * - 1 -- Last buffer. |
| * - 0 -- Not the last buffer. |
| * |
| * Supported values for bit 29: |
| * - 1 -- Continue the timestamp from the previous buffer. |
| * - 0 -- Timestamp of the current buffer is not related |
| * to the timestamp of the previous buffer. |
| * - Use #ASM_BIT_MASKS_CONTINUE_FLAG and #ASM_SHIFTS_CONTINUE_FLAG |
| * to set this bit. |
| * |
| * Supported values for bit 4: |
| * - 1 -- End of the frame. |
| * - 0 -- Not the end of frame, or this information is not known. |
| * - Use #ASM_BIT_MASK_EOF_FLAG as the bitmask and #ASM_SHIFT_EOF_FLAG |
| * as the shift value to set this bit. |
| * |
| * All other bits are reserved and must be set to 0. |
| * |
| * If bit 31=0 and bit 29=1: The timestamp of the first sample in |
| * this buffer continues from the timestamp of the last sample in |
| * the previous buffer. If there is no previous buffer (i.e., this |
| * is the first buffer sent after opening the stream or after a |
| * flush operation), or if the previous buffer does not have a valid |
| * timestamp, the samples in the current buffer also do not have a |
| * valid timestamp. They are played out as soon as possible. |
| * |
| * |
| * If bit 31=0 and bit 29=0: No timestamp is associated with the |
| * first sample in this buffer. The samples are played out as soon |
| * as possible. |
| * |
| * |
| * If bit 31=1 and bit 29 is ignored: The timestamp specified in |
| * this payload is honored. |
| * |
| * |
| * If bit 30=0: Not the last buffer in the stream. This is useful |
| * in removing trailing samples. |
| * |
| * |
| * For bit 4: The client can set this flag for every buffer sent in |
| * which the last byte is the end of a frame. If this flag is set, |
| * the buffer can contain data from multiple frames, but it should |
| * always end at a frame boundary. Restrictions allow the aDSP to |
| * detect an end of frame without requiring additional processing. |
| */ |
| |
| } __packed; |
| |
| #define ASM_DATA_CMD_READ_V2 0x00010DAC |
| |
| struct asm_data_cmd_read_v2 { |
| struct apr_hdr hdr; |
| u32 buf_addr_lsw; |
| /* the 64 bit address msw-lsw should be a valid mapped address |
| * and should be a multiple of 32 bytes |
| */ |
| |
| |
| u32 buf_addr_msw; |
| /* the 64 bit address msw-lsw should be a valid mapped address |
| * and should be a multiple of 32 bytes. |
| * - Address of the buffer where the DSP puts the encoded data, |
| * potentially, at an offset specified by the uOffset field in |
| * ASM_DATA_EVENT_READ_DONE structure. The buffer should be aligned |
| * to a 32 byte boundary. |
| * - In the case of 32 bit Shared memory address, msw field must |
| * - be set to zero. |
| * - In the case of 36 bit shared memory address, bit 31 to bit |
| * - 4 of msw must be set to zero. |
| */ |
| u32 mem_map_handle; |
| /* memory map handle returned by DSP through |
| * ASM_CMD_SHARED_MEM_MAP_REGIONS command. |
| */ |
| |
| u32 buf_size; |
| /* Number of bytes available for the aDSP to write. The aDSP |
| * starts writing from buf_addr. |
| */ |
| |
| u32 seq_id; |
| /* Optional buffer sequence ID. */ |
| } __packed; |
| |
| #define ASM_DATA_CMD_EOS 0x00010BDB |
| #define ASM_DATA_EVENT_RENDERED_EOS 0x00010C1C |
| #define ASM_DATA_EVENT_EOS 0x00010BDD |
| |
| #define ASM_DATA_EVENT_WRITE_DONE_V2 0x00010D99 |
| struct asm_data_event_write_done_v2 { |
| u32 buf_addr_lsw; |
| /* lsw of the 64 bit address */ |
| u32 buf_addr_msw; |
| /* msw of the 64 bit address. address given by the client in |
| * ASM_DATA_CMD_WRITE_V2 command. |
| */ |
| u32 mem_map_handle; |
| /* memory map handle in the ASM_DATA_CMD_WRITE_V2 */ |
| |
| u32 status; |
| /* Status message (error code) that indicates whether the |
| * referenced buffer has been successfully consumed. |
| * Supported values: Refer to @xhyperref{Q3,[Q3]} |
| */ |
| } __packed; |
| |
| #define ASM_DATA_EVENT_READ_DONE_V2 0x00010D9A |
| |
| /* Definition of the frame metadata flag bitmask.*/ |
| #define ASM_BIT_MASK_FRAME_METADATA_FLAG (0x40000000UL) |
| |
| /* Definition of the frame metadata flag shift value. */ |
| #define ASM_SHIFT_FRAME_METADATA_FLAG 30 |
| |
| struct asm_data_event_read_done_v2 { |
| u32 status; |
| /* Status message (error code). |
| * Supported values: Refer to @xhyperref{Q3,[Q3]} |
| */ |
| |
| u32 buf_addr_lsw; |
| /* 64 bit address msw-lsw is a valid, mapped address. 64 bit |
| * address is a multiple of 32 bytes. |
| */ |
| |
| u32 buf_addr_msw; |
| /* 64 bit address msw-lsw is a valid, mapped address. 64 bit |
| * address is a multiple of 32 bytes. |
| * |
| * -Same address provided by the client in ASM_DATA_CMD_READ_V2 |
| * -In the case of 32 bit Shared memory address, msw field is set to |
| * zero. |
| * -In the case of 36 bit shared memory address, bit 31 to bit 4 |
| * -of msw is set to zero. |
| */ |
| |
| u32 mem_map_handle; |
| /* memory map handle in the ASM_DATA_CMD_READ_V2 */ |
| |
| u32 enc_framesotal_size; |
| /* Total size of the encoded frames in bytes. |
| * Supported values: >0 |
| */ |
| |
| u32 offset; |
| /* Offset (from buf_addr) to the first byte of the first encoded |
| * frame. All encoded frames are consecutive, starting from this |
| * offset. |
| * Supported values: > 0 |
| */ |
| |
| u32 timestamp_lsw; |
| /* Lower 32 bits of the 64-bit session time in microseconds of |
| * the first sample in the buffer. If Bit 5 of mode_flags flag of |
| * ASM_STREAM_CMD_OPEN_READ_V2 is 1 then the 64 bit timestamp is |
| * absolute capture time otherwise it is relative session time. The |
| * absolute timestamp doesn't reset unless the system is reset. |
| */ |
| |
| |
| u32 timestamp_msw; |
| /* Upper 32 bits of the 64-bit session time in microseconds of |
| * the first sample in the buffer. |
| */ |
| |
| |
| u32 flags; |
| /* Bitfield of flags. Bit 30 indicates whether frame metadata is |
| * present. If frame metadata is present, num_frames consecutive |
| * instances of @xhyperref{hdr:FrameMetaData,Frame metadata} start |
| * at the buffer address. |
| * Supported values for bit 31: |
| * - 1 -- Timestamp is valid. |
| * - 0 -- Timestamp is invalid. |
| * - Use #ASM_BIT_MASKIMESTAMP_VALID_FLAG and |
| * #ASM_SHIFTIMESTAMP_VALID_FLAG to set this bit. |
| * |
| * Supported values for bit 30: |
| * - 1 -- Frame metadata is present. |
| * - 0 -- Frame metadata is absent. |
| * - Use #ASM_BIT_MASK_FRAME_METADATA_FLAG and |
| * #ASM_SHIFT_FRAME_METADATA_FLAG to set this bit. |
| * |
| * All other bits are reserved; the aDSP sets them to 0. |
| */ |
| |
| u32 num_frames; |
| /* Number of encoded frames in the buffer. */ |
| |
| u32 seq_id; |
| /* Optional buffer sequence ID. */ |
| } __packed; |
| |
| struct asm_data_read_buf_metadata_v2 { |
| u32 offset; |
| /* Offset from buf_addr in #ASM_DATA_EVENT_READ_DONE_PAYLOAD to |
| * the frame associated with this metadata. |
| * Supported values: > 0 |
| */ |
| |
| u32 frm_size; |
| /* Size of the encoded frame in bytes. |
| * Supported values: > 0 |
| */ |
| |
| u32 num_encoded_pcm_samples; |
| /* Number of encoded PCM samples (per channel) in the frame |
| * associated with this metadata. |
| * Supported values: > 0 |
| */ |
| |
| u32 timestamp_lsw; |
| /* Lower 32 bits of the 64-bit session time in microseconds of the |
| * first sample for this frame. |
| * If Bit 5 of mode_flags flag of ASM_STREAM_CMD_OPEN_READ_V2 is 1 |
| * then the 64 bit timestamp is absolute capture time otherwise it |
| * is relative session time. The absolute timestamp doesn't reset |
| * unless the system is reset. |
| */ |
| |
| |
| u32 timestamp_msw; |
| /* Lower 32 bits of the 64-bit session time in microseconds of the |
| * first sample for this frame. |
| */ |
| |
| u32 flags; |
| /* Frame flags. |
| * Supported values for bit 31: |
| * - 1 -- Time stamp is valid |
| * - 0 -- Time stamp is not valid |
| * - All other bits are reserved; the aDSP sets them to 0. |
| */ |
| } __packed; |
| |
| /* Notifies the client of a change in the data sampling rate or |
| * Channel mode. This event is raised by the decoder service. The |
| * event is enabled through the mode flags of |
| * #ASM_STREAM_CMD_OPEN_WRITE_V2 or |
| * #ASM_STREAM_CMD_OPEN_READWRITE_V2. - The decoder detects a change |
| * in the output sampling frequency or the number/positioning of |
| * output channels, or if it is the first frame decoded.The new |
| * sampling frequency or the new channel configuration is |
| * communicated back to the client asynchronously. |
| */ |
| |
| #define ASM_DATA_EVENT_SR_CM_CHANGE_NOTIFY 0x00010C65 |
| |
| /* Payload of the #ASM_DATA_EVENT_SR_CM_CHANGE_NOTIFY event. |
| * This event is raised when the following conditions are both true: |
| * - The event is enabled through the mode_flags of |
| * #ASM_STREAM_CMD_OPEN_WRITE_V2 or |
| * #ASM_STREAM_CMD_OPEN_READWRITE_V2. - The decoder detects a change |
| * in either the output sampling frequency or the number/positioning |
| * of output channels, or if it is the first frame decoded. |
| * This event is not raised (even if enabled) if the decoder is |
| * MIDI, because |
| */ |
| |
| |
| struct asm_data_event_sr_cm_change_notify { |
| u32 sample_rate; |
| /* New sampling rate (in Hertz) after detecting a change in the |
| * bitstream. |
| * Supported values: 2000 to 48000 |
| */ |
| |
| u16 num_channels; |
| /* New number of channels after detecting a change in the |
| * bitstream. |
| * Supported values: 1 to 8 |
| */ |
| |
| |
| u16 reserved; |
| /* Reserved for future use. This field must be set to 0.*/ |
| |
| u8 channel_mapping[8]; |
| |
| } __packed; |
| |
| /* Notifies the client of a data sampling rate or channel mode |
| * change. This event is raised by the encoder service. |
| * This event is raised when : |
| * - Native mode encoding was requested in the encoder |
| * configuration (i.e., the channel number was 0), the sample rate |
| * was 0, or both were 0. |
| * |
| * - The input data frame at the encoder is the first one, or the |
| * sampling rate/channel mode is different from the previous input |
| * data frame. |
| * |
| */ |
| #define ASM_DATA_EVENT_ENC_SR_CM_CHANGE_NOTIFY 0x00010BDE |
| |
| struct asm_data_event_enc_sr_cm_change_notify { |
| u32 sample_rate; |
| /* New sampling rate (in Hertz) after detecting a change in the |
| * input data. |
| * Supported values: 2000 to 48000 |
| */ |
| |
| |
| u16 num_channels; |
| /* New number of channels after detecting a change in the input |
| * data. Supported values: 1 to 8 |
| */ |
| |
| |
| u16 bits_per_sample; |
| /* New bits per sample after detecting a change in the input |
| * data. |
| * Supported values: 16, 24 |
| */ |
| |
| |
| u8 channel_mapping[8]; |
| |
| } __packed; |
| #define ASM_DATA_CMD_IEC_60958_FRAME_RATE 0x00010D87 |
| |
| |
| /* Payload of the #ASM_DATA_CMD_IEC_60958_FRAME_RATE command, |
| * which is used to indicate the IEC 60958 frame rate of a given |
| * packetized audio stream. |
| */ |
| |
| struct asm_data_cmd_iec_60958_frame_rate { |
| u32 frame_rate; |
| /* IEC 60958 frame rate of the incoming IEC 61937 packetized stream. |
| * Supported values: Any valid frame rate |
| */ |
| } __packed; |
| |
| /* adsp_asm_data_commands.h*/ |
| /* Definition of the stream ID bitmask.*/ |
| #define ASM_BIT_MASK_STREAM_ID (0x000000FFUL) |
| |
| /* Definition of the stream ID shift value.*/ |
| #define ASM_SHIFT_STREAM_ID 0 |
| |
| /* Definition of the session ID bitmask.*/ |
| #define ASM_BIT_MASK_SESSION_ID (0x0000FF00UL) |
| |
| /* Definition of the session ID shift value.*/ |
| #define ASM_SHIFT_SESSION_ID 8 |
| |
| /* Definition of the service ID bitmask.*/ |
| #define ASM_BIT_MASK_SERVICE_ID (0x00FF0000UL) |
| |
| /* Definition of the service ID shift value.*/ |
| #define ASM_SHIFT_SERVICE_ID 16 |
| |
| /* Definition of the domain ID bitmask.*/ |
| #define ASM_BIT_MASK_DOMAIN_ID (0xFF000000UL) |
| |
| /* Definition of the domain ID shift value.*/ |
| #define ASM_SHIFT_DOMAIN_ID 24 |
| |
| #define ASM_CMD_SHARED_MEM_MAP_REGIONS 0x00010D92 |
| #define ASM_CMDRSP_SHARED_MEM_MAP_REGIONS 0x00010D93 |
| #define ASM_CMD_SHARED_MEM_UNMAP_REGIONS 0x00010D94 |
| |
| /* adsp_asm_service_commands.h */ |
| |
| #define ASM_MAX_SESSION_ID (15) |
| |
| /* Maximum number of sessions.*/ |
| #define ASM_MAX_NUM_SESSIONS ASM_MAX_SESSION_ID |
| |
| /* Maximum number of streams per session.*/ |
| #define ASM_MAX_STREAMS_PER_SESSION (8) |
| #define ASM_SESSION_CMD_RUN_V2 0x00010DAA |
| #define ASM_SESSION_CMD_RUN_STARTIME_RUN_IMMEDIATE 0 |
| #define ASM_SESSION_CMD_RUN_STARTIME_RUN_AT_ABSOLUTEIME 1 |
| #define ASM_SESSION_CMD_RUN_STARTIME_RUN_AT_RELATIVEIME 2 |
| #define ASM_SESSION_CMD_RUN_STARTIME_RUN_WITH_DELAY 3 |
| |
| #define ASM_BIT_MASK_RUN_STARTIME (0x00000003UL) |
| |
| /* Bit shift value used to specify the start time for the |
| * ASM_SESSION_CMD_RUN_V2 command. |
| */ |
| #define ASM_SHIFT_RUN_STARTIME 0 |
| struct asm_session_cmd_run_v2 { |
| struct apr_hdr hdr; |
| u32 flags; |
| /* Specifies whether to run immediately or at a specific |
| * rendering time or with a specified delay. Run with delay is |
| * useful for delaying in case of ASM loopback opened through |
| * ASM_STREAM_CMD_OPEN_LOOPBACK_V2. Use #ASM_BIT_MASK_RUN_STARTIME |
| * and #ASM_SHIFT_RUN_STARTIME to set this 2-bit flag. |
| * |
| * |
| *Bits 0 and 1 can take one of four possible values: |
| * |
| *- #ASM_SESSION_CMD_RUN_STARTIME_RUN_IMMEDIATE |
| *- #ASM_SESSION_CMD_RUN_STARTIME_RUN_AT_ABSOLUTEIME |
| *- #ASM_SESSION_CMD_RUN_STARTIME_RUN_AT_RELATIVEIME |
| *- #ASM_SESSION_CMD_RUN_STARTIME_RUN_WITH_DELAY |
| * |
| *All other bits are reserved; clients must set them to zero. |
| */ |
| |
| u32 time_lsw; |
| /* Lower 32 bits of the time in microseconds used to align the |
| * session origin time. When bits 0-1 of flags is |
| * ASM_SESSION_CMD_RUN_START_RUN_WITH_DELAY, time lsw is the lsw of |
| * the delay in us. For ASM_SESSION_CMD_RUN_START_RUN_WITH_DELAY, |
| * maximum value of the 64 bit delay is 150 ms. |
| */ |
| |
| u32 time_msw; |
| /* Upper 32 bits of the time in microseconds used to align the |
| * session origin time. When bits 0-1 of flags is |
| * ASM_SESSION_CMD_RUN_START_RUN_WITH_DELAY, time msw is the msw of |
| * the delay in us. For ASM_SESSION_CMD_RUN_START_RUN_WITH_DELAY, |
| * maximum value of the 64 bit delay is 150 ms. |
| */ |
| |
| } __packed; |
| |
| #define ASM_SESSION_CMD_PAUSE 0x00010BD3 |
| #define ASM_SESSION_CMD_SUSPEND 0x00010DEC |
| #define ASM_SESSION_CMD_GET_SESSIONTIME_V3 0x00010D9D |
| #define ASM_SESSION_CMD_REGISTER_FOR_RX_UNDERFLOW_EVENTS 0x00010BD5 |
| |
| struct asm_session_cmd_rgstr_rx_underflow { |
| struct apr_hdr hdr; |
| u16 enable_flag; |
| /* Specifies whether a client is to receive events when an Rx |
| * session underflows. |
| * Supported values: |
| * - 0 -- Do not send underflow events |
| * - 1 -- Send underflow events |
| */ |
| u16 reserved; |
| /* Reserved. This field must be set to zero.*/ |
| } __packed; |
| |
| #define ASM_SESSION_CMD_REGISTER_FORX_OVERFLOW_EVENTS 0x00010BD6 |
| |
| struct asm_session_cmd_regx_overflow { |
| struct apr_hdr hdr; |
| u16 enable_flag; |
| /* Specifies whether a client is to receive events when a Tx |
| * session overflows. |
| * Supported values: |
| * - 0 -- Do not send overflow events |
| * - 1 -- Send overflow events |
| */ |
| |
| u16 reserved; |
| /* Reserved. This field must be set to zero.*/ |
| } __packed; |
| |
| #define ASM_SESSION_EVENT_RX_UNDERFLOW 0x00010C17 |
| #define ASM_SESSION_EVENTX_OVERFLOW 0x00010C18 |
| #define ASM_SESSION_CMDRSP_GET_SESSIONTIME_V3 0x00010D9E |
| |
| struct asm_session_cmdrsp_get_sessiontime_v3 { |
| u32 status; |
| /* Status message (error code). |
| * Supported values: Refer to @xhyperref{Q3,[Q3]} |
| */ |
| |
| u32 sessiontime_lsw; |
| /* Lower 32 bits of the current session time in microseconds.*/ |
| |
| u32 sessiontime_msw; |
| /* Upper 32 bits of the current session time in microseconds.*/ |
| |
| u32 absolutetime_lsw; |
| /* Lower 32 bits in micro seconds of the absolute time at which |
| * the * sample corresponding to the above session time gets |
| * rendered * to hardware. This absolute time may be slightly in the |
| * future or past. |
| */ |
| |
| |
| u32 absolutetime_msw; |
| /* Upper 32 bits in micro seconds of the absolute time at which |
| * the * sample corresponding to the above session time gets |
| * rendered to * hardware. This absolute time may be slightly in the |
| * future or past. |
| */ |
| |
| } __packed; |
| |
| #define ASM_SESSION_CMD_ADJUST_SESSION_CLOCK_V2 0x00010D9F |
| |
| struct asm_session_cmd_adjust_session_clock_v2 { |
| struct apr_hdr hdr; |
| u32 adjustime_lsw; |
| /* Lower 32 bits of the signed 64-bit quantity that specifies the |
| * adjustment time in microseconds to the session clock. |
| * |
| * Positive values indicate advancement of the session clock. |
| * Negative values indicate delay of the session clock. |
| */ |
| |
| |
| u32 adjustime_msw; |
| /* Upper 32 bits of the signed 64-bit quantity that specifies |
| * the adjustment time in microseconds to the session clock. |
| * Positive values indicate advancement of the session clock. |
| * Negative values indicate delay of the session clock. |
| */ |
| |
| } __packed; |
| |
| #define ASM_SESSION_CMDRSP_ADJUST_SESSION_CLOCK_V2 0x00010DA0 |
| |
| struct asm_session_cmdrsp_adjust_session_clock_v2 { |
| u32 status; |
| /* Status message (error code). |
| * Supported values: Refer to @xhyperref{Q3,[Q3]} |
| * An error means the session clock is not adjusted. In this case, |
| * the next two fields are irrelevant. |
| */ |
| |
| |
| u32 actual_adjustime_lsw; |
| /* Lower 32 bits of the signed 64-bit quantity that specifies |
| * the actual adjustment in microseconds performed by the aDSP. |
| * A positive value indicates advancement of the session clock. A |
| * negative value indicates delay of the session clock. |
| */ |
| |
| |
| u32 actual_adjustime_msw; |
| /* Upper 32 bits of the signed 64-bit quantity that specifies |
| * the actual adjustment in microseconds performed by the aDSP. |
| * A positive value indicates advancement of the session clock. A |
| * negative value indicates delay of the session clock. |
| */ |
| |
| |
| u32 cmd_latency_lsw; |
| /* Lower 32 bits of the unsigned 64-bit quantity that specifies |
| * the amount of time in microseconds taken to perform the session |
| * clock adjustment. |
| */ |
| |
| |
| u32 cmd_latency_msw; |
| /* Upper 32 bits of the unsigned 64-bit quantity that specifies |
| * the amount of time in microseconds taken to perform the session |
| * clock adjustment. |
| */ |
| |
| } __packed; |
| |
| #define ASM_SESSION_CMD_GET_PATH_DELAY_V2 0x00010DAF |
| #define ASM_SESSION_CMDRSP_GET_PATH_DELAY_V2 0x00010DB0 |
| |
| struct asm_session_cmdrsp_get_path_delay_v2 { |
| u32 status; |
| /* Status message (error code). Whether this get delay operation |
| * is successful or not. Delay value is valid only if status is |
| * success. |
| * Supported values: Refer to @xhyperref{Q5,[Q5]} |
| */ |
| |
| u32 audio_delay_lsw; |
| /* Upper 32 bits of the aDSP delay in microseconds. */ |
| |
| u32 audio_delay_msw; |
| /* Lower 32 bits of the aDSP delay in microseconds. */ |
| |
| } __packed; |
| |
| /* adsp_asm_session_command.h*/ |
| #define ASM_STREAM_CMD_OPEN_WRITE_V3 0x00010DB3 |
| |
| #define ASM_LOW_LATENCY_STREAM_SESSION 0x10000000 |
| |
| #define ASM_ULTRA_LOW_LATENCY_STREAM_SESSION 0x20000000 |
| |
| #define ASM_ULL_POST_PROCESSING_STREAM_SESSION 0x40000000 |
| |
| #define ASM_LEGACY_STREAM_SESSION 0 |
| |
| |
| struct asm_stream_cmd_open_write_v3 { |
| struct apr_hdr hdr; |
| uint32_t mode_flags; |
| /* Mode flags that configure the stream to notify the client |
| * whenever it detects an SR/CM change at the input to its POPP. |
| * Supported values for bits 0 to 1: |
| * - Reserved; clients must set them to zero. |
| * Supported values for bit 2: |
| * - 0 -- SR/CM change notification event is disabled. |
| * - 1 -- SR/CM change notification event is enabled. |
| * - Use #ASM_BIT_MASK_SR_CM_CHANGE_NOTIFY_FLAG and |
| * #ASM_SHIFT_SR_CM_CHANGE_NOTIFY_FLAG to set or get this bit. |
| * |
| * Supported values for bit 31: |
| * - 0 -- Stream to be opened in on-Gapless mode. |
| * - 1 -- Stream to be opened in Gapless mode. In Gapless mode, |
| * successive streams must be opened with same session ID but |
| * different stream IDs. |
| * |
| * - Use #ASM_BIT_MASK_GAPLESS_MODE_FLAG and |
| * #ASM_SHIFT_GAPLESS_MODE_FLAG to set or get this bit. |
| * |
| * |
| * @note1hang MIDI and DTMF streams cannot be opened in Gapless mode. |
| */ |
| |
| uint16_t sink_endpointype; |
| /*< Sink point type. |
| * Supported values: |
| * - 0 -- Device matrix |
| * - Other values are reserved. |
| * |
| * The device matrix is the gateway to the hardware ports. |
| */ |
| |
| uint16_t bits_per_sample; |
| /*< Number of bits per sample processed by ASM modules. |
| * Supported values: 16 and 24 bits per sample |
| */ |
| |
| uint32_t postprocopo_id; |
| /*< Specifies the topology (order of processing) of |
| * postprocessing algorithms. <i>None</i> means no postprocessing. |
| * Supported values: |
| * - #ASM_STREAM_POSTPROCOPO_ID_DEFAULT |
| * - #ASM_STREAM_POSTPROCOPO_ID_MCH_PEAK_VOL |
| * - #ASM_STREAM_POSTPROCOPO_ID_NONE |
| * |
| * This field can also be enabled through SetParams flags. |
| */ |
| |
| uint32_t dec_fmt_id; |
| /*< Configuration ID of the decoder media format. |
| * |
| * Supported values: |
| * - #ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V2 |
| * - #ASM_MEDIA_FMT_ADPCM |
| * - #ASM_MEDIA_FMT_MP3 |
| * - #ASM_MEDIA_FMT_AAC_V2 |
| * - #ASM_MEDIA_FMT_DOLBY_AAC |
| * - #ASM_MEDIA_FMT_AMRNB_FS |
| * - #ASM_MEDIA_FMT_AMRWB_FS |
| * - #ASM_MEDIA_FMT_AMR_WB_PLUS_V2 |
| * - #ASM_MEDIA_FMT_V13K_FS |
| * - #ASM_MEDIA_FMT_EVRC_FS |
| * - #ASM_MEDIA_FMT_EVRCB_FS |
| * - #ASM_MEDIA_FMT_EVRCWB_FS |
| * - #ASM_MEDIA_FMT_SBC |
| * - #ASM_MEDIA_FMT_WMA_V10PRO_V2 |
| * - #ASM_MEDIA_FMT_WMA_V9_V2 |
| * - #ASM_MEDIA_FMT_AC3 |
| * - #ASM_MEDIA_FMT_EAC3 |
| * - #ASM_MEDIA_FMT_G711_ALAW_FS |
| * - #ASM_MEDIA_FMT_G711_MLAW_FS |
| * - #ASM_MEDIA_FMT_G729A_FS |
| * - #ASM_MEDIA_FMT_FR_FS |
| * - #ASM_MEDIA_FMT_VORBIS |
| * - #ASM_MEDIA_FMT_FLAC |
| * - #ASM_MEDIA_FMT_ALAC |
| * - #ASM_MEDIA_FMT_APE |
| * - #ASM_MEDIA_FMT_EXAMPLE |
| */ |
| } __packed; |
| |
| #define ASM_STREAM_CMD_OPEN_PULL_MODE_WRITE 0x00010DD9 |
| |
| /* Bitmask for the stream_perf_mode subfield. */ |
| #define ASM_BIT_MASK_STREAM_PERF_FLAG_PULL_MODE_WRITE 0xE0000000UL |
| |
| /* Bitmask for the stream_perf_mode subfield. */ |
| #define ASM_SHIFT_STREAM_PERF_FLAG_PULL_MODE_WRITE 29 |
| |
| #define ASM_STREAM_CMD_OPEN_PUSH_MODE_READ 0x00010DDA |
| |
| #define ASM_BIT_MASK_STREAM_PERF_FLAG_PUSH_MODE_READ 0xE0000000UL |
| |
| #define ASM_SHIFT_STREAM_PERF_FLAG_PUSH_MODE_READ 29 |
