blob: 881609ef85e82dbf2b024f800acbac956cfae7d3 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001#
2# USB Host Controller Drivers
3#
4comment "USB Host Controller Drivers"
Linus Torvalds1da177e2005-04-16 15:20:36 -07005
Peter Korsgaarde9b29ff2008-04-27 08:59:45 +02006config USB_C67X00_HCD
7 tristate "Cypress C67x00 HCD support"
Peter Korsgaarde9b29ff2008-04-27 08:59:45 +02008 help
9 The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role
10 host/peripheral/OTG USB controllers.
11
12 Enable this option to support this chip in host controller mode.
13 If unsure, say N.
14
15 To compile this driver as a module, choose M here: the
16 module will be called c67x00.
17
Sarah Sharpeb6bab12009-04-29 19:07:13 -070018config USB_XHCI_HCD
Greg Kroah-Hartmaneb83be92012-09-14 21:15:50 -070019 tristate "xHCI HCD (USB 3.0) support"
Sarah Sharpeb6bab12009-04-29 19:07:13 -070020 ---help---
21 The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
22 "SuperSpeed" host controller hardware.
23
24 To compile this driver as a module, choose M here: the
25 module will be called xhci-hcd.
26
Florian Fainelli0fcb9982013-04-09 14:29:29 +020027if USB_XHCI_HCD
28
Sebastian Andrzej Siewior3429e912012-03-13 16:57:41 +020029config USB_XHCI_PLATFORM
30 tristate
Sebastian Andrzej Siewior3429e912012-03-13 16:57:41 +020031
Sarah Sharpeb6bab12009-04-29 19:07:13 -070032config USB_XHCI_HCD_DEBUGGING
33 bool "Debugging for the xHCI host controller"
Sarah Sharpeb6bab12009-04-29 19:07:13 -070034 ---help---
35 Say 'Y' to turn on debugging for the xHCI host controller driver.
36 This will spew debugging output, even in interrupt context.
37 This should only be used for debugging xHCI driver bugs.
38
39 If unsure, say N.
40
Florian Fainelli0fcb9982013-04-09 14:29:29 +020041endif # USB_XHCI_HCD
42
Linus Torvalds1da177e2005-04-16 15:20:36 -070043config USB_EHCI_HCD
44 tristate "EHCI HCD (USB 2.0) support"
Linus Torvalds1da177e2005-04-16 15:20:36 -070045 ---help---
46 The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
47 "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
48 If your USB host controller supports USB 2.0, you will likely want to
Thierry Vignaudb967c882009-02-11 13:31:05 -080049 configure this Host Controller Driver.
Linus Torvalds1da177e2005-04-16 15:20:36 -070050
51 EHCI controllers are packaged with "companion" host controllers (OHCI
52 or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports
Jesper Juhlb3c29d82006-01-10 00:35:22 +010053 will connect to EHCI if the device is high speed, otherwise they
Linus Torvalds1da177e2005-04-16 15:20:36 -070054 connect to a companion controller. If you configure EHCI, you should
55 probably configure the OHCI (for NEC and some other vendors) USB Host
56 Controller Driver or UHCI (for Via motherboards) Host Controller
57 Driver too.
58
59 You may want to read <file:Documentation/usb/ehci.txt>.
60
61 To compile this driver as a module, choose M here: the
62 module will be called ehci-hcd.
63
Linus Torvalds1da177e2005-04-16 15:20:36 -070064config USB_EHCI_ROOT_HUB_TT
Robert P. J. Day9ec249a2008-03-08 03:27:44 -050065 bool "Root Hub Transaction Translators"
Marek Vasutb12909b2012-05-15 06:10:20 +020066 depends on USB_EHCI_HCD || USB_CHIPIDEA_HOST
Linus Torvalds1da177e2005-04-16 15:20:36 -070067 ---help---
68 Some EHCI chips have vendor-specific extensions to integrate
69 transaction translators, so that no OHCI or UHCI companion
70 controller is needed. It's safe to say "y" even if your
71 controller doesn't support this feature.
72
Dan Streetmanba47f662006-05-24 09:39:16 -070073 This supports the EHCI implementation that's originally
74 from ARC, and has since changed hands a few times.
75
76config USB_EHCI_TT_NEWSCHED
Alan Stern37cd6812010-05-21 17:08:21 -040077 bool "Improved Transaction Translator scheduling"
Marek Vasutb12909b2012-05-15 06:10:20 +020078 depends on USB_EHCI_HCD || USB_CHIPIDEA_HOST
Alan Stern37cd6812010-05-21 17:08:21 -040079 default y
Dan Streetmanba47f662006-05-24 09:39:16 -070080 ---help---
81 This changes the periodic scheduling code to fill more of the low
82 and full speed bandwidth available from the Transaction Translator
83 (TT) in USB 2.0 hubs. Without this, only one transfer will be
84 issued in each microframe, significantly reducing the number of
85 periodic low/fullspeed transfers possible.
86
87 If you have multiple periodic low/fullspeed devices connected to a
88 highspeed USB hub which is connected to a highspeed USB Host
89 Controller, and some of those devices will not work correctly
Alan Stern37cd6812010-05-21 17:08:21 -040090 (possibly due to "ENOSPC" or "-28" errors), say Y. Conversely, if
91 you have only one such device and it doesn't work, you could try
92 saying N.
Dan Streetmanba47f662006-05-24 09:39:16 -070093
Alan Stern37cd6812010-05-21 17:08:21 -040094 If unsure, say Y.
