Sheng Fang | d1d881e | 2013-03-20 12:04:17 +0800 | [diff] [blame^] | 1 | # This file allows user to override the factory |
| 2 | |
| 3 | # defaults for the WLAN Driver |
| 4 | |
| 5 | |
| 6 | # Enable IMPS or not |
| 7 | gEnableImps=1 |
| 8 | |
| 9 | # Enable/Disable Idle Scan |
| 10 | |
| 11 | gEnableIdleScan=0 |
| 12 | |
| 13 | |
| 14 | # Increase sleep duration (seconds) during IMPS |
| 15 | # 0 implies no periodic wake up from IMPS. Periodic wakeup is |
| 16 | # unnecessary if Idle Scan is disabled. |
| 17 | gImpsModSleepTime=0 |
| 18 | |
| 19 | |
| 20 | # Enable BMPS or not |
| 21 | gEnableBmps=1 |
| 22 | |
| 23 | # Enable suspend or not |
| 24 | |
| 25 | # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter |
| 26 | |
| 27 | gEnableSuspend=3 |
| 28 | |
| 29 | |
| 30 | # Phy Mode (auto, b, g, n, etc) |
| 31 | # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac |
| 32 | gDot11Mode=0 |
| 33 | |
| 34 | |
| 35 | # Handoff Enable(1) Disable(0) |
| 36 | |
| 37 | gEnableHandoff=0 |
| 38 | |
| 39 | |
| 40 | # CSR Roaming Enable(1) Disable(0) |
| 41 | |
| 42 | gRoamingTime=0 |
| 43 | |
| 44 | |
| 45 | # Assigned MAC Addresses - This will be used until NV items are in place |
| 46 | |
| 47 | # Each byte of MAC address is represented in Hex format as XX |
| 48 | |
| 49 | Intf0MacAddress=000AF58989FF |
| 50 | Intf1MacAddress=000AF58989FE |
| 51 | Intf2MacAddress=000AF58989FD |
| 52 | |
| 53 | Intf3MacAddress=000AF58989FC |
| 54 | |
| 55 | |
| 56 | # UAPSD service interval for VO,VI, BE, BK traffic |
| 57 | |
| 58 | InfraUapsdVoSrvIntv=0 |
| 59 | |
| 60 | InfraUapsdViSrvIntv=0 |
| 61 | |
| 62 | InfraUapsdBeSrvIntv=0 |
| 63 | |
| 64 | InfraUapsdBkSrvIntv=0 |
| 65 | |
| 66 | |
| 67 | # Disable RSSI FW filtering |
| 68 | |
| 69 | gEnableFWRssiMonitoring=1 |
| 70 | |
| 71 | |
| 72 | # Make 1x1 the default antenna configuration |
| 73 | |
| 74 | gNumRxAnt=1 |
| 75 | |
| 76 | |
| 77 | # Beacon filtering frequency (unit in beacon intervals) |
| 78 | |
| 79 | gNthBeaconFilter=50 |
| 80 | |
| 81 | |
| 82 | # Enable WAPI or not |
| 83 | |
| 84 | # WAPIIsEnabled=0 |
| 85 | |
| 86 | |
| 87 | # Flags to filter Mcast abd Bcast RX packets. |
| 88 | |
| 89 | # Value 0: No filtering, 1: Filter all Multicast. |
| 90 | |
| 91 | # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast |
| 92 | |
| 93 | McastBcastFilter=0 |
| 94 | |
| 95 | |
| 96 | #Flag to enable HostARPOffload feature or not |
| 97 | |
| 98 | hostArpOffload=0 |
| 99 | |
| 100 | |
| 101 | #SoftAP Related Parameters |
| 102 | |
| 103 | # AP MAc addr |
| 104 | |
| 105 | gAPMacAddr=000AF589dcab |
| 106 | |
| 107 | |
| 108 | # 802.11n Protection flag |
| 109 | |
| 110 | gEnableApProt=1 |
| 111 | |
| 112 | |
| 113 | #Enable OBSS protection |
| 114 | |
| 115 | gEnableApOBSSProt=0 |
| 116 | |
| 117 | |
| 118 | #Enable/Disable UAPSD for SoftAP |
| 119 | |
| 120 | gEnableApUapsd=0 |
| 121 | |
| 122 | |
| 123 | # Fixed Rate |
| 124 | |
| 125 | gFixedRate=0 |
| 126 | |
| 127 | |
| 128 | # Maximum Tx power |
