| /* |
| * Copyright (c) 2015-2019, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| &cci { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| actuator0: qcom,actuator@0 { |
| cell-index = <0>; |
| reg = <0x0>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <0>; |
| // cam_vaf-supply = <&pm8953_l17>; |
| qcom,cam-vreg-name = "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <2850000>; |
| qcom,cam-vreg-max-voltage = <2850000>; |
| qcom,cam-vreg-op-mode = <80000>; |
| }; |
| |
| actuator1: qcom,actuator@1 { |
| cell-index = <1>; |
| reg = <0x1>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <1>; |
| cam_vaf-supply = <&pm8953_l17>; |
| qcom,cam-vreg-name = "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <2850000>; |
| qcom,cam-vreg-max-voltage = <2850000>; |
| qcom,cam-vreg-op-mode = <80000>; |
| }; |
| |
| eeprom0: qcom,eeprom@0 { |
| cell-index = <0>; |
| compatible = "qcom,eeprom"; |
| qcom,cci-master = <0>; |
| reg = <0x0>; |
| cam_vana-supply = <&pm8953_l22>; |
| cam_v_custom1-supply = <&pm8953_l2>; |
| qcom,cam-vreg-name = "cam_vana", "cam_v_custom1"; |
| qcom,cam-vreg-min-voltage = <2800000 1175000>; |
| qcom,cam-vreg-max-voltage = <2800000 1175000>; |
| qcom,cam-vreg-op-mode = <80000 105000>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_default &cam_sensor_rear_default>; |
| pinctrl-1 = <&cam_sensor_mclk0_sleep &cam_sensor_rear_sleep>; |
| gpios = <&tlmm 26 0>, |
| <&tlmm 40 0>, |
| <&tlmm 130 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-vio = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK0", |
| "CAM_RESET0", |
| "CAM_VIO"; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <0>; |
| status = "ok"; |
| clocks = <&clock_gcc clk_mclk0_clk_src>, |
| <&clock_gcc clk_gcc_camss_mclk0_clk>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| /*<2018/10/18-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][]Modified for new front camera device driver S5K4H7YX. */ |
| eeprom1: qcom,eeprom@1 { |
| cell-index = <1>; |
| compatible = "qcom,eeprom"; |
| qcom,cci-master = <1>; |
| reg = <0x1>; |
| |
| #if 0 |
| qcom,eeprom-name = "samsung_s5k4h7yx"; |
| qcom,slave-addr = <0x20>; |
| qcom,num-blocks = <2>; |
| |
| qcom,page0 = <1 0x0100 2 0x01 1 1>; |
| qcom,poll0 = <0 0x0 2 0x0 1 0>; |
| qcom,mem0 = <0 0x0 2 0x0 1 0>; |
| #endif |
| |
| /* cam_vio-supply = <&cam_vio_gpio_regulator>; */ /* IOVDD */ |
| cam_vana-supply = <&pm8953_l22>; /* AVDD */ |
| /* cam_vdig-supply = <&cam_front_dvdd_gpio_regulator>; */ /* DVDD */ |
| /* cam_vaf-supply = <&pm8953_l17>; */ /* AFVDD is not usage */ |
| qcom,cam-vreg-name = "cam_vana"; /* "cam_vio", "cam_vana", "cam_vdig"; */ |
| qcom,cam-vreg-min-voltage = <2800000>; |
| qcom,cam-vreg-max-voltage = <2800000>; |
| qcom,cam-vreg-op-mode = <80000>; |
| qcom,gpio-no-mux = <0>; |
| |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk1_default |
| &cam_sensor_front1_default |
| &cam_sensor_front1_vdig_default |
| &cam_sensor_front1_vio_default>; |
| pinctrl-1 = <&cam_sensor_mclk1_sleep |
| &cam_sensor_front1_sleep |
| &cam_sensor_front1_vdig_sleep |
| &cam_sensor_front1_vio_sleep>; |
| |
| /*<2018/11/14-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][]VOI control pin.PCBA EP0 is GPIO123;EP1 and above is GPIO130 */ |
| gpios = <&tlmm 27 0>, |
| <&tlmm 129 0>, |
| <&tlmm 46 0>, |
| #if 1 |
| <&tlmm 130 0>; |
| #else /* PCBA EP0 */ |
| <&tlmm 123 0>; |
| #endif |
| /*>2018/11/14-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][] */ |
| qcom,gpio-reset = <1>; |
| qcom,gpio-vdig = <2>; |
| qcom,gpio-vio = <3>; |
| qcom,gpio-req-tbl-num = <0 1 2 3>; |
| qcom,gpio-req-tbl-flags = <1 0 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK2", |
| "CAM_RESET2", |
| "CAM_VDIG2", |
| "CAM_VIO2"; |
| |
| status = "ok"; |
| #if 1 |
| qcom,cam-power-seq-val = "sensor_gpio_reset", |
| "cam_vana", "sensor_gpio_vdig", |
| "sensor_gpio_vio", "sensor_gpio_reset", |
| "sensor_cam_mclk"; |
| qcom,cam-power-seq-type = "sensor_gpio", |
| "sensor_vreg", "sensor_gpio", |
| "sensor_gpio", "sensor_gpio", |
| "sensor_clk"; |