Linus Torvalds1da177e2005-04-16 15:20:36 -070095
Florian Fainelli42443dc2013-04-09 14:29:27 +020096config USB_FSL_MPH_DR_OF
97 tristate
98
99if USB_EHCI_HCD
100
Alan Sternadfa79d2012-11-01 11:13:04 -0400101config USB_EHCI_PCI
102 tristate
Florian Fainelli42443dc2013-04-09 14:29:27 +0200103 depends on PCI
Alan Sternadfa79d2012-11-01 11:13:04 -0400104 default y
105
Anoop22ced6872011-02-24 19:26:28 +0530106config USB_EHCI_HCD_PMC_MSP
107 tristate "EHCI support for on-chip PMC MSP71xx USB controller"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200108 depends on MSP_HAS_USB
Anoop22ced6872011-02-24 19:26:28 +0530109 default n
110 select USB_EHCI_BIG_ENDIAN_DESC
111 select USB_EHCI_BIG_ENDIAN_MMIO
112 ---help---
113 Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's.
114 If unsure, say N.
115
Benjamin Herrenschmidt083522d2006-12-15 06:54:08 +1100116config USB_EHCI_BIG_ENDIAN_MMIO
117 bool
Benjamin Herrenschmidt083522d2006-12-15 06:54:08 +1100118
Stefan Roese6dbd6822007-05-01 09:29:37 -0700119config USB_EHCI_BIG_ENDIAN_DESC
120 bool
Stefan Roese6dbd6822007-05-01 09:29:37 -0700121
Julie Zhu08d3c182009-09-21 16:08:19 -0600122config XPS_USB_HCD_XILINX
123 bool "Use Xilinx usb host EHCI controller core"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200124 depends on (PPC32 || MICROBLAZE)
Julie Zhu08d3c182009-09-21 16:08:19 -0600125 select USB_EHCI_BIG_ENDIAN_DESC
126 select USB_EHCI_BIG_ENDIAN_MMIO
127 ---help---
128 Xilinx xps USB host controller core is EHCI compilant and has
129 transaction translator built-in. It can be configured to either
130 support both high speed and full speed devices, or high speed
131 devices only.
132
Li Yangba029782007-05-11 17:09:55 +0800133config USB_EHCI_FSL
Fabio Estevamc0ca9bc2012-02-02 14:23:34 -0200134 bool "Support for Freescale PPC on-chip EHCI USB controller"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200135 depends on FSL_SOC
Li Yangba029782007-05-11 17:09:55 +0800136 select USB_EHCI_ROOT_HUB_TT
Marc Kleine-Budde018b97d2010-10-29 11:04:49 +0200137 select USB_FSL_MPH_DR_OF if OF
Li Yangba029782007-05-11 17:09:55 +0800138 ---help---
139 Variation of ARC USB block used in some Freescale chips.
140
Daniel Mack7e8d5cd2009-10-28 01:14:59 +0100141config USB_EHCI_MXC
Alan Sterndba63b22013-01-23 13:26:15 -0500142 tristate "Support for Freescale i.MX on-chip EHCI USB controller"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200143 depends on ARCH_MXC
Daniel Mack7e8d5cd2009-10-28 01:14:59 +0100144 select USB_EHCI_ROOT_HUB_TT
145 ---help---
146 Variation of ARC USB block used in some Freescale chips.
147
Keshava Munegowda7f124f42010-11-21 23:23:41 +0530148config USB_EHCI_HCD_OMAP
Alan Stern54a419662013-03-12 12:44:39 +0200149 tristate "EHCI support for OMAP3 and later chips"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200150 depends on ARCH_OMAP
Keshava Munegowda7f124f42010-11-21 23:23:41 +0530151 default y
Paul Bolled132d7f2012-05-07 11:14:59 +0200152 ---help---
Keshava Munegowda7f124f42010-11-21 23:23:41 +0530153 Enables support for the on-chip EHCI controller on
154 OMAP3 and later chips.
Roger Quadros7c4ebe682013-04-15 14:50:34 +0300155 If your system uses a PHY on the USB port, you will need to
156 enable USB_PHY and the appropriate PHY driver as well. Most
157 boards need the NOP_USB_XCEIV PHY driver.
Keshava Munegowda7f124f42010-11-21 23:23:41 +0530158
Manjunath Goudara76dd462013-04-02 18:23:59 +0200159config USB_EHCI_HCD_ORION
160 tristate "Support for Marvell EBU on-chip EHCI USB controller"
161 depends on USB_EHCI_HCD && PLAT_ORION
162 default y
163 ---help---
164 Enables support for the on-chip EHCI controller on Marvell's
165 embedded ARM SoCs, including Orion, Kirkwood, Dove, Armada XP,
166 Armada 370. This is different from the EHCI implementation
167 on Marvell's mobile PXA and MMP SoC, see "EHCI support for
168 Marvell PXA/MMP USB controller" for those.
169
Manjunath Goudar7675d6b2013-04-02 18:24:00 +0200170config USB_EHCI_HCD_SPEAR
171 tristate "Support for ST SPEAr on-chip EHCI USB controller"