| 129 | |
| 130 | # gTxPowerCap=30 |
| 131 | |
| 132 | |
| 133 | # Fragmentation Threshold |
| 134 | |
| 135 | # gFragmentationThreshold=2346 |
| 136 | |
| 137 | |
| 138 | # RTS threshold |
| 139 | |
| 140 | RTSThreshold=2347 |
| 141 | |
| 142 | |
| 143 | # Intra-BSS forward |
| 144 | |
| 145 | gDisableIntraBssFwd=0 |
| 146 | |
| 147 | |
| 148 | # WMM Enable/Disable |
| 149 | |
| 150 | WmmIsEnabled=0 |
| 151 | |
| 152 | |
| 153 | # 802.11d support |
| 154 | |
| 155 | g11dSupportEnabled=1 |
| 156 | |
| 157 | # CCX Support and fast transition |
| 158 | CcxEnabled=0 |
| 159 | FastTransitionEnabled=1 |
| 160 | ImplicitQosIsEnabled=1 |
| 161 | gNeighborScanTimerPeriod=200 |
| 162 | |
| 163 | gNeighborLookupThreshold=76 |
| 164 | gNeighborReassocThreshold=81 |
| 165 | |
| 166 | gNeighborScanChannelMinTime=20 |
| 167 | gNeighborScanChannelMaxTime=30 |
| 168 | gMaxNeighborReqTries=3 |
| 169 | |
| 170 | # Legacy (non-CCX, non-802.11r) Fast Roaming Support |
| 171 | # To enable, set FastRoamEnabled=1, gEnableFWRssiMonitoring=1, FastTransitionEnabled=1 |
| 172 | # To disable, set FastRoamEnabled=0, gEnableFWRssiMonitoring=0, FastTransitionEnabled=0 |
| 173 | FastRoamEnabled=1 |
| 174 | |
| 175 | #Check if the AP to which we are roaming is better than current AP in terms of RSSI. |
| 176 | #Checking is disabled if set to Zero.Otherwise it will use this value as to how better |
| 177 | #the RSSI of the new/roamable AP should be for roaming |
| 178 | RoamRssiDiff=3 |
| 179 | |
| 180 | #Configure the RSSI gap that will be used to partition/categorize width of |
| 181 | #each individual category (aka bucket). |
| 182 | gRssiCatGap=5 |
| 183 | |
| 184 | #Prefer 5GHz APs while roaming (default is gRoamPrefer5GHz=1) |
| 185 | gRoamPrefer5GHz=1 |
| 186 | |
| 187 | # SAP Country code |
| 188 | |
| 189 | # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. |
| 190 | |
| 191 | # Example |
| 192 | |
| 193 | # US Indoor, USI |
| 194 | |
| 195 | # Korea Outdoor, KRO |
| 196 | |
| 197 | # Japan without optional byte, JP |
| 198 | |
| 199 | # France without optional byte, FR |
| 200 | |
| 201 | #gAPCntryCode=USI |
| 202 | |
| 203 | |
| 204 | #Short Guard Interval Enable/disable |
| 205 | |
| 206 | gShortGI20Mhz=1 |
| 207 | |
| 208 | gShortGI40Mhz=1 |
| 209 | |
| 210 | |
| 211 | #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled |
| 212 | |
| 213 | gAPAutoShutOff=0 |
| 214 | |
| 215 | |
| 216 | # SAP auto channel selection configuration |
| 217 | |
| 218 | # 0 = disable auto channel selection |
| 219 | |
| 220 | # 1 = enable auto channel selection, channel provided by supplicant will be ignored |
| 221 | |
| 222 | gApAutoChannelSelection=0 |
| 223 | |
| 224 | |
| 225 | # Listen Energy Detect Mode Configuration |
| 226 | |
| 227 | # Valid values 0-128 |
| 228 | |
| 229 | # 128 means disable Energy Detect feature |
| 230 | |
| 231 | # 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. |
| 232 | |
| 233 | # 10-128 are reserved. |
| 234 | |