| qcom,cam-power-seq-cfg-val = <0 1 1 1 1 24000000>; |
| qcom,cam-power-seq-delay = <5 1 1 3 3 10>; /* <1 1 1 1 1 10>; */ |
| #endif |
| clock-names = "cam_src_clk", "cam_clk"; |
| clocks = <&clock_gcc clk_mclk1_clk_src>, |
| <&clock_gcc clk_gcc_camss_mclk1_clk>; |
| qcom,clock-rates = <19200000 0>; |
| }; |
| /*>2018/10/18-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][]. */ |
| |
| camera0: qcom,camera@0 { |
| cell-index = <0>; |
| compatible = "qcom,camera"; |
| reg = <0x0>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,mount-angle = <270>; |
| qcom,led-flash-src = <&led_flash0>; |
| qcom,eeprom-src = <&eeprom0>; |
| qcom,actuator-src = <&actuator0>; |
| // cam_vio-supply = <&pm8953_l6>; |
| // cam_vdig-supply = <&pm8953_l2>; |
| // cam_vaf-supply = <&pm8953_l17>; |
| cam_vana-supply = <&pm8953_l22>; |
| cam_v_custom1-supply = <&pm8953_l2>; |
| qcom,cam-vreg-name = "cam_vana", "cam_v_custom1"; |
| qcom,cam-vreg-min-voltage = <2800000 1175000>; |
| qcom,cam-vreg-max-voltage = <2800000 1175000>; |
| qcom,cam-vreg-op-mode = <80000 105000>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_default |
| &cam_sensor_rear_default |
| &cam_sensor_rear_vana>; |
| pinctrl-1 = <&cam_sensor_mclk0_sleep &cam_sensor_rear_sleep |
| &cam_sensor_rear_vana_sleep>; |
| gpios = <&tlmm 26 0>, |
| <&tlmm 40 0>, |
| <&tlmm 130 0>, |
| <&tlmm 128 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-vio = <2>; |
| qcom,gpio-vaf = <3>; |
| qcom,gpio-req-tbl-num = <0 1 2 3>; |
| qcom,gpio-req-tbl-flags = <1 0 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK0", |
| "CAM_RESET0", |
| "CAM_VIO", |
| "CAM_VAF"; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| clocks = <&clock_gcc clk_mclk0_clk_src>, |
| <&clock_gcc clk_gcc_camss_mclk0_clk>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| /*<2018/10/18-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][]Modified for new front camera device driver S5K4H7YX. */ |
| camera2: qcom,camera@2 { |
| cell-index = <2>; |
| compatible = "qcom,camera"; |
| reg = <0x02>; |
| qcom,csiphy-sd-index = <2>; |
| qcom,csid-sd-index = <1>; /* SDM450 support 2 CSID cores. MSM8953 is 3 CSID cores */ |
| qcom,mount-angle = <270>; /* <90>; */ |
| qcom,eeprom-src = <&eeprom1>; |
| /* qcom,actuator-src = <&actuator1>; */ /* The auto focus is not support */ |
| |
| /* cam_vio-supply = <&cam_vio_gpio_regulator>; */ |
| cam_vana-supply = <&pm8953_l22>; |
| /* cam_vdig-supply = <&cam_front_dvdd_gpio_regulator>; */ |
| /* cam_vaf-supply = <&pm8953_l17>; */ /* The AFVDD is not support */ |
| qcom,cam-vreg-name = "cam_vana"; |
| qcom,cam-vreg-min-voltage = <2800000>; |
| qcom,cam-vreg-max-voltage = <2800000>; |
| qcom,cam-vreg-op-mode = <80000>; |
| qcom,gpio-no-mux = <0>; |
| |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk1_default |
| &cam_sensor_front1_default |
| &cam_sensor_front1_vdig_default |
| &cam_sensor_front1_vio_default>; |
| pinctrl-1 = <&cam_sensor_mclk1_sleep |
| &cam_sensor_front1_sleep |
| &cam_sensor_front1_vdig_sleep |
| &cam_sensor_front1_vio_sleep>; |
| |
| /*<2018/11/14-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][]VOI control pin.PCBA EP0 is GPIO123;EP1 and above is GPIO130 */ |
| gpios = <&tlmm 27 0>, |
| <&tlmm 129 0>, |
| <&tlmm 46 0>, |
| #if 1 |
| <&tlmm 130 0>; |
| #else /* PCBA EP0 */ |
| <&tlmm 123 0>; |
| #endif |
| /*>2018/11/14-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][] */ |
| qcom,gpio-reset = <1>; |
| qcom,gpio-vdig = <2>; |
| qcom,gpio-vio = <3>; |
| qcom,gpio-req-tbl-num = <0 1 2 3>; |
| qcom,gpio-req-tbl-flags = <1 0 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK2", |
| "CAM_RESET2", |
| "CAM_VDIG2", |
| "CAM_VIO2"; |
| |
| qcom,sensor-position = <1>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <1>; |
| status = "ok"; |
| clock-names = "cam_src_clk", "cam_clk"; |
| clocks = <&clock_gcc clk_mclk1_clk_src>, |
| <&clock_gcc clk_gcc_camss_mclk1_clk>; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| /*>2018/10/18-Yuting Shih.[FAIRPHONE][MISC][COMMON][CAMERA][][]. */ |
| }; |