172 depends on USB_EHCI_HCD && PLAT_SPEAR
173 default y
174 ---help---
175 Enables support for the on-chip EHCI controller on
176 ST SPEAr chips.
177
Manjunath Goudar97736962013-04-02 18:24:02 +0200178config USB_EHCI_HCD_AT91
179 tristate "Support for Atmel on-chip EHCI USB controller"
180 depends on USB_EHCI_HCD && ARCH_AT91
181 default y
182 ---help---
183 Enables support for the on-chip EHCI controller on
184 Atmel chips.
185
Pavankumar Kondetib0848ae2010-12-07 17:53:56 +0530186config USB_EHCI_MSM
Manjunath Goudar8c68e842013-04-02 18:24:03 +0200187 tristate "Support for Qualcomm QSD/MSM on-chip EHCI USB controller"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200188 depends on ARCH_MSM
Arnd Bergmann4626b8d2013-04-25 19:29:01 +0200189 depends on USB_PHY
Pavankumar Kondetib0848ae2010-12-07 17:53:56 +0530190 select USB_EHCI_ROOT_HUB_TT
Pavankumar Kondetidfb21302011-03-04 22:45:02 +0530191 select USB_MSM_OTG
Pavankumar Kondetib0848ae2010-12-07 17:53:56 +0530192 ---help---
193 Enables support for the USB Host controller present on the
194 Qualcomm chipsets. Root Hub has inbuilt TT.
195 This driver depends on OTG driver for PHY initialization,
Pavankumar Kondeti8bb6a162010-12-07 17:53:57 +0530196 clock management, powering up VBUS, and power management.
Pavankumar Kondeti8cf28f12011-02-04 10:08:18 +0530197 This driver is not supported on boards like trout which
198 has an external PHY.
Pavankumar Kondetib0848ae2010-12-07 17:53:56 +0530199
Benoit Goby79ad3b52011-03-09 16:28:56 -0800200config USB_EHCI_TEGRA
201 boolean "NVIDIA Tegra HCD support"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200202 depends on ARCH_TEGRA
Benoit Goby79ad3b52011-03-09 16:28:56 -0800203 select USB_EHCI_ROOT_HUB_TT
Felipe Balbi75f32ec2013-03-20 14:18:28 +0200204 select USB_PHY
Benoit Goby79ad3b52011-03-09 16:28:56 -0800205 help
206 This driver enables support for the internal USB Host Controllers
207 found in NVIDIA Tegra SoCs. The controllers are EHCI compliant.
208
Valentine Barshakda0e8fb2007-12-30 15:28:50 -0800209config USB_EHCI_HCD_PPC_OF
210 bool "EHCI support for PPC USB controller on OF platform bus"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200211 depends on PPC_OF
Valentine Barshakda0e8fb2007-12-30 15:28:50 -0800212 default y
213 ---help---
214 Enables support for the USB controller present on the PowerPC
215 OpenFirmware platform bus.
216
Yoshihiro Shimoda60b0bf02011-03-01 16:58:37 +0900217config USB_EHCI_SH
218 bool "EHCI support for SuperH USB controller"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200219 depends on SUPERH
Yoshihiro Shimoda60b0bf02011-03-01 16:58:37 +0900220 ---help---
221 Enables support for the on-chip EHCI controller on the SuperH.
222 If you use the PCI EHCI controller, this option is not necessary.
223
Joonyoung Shim1bcc5aa2011-04-08 14:08:50 +0900224config USB_EHCI_S5P
Manjunath Goudar7edb3da2013-04-02 18:24:01 +0200225 tristate "EHCI support for Samsung S5P/EXYNOS SoC Series"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200226 depends on PLAT_S5P
Greg Kroah-Hartmane9a92b22013-02-20 10:25:05 -0800227 help
Manjunath Goudar7edb3da2013-04-02 18:24:01 +0200228 Enable support for the Samsung S5Pxxxx and Exynos3/4/5 SOC's
229 on-chip EHCI controller.
Joonyoung Shim1bcc5aa2011-04-08 14:08:50 +0900230
Neil Zhang3a082ec2011-12-20 13:20:23 +0800231config USB_EHCI_MV
Manjunath Goudara76dd462013-04-02 18:23:59 +0200232 bool "EHCI support for Marvell PXA/MMP USB controller"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200233 depends on (ARCH_PXA || ARCH_MMP)
Neil Zhang3a082ec2011-12-20 13:20:23 +0800234 select USB_EHCI_ROOT_HUB_TT
235 ---help---
236 Enables support for Marvell (including PXA and MMP series) on-chip
237 USB SPH and OTG controller. SPH is a single port host, and it can
238 only be EHCI host. OTG is controller that can switch to host mode.
Manjunath Goudara76dd462013-04-02 18:23:59 +0200239 Note that this driver will not work on Marvell's other EHCI
240 controller used by the EBU-type SoCs including Orion, Kirkwood,
241 Dova, Armada 370 and Armada XP. See "Support for Marvell EBU
242 on-chip EHCI USB controller" for those.
Neil Zhang3a082ec2011-12-20 13:20:23 +0800243
Wan ZongShun586dfc82009-06-13 09:14:28 +0800244config USB_W90X900_EHCI
245 bool "W90X900(W90P910) EHCI support"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200246 depends on ARCH_W90X900
Wan ZongShun586dfc82009-06-13 09:14:28 +0800247 ---help---
248 Enables support for the W90X900 USB controller
249
Mac Lin760efe62010-11-25 23:58:00 +0800250config USB_CNS3XXX_EHCI
Florian Fainellif3a958d2012-10-08 15:11:25 +0200251 bool "Cavium CNS3XXX EHCI Module (DEPRECATED)"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200252 depends on ARCH_CNS3XXX
Florian Fainellif3a958d2012-10-08 15:11:25 +0200253 select USB_EHCI_HCD_PLATFORM
Mac Lin760efe62010-11-25 23:58:00 +0800254 ---help---
Florian Fainellif3a958d2012-10-08 15:11:25 +0200255 This option is deprecated now and the driver was removed, use
256 USB_EHCI_HCD_PLATFORM instead.
257
Mac Lin760efe62010-11-25 23:58:00 +0800258 Enable support for the CNS3XXX SOC's on-chip EHCI controller.
