drivers/clocksource/nomadik-mtu.c

/*
 * Copyright (C) 2008 STMicroelectronics
 * Copyright (C) 2010 Alessandro Rubini
 * Copyright (C) 2010 Linus Walleij for ST-Ericsson
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2, as
 * published by the Free Software Foundation.
 */
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/io.h>
#include <linux/clockchips.h>
#include <linux/clocksource.h>
#include <linux/clk.h>
#include <linux/jiffies.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/platform_data/clocksource-nomadik-mtu.h>
#include <asm/mach/time.h>
#include <asm/sched_clock.h>

/*
 * The MTU device hosts four different counters, with 4 set of
 * registers. These are register names.
 */

#define MTU_IMSC	0x00	/* Interrupt mask set/clear */
#define MTU_RIS		0x04	/* Raw interrupt status */
#define MTU_MIS		0x08	/* Masked interrupt status */
#define MTU_ICR		0x0C	/* Interrupt clear register */

/* per-timer registers take 0..3 as argument */
#define MTU_LR(x)	(0x10 + 0x10 * (x) + 0x00)	/* Load value */
#define MTU_VAL(x)	(0x10 + 0x10 * (x) + 0x04)	/* Current value */
#define MTU_CR(x)	(0x10 + 0x10 * (x) + 0x08)	/* Control reg */
#define MTU_BGLR(x)	(0x10 + 0x10 * (x) + 0x0c)	/* At next overflow */

/* bits for the control register */
#define MTU_CRn_ENA		0x80
#define MTU_CRn_PERIODIC	0x40	/* if 0 = free-running */
#define MTU_CRn_PRESCALE_MASK	0x0c
#define MTU_CRn_PRESCALE_1		0x00
#define MTU_CRn_PRESCALE_16		0x04
#define MTU_CRn_PRESCALE_256		0x08
#define MTU_CRn_32BITS		0x02
#define MTU_CRn_ONESHOT		0x01	/* if 0 = wraps reloading from BGLR*/

/* Other registers are usual amba/primecell registers, currently not used */
#define MTU_ITCR	0xff0
#define MTU_ITOP	0xff4

#define MTU_PERIPH_ID0	0xfe0
#define MTU_PERIPH_ID1	0xfe4
#define MTU_PERIPH_ID2	0xfe8
#define MTU_PERIPH_ID3	0xfeC

#define MTU_PCELL0	0xff0
#define MTU_PCELL1	0xff4
#define MTU_PCELL2	0xff8
#define MTU_PCELL3	0xffC

static void __iomem *mtu_base;
static bool clkevt_periodic;
static u32 clk_prescale;
static u32 nmdk_cycle;		/* write-once */
static struct delay_timer mtu_delay_timer;

#ifdef CONFIG_NOMADIK_MTU_SCHED_CLOCK
/*
 * Override the global weak sched_clock symbol with this
 * local implementation which uses the clocksource to get some
 * better resolution when scheduling the kernel.
 */
static u32 notrace nomadik_read_sched_clock(void)
{
	if (unlikely(!mtu_base))
		return 0;

	return -readl(mtu_base + MTU_VAL(0));
}
#endif

static unsigned long nmdk_timer_read_current_timer(void)
{
	return ~readl_relaxed(mtu_base + MTU_VAL(0));
}

/* Clockevent device: use one-shot mode */
static int nmdk_clkevt_next(unsigned long evt, struct clock_event_device *ev)
{
	writel(1 << 1, mtu_base + MTU_IMSC);
	writel(evt, mtu_base + MTU_LR(1));
	/* Load highest value, enable device, enable interrupts */
	writel(MTU_CRn_ONESHOT | clk_prescale |
	       MTU_CRn_32BITS | MTU_CRn_ENA,
	       mtu_base + MTU_CR(1));

	return 0;
}

void nmdk_clkevt_reset(void)
{
	if (clkevt_periodic) {
		/* Timer: configure load and background-load, and fire it up */
		writel(nmdk_cycle, mtu_base + MTU_LR(1));
		writel(nmdk_cycle, mtu_base + MTU_BGLR(1));

		writel(MTU_CRn_PERIODIC | clk_prescale |
		       MTU_CRn_32BITS | MTU_CRn_ENA,
		       mtu_base + MTU_CR(1));
		writel(1 << 1, mtu_base + MTU_IMSC);
	} else {
		/* Generate an interrupt to start the clockevent again */
		(void) nmdk_clkevt_next(nmdk_cycle, NULL);
	}
}