| |
| #define ASM_DATA_EVENT_WATERMARK 0x00010DDB |
| |
| struct asm_shared_position_buffer { |
| volatile uint32_t frame_counter; |
| /* Counter used to handle interprocessor synchronization issues. |
| * When frame_counter is 0: read_index, wall_clock_us_lsw, and |
| * wall_clock_us_msw are invalid. |
| * Supported values: >= 0. |
| */ |
| |
| volatile uint32_t index; |
| /* Index in bytes from where the aDSP is reading/writing. |
| * Supported values: 0 to circular buffer size - 1 |
| */ |
| |
| volatile uint32_t wall_clock_us_lsw; |
| /* Lower 32 bits of the 64-bit wall clock time in microseconds when the |
| * read index was updated. |
| * Supported values: >= 0 |
| */ |
| |
| volatile uint32_t wall_clock_us_msw; |
| /* Upper 32 bits of the 64 bit wall clock time in microseconds when the |
| * read index was updated |
| * Supported values: >= 0 |
| */ |
| } __packed; |
| |
| struct asm_shared_watermark_level { |
| uint32_t watermark_level_bytes; |
| } __packed; |
| |
| struct asm_stream_cmd_open_shared_io { |
| struct apr_hdr hdr; |
| uint32_t mode_flags; |
| uint16_t endpoint_type; |
| uint16_t topo_bits_per_sample; |
| uint32_t topo_id; |
| uint32_t fmt_id; |
| uint32_t shared_pos_buf_phy_addr_lsw; |
| uint32_t shared_pos_buf_phy_addr_msw; |
| uint16_t shared_pos_buf_mem_pool_id; |
| uint16_t shared_pos_buf_num_regions; |
| uint32_t shared_pos_buf_property_flag; |
| uint32_t shared_circ_buf_start_phy_addr_lsw; |
| uint32_t shared_circ_buf_start_phy_addr_msw; |
| uint32_t shared_circ_buf_size; |
| uint16_t shared_circ_buf_mem_pool_id; |
| uint16_t shared_circ_buf_num_regions; |
| uint32_t shared_circ_buf_property_flag; |
| uint32_t num_watermark_levels; |
| struct asm_multi_channel_pcm_fmt_blk_v3 fmt; |
| struct avs_shared_map_region_payload map_region_pos_buf; |
| struct avs_shared_map_region_payload map_region_circ_buf; |
| struct asm_shared_watermark_level watermark[0]; |
| } __packed; |
| |
| #define ASM_STREAM_CMD_OPEN_READ_V3 0x00010DB4 |
| |
| /* Definition of the timestamp type flag bitmask */ |
| #define ASM_BIT_MASKIMESTAMPYPE_FLAG (0x00000020UL) |
| |
| /* Definition of the timestamp type flag shift value. */ |
| #define ASM_SHIFTIMESTAMPYPE_FLAG 5 |
| |
| /* Relative timestamp is identified by this value.*/ |
| #define ASM_RELATIVEIMESTAMP 0 |
| |
| /* Absolute timestamp is identified by this value.*/ |
| #define ASM_ABSOLUTEIMESTAMP 1 |
| |
| /* Bit value for Low Latency Tx stream subfield */ |
| #define ASM_LOW_LATENCY_TX_STREAM_SESSION 1 |
| |
| /* Bit shift for the stream_perf_mode subfield. */ |
| #define ASM_SHIFT_STREAM_PERF_MODE_FLAG_IN_OPEN_READ 29 |
| |
| struct asm_stream_cmd_open_read_v3 { |
| struct apr_hdr hdr; |
| u32 mode_flags; |
| /* Mode flags that indicate whether meta information per encoded |
| * frame is to be provided. |
| * Supported values for bit 4: |
| * |
| * - 0 -- Return data buffer contains all encoded frames only; it |
| * does not contain frame metadata. |
| * |
| * - 1 -- Return data buffer contains an array of metadata and |
| * encoded frames. |
| * |
| * - Use #ASM_BIT_MASK_META_INFO_FLAG as the bitmask and |
| * #ASM_SHIFT_META_INFO_FLAG as the shift value for this bit. |
| * |
| * |
| * Supported values for bit 5: |
| * |
| * - ASM_RELATIVEIMESTAMP -- ASM_DATA_EVENT_READ_DONE_V2 will have |
| * - relative time-stamp. |
| * - ASM_ABSOLUTEIMESTAMP -- ASM_DATA_EVENT_READ_DONE_V2 will |
| * - have absolute time-stamp. |
| * |
| * - Use #ASM_BIT_MASKIMESTAMPYPE_FLAG as the bitmask and |
| * #ASM_SHIFTIMESTAMPYPE_FLAG as the shift value for this bit. |
| * |
| * All other bits are reserved; clients must set them to zero. |
| */ |
| |
| u32 src_endpointype; |
| /* Specifies the endpoint providing the input samples. |
| * Supported values: |
| * - 0 -- Device matrix |
| * - All other values are reserved; clients must set them to zero. |
| * Otherwise, an error is returned. |
| * The device matrix is the gateway from the tunneled Tx ports. |
| */ |
| |
| u32 preprocopo_id; |
| /* Specifies the topology (order of processing) of preprocessing |
| * algorithms. <i>None</i> means no preprocessing. |
| * Supported values: |
| * - #ASM_STREAM_PREPROCOPO_ID_DEFAULT |
| * - #ASM_STREAM_PREPROCOPO_ID_NONE |
| * |
| * This field can also be enabled through SetParams flags. |
| */ |
| |
| u32 enc_cfg_id; |
| /* Media configuration ID for encoded output. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V2 |
| * - #ASM_MEDIA_FMT_AAC_V2 |
| * - #ASM_MEDIA_FMT_AMRNB_FS |
| * - #ASM_MEDIA_FMT_AMRWB_FS |
| * - #ASM_MEDIA_FMT_V13K_FS |
| * - #ASM_MEDIA_FMT_EVRC_FS |
| * - #ASM_MEDIA_FMT_EVRCB_FS |
| * - #ASM_MEDIA_FMT_EVRCWB_FS |
| * - #ASM_MEDIA_FMT_SBC |
| * - #ASM_MEDIA_FMT_G711_ALAW_FS |
| * - #ASM_MEDIA_FMT_G711_MLAW_FS |
| * - #ASM_MEDIA_FMT_G729A_FS |
| * - #ASM_MEDIA_FMT_EXAMPLE |
| * - #ASM_MEDIA_FMT_WMA_V8 |
| */ |
| |
| u16 bits_per_sample; |
| /* Number of bits per sample processed by ASM modules. |
| * Supported values: 16 and 24 bits per sample |
| */ |
| |
| u16 reserved; |
| /* Reserved for future use. This field must be set to zero.*/ |
| } __packed; |
| |
| #define ASM_POPP_OUTPUT_SR_NATIVE_RATE 0 |
| |
| /* Enumeration for the maximum sampling rate at the POPP output.*/ |
| #define ASM_POPP_OUTPUT_SR_MAX_RATE 48000 |
| |
| #define ASM_STREAM_CMD_OPEN_READWRITE_V2 0x00010D8D |
| #define ASM_STREAM_CMD_OPEN_READWRITE_V2 0x00010D8D |
| |
| struct asm_stream_cmd_open_readwrite_v2 { |
| struct apr_hdr hdr; |
| u32 mode_flags; |
| /* Mode flags. |
| * Supported values for bit 2: |
| * - 0 -- SR/CM change notification event is disabled. |
| * - 1 -- SR/CM change notification event is enabled. Use |
| * #ASM_BIT_MASK_SR_CM_CHANGE_NOTIFY_FLAG and |
| * #ASM_SHIFT_SR_CM_CHANGE_NOTIFY_FLAG to set or |
| * getting this flag. |
| * |
| * Supported values for bit 4: |
| * - 0 -- Return read data buffer contains all encoded frames only; it |
| * does not contain frame metadata. |
| * - 1 -- Return read data buffer contains an array of metadata and |
| * encoded frames. |
| * |
| * All other bits are reserved; clients must set them to zero. |
| */ |
| |
| u32 postprocopo_id; |
| /* Specifies the topology (order of processing) of postprocessing |
| * algorithms. <i>None</i> means no postprocessing. |
| * |
| * Supported values: |
| * - #ASM_STREAM_POSTPROCOPO_ID_DEFAULT |
| * - #ASM_STREAM_POSTPROCOPO_ID_MCH_PEAK_VOL |
| * - #ASM_STREAM_POSTPROCOPO_ID_NONE |
| */ |
| |
| u32 dec_fmt_id; |
| /* Specifies the media type of the input data. PCM indicates that |
| * no decoding must be performed, e.g., this is an NT encoder |
| * session. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V2 |
| * - #ASM_MEDIA_FMT_ADPCM |
| * - #ASM_MEDIA_FMT_MP3 |
| * - #ASM_MEDIA_FMT_AAC_V2 |
| * - #ASM_MEDIA_FMT_DOLBY_AAC |
| * - #ASM_MEDIA_FMT_AMRNB_FS |
| * - #ASM_MEDIA_FMT_AMRWB_FS |
| * - #ASM_MEDIA_FMT_V13K_FS |
| * - #ASM_MEDIA_FMT_EVRC_FS |
| * - #ASM_MEDIA_FMT_EVRCB_FS |
| * - #ASM_MEDIA_FMT_EVRCWB_FS |
| * - #ASM_MEDIA_FMT_SBC |
| * - #ASM_MEDIA_FMT_WMA_V10PRO_V2 |
| * - #ASM_MEDIA_FMT_WMA_V9_V2 |
| * - #ASM_MEDIA_FMT_AMR_WB_PLUS_V2 |
| * - #ASM_MEDIA_FMT_AC3 |
| * - #ASM_MEDIA_FMT_G711_ALAW_FS |
| * - #ASM_MEDIA_FMT_G711_MLAW_FS |
| * - #ASM_MEDIA_FMT_G729A_FS |
| * - #ASM_MEDIA_FMT_EXAMPLE |
| */ |
| |
| u32 enc_cfg_id; |
| /* Specifies the media type for the output of the stream. PCM |
| * indicates that no encoding must be performed, e.g., this is an NT |
| * decoder session. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V2 |
| * - #ASM_MEDIA_FMT_AAC_V2 |
| * - #ASM_MEDIA_FMT_AMRNB_FS |
| * - #ASM_MEDIA_FMT_AMRWB_FS |
| * - #ASM_MEDIA_FMT_V13K_FS |
| * - #ASM_MEDIA_FMT_EVRC_FS |
| * - #ASM_MEDIA_FMT_EVRCB_FS |
| * - #ASM_MEDIA_FMT_EVRCWB_FS |
| * - #ASM_MEDIA_FMT_SBC |
| * - #ASM_MEDIA_FMT_G711_ALAW_FS |
| * - #ASM_MEDIA_FMT_G711_MLAW_FS |
| * - #ASM_MEDIA_FMT_G729A_FS |
| * - #ASM_MEDIA_FMT_EXAMPLE |
| * - #ASM_MEDIA_FMT_WMA_V8 |
| */ |
| |
| u16 bits_per_sample; |
| /* Number of bits per sample processed by ASM modules. |
| * Supported values: 16 and 24 bits per sample |
| */ |
| |
| u16 reserved; |
| /* Reserved for future use. This field must be set to zero.*/ |
| |
| } __packed; |
| |
| #define ASM_STREAM_CMD_OPEN_LOOPBACK_V2 0x00010D8E |
| struct asm_stream_cmd_open_loopback_v2 { |
| struct apr_hdr hdr; |
| u32 mode_flags; |
| /* Mode flags. |
| * Bit 0-31: reserved; client should set these bits to 0 |
| */ |
| u16 src_endpointype; |
| /* Endpoint type. 0 = Tx Matrix */ |
| u16 sink_endpointype; |
| /* Endpoint type. 0 = Rx Matrix */ |
| u32 postprocopo_id; |
| /* Postprocessor topology ID. Specifies the topology of |
| * postprocessing algorithms. |
| */ |
| |
| u16 bits_per_sample; |
| /* The number of bits per sample processed by ASM modules |
| * Supported values: 16 and 24 bits per sample |
| */ |
| u16 reserved; |
| /* Reserved for future use. This field must be set to zero. */ |
| } __packed; |
| |
| |
| #define ASM_STREAM_CMD_OPEN_TRANSCODE_LOOPBACK 0x00010DBA |
| |
| /* Bitmask for the stream's Performance mode. */ |
| #define ASM_BIT_MASK_STREAM_PERF_MODE_FLAG_IN_OPEN_TRANSCODE_LOOPBACK \ |
| (0x70000000UL) |
| |
| /* Bit shift for the stream's Performance mode. */ |
| #define ASM_SHIFT_STREAM_PERF_MODE_FLAG_IN_OPEN_TRANSCODE_LOOPBACK 28 |
| |
| /* Bitmask for the decoder converter enable flag. */ |
| #define ASM_BIT_MASK_DECODER_CONVERTER_FLAG (0x00000078UL) |
| |
| /* Shift value for the decoder converter enable flag. */ |
| #define ASM_SHIFT_DECODER_CONVERTER_FLAG 3 |
| |
| /* Converter mode is None (Default). */ |
| #define ASM_CONVERTER_MODE_NONE 0 |
| |
| /* Converter mode is DDP-to-DD. */ |
| #define ASM_DDP_DD_CONVERTER_MODE 1 |
| |
| /* Identifies a special converter mode where source and sink formats |
| * are the same but postprocessing must applied. Therefore, Decode |
| * @rarrow Re-encode is necessary. |
| */ |
| #define ASM_POST_PROCESS_CONVERTER_MODE 2 |
| |
| |
| struct asm_stream_cmd_open_transcode_loopback_t { |
| struct apr_hdr hdr; |
| u32 mode_flags; |
| /* Mode Flags specifies the performance mode in which this stream |
| * is to be opened. |
| * Supported values{for bits 30 to 28}(stream_perf_mode flag) |
| * |
| * #ASM_LEGACY_STREAM_SESSION -- This mode ensures backward |
| * compatibility to the original behavior |
| * of ASM_STREAM_CMD_OPEN_TRANSCODE_LOOPBACK |
| * |
| * #ASM_LOW_LATENCY_STREAM_SESSION -- Opens a loopback session by using |
| * shortened buffers in low latency POPP |
| * - Recommendation: Do not enable high latency algorithms. They might |
| * negate the benefits of opening a low latency stream, and they |
| * might also suffer quality degradation from unexpected jitter. |
| * - This Low Latency mode is supported only for PCM In and PCM Out |
| * loopbacks. An error is returned if Low Latency mode is opened for |
| * other transcode loopback modes. |
| * - To configure this subfield, use |
| * ASM_BIT_MASK_STREAM_PERF_MODE_FLAG_IN_OPEN_TRANSCODE_LOOPBACK and |
| * ASM_SHIFT_STREAM_PERF_MODE_FLAG_IN_OPEN_TRANSCODE_LOOPBACK. |
| * |
| * Supported values{for bits 6 to 3} (decoder-converter compatibility) |
| * #ASM_CONVERTER_MODE_NONE (0x0) -- Default |
| * #ASM_DDP_DD_CONVERTER_MODE (0x1) |
| * #ASM_POST_PROCESS_CONVERTER_MODE (0x2) |
| * 0x3-0xF -- Reserved for future use |
| * - Use #ASM_BIT_MASK_DECODER_CONVERTER_FLAG and |
| * ASM_SHIFT_DECODER_CONVERTER_FLAG to set this bit |
| * All other bits are reserved; clients must set them to 0. |
| */ |
| |
| u32 src_format_id; |
| /* Specifies the media format of the input audio stream. |
| * |
| * Supported values |
| * - #ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V2 |
| * - #ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V3 |
| * - #ASM_MEDIA_FMT_DTS |
| * - #ASM_MEDIA_FMT_EAC3_DEC |
| * - #ASM_MEDIA_FMT_EAC3 |
| * - #ASM_MEDIA_FMT_AC3_DEC |
| * - #ASM_MEDIA_FMT_AC3 |
| */ |
| u32 sink_format_id; |
| /* Specifies the media format of the output stream. |
| * |
| * Supported values |
| * - #ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V2 |
| * - #ASM_MEDIA_FMT_MULTI_CHANNEL_PCM_V3 |
| * - #ASM_MEDIA_FMT_DTS (not supported in Low Latency mode) |
| * - #ASM_MEDIA_FMT_EAC3_DEC (not supported in Low Latency mode) |
| * - #ASM_MEDIA_FMT_EAC3 (not supported in Low Latency mode) |
| * - #ASM_MEDIA_FMT_AC3_DEC (not supported in Low Latency mode) |
| * - #ASM_MEDIA_FMT_AC3 (not supported in Low Latency mode) |
| */ |
| |
| u32 audproc_topo_id; |
| /* Postprocessing topology ID, which specifies the topology (order of |
| * processing) of postprocessing algorithms. |
| * |
| * Supported values |
| * - #ASM_STREAM_POSTPROC_TOPO_ID_DEFAULT |
| * - #ASM_STREAM_POSTPROC_TOPO_ID_PEAKMETER |
| * - #ASM_STREAM_POSTPROC_TOPO_ID_MCH_PEAK_VOL |
| * - #ASM_STREAM_POSTPROC_TOPO_ID_NONE |
| * Topologies can be added through #ASM_CMD_ADD_TOPOLOGIES. |
| * This field is ignored for the Converter mode, in which no |
| * postprocessing is performed. |
| */ |
| |
| u16 src_endpoint_type; |
| /* Specifies the source endpoint that provides the input samples. |
| * |
| * Supported values |
| * - 0 -- Tx device matrix or stream router (gateway to the hardware |
| * ports) |
| * - All other values are reserved |
| * Clients must set this field to 0. Otherwise, an error is returned. |
| */ |
| |
| u16 sink_endpoint_type; |
| /* Specifies the sink endpoint type. |
| * |
| * Supported values |
| * - 0 -- Rx device matrix or stream router (gateway to the hardware |
| * ports) |
| * - All other values are reserved |
| * Clients must set this field to 0. Otherwise, an error is returned. |
| */ |
| |
| u16 bits_per_sample; |
| /* Number of bits per sample processed by the ASM modules. |
| * Supported values 16, 24 |
| */ |
| |
| u16 reserved; |
| /* This field must be set to 0. |
| */ |
| } __packed; |
| |
| |
| #define ASM_STREAM_CMD_CLOSE 0x00010BCD |
| #define ASM_STREAM_CMD_FLUSH 0x00010BCE |
| |
| |
| #define ASM_STREAM_CMD_FLUSH_READBUFS 0x00010C09 |
| #define ASM_STREAM_CMD_SET_PP_PARAMS_V2 0x00010DA1 |
| |
| struct asm_stream_cmd_set_pp_params_v2 { |
| u32 data_payload_addr_lsw; |
| /* LSW of parameter data payload address. Supported values: any. */ |
| u32 data_payload_addr_msw; |
| /* MSW of Parameter data payload address. Supported values: any. |
| * - Must be set to zero for in-band data. |
| * - In the case of 32 bit Shared memory address, msw field must be |
| * - set to zero. |
| * - In the case of 36 bit shared memory address, bit 31 to bit 4 of |
| * msw |
| * |
| * - must be set to zero. |
| */ |
| u32 mem_map_handle; |
| /* Supported Values: Any. |
| * memory map handle returned by DSP through |
| * ASM_CMD_SHARED_MEM_MAP_REGIONS |
| * command. |
| * if mmhandle is NULL, the ParamData payloads are within the |
| * message payload (in-band). |
| * If mmhandle is non-NULL, the ParamData payloads begin at the |
| * address specified in the address msw and lsw (out-of-band). |
| */ |
| |
| u32 data_payload_size; |
| /* Size in bytes of the variable payload accompanying the |
| * message, or in shared memory. This field is used for parsing the |
| * parameter payload. |
| */ |
| } __packed; |
| |
| |
| struct asm_stream_param_data_v2 { |
| u32 module_id; |
| /* Unique module ID. */ |
| |
| u32 param_id; |
| /* Unique parameter ID. */ |
| |
| u16 param_size; |
| /* Data size of the param_id/module_id combination. This is |
| * a multiple of 4 bytes. |
| */ |
| |
| u16 reserved; |
| /* Reserved for future enhancements. This field must be set to |
| * zero. |
| */ |
| |
| } __packed; |
| |
| #define ASM_STREAM_CMD_GET_PP_PARAMS_V2 0x00010DA2 |
| |
| struct asm_stream_cmd_get_pp_params_v2 { |
| u32 data_payload_addr_lsw; |
| /* LSW of the parameter data payload address. */ |
| u32 data_payload_addr_msw; |
| /* MSW of the parameter data payload address. |
| * - Size of the shared memory, if specified, shall be large enough |
| * to contain the whole ParamData payload, including Module ID, |
| * Param ID, Param Size, and Param Values |
| * - Must be set to zero for in-band data |
| * - In the case of 32 bit Shared memory address, msw field must be |
| * set to zero. |
| * - In the case of 36 bit shared memory address, bit 31 to bit 4 of |
| * msw must be set to zero. |
| */ |
| |
| u32 mem_map_handle; |
| /* Supported Values: Any. |
| * memory map handle returned by DSP through ASM_CMD_SHARED_MEM_MAP_REGIONS |
| * command. |
| * if mmhandle is NULL, the ParamData payloads in the ACK are within the |
| * message payload (in-band). |
| * If mmhandle is non-NULL, the ParamData payloads in the ACK begin at the |
| * address specified in the address msw and lsw. |
| * (out-of-band). |
| */ |
| |
| u32 module_id; |
| /* Unique module ID. */ |
| |
| u32 param_id; |
| /* Unique parameter ID. */ |
| |
| u16 param_max_size; |
| /* Maximum data size of the module_id/param_id combination. This |
| * is a multiple of 4 bytes. |
| */ |
| |
| |
| u16 reserved; |
| /* Reserved for backward compatibility. Clients must set this |
| * field to zero. |
| */ |
| } __packed; |
| |
| #define ASM_STREAM_CMD_SET_ENCDEC_PARAM 0x00010C10 |
| |
| #define ASM_STREAM_CMD_SET_ENCDEC_PARAM_V2 0x00013218 |
| |
| struct asm_stream_cmd_set_encdec_param_v2 { |
| u16 service_id; |
| /* 0 - ASM_ENCODER_SVC; 1 - ASM_DECODER_SVC */ |
| |
| u16 reserved; |
| |
| u32 param_id; |
| /* ID of the parameter. */ |
| |
| u32 param_size; |
| /* |
| * Data size of this parameter, in bytes. The size is a multiple |
| * of 4 bytes. |
| */ |
| } __packed; |
| |
| #define ASM_STREAM_CMD_REGISTER_ENCDEC_EVENTS 0x00013219 |
| |
| #define ASM_STREAM_CMD_ENCDEC_EVENTS 0x0001321A |
| |
| #define AVS_PARAM_ID_RTIC_SHARED_MEMORY_ADDR 0x00013237 |
| |
| struct avs_rtic_shared_mem_addr { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param_v2 encdec; |
| u32 shm_buf_addr_lsw; |
| /* Lower 32 bit of the RTIC shared memory */ |
| |
| u32 shm_buf_addr_msw; |
| /* Upper 32 bit of the RTIC shared memory */ |
| |
| u32 buf_size; |
| /* Size of buffer */ |
| |
| u16 shm_buf_mem_pool_id; |
| /* ADSP_MEMORY_MAP_SHMEM8_4K_POOL */ |
| |
| u16 shm_buf_num_regions; |
| /* number of regions to map */ |
| |
| u32 shm_buf_flag; |
| /* buffer property flag */ |
| |
| struct avs_shared_map_region_payload map_region; |
| /* memory map region*/ |
| } __packed; |
| |
| #define AVS_PARAM_ID_RTIC_EVENT_ACK 0x00013238 |
| |
| struct avs_param_rtic_event_ack { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param_v2 encdec; |
| } __packed; |
| |
| #define ASM_PARAM_ID_ENCDEC_BITRATE 0x00010C13 |
| |
| struct asm_bitrate_param { |
| u32 bitrate; |
| /* Maximum supported bitrate. Only the AAC encoder is supported.*/ |
| |
| } __packed; |
| |
| #define ASM_PARAM_ID_ENCDEC_ENC_CFG_BLK_V2 0x00010DA3 |
| #define ASM_PARAM_ID_AAC_SBR_PS_FLAG 0x00010C63 |
| |
| /* Flag to turn off both SBR and PS processing, if they are |
| * present in the bitstream. |
| */ |
| |
| #define ASM_AAC_SBR_OFF_PS_OFF (2) |
| |
| /* Flag to turn on SBR but turn off PS processing,if they are |
| * present in the bitstream. |
| */ |
| |
| #define ASM_AAC_SBR_ON_PS_OFF (1) |
| |
| /* Flag to turn on both SBR and PS processing, if they are |
| * present in the bitstream (default behavior). |
| */ |
| |
| |
| #define ASM_AAC_SBR_ON_PS_ON (0) |
| |
| /* Structure for an AAC SBR PS processing flag. */ |
| |
| /* Payload of the #ASM_PARAM_ID_AAC_SBR_PS_FLAG parameter in the |
| * #ASM_STREAM_CMD_SET_ENCDEC_PARAM command. |
| */ |
| struct asm_aac_sbr_ps_flag_param { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| struct asm_enc_cfg_blk_param_v2 encblk; |
| |
| u32 sbr_ps_flag; |
| /* Control parameter to enable or disable SBR/PS processing in |
| * the AAC bitstream. Use the following macros to set this field: |
| * - #ASM_AAC_SBR_OFF_PS_OFF -- Turn off both SBR and PS |
| * processing, if they are present in the bitstream. |
| * - #ASM_AAC_SBR_ON_PS_OFF -- Turn on SBR processing, but not PS |
| * processing, if they are present in the bitstream. |
| * - #ASM_AAC_SBR_ON_PS_ON -- Turn on both SBR and PS processing, |
| * if they are present in the bitstream (default behavior). |
| * - All other values are invalid. |
| * Changes are applied to the next decoded frame. |
| */ |
| } __packed; |
| |
| #define ASM_PARAM_ID_AAC_DUAL_MONO_MAPPING 0x00010C64 |
| |
| /* First single channel element in a dual mono bitstream.*/ |
| #define ASM_AAC_DUAL_MONO_MAP_SCE_1 (1) |
| |
| /* Second single channel element in a dual mono bitstream.*/ |
| #define ASM_AAC_DUAL_MONO_MAP_SCE_2 (2) |
| |
| /* Structure for AAC decoder dual mono channel mapping. */ |
| |
| |
| struct asm_aac_dual_mono_mapping_param { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| u16 left_channel_sce; |
| u16 right_channel_sce; |
| |
| } __packed; |
| |
| #define ASM_STREAM_CMDRSP_GET_PP_PARAMS_V2 0x00010DA4 |
| |
| struct asm_stream_cmdrsp_get_pp_params_v2 { |
| u32 status; |
| } __packed; |
| |
| #define ASM_PARAM_ID_AC3_KARAOKE_MODE 0x00010D73 |
| |
| /* Enumeration for both vocals in a karaoke stream.*/ |
| #define AC3_KARAOKE_MODE_NO_VOCAL (0) |
| |
| /* Enumeration for only the left vocal in a karaoke stream.*/ |
| #define AC3_KARAOKE_MODE_LEFT_VOCAL (1) |
| |
| /* Enumeration for only the right vocal in a karaoke stream.*/ |
| #define AC3_KARAOKE_MODE_RIGHT_VOCAL (2) |
| |
| /* Enumeration for both vocal channels in a karaoke stream.*/ |
| #define AC3_KARAOKE_MODE_BOTH_VOCAL (3) |
| #define ASM_PARAM_ID_AC3_DRC_MODE 0x00010D74 |
| /* Enumeration for the Custom Analog mode.*/ |
| #define AC3_DRC_MODE_CUSTOM_ANALOG (0) |
| |
| /* Enumeration for the Custom Digital mode.*/ |
| #define AC3_DRC_MODE_CUSTOM_DIGITAL (1) |
| /* Enumeration for the Line Out mode (light compression).*/ |
| #define AC3_DRC_MODE_LINE_OUT (2) |
| |
| /* Enumeration for the RF remodulation mode (heavy compression).*/ |
| #define AC3_DRC_MODE_RF_REMOD (3) |
| #define ASM_PARAM_ID_AC3_DUAL_MONO_MODE 0x00010D75 |
| |
| /* Enumeration for playing dual mono in stereo mode.*/ |
| #define AC3_DUAL_MONO_MODE_STEREO (0) |
| |
| /* Enumeration for playing left mono.*/ |
| #define AC3_DUAL_MONO_MODE_LEFT_MONO (1) |
| |
| /* Enumeration for playing right mono.*/ |
| #define AC3_DUAL_MONO_MODE_RIGHT_MONO (2) |
| |
| /* Enumeration for mixing both dual mono channels and playing them.*/ |
| #define AC3_DUAL_MONO_MODE_MIXED_MONO (3) |
| #define ASM_PARAM_ID_AC3_STEREO_DOWNMIX_MODE 0x00010D76 |
| |
| /* Enumeration for using the Downmix mode indicated in the bitstream. */ |
| |
| #define AC3_STEREO_DOWNMIX_MODE_AUTO_DETECT (0) |
| |
| /* Enumeration for Surround Compatible mode (preserves the |
| * surround information). |
| */ |
| |
| #define AC3_STEREO_DOWNMIX_MODE_LT_RT (1) |
| /* Enumeration for Mono Compatible mode (if the output is to be |
| * further downmixed to mono). |