| 235 | # The EDET threshold mapping is as follows in 3dB step: |
| 236 | |
| 237 | # 0 = -60 dBm |
| 238 | |
| 239 | # 1 = -63 dBm |
| 240 | |
| 241 | # 2 = -66 dBm |
| 242 | |
| 243 | # ... |
| 244 | |
| 245 | # 7 = -81 dBm |
| 246 | |
| 247 | # 8 = -84 dBm |
| 248 | |
| 249 | # 9 = -87 dBm |
| 250 | |
| 251 | # Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: |
| 252 | |
| 253 | # |
| 254 | |
| 255 | # Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. |
| 256 | |
| 257 | # |
| 258 | |
| 259 | gEnablePhyAgcListenMode=128 |
| 260 | |
| 261 | |
| 262 | #Preferred channel to start BT AMP AP mode (0 means, any channel) |
| 263 | |
| 264 | BtAmpPreferredChannel=0 |
| 265 | |
| 266 | |
| 267 | #Preferred band (both or 2.4 only or 5 only) |
| 268 | |
| 269 | BandCapability=0 |
| 270 | |
| 271 | |
| 272 | #Beacon Early Termination (1 = enable the BET feature, 0 = disable) |
| 273 | |
| 274 | enableBeaconEarlyTermination=0 |
| 275 | |
| 276 | beaconEarlyTerminationWakeInterval=3 |
| 277 | |
| 278 | |
| 279 | #Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable) |
| 280 | |
| 281 | gEnableBtAmp=0 |
| 282 | |
| 283 | |
| 284 | #SOFTAP Channel Range selection |
| 285 | |
| 286 | gAPChannelSelectStartChannel=1 |
| 287 | |
| 288 | gAPChannelSelectEndChannel=11 |
| 289 | |
| 290 | |
| 291 | #SOFTAP Channel Range selection Operating band |
| 292 | |
| 293 | # 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND |
| 294 | |
| 295 | gAPChannelSelectOperatingBand=0 |
| 296 | |
| 297 | |
| 298 | #Channel Bonding |
| 299 | gChannelBondingMode5GHz=6 |
| 300 | |
| 301 | |
| 302 | #Enable Keep alive with non-zero period value |
| 303 | |
| 304 | #gStaKeepAlivePeriod = 30 |
| 305 | |
| 306 | |
| 307 | #If set will start with active scan after driver load, otherwise will start with |
| 308 | |
| 309 | #passive scan to find out the domain |
| 310 | |
| 311 | #gEnableBypass11d=1 |
| 312 | |
| 313 | |
| 314 | #If set to 0, will not scan DFS channels |
| 315 | |
| 316 | gEnableDFSChnlScan=1 |
| 317 | |
| 318 | |
| 319 | gVhtChannelWidth=2 |
| 320 | gEnableLogp=1 |
| 321 | |
| 322 | |
| 323 | # Enable Automatic Tx Power control |
| 324 | |
| 325 | gEnableAutomaticTxPowerControl=1 |
| 326 | |
| 327 | # 0 for OLPC 1 for CLPC and SCPC |
| 328 | gEnableCloseLoop=1 |
| 329 | |
| 330 | #Data Inactivity Timeout when in powersave (in ms) |
| 331 | gDataInactivityTimeout=200 |
| 332 | |
| 333 | # VHT Tx/Rx MCS values |
| 334 | # Valid values are 0,1,2. If commented out, the default value is 0. |
| 335 | # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| 336 | gVhtRxMCS=2 |
| 337 | gVhtTxMCS=2 |
| 338 | |
| 339 | gEnableLpwrImgTransition=1 |
| 340 | |
| 341 | # Enable Tx beamforming |
| 342 | gTxBFEnable=1 |
| 343 | |
| 344 | # Enable Tx LDPC |
| 345 | #gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT |
| 346 | gTxLdpcEnable=3 |
| 347 | |
| 348 | END |
| 349 | |
| 350 | # Note: Configuration parser would not read anything past the END marker |
| 351 | |