259 It is needed for high-speed (480Mbit/sec) USB 2.0 device
260 support.
261
Gabor Juhos502fa842011-04-13 10:54:22 +0200262config USB_EHCI_ATH79
Hauke Mehrtens5d98cd42012-03-13 01:04:53 +0100263 bool "EHCI support for AR7XXX/AR9XXX SoCs (DEPRECATED)"
Florian Fainelli42443dc2013-04-09 14:29:27 +0200264 depends on (SOC_AR71XX || SOC_AR724X || SOC_AR913X || SOC_AR933X)
Gabor Juhos502fa842011-04-13 10:54:22 +0200265 select USB_EHCI_ROOT_HUB_TT
Hauke Mehrtens5d98cd42012-03-13 01:04:53 +0100266 select USB_EHCI_HCD_PLATFORM
Gabor Juhos502fa842011-04-13 10:54:22 +0200267 default y
268 ---help---
Hauke Mehrtens5d98cd42012-03-13 01:04:53 +0100269 This option is deprecated now and the driver was removed, use
270 USB_EHCI_HCD_PLATFORM instead.
271
Gabor Juhos502fa842011-04-13 10:54:22 +0200272 Enables support for the built-in EHCI controller present
273 on the Atheros AR7XXX/AR9XXX SoCs.
274
Florian Fainelli42443dc2013-04-09 14:29:27 +0200275config USB_EHCI_HCD_PLATFORM
276 tristate "Generic EHCI driver for a platform device"
277 default n
278 ---help---
279 Adds an EHCI host driver for a generic platform device, which
280 provides a memory space and an irq.
281
282 If unsure, say N.
283
284config USB_OCTEON_EHCI
285 bool "Octeon on-chip EHCI support"
286 depends on CPU_CAVIUM_OCTEON
287 default n
288 select USB_EHCI_BIG_ENDIAN_MMIO
289 help
290 Enable support for the Octeon II SOC's on-chip EHCI
291 controller. It is needed for high-speed (480Mbit/sec)
292 USB 2.0 device support. All CN6XXX based chips with USB are
293 supported.
294
295endif # USB_EHCI_HCD
296
Rodolfo Giomettib92a78e2008-10-23 10:08:07 +0200297config USB_OXU210HP_HCD
298 tristate "OXU210HP HCD support"
Florian Fainelli25e11ec2013-04-09 14:29:25 +0200299 depends on GENERIC_HARDIRQS
Rodolfo Giomettib92a78e2008-10-23 10:08:07 +0200300 ---help---
301 The OXU210HP is an USB host/OTG/device controller. Enable this
302 option if your board has this chip. If unsure, say N.
303
304 This driver does not support isochronous transfers and doesn't
305 implement OTG nor USB device controllers.
306
307 To compile this driver as a module, choose M here: the
308 module will be called oxu210hp-hcd.
309
Olav Kongas4808a1c2005-04-09 22:57:39 +0300310config USB_ISP116X_HCD
311 tristate "ISP116X HCD support"
Olav Kongas4808a1c2005-04-09 22:57:39 +0300312 ---help---
313 The ISP1160 and ISP1161 chips are USB host controllers. Enable this
314 option if your board has this chip. If unsure, say N.
315
316 This driver does not support isochronous transfers.
317
318 To compile this driver as a module, choose M here: the
319 module will be called isp116x-hcd.
320
Sebastian Siewiordb11e472008-04-24 00:37:04 +0200321config USB_ISP1760_HCD
322 tristate "ISP 1760 HCD support"
Sebastian Siewiordb11e472008-04-24 00:37:04 +0200323 ---help---
324 The ISP1760 chip is a USB 2.0 host controller.
325
326 This driver does not support isochronous transfers or OTG.
Sebastian Andrzej Siewiorff30bf12008-11-02 15:25:42 +0100327 This USB controller is usually attached to a non-DMA-Master
328 capable bus. NXP's eval kit brings this chip on PCI card
329 where the chip itself is behind a PLB to simulate such
330 a bus.
Sebastian Siewiordb11e472008-04-24 00:37:04 +0200331
332 To compile this driver as a module, choose M here: the
Sebastian Andrzej Siewiorff30bf12008-11-02 15:25:42 +0100333 module will be called isp1760.
Sebastian Siewiordb11e472008-04-24 00:37:04 +0200334
Lothar Wassmanna9d43092009-07-16 20:51:21 -0400335config USB_ISP1362_HCD
336 tristate "ISP1362 HCD support"
Lothar Wassmanna9d43092009-07-16 20:51:21 -0400337 default N
338 ---help---
339 Supports the Philips ISP1362 chip as a host controller
340
341 This driver does not support isochronous transfers.
342
343 To compile this driver as a module, choose M here: the
344 module will be called isp1362-hcd.
