Documentation/watchdog/watchdog-api.txt - kernel/msm-4.9 - Gitiles

 Last reviewed: 10/05/2007


 The Linux Watchdog driver API.

 Copyright 2002 Christer Weingel <wingel@nano-system.com>

 Some parts of this document are copied verbatim from the sbc60xxwdt
 driver which is (c) Copyright 2000 Jakob Oestergaard <jakob@ostenfeld.dk>

 This document describes the state of the Linux 2.4.18 kernel.

 Introduction:

 A Watchdog Timer (WDT) is a hardware circuit that can reset the
 computer system in case of a software fault.  You probably knew that
 already.

 Usually a userspace daemon will notify the kernel watchdog driver via the
 /dev/watchdog special device file that userspace is still alive, at
 regular intervals.  When such a notification occurs, the driver will
 usually tell the hardware watchdog that everything is in order, and
 that the watchdog should wait for yet another little while to reset
 the system.  If userspace fails (RAM error, kernel bug, whatever), the
 notifications cease to occur, and the hardware watchdog will reset the
 system (causing a reboot) after the timeout occurs.

 The Linux watchdog API is a rather ad-hoc construction and different
 drivers implement different, and sometimes incompatible, parts of it.
 This file is an attempt to document the existing usage and allow
 future driver writers to use it as a reference.

 The simplest API:

 All drivers support the basic mode of operation, where the watchdog
 activates as soon as /dev/watchdog is opened and will reboot unless
 the watchdog is pinged within a certain time, this time is called the
 timeout or margin.  The simplest way to ping the watchdog is to write
 some data to the device.  So a very simple watchdog daemon would look
 like this source file:  see Documentation/watchdog/src/watchdog-simple.c

 A more advanced driver could for example check that a HTTP server is
 still responding before doing the write call to ping the watchdog.

 When the device is closed, the watchdog is disabled, unless the "Magic
 Close" feature is supported (see below).  This is not always such a
 good idea, since if there is a bug in the watchdog daemon and it
 crashes the system will not reboot.  Because of this, some of the
 drivers support the configuration option "Disable watchdog shutdown on
 close", CONFIG_WATCHDOG_NOWAYOUT.  If it is set to Y when compiling
 the kernel, there is no way of disabling the watchdog once it has been
 started.  So, if the watchdog daemon crashes, the system will reboot
 after the timeout has passed. Watchdog devices also usually support
 the nowayout module parameter so that this option can be controlled at
 runtime.

 Magic Close feature:

 If a driver supports "Magic Close", the driver will not disable the
 watchdog unless a specific magic character 'V' has been sent to
 /dev/watchdog just before closing the file.  If the userspace daemon
 closes the file without sending this special character, the driver
 will assume that the daemon (and userspace in general) died, and will
 stop pinging the watchdog without disabling it first.  This will then
 cause a reboot if the watchdog is not re-opened in sufficient time.

 The ioctl API:

 All conforming drivers also support an ioctl API.

 Pinging the watchdog using an ioctl:

 All drivers that have an ioctl interface support at least one ioctl,
 KEEPALIVE.  This ioctl does exactly the same thing as a write to the
 watchdog device, so the main loop in the above program could be
 replaced with:

 	while (1) {
 		ioctl(fd, WDIOC_KEEPALIVE, 0);
 		sleep(10);
 	}

 the argument to the ioctl is ignored.

 Setting and getting the timeout:

 For some drivers it is possible to modify the watchdog timeout on the
 fly with the SETTIMEOUT ioctl, those drivers have the WDIOF_SETTIMEOUT
 flag set in their option field.  The argument is an integer
 representing the timeout in seconds.  The driver returns the real
 timeout used in the same variable, and this timeout might differ from
 the requested one due to limitation of the hardware.

     int timeout = 45;
     ioctl(fd, WDIOC_SETTIMEOUT, &timeout);
     printf("The timeout was set to %d seconds\n", timeout);

 This example might actually print "The timeout was set to 60 seconds"
 if the device has a granularity of minutes for its timeout.