| */ |
| |
| #define AC3_STEREO_DOWNMIX_MODE_LO_RO (2) |
| |
| /* ID of the AC3 PCM scale factor parameter in the |
| * #ASM_STREAM_CMD_SET_ENCDEC_PARAM command. |
| */ |
| #define ASM_PARAM_ID_AC3_PCM_SCALEFACTOR 0x00010D78 |
| |
| /* ID of the AC3 DRC boost scale factor parameter in the |
| * #ASM_STREAM_CMD_SET_ENCDEC_PARAM command. |
| */ |
| #define ASM_PARAM_ID_AC3_DRC_BOOST_SCALEFACTOR 0x00010D79 |
| |
| /* ID of the AC3 DRC cut scale factor parameter in the |
| * #ASM_STREAM_CMD_SET_ENCDEC_PARAM command. |
| */ |
| #define ASM_PARAM_ID_AC3_DRC_CUT_SCALEFACTOR 0x00010D7A |
| |
| /* Structure for AC3 Generic Parameter. */ |
| |
| /* Payload of the AC3 parameters in the |
| * #ASM_STREAM_CMD_SET_ENCDEC_PARAM command. |
| */ |
| struct asm_ac3_generic_param { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| struct asm_enc_cfg_blk_param_v2 encblk; |
| u32 generic_parameter; |
| /* AC3 generic parameter. Select from one of the following |
| * possible values. |
| * |
| * For #ASM_PARAM_ID_AC3_KARAOKE_MODE, supported values are: |
| * - AC3_KARAOKE_MODE_NO_VOCAL |
| * - AC3_KARAOKE_MODE_LEFT_VOCAL |
| * - AC3_KARAOKE_MODE_RIGHT_VOCAL |
| * - AC3_KARAOKE_MODE_BOTH_VOCAL |
| * |
| * For #ASM_PARAM_ID_AC3_DRC_MODE, supported values are: |
| * - AC3_DRC_MODE_CUSTOM_ANALOG |
| * - AC3_DRC_MODE_CUSTOM_DIGITAL |
| * - AC3_DRC_MODE_LINE_OUT |
| * - AC3_DRC_MODE_RF_REMOD |
| * |
| * For #ASM_PARAM_ID_AC3_DUAL_MONO_MODE, supported values are: |
| * - AC3_DUAL_MONO_MODE_STEREO |
| * - AC3_DUAL_MONO_MODE_LEFT_MONO |
| * - AC3_DUAL_MONO_MODE_RIGHT_MONO |
| * - AC3_DUAL_MONO_MODE_MIXED_MONO |
| * |
| * For #ASM_PARAM_ID_AC3_STEREO_DOWNMIX_MODE, supported values are: |
| * - AC3_STEREO_DOWNMIX_MODE_AUTO_DETECT |
| * - AC3_STEREO_DOWNMIX_MODE_LT_RT |
| * - AC3_STEREO_DOWNMIX_MODE_LO_RO |
| * |
| * For #ASM_PARAM_ID_AC3_PCM_SCALEFACTOR, supported values are |
| * 0 to 1 in Q31 format. |
| * |
| * For #ASM_PARAM_ID_AC3_DRC_BOOST_SCALEFACTOR, supported values are |
| * 0 to 1 in Q31 format. |
| * |
| * For #ASM_PARAM_ID_AC3_DRC_CUT_SCALEFACTOR, supported values are |
| * 0 to 1 in Q31 format. |
| */ |
| } __packed; |
| |
| /* Enumeration for Raw mode (no downmixing), which specifies |
| * that all channels in the bitstream are to be played out as is |
| * without any downmixing. (Default) |
| */ |
| |
| #define WMAPRO_CHANNEL_MASK_RAW (-1) |
| |
| /* Enumeration for setting the channel mask to 0. The 7.1 mode |
| * (Home Theater) is assigned. |
| */ |
| |
| |
| #define WMAPRO_CHANNEL_MASK_ZERO 0x0000 |
| |
| /* Speaker layout mask for one channel (Home Theater, mono). |
| * - Speaker front center |
| */ |
| #define WMAPRO_CHANNEL_MASK_1_C 0x0004 |
| |
| /* Speaker layout mask for two channels (Home Theater, stereo). |
| * - Speaker front left |
| * - Speaker front right |
| */ |
| #define WMAPRO_CHANNEL_MASK_2_L_R 0x0003 |
| |
| /* Speaker layout mask for three channels (Home Theater). |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker front center |
| */ |
| #define WMAPRO_CHANNEL_MASK_3_L_C_R 0x0007 |
| |
| /* Speaker layout mask for two channels (stereo). |
| * - Speaker back left |
| * - Speaker back right |
| */ |
| #define WMAPRO_CHANNEL_MASK_2_Bl_Br 0x0030 |
| |
| /* Speaker layout mask for four channels. |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker back left |
| * - Speaker back right |
| */ |
| #define WMAPRO_CHANNEL_MASK_4_L_R_Bl_Br 0x0033 |
| |
| /* Speaker layout mask for four channels (Home Theater). |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker front center |
| * - Speaker back center |
| */ |
| #define WMAPRO_CHANNEL_MASK_4_L_R_C_Bc_HT 0x0107 |
| /* Speaker layout mask for five channels. |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker front center |
| * - Speaker back left |
| * - Speaker back right |
| */ |
| #define WMAPRO_CHANNEL_MASK_5_L_C_R_Bl_Br 0x0037 |
| |
| /* Speaker layout mask for five channels (5 mode, Home Theater). |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker front center |
| * - Speaker side left |
| * - Speaker side right |
| */ |
| #define WMAPRO_CHANNEL_MASK_5_L_C_R_Sl_Sr_HT 0x0607 |
| /* Speaker layout mask for six channels (5.1 mode). |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker front center |
| * - Speaker low frequency |
| * - Speaker back left |
| * - Speaker back right |
| */ |
| #define WMAPRO_CHANNEL_MASK_5DOT1_L_C_R_Bl_Br_SLF 0x003F |
| /* Speaker layout mask for six channels (5.1 mode, Home Theater). |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker front center |
| * - Speaker low frequency |
| * - Speaker side left |
| * - Speaker side right |
| */ |
| #define WMAPRO_CHANNEL_MASK_5DOT1_L_C_R_Sl_Sr_SLF_HT 0x060F |
| /* Speaker layout mask for six channels (5.1 mode, no LFE). |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker front center |
| * - Speaker back left |
| * - Speaker back right |
| * - Speaker back center |
| */ |
| #define WMAPRO_CHANNEL_MASK_5DOT1_L_C_R_Bl_Br_Bc 0x0137 |
| /* Speaker layout mask for six channels (5.1 mode, Home Theater, |
| * no LFE). |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker front center |
| * - Speaker back center |
| * - Speaker side left |
| * - Speaker side right |
| */ |
| #define WMAPRO_CHANNEL_MASK_5DOT1_L_C_R_Sl_Sr_Bc_HT 0x0707 |
| |
| /* Speaker layout mask for seven channels (6.1 mode). |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker front center |
| * - Speaker low frequency |
| * - Speaker back left |
| * - Speaker back right |
| * - Speaker back center |
| */ |
| #define WMAPRO_CHANNEL_MASK_6DOT1_L_C_R_Bl_Br_Bc_SLF 0x013F |
| |
| /* Speaker layout mask for seven channels (6.1 mode, Home |
| * Theater). |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker front center |
| * - Speaker low frequency |
| * - Speaker back center |
| * - Speaker side left |
| * - Speaker side right |
| */ |
| #define WMAPRO_CHANNEL_MASK_6DOT1_L_C_R_Sl_Sr_Bc_SLF_HT 0x070F |
| |
| /* Speaker layout mask for seven channels (6.1 mode, no LFE). |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker front center |
| * - Speaker back left |
| * - Speaker back right |
| * - Speaker front left of center |
| * - Speaker front right of center |
| */ |
| #define WMAPRO_CHANNEL_MASK_6DOT1_L_C_R_Bl_Br_SFLOC_SFROC 0x00F7 |
| |
| /* Speaker layout mask for seven channels (6.1 mode, Home |
| * Theater, no LFE). |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker front center |
| * - Speaker side left |
| * - Speaker side right |
| * - Speaker front left of center |
| * - Speaker front right of center |
| */ |
| #define WMAPRO_CHANNEL_MASK_6DOT1_L_C_R_Sl_Sr_SFLOC_SFROC_HT 0x0637 |
| |
| /* Speaker layout mask for eight channels (7.1 mode). |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker front center |
| * - Speaker back left |
| * - Speaker back right |
| * - Speaker low frequency |
| * - Speaker front left of center |
| * - Speaker front right of center |
| */ |
| #define WMAPRO_CHANNEL_MASK_7DOT1_L_C_R_Bl_Br_SLF_SFLOC_SFROC \ |
| 0x00FF |
| |
| /* Speaker layout mask for eight channels (7.1 mode, Home Theater). |
| * - Speaker front left |
| * - Speaker front right |
| * - Speaker front center |
| * - Speaker side left |
| * - Speaker side right |
| * - Speaker low frequency |
| * - Speaker front left of center |
| * - Speaker front right of center |
| * |
| */ |
| #define WMAPRO_CHANNEL_MASK_7DOT1_L_C_R_Sl_Sr_SLF_SFLOC_SFROC_HT \ |
| 0x063F |
| |
| #define ASM_PARAM_ID_DEC_OUTPUT_CHAN_MAP 0x00010D82 |
| |
| /* Maximum number of decoder output channels. */ |
| #define MAX_CHAN_MAP_CHANNELS 16 |
| |
| /* Structure for decoder output channel mapping. */ |
| |
| /* Payload of the #ASM_PARAM_ID_DEC_OUTPUT_CHAN_MAP parameter in the |
| * #ASM_STREAM_CMD_SET_ENCDEC_PARAM command. |
| */ |
| struct asm_dec_out_chan_map_param { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| u32 num_channels; |
| /* Number of decoder output channels. |
| * Supported values: 0 to #MAX_CHAN_MAP_CHANNELS |
| * |
| * A value of 0 indicates native channel mapping, which is valid |
| * only for NT mode. This means the output of the decoder is to be |
| * preserved as is. |
| */ |
| u8 channel_mapping[MAX_CHAN_MAP_CHANNELS]; |
| } __packed; |
| |
| #define ASM_STREAM_CMD_OPEN_WRITE_COMPRESSED 0x00010D84 |
| |
| /* Bitmask for the IEC 61937 enable flag.*/ |
| #define ASM_BIT_MASK_IEC_61937_STREAM_FLAG (0x00000001UL) |
| |
| /* Shift value for the IEC 61937 enable flag.*/ |
| #define ASM_SHIFT_IEC_61937_STREAM_FLAG 0 |
| |
| /* Bitmask for the IEC 60958 enable flag.*/ |
| #define ASM_BIT_MASK_IEC_60958_STREAM_FLAG (0x00000002UL) |
| |
| /* Shift value for the IEC 60958 enable flag.*/ |
| #define ASM_SHIFT_IEC_60958_STREAM_FLAG 1 |
| |
| /* Payload format for open write compressed command */ |
| |
| /* Payload format for the #ASM_STREAM_CMD_OPEN_WRITE_COMPRESSED |
| * command, which opens a stream for a given session ID and stream ID |
| * to be rendered in the compressed format. |
| */ |
| |
| struct asm_stream_cmd_open_write_compressed { |
| struct apr_hdr hdr; |
| u32 flags; |
| /* Mode flags that configure the stream for a specific format. |
| * Supported values: |
| * - Bit 0 -- IEC 61937 compatibility |
| * - 0 -- Stream is not in IEC 61937 format |
| * - 1 -- Stream is in IEC 61937 format |
| * - Bit 1 -- IEC 60958 compatibility |
| * - 0 -- Stream is not in IEC 60958 format |
| * - 1 -- Stream is in IEC 60958 format |
| * - Bits 2 to 31 -- 0 (Reserved) |
| * |
| * For the same stream, bit 0 cannot be set to 0 and bit 1 cannot |
| * be set to 1. A compressed stream connot have IEC 60958 |
| * packetization applied without IEC 61937 packetization. |
| * @note1hang Currently, IEC 60958 packetized input streams are not |
| * supported. |
| */ |
| |
| |
| u32 fmt_id; |
| /* Specifies the media type of the HDMI stream to be opened. |
| * Supported values: |
| * - #ASM_MEDIA_FMT_AC3 |
| * - #ASM_MEDIA_FMT_EAC3 |
| * - #ASM_MEDIA_FMT_DTS |
| * - #ASM_MEDIA_FMT_ATRAC |
| * - #ASM_MEDIA_FMT_MAT |
| * |
| * @note1hang This field must be set to a valid media type even if |
| * IEC 61937 packetization is not performed by the aDSP. |
| */ |
| |
| } __packed; |
| |
| |
| /* Indicates the number of samples per channel to be removed from the |
| * beginning of the stream. |
| */ |
| #define ASM_DATA_CMD_REMOVE_INITIAL_SILENCE 0x00010D67 |
| |
| /* Indicates the number of samples per channel to be removed from |
| * the end of the stream. |
| */ |
| #define ASM_DATA_CMD_REMOVE_TRAILING_SILENCE 0x00010D68 |
| |
| struct asm_data_cmd_remove_silence { |
| struct apr_hdr hdr; |
| u32 num_samples_to_remove; |
| /* < Number of samples per channel to be removed. |
| * @values 0 to (2@sscr{32}-1) |
| */ |
| } __packed; |
| |
| #define ASM_STREAM_CMD_OPEN_READ_COMPRESSED 0x00010D95 |
| |
| struct asm_stream_cmd_open_read_compressed { |
| struct apr_hdr hdr; |
| u32 mode_flags; |
| /* Mode flags that indicate whether meta information per encoded |
| * frame is to be provided. |
| * Supported values for bit 4: |
| * - 0 -- Return data buffer contains all encoded frames only; it does |
| * not contain frame metadata. |
| * - 1 -- Return data buffer contains an array of metadata and encoded |
| * frames. |
| * - Use #ASM_BIT_MASK_META_INFO_FLAG to set the bitmask and |
| * #ASM_SHIFT_META_INFO_FLAG to set the shift value for this bit. |
| * All other bits are reserved; clients must set them to zero. |
| */ |
| |
| u32 frames_per_buf; |
| /* Indicates the number of frames that need to be returned per |
| * read buffer |
| * Supported values: should be greater than 0 |
| */ |
| |
| } __packed; |
| |
| /* adsp_asm_stream_commands.h*/ |
| |
| |
| /* adsp_asm_api.h (no changes)*/ |
| #define ASM_STREAM_POSTPROCOPO_ID_DEFAULT \ |
| 0x00010BE4 |
| #define ASM_STREAM_POSTPROCOPO_ID_PEAKMETER \ |
| 0x00010D83 |
| #define ASM_STREAM_POSTPROCOPO_ID_NONE \ |
| 0x00010C68 |
| #define ASM_STREAM_POSTPROCOPO_ID_MCH_PEAK_VOL \ |
| 0x00010D8B |
| #define ASM_STREAM_PREPROCOPO_ID_DEFAULT \ |
| ASM_STREAM_POSTPROCOPO_ID_DEFAULT |
| #define ASM_STREAM_PREPROCOPO_ID_NONE \ |
| ASM_STREAM_POSTPROCOPO_ID_NONE |
| #define ADM_CMD_COPP_OPENOPOLOGY_ID_NONE_AUDIO_COPP \ |
| 0x00010312 |
| #define ADM_CMD_COPP_OPENOPOLOGY_ID_SPEAKER_MONO_AUDIO_COPP \ |
| 0x00010313 |
| #define ADM_CMD_COPP_OPENOPOLOGY_ID_SPEAKER_STEREO_AUDIO_COPP \ |
| 0x00010314 |
| #define ADM_CMD_COPP_OPENOPOLOGY_ID_SPEAKER_STEREO_IIR_AUDIO_COPP\ |
| 0x00010704 |
| #define ADM_CMD_COPP_OPENOPOLOGY_ID_SPEAKER_MONO_AUDIO_COPP_MBDRCV2\ |
| 0x0001070D |
| #define ADM_CMD_COPP_OPENOPOLOGY_ID_SPEAKER_STEREO_AUDIO_COPP_MBDRCV2\ |
| 0x0001070E |
| #define ADM_CMD_COPP_OPENOPOLOGY_ID_SPEAKER_STEREO_IIR_AUDIO_COPP_MBDRCV2\ |
| 0x0001070F |
| #define ADM_CMD_COPP_OPENOPOLOGY_ID_SPEAKER_STEREO_AUDIO_COPP_MBDRC_V3 \ |
| 0x11000000 |
| #define ADM_CMD_COPP_OPENOPOLOGY_ID_SPEAKER_MCH_PEAK_VOL \ |
| 0x0001031B |
| #define ADM_CMD_COPP_OPENOPOLOGY_ID_MIC_MONO_AUDIO_COPP 0x00010315 |
| #define ADM_CMD_COPP_OPENOPOLOGY_ID_MIC_STEREO_AUDIO_COPP 0x00010316 |
| #define AUDPROC_COPPOPOLOGY_ID_MCHAN_IIR_AUDIO 0x00010715 |
| #define ADM_CMD_COPP_OPENOPOLOGY_ID_DEFAULT_AUDIO_COPP 0x00010BE3 |
| #define ADM_CMD_COPP_OPENOPOLOGY_ID_PEAKMETER_AUDIO_COPP 0x00010317 |
| #define AUDPROC_MODULE_ID_AIG 0x00010716 |
| #define AUDPROC_PARAM_ID_AIG_ENABLE 0x00010717 |
| #define AUDPROC_PARAM_ID_AIG_CONFIG 0x00010718 |
| |
| struct Audio_AigParam { |
| uint16_t mode; |
| /*< Mode word for enabling AIG/SIG mode . |
| * Byte offset: 0 |
| */ |
| int16_t staticGainL16Q12; |
| /*< Static input gain when aigMode is set to 1. |
| * Byte offset: 2 |
| */ |
| int16_t initialGainDBL16Q7; |
| /*<Initial value that the adaptive gain update starts from dB |
| * Q7 Byte offset: 4 |
| */ |
| int16_t idealRMSDBL16Q7; |
| /*<Average RMS level that AIG attempts to achieve Q8.7 |
| * Byte offset: 6 |
| */ |
| int32_t noiseGateL32; |
| /*Threshold below which signal is considered as noise and AIG |
| * Byte offset: 8 |
| */ |
| int32_t minGainL32Q15; |
| /*Minimum gain that can be provided by AIG Q16.15 |
| * Byte offset: 12 |
| */ |
| int32_t maxGainL32Q15; |
| /*Maximum gain that can be provided by AIG Q16.15 |
| * Byte offset: 16 |
| */ |
| uint32_t gainAtRtUL32Q31; |
| /*Attack/release time for AIG update Q1.31 |
| * Byte offset: 20 |
| */ |
| uint32_t longGainAtRtUL32Q31; |
| /*Long attack/release time while updating gain for |
| * noise/silence Q1.31 Byte offset: 24 |
| */ |
| |
| uint32_t rmsTavUL32Q32; |
| /* RMS smoothing time constant used for long-term RMS estimate |
| * Q0.32 Byte offset: 28 |
| */ |
| |
| uint32_t gainUpdateStartTimMsUL32Q0; |
| /* The waiting time before which AIG starts to apply adaptive |
| * gain update Q32.0 Byte offset: 32 |
| */ |
| |
| } __packed; |
| |
| |
| #define ADM_MODULE_ID_EANS 0x00010C4A |
| #define ADM_PARAM_ID_EANS_ENABLE 0x00010C4B |
| #define ADM_PARAM_ID_EANS_PARAMS 0x00010C4C |
| |
| struct adm_eans_enable { |
| |
| uint32_t enable_flag; |
| /*< Specifies whether EANS is disabled (0) or enabled |
| * (nonzero). |
| * This is supported only for sampling rates of 8, 12, 16, 24, 32, |
| * and 48 kHz. It is not supported for sampling rates of 11.025, |
| * 22.05, or 44.1 kHz. |
| */ |
| |
| } __packed; |
| |
| |
| struct adm_eans_params { |
| int16_t eans_mode; |
| /*< Mode word for enabling/disabling submodules. |
| * Byte offset: 0 |
| */ |
| |
| int16_t eans_input_gain; |
| /*< Q2.13 input gain to the EANS module. |
| * Byte offset: 2 |
| */ |
| |
| int16_t eans_output_gain; |
| /*< Q2.13 output gain to the EANS module. |
| * Byte offset: 4 |
| */ |
| |
| int16_t eansarget_ns; |
| /*< Target noise suppression level in dB. |
| * Byte offset: 6 |
| */ |
| |
| int16_t eans_s_alpha; |
| /*< Q3.12 over-subtraction factor for stationary noise |
| * suppression. |
| * Byte offset: 8 |
| */ |
| |
| int16_t eans_n_alpha; |
| /* < Q3.12 over-subtraction factor for nonstationary noise |
| * suppression. |
| * Byte offset: 10 |
| */ |
| |
| int16_t eans_n_alphamax; |
| /*< Q3.12 maximum over-subtraction factor for nonstationary |
| * noise suppression. |
| * Byte offset: 12 |
| */ |
| int16_t eans_e_alpha; |
| /*< Q15 scaling factor for excess noise suppression. |
| * Byte offset: 14 |
| */ |
| |
| int16_t eans_ns_snrmax; |
| /*< Upper boundary in dB for SNR estimation. |
| * Byte offset: 16 |
| */ |
| |
| int16_t eans_sns_block; |
| /*< Quarter block size for stationary noise suppression. |
| * Byte offset: 18 |
| */ |
| |
| int16_t eans_ns_i; |
| /*< Initialization block size for noise suppression. |
| * Byte offset: 20 |
| */ |
| int16_t eans_np_scale; |
| /*< Power scale factor for nonstationary noise update. |
| * Byte offset: 22 |
| */ |
| |
| int16_t eans_n_lambda; |
| /*< Smoothing factor for higher level nonstationary noise |
| * update. |
| * Byte offset: 24 |
| */ |
| |
| int16_t eans_n_lambdaf; |
| /*< Medium averaging factor for noise update. |
| * Byte offset: 26 |
| */ |
| |
| int16_t eans_gs_bias; |
| /*< Bias factor in dB for gain calculation. |
| * Byte offset: 28 |
| */ |
| |
| int16_t eans_gs_max; |
| /*< SNR lower boundary in dB for aggressive gain calculation. |
| * Byte offset: 30 |
| */ |
| |
| int16_t eans_s_alpha_hb; |
| /*< Q3.12 over-subtraction factor for high-band stationary |
| * noise suppression. |
| * Byte offset: 32 |
| */ |
| |
| int16_t eans_n_alphamax_hb; |
| /*< Q3.12 maximum over-subtraction factor for high-band |
| * nonstationary noise suppression. |
| * Byte offset: 34 |
| */ |
| |
| int16_t eans_e_alpha_hb; |
| /*< Q15 scaling factor for high-band excess noise suppression. |
| * Byte offset: 36 |
| */ |
| |
| int16_t eans_n_lambda0; |
| /*< Smoothing factor for nonstationary noise update during |
| * speech activity. |
| * Byte offset: 38 |
| */ |
| |
| int16_t thresh; |
| /*< Threshold for generating a binary VAD decision. |
| * Byte offset: 40 |
| */ |
| |
| int16_t pwr_scale; |
| /*< Indirect lower boundary of the noise level estimate. |
| * Byte offset: 42 |
| */ |
| |
| int16_t hangover_max; |
| /*< Avoids mid-speech clipping and reliably detects weak speech |
| * bursts at the end of speech activity. |
| * Byte offset: 44 |
| */ |
| |
| int16_t alpha_snr; |
| /*< Controls responsiveness of the VAD. |
| * Byte offset: 46 |
| */ |
| |
| int16_t snr_diff_max; |
| /*< Maximum SNR difference. Decreasing this parameter value may |
| * help in making correct decisions during abrupt changes; however, |
| * decreasing too much may increase false alarms during long |
| * pauses/silences. |
| * Byte offset: 48 |
| */ |
| |
| int16_t snr_diff_min; |
| /*< Minimum SNR difference. Decreasing this parameter value may |
| * help in making correct decisions during abrupt changes; however, |
| * decreasing too much may increase false alarms during long |
| * pauses/silences. |
| * Byte offset: 50 |
| */ |
| |
| int16_t init_length; |
| /*< Defines the number of frames for which a noise level |
| * estimate is set to a fixed value. |
| * Byte offset: 52 |
| */ |
| |
| int16_t max_val; |
| /*< Defines the upper limit of the noise level. |
| * Byte offset: 54 |
| */ |
| |
| int16_t init_bound; |
| /*< Defines the initial bounding value for the noise level |
| * estimate. This is used during the initial segment defined by the |
| * init_length parameter. |
| * Byte offset: 56 |
| */ |
| |
| int16_t reset_bound; |
| /*< Reset boundary for noise tracking. |
| * Byte offset: 58 |
| */ |
| |
| int16_t avar_scale; |
| /*< Defines the bias factor in noise estimation. |
| * Byte offset: 60 |
| */ |
| |
| int16_t sub_nc; |
| /*< Defines the window length for noise estimation. |
| * Byte offset: 62 |
| */ |
| |
| int16_t spow_min; |
| /*< Defines the minimum signal power required to update the |
| * boundaries for the noise floor estimate. |
| * Byte offset: 64 |
| */ |
| |
| int16_t eans_gs_fast; |
| /*< Fast smoothing factor for postprocessor gain. |
| * Byte offset: 66 |
| */ |
| |
| int16_t eans_gs_med; |
| /*< Medium smoothing factor for postprocessor gain. |
| * Byte offset: 68 |
| */ |
| |
| int16_t eans_gs_slow; |
| /*< Slow smoothing factor for postprocessor gain. |
| * Byte offset: 70 |
| */ |
| |
| int16_t eans_swb_salpha; |
| /*< Q3.12 super wideband aggressiveness factor for stationary |
| * noise suppression. |
| * Byte offset: 72 |
| */ |
| |
| int16_t eans_swb_nalpha; |
| /*< Q3.12 super wideband aggressiveness factor for |
| * nonstationary noise suppression. |
| * Byte offset: 74 |
| */ |
| } __packed; |
| #define ADM_MODULE_IDX_MIC_GAIN_CTRL 0x00010C35 |
| |
| /* @addtogroup audio_pp_param_ids |
| * ID of the Tx mic gain control parameter used by the |
| * #ADM_MODULE_IDX_MIC_GAIN_CTRL module. |
| * @messagepayload |
| * @structure{admx_mic_gain} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ADM_PARAM_IDX_MIC_GAIN.tex} |
| */ |
| #define ADM_PARAM_IDX_MIC_GAIN 0x00010C36 |
| |
| /* Structure for a Tx mic gain parameter for the mic gain |
| * control module. |
| */ |
| |
| |
| /* @brief Payload of the #ADM_PARAM_IDX_MIC_GAIN parameter in the |
| * Tx Mic Gain Control module. |
| */ |
| struct admx_mic_gain { |
| uint16_t tx_mic_gain; |
| /*< Linear gain in Q13 format. */ |
| |
| uint16_t reserved; |
| /*< Clients must set this field to zero. */ |
| } __packed; |
| |
| struct adm_set_mic_gain_params { |
| struct adm_cmd_set_pp_params_v5 params; |
| struct adm_param_data_v5 data; |
| struct admx_mic_gain mic_gain_data; |
| } __packed; |
| |
| /* end_addtogroup audio_pp_param_ids */ |
| |
| /* @ingroup audio_pp_module_ids |
| * ID of the Rx Codec Gain Control module. |
| * |
| * This module supports the following parameter ID: |
| * - #ADM_PARAM_ID_RX_CODEC_GAIN |
| */ |
| #define ADM_MODULE_ID_RX_CODEC_GAIN_CTRL 0x00010C37 |
| |
| /* @addtogroup audio_pp_param_ids |
| * ID of the Rx codec gain control parameter used by the |
| * #ADM_MODULE_ID_RX_CODEC_GAIN_CTRL module. |
| * |
| * @messagepayload |
| * @structure{adm_rx_codec_gain} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ADM_PARAM_ID_RX_CODEC_GAIN.tex} |
| */ |
| #define ADM_PARAM_ID_RX_CODEC_GAIN 0x00010C38 |
| |
| /* Structure for the Rx common codec gain control module. */ |
| |
| |
| /* @brief Payload of the #ADM_PARAM_ID_RX_CODEC_GAIN parameter |
| * in the Rx Codec Gain Control module. |
| */ |
| |
| |
| struct adm_rx_codec_gain { |
| uint16_t rx_codec_gain; |
| /* Linear gain in Q13 format. */ |
| |
| uint16_t reserved; |
| /* Clients must set this field to zero.*/ |
| } __packed; |
| |
| /* end_addtogroup audio_pp_param_ids */ |
| |
| /* @ingroup audio_pp_module_ids |
| * ID of the HPF Tuning Filter module on the Tx path. |
| * This module supports the following parameter IDs: |
| * - #ADM_PARAM_ID_HPF_IIRX_FILTER_ENABLE_CONFIG |
| * - #ADM_PARAM_ID_HPF_IIRX_FILTER_PRE_GAIN |