345
Yuan-Hsin Chen6c920bfb2013-05-17 10:14:14 +0000346config USB_FUSBH200_HCD
347 tristate "FUSBH200 HCD support"
348 depends on USB
349 default N
350 ---help---
351 Faraday FUSBH200 is designed to meet USB2.0 EHCI specification
352 with minor modification.
353
354 To compile this driver as a module, choose M here: the
355 module will be called fusbh200-hcd.
356
Linus Torvalds1da177e2005-04-16 15:20:36 -0700357config USB_OHCI_HCD
Manjunath Goudarc1117af2013-05-28 18:34:51 +0530358 tristate "OHCI HCD (USB 1.1) support"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700359 select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3
Linus Torvalds61464c82012-10-01 18:19:05 -0700360 depends on USB_ISP1301 || !ARCH_LPC32XX
Linus Torvalds1da177e2005-04-16 15:20:36 -0700361 ---help---
362 The Open Host Controller Interface (OHCI) is a standard for accessing
363 USB 1.1 host controller hardware. It does more in hardware than Intel's
364 UHCI specification. If your USB host controller follows the OHCI spec,
365 say Y. On most non-x86 systems, and on x86 hardware that's not using a
366 USB controller from Intel or VIA, this is appropriate. If your host
367 controller doesn't use PCI, this is probably appropriate. For a PCI
368 based system where you're not sure, the "lspci -v" entry will list the
369 right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI.
370
371 To compile this driver as a module, choose M here: the
372 module will be called ohci-hcd.
373
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200374if USB_OHCI_HCD
375
Anand Gadiyar968b4482010-05-10 21:56:12 +0530376config USB_OHCI_HCD_OMAP1
377 bool "OHCI support for OMAP1/2 chips"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200378 depends on ARCH_OMAP1
Anand Gadiyar968b4482010-05-10 21:56:12 +0530379 default y
380 ---help---
381 Enables support for the OHCI controller on OMAP1/2 chips.
382
383config USB_OHCI_HCD_OMAP3
384 bool "OHCI support for OMAP3 and later chips"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200385 depends on (ARCH_OMAP3 || ARCH_OMAP4)
Anand Gadiyar968b4482010-05-10 21:56:12 +0530386 default y
387 ---help---
388 Enables support for the on-chip OHCI controller on
389 OMAP3 and later chips.
390
Gabor Juhos90e6ca52011-04-13 10:54:24 +0200391config USB_OHCI_ATH79
Hauke Mehrtens5d98cd42012-03-13 01:04:53 +0100392 bool "USB OHCI support for the Atheros AR71XX/AR7240 SoCs (DEPRECATED)"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200393 depends on (SOC_AR71XX || SOC_AR724X)
Hauke Mehrtens5d98cd42012-03-13 01:04:53 +0100394 select USB_OHCI_HCD_PLATFORM
Gabor Juhos90e6ca52011-04-13 10:54:24 +0200395 default y
396 help
Hauke Mehrtens5d98cd42012-03-13 01:04:53 +0100397 This option is deprecated now and the driver was removed, use
398 USB_OHCI_HCD_PLATFORM instead.
399
Gabor Juhos90e6ca52011-04-13 10:54:24 +0200400 Enables support for the built-in OHCI controller present on the
401 Atheros AR71XX/AR7240 SoCs.
402
Sylvain Munaut495a6782006-12-13 21:09:55 +0100403config USB_OHCI_HCD_PPC_OF_BE
Arnd Bergmann45e83882009-06-19 05:35:34 -0700404 bool "OHCI support for OF platform bus (big endian)"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200405 depends on PPC_OF
Sylvain Munaut495a6782006-12-13 21:09:55 +0100406 select USB_OHCI_BIG_ENDIAN_DESC
407 select USB_OHCI_BIG_ENDIAN_MMIO
Arnd Bergmann45e83882009-06-19 05:35:34 -0700408 ---help---
409 Enables support for big-endian USB controllers present on the
410 OpenFirmware platform bus.
Sylvain Munaut495a6782006-12-13 21:09:55 +0100411
412config USB_OHCI_HCD_PPC_OF_LE
Arnd Bergmann45e83882009-06-19 05:35:34 -0700413 bool "OHCI support for OF platform bus (little endian)"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200414 depends on PPC_OF
Sylvain Munaut495a6782006-12-13 21:09:55 +0100415 select USB_OHCI_LITTLE_ENDIAN
Arnd Bergmann45e83882009-06-19 05:35:34 -0700416 ---help---
417 Enables support for little-endian USB controllers present on the
418 OpenFirmware platform bus.
419
420config USB_OHCI_HCD_PPC_OF
421 bool
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200422 depends on PPC_OF
Arnd Bergmann45e83882009-06-19 05:35:34 -0700423 default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE
Sylvain Munaut495a6782006-12-13 21:09:55 +0100424
Linus Torvalds1da177e2005-04-16 15:20:36 -0700425config USB_OHCI_HCD_PCI
Manjunath Goudarc1117af2013-05-28 18:34:51 +0530426 tristate "OHCI support for PCI-bus USB controllers"
427 depends on PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700428 default y