static void nmdk_clkevt_mode(enum clock_event_mode mode,
			     struct clock_event_device *dev)
{
	switch (mode) {
	case CLOCK_EVT_MODE_PERIODIC:
		clkevt_periodic = true;
		nmdk_clkevt_reset();
		break;
	case CLOCK_EVT_MODE_ONESHOT:
		clkevt_periodic = false;
		break;
	case CLOCK_EVT_MODE_SHUTDOWN:
	case CLOCK_EVT_MODE_UNUSED:
		writel(0, mtu_base + MTU_IMSC);
		/* disable timer */
		writel(0, mtu_base + MTU_CR(1));
		/* load some high default value */
		writel(0xffffffff, mtu_base + MTU_LR(1));
		break;
	case CLOCK_EVT_MODE_RESUME:
		break;
	}
}

static struct clock_event_device nmdk_clkevt = {
	.name		= "mtu_1",
	.features	= CLOCK_EVT_FEAT_ONESHOT | CLOCK_EVT_FEAT_PERIODIC,
	.rating		= 200,
	.set_mode	= nmdk_clkevt_mode,
	.set_next_event	= nmdk_clkevt_next,
};

/*
 * IRQ Handler for timer 1 of the MTU block.
 */
static irqreturn_t nmdk_timer_interrupt(int irq, void *dev_id)
{
	struct clock_event_device *evdev = dev_id;

	writel(1 << 1, mtu_base + MTU_ICR); /* Interrupt clear reg */
	evdev->event_handler(evdev);
	return IRQ_HANDLED;
}

static struct irqaction nmdk_timer_irq = {
	.name		= "Nomadik Timer Tick",
	.flags		= IRQF_DISABLED | IRQF_TIMER,
	.handler	= nmdk_timer_interrupt,
	.dev_id		= &nmdk_clkevt,
};

void nmdk_clksrc_reset(void)
{
	/* Disable */
	writel(0, mtu_base + MTU_CR(0));

	/* ClockSource: configure load and background-load, and fire it up */
	writel(nmdk_cycle, mtu_base + MTU_LR(0));
	writel(nmdk_cycle, mtu_base + MTU_BGLR(0));

	writel(clk_prescale | MTU_CRn_32BITS | MTU_CRn_ENA,
	       mtu_base + MTU_CR(0));
}

void __init nmdk_timer_init(void __iomem *base, int irq)
{
	unsigned long rate;
	struct clk *clk0, *pclk0;

	mtu_base = base;

	pclk0 = clk_get_sys("mtu0", "apb_pclk");
	BUG_ON(IS_ERR(pclk0));
	BUG_ON(clk_prepare(pclk0) < 0);
	BUG_ON(clk_enable(pclk0) < 0);

	clk0 = clk_get_sys("mtu0", NULL);
	BUG_ON(IS_ERR(clk0));
	BUG_ON(clk_prepare(clk0) < 0);
	BUG_ON(clk_enable(clk0) < 0);

	/*
	 * Tick rate is 2.4MHz for Nomadik and 2.4Mhz, 100MHz or 133 MHz
	 * for ux500.
	 * Use a divide-by-16 counter if the tick rate is more than 32MHz.
	 * At 32 MHz, the timer (with 32 bit counter) can be programmed
	 * to wake-up at a max 127s a head in time. Dividing a 2.4 MHz timer
	 * with 16 gives too low timer resolution.
	 */
	rate = clk_get_rate(clk0);
	if (rate > 32000000) {
		rate /= 16;
		clk_prescale = MTU_CRn_PRESCALE_16;
	} else {
		clk_prescale = MTU_CRn_PRESCALE_1;
	}

	/* Cycles for periodic mode */
	nmdk_cycle = DIV_ROUND_CLOSEST(rate, HZ);


	/* Timer 0 is the free running clocksource */
	nmdk_clksrc_reset();

	if (clocksource_mmio_init(mtu_base + MTU_VAL(0), "mtu_0",
			rate, 200, 32, clocksource_mmio_readl_down))
		pr_err("timer: failed to initialize clock source %s\n",
		       "mtu_0");

#ifdef CONFIG_NOMADIK_MTU_SCHED_CLOCK
	setup_sched_clock(nomadik_read_sched_clock, 32, rate);
#endif

	/* Timer 1 is used for events, register irq and clockevents */
	setup_irq(irq, &nmdk_timer_irq);
	nmdk_clkevt.cpumask = cpumask_of(0);
	clockevents_config_and_register(&nmdk_clkevt, rate, 2, 0xffffffffU);

	mtu_delay_timer.read_current_timer = &nmdk_timer_read_current_timer;
	mtu_delay_timer.freq = rate;
	register_current_timer_delay(&mtu_delay_timer);
}