| * - #ADM_PARAM_ID_HPF_IIRX_FILTER_CONFIG_PARAMS |
| */ |
| #define ADM_MODULE_ID_HPF_IIRX_FILTER 0x00010C3D |
| |
| /* @addtogroup audio_pp_param_ids */ |
| /* ID of the Tx HPF IIR filter enable parameter used by the |
| * #ADM_MODULE_ID_HPF_IIRX_FILTER module. |
| * @parspace Message payload |
| * @structure{adm_hpfx_iir_filter_enable_cfg} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ADM_PARAM_ID_HPF_IIRX_FILTER_ENABLE_CONFIG.tex} |
| */ |
| #define ADM_PARAM_ID_HPF_IIRX_FILTER_ENABLE_CONFIG 0x00010C3E |
| |
| /* ID of the Tx HPF IIR filter pregain parameter used by the |
| * #ADM_MODULE_ID_HPF_IIRX_FILTER module. |
| * @parspace Message payload |
| * @structure{adm_hpfx_iir_filter_pre_gain} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ADM_PARAM_ID_HPF_IIRX_FILTER_PRE_GAIN.tex} |
| */ |
| #define ADM_PARAM_ID_HPF_IIRX_FILTER_PRE_GAIN 0x00010C3F |
| |
| /* ID of the Tx HPF IIR filter configuration parameters used by the |
| * #ADM_MODULE_ID_HPF_IIRX_FILTER module. |
| * @parspace Message payload |
| * @structure{adm_hpfx_iir_filter_cfg_params} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ADM_PARAM_ID_HPF_IIRX_FILTER_CONFIG_PA |
| * RAMS.tex} |
| */ |
| #define ADM_PARAM_ID_HPF_IIRX_FILTER_CONFIG_PARAMS 0x00010C40 |
| |
| /* Structure for enabling a configuration parameter for |
| * the HPF IIR tuning filter module on the Tx path. |
| */ |
| |
| /* @brief Payload of the #ADM_PARAM_ID_HPF_IIRX_FILTER_ENABLE_CONFIG |
| * parameter in the Tx path HPF Tuning Filter module. |
| */ |
| struct adm_hpfx_iir_filter_enable_cfg { |
| uint32_t enable_flag; |
| /* Specifies whether the HPF tuning filter is disabled (0) or |
| * enabled (nonzero). |
| */ |
| } __packed; |
| |
| |
| /* Structure for the pregain parameter for the HPF |
| * IIR tuning filter module on the Tx path. |
| */ |
| |
| |
| /* @brief Payload of the #ADM_PARAM_ID_HPF_IIRX_FILTER_PRE_GAIN parameter |
| * in the Tx path HPF Tuning Filter module. |
| */ |
| struct adm_hpfx_iir_filter_pre_gain { |
| uint16_t pre_gain; |
| /* Linear gain in Q13 format. */ |
| |
| uint16_t reserved; |
| /* Clients must set this field to zero.*/ |
| } __packed; |
| |
| |
| /* Structure for the configuration parameter for the |
| * HPF IIR tuning filter module on the Tx path. |
| */ |
| |
| |
| /* @brief Payload of the #ADM_PARAM_ID_HPF_IIRX_FILTER_CONFIG_PARAMS |
| * parameters in the Tx path HPF Tuning Filter module. \n |
| * \n |
| * This structure is followed by tuning filter coefficients as follows: \n |
| * - Sequence of int32_t FilterCoeffs. |
| * Each band has five coefficients, each in int32_t format in the order of |
| * b0, b1, b2, a1, a2. |
| * - Sequence of int16_t NumShiftFactor. |
| * One int16_t per band. The numerator shift factor is related to the Q |
| * factor of the filter coefficients. |
| * - Sequence of uint16_t PanSetting. |
| * One uint16_t for each band to indicate application of the filter to |
| * left (0), right (1), or both (2) channels. |
| */ |
| struct adm_hpfx_iir_filter_cfg_params { |
| uint16_t num_biquad_stages; |
| /*< Number of bands. |
| * Supported values: 0 to 20 |
| */ |
| |
| uint16_t reserved; |
| /*< Clients must set this field to zero.*/ |
| } __packed; |
| |
| /* end_addtogroup audio_pp_module_ids */ |
| |
| /* @addtogroup audio_pp_module_ids */ |
| /* ID of the Tx path IIR Tuning Filter module. |
| * This module supports the following parameter IDs: |
| * - #ADM_PARAM_IDX_IIR_FILTER_ENABLE_CONFIG |
| */ |
| #define ADM_MODULE_IDX_IIR_FILTER 0x00010C41 |
| |
| /* ID of the Rx path IIR Tuning Filter module for the left channel. |
| * The parameter IDs of the IIR tuning filter module |
| * (#ASM_MODULE_ID_IIRUNING_FILTER) are used for the left IIR Rx tuning |
| * filter. |
| * |
| * Pan parameters are not required for this per-channel IIR filter; the pan |
| * parameters are ignored by this module. |
| */ |
| #define ADM_MODULE_ID_LEFT_IIRUNING_FILTER 0x00010705 |
| |
| /* ID of the the Rx path IIR Tuning Filter module for the right |
| * channel. |
| * The parameter IDs of the IIR tuning filter module |
| * (#ASM_MODULE_ID_IIRUNING_FILTER) are used for the right IIR Rx |
| * tuning filter. |
| * |
| * Pan parameters are not required for this per-channel IIR filter; |
| * the pan parameters are ignored by this module. |
| */ |
| #define ADM_MODULE_ID_RIGHT_IIRUNING_FILTER 0x00010706 |
| |
| /* end_addtogroup audio_pp_module_ids */ |
| |
| /* @addtogroup audio_pp_param_ids */ |
| |
| /* ID of the Tx IIR filter enable parameter used by the |
| * #ADM_MODULE_IDX_IIR_FILTER module. |
| * @parspace Message payload |
| * @structure{admx_iir_filter_enable_cfg} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ADM_PARAM_IDX_IIR_FILTER_ENABLE_CONFIG.tex} |
| */ |
| #define ADM_PARAM_IDX_IIR_FILTER_ENABLE_CONFIG 0x00010C42 |
| |
| /* ID of the Tx IIR filter pregain parameter used by the |
| * #ADM_MODULE_IDX_IIR_FILTER module. |
| * @parspace Message payload |
| * @structure{admx_iir_filter_pre_gain} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ADM_PARAM_IDX_IIR_FILTER_PRE_GAIN.tex} |
| */ |
| #define ADM_PARAM_IDX_IIR_FILTER_PRE_GAIN 0x00010C43 |
| |
| /* ID of the Tx IIR filter configuration parameters used by the |
| * #ADM_MODULE_IDX_IIR_FILTER module. |
| * @parspace Message payload |
| * @structure{admx_iir_filter_cfg_params} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ADM_PARAM_IDX_IIR_FILTER_CONFIG_PARAMS.tex} |
| */ |
| #define ADM_PARAM_IDX_IIR_FILTER_CONFIG_PARAMS 0x00010C44 |
| |
| /* Structure for enabling the configuration parameter for the |
| * IIR filter module on the Tx path. |
| */ |
| |
| /* @brief Payload of the #ADM_PARAM_IDX_IIR_FILTER_ENABLE_CONFIG |
| * parameter in the Tx Path IIR Tuning Filter module. |
| */ |
| |
| struct admx_iir_filter_enable_cfg { |
| uint32_t enable_flag; |
| /*< Specifies whether the IIR tuning filter is disabled (0) or |
| * enabled (nonzero). |
| */ |
| |
| } __packed; |
| |
| |
| /* Structure for the pregain parameter for the |
| * IIR filter module on the Tx path. |
| */ |
| |
| |
| /* @brief Payload of the #ADM_PARAM_IDX_IIR_FILTER_PRE_GAIN |
| * parameter in the Tx Path IIR Tuning Filter module. |
| */ |
| |
| struct admx_iir_filter_pre_gain { |
| uint16_t pre_gain; |
| /*< Linear gain in Q13 format. */ |
| |
| uint16_t reserved; |
| /*< Clients must set this field to zero.*/ |
| } __packed; |
| |
| |
| /* Structure for the configuration parameter for the |
| * IIR filter module on the Tx path. |
| */ |
| |
| |
| /* @brief Payload of the #ADM_PARAM_IDX_IIR_FILTER_CONFIG_PARAMS |
| * parameter in the Tx Path IIR Tuning Filter module. \n |
| * \n |
| * This structure is followed by the HPF IIR filter coefficients on |
| * the Tx path as follows: \n |
| * - Sequence of int32_t ulFilterCoeffs. Each band has five |
| * coefficients, each in int32_t format in the order of b0, b1, b2, |
| * a1, a2. |
| * - Sequence of int16_t sNumShiftFactor. One int16_t per band. The |
| * numerator shift factor is related to the Q factor of the filter |
| * coefficients. |
| * - Sequence of uint16_t usPanSetting. One uint16_t for each band |
| * to indicate if the filter is applied to left (0), right (1), or |
| * both (2) channels. |
| */ |
| struct admx_iir_filter_cfg_params { |
| uint16_t num_biquad_stages; |
| /*< Number of bands. |
| * Supported values: 0 to 20 |
| */ |
| |
| uint16_t reserved; |
| /*< Clients must set this field to zero.*/ |
| } __packed; |
| |
| /* end_addtogroup audio_pp_module_ids */ |
| |
| /* @ingroup audio_pp_module_ids |
| * ID of the QEnsemble module. |
| * This module supports the following parameter IDs: |
| * - #ADM_PARAM_ID_QENSEMBLE_ENABLE |
| * - #ADM_PARAM_ID_QENSEMBLE_BACKGAIN |
| * - #ADM_PARAM_ID_QENSEMBLE_SET_NEW_ANGLE |
| */ |
| #define ADM_MODULE_ID_QENSEMBLE 0x00010C59 |
| |
| /* @addtogroup audio_pp_param_ids */ |
| /* ID of the QEnsemble enable parameter used by the |
| * #ADM_MODULE_ID_QENSEMBLE module. |
| * @messagepayload |
| * @structure{adm_qensemble_enable} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ADM_PARAM_ID_QENSEMBLE_ENABLE.tex} |
| */ |
| #define ADM_PARAM_ID_QENSEMBLE_ENABLE 0x00010C60 |
| |
| /* ID of the QEnsemble back gain parameter used by the |
| * #ADM_MODULE_ID_QENSEMBLE module. |
| * @messagepayload |
| * @structure{adm_qensemble_param_backgain} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ADM_PARAM_ID_QENSEMBLE_BACKGAIN.tex} |
| */ |
| #define ADM_PARAM_ID_QENSEMBLE_BACKGAIN 0x00010C61 |
| |
| /* ID of the QEnsemble new angle parameter used by the |
| * #ADM_MODULE_ID_QENSEMBLE module. |
| * @messagepayload |
| * @structure{adm_qensemble_param_set_new_angle} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ADM_PARAM_ID_QENSEMBLE_SET_NEW_ANGLE.tex} |
| */ |
| #define ADM_PARAM_ID_QENSEMBLE_SET_NEW_ANGLE 0x00010C62 |
| |
| /* Structure for enabling the configuration parameter for the |
| * QEnsemble module. |
| */ |
| |
| |
| /* @brief Payload of the #ADM_PARAM_ID_QENSEMBLE_ENABLE |
| * parameter used by the QEnsemble module. |
| */ |
| struct adm_qensemble_enable { |
| uint32_t enable_flag; |
| /*< Specifies whether the QEnsemble module is disabled (0) or enabled |
| * (nonzero). |
| */ |
| } __packed; |
| |
| |
| /* Structure for the background gain for the QEnsemble module. */ |
| |
| |
| /* @brief Payload of the #ADM_PARAM_ID_QENSEMBLE_BACKGAIN |
| * parameter used by |
| * the QEnsemble module. |
| */ |
| struct adm_qensemble_param_backgain { |
| int16_t back_gain; |
| /*< Linear gain in Q15 format. |
| * Supported values: 0 to 32767 |
| */ |
| |
| uint16_t reserved; |
| /*< Clients must set this field to zero.*/ |
| } __packed; |
| /* Structure for setting a new angle for the QEnsemble module. */ |
| |
| |
| /* @brief Payload of the #ADM_PARAM_ID_QENSEMBLE_SET_NEW_ANGLE |
| * parameter used |
| * by the QEnsemble module. |
| */ |
| struct adm_qensemble_param_set_new_angle { |
| int16_t new_angle; |
| /*< New angle in degrees. |
| * Supported values: 0 to 359 |
| */ |
| |
| int16_t time_ms; |
| /*< Transition time in milliseconds to set the new angle. |
| * Supported values: 0 to 32767 |
| */ |
| } __packed; |
| |
| |
| #define ADM_CMD_GET_PP_TOPO_MODULE_LIST 0x00010349 |
| #define ADM_CMDRSP_GET_PP_TOPO_MODULE_LIST 0x00010350 |
| #define AUDPROC_PARAM_ID_ENABLE 0x00010904 |
| /* |
| * Payload of the ADM_CMD_GET_PP_TOPO_MODULE_LIST command. |
| */ |
| struct adm_cmd_get_pp_topo_module_list_t { |
| struct apr_hdr hdr; |
| /* Lower 32 bits of the 64-bit parameter data payload address. */ |
| uint32_t data_payload_addr_lsw; |
| /* |
| * Upper 32 bits of the 64-bit parameter data payload address. |
| * |
| * |
| * The size of the shared memory, if specified, must be large enough to |
| * contain the entire parameter data payload, including the module ID, |
| * parameter ID, parameter size, and parameter values. |
| */ |
| uint32_t data_payload_addr_msw; |
| /* |
| * Unique identifier for an address. |
| * |
| * This memory map handle is returned by the aDSP through the |
| * #ADM_CMD_SHARED_MEM_MAP_REGIONS command. |
| * |
| * @values |
| * - Non-NULL -- On acknowledgment, the parameter data payloads begin at |
| * the address specified (out-of-band) |
| * - NULL -- The acknowledgment's payload contains the parameter data |
| * (in-band) @tablebulletend |
| */ |
| uint32_t mem_map_handle; |
| /* |
| * Maximum data size of the list of modules. This |
| * field is a multiple of 4 bytes. |
| */ |
| uint16_t param_max_size; |
| /* This field must be set to zero. */ |
| uint16_t reserved; |
| } __packed; |
| |
| /* |
| * Payload of the ADM_CMDRSP_GET_PP_TOPO_MODULE_LIST message, which returns |
| * module ids in response to an ADM_CMD_GET_PP_TOPO_MODULE_LIST command. |
| * Immediately following this structure is the acknowledgment <b>module id |
| * data variable payload</b> containing the pre/postprocessing module id |
| * values. For an in-band scenario, the variable payload depends on the size |
| * of the parameter. |
| */ |
| struct adm_cmd_rsp_get_pp_topo_module_list_t { |
| /* Status message (error code). */ |
| uint32_t status; |
| } __packed; |
| |
| struct audproc_topology_module_id_info_t { |
| uint32_t num_modules; |
| } __packed; |
| |
| /* end_addtogroup audio_pp_module_ids */ |
| |
| /* @ingroup audio_pp_module_ids |
| * ID of the Volume Control module pre/postprocessing block. |
| * This module supports the following parameter IDs: |
| * - #ASM_PARAM_ID_VOL_CTRL_MASTER_GAIN |
| * - #ASM_PARAM_ID_MULTICHANNEL_GAIN |
| * - #ASM_PARAM_ID_VOL_CTRL_MUTE_CONFIG |
| * - #ASM_PARAM_ID_SOFT_VOL_STEPPING_PARAMETERS |
| * - #ASM_PARAM_ID_SOFT_PAUSE_PARAMETERS |
| * - #ASM_PARAM_ID_MULTICHANNEL_GAIN |
| * - #ASM_PARAM_ID_MULTICHANNEL_MUTE |
| */ |
| #define ASM_MODULE_ID_VOL_CTRL 0x00010BFE |
| #define ASM_MODULE_ID_VOL_CTRL2 0x00010910 |
| #define AUDPROC_MODULE_ID_VOL_CTRL ASM_MODULE_ID_VOL_CTRL |
| |
| /* @addtogroup audio_pp_param_ids */ |
| /* ID of the master gain parameter used by the #ASM_MODULE_ID_VOL_CTRL |
| * module. |
| * @messagepayload |
| * @structure{asm_volume_ctrl_master_gain} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ASM_PARAM_ID_VOL_CTRL_MASTER_GAIN.tex} |
| */ |
| #define ASM_PARAM_ID_VOL_CTRL_MASTER_GAIN 0x00010BFF |
| #define AUDPROC_PARAM_ID_VOL_CTRL_MASTER_GAIN ASM_PARAM_ID_VOL_CTRL_MASTER_GAIN |
| |
| /* ID of the left/right channel gain parameter used by the |
| * #ASM_MODULE_ID_VOL_CTRL module. |
| * @messagepayload |
| * @structure{asm_volume_ctrl_lr_chan_gain} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ASM_PARAM_ID_MULTICHANNEL_GAIN.tex} |
| */ |
| #define ASM_PARAM_ID_VOL_CTRL_LR_CHANNEL_GAIN 0x00010C00 |
| |
| /* ID of the mute configuration parameter used by the |
| * #ASM_MODULE_ID_VOL_CTRL module. |
| * @messagepayload |
| * @structure{asm_volume_ctrl_mute_config} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ASM_PARAM_ID_VOL_CTRL_MUTE_CONFIG.tex} |
| */ |
| #define ASM_PARAM_ID_VOL_CTRL_MUTE_CONFIG 0x00010C01 |
| |
| /* ID of the soft stepping volume parameters used by the |
| * #ASM_MODULE_ID_VOL_CTRL module. |
| * @messagepayload |
| * @structure{asm_soft_step_volume_params} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ASM_PARAM_ID_SOFT_VOL_STEPPING_PARAMET |
| * ERS.tex} |
| */ |
| #define ASM_PARAM_ID_SOFT_VOL_STEPPING_PARAMETERS 0x00010C29 |
| #define AUDPROC_PARAM_ID_SOFT_VOL_STEPPING_PARAMETERS\ |
| ASM_PARAM_ID_SOFT_VOL_STEPPING_PARAMETERS |
| |
| /* ID of the soft pause parameters used by the #ASM_MODULE_ID_VOL_CTRL |
| * module. |
| */ |
| #define ASM_PARAM_ID_SOFT_PAUSE_PARAMETERS 0x00010D6A |
| |
| /* ID of the multiple-channel volume control parameters used by the |
| * #ASM_MODULE_ID_VOL_CTRL module. |
| */ |
| #define ASM_PARAM_ID_MULTICHANNEL_GAIN 0x00010713 |
| |
| /* ID of the multiple-channel mute configuration parameters used by the |
| * #ASM_MODULE_ID_VOL_CTRL module. |
| */ |
| |
| #define ASM_PARAM_ID_MULTICHANNEL_MUTE 0x00010714 |
| |
| /* Structure for the master gain parameter for a volume control |
| * module. |
| */ |
| |
| |
| /* @brief Payload of the #ASM_PARAM_ID_VOL_CTRL_MASTER_GAIN |
| * parameter used by the Volume Control module. |
| */ |
| |
| |
| |
| struct asm_volume_ctrl_master_gain { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_pp_params_v2 param; |
| struct asm_stream_param_data_v2 data; |
| uint16_t master_gain; |
| /* Linear gain in Q13 format. */ |
| |
| uint16_t reserved; |
| /* Clients must set this field to zero. */ |
| } __packed; |
| |
| |
| struct asm_volume_ctrl_lr_chan_gain { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_pp_params_v2 param; |
| struct asm_stream_param_data_v2 data; |
| |
| uint16_t l_chan_gain; |
| /*< Linear gain in Q13 format for the left channel. */ |
| |
| uint16_t r_chan_gain; |
| /*< Linear gain in Q13 format for the right channel.*/ |
| } __packed; |
| |
| |
| /* Structure for the mute configuration parameter for a |
| * volume control module. |
| */ |
| |
| |
| /* @brief Payload of the #ASM_PARAM_ID_VOL_CTRL_MUTE_CONFIG |
| * parameter used by the Volume Control module. |
| */ |
| |
| |
| struct asm_volume_ctrl_mute_config { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_pp_params_v2 param; |
| struct asm_stream_param_data_v2 data; |
| uint32_t mute_flag; |
| /*< Specifies whether mute is disabled (0) or enabled (nonzero).*/ |
| |
| } __packed; |
| |
| /* |
| * Supported parameters for a soft stepping linear ramping curve. |
| */ |
| #define ASM_PARAM_SVC_RAMPINGCURVE_LINEAR 0 |
| |
| /* |
| * Exponential ramping curve. |
| */ |
| #define ASM_PARAM_SVC_RAMPINGCURVE_EXP 1 |
| |
| /* |
| * Logarithmic ramping curve. |
| */ |
| #define ASM_PARAM_SVC_RAMPINGCURVE_LOG 2 |
| |
| /* Structure for holding soft stepping volume parameters. */ |
| |
| |
| /* Payload of the #ASM_PARAM_ID_SOFT_VOL_STEPPING_PARAMETERS |
| * parameters used by the Volume Control module. |
| */ |
| struct asm_soft_step_volume_params { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_pp_params_v2 param; |
| struct asm_stream_param_data_v2 data; |
| uint32_t period; |
| /*< Period in milliseconds. |
| * Supported values: 0 to 15000 |
| */ |
| |
| uint32_t step; |
| /*< Step in microseconds. |
| * Supported values: 0 to 15000000 |
| */ |
| |
| uint32_t ramping_curve; |
| /*< Ramping curve type. |
| * Supported values: |
| * - #ASM_PARAM_SVC_RAMPINGCURVE_LINEAR |
| * - #ASM_PARAM_SVC_RAMPINGCURVE_EXP |
| * - #ASM_PARAM_SVC_RAMPINGCURVE_LOG |
| */ |
| } __packed; |
| |
| |
| /* Structure for holding soft pause parameters. */ |
| |
| |
| /* Payload of the #ASM_PARAM_ID_SOFT_PAUSE_PARAMETERS |
| * parameters used by the Volume Control module. |
| */ |
| |
| |
| struct asm_soft_pause_params { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_pp_params_v2 param; |
| struct asm_stream_param_data_v2 data; |
| uint32_t enable_flag; |
| /*< Specifies whether soft pause is disabled (0) or enabled |
| * (nonzero). |
| */ |
| |
| |
| |
| uint32_t period; |
| /*< Period in milliseconds. |
| * Supported values: 0 to 15000 |
| */ |
| |
| uint32_t step; |
| /*< Step in microseconds. |
| * Supported values: 0 to 15000000 |
| */ |
| |
| uint32_t ramping_curve; |
| /*< Ramping curve. |
| * Supported values: |
| * - #ASM_PARAM_SVC_RAMPINGCURVE_LINEAR |
| * - #ASM_PARAM_SVC_RAMPINGCURVE_EXP |
| * - #ASM_PARAM_SVC_RAMPINGCURVE_LOG |
| */ |
| } __packed; |
| |
| |
| /* Maximum number of channels.*/ |
| #define VOLUME_CONTROL_MAX_CHANNELS 8 |
| |
| /* Structure for holding one channel type - gain pair. */ |
| |
| |
| /* Payload of the #ASM_PARAM_ID_MULTICHANNEL_GAIN channel |
| * type/gain pairs used by the Volume Control module. \n \n This |
| * structure immediately follows the |
| * asm_volume_ctrl_multichannel_gain structure. |
| */ |
| |
| |
| struct asm_volume_ctrl_channeltype_gain_pair { |
| uint8_t channeltype; |
| /* |
| * Channel type for which the gain setting is to be applied. |
| * Supported values: |
| * - #PCM_CHANNEL_L |
| * - #PCM_CHANNEL_R |
| * - #PCM_CHANNEL_C |
| * - #PCM_CHANNEL_LS |
| * - #PCM_CHANNEL_RS |
| * - #PCM_CHANNEL_LFE |
| * - #PCM_CHANNEL_CS |
| * - #PCM_CHANNEL_LB |
| * - #PCM_CHANNEL_RB |
| * - #PCM_CHANNELS |
| * - #PCM_CHANNEL_CVH |
| * - #PCM_CHANNEL_MS |
| * - #PCM_CHANNEL_FLC |
| * - #PCM_CHANNEL_FRC |
| * - #PCM_CHANNEL_RLC |
| * - #PCM_CHANNEL_RRC |
| */ |
| |
| uint8_t reserved1; |
| /* Clients must set this field to zero. */ |
| |
| uint8_t reserved2; |
| /* Clients must set this field to zero. */ |
| |
| uint8_t reserved3; |
| /* Clients must set this field to zero. */ |
| |
| uint32_t gain; |
| /* |
| * Gain value for this channel in Q28 format. |
| * Supported values: Any |
| */ |
| } __packed; |
| |
| |
| /* Structure for the multichannel gain command */ |
| |
| |
| /* Payload of the #ASM_PARAM_ID_MULTICHANNEL_GAIN |
| * parameters used by the Volume Control module. |
| */ |
| |
| |
| struct asm_volume_ctrl_multichannel_gain { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_pp_params_v2 param; |
| struct asm_stream_param_data_v2 data; |
| uint32_t num_channels; |
| /* |
| * Number of channels for which gain values are provided. Any |
| * channels present in the data for which gain is not provided are |
| * set to unity gain. |
| * Supported values: 1 to 8 |
| */ |
| |
| struct asm_volume_ctrl_channeltype_gain_pair |
| gain_data[VOLUME_CONTROL_MAX_CHANNELS]; |
| /* Array of channel type/gain pairs.*/ |
| } __packed; |
| |
| |
| /* Structure for holding one channel type - mute pair. */ |
| |
| |
| /* Payload of the #ASM_PARAM_ID_MULTICHANNEL_MUTE channel |
| * type/mute setting pairs used by the Volume Control module. \n \n |
| * This structure immediately follows the |
| * asm_volume_ctrl_multichannel_mute structure. |
| */ |
| |
| |
| struct asm_volume_ctrl_channelype_mute_pair { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_pp_params_v2 param; |
| struct asm_stream_param_data_v2 data; |
| uint8_t channelype; |
| /*< Channel type for which the mute setting is to be applied. |
| * Supported values: |
| * - #PCM_CHANNEL_L |
| * - #PCM_CHANNEL_R |
| * - #PCM_CHANNEL_C |
| * - #PCM_CHANNEL_LS |
| * - #PCM_CHANNEL_RS |
| * - #PCM_CHANNEL_LFE |
| * - #PCM_CHANNEL_CS |
| * - #PCM_CHANNEL_LB |
| * - #PCM_CHANNEL_RB |
| * - #PCM_CHANNELS |
| * - #PCM_CHANNEL_CVH |
| * - #PCM_CHANNEL_MS |
| * - #PCM_CHANNEL_FLC |
| * - #PCM_CHANNEL_FRC |
| * - #PCM_CHANNEL_RLC |
| * - #PCM_CHANNEL_RRC |
| */ |
| |
| uint8_t reserved1; |
| /*< Clients must set this field to zero. */ |
| |
| uint8_t reserved2; |
| /*< Clients must set this field to zero. */ |
| |
| uint8_t reserved3; |
| /*< Clients must set this field to zero. */ |
| |
| uint32_t mute; |
| /*< Mute setting for this channel. |
| * Supported values: |
| * - 0 = Unmute |
| * - Nonzero = Mute |
| */ |
| } __packed; |
| |
| |
| /* Structure for the multichannel mute command */ |
| |
| |
| /* @brief Payload of the #ASM_PARAM_ID_MULTICHANNEL_MUTE |
| * parameters used by the Volume Control module. |
| */ |
| |
| |
| struct asm_volume_ctrl_multichannel_mute { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_pp_params_v2 param; |
| struct asm_stream_param_data_v2 data; |
| uint32_t num_channels; |
| /*< Number of channels for which mute configuration is |
| * provided. Any channels present in the data for which mute |
| * configuration is not provided are set to unmute. |
| * Supported values: 1 to 8 |
| */ |
| |
| struct asm_volume_ctrl_channelype_mute_pair |
| mute_data[VOLUME_CONTROL_MAX_CHANNELS]; |
| /*< Array of channel type/mute setting pairs.*/ |
| } __packed; |
| /* end_addtogroup audio_pp_param_ids */ |
| |
| /* audio_pp_module_ids |
| * ID of the IIR Tuning Filter module. |
| * This module supports the following parameter IDs: |
| * - #ASM_PARAM_ID_IIRUNING_FILTER_ENABLE_CONFIG |