429 select USB_OHCI_LITTLE_ENDIAN
430 ---help---
431 Enables support for PCI-bus plug-in USB controller cards.
432 If unsure, say Y.
433
Michael Bueschc604e852007-10-09 23:47:17 -0700434config USB_OHCI_HCD_SSB
Hauke Mehrtens259b83a2012-03-15 23:49:59 +0100435 bool "OHCI support for Broadcom SSB OHCI core (DEPRECATED)"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200436 depends on (SSB = y || SSB = USB_OHCI_HCD)
Hauke Mehrtens259b83a2012-03-15 23:49:59 +0100437 select USB_HCD_SSB
438 select USB_OHCI_HCD_PLATFORM
Michael Bueschc604e852007-10-09 23:47:17 -0700439 default n
440 ---help---
Hauke Mehrtens259b83a2012-03-15 23:49:59 +0100441 This option is deprecated now and the driver was removed, use
442 USB_HCD_SSB and USB_OHCI_HCD_PLATFORM instead.
443
Michael Bueschc604e852007-10-09 23:47:17 -0700444 Support for the Sonics Silicon Backplane (SSB) attached
445 Broadcom USB OHCI core.
446
447 This device is present in some embedded devices with
448 Broadcom based SSB bus.
449
450 If unsure, say N.
451
Yoshihiro Shimoda60b0bf02011-03-01 16:58:37 +0900452config USB_OHCI_SH
Florian Fainelli231a72e2012-10-08 15:11:37 +0200453 bool "OHCI support for SuperH USB controller (DEPRECATED)"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200454 depends on SUPERH
Florian Fainelli231a72e2012-10-08 15:11:37 +0200455 select USB_OHCI_HCD_PLATFORM
Yoshihiro Shimoda60b0bf02011-03-01 16:58:37 +0900456 ---help---
Florian Fainelli231a72e2012-10-08 15:11:37 +0200457 This option is deprecated now and the driver was removed, use
458 USB_OHCI_HCD_PLATFORM instead.
459
Yoshihiro Shimoda60b0bf02011-03-01 16:58:37 +0900460 Enables support for the on-chip OHCI controller on the SuperH.
461 If you use the PCI OHCI controller, this option is not necessary.
462
Jingoo Han62194242011-12-23 11:20:54 +0900463config USB_OHCI_EXYNOS
464 boolean "OHCI support for Samsung EXYNOS SoC Series"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200465 depends on ARCH_EXYNOS
Jingoo Han62194242011-12-23 11:20:54 +0900466 help
467 Enable support for the Samsung Exynos SOC's on-chip OHCI controller.
468
Mac Lin760efe62010-11-25 23:58:00 +0800469config USB_CNS3XXX_OHCI
Florian Fainellic23920b02012-10-08 15:11:33 +0200470 bool "Cavium CNS3XXX OHCI Module (DEPRECATED)"
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200471 depends on ARCH_CNS3XXX
Florian Fainellic23920b02012-10-08 15:11:33 +0200472 select USB_OHCI_HCD_PLATFORM
Mac Lin760efe62010-11-25 23:58:00 +0800473 ---help---
Florian Fainellic23920b02012-10-08 15:11:33 +0200474 This option is deprecated now and the driver was removed, use
475 USB_OHCI_HCD_PLATFORM instead.
476
Mac Lin760efe62010-11-25 23:58:00 +0800477 Enable support for the CNS3XXX SOC's on-chip OHCI controller.
478 It is needed for low-speed USB 1.0 device support.
479
Hauke Mehrtensfa3364b2012-03-13 01:04:47 +0100480config USB_OHCI_HCD_PLATFORM
Manjunath Goudar928fb682013-06-03 20:46:08 +0530481 tristate "Generic OHCI driver for a platform device"
Hauke Mehrtensfa3364b2012-03-13 01:04:47 +0100482 default n
483 ---help---
484 Adds an OHCI host driver for a generic platform device, which
Peter Meerwald898d8282012-08-18 15:53:12 +0200485 provides a memory space and an irq.
Hauke Mehrtensfa3364b2012-03-13 01:04:47 +0100486
487 If unsure, say N.
488
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200489config USB_OCTEON_OHCI
490 bool "Octeon on-chip OHCI support"
491 depends on CPU_CAVIUM_OCTEON
492 default USB_OCTEON_EHCI
493 select USB_OHCI_BIG_ENDIAN_MMIO
494 select USB_OHCI_LITTLE_ENDIAN
495 help
496 Enable support for the Octeon II SOC's on-chip OHCI
497 controller. It is needed for low-speed USB 1.0 device
498 support. All CN6XXX based chips with USB are supported.
499
Hauke Mehrtens7a7a4a592012-03-13 01:04:48 +0100500
Benjamin Herrenschmidt11d1a4a2006-12-15 06:54:03 +1100501config USB_OHCI_BIG_ENDIAN_DESC
502 bool
Benjamin Herrenschmidt11d1a4a2006-12-15 06:54:03 +1100503 default n
504
505config USB_OHCI_BIG_ENDIAN_MMIO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700506 bool
Linus Torvalds1da177e2005-04-16 15:20:36 -0700507 default n
508
509config USB_OHCI_LITTLE_ENDIAN
510 bool
Linus Torvalds1da177e2005-04-16 15:20:36 -0700511 default n if STB03xxx || PPC_MPC52xx
512 default y
513
Florian Fainelli3ad3ca02013-04-09 14:29:28 +0200514endif # USB_OHCI_HCD
515
Linus Torvalds1da177e2005-04-16 15:20:36 -0700516config USB_UHCI_HCD
517 tristate "UHCI HCD (most Intel and VIA) support"
Alan Sternccd95092013-05-14 13:54:12 -0400518 depends on PCI || USB_UHCI_SUPPORT_NON_PCI_HC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700519 ---help---
520 The Universal Host Controller Interface is a standard by Intel for
521 accessing the USB hardware in the PC (which is also called the USB
522 host controller). If your USB host controller conforms to this
523 standard, you may want to say Y, but see below. All recent boards
524 with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
525 i810, i820) conform to this standard. Also all VIA PCI chipsets
526 (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
Jan Andersson3db77392011-05-06 12:00:18 +0200527 133) and LEON/GRLIB SoCs with the GRUSBHC controller.