| * - #ASM_PARAM_ID_IIRUNING_FILTER_PRE_GAIN |
| * - #ASM_PARAM_ID_IIRUNING_FILTER_CONFIG_PARAMS |
| */ |
| #define ASM_MODULE_ID_IIRUNING_FILTER 0x00010C02 |
| |
| /* @addtogroup audio_pp_param_ids */ |
| /* ID of the IIR tuning filter enable parameter used by the |
| * #ASM_MODULE_ID_IIRUNING_FILTER module. |
| * @messagepayload |
| * @structure{asm_iiruning_filter_enable} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ASM_PARAM_ID_IIRUNING_FILTER_ENABLE_CO |
| * NFIG.tex} |
| */ |
| #define ASM_PARAM_ID_IIRUNING_FILTER_ENABLE_CONFIG 0x00010C03 |
| |
| /* ID of the IIR tuning filter pregain parameter used by the |
| * #ASM_MODULE_ID_IIRUNING_FILTER module. |
| */ |
| #define ASM_PARAM_ID_IIRUNING_FILTER_PRE_GAIN 0x00010C04 |
| |
| /* ID of the IIR tuning filter configuration parameters used by the |
| * #ASM_MODULE_ID_IIRUNING_FILTER module. |
| */ |
| #define ASM_PARAM_ID_IIRUNING_FILTER_CONFIG_PARAMS 0x00010C05 |
| |
| /* Structure for an enable configuration parameter for an |
| * IIR tuning filter module. |
| */ |
| |
| |
| /* @brief Payload of the #ASM_PARAM_ID_IIRUNING_FILTER_ENABLE_CONFIG |
| * parameter used by the IIR Tuning Filter module. |
| */ |
| struct asm_iiruning_filter_enable { |
| uint32_t enable_flag; |
| /*< Specifies whether the IIR tuning filter is disabled (0) or |
| * enabled (1). |
| */ |
| } __packed; |
| |
| /* Structure for the pregain parameter for an IIR tuning filter module. */ |
| |
| |
| /* Payload of the #ASM_PARAM_ID_IIRUNING_FILTER_PRE_GAIN |
| * parameters used by the IIR Tuning Filter module. |
| */ |
| struct asm_iiruning_filter_pregain { |
| uint16_t pregain; |
| /*< Linear gain in Q13 format. */ |
| |
| uint16_t reserved; |
| /*< Clients must set this field to zero.*/ |
| } __packed; |
| |
| /* Structure for the configuration parameter for an IIR tuning filter |
| * module. |
| */ |
| |
| |
| /* @brief Payload of the #ASM_PARAM_ID_IIRUNING_FILTER_CONFIG_PARAMS |
| * parameters used by the IIR Tuning Filter module. \n |
| * \n |
| * This structure is followed by the IIR filter coefficients: \n |
| * - Sequence of int32_t FilterCoeffs \n |
| * Five coefficients for each band. Each coefficient is in int32_t format, in |
| * the order of b0, b1, b2, a1, a2. |
| * - Sequence of int16_t NumShiftFactor \n |
| * One int16_t per band. The numerator shift factor is related to the Q |
| * factor of the filter coefficients. |
| * - Sequence of uint16_t PanSetting \n |
| * One uint16_t per band, indicating if the filter is applied to left (0), |
| * right (1), or both (2) channels. |
| */ |
| struct asm_iir_filter_config_params { |
| uint16_t num_biquad_stages; |
| /*< Number of bands. |
| * Supported values: 0 to 20 |
| */ |
| |
| uint16_t reserved; |
| /*< Clients must set this field to zero.*/ |
| } __packed; |
| |
| /* audio_pp_module_ids |
| * ID of the Multiband Dynamic Range Control (MBDRC) module on the Tx/Rx |
| * paths. |
| * This module supports the following parameter IDs: |
| * - #ASM_PARAM_ID_MBDRC_ENABLE |
| * - #ASM_PARAM_ID_MBDRC_CONFIG_PARAMS |
| */ |
| #define ASM_MODULE_ID_MBDRC 0x00010C06 |
| |
| /* audio_pp_param_ids */ |
| /* ID of the MBDRC enable parameter used by the #ASM_MODULE_ID_MBDRC module. |
| * @messagepayload |
| * @structure{asm_mbdrc_enable} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ASM_PARAM_ID_MBDRC_ENABLE.tex} |
| */ |
| #define ASM_PARAM_ID_MBDRC_ENABLE 0x00010C07 |
| |
| /* ID of the MBDRC configuration parameters used by the |
| * #ASM_MODULE_ID_MBDRC module. |
| * @messagepayload |
| * @structure{asm_mbdrc_config_params} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ASM_PARAM_ID_MBDRC_CONFIG_PARAMS.tex} |
| * |
| * @parspace Sub-band DRC configuration parameters |
| * @structure{asm_subband_drc_config_params} |
| * @tablespace |
| * @inputtable{Audio_Postproc_ASM_PARAM_ID_MBDRC_CONFIG_PARAMS_subband_DRC.tex} |
| * |
| * @keep{6} |
| * To obtain legacy ADRC from MBDRC, use the calibration tool to: |
| * |
| * - Enable MBDRC (EnableFlag = TRUE) |
| * - Set number of bands to 1 (uiNumBands = 1) |
| * - Enable the first MBDRC band (DrcMode[0] = DRC_ENABLED = 1) |
| * - Clear the first band mute flag (MuteFlag[0] = 0) |
| * - Set the first band makeup gain to unity (compMakeUpGain[0] = 0x2000) |
| * - Use the legacy ADRC parameters to calibrate the rest of the MBDRC |
| * parameters. |
| */ |
| #define ASM_PARAM_ID_MBDRC_CONFIG_PARAMS 0x00010C08 |
| |
| /* end_addtogroup audio_pp_param_ids */ |
| |
| /* audio_pp_module_ids |
| * ID of the MMBDRC module version 2 pre/postprocessing block. |
| * This module differs from the original MBDRC (#ASM_MODULE_ID_MBDRC) in |
| * the length of the filters used in each sub-band. |
| * This module supports the following parameter ID: |
| * - #ASM_PARAM_ID_MBDRC_CONFIG_PARAMS_IMPROVED_FILTBANK_V2 |
| */ |
| #define ASM_MODULE_ID_MBDRCV2 0x0001070B |
| |
| /* @addtogroup audio_pp_param_ids */ |
| /* ID of the configuration parameters used by the |
| * #ASM_MODULE_ID_MBDRCV2 module for the improved filter structure |
| * of the MBDRC v2 pre/postprocessing block. |
| * The update to this configuration structure from the original |
| * MBDRC is the number of filter coefficients in the filter |
| * structure. The sequence for is as follows: |
| * - 1 band = 0 FIR coefficient + 1 mute flag + uint16_t padding |
| * - 2 bands = 141 FIR coefficients + 2 mute flags + uint16_t padding |
| * - 3 bands = 141+81 FIR coefficients + 3 mute flags + uint16_t padding |
| * - 4 bands = 141+81+61 FIR coefficients + 4 mute flags + uint16_t |
| * padding |
| * - 5 bands = 141+81+61+61 FIR coefficients + 5 mute flags + |
| * uint16_t padding |
| * This block uses the same parameter structure as |
| * #ASM_PARAM_ID_MBDRC_CONFIG_PARAMS. |
| */ |
| #define ASM_PARAM_ID_MBDRC_CONFIG_PARAMS_IMPROVED_FILTBANK_V2 \ |
| 0x0001070C |
| |
| #define ASM_MODULE_ID_MBDRCV3 0x0001090B |
| /* |
| * ID of the MMBDRC module version 3 pre/postprocessing block. |
| * This module differs from MBDRCv2 (#ASM_MODULE_ID_MBDRCV2) in |
| * that it supports both 16- and 24-bit data. |
| * This module supports the following parameter ID: |
| * - #ASM_PARAM_ID_MBDRC_ENABLE |
| * - #ASM_PARAM_ID_MBDRC_CONFIG_PARAMS |
| * - #ASM_PARAM_ID_MBDRC_CONFIG_PARAMS_V3 |
| * - #ASM_PARAM_ID_MBDRC_FILTER_XOVER_FREQS |
| */ |
| |
| /* Structure for the enable parameter for an MBDRC module. */ |
| |
| |
| /* Payload of the #ASM_PARAM_ID_MBDRC_ENABLE parameter used by the |
| * MBDRC module. |
| */ |
| struct asm_mbdrc_enable { |
| uint32_t enable_flag; |
| /*< Specifies whether MBDRC is disabled (0) or enabled (nonzero).*/ |
| } __packed; |
| |
| /* Structure for the configuration parameters for an MBDRC module. */ |
| |
| |
| /* Payload of the #ASM_PARAM_ID_MBDRC_CONFIG_PARAMS |
| * parameters used by the MBDRC module. \n \n Following this |
| * structure is the payload for sub-band DRC configuration |
| * parameters (asm_subband_drc_config_params). This sub-band |
| * structure must be repeated for each band. |
| */ |
| |
| |
| struct asm_mbdrc_config_params { |
| uint16_t num_bands; |
| /*< Number of bands. |
| * Supported values: 1 to 5 |
| */ |
| |
| int16_t limiterhreshold; |
| /*< Threshold in decibels for the limiter output. |
| * Supported values: -72 to 18 \n |
| * Recommended value: 3994 (-0.22 db in Q3.12 format) |
| */ |
| |
| int16_t limiter_makeup_gain; |
| /*< Makeup gain in decibels for the limiter output. |
| * Supported values: -42 to 42 \n |
| * Recommended value: 256 (0 dB in Q7.8 format) |
| */ |
| |
| int16_t limiter_gc; |
| /*< Limiter gain recovery coefficient. |
| * Supported values: 0.5 to 0.99 \n |
| * Recommended value: 32440 (0.99 in Q15 format) |
| */ |
| |
| int16_t limiter_delay; |
| /*< Limiter delay in samples. |
| * Supported values: 0 to 10 \n |
| * Recommended value: 262 (0.008 samples in Q15 format) |
| */ |
| |
| int16_t limiter_max_wait; |
| /*< Maximum limiter waiting time in samples. |
| * Supported values: 0 to 10 \n |
| * Recommended value: 262 (0.008 samples in Q15 format) |
| */ |
| } __packed; |
| |
| /* DRC configuration structure for each sub-band of an MBDRC module. */ |
| |
| |
| /* Payload of the #ASM_PARAM_ID_MBDRC_CONFIG_PARAMS DRC |
| * configuration parameters for each sub-band in the MBDRC module. |
| * After this DRC structure is configured for valid bands, the next |
| * MBDRC setparams expects the sequence of sub-band MBDRC filter |
| * coefficients (the length depends on the number of bands) plus the |
| * mute flag for that band plus uint16_t padding. |
| * |
| * @keep{10} |
| * The filter coefficient and mute flag are of type int16_t: |
| * - FIR coefficient = int16_t firFilter |
| * - Mute flag = int16_t fMuteFlag |
| * |
| * The sequence is as follows: |
| * - 1 band = 0 FIR coefficient + 1 mute flag + uint16_t padding |
| * - 2 bands = 97 FIR coefficients + 2 mute flags + uint16_t padding |
| * - 3 bands = 97+33 FIR coefficients + 3 mute flags + uint16_t padding |
| * - 4 bands = 97+33+33 FIR coefficients + 4 mute flags + uint16_t padding |
| * - 5 bands = 97+33+33+33 FIR coefficients + 5 mute flags + uint16_t padding |
| * |
| * For improved filterbank, the sequence is as follows: |
| * - 1 band = 0 FIR coefficient + 1 mute flag + uint16_t padding |
| * - 2 bands = 141 FIR coefficients + 2 mute flags + uint16_t padding |
| * - 3 bands = 141+81 FIR coefficients + 3 mute flags + uint16_t padding |
| * - 4 bands = 141+81+61 FIR coefficients + 4 mute flags + uint16_t padding |
| * - 5 bands = 141+81+61+61 FIR coefficients + 5 mute flags + uint16_t padding |
| */ |
| struct asm_subband_drc_config_params { |
| int16_t drc_stereo_linked_flag; |
| /*< Specifies whether all stereo channels have the same applied |
| * dynamics (1) or if they process their dynamics independently (0). |
| * Supported values: |
| * - 0 -- Not linked |
| * - 1 -- Linked |
| */ |
| |
| int16_t drc_mode; |
| /*< Specifies whether DRC mode is bypassed for sub-bands. |
| * Supported values: |
| * - 0 -- Disabled |
| * - 1 -- Enabled |
| */ |
| |
| int16_t drc_down_sample_level; |
| /*< DRC down sample level. |
| * Supported values: @ge 1 |
| */ |
| |
| int16_t drc_delay; |
| /*< DRC delay in samples. |
| * Supported values: 0 to 1200 |
| */ |
| |
| uint16_t drc_rmsime_avg_const; |
| /*< RMS signal energy time-averaging constant. |
| * Supported values: 0 to 2^16-1 |
| */ |
| |
| uint16_t drc_makeup_gain; |
| /*< DRC makeup gain in decibels. |
| * Supported values: 258 to 64917 |
| */ |
| /* Down expander settings */ |
| int16_t down_expdrhreshold; |
| /*< Down expander threshold. |
| * Supported Q7 format values: 1320 to up_cmpsrhreshold |
| */ |
| |
| int16_t down_expdr_slope; |
| /*< Down expander slope. |
| * Supported Q8 format values: -32768 to 0. |
| */ |
| |
| uint32_t down_expdr_attack; |
| /*< Down expander attack constant. |
| * Supported Q31 format values: 196844 to 2^31. |
| */ |
| |
| uint32_t down_expdr_release; |
| /*< Down expander release constant. |
| * Supported Q31 format values: 19685 to 2^31 |
| */ |
| |
| uint16_t down_expdr_hysteresis; |
| /*< Down expander hysteresis constant. |
| * Supported Q14 format values: 1 to 32690 |
| */ |
| |
| uint16_t reserved; |
| /*< Clients must set this field to zero. */ |
| |
| int32_t down_expdr_min_gain_db; |
| /*< Down expander minimum gain. |
| * Supported Q23 format values: -805306368 to 0. |
| */ |
| |
| /* Up compressor settings */ |
| |
| int16_t up_cmpsrhreshold; |
| /*< Up compressor threshold. |
| * Supported Q7 format values: down_expdrhreshold to |
| * down_cmpsrhreshold. |
| */ |
| |
| uint16_t up_cmpsr_slope; |
| /*< Up compressor slope. |
| * Supported Q16 format values: 0 to 64881. |
| */ |
| |
| uint32_t up_cmpsr_attack; |
| /*< Up compressor attack constant. |
| * Supported Q31 format values: 196844 to 2^31. |
| */ |
| |
| uint32_t up_cmpsr_release; |
| /*< Up compressor release constant. |
| * Supported Q31 format values: 19685 to 2^31. |
| */ |
| |
| uint16_t up_cmpsr_hysteresis; |
| /*< Up compressor hysteresis constant. |
| * Supported Q14 format values: 1 to 32690. |
| */ |
| |
| /* Down compressor settings */ |
| |
| int16_t down_cmpsrhreshold; |
| /*< Down compressor threshold. |
| * Supported Q7 format values: up_cmpsrhreshold to 11560. |
| */ |
| |
| uint16_t down_cmpsr_slope; |
| /*< Down compressor slope. |
| * Supported Q16 format values: 0 to 64881. |
| */ |
| |
| uint16_t reserved1; |
| /*< Clients must set this field to zero. */ |
| |
| uint32_t down_cmpsr_attack; |
| /*< Down compressor attack constant. |
| * Supported Q31 format values: 196844 to 2^31. |
| */ |
| |
| uint32_t down_cmpsr_release; |
| /*< Down compressor release constant. |
| * Supported Q31 format values: 19685 to 2^31. |
| */ |
| |
| uint16_t down_cmpsr_hysteresis; |
| /*< Down compressor hysteresis constant. |
| * Supported Q14 values: 1 to 32690. |
| */ |
| |
| uint16_t reserved2; |
| /*< Clients must set this field to zero.*/ |
| } __packed; |
| |
| #define ASM_MODULE_ID_EQUALIZER 0x00010C27 |
| #define ASM_PARAM_ID_EQUALIZER_PARAMETERS 0x00010C28 |
| |
| #define ASM_MAX_EQ_BANDS 12 |
| |
| struct asm_eq_per_band_params { |
| uint32_t band_idx; |
| /*< Band index. |
| * Supported values: 0 to 11 |
| */ |
| |
| uint32_t filterype; |
| /*< Type of filter. |
| * Supported values: |
| * - #ASM_PARAM_EQYPE_NONE |
| * - #ASM_PARAM_EQ_BASS_BOOST |
| * - #ASM_PARAM_EQ_BASS_CUT |
| * - #ASM_PARAM_EQREBLE_BOOST |
| * - #ASM_PARAM_EQREBLE_CUT |
| * - #ASM_PARAM_EQ_BAND_BOOST |
| * - #ASM_PARAM_EQ_BAND_CUT |
| */ |
| |
| uint32_t center_freq_hz; |
| /*< Filter band center frequency in Hertz. */ |
| |
| int32_t filter_gain; |
| /*< Filter band initial gain. |
| * Supported values: +12 to -12 dB in 1 dB increments |
| */ |
| |
| int32_t q_factor; |
| /*< Filter band quality factor expressed as a Q8 number, i.e., a |
| * fixed-point number with q factor of 8. For example, 3000/(2^8). |
| */ |
| } __packed; |
| |
| struct asm_eq_params { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_pp_params_v2 param; |
| struct asm_stream_param_data_v2 data; |
| uint32_t enable_flag; |
| /*< Specifies whether the equalizer module is disabled (0) or enabled |
| * (nonzero). |
| */ |
| |
| uint32_t num_bands; |
| /*< Number of bands. |
| * Supported values: 1 to 12 |
| */ |
| struct asm_eq_per_band_params eq_bands[ASM_MAX_EQ_BANDS]; |
| |
| } __packed; |
| |
| /* No equalizer effect.*/ |
| #define ASM_PARAM_EQYPE_NONE 0 |
| |
| /* Bass boost equalizer effect.*/ |
| #define ASM_PARAM_EQ_BASS_BOOST 1 |
| |
| /*Bass cut equalizer effect.*/ |
| #define ASM_PARAM_EQ_BASS_CUT 2 |
| |
| /* Treble boost equalizer effect */ |
| #define ASM_PARAM_EQREBLE_BOOST 3 |
| |
| /* Treble cut equalizer effect.*/ |
| #define ASM_PARAM_EQREBLE_CUT 4 |
| |
| /* Band boost equalizer effect.*/ |
| #define ASM_PARAM_EQ_BAND_BOOST 5 |
| |
| /* Band cut equalizer effect.*/ |
| #define ASM_PARAM_EQ_BAND_CUT 6 |
| |
| /* Get & set params */ |
| #define VSS_ICOMMON_CMD_SET_PARAM_V2 0x0001133D |
| #define VSS_ICOMMON_CMD_GET_PARAM_V2 0x0001133E |
| #define VSS_ICOMMON_RSP_GET_PARAM 0x00011008 |
| |
| #define VSS_MAX_AVCS_NUM_SERVICES 25 |
| |
| /* ID of the Bass Boost module. |
| * This module supports the following parameter IDs: |
| * - #AUDPROC_PARAM_ID_BASS_BOOST_ENABLE |
| * - #AUDPROC_PARAM_ID_BASS_BOOST_MODE |
| * - #AUDPROC_PARAM_ID_BASS_BOOST_STRENGTH |
| */ |
| #define AUDPROC_MODULE_ID_BASS_BOOST 0x000108A1 |
| /* ID of the Bass Boost enable parameter used by |
| * AUDPROC_MODULE_ID_BASS_BOOST. |
| */ |
| #define AUDPROC_PARAM_ID_BASS_BOOST_ENABLE 0x000108A2 |
| /* ID of the Bass Boost mode parameter used by |
| * AUDPROC_MODULE_ID_BASS_BOOST. |
| */ |
| #define AUDPROC_PARAM_ID_BASS_BOOST_MODE 0x000108A3 |
| /* ID of the Bass Boost strength parameter used by |
| * AUDPROC_MODULE_ID_BASS_BOOST. |
| */ |
| #define AUDPROC_PARAM_ID_BASS_BOOST_STRENGTH 0x000108A4 |
| |
| /* ID of the PBE module. |
| * This module supports the following parameter IDs: |
| * - #AUDPROC_PARAM_ID_PBE_ENABLE |
| * - #AUDPROC_PARAM_ID_PBE_PARAM_CONFIG |
| */ |
| #define AUDPROC_MODULE_ID_PBE 0x00010C2A |
| /* ID of the Bass Boost enable parameter used by |
| * AUDPROC_MODULE_ID_BASS_BOOST. |
| */ |
| #define AUDPROC_PARAM_ID_PBE_ENABLE 0x00010C2B |
| /* ID of the Bass Boost mode parameter used by |
| * AUDPROC_MODULE_ID_BASS_BOOST. |
| */ |
| #define AUDPROC_PARAM_ID_PBE_PARAM_CONFIG 0x00010C49 |
| |
| /* ID of the Virtualizer module. This module supports the |
| * following parameter IDs: |
| * - #AUDPROC_PARAM_ID_VIRTUALIZER_ENABLE |
| * - #AUDPROC_PARAM_ID_VIRTUALIZER_STRENGTH |
| * - #AUDPROC_PARAM_ID_VIRTUALIZER_OUT_TYPE |
| * - #AUDPROC_PARAM_ID_VIRTUALIZER_GAIN_ADJUST |
| */ |
| #define AUDPROC_MODULE_ID_VIRTUALIZER 0x000108A5 |
| /* ID of the Virtualizer enable parameter used by |
| * AUDPROC_MODULE_ID_VIRTUALIZER. |
| */ |
| #define AUDPROC_PARAM_ID_VIRTUALIZER_ENABLE 0x000108A6 |
| /* ID of the Virtualizer strength parameter used by |
| * AUDPROC_MODULE_ID_VIRTUALIZER. |
| */ |
| #define AUDPROC_PARAM_ID_VIRTUALIZER_STRENGTH 0x000108A7 |
| /* ID of the Virtualizer out type parameter used by |
| * AUDPROC_MODULE_ID_VIRTUALIZER. |
| */ |
| #define AUDPROC_PARAM_ID_VIRTUALIZER_OUT_TYPE 0x000108A8 |
| /* ID of the Virtualizer out type parameter used by |
| * AUDPROC_MODULE_ID_VIRTUALIZER. |
| */ |
| #define AUDPROC_PARAM_ID_VIRTUALIZER_GAIN_ADJUST 0x000108A9 |
| |
| /* ID of the Reverb module. This module supports the following |
| * parameter IDs: |
| * - #AUDPROC_PARAM_ID_REVERB_ENABLE |
| * - #AUDPROC_PARAM_ID_REVERB_MODE |
| * - #AUDPROC_PARAM_ID_REVERB_PRESET |
| * - #AUDPROC_PARAM_ID_REVERB_WET_MIX |
| * - #AUDPROC_PARAM_ID_REVERB_GAIN_ADJUST |
| * - #AUDPROC_PARAM_ID_REVERB_ROOM_LEVEL |
| * - #AUDPROC_PARAM_ID_REVERB_ROOM_HF_LEVEL |
| * - #AUDPROC_PARAM_ID_REVERB_DECAY_TIME |
| * - #AUDPROC_PARAM_ID_REVERB_DECAY_HF_RATIO |
| * - #AUDPROC_PARAM_ID_REVERB_REFLECTIONS_LEVEL |
| * - #AUDPROC_PARAM_ID_REVERB_REFLECTIONS_DELAY |
| * - #AUDPROC_PARAM_ID_REVERB_LEVEL |
| * - #AUDPROC_PARAM_ID_REVERB_DELAY |
| * - #AUDPROC_PARAM_ID_REVERB_DIFFUSION |
| * - #AUDPROC_PARAM_ID_REVERB_DENSITY |
| */ |
| #define AUDPROC_MODULE_ID_REVERB 0x000108AA |
| /* ID of the Reverb enable parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_ENABLE 0x000108AB |
| /* ID of the Reverb mode parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_MODE 0x000108AC |
| /* ID of the Reverb preset parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_PRESET 0x000108AD |
| /* ID of the Reverb wet mix parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_WET_MIX 0x000108AE |
| /* ID of the Reverb gain adjust parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_GAIN_ADJUST 0x000108AF |
| /* ID of the Reverb room level parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_ROOM_LEVEL 0x000108B0 |
| /* ID of the Reverb room hf level parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_ROOM_HF_LEVEL 0x000108B1 |
| /* ID of the Reverb decay time parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_DECAY_TIME 0x000108B2 |
| /* ID of the Reverb decay hf ratio parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_DECAY_HF_RATIO 0x000108B3 |
| /* ID of the Reverb reflections level parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_REFLECTIONS_LEVEL 0x000108B4 |
| /* ID of the Reverb reflections delay parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_REFLECTIONS_DELAY 0x000108B5 |
| /* ID of the Reverb level parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_LEVEL 0x000108B6 |
| /* ID of the Reverb delay parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_DELAY 0x000108B7 |
| /* ID of the Reverb diffusion parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_DIFFUSION 0x000108B8 |
| /* ID of the Reverb density parameter used by |
| * AUDPROC_MODULE_ID_REVERB. |
| */ |
| #define AUDPROC_PARAM_ID_REVERB_DENSITY 0x000108B9 |
| |
| /* ID of the Popless Equalizer module. This module supports the |
| * following parameter IDs: |
| * - #AUDPROC_PARAM_ID_EQ_ENABLE |
| * - #AUDPROC_PARAM_ID_EQ_CONFIG |
| * - #AUDPROC_PARAM_ID_EQ_NUM_BANDS |
| * - #AUDPROC_PARAM_ID_EQ_BAND_LEVELS |
| * - #AUDPROC_PARAM_ID_EQ_BAND_LEVEL_RANGE |
| * - #AUDPROC_PARAM_ID_EQ_BAND_FREQS |
| * - #AUDPROC_PARAM_ID_EQ_SINGLE_BAND_FREQ_RANGE |
| * - #AUDPROC_PARAM_ID_EQ_SINGLE_BAND_FREQ |
| * - #AUDPROC_PARAM_ID_EQ_BAND_INDEX |
| * - #AUDPROC_PARAM_ID_EQ_PRESET_ID |
| * - #AUDPROC_PARAM_ID_EQ_NUM_PRESETS |
| * - #AUDPROC_PARAM_ID_EQ_GET_PRESET_NAME |
| */ |
| #define AUDPROC_MODULE_ID_POPLESS_EQUALIZER 0x000108BA |
| /* ID of the Popless Equalizer enable parameter used by |
| * AUDPROC_MODULE_ID_POPLESS_EQUALIZER. |
| */ |
| #define AUDPROC_PARAM_ID_EQ_ENABLE 0x000108BB |
| /* ID of the Popless Equalizer config parameter used by |
| * AUDPROC_MODULE_ID_POPLESS_EQUALIZER. |
| */ |
| #define AUDPROC_PARAM_ID_EQ_CONFIG 0x000108BC |
| /* ID of the Popless Equalizer number of bands parameter used |
| * by AUDPROC_MODULE_ID_POPLESS_EQUALIZER. This param ID is |
| * used for get param only. |
| */ |
| #define AUDPROC_PARAM_ID_EQ_NUM_BANDS 0x000108BD |
| /* ID of the Popless Equalizer band levels parameter used by |
| * AUDPROC_MODULE_ID_POPLESS_EQUALIZER. This param ID is |
| * used for get param only. |
| */ |
| #define AUDPROC_PARAM_ID_EQ_BAND_LEVELS 0x000108BE |
| /* ID of the Popless Equalizer band level range parameter used |
| * by AUDPROC_MODULE_ID_POPLESS_EQUALIZER. This param ID is |
| * used for get param only. |
| */ |
| #define AUDPROC_PARAM_ID_EQ_BAND_LEVEL_RANGE 0x000108BF |
| /* ID of the Popless Equalizer band frequencies parameter used |
| * by AUDPROC_MODULE_ID_POPLESS_EQUALIZER. This param ID is |
| * used for get param only. |
| */ |
| #define AUDPROC_PARAM_ID_EQ_BAND_FREQS 0x000108C0 |
| /* ID of the Popless Equalizer single band frequency range |
| * parameter used by AUDPROC_MODULE_ID_POPLESS_EQUALIZER. |
| * This param ID is used for get param only. |
| */ |
| #define AUDPROC_PARAM_ID_EQ_SINGLE_BAND_FREQ_RANGE 0x000108C1 |
| /* ID of the Popless Equalizer single band frequency parameter |
| * used by AUDPROC_MODULE_ID_POPLESS_EQUALIZER. This param ID |
| * is used for set param only. |
| */ |
| #define AUDPROC_PARAM_ID_EQ_SINGLE_BAND_FREQ 0x000108C2 |
| /* ID of the Popless Equalizer band index parameter used by |
| * AUDPROC_MODULE_ID_POPLESS_EQUALIZER. |
| */ |
| #define AUDPROC_PARAM_ID_EQ_BAND_INDEX 0x000108C3 |
| /* ID of the Popless Equalizer preset id parameter used by |
| * AUDPROC_MODULE_ID_POPLESS_EQUALIZER. This param ID is used |
| * for get param only. |
| */ |
| #define AUDPROC_PARAM_ID_EQ_PRESET_ID 0x000108C4 |
| /* ID of the Popless Equalizer number of presets parameter used |
| * by AUDPROC_MODULE_ID_POPLESS_EQUALIZER. This param ID is used |
| * for get param only. |
| */ |
| #define AUDPROC_PARAM_ID_EQ_NUM_PRESETS 0x000108C5 |
| /* ID of the Popless Equalizer preset name parameter used by |
| * AUDPROC_MODULE_ID_POPLESS_EQUALIZER. This param ID is used |
| * for get param only. |
| */ |
| #define AUDPROC_PARAM_ID_EQ_PRESET_NAME 0x000108C6 |
| |
| /* Set Q6 topologies */ |
| #define ASM_CMD_ADD_TOPOLOGIES 0x00010DBE |
| #define ADM_CMD_ADD_TOPOLOGIES 0x00010335 |
| #define AFE_CMD_ADD_TOPOLOGIES 0x000100f8 |
| /* structure used for both ioctls */ |
| struct cmd_set_topologies { |
| struct apr_hdr hdr; |
| u32 payload_addr_lsw; |
| /* LSW of parameter data payload address.*/ |
| u32 payload_addr_msw; |
| /* MSW of parameter data payload address.*/ |
| u32 mem_map_handle; |
| /* Memory map handle returned by mem map command */ |
| u32 payload_size; |
| /* Size in bytes of the variable payload in shared memory */ |
| } __packed; |
| |
| /* This module represents the Rx processing of Feedback speaker protection. |
| * It contains the excursion control, thermal protection, |
| * analog clip manager features in it. |
| * This module id will support following param ids. |
| * - AFE_PARAM_ID_FBSP_MODE_RX_CFG |
| */ |
| |
| #define AFE_MODULE_FB_SPKR_PROT_RX 0x0001021C |
| #define AFE_MODULE_FB_SPKR_PROT_V2_RX 0x0001025F |
| #define AFE_PARAM_ID_SP_RX_LIMITER_TH 0x000102B1 |
| #define AFE_PARAM_ID_FBSP_MODE_RX_CFG 0x0001021D |
| #define AFE_PARAM_ID_FBSP_PTONE_RAMP_CFG 0x00010260 |
| |
| struct asm_fbsp_mode_rx_cfg { |
| uint32_t minor_version; |
| uint32_t mode; |
| } __packed; |
| |
| /* This module represents the VI processing of feedback speaker protection. |
| * It will receive Vsens and Isens from codec and generates necessary |
| * parameters needed by Rx processing. |
| * This module id will support following param ids. |
| * - AFE_PARAM_ID_SPKR_CALIB_VI_PROC_CFG |
| * - AFE_PARAM_ID_CALIB_RES_CFG |
| * - AFE_PARAM_ID_FEEDBACK_PATH_CFG |
| */ |
| |
| #define AFE_MODULE_FB_SPKR_PROT_VI_PROC 0x00010226 |
| #define AFE_MODULE_FB_SPKR_PROT_VI_PROC_V2 0x0001026A |
| |
| #define AFE_PARAM_ID_SPKR_CALIB_VI_PROC_CFG 0x0001022A |
| #define AFE_PARAM_ID_SPKR_CALIB_VI_PROC_CFG_V2 0x0001026B |
| |
| struct asm_spkr_calib_vi_proc_cfg { |
| uint32_t minor_version; |
| uint32_t operation_mode; |
| uint32_t r0_t0_selection_flag[SP_V2_NUM_MAX_SPKR]; |
| int32_t r0_cali_q24[SP_V2_NUM_MAX_SPKR]; |
| int16_t t0_cali_q6[SP_V2_NUM_MAX_SPKR]; |
| uint32_t quick_calib_flag; |
| } __packed; |
| |
| #define AFE_PARAM_ID_CALIB_RES_CFG 0x0001022B |
| #define AFE_PARAM_ID_CALIB_RES_CFG_V2 0x0001026E |
| |
| struct asm_calib_res_cfg { |
| uint32_t minor_version; |
| int32_t r0_cali_q24[SP_V2_NUM_MAX_SPKR]; |
| uint32_t th_vi_ca_state; |
| } __packed; |
| |
| #define AFE_PARAM_ID_FEEDBACK_PATH_CFG 0x0001022C |
| #define AFE_MODULE_FEEDBACK 0x00010257 |
| |
| struct asm_feedback_path_cfg { |
| uint32_t minor_version; |
| int32_t dst_portid; |
| int32_t num_channels; |
| int32_t chan_info[4]; |
| } __packed; |
| |
| #define AFE_PARAM_ID_MODE_VI_PROC_CFG 0x00010227 |
| |
| struct asm_mode_vi_proc_cfg { |
| uint32_t minor_version; |
| uint32_t cal_mode; |
| } __packed; |
| |
| #define AFE_MODULE_SPEAKER_PROTECTION_V2_TH_VI 0x0001026A |
| #define AFE_PARAM_ID_SP_V2_TH_VI_MODE_CFG 0x0001026B |
| #define AFE_PARAM_ID_SP_V2_TH_VI_FTM_CFG 0x0001029F |
| #define AFE_PARAM_ID_SP_V2_TH_VI_FTM_PARAMS 0x000102A0 |
| |
| struct afe_sp_th_vi_mode_cfg { |
| uint32_t minor_version; |
| uint32_t operation_mode; |
| /* |
| * Operation mode of thermal VI module. |
| * 0 -- Normal Running mode |
| * 1 -- Calibration mode |
| * 2 -- FTM mode |
| */ |
| uint32_t r0t0_selection_flag[SP_V2_NUM_MAX_SPKR]; |
| /* |
| * Specifies which set of R0, T0 values the algorithm will use. |
| * This field is valid only in Normal mode (operation_mode = 0). |
| * 0 -- Use calibrated R0, T0 value |
| * 1 -- Use safe R0, T0 value |
| */ |
| int32_t r0_cali_q24[SP_V2_NUM_MAX_SPKR]; |
| /* |
| * Calibration point resistance per device. This field is valid |
| * only in Normal mode (operation_mode = 0). |
| * values 33554432 to 1073741824 Ohms (in Q24 format) |
| */ |
| int16_t t0_cali_q6[SP_V2_NUM_MAX_SPKR]; |
| /* |
| * Calibration point temperature per device. This field is valid |
| * in both Normal mode and Calibration mode. |
| * values -1920 to 5120 degrees C (in Q6 format) |
| */ |
| uint32_t quick_calib_flag; |
| /* |
| * Indicates whether calibration is to be done in quick mode or not. |
| * This field is valid only in Calibration mode (operation_mode = 1). |
| * 0 -- Disabled |
| * 1 -- Enabled |
| */ |
| } __packed; |
| |
| struct afe_sp_th_vi_ftm_cfg { |
| uint32_t minor_version; |
| uint32_t wait_time_ms[SP_V2_NUM_MAX_SPKR]; |
| /* |
| * Wait time to heat up speaker before collecting statistics |
| * for ftm mode in ms. |
| * values 0 to 4294967295 ms |
| */ |
| uint32_t ftm_time_ms[SP_V2_NUM_MAX_SPKR]; |
| /* |
| * duration for which FTM statistics are collected in ms. |
| * values 0 to 2000 ms |
| */ |
| } __packed; |
| |
| struct afe_sp_th_vi_ftm_params { |
| uint32_t minor_version; |
| int32_t dc_res_q24[SP_V2_NUM_MAX_SPKR]; |
| /* |
| * DC resistance value in q24 format |
| * values 0 to 2147483647 Ohms (in Q24 format) |
| */ |
| int32_t temp_q22[SP_V2_NUM_MAX_SPKR]; |
| /* |
| * temperature value in q22 format |
| * values -125829120 to 2147483647 degC (in Q22 format) |
| */ |
| uint32_t status[SP_V2_NUM_MAX_SPKR]; |
| /* |
| * FTM packet status |
| * 0 - Incorrect operation mode.This status is returned |
| * when GET_PARAM is called in non FTM Mode |
| * 1 - Inactive mode -- Port is not yet started. |
| * 2 - Wait state. wait_time_ms has not yet elapsed |
| * 3 - In progress state. ftm_time_ms has not yet elapsed. |
| * 4 - Success. |
| * 5 - Failed. |
| */ |
| } __packed; |
| |
| struct afe_sp_th_vi_get_param { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_get_param_v2 get_param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_sp_th_vi_ftm_params param; |
| } __packed; |
| |
| struct afe_sp_th_vi_get_param_resp { |
| uint32_t status; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_sp_th_vi_ftm_params param; |
| } __packed; |
| |
| |
| #define AFE_MODULE_SPEAKER_PROTECTION_V2_EX_VI 0x0001026F |
| #define AFE_PARAM_ID_SP_V2_EX_VI_MODE_CFG 0x000102A1 |
| #define AFE_PARAM_ID_SP_V2_EX_VI_FTM_CFG 0x000102A2 |
| #define AFE_PARAM_ID_SP_V2_EX_VI_FTM_PARAMS 0x000102A3 |
| |
| struct afe_sp_ex_vi_mode_cfg { |
| uint32_t minor_version; |
| uint32_t operation_mode; |
| /* |
| * Operation mode of Excursion VI module. |
| * 0 - Normal Running mode |
| * 2 - FTM mode |
| */ |
| } __packed; |
| |
| struct afe_sp_ex_vi_ftm_cfg { |
| uint32_t minor_version; |
| uint32_t wait_time_ms[SP_V2_NUM_MAX_SPKR]; |
| /* |
| * Wait time to heat up speaker before collecting statistics |
| * for ftm mode in ms. |
| * values 0 to 4294967295 ms |
| */ |
| uint32_t ftm_time_ms[SP_V2_NUM_MAX_SPKR]; |
| /* |
| * duration for which FTM statistics are collected in ms. |
| * values 0 to 2000 ms |
| */ |
| } __packed; |
| |
| struct afe_sp_ex_vi_ftm_params { |
| uint32_t minor_version; |
| int32_t freq_q20[SP_V2_NUM_MAX_SPKR]; |
| /* |
| * Resonance frequency in q20 format |
| * values 0 to 2147483647 Hz (in Q20 format) |
| */ |
| int32_t resis_q24[SP_V2_NUM_MAX_SPKR]; |
| /* |
| * Mechanical resistance in q24 format |
| * values 0 to 2147483647 Ohms (in Q24 format) |
| */ |
| int32_t qmct_q24[SP_V2_NUM_MAX_SPKR]; |
| /* |
| * Mechanical Qfactor in q24 format |
| * values 0 to 2147483647 (in Q24 format) |
| */ |
| uint32_t status[SP_V2_NUM_MAX_SPKR]; |
| /* |
| * FTM packet status |
| * 0 - Incorrect operation mode.This status is returned |
| * when GET_PARAM is called in non FTM Mode. |
| * 1 - Inactive mode -- Port is not yet started. |
| * 2 - Wait state. wait_time_ms has not yet elapsed |
| * 3 - In progress state. ftm_time_ms has not yet elapsed. |
| * 4 - Success. |
| * 5 - Failed. |
| */ |
| } __packed; |
| |
| struct afe_sp_ex_vi_get_param { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_get_param_v2 get_param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_sp_ex_vi_ftm_params param; |
| } __packed; |
| |
| struct afe_sp_ex_vi_get_param_resp { |
| uint32_t status; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_sp_ex_vi_ftm_params param; |
| } __packed; |
| |
| struct afe_sp_rx_limiter_th_param { |
| uint32_t minor_version; |
| uint32_t lim_thr_per_calib_q27[SP_V2_NUM_MAX_SPKR]; |
| } __packed; |
| |
| union afe_spkr_prot_config { |
| struct asm_fbsp_mode_rx_cfg mode_rx_cfg; |
| struct asm_spkr_calib_vi_proc_cfg vi_proc_cfg; |
| struct asm_feedback_path_cfg feedback_path_cfg; |
| struct asm_mode_vi_proc_cfg mode_vi_proc_cfg; |
| struct afe_sp_th_vi_mode_cfg th_vi_mode_cfg; |
| struct afe_sp_th_vi_ftm_cfg th_vi_ftm_cfg; |
| struct afe_sp_ex_vi_mode_cfg ex_vi_mode_cfg; |
| struct afe_sp_ex_vi_ftm_cfg ex_vi_ftm_cfg; |
| struct afe_sp_rx_limiter_th_param limiter_th_cfg; |
| } __packed; |
| |
| struct afe_spkr_prot_config_command { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| union afe_spkr_prot_config prot_config; |
| } __packed; |
| |
| struct afe_spkr_prot_get_vi_calib { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_get_param_v2 get_param; |
| struct afe_port_param_data_v2 pdata; |
| struct asm_calib_res_cfg res_cfg; |
| } __packed; |
| |
| struct afe_spkr_prot_calib_get_resp { |
| uint32_t status; |
| struct afe_port_param_data_v2 pdata; |
| struct asm_calib_res_cfg res_cfg; |
| } __packed; |
| |
| |
| /* SRS TRUMEDIA start */ |
| /* topology */ |
| #define SRS_TRUMEDIA_TOPOLOGY_ID 0x00010D90 |
| /* module */ |
| #define SRS_TRUMEDIA_MODULE_ID 0x10005010 |
| /* parameters */ |
| #define SRS_TRUMEDIA_PARAMS 0x10005011 |
| #define SRS_TRUMEDIA_PARAMS_WOWHD 0x10005012 |
| #define SRS_TRUMEDIA_PARAMS_CSHP 0x10005013 |
| #define SRS_TRUMEDIA_PARAMS_HPF 0x10005014 |
| #define SRS_TRUMEDIA_PARAMS_AEQ 0x10005015 |
| #define SRS_TRUMEDIA_PARAMS_HL 0x10005016 |
| #define SRS_TRUMEDIA_PARAMS_GEQ 0x10005017 |
| |
| #define SRS_ID_GLOBAL 0x00000001 |
| #define SRS_ID_WOWHD 0x00000002 |
| #define SRS_ID_CSHP 0x00000003 |
| #define SRS_ID_HPF 0x00000004 |
| #define SRS_ID_AEQ 0x00000005 |
| #define SRS_ID_HL 0x00000006 |
| #define SRS_ID_GEQ 0x00000007 |
| |
| #define SRS_CMD_UPLOAD 0x7FFF0000 |
| #define SRS_PARAM_OFFSET_MASK 0x3FFF0000 |
| #define SRS_PARAM_VALUE_MASK 0x0000FFFF |
| |
| struct srs_trumedia_params_GLOBAL { |
| uint8_t v1; |
| uint8_t v2; |
| uint8_t v3; |
| uint8_t v4; |
| uint8_t v5; |
| uint8_t v6; |
| uint8_t v7; |
| uint8_t v8; |
| uint16_t v9; |
| } __packed; |
| |
| struct srs_trumedia_params_WOWHD { |
| uint32_t v1; |
| uint16_t v2; |
| uint16_t v3; |
| uint16_t v4; |
| uint16_t v5; |
| uint16_t v6; |
| uint16_t v7; |
| uint16_t v8; |
| uint16_t v____A1; |
| uint32_t v9; |
| uint16_t v10; |
| uint16_t v11; |
| uint32_t v12[16]; |
| uint32_t v13[16]; |
| uint32_t v14[16]; |
| uint32_t v15[16]; |
| uint32_t v16; |
| uint16_t v17; |
| uint16_t v18; |
| } __packed; |
| |
| struct srs_trumedia_params_CSHP { |
| uint32_t v1; |
| uint16_t v2; |
| uint16_t v3; |
| uint16_t v4; |
| uint16_t v5; |
| uint16_t v6; |
| uint16_t v____A1; |
| uint32_t v7; |
| uint16_t v8; |
| uint16_t v9; |
| uint32_t v10[16]; |
| } __packed; |
| |
| struct srs_trumedia_params_HPF { |
| uint32_t v1; |
| uint32_t v2[26]; |
| } __packed; |
| |
| struct srs_trumedia_params_AEQ { |
| uint32_t v1; |
| uint16_t v2; |
| uint16_t v3; |
| uint16_t v4; |
| uint16_t v____A1; |
| uint32_t v5[74]; |
| uint32_t v6[74]; |
| uint16_t v7[2048]; |
| } __packed; |
| |
| struct srs_trumedia_params_HL { |
| uint16_t v1; |
| uint16_t v2; |
| uint16_t v3; |
| uint16_t v____A1; |
| int32_t v4; |
| uint32_t v5; |
| uint16_t v6; |
| uint16_t v____A2; |
| uint32_t v7; |
| } __packed; |
| |
| struct srs_trumedia_params_GEQ { |
| int16_t v1[10]; |
| } __packed; |
| struct srs_trumedia_params { |
| struct srs_trumedia_params_GLOBAL global; |
| struct srs_trumedia_params_WOWHD wowhd; |
| struct srs_trumedia_params_CSHP cshp; |
| struct srs_trumedia_params_HPF hpf; |
| struct srs_trumedia_params_AEQ aeq; |
| struct srs_trumedia_params_HL hl; |
| struct srs_trumedia_params_GEQ geq; |
| } __packed; |
| /* SRS TruMedia end */ |
| |
| #define AUDPROC_PARAM_ID_ENABLE 0x00010904 |
| #define ASM_STREAM_POSTPROC_TOPO_ID_SA_PLUS 0x1000FFFF |
| /* DTS Eagle */ |
| #define AUDPROC_MODULE_ID_DTS_HPX_PREMIX 0x0001077C |
| #define AUDPROC_MODULE_ID_DTS_HPX_POSTMIX 0x0001077B |
| #define ASM_STREAM_POSTPROC_TOPO_ID_DTS_HPX 0x00010DED |
| #define ASM_STREAM_POSTPROC_TOPO_ID_HPX_PLUS 0x10015000 |
| #define ASM_STREAM_POSTPROC_TOPO_ID_HPX_MASTER 0x10015001 |
| struct asm_dts_eagle_param { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_pp_params_v2 param; |
| struct asm_stream_param_data_v2 data; |
| } __packed; |
| |
| struct asm_dts_eagle_param_get { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_get_pp_params_v2 param; |
| } __packed; |
| |
| /* Opcode to set BT address and license for aptx decoder */ |
| #define APTX_DECODER_BT_ADDRESS 0x00013201 |
| #define APTX_CLASSIC_DEC_LICENSE_ID 0x00013202 |
| |
| struct aptx_dec_bt_addr_cfg { |
| uint32_t lap; |
| uint32_t uap; |
| uint32_t nap; |
| } __packed; |
| |
| struct aptx_dec_bt_dev_addr { |
| struct apr_hdr hdr; |
| struct asm_stream_cmd_set_encdec_param encdec; |
| struct aptx_dec_bt_addr_cfg bt_addr_cfg; |
| } __packed; |
| |
| struct asm_aptx_dec_fmt_blk_v2 { |
| struct apr_hdr hdr; |
| struct asm_data_cmd_media_fmt_update_v2 fmtblk; |
| u32 sample_rate; |
| /* Number of samples per second. |
| * Supported values: 44100 and 48000 Hz |
| */ |
| } __packed; |
| |
| /* Q6Core Specific */ |
| #define AVCS_CMD_GET_FWK_VERSION (0x0001292C) |
| #define AVCS_CMDRSP_GET_FWK_VERSION (0x0001292D) |
| |
| #define AVCS_SERVICE_ID_ALL (0xFFFFFFFF) |
| #define AVCS_SERVICE_ID_AFE (0x4) |
| #define APRV2_IDS_SERVICE_ID_ADSP_CVP_V (0xB) |
| |
| struct avcs_get_fwk_version { |
| /* |
| * Indicates the major version of the AVS build. |
| * This value is incremented on chipset family boundaries. |
| */ |
| uint32_t build_major_version; |
| |
| /* |
| * Minor version of the AVS build. |
| * This value represents the mainline to which the AVS build belongs. |
| */ |
| uint32_t build_minor_version; |
| |
| /* Indicates the AVS branch version to which the image belongs. */ |
| uint32_t build_branch_version; |
| |
| /* Indicates the AVS sub-branch or customer product line information. */ |
| uint32_t build_subbranch_version; |
| |
| /* Number of supported AVS services in the current build. */ |
| uint32_t num_services; |
| }; |
| |
| struct avs_svc_api_info { |
| /* |
| * APRV2 service IDs for the individual static services. |
| * |
| * @values |
| * - APRV2_IDS_SERVICE_ID_ADSP_CORE_V |
| * - APRV2_IDS_SERVICE_ID_ADSP_AFE_V |
| * - APRV2_IDS_SERVICE_ID_ADSP_ASM_V |
| * - APRV2_IDS_SERVICE_ID_ADSP_ADM_V |
| * - APRV2_IDS_SERVICE_ID_ADSP_MVM_V |
| * - APRV2_IDS_SERVICE_ID_ADSP_CVS_V |
| * - APRV2_IDS_SERVICE_ID_ADSP_CVP_V |
| * - APRV2_IDS_SERVICE_ID_ADSP_LSM_V |
| */ |
| uint32_t service_id; |
| |
| /* |
| * Indicates the API version of the service. |
| * |
| * Each new API update that warrants a change on the HLOS side triggers |
| * an increment in the version. |
| */ |
| uint32_t api_version; |
| |
| /* |
| * Indicates the API increments on a sub-branch (not on the mainline). |
| * |
| * API branch version numbers can increment independently on different |
| * sub-branches. |
| */ |
| uint32_t api_branch_version; |
| }; |
| |
| struct avcs_fwk_ver_info { |
| struct avcs_get_fwk_version avcs_fwk_version; |
| struct avs_svc_api_info services[0]; |
| } __packed; |
| |
| /* LSM Specific */ |
| #define VW_FEAT_DIM (39) |
| |
| #define APRV2_IDS_SERVICE_ID_ADSP_LSM_V (0xD) |
| #define APRV2_IDS_DOMAIN_ID_ADSP_V (0x4) |
| #define APRV2_IDS_DOMAIN_ID_APPS_V (0x5) |
| |
| #define LSM_SESSION_CMD_SHARED_MEM_MAP_REGIONS (0x00012A7F) |
| #define LSM_SESSION_CMDRSP_SHARED_MEM_MAP_REGIONS (0x00012A80) |
| #define LSM_SESSION_CMD_SHARED_MEM_UNMAP_REGIONS (0x00012A81) |
| #define LSM_SESSION_CMD_OPEN_TX (0x00012A82) |
| #define LSM_SESSION_CMD_CLOSE_TX (0x00012A88) |
| #define LSM_SESSION_CMD_SET_PARAMS (0x00012A83) |
| #define LSM_SESSION_CMD_SET_PARAMS_V2 (0x00012A8F) |
| #define LSM_SESSION_CMD_REGISTER_SOUND_MODEL (0x00012A84) |
| #define LSM_SESSION_CMD_DEREGISTER_SOUND_MODEL (0x00012A85) |
| #define LSM_SESSION_CMD_START (0x00012A86) |
| #define LSM_SESSION_CMD_STOP (0x00012A87) |
| #define LSM_SESSION_CMD_EOB (0x00012A89) |
| #define LSM_SESSION_CMD_READ (0x00012A8A) |
| #define LSM_SESSION_CMD_OPEN_TX_V2 (0x00012A8B) |
| #define LSM_CMD_ADD_TOPOLOGIES (0x00012A8C) |
| |
| #define LSM_SESSION_EVENT_DETECTION_STATUS (0x00012B00) |
| #define LSM_SESSION_EVENT_DETECTION_STATUS_V2 (0x00012B01) |
| #define LSM_DATA_EVENT_READ_DONE (0x00012B02) |
| #define LSM_DATA_EVENT_STATUS (0x00012B03) |
| #define LSM_SESSION_EVENT_DETECTION_STATUS_V3 (0x00012B04) |
| |
| #define LSM_MODULE_ID_VOICE_WAKEUP (0x00012C00) |
| #define LSM_PARAM_ID_ENDPOINT_DETECT_THRESHOLD (0x00012C01) |
| #define LSM_PARAM_ID_OPERATION_MODE (0x00012C02) |
| #define LSM_PARAM_ID_GAIN (0x00012C03) |
| #define LSM_PARAM_ID_CONNECT_TO_PORT (0x00012C04) |
| #define LSM_PARAM_ID_FEATURE_COMPENSATION_DATA (0x00012C07) |
| #define LSM_PARAM_ID_MIN_CONFIDENCE_LEVELS (0x00012C07) |
| #define LSM_MODULE_ID_LAB (0x00012C08) |
| #define LSM_PARAM_ID_LAB_ENABLE (0x00012C09) |
| #define LSM_PARAM_ID_LAB_CONFIG (0x00012C0A) |
| #define LSM_MODULE_ID_FRAMEWORK (0x00012C0E) |
| #define LSM_PARAM_ID_SWMAD_CFG (0x00012C18) |
| #define LSM_PARAM_ID_SWMAD_MODEL (0x00012C19) |
| #define LSM_PARAM_ID_SWMAD_ENABLE (0x00012C1A) |
| #define LSM_PARAM_ID_POLLING_ENABLE (0x00012C1B) |
| #define LSM_PARAM_ID_MEDIA_FMT (0x00012C1E) |
| #define LSM_PARAM_ID_FWK_MODE_CONFIG (0x00012C27) |
| |
| /* HW MAD specific */ |
| #define AFE_MODULE_HW_MAD (0x00010230) |
| #define AFE_PARAM_ID_HW_MAD_CFG (0x00010231) |
| #define AFE_PARAM_ID_HW_MAD_CTRL (0x00010232) |
| #define AFE_PARAM_ID_SLIMBUS_SLAVE_PORT_CFG (0x00010233) |
| |
| /* SW MAD specific */ |
| #define AFE_MODULE_SW_MAD (0x0001022D) |
| #define AFE_PARAM_ID_SW_MAD_CFG (0x0001022E) |
| #define AFE_PARAM_ID_SVM_MODEL (0x0001022F) |
| |
| /* Commands/Params to pass the codec/slimbus data to DSP */ |
| #define AFE_SVC_CMD_SET_PARAM (0x000100f3) |
| #define AFE_MODULE_CDC_DEV_CFG (0x00010234) |
| #define AFE_PARAM_ID_CDC_SLIMBUS_SLAVE_CFG (0x00010235) |
| #define AFE_PARAM_ID_CDC_REG_CFG (0x00010236) |
| #define AFE_PARAM_ID_CDC_REG_CFG_INIT (0x00010237) |
| #define AFE_PARAM_ID_CDC_REG_PAGE_CFG (0x00010296) |
| |
| #define AFE_MAX_CDC_REGISTERS_TO_CONFIG (20) |
| |
| /* AANC Port Config Specific */ |
| #define AFE_PARAM_ID_AANC_PORT_CONFIG (0x00010215) |
| #define AFE_API_VERSION_AANC_PORT_CONFIG (0x1) |
| #define AANC_TX_MIC_UNUSED (0) |
| #define AANC_TX_VOICE_MIC (1) |
| #define AANC_TX_ERROR_MIC (2) |
| #define AANC_TX_NOISE_MIC (3) |
| #define AFE_PORT_MAX_CHANNEL_CNT (8) |
| #define AFE_MODULE_AANC (0x00010214) |
| #define AFE_PARAM_ID_CDC_AANC_VERSION (0x0001023A) |
| #define AFE_API_VERSION_CDC_AANC_VERSION (0x1) |
| #define AANC_HW_BLOCK_VERSION_1 (1) |
| #define AANC_HW_BLOCK_VERSION_2 (2) |
| |
| /*Clip bank selection*/ |
| #define AFE_API_VERSION_CLIP_BANK_SEL_CFG 0x1 |
| #define AFE_CLIP_MAX_BANKS 4 |
| #define AFE_PARAM_ID_CLIP_BANK_SEL_CFG 0x00010242 |
| |
| struct afe_param_aanc_port_cfg { |
| /* Minor version used for tracking the version of the module's |
| * source port configuration. |
| */ |
| uint32_t aanc_port_cfg_minor_version; |
| |
| /* Sampling rate of the source Tx port. 8k - 192k*/ |
| uint32_t tx_port_sample_rate; |
| |
| /* Channel mapping for the Tx port signal carrying Noise (X), |
| * Error (E), and Voice (V) signals. |
| */ |
| uint8_t tx_port_channel_map[AFE_PORT_MAX_CHANNEL_CNT]; |
| |
| /* Number of channels on the source Tx port. */ |
| uint16_t tx_port_num_channels; |
| |
| /* Port ID of the Rx path reference signal. */ |
| uint16_t rx_path_ref_port_id; |
| |
| /* Sampling rate of the reference port. 8k - 192k*/ |
| uint32_t ref_port_sample_rate; |
| } __packed; |
| |
| struct afe_param_id_cdc_aanc_version { |
| /* Minor version used for tracking the version of the module's |
| * hw version |
| */ |
| uint32_t cdc_aanc_minor_version; |
| |
| /* HW version. */ |
| uint32_t aanc_hw_version; |
| } __packed; |
| |
| struct afe_param_id_clip_bank_sel { |
| /* Minor version used for tracking the version of the module's |
| * hw version |
| */ |
| uint32_t minor_version; |
| |
| /* Number of banks to be read */ |
| uint32_t num_banks; |
| |
| uint32_t bank_map[AFE_CLIP_MAX_BANKS]; |
| } __packed; |
| |
| /* ERROR CODES */ |
| /* Success. The operation completed with no errors. */ |
| #define ADSP_EOK 0x00000000 |
| /* General failure. */ |
| #define ADSP_EFAILED 0x00000001 |
| /* Bad operation parameter. */ |
| #define ADSP_EBADPARAM 0x00000002 |
| /* Unsupported routine or operation. */ |
| #define ADSP_EUNSUPPORTED 0x00000003 |
| /* Unsupported version. */ |
| #define ADSP_EVERSION 0x00000004 |
| /* Unexpected problem encountered. */ |
| #define ADSP_EUNEXPECTED 0x00000005 |
| /* Unhandled problem occurred. */ |
| #define ADSP_EPANIC 0x00000006 |
| /* Unable to allocate resource. */ |
| #define ADSP_ENORESOURCE 0x00000007 |
| /* Invalid handle. */ |
| #define ADSP_EHANDLE 0x00000008 |
| /* Operation is already processed. */ |
| #define ADSP_EALREADY 0x00000009 |
| /* Operation is not ready to be processed. */ |
| #define ADSP_ENOTREADY 0x0000000A |
| /* Operation is pending completion. */ |
| #define ADSP_EPENDING 0x0000000B |
| /* Operation could not be accepted or processed. */ |
| #define ADSP_EBUSY 0x0000000C |
| /* Operation aborted due to an error. */ |
| #define ADSP_EABORTED 0x0000000D |
| /* Operation preempted by a higher priority. */ |
| #define ADSP_EPREEMPTED 0x0000000E |
| /* Operation requests intervention to complete. */ |
| #define ADSP_ECONTINUE 0x0000000F |
| /* Operation requests immediate intervention to complete. */ |
| #define ADSP_EIMMEDIATE 0x00000010 |
| /* Operation is not implemented. */ |
| #define ADSP_ENOTIMPL 0x00000011 |
| /* Operation needs more data or resources. */ |
| #define ADSP_ENEEDMORE 0x00000012 |
| /* Operation does not have memory. */ |
| #define ADSP_ENOMEMORY 0x00000014 |
| /* Item does not exist. */ |
| #define ADSP_ENOTEXIST 0x00000015 |
| /* Max count for adsp error code sent to HLOS*/ |
| #define ADSP_ERR_MAX (ADSP_ENOTEXIST + 1) |
| /* Operation is finished. */ |
| #define ADSP_ETERMINATED 0x00011174 |
| |
| /*bharath, adsp_error_codes.h */ |
| |
| /* LPASS clock for I2S Interface */ |
| |
| /* Supported OSR clock values */ |