528 If unsure, say Y.
Linus Torvalds1da177e2005-04-16 15:20:36 -0700529
530 To compile this driver as a module, choose M here: the
531 module will be called uhci-hcd.
532
Jan Anderssond3219d12011-05-06 12:00:17 +0200533config USB_UHCI_SUPPORT_NON_PCI_HC
534 bool
Alan Sternccd95092013-05-14 13:54:12 -0400535 default y if (SPARC_LEON || USB_UHCI_PLATFORM)
Tony Prisk100d4592012-07-21 22:58:53 +1200536
537config USB_UHCI_PLATFORM
Alan Sternccd95092013-05-14 13:54:12 -0400538 bool
Tony Prisk100d4592012-07-21 22:58:53 +1200539 default y if ARCH_VT8500
Jan Anderssond3219d12011-05-06 12:00:17 +0200540
Jan Andersson8452c672011-05-18 10:44:49 +0200541config USB_UHCI_BIG_ENDIAN_MMIO
542 bool
Alan Sternccd95092013-05-14 13:54:12 -0400543 default y if SPARC_LEON
Jan Andersson8452c672011-05-18 10:44:49 +0200544
Jan Andersson51e2f622011-05-18 10:44:51 +0200545config USB_UHCI_BIG_ENDIAN_DESC
546 bool
Alan Sternccd95092013-05-14 13:54:12 -0400547 default y if SPARC_LEON
Jan Andersson51e2f622011-05-18 10:44:51 +0200548
Anton Vorontsov236dd4d2009-01-10 05:03:21 +0300549config USB_FHCI_HCD
550 tristate "Freescale QE USB Host Controller support"
Florian Fainelli25e11ec2013-04-09 14:29:25 +0200551 depends on OF_GPIO && QE_GPIO && QUICC_ENGINE
Anton Vorontsov236dd4d2009-01-10 05:03:21 +0300552 select FSL_GTM
553 select QE_USB
554 help
555 This driver enables support for Freescale QE USB Host Controller
556 (as found on MPC8360 and MPC8323 processors), the driver supports
557 Full and Low Speed USB.
558
559config FHCI_DEBUG
560 bool "Freescale QE USB Host Controller debug support"
561 depends on USB_FHCI_HCD && DEBUG_FS
562 help
563 Say "y" to see some FHCI debug information and statistics
Lucas De Marchi25985ed2011-03-30 22:57:33 -0300564 through debugfs.
Anton Vorontsov236dd4d2009-01-10 05:03:21 +0300565
Tony Olechd774efe2006-09-13 11:27:35 +0100566config USB_U132_HCD
567 tristate "Elan U132 Adapter Host Controller"
Florian Fainelli25e11ec2013-04-09 14:29:25 +0200568 depends on USB_FTDI_ELAN
Tony Olechd774efe2006-09-13 11:27:35 +0100569 default M
570 help
571 The U132 adapter is a USB to CardBus adapter specifically designed
572 for PC cards that contain an OHCI host controller. Typical PC cards
573 are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
574 adapter will *NOT* work with PC cards that do not contain an OHCI
575 controller.
576
Matt LaPlante3cb2fcc2006-11-30 05:22:59 +0100577 For those PC cards that contain multiple OHCI controllers only the
Tony Olechd774efe2006-09-13 11:27:35 +0100578 first one is used.
579
580 The driver consists of two modules, the "ftdi-elan" module is a
581 USB client driver that interfaces to the FTDI chip within ELAN's
582 USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
583 controller driver that talks to the OHCI controller within the
584 CardBus cards that are inserted in the U132 adapter.
585
586 This driver has been tested with a CardBus OHCI USB adapter, and
587 worked with a USB PEN Drive inserted into the first USB port of
588 the PCCARD. A rather pointless thing to do, but useful for testing.
589
590 It is safe to say M here.
591
592 See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>
593
Linus Torvalds1da177e2005-04-16 15:20:36 -0700594config USB_SL811_HCD
595 tristate "SL811HS HCD support"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700596 help
597 The SL811HS is a single-port USB controller that supports either
598 host side or peripheral side roles. Enable this option if your
599 board has this chip, and you want to use it as a host controller.
600 If unsure, say N.
601
602 To compile this driver as a module, choose M here: the
603 module will be called sl811-hcd.
604
Mike Frysingerad7c56f2011-03-22 15:35:39 -0400605config USB_SL811_HCD_ISO
606 bool "partial ISO support"
607 depends on USB_SL811_HCD
608 help
609 The driver doesn't support iso_frame_desc (yet), but for some simple
610 devices that just queue one ISO frame per URB, then ISO transfers
611 "should" work using the normal urb status fields.
612
613 If unsure, say N.
614
David Brownellc6de2b62005-05-26 05:55:55 -0700615config USB_SL811_CS
616 tristate "CF/PCMCIA support for SL811HS HCD"
617 depends on USB_SL811_HCD && PCMCIA
David Brownellc6de2b62005-05-26 05:55:55 -0700618 help
619 Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC
620 REX-CFU1U CF card (often used with PDAs). If unsure, say N.
621
622 To compile this driver as a module, choose M here: the
623 module will be called "sl811_cs".