| #define Q6AFE_LPASS_OSR_CLK_12_P288_MHZ 0xBB8000 |
| #define Q6AFE_LPASS_OSR_CLK_11_P2896_MHZ 0xAC4400 |
| #define Q6AFE_LPASS_OSR_CLK_9_P600_MHZ 0x927C00 |
| #define Q6AFE_LPASS_OSR_CLK_8_P192_MHZ 0x7D0000 |
| #define Q6AFE_LPASS_OSR_CLK_6_P144_MHZ 0x5DC000 |
| #define Q6AFE_LPASS_OSR_CLK_4_P096_MHZ 0x3E8000 |
| #define Q6AFE_LPASS_OSR_CLK_3_P072_MHZ 0x2EE000 |
| #define Q6AFE_LPASS_OSR_CLK_2_P048_MHZ 0x1F4000 |
| #define Q6AFE_LPASS_OSR_CLK_1_P536_MHZ 0x177000 |
| #define Q6AFE_LPASS_OSR_CLK_1_P024_MHZ 0xFA000 |
| #define Q6AFE_LPASS_OSR_CLK_768_kHZ 0xBB800 |
| #define Q6AFE_LPASS_OSR_CLK_512_kHZ 0x7D000 |
| #define Q6AFE_LPASS_OSR_CLK_DISABLE 0x0 |
| |
| /* Supported Bit clock values */ |
| #define Q6AFE_LPASS_IBIT_CLK_12_P288_MHZ 0xBB8000 |
| #define Q6AFE_LPASS_IBIT_CLK_11_P2896_MHZ 0xAC4400 |
| #define Q6AFE_LPASS_IBIT_CLK_8_P192_MHZ 0x7D0000 |
| #define Q6AFE_LPASS_IBIT_CLK_6_P144_MHZ 0x5DC000 |
| #define Q6AFE_LPASS_IBIT_CLK_4_P096_MHZ 0x3E8000 |
| #define Q6AFE_LPASS_IBIT_CLK_3_P072_MHZ 0x2EE000 |
| #define Q6AFE_LPASS_IBIT_CLK_2_P8224_MHZ 0x2b1100 |
| #define Q6AFE_LPASS_IBIT_CLK_2_P048_MHZ 0x1F4000 |
| #define Q6AFE_LPASS_IBIT_CLK_1_P536_MHZ 0x177000 |
| #define Q6AFE_LPASS_IBIT_CLK_1_P4112_MHZ 0x158880 |
| #define Q6AFE_LPASS_IBIT_CLK_1_P024_MHZ 0xFA000 |
| #define Q6AFE_LPASS_IBIT_CLK_768_KHZ 0xBB800 |
| #define Q6AFE_LPASS_IBIT_CLK_512_KHZ 0x7D000 |
| #define Q6AFE_LPASS_IBIT_CLK_256_KHZ 0x3E800 |
| #define Q6AFE_LPASS_IBIT_CLK_DISABLE 0x0 |
| |
| /* Supported LPASS CLK sources */ |
| #define Q6AFE_LPASS_CLK_SRC_EXTERNAL 0 |
| #define Q6AFE_LPASS_CLK_SRC_INTERNAL 1 |
| |
| /* Supported LPASS CLK root*/ |
| #define Q6AFE_LPASS_CLK_ROOT_DEFAULT 0 |
| |
| enum afe_lpass_clk_mode { |
| Q6AFE_LPASS_MODE_BOTH_INVALID, |
| Q6AFE_LPASS_MODE_CLK1_VALID, |
| Q6AFE_LPASS_MODE_CLK2_VALID, |
| Q6AFE_LPASS_MODE_BOTH_VALID, |
| } __packed; |
| |
| /* Clock ID Enumeration Define. */ |
| /* Clock ID for Primary I2S IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_PRI_MI2S_IBIT 0x100 |
| /* Clock ID for Primary I2S EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_PRI_MI2S_EBIT 0x101 |
| /* Clock ID for Secondary I2S IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_SEC_MI2S_IBIT 0x102 |
| /* Clock ID for Secondary I2S EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_SEC_MI2S_EBIT 0x103 |
| /* Clock ID for Tertiary I2S IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_TER_MI2S_IBIT 0x104 |
| /* Clock ID for Tertiary I2S EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_TER_MI2S_EBIT 0x105 |
| /* Clock ID for Quartnery I2S IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_QUAD_MI2S_IBIT 0x106 |
| /* Clock ID for Quartnery I2S EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_QUAD_MI2S_EBIT 0x107 |
| /* Clock ID for Speaker I2S IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_SPEAKER_I2S_IBIT 0x108 |
| /* Clock ID for Speaker I2S EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_SPEAKER_I2S_EBIT 0x109 |
| /* Clock ID for Speaker I2S OSR */ |
| #define Q6AFE_LPASS_CLK_ID_SPEAKER_I2S_OSR 0x10A |
| |
| /* Clock ID for QUINARY I2S IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_QUI_MI2S_IBIT 0x10B |
| /* Clock ID for QUINARY I2S EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_QUI_MI2S_EBIT 0x10C |
| /* Clock ID for SENARY I2S IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_SEN_MI2S_IBIT 0x10D |
| /* Clock ID for SENARY I2S EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_SEN_MI2S_EBIT 0x10E |
| /* Clock ID for INT0 I2S IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_INT0_MI2S_IBIT 0x10F |
| /* Clock ID for INT1 I2S IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_INT1_MI2S_IBIT 0x110 |
| /* Clock ID for INT2 I2S IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_INT2_MI2S_IBIT 0x111 |
| /* Clock ID for INT3 I2S IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_INT3_MI2S_IBIT 0x112 |
| /* Clock ID for INT4 I2S IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_INT4_MI2S_IBIT 0x113 |
| /* Clock ID for INT5 I2S IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_INT5_MI2S_IBIT 0x114 |
| /* Clock ID for INT6 I2S IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_INT6_MI2S_IBIT 0x115 |
| |
| /* Clock ID for QUINARY MI2S OSR CLK */ |
| #define Q6AFE_LPASS_CLK_ID_QUI_MI2S_OSR 0x116 |
| |
| /* Clock ID for Primary PCM IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_PRI_PCM_IBIT 0x200 |
| /* Clock ID for Primary PCM EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_PRI_PCM_EBIT 0x201 |
| /* Clock ID for Secondary PCM IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_SEC_PCM_IBIT 0x202 |
| /* Clock ID for Secondary PCM EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_SEC_PCM_EBIT 0x203 |
| /* Clock ID for Tertiary PCM IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_TER_PCM_IBIT 0x204 |
| /* Clock ID for Tertiary PCM EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_TER_PCM_EBIT 0x205 |
| /* Clock ID for Quartery PCM IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_QUAD_PCM_IBIT 0x206 |
| /* Clock ID for Quartery PCM EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_QUAD_PCM_EBIT 0x207 |
| /* Clock ID for Quinary PCM IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_QUIN_PCM_IBIT 0x208 |
| /* Clock ID for Quinary PCM EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_QUIN_PCM_EBIT 0x209 |
| /* Clock ID for QUINARY PCM OSR */ |
| #define Q6AFE_LPASS_CLK_ID_QUI_PCM_OSR 0x20A |
| |
| /** Clock ID for Primary TDM IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_PRI_TDM_IBIT 0x200 |
| /** Clock ID for Primary TDM EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_PRI_TDM_EBIT 0x201 |
| /** Clock ID for Secondary TDM IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_SEC_TDM_IBIT 0x202 |
| /** Clock ID for Secondary TDM EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_SEC_TDM_EBIT 0x203 |
| /** Clock ID for Tertiary TDM IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_TER_TDM_IBIT 0x204 |
| /** Clock ID for Tertiary TDM EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_TER_TDM_EBIT 0x205 |
| /** Clock ID for Quartery TDM IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_QUAD_TDM_IBIT 0x206 |
| /** Clock ID for Quartery TDM EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_QUAD_TDM_EBIT 0x207 |
| /** Clock ID for Quinary TDM IBIT */ |
| #define Q6AFE_LPASS_CLK_ID_QUIN_TDM_IBIT 0x208 |
| /** Clock ID for Quinary TDM EBIT */ |
| #define Q6AFE_LPASS_CLK_ID_QUIN_TDM_EBIT 0x209 |
| /** Clock ID for Quinary TDM OSR */ |
| #define Q6AFE_LPASS_CLK_ID_QUIN_TDM_OSR 0x20A |
| |
| /* Clock ID for MCLK1 */ |
| #define Q6AFE_LPASS_CLK_ID_MCLK_1 0x300 |
| /* Clock ID for MCLK2 */ |
| #define Q6AFE_LPASS_CLK_ID_MCLK_2 0x301 |
| /* Clock ID for MCLK3 */ |
| #define Q6AFE_LPASS_CLK_ID_MCLK_3 0x302 |
| /* Clock ID for MCLK4 */ |
| #define Q6AFE_LPASS_CLK_ID_MCLK_4 0x304 |
| /* Clock ID for Internal Digital Codec Core */ |
| #define Q6AFE_LPASS_CLK_ID_INTERNAL_DIGITAL_CODEC_CORE 0x303 |
| /* Clock ID for INT MCLK0 */ |
| #define Q6AFE_LPASS_CLK_ID_INT_MCLK_0 0x305 |
| /* Clock ID for INT MCLK1 */ |
| #define Q6AFE_LPASS_CLK_ID_INT_MCLK_1 0x306 |
| /* |
| * Clock ID for soundwire NPL. |
| * This is the clock to be used to enable NPL clock for internal Soundwire. |
| */ |
| #define AFE_CLOCK_SET_CLOCK_ID_SWR_NPL_CLK 0x307 |
| |
| /* Clock ID for AHB HDMI input */ |
| #define Q6AFE_LPASS_CLK_ID_AHB_HDMI_INPUT 0x400 |
| |
| /* Clock ID for SPDIF core */ |
| #define Q6AFE_LPASS_CLK_ID_SPDIF_CORE 0x500 |
| |
| |
| /* Clock attribute for invalid use (reserved for internal usage) */ |
| #define Q6AFE_LPASS_CLK_ATTRIBUTE_INVALID 0x0 |
| /* Clock attribute for no couple case */ |
| #define Q6AFE_LPASS_CLK_ATTRIBUTE_COUPLE_NO 0x1 |
| /* Clock attribute for dividend couple case */ |
| #define Q6AFE_LPASS_CLK_ATTRIBUTE_COUPLE_DIVIDEND 0x2 |
| /* Clock attribute for divisor couple case */ |
| #define Q6AFE_LPASS_CLK_ATTRIBUTE_COUPLE_DIVISOR 0x3 |
| /* Clock attribute for invert and no couple case */ |
| #define Q6AFE_LPASS_CLK_ATTRIBUTE_INVERT_COUPLE_NO 0x4 |
| /* Clock set API version */ |
| #define Q6AFE_LPASS_CLK_CONFIG_API_VERSION 0x1 |
| |
| struct afe_clk_set { |
| /* |
| * Minor version used for tracking clock set. |
| * @values #AFE_API_VERSION_CLOCK_SET |
| */ |
| uint32_t clk_set_minor_version; |
| |
| /* |
| * Clock ID |
| * @values |
| * - 0x100 to 0x10A - MSM8996 |
| * - 0x200 to 0x207 - MSM8996 |
| * - 0x300 to 0x302 - MSM8996 @tablebulletend |
| */ |
| uint32_t clk_id; |
| |
| /* |
| * Clock frequency (in Hertz) to be set. |
| * @values |
| * - >= 0 for clock frequency to set @tablebulletend |
| */ |
| uint32_t clk_freq_in_hz; |
| |
| /* Use to specific divider for two clocks if needed. |
| * Set to Q6AFE_LPASS_CLK_ATTRIBUTE_COUPLE_NO for no divider |
| * relation clocks |
| * @values |
| * - #Q6AFE_LPASS_CLK_ATTRIBUTE_COUPLE_NO |
| * - #Q6AFE_LPASS_CLK_ATTRIBUTE_COUPLE_DIVIDEND |
| * - #Q6AFE_LPASS_CLK_ATTRIBUTE_COUPLE_DIVISOR @tablebulletend |
| */ |
| uint16_t clk_attri; |
| |
| /* |
| * Specifies the root clock source. |
| * Currently, only Q6AFE_LPASS_CLK_ROOT_DEFAULT is valid |
| * @values |
| * - 0 @tablebulletend |
| */ |
| uint16_t clk_root; |
| |
| /* |
| * for enable and disable clock. |
| * "clk_freq_in_hz", "clk_attri", and "clk_root" |
| * are ignored in disable clock case. |
| * @values |
| * - 0 -- Disabled |
| * - 1 -- Enabled @tablebulletend |
| */ |
| uint32_t enable; |
| }; |
| |
| struct afe_clk_cfg { |
| /* Minor version used for tracking the version of the I2S |
| * configuration interface. |
| * Supported values: #AFE_API_VERSION_I2S_CONFIG |
| */ |
| u32 i2s_cfg_minor_version; |
| |
| /* clk value 1 in MHz. */ |
| u32 clk_val1; |
| |
| /* clk value 2 in MHz. */ |
| u32 clk_val2; |
| |
| /* clk_src |
| * #Q6AFE_LPASS_CLK_SRC_EXTERNAL |
| * #Q6AFE_LPASS_CLK_SRC_INTERNAL |
| */ |
| |
| u16 clk_src; |
| |
| /* clk_root -0 for default */ |
| u16 clk_root; |
| |
| /* clk_set_mode |
| * #Q6AFE_LPASS_MODE_BOTH_INVALID |
| * #Q6AFE_LPASS_MODE_CLK1_VALID |
| * #Q6AFE_LPASS_MODE_CLK2_VALID |
| * #Q6AFE_LPASS_MODE_BOTH_VALID |
| */ |
| u16 clk_set_mode; |
| |
| /* This param id is used to configure I2S clk */ |
| u16 reserved; |
| } __packed; |
| |
| /* This param id is used to configure I2S clk */ |
| #define AFE_PARAM_ID_LPAIF_CLK_CONFIG 0x00010238 |
| #define AFE_MODULE_CLOCK_SET 0x0001028F |
| #define AFE_PARAM_ID_CLOCK_SET 0x00010290 |
| |
| struct afe_lpass_clk_config_command { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_clk_cfg clk_cfg; |
| } __packed; |
| |
| enum afe_lpass_digital_clk_src { |
| Q6AFE_LPASS_DIGITAL_ROOT_INVALID, |
| Q6AFE_LPASS_DIGITAL_ROOT_PRI_MI2S_OSR, |
| Q6AFE_LPASS_DIGITAL_ROOT_SEC_MI2S_OSR, |
| Q6AFE_LPASS_DIGITAL_ROOT_TER_MI2S_OSR, |
| Q6AFE_LPASS_DIGITAL_ROOT_QUAD_MI2S_OSR, |
| Q6AFE_LPASS_DIGITAL_ROOT_CDC_ROOT_CLK, |
| } __packed; |
| |
| /* This param id is used to configure internal clk */ |
| #define AFE_PARAM_ID_INTERNAL_DIGIATL_CDC_CLK_CONFIG 0x00010239 |
| |
| struct afe_digital_clk_cfg { |
| /* Minor version used for tracking the version of the I2S |
| * configuration interface. |
| * Supported values: #AFE_API_VERSION_I2S_CONFIG |
| */ |
| u32 i2s_cfg_minor_version; |
| |
| /* clk value in MHz. */ |
| u32 clk_val; |
| |
| /* INVALID |
| * PRI_MI2S_OSR |
| * SEC_MI2S_OSR |
| * TER_MI2S_OSR |
| * QUAD_MI2S_OSR |
| * DIGT_CDC_ROOT |
| */ |
| u16 clk_root; |
| |
| /* This field must be set to zero. */ |
| u16 reserved; |
| } __packed; |
| |
| |
| struct afe_lpass_digital_clk_config_command { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_digital_clk_cfg clk_cfg; |
| } __packed; |
| |
| /* |
| * Opcode for AFE to start DTMF. |
| */ |
| #define AFE_PORTS_CMD_DTMF_CTL 0x00010102 |
| |
| /** DTMF payload.*/ |
| struct afe_dtmf_generation_command { |
| struct apr_hdr hdr; |
| |
| /* |
| * Duration of the DTMF tone in ms. |
| * -1 -> continuous, |
| * 0 -> disable |
| */ |
| int64_t duration_in_ms; |
| |
| /* |
| * The DTMF high tone frequency. |
| */ |
| uint16_t high_freq; |
| |
| /* |
| * The DTMF low tone frequency. |
| */ |
| uint16_t low_freq; |
| |
| /* |
| * The DTMF volume setting |
| */ |
| uint16_t gain; |
| |
| /* |
| * The number of ports to enable/disable on. |
| */ |
| uint16_t num_ports; |
| |
| /* |
| * The Destination ports - array . |
| * For DTMF on multiple ports, portIds needs to |
| * be populated numPorts times. |
| */ |
| uint16_t port_ids; |
| |
| /* |
| * variable for 32 bit alignment of APR packet. |
| */ |
| uint16_t reserved; |
| } __packed; |
| |
| enum afe_config_type { |
| AFE_SLIMBUS_SLAVE_PORT_CONFIG, |
| AFE_SLIMBUS_SLAVE_CONFIG, |
| AFE_CDC_REGISTERS_CONFIG, |
| AFE_AANC_VERSION, |
| AFE_CDC_CLIP_REGISTERS_CONFIG, |
| AFE_CLIP_BANK_SEL, |
| AFE_CDC_REGISTER_PAGE_CONFIG, |
| AFE_MAX_CONFIG_TYPES, |
| }; |
| |
| struct afe_param_slimbus_slave_port_cfg { |
| uint32_t minor_version; |
| uint16_t slimbus_dev_id; |
| uint16_t slave_dev_pgd_la; |
| uint16_t slave_dev_intfdev_la; |
| uint16_t bit_width; |
| uint16_t data_format; |
| uint16_t num_channels; |
| uint16_t slave_port_mapping[AFE_PORT_MAX_AUDIO_CHAN_CNT]; |
| } __packed; |
| |
| struct afe_param_cdc_slimbus_slave_cfg { |
| uint32_t minor_version; |
| uint32_t device_enum_addr_lsw; |
| uint32_t device_enum_addr_msw; |
| uint16_t tx_slave_port_offset; |
| uint16_t rx_slave_port_offset; |
| } __packed; |
| |
| struct afe_param_cdc_reg_cfg { |
| uint32_t minor_version; |
| uint32_t reg_logical_addr; |
| uint32_t reg_field_type; |
| uint32_t reg_field_bit_mask; |
| uint16_t reg_bit_width; |
| uint16_t reg_offset_scale; |
| } __packed; |
| |
| #define AFE_API_VERSION_CDC_REG_PAGE_CFG 1 |
| |
| enum { |
| AFE_CDC_REG_PAGE_ASSIGN_PROC_ID_0 = 0, |
| AFE_CDC_REG_PAGE_ASSIGN_PROC_ID_1, |
| AFE_CDC_REG_PAGE_ASSIGN_PROC_ID_2, |
| AFE_CDC_REG_PAGE_ASSIGN_PROC_ID_3, |
| }; |
| |
| struct afe_param_cdc_reg_page_cfg { |
| uint32_t minor_version; |
| uint32_t enable; |
| uint32_t proc_id; |
| } __packed; |
| |
| struct afe_param_cdc_reg_cfg_data { |
| uint32_t num_registers; |
| struct afe_param_cdc_reg_cfg *reg_data; |
| } __packed; |
| |
| struct afe_svc_cmd_set_param { |
| uint32_t payload_size; |
| uint32_t payload_address_lsw; |
| uint32_t payload_address_msw; |
| uint32_t mem_map_handle; |
| } __packed; |
| |
| struct afe_svc_param_data { |
| uint32_t module_id; |
| uint32_t param_id; |
| uint16_t param_size; |
| uint16_t reserved; |
| } __packed; |
| |
| struct afe_param_hw_mad_ctrl { |
| uint32_t minor_version; |
| uint16_t mad_type; |
| uint16_t mad_enable; |
| } __packed; |
| |
| struct afe_cmd_hw_mad_ctrl { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_param_hw_mad_ctrl payload; |
| } __packed; |
| |
| struct afe_cmd_hw_mad_slimbus_slave_port_cfg { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_param_slimbus_slave_port_cfg sb_port_cfg; |
| } __packed; |
| |
| struct afe_cmd_sw_mad_enable { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| } __packed; |
| |
| struct afe_param_cdc_reg_cfg_payload { |
| struct afe_svc_param_data common; |
| struct afe_param_cdc_reg_cfg reg_cfg; |
| } __packed; |
| |
| struct afe_lpass_clk_config_command_v2 { |
| struct apr_hdr hdr; |
| struct afe_svc_cmd_set_param param; |
| struct afe_svc_param_data pdata; |
| struct afe_clk_set clk_cfg; |
| } __packed; |
| |
| /* |
| * reg_data's size can be up to AFE_MAX_CDC_REGISTERS_TO_CONFIG |
| */ |
| struct afe_svc_cmd_cdc_reg_cfg { |
| struct apr_hdr hdr; |
| struct afe_svc_cmd_set_param param; |
| struct afe_param_cdc_reg_cfg_payload reg_data[0]; |
| } __packed; |
| |
| struct afe_svc_cmd_init_cdc_reg_cfg { |
| struct apr_hdr hdr; |
| struct afe_svc_cmd_set_param param; |
| struct afe_port_param_data_v2 init; |
| } __packed; |
| |
| struct afe_svc_cmd_sb_slave_cfg { |
| struct apr_hdr hdr; |
| struct afe_svc_cmd_set_param param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_param_cdc_slimbus_slave_cfg sb_slave_cfg; |
| } __packed; |
| |
| struct afe_svc_cmd_cdc_reg_page_cfg { |
| struct apr_hdr hdr; |
| struct afe_svc_cmd_set_param param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_param_cdc_reg_page_cfg cdc_reg_page_cfg; |
| } __packed; |
| |
| struct afe_svc_cmd_cdc_aanc_version { |
| struct apr_hdr hdr; |
| struct afe_svc_cmd_set_param param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_param_id_cdc_aanc_version version; |
| } __packed; |
| |
| struct afe_port_cmd_set_aanc_param { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| struct afe_port_param_data_v2 pdata; |
| union { |
| struct afe_param_aanc_port_cfg aanc_port_cfg; |
| struct afe_mod_enable_param mod_enable; |
| } __packed data; |
| } __packed; |
| |
| struct afe_port_cmd_set_aanc_acdb_table { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_set_param_v2 param; |
| } __packed; |
| |
| /* Dolby DAP topology */ |
| #define DOLBY_ADM_COPP_TOPOLOGY_ID 0x0001033B |
| #define DS2_ADM_COPP_TOPOLOGY_ID 0x1301033B |
| |
| /* RMS value from DSP */ |
| #define RMS_MODULEID_APPI_PASSTHRU 0x10009011 |
| #define RMS_PARAM_FIRST_SAMPLE 0x10009012 |
| #define RMS_PAYLOAD_LEN 4 |
| |
| /* Customized mixing in matix mixer */ |
| #define MTMX_MODULE_ID_DEFAULT_CHMIXER 0x00010341 |
| #define DEFAULT_CHMIXER_PARAM_ID_COEFF 0x00010342 |
| #define CUSTOM_STEREO_PAYLOAD_SIZE 9 |
| #define CUSTOM_STEREO_CMD_PARAM_SIZE 24 |
| #define CUSTOM_STEREO_NUM_OUT_CH 0x0002 |
| #define CUSTOM_STEREO_NUM_IN_CH 0x0002 |
| #define CUSTOM_STEREO_INDEX_PARAM 0x0002 |
| #define Q14_GAIN_ZERO_POINT_FIVE 0x2000 |
| #define Q14_GAIN_UNITY 0x4000 |
| |
| struct afe_svc_cmd_set_clip_bank_selection { |
| struct apr_hdr hdr; |
| struct afe_svc_cmd_set_param param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_param_id_clip_bank_sel bank_sel; |
| } __packed; |
| |
| /* Ultrasound supported formats */ |
| #define US_POINT_EPOS_FORMAT_V2 0x0001272D |
| #define US_RAW_FORMAT_V2 0x0001272C |
| #define US_PROX_FORMAT_V4 0x0001273B |
| #define US_RAW_SYNC_FORMAT 0x0001272F |
| #define US_GES_SYNC_FORMAT 0x00012730 |
| |
| #define AFE_MODULE_GROUP_DEVICE 0x00010254 |
| #define AFE_PARAM_ID_GROUP_DEVICE_CFG 0x00010255 |
| #define AFE_PARAM_ID_GROUP_DEVICE_ENABLE 0x00010256 |
| #define AFE_GROUP_DEVICE_ID_SECONDARY_MI2S_RX 0x1102 |
| |
| /* Payload of the #AFE_PARAM_ID_GROUP_DEVICE_CFG |
| * parameter, which configures max of 8 AFE ports |
| * into a group. |
| * The fixed size of this structure is sixteen bytes. |
| */ |
| struct afe_group_device_group_cfg { |
| u32 minor_version; |
| u16 group_id; |
| u16 num_channels; |
| u16 port_id[8]; |
| } __packed; |
| |
| #define AFE_GROUP_DEVICE_ID_PRIMARY_TDM_RX \ |
| (AFE_PORT_ID_PRIMARY_TDM_RX + 0x100) |
| #define AFE_GROUP_DEVICE_ID_PRIMARY_TDM_TX \ |
| (AFE_PORT_ID_PRIMARY_TDM_TX + 0x100) |
| #define AFE_GROUP_DEVICE_ID_SECONDARY_TDM_RX \ |
| (AFE_PORT_ID_SECONDARY_TDM_RX + 0x100) |
| #define AFE_GROUP_DEVICE_ID_SECONDARY_TDM_TX \ |
| (AFE_PORT_ID_SECONDARY_TDM_TX + 0x100) |
| #define AFE_GROUP_DEVICE_ID_TERTIARY_TDM_RX \ |
| (AFE_PORT_ID_TERTIARY_TDM_RX + 0x100) |
| #define AFE_GROUP_DEVICE_ID_TERTIARY_TDM_TX \ |
| (AFE_PORT_ID_TERTIARY_TDM_TX + 0x100) |
| #define AFE_GROUP_DEVICE_ID_QUATERNARY_TDM_RX \ |
| (AFE_PORT_ID_QUATERNARY_TDM_RX + 0x100) |
| #define AFE_GROUP_DEVICE_ID_QUATERNARY_TDM_TX \ |
| (AFE_PORT_ID_QUATERNARY_TDM_TX + 0x100) |
| #define AFE_GROUP_DEVICE_ID_QUINARY_TDM_RX \ |
| (AFE_PORT_ID_QUINARY_TDM_RX + 0x100) |
| #define AFE_GROUP_DEVICE_ID_QUINARY_TDM_TX \ |
| (AFE_PORT_ID_QUINARY_TDM_TX + 0x100) |
| |
| /* ID of the parameter used by #AFE_MODULE_GROUP_DEVICE to configure the |
| * group device. #AFE_SVC_CMD_SET_PARAM can use this parameter ID. |
| * |
| * Requirements: |
| * - Configure the group before the member ports in the group are |
| * configured and started. |
| * - Enable the group only after it is configured. |
| * - Stop all member ports in the group before disabling the group. |
| */ |
| #define AFE_PARAM_ID_GROUP_DEVICE_TDM_CONFIG 0x0001029E |
| |
| /* Version information used to handle future additions to |
| * AFE_PARAM_ID_GROUP_DEVICE_TDM_CONFIG processing (for backward compatibility). |
| */ |
| #define AFE_API_VERSION_GROUP_DEVICE_TDM_CONFIG 0x1 |
| |
| /* Number of AFE ports in group device */ |
| #define AFE_GROUP_DEVICE_NUM_PORTS 8 |
| |
| /* Payload of the AFE_PARAM_ID_GROUP_DEVICE_TDM_CONFIG parameter ID |
| * used by AFE_MODULE_GROUP_DEVICE. |
| */ |
| struct afe_param_id_group_device_tdm_cfg { |
| u32 group_device_cfg_minor_version; |
| /* Minor version used to track group device configuration. |
| * @values #AFE_API_VERSION_GROUP_DEVICE_TDM_CONFIG |
| */ |
| |
| u16 group_id; |
| /* ID for the group device. |
| * @values |
| * - #AFE_GROUP_DEVICE_ID_PRIMARY_TDM_RX |
| * - #AFE_GROUP_DEVICE_ID_PRIMARY_TDM_TX |
| * - #AFE_GROUP_DEVICE_ID_SECONDARY_TDM_RX |
| * - #AFE_GROUP_DEVICE_ID_SECONDARY_TDM_TX |
| * - #AFE_GROUP_DEVICE_ID_TERTIARY_TDM_RX |
| * - #AFE_GROUP_DEVICE_ID_TERTIARY_TDM_TX |
| * - #AFE_GROUP_DEVICE_ID_QUATERNARY_TDM_RX |
| * - #AFE_GROUP_DEVICE_ID_QUATERNARY_TDM_TX |
| */ |
| |
| u16 reserved; |
| /* 0 */ |
| |
| u16 port_id[AFE_GROUP_DEVICE_NUM_PORTS]; |
| /* Array of member port IDs of this group. |
| * @values |
| * - #AFE_PORT_ID_PRIMARY_TDM_RX |
| * - #AFE_PORT_ID_PRIMARY_TDM_RX_1 |
| * - #AFE_PORT_ID_PRIMARY_TDM_RX_2 |
| * - #AFE_PORT_ID_PRIMARY_TDM_RX_3 |
| * - #AFE_PORT_ID_PRIMARY_TDM_RX_4 |
| * - #AFE_PORT_ID_PRIMARY_TDM_RX_5 |
| * - #AFE_PORT_ID_PRIMARY_TDM_RX_6 |
| * - #AFE_PORT_ID_PRIMARY_TDM_RX_7 |
| |
| * - #AFE_PORT_ID_PRIMARY_TDM_TX |
| * - #AFE_PORT_ID_PRIMARY_TDM_TX_1 |
| * - #AFE_PORT_ID_PRIMARY_TDM_TX_2 |
| * - #AFE_PORT_ID_PRIMARY_TDM_TX_3 |
| * - #AFE_PORT_ID_PRIMARY_TDM_TX_4 |
| * - #AFE_PORT_ID_PRIMARY_TDM_TX_5 |
| * - #AFE_PORT_ID_PRIMARY_TDM_TX_6 |
| * - #AFE_PORT_ID_PRIMARY_TDM_TX_7 |
| |
| * - #AFE_PORT_ID_SECONDARY_TDM_RX |
| * - #AFE_PORT_ID_SECONDARY_TDM_RX_1 |
| * - #AFE_PORT_ID_SECONDARY_TDM_RX_2 |
| * - #AFE_PORT_ID_SECONDARY_TDM_RX_3 |
| * - #AFE_PORT_ID_SECONDARY_TDM_RX_4 |
| * - #AFE_PORT_ID_SECONDARY_TDM_RX_5 |
| * - #AFE_PORT_ID_SECONDARY_TDM_RX_6 |
| * - #AFE_PORT_ID_SECONDARY_TDM_RX_7 |
| |
| * - #AFE_PORT_ID_SECONDARY_TDM_TX |
| * - #AFE_PORT_ID_SECONDARY_TDM_TX_1 |
| * - #AFE_PORT_ID_SECONDARY_TDM_TX_2 |
| * - #AFE_PORT_ID_SECONDARY_TDM_TX_3 |
| * - #AFE_PORT_ID_SECONDARY_TDM_TX_4 |
| * - #AFE_PORT_ID_SECONDARY_TDM_TX_5 |
| * - #AFE_PORT_ID_SECONDARY_TDM_TX_6 |
| * - #AFE_PORT_ID_SECONDARY_TDM_TX_7 |
| |
| * - #AFE_PORT_ID_TERTIARY_TDM_RX |
| * - #AFE_PORT_ID_TERTIARY_TDM_RX_1 |
| * - #AFE_PORT_ID_TERTIARY_TDM_RX_2 |
| * - #AFE_PORT_ID_TERTIARY_TDM_RX_3 |
| * - #AFE_PORT_ID_TERTIARY_TDM_RX_4 |
| * - #AFE_PORT_ID_TERTIARY_TDM_RX_5 |
| * - #AFE_PORT_ID_TERTIARY_TDM_RX_6 |
| * - #AFE_PORT_ID_TERTIARY_TDM_RX_7 |
| |
| * - #AFE_PORT_ID_TERTIARY_TDM_TX |
| * - #AFE_PORT_ID_TERTIARY_TDM_TX_1 |
| * - #AFE_PORT_ID_TERTIARY_TDM_TX_2 |
| * - #AFE_PORT_ID_TERTIARY_TDM_TX_3 |
| * - #AFE_PORT_ID_TERTIARY_TDM_TX_4 |
| * - #AFE_PORT_ID_TERTIARY_TDM_TX_5 |
| * - #AFE_PORT_ID_TERTIARY_TDM_TX_6 |
| * - #AFE_PORT_ID_TERTIARY_TDM_TX_7 |
| |
| * - #AFE_PORT_ID_QUATERNARY_TDM_RX |
| * - #AFE_PORT_ID_QUATERNARY_TDM_RX_1 |
| * - #AFE_PORT_ID_QUATERNARY_TDM_RX_2 |
| * - #AFE_PORT_ID_QUATERNARY_TDM_RX_3 |
| * - #AFE_PORT_ID_QUATERNARY_TDM_RX_4 |
| * - #AFE_PORT_ID_QUATERNARY_TDM_RX_5 |
| * - #AFE_PORT_ID_QUATERNARY_TDM_RX_6 |
| * - #AFE_PORT_ID_QUATERNARY_TDM_RX_7 |
| |
| * - #AFE_PORT_ID_QUATERNARY_TDM_TX |
| * - #AFE_PORT_ID_QUATERNARY_TDM_TX_1 |
| * - #AFE_PORT_ID_QUATERNARY_TDM_TX_2 |
| * - #AFE_PORT_ID_QUATERNARY_TDM_TX_3 |
| * - #AFE_PORT_ID_QUATERNARY_TDM_TX_4 |
| * - #AFE_PORT_ID_QUATERNARY_TDM_TX_5 |
| * - #AFE_PORT_ID_QUATERNARY_TDM_TX_6 |
| * - #AFE_PORT_ID_QUATERNARY_TDM_TX_7 |
| * @tablebulletend |
| */ |
| |
| u32 num_channels; |
| /* Number of enabled slots for TDM frame. |
| * @values 1 to 8 |
| */ |
| |
| u32 sample_rate; |
| /* Sampling rate of the port. |
| * @values |
| * - #AFE_PORT_SAMPLE_RATE_8K |
| * - #AFE_PORT_SAMPLE_RATE_16K |
| * - #AFE_PORT_SAMPLE_RATE_24K |
| * - #AFE_PORT_SAMPLE_RATE_32K |
| * - #AFE_PORT_SAMPLE_RATE_48K @tablebulletend |
| */ |
| |
| u32 bit_width; |
| /* Bit width of the sample. |
| * @values 16, 24, (32) |
| */ |
| |
| u16 nslots_per_frame; |
| /* Number of slots per frame. Typical : 1, 2, 4, 8, 16, 32. |
| * @values 1 - 32 |
| */ |
| |
| u16 slot_width; |
| /* Slot width of the slot in a TDM frame. (slot_width >= bit_width) |
| * have to be satisfied. |
| * @values 16, 24, 32 |
| */ |
| |
| u32 slot_mask; |
| /* Position of active slots. When that bit is set, that paricular |
| * slot is active. |
| * Number of active slots can be inferred by number of bits set in |
| * the mask. Only 8 individual bits can be enabled. |
| * Bits 0..31 corresponding to slot 0..31 |
| * @values 1 to 2^32 -1 |
| */ |
| } __packed; |
| |
| /* Payload of the #AFE_PARAM_ID_GROUP_DEVICE_ENABLE |
| * parameter, which enables or |
| * disables any module. |
| * The fixed size of this structure is four bytes. |
| */ |
| |
| struct afe_group_device_enable { |
| u16 group_id; |
| /* valid value is AFE_GROUP_DEVICE_ID_SECONDARY_MI2S_RX */ |
| u16 enable; |
| /* Enables (1) or disables (0) the module. */ |
| } __packed; |
| |
| union afe_port_group_config { |
| struct afe_group_device_group_cfg group_cfg; |
| struct afe_group_device_enable group_enable; |
| struct afe_param_id_group_device_tdm_cfg tdm_cfg; |
| } __packed; |
| |
| struct afe_port_group_create { |
| struct apr_hdr hdr; |
| struct afe_svc_cmd_set_param param; |
| struct afe_port_param_data_v2 pdata; |
| union afe_port_group_config data; |
| } __packed; |
| |
| /* ID of the parameter used by #AFE_MODULE_AUDIO_DEV_INTERFACE to specify |
| * the timing statistics of the corresponding device interface. |
| * Client can periodically query for the device time statistics to help adjust |
| * the PLL based on the drift value. The get param command must be sent to |
| * AFE port ID corresponding to device interface |
| |
| * This parameter ID supports following get param commands: |
| * #AFE_PORT_CMD_GET_PARAM_V2 and |
| * #AFE_PORT_CMD_GET_PARAM_V3. |
| */ |
| #define AFE_PARAM_ID_DEV_TIMING_STATS 0x000102AD |
| |
| /* Version information used to handle future additions to AFE device |
| * interface timing statistics (for backward compatibility). |
| */ |
| #define AFE_API_VERSION_DEV_TIMING_STATS 0x1 |
| |
| /* Enumeration for specifying a sink(Rx) device */ |
| #define AFE_SINK_DEVICE 0x0 |
| |
| /* Enumeration for specifying a source(Tx) device */ |
| #define AFE_SOURCE_DEVICE 0x1 |
| |
| /* Enumeration for specifying the drift reference is of type AV Timer */ |
| #define AFE_REF_TIMER_TYPE_AVTIMER 0x0 |
| |
| /* Message payload structure for the |
| * AFE_PARAM_ID_DEV_TIMING_STATS parameter. |
| */ |
| struct afe_param_id_dev_timing_stats { |
| /* Minor version used to track the version of device interface timing |
| * statistics. Currently, the supported version is 1. |
| * @values #AFE_API_VERSION_DEV_TIMING_STATS |
| */ |
| u32 minor_version; |
| |
| /* Indicates the device interface direction as either |
| * source (Tx) or sink (Rx). |
| * @values |
| * #AFE_SINK_DEVICE |
| * #AFE_SOURCE_DEVICE |
| */ |
| u16 device_direction; |
| |
| /* Reference timer for drift accumulation and time stamp information. |
| * @values |
| * #AFE_REF_TIMER_TYPE_AVTIMER @tablebulletend |
| */ |
| u16 reference_timer; |
| |
| /* |
| * Flag to indicate if resync is required on the client side for |
| * drift correction. Flag is set to TRUE for the first get_param |
| * response after device interface starts. This flag value can be |
| * used by client to identify if device interface restart has |
| * happened and if any re-sync is required at their end for drift |
| * correction. |
| * @values |
| * 0: FALSE (Resync not required) |
| * 1: TRUE (Resync required) @tablebulletend |
| */ |
| u32 resync_flag; |
| |
| /* Accumulated drift value in microseconds. This value is updated |
| * every 100th ms. |
| * Positive drift value indicates AV timer is running faster than device |
| * Negative drift value indicates AV timer is running slower than device |
| * @values Any valid int32 number |
| */ |
| s32 acc_drift_value; |
| |
| /* Lower 32 bits of the 64-bit absolute timestamp of reference |
| * timer in microseconds. |
| |
| * This timestamp corresponds to the time when the drift values |
| * are accumlated for every 100th ms. |
| * @values Any valid uint32 number |
| */ |
| u32 ref_timer_abs_ts_lsw; |
| |
| /* Upper 32 bits of the 64-bit absolute timestamp of reference |
| * timer in microseconds. |
| * This timestamp corresponds to the time when the drift values |
| * are accumlated for every 100th ms. |
| * @values Any valid uint32 number |
| */ |
| u32 ref_timer_abs_ts_msw; |
| } __packed; |
| |
| struct afe_av_dev_drift_get_param { |
| struct apr_hdr hdr; |
| struct afe_port_cmd_get_param_v2 get_param; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_param_id_dev_timing_stats timing_stats; |
| } __packed; |
| |
| struct afe_av_dev_drift_get_param_resp { |
| uint32_t status; |
| struct afe_port_param_data_v2 pdata; |
| struct afe_param_id_dev_timing_stats timing_stats; |
| } __packed; |
| |
| /* Command for Matrix or Stream Router */ |
| #define ASM_SESSION_CMD_SET_MTMX_STRTR_PARAMS_V2 0x00010DCE |
| /* Module for AVSYNC */ |
| #define ASM_SESSION_MTMX_STRTR_MODULE_ID_AVSYNC 0x00010DC6 |
| |
| /* Parameter used by #ASM_SESSION_MTMX_STRTR_MODULE_ID_AVSYNC to specify the |
| * render window start value. This parameter is supported only for a Set |
| * command (not a Get command) in the Rx direction |
| * (#ASM_SESSION_CMD_SET_MTMX_STRTR_PARAMS_V2). |
| * Render window start is a value (session time minus timestamp, or ST-TS) |
| * below which frames are held, and after which frames are immediately |
| * rendered. |
| */ |
| #define ASM_SESSION_MTMX_STRTR_PARAM_RENDER_WINDOW_START_V2 0x00010DD1 |
| |
| /* Parameter used by #ASM_SESSION_MTMX_STRTR_MODULE_ID_AVSYNC to specify the |
| * render window end value. This parameter is supported only for a Set |
| * command (not a Get command) in the Rx direction |
| * (#ASM_SESSION_CMD_SET_MTMX_STRTR_PARAMS_V2). Render window end is a value |
| * (session time minus timestamp) above which frames are dropped, and below |
| * which frames are immediately rendered. |
| */ |
| #define ASM_SESSION_MTMX_STRTR_PARAM_RENDER_WINDOW_END_V2 0x00010DD2 |
| |
| /* Generic payload of the window parameters in the |
| * #ASM_SESSION_MTMX_STRTR_MODULE_ID_AVSYNC module. |
| * This payload is supported only for a Set command |
| * (not a Get command) on the Rx path. |
| */ |
| struct asm_session_mtmx_strtr_param_window_v2_t { |
| u32 window_lsw; |
| /* Lower 32 bits of the render window start value. */ |
| |
| u32 window_msw; |
| /* Upper 32 bits of the render window start value. |
| * |
| * The 64-bit number formed by window_lsw and window_msw specifies a |
| * signed 64-bit window value in microseconds. The sign extension is |
| * necessary. This value is used by the following parameter IDs: |
| * #ASM_SESSION_MTMX_STRTR_PARAM_RENDER_WINDOW_START_V2 |
| * #ASM_SESSION_MTMX_STRTR_PARAM_RENDER_WINDOW_END_V2 |
| * #ASM_SESSION_MTMX_STRTR_PARAM_STAT_WINDOW_START_V2 |
| * #ASM_SESSION_MTMX_STRTR_PARAM_STAT_WINDOW_END_V2 |
| * The value depends on which parameter ID is used. |
| * The aDSP honors the windows at a granularity of 1 ms. |
| */ |
| }; |
| |
| struct asm_session_cmd_set_mtmx_strstr_params_v2 { |
| uint32_t data_payload_addr_lsw; |
| /* Lower 32 bits of the 64-bit data payload address. */ |
| |
| uint32_t data_payload_addr_msw; |
| /* Upper 32 bits of the 64-bit data payload address. |
| * If the address is not sent (NULL), the message is in the payload. |
| * If the address is sent (non-NULL), the parameter data payloads |
| * begin at the specified address. |
| */ |
| |
| uint32_t mem_map_handle; |
| /* Unique identifier for an address. This memory map handle is returned |
| * by the aDSP through the #ASM_CMD_SHARED_MEM_MAP_REGIONS command. |
| * values |
| * - NULL -- Parameter data payloads are within the message payload |
| * (in-band). |
| * - Non-NULL -- Parameter data payloads begin at the address specified |
| * in the data_payload_addr_lsw and data_payload_addr_msw fields |
| * (out-of-band). |
| */ |
| |
| uint32_t data_payload_size; |
| /* Actual size of the variable payload accompanying the message, or in |
| * shared memory. This field is used for parsing the parameter payload. |
| * values > 0 bytes |
| */ |
| |
| uint32_t direction; |
| /* Direction of the entity (matrix mixer or stream router) on which |
| * the parameter is to be set. |
| * values |
| * - 0 -- Rx (for Rx stream router or Rx matrix mixer) |
| * - 1 -- Tx (for Tx stream router or Tx matrix mixer) |
| */ |
| }; |
| |
| /* Parameter used by #ASM_SESSION_MTMX_STRTR_MODULE_ID_AVSYNC which allows the |
| * audio client choose the rendering decision that the audio DSP should use. |
| */ |
| #define ASM_SESSION_MTMX_STRTR_PARAM_RENDER_MODE_CMD 0x00012F0D |
| |
| /* Indicates that rendering decision will be based on default rate |
| * (session clock based rendering, device driven). |
| * 1. The default session clock based rendering is inherently driven |
| * by the timing of the device. |
| * 2. After the initial decision is made (first buffer after a run |
| * command), subsequent data rendering decisions are made with |
| * respect to the rate at which the device is rendering, thus deriving |
| * its timing from the device. |
| * 3. While this decision making is simple, it has some inherent limitations |
| * (mentioned in the next section). |
| * 4. If this API is not set, the session clock based rendering will be assumed |
| * and this will ensure that the DSP is backward compatible. |
| */ |
| #define ASM_SESSION_MTMX_STRTR_PARAM_RENDER_DEFAULT 0 |
| |
| /* Indicates that rendering decision will be based on local clock rate. |
| * 1. In the DSP loopback/client loopback use cases (frame based |
| * inputs), the incoming data into audio DSP is time-stamped at the |
| * local clock rate (STC). |
| * 2. This TS rate may match the incoming data rate or maybe different |
| * from the incoming data rate. |
| * 3. Regardless, the data will be time-stamped with local STC and |
| * therefore, the client is recommended to set this mode for these |
| * use cases. This method is inherently more robust to sequencing |
| * (AFE Start/Stop) and device switches, among other benefits. |
| * 4. This API will inform the DSP to compare every incoming buffer TS |
| * against local STC. |
| * 5. DSP will continue to honor render windows APIs, as before. |
| */ |
| #define ASM_SESSION_MTMX_STRTR_PARAM_RENDER_LOCAL_STC 1 |
| |
| /* Structure for rendering decision parameter */ |
| struct asm_session_mtmx_strtr_param_render_mode_t { |
| /* Specifies the type of rendering decision the audio DSP should use. |
| * |
| * @values |
| * - #ASM_SESSION_MTMX_STRTR_PARAM_RENDER_DEFAULT |
| * - #ASM_SESSION_MTMX_STRTR_PARAM_RENDER_LOCAL_STC |
| */ |
| u32 flags; |
| } __packed; |
| |
| /* Parameter used by #ASM_SESSION_MTMX_STRTR_MODULE_ID_AVSYNC which allows the |
| * audio client to specify the clock recovery mechanism that the audio DSP |
| * should use. |
| */ |
| |
| #define ASM_SESSION_MTMX_STRTR_PARAM_CLK_REC_CMD 0x00012F0E |
| |
| /* Indicates that default clock recovery will be used (no clock recovery). |
| * If the client wishes that no clock recovery be done, the client can |
| * choose this. This means that no attempt will made by the DSP to try and |
| * match the rates of the input and output audio. |
| */ |
| #define ASM_SESSION_MTMX_STRTR_PARAM_CLK_REC_NONE 0 |
| |
| /* Indicates that independent clock recovery needs to be used. |
| * 1. In the DSP loopback/client loopback use cases (frame based inputs), |
| * the client should choose the independent clock recovery option. |
| * 2. This basically de-couples the audio and video from knowing each others |
| * clock sources and lets the audio DSP independently rate match the input |
| * and output rates. |
| * 3. After drift detection, the drift correction is achieved by either pulling |
| * the PLLs (if applicable) or by stream to device rate matching |
| * (for PCM use cases) by comparing drift with respect to STC. |
| * 4. For passthrough use cases, since the PLL pulling is the only option, |
| * a best effort will be made. |
| * If PLL pulling is not possible / available, the rendering will be |
| * done without rate matching. |
| */ |
| #define ASM_SESSION_MTMX_STRTR_PARAM_CLK_REC_AUTO 1 |
| |
| /* Payload of the #ASM_SESSION_MTMX_STRTR_PARAM_CLK_REC parameter. |
| */ |
| struct asm_session_mtmx_strtr_param_clk_rec_t { |
| /* Specifies the type of clock recovery that the audio DSP should |
| * use for rate matching. |
| */ |
| |
| /* @values |
| * #ASM_SESSION_MTMX_STRTR_PARAM_CLK_REC_DEFAULT |
| * #ASM_SESSION_MTMX_STRTR_PARAM_CLK_REC_INDEPENDENT |
| */ |
| u32 flags; |
| } __packed; |
| |
| |
| /* Parameter used by #ASM_SESSION_MTMX_STRTR_MODULE_ID_AVSYNC to |
| * realize smoother adjustment of audio session clock for a specified session. |
| * The desired audio session clock adjustment(in micro seconds) is specified |
| * using the command #ASM_SESSION_CMD_ADJUST_SESSION_CLOCK_V2. |
| * Delaying/Advancing the session clock would be implemented by inserting |
| * interpolated/dropping audio samples in the playback path respectively. |
| * Also, this parameter has to be configured before the Audio Session is put |
| * to RUN state to avoid cold start latency/glitches in the playback. |
| */ |
| |
| #define ASM_SESSION_MTMX_PARAM_ADJUST_SESSION_TIME_CTL 0x00013217 |
| |
| struct asm_session_mtmx_param_adjust_session_time_ctl_t { |
| /* Specifies whether the module is enabled or not |
| * @values |
| * 0 -- disabled |
| * 1 -- enabled |
| */ |
| u32 enable; |
| }; |
| |
| union asm_session_mtmx_strtr_param_config { |
| struct asm_session_mtmx_strtr_param_window_v2_t window_param; |
| struct asm_session_mtmx_strtr_param_render_mode_t render_param; |
| struct asm_session_mtmx_strtr_param_clk_rec_t clk_rec_param; |
| struct asm_session_mtmx_param_adjust_session_time_ctl_t adj_time_param; |
| } __packed; |
| |
| struct asm_mtmx_strtr_params { |
| struct apr_hdr hdr; |
| struct asm_session_cmd_set_mtmx_strstr_params_v2 param; |
| struct asm_stream_param_data_v2 data; |
| union asm_session_mtmx_strtr_param_config config; |
| } __packed; |
| |
| #define ASM_SESSION_CMD_GET_MTMX_STRTR_PARAMS_V2 0x00010DCF |
| #define ASM_SESSION_CMDRSP_GET_MTMX_STRTR_PARAMS_V2 0x00010DD0 |
| |
| #define ASM_SESSION_MTMX_STRTR_PARAM_SESSION_TIME_V3 0x00012F0B |
| #define ASM_SESSION_MTMX_STRTR_PARAM_STIME_TSTMP_FLG_BMASK (0x80000000UL) |
| |
| struct asm_session_cmd_get_mtmx_strstr_params_v2 { |
| uint32_t data_payload_addr_lsw; |
| /* Lower 32 bits of the 64-bit data payload address. */ |
| |
| uint32_t data_payload_addr_msw; |
| /* |
| * Upper 32 bits of the 64-bit data payload address. |
| * If the address is not sent (NULL), the message is in the payload. |
| * If the address is sent (non-NULL), the parameter data payloads |
| * begin at the specified address. |
| */ |
| |
| uint32_t mem_map_handle; |
| /* |
| * Unique identifier for an address. This memory map handle is returned |
| * by the aDSP through the #ASM_CMD_SHARED_MEM_MAP_REGIONS command. |
| * values |
| * - NULL -- Parameter data payloads are within the message payload |
| * (in-band). |
| * - Non-NULL -- Parameter data payloads begin at the address specified |
| * in the data_payload_addr_lsw and data_payload_addr_msw fields |
| * (out-of-band). |
| */ |
| uint32_t direction; |
| /* |
| * Direction of the entity (matrix mixer or stream router) on which |
| * the parameter is to be set. |
| * values |
| * - 0 -- Rx (for Rx stream router or Rx matrix mixer) |
| * - 1 -- Tx (for Tx stream router or Tx matrix mixer) |
| */ |
| uint32_t module_id; |
| /* Unique module ID. */ |
| |
| uint32_t param_id; |
| /* Unique parameter ID. */ |
| |
| uint32_t param_max_size; |
| }; |
| |
| struct asm_session_mtmx_strtr_param_session_time_v3_t { |
| uint32_t session_time_lsw; |
| /* Lower 32 bits of the current session time in microseconds */ |
| |
| uint32_t session_time_msw; |
| /* |
| * Upper 32 bits of the current session time in microseconds. |
| * The 64-bit number formed by session_time_lsw and session_time_msw |
| * is treated as signed. |
| */ |
| |
| uint32_t absolute_time_lsw; |
| /* |
| * Lower 32 bits of the 64-bit absolute time in microseconds. |
| * This is the time when the sample corresponding to the |
| * session_time_lsw is rendered to the hardware. This absolute |
| * time can be slightly in the future or past. |
| */ |
| |
| uint32_t absolute_time_msw; |
| /* |
| * Upper 32 bits of the 64-bit absolute time in microseconds. |
| * This is the time when the sample corresponding to the |
| * session_time_msw is rendered to hardware. This absolute |
| * time can be slightly in the future or past. The 64-bit number |
| * formed by absolute_time_lsw and absolute_time_msw is treated as |
| * unsigned. |
| */ |
| |
| uint32_t time_stamp_lsw; |
| /* Lower 32 bits of the last processed timestamp in microseconds */ |
| |
| uint32_t time_stamp_msw; |
| /* |
| * Upper 32 bits of the last processed timestamp in microseconds. |
| * The 64-bit number formed by time_stamp_lsw and time_stamp_lsw |
| * is treated as unsigned. |
| */ |
| |
| uint32_t flags; |
| /* |
| * Keeps track of any additional flags needed. |
| * @values{for bit 31} |
| * - 0 -- Uninitialized/invalid |
| * - 1 -- Valid |
| * All other bits are reserved; clients must set them to zero. |
| */ |
| }; |
| |
| union asm_session_mtmx_strtr_data_type { |
| struct asm_session_mtmx_strtr_param_session_time_v3_t session_time; |
| }; |
| |
| struct asm_mtmx_strtr_get_params { |
| struct apr_hdr hdr; |
| struct asm_session_cmd_get_mtmx_strstr_params_v2 param_info; |
| } __packed; |
| |
| struct asm_mtmx_strtr_get_params_cmdrsp { |
| uint32_t err_code; |
| struct asm_stream_param_data_v2 param_info; |
| union asm_session_mtmx_strtr_data_type param_data; |
| } __packed; |
| |
| #define AUDPROC_MODULE_ID_RESAMPLER 0x00010719 |
| |
| enum { |
| LEGACY_PCM = 0, |
| COMPRESSED_PASSTHROUGH, |
| COMPRESSED_PASSTHROUGH_CONVERT, |
| COMPRESSED_PASSTHROUGH_DSD, |
| LISTEN, |
| COMPRESSED_PASSTHROUGH_GEN, |
| COMPRESSED_PASSTHROUGH_IEC61937 |
| }; |
| |
| #define AUDPROC_MODULE_ID_COMPRESSED_MUTE 0x00010770 |
| #define AUDPROC_PARAM_ID_COMPRESSED_MUTE 0x00010771 |
| |
| struct adm_set_compressed_device_mute { |
| struct adm_cmd_set_pp_params_v5 command; |
| struct adm_param_data_v5 params; |
| u32 mute_on; |
| } __packed; |
| |
| #define AUDPROC_MODULE_ID_COMPRESSED_LATENCY 0x0001076E |
| #define AUDPROC_PARAM_ID_COMPRESSED_LATENCY 0x0001076F |
| |
| struct adm_set_compressed_device_latency { |
| struct adm_cmd_set_pp_params_v5 command; |
| struct adm_param_data_v5 params; |
| u32 latency; |
| } __packed; |
| |
| #define VOICEPROC_MODULE_ID_GENERIC_TX 0x00010EF6 |
| #define VOICEPROC_PARAM_ID_FLUENCE_SOUNDFOCUS 0x00010E37 |
| #define VOICEPROC_PARAM_ID_FLUENCE_SOURCETRACKING 0x00010E38 |
| #define MAX_SECTORS 8 |
| #define MAX_NOISE_SOURCE_INDICATORS 3 |
| #define MAX_POLAR_ACTIVITY_INDICATORS 360 |
| |
| struct sound_focus_param { |
| uint16_t start_angle[MAX_SECTORS]; |
| uint8_t enable[MAX_SECTORS]; |
| uint16_t gain_step; |
| } __packed; |
| |
| struct source_tracking_param { |
| uint8_t vad[MAX_SECTORS]; |
| uint16_t doa_speech; |
| uint16_t doa_noise[MAX_NOISE_SOURCE_INDICATORS]; |
| uint8_t polar_activity[MAX_POLAR_ACTIVITY_INDICATORS]; |
| } __packed; |
| |
| struct adm_param_fluence_soundfocus_t { |
| uint16_t start_angles[MAX_SECTORS]; |
| uint8_t enables[MAX_SECTORS]; |
| uint16_t gain_step; |
| uint16_t reserved; |
| } __packed; |
| |
| struct adm_set_fluence_soundfocus_param { |
| struct adm_cmd_set_pp_params_v5 params; |
| struct adm_param_data_v5 data; |
| struct adm_param_fluence_soundfocus_t soundfocus_data; |
| } __packed; |
| |
| struct adm_param_fluence_sourcetracking_t { |
| uint8_t vad[MAX_SECTORS]; |
| uint16_t doa_speech; |
| uint16_t doa_noise[MAX_NOISE_SOURCE_INDICATORS]; |
| uint8_t polar_activity[MAX_POLAR_ACTIVITY_INDICATORS]; |
| } __packed; |
| |
| #define AUDPROC_MODULE_ID_AUDIOSPHERE 0x00010916 |
| #define AUDPROC_PARAM_ID_AUDIOSPHERE_ENABLE 0x00010917 |
| #define AUDPROC_PARAM_ID_AUDIOSPHERE_STRENGTH 0x00010918 |
| #define AUDPROC_PARAM_ID_AUDIOSPHERE_CONFIG_MODE 0x00010919 |
| |
| #define AUDPROC_PARAM_ID_AUDIOSPHERE_COEFFS_STEREO_INPUT 0x0001091A |
| #define AUDPROC_PARAM_ID_AUDIOSPHERE_COEFFS_MULTICHANNEL_INPUT 0x0001091B |
| #define AUDPROC_PARAM_ID_AUDIOSPHERE_DESIGN_STEREO_INPUT 0x0001091C |
| #define AUDPROC_PARAM_ID_AUDIOSPHERE_DESIGN_MULTICHANNEL_INPUT 0x0001091D |
| |
| #define AUDPROC_PARAM_ID_AUDIOSPHERE_OPERATING_INPUT_MEDIA_INFO 0x0001091E |
| |
| #define AUDPROC_MODULE_ID_VOICE_TX_SECNS 0x10027059 |
| #define AUDPROC_PARAM_IDX_SEC_PRIMARY_MIC_CH 0x10014444 |
| |
| struct admx_sec_primary_mic_ch { |
| uint16_t version; |
| uint16_t reserved; |
| uint16_t sec_primary_mic_ch; |
| uint16_t reserved1; |
| } __packed; |
| |
| |
| struct adm_set_sec_primary_ch_params { |
| struct adm_cmd_set_pp_params_v5 params; |
| struct adm_param_data_v5 data; |
| struct admx_sec_primary_mic_ch sec_primary_mic_ch_data; |
| } __packed; |
| #endif /*_APR_AUDIO_V2_H_ */ |