624
Yoshihiro Shimoda5d304352007-05-10 13:18:19 +0900625config USB_R8A66597_HCD
M4rkusXXLfa0de2b2007-08-10 14:53:32 -0700626 tristate "R8A66597 HCD support"
Yoshihiro Shimoda5d304352007-05-10 13:18:19 +0900627 help
628 The R8A66597 is a USB 2.0 host and peripheral controller.
629
630 Enable this option if your board has this chip, and you want
631 to use it as a host controller. If unsure, say N.
632
633 To compile this driver as a module, choose M here: the
634 module will be called r8a66597-hcd.
635
Kuninori Morimoto034d7c12011-10-10 22:07:40 -0700636config USB_RENESAS_USBHS_HCD
637 tristate "Renesas USBHS HCD support"
Kuninori Morimoto034d7c12011-10-10 22:07:40 -0700638 depends on USB_RENESAS_USBHS
639 help
640 The Renesas USBHS is a USB 2.0 host and peripheral controller.
641
642 Enable this option if your board has this chip, and you want
643 to use it as a host controller. If unsure, say N.
644
645 To compile this driver as a module, choose M here: the
646 module will be called renesas-usbhs.
647
David Vrabel7e6133a2008-09-17 16:34:28 +0100648config USB_WHCI_HCD
Greg Kroah-Hartmaneb83be92012-09-14 21:15:50 -0700649 tristate "Wireless USB Host Controller Interface (WHCI) driver"
Randy Dunlap36f8ecb2012-01-27 15:47:03 -0800650 depends on PCI && USB && UWB
David Vrabel7e6133a2008-09-17 16:34:28 +0100651 select USB_WUSB
652 select UWB_WHCI
653 help
654 A driver for PCI-based Wireless USB Host Controllers that are
655 compliant with the WHCI specification.
656
657 To compile this driver a module, choose M here: the module
658 will be called "whci-hcd".
Inaky Perez-Gonzalezd09318b2008-09-17 16:34:30 +0100659
660config USB_HWA_HCD
Greg Kroah-Hartmaneb83be92012-09-14 21:15:50 -0700661 tristate "Host Wire Adapter (HWA) driver"
Florian Fainelli25e11ec2013-04-09 14:29:25 +0200662 depends on UWB
Inaky Perez-Gonzalezd09318b2008-09-17 16:34:30 +0100663 select USB_WUSB
664 select UWB_HWA
665 help
666 This driver enables you to connect Wireless USB devices to
667 your system using a Host Wire Adaptor USB dongle. This is an
668 UWB Radio Controller and WUSB Host Controller connected to
669 your machine via USB (specified in WUSB1.0).
670
671 To compile this driver a module, choose M here: the module
672 will be called "hwa-hc".
Martin Fuzzey23d3e7a2009-11-21 12:14:48 +0100673
674config USB_IMX21_HCD
Sascha Hauer5de9ec42011-08-24 08:41:10 +0200675 tristate "i.MX21 HCD support"
Florian Fainelli25e11ec2013-04-09 14:29:25 +0200676 depends on ARM && ARCH_MXC
Martin Fuzzey23d3e7a2009-11-21 12:14:48 +0100677 help
678 This driver enables support for the on-chip USB host in the
Sascha Hauer5de9ec42011-08-24 08:41:10 +0200679 i.MX21 processor.
Martin Fuzzey23d3e7a2009-11-21 12:14:48 +0100680
681 To compile this driver as a module, choose M here: the
682 module will be called "imx21-hcd".
683
David Daney1643acc2010-10-08 14:47:52 -0700684
David Daney1643acc2010-10-08 14:47:52 -0700685
686config USB_OCTEON2_COMMON
687 bool
688 default y if USB_OCTEON_EHCI || USB_OCTEON_OHCI
Hauke Mehrtens62e11d12012-03-15 23:49:57 +0100689
690config USB_HCD_BCMA
691 tristate "BCMA usb host driver"
Greg Kroah-Hartmaneb83be92012-09-14 21:15:50 -0700692 depends on BCMA
Hauke Mehrtens62e11d12012-03-15 23:49:57 +0100693 select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
694 select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
695 help
Jesper Dangaard Brouer71c421d2012-06-15 12:01:33 +0200696 Enable support for the EHCI and OCHI host controller on an bcma bus.
Hauke Mehrtens62e11d12012-03-15 23:49:57 +0100697 It converts the bcma driver into two platform device drivers
698 for ehci and ohci.
699
700 If unsure, say N.
Hauke Mehrtens7043c2c2012-03-15 23:49:58 +0100701
702config USB_HCD_SSB
703 tristate "SSB usb host driver"
Greg Kroah-Hartmaneb83be92012-09-14 21:15:50 -0700704 depends on SSB
Hauke Mehrtens7043c2c2012-03-15 23:49:58 +0100705 select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
706 select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
707 help
Jesper Dangaard Brouer71c421d2012-06-15 12:01:33 +0200708 Enable support for the EHCI and OCHI host controller on an bcma bus.
Hauke Mehrtens7043c2c2012-03-15 23:49:58 +0100709 It converts the bcma driver into two platform device drivers
710 for ehci and ohci.
711
712 If unsure, say N.