 Starting with the Linux 2.4.18 kernel, it is possible to query the
 current timeout using the GETTIMEOUT ioctl.

     ioctl(fd, WDIOC_GETTIMEOUT, &timeout);
     printf("The timeout was is %d seconds\n", timeout);

 Pretimeouts:

 Some watchdog timers can be set to have a trigger go off before the
 actual time they will reset the system.  This can be done with an NMI,
 interrupt, or other mechanism.  This allows Linux to record useful
 information (like panic information and kernel coredumps) before it
 resets.

     pretimeout = 10;
     ioctl(fd, WDIOC_SETPRETIMEOUT, &pretimeout);

 Note that the pretimeout is the number of seconds before the time
 when the timeout will go off.  It is not the number of seconds until
 the pretimeout.  So, for instance, if you set the timeout to 60 seconds
 and the pretimeout to 10 seconds, the pretimout will go of in 50
 seconds.  Setting a pretimeout to zero disables it.

 There is also a get function for getting the pretimeout:

     ioctl(fd, WDIOC_GETPRETIMEOUT, &timeout);
     printf("The pretimeout was is %d seconds\n", timeout);

 Not all watchdog drivers will support a pretimeout.

 Get the number of seconds before reboot:

 Some watchdog drivers have the ability to report the remaining time
 before the system will reboot. The WDIOC_GETTIMELEFT is the ioctl
 that returns the number of seconds before reboot.

     ioctl(fd, WDIOC_GETTIMELEFT, &timeleft);
     printf("The timeout was is %d seconds\n", timeleft);

 Environmental monitoring:

 All watchdog drivers are required return more information about the system,
 some do temperature, fan and power level monitoring, some can tell you
 the reason for the last reboot of the system.  The GETSUPPORT ioctl is
 available to ask what the device can do:

 	struct watchdog_info ident;
 	ioctl(fd, WDIOC_GETSUPPORT, &ident);

 the fields returned in the ident struct are:

         identity		a string identifying the watchdog driver
 	firmware_version	the firmware version of the card if available
 	options			a flags describing what the device supports

 the options field can have the following bits set, and describes what
 kind of information that the GET_STATUS and GET_BOOT_STATUS ioctls can
 return.   [FIXME -- Is this correct?]

 	WDIOF_OVERHEAT		Reset due to CPU overheat

 The machine was last rebooted by the watchdog because the thermal limit was
 exceeded

 	WDIOF_FANFAULT		Fan failed

 A system fan monitored by the watchdog card has failed

 	WDIOF_EXTERN1		External relay 1

 External monitoring relay/source 1 was triggered. Controllers intended for
 real world applications include external monitoring pins that will trigger
 a reset.

 	WDIOF_EXTERN2		External relay 2

 External monitoring relay/source 2 was triggered

 	WDIOF_POWERUNDER	Power bad/power fault

 The machine is showing an undervoltage status

 	WDIOF_CARDRESET		Card previously reset the CPU

 The last reboot was caused by the watchdog card

 	WDIOF_POWEROVER		Power over voltage

 The machine is showing an overvoltage status. Note that if one level is
 under and one over both bits will be set - this may seem odd but makes
 sense.

 	WDIOF_KEEPALIVEPING	Keep alive ping reply

 The watchdog saw a keepalive ping since it was last queried.

 	WDIOF_SETTIMEOUT	Can set/get the timeout

 The watchdog can do pretimeouts.

 	WDIOF_PRETIMEOUT	Pretimeout (in seconds), get/set


 For those drivers that return any bits set in the option field, the
 GETSTATUS and GETBOOTSTATUS ioctls can be used to ask for the current
 status, and the status at the last reboot, respectively.

     int flags;
     ioctl(fd, WDIOC_GETSTATUS, &flags);

     or

     ioctl(fd, WDIOC_GETBOOTSTATUS, &flags);

 Note that not all devices support these two calls, and some only
 support the GETBOOTSTATUS call.

 Some drivers can measure the temperature using the GETTEMP ioctl.  The
 returned value is the temperature in degrees fahrenheit.

     int temperature;
     ioctl(fd, WDIOC_GETTEMP, &temperature);

 Finally the SETOPTIONS ioctl can be used to control some aspects of
 the cards operation; right now the pcwd driver is the only one
 supporting this ioctl.

     int options = 0;
     ioctl(fd, WDIOC_SETOPTIONS, options);

 The following options are available:

 	WDIOS_DISABLECARD	Turn off the watchdog timer
 	WDIOS_ENABLECARD	Turn on the watchdog timer
 	WDIOS_TEMPPANIC		Kernel panic on temperature trip

 [FIXME -- better explanations]
	Last reviewed: 10/05/2007


	The Linux Watchdog driver API.

	Copyright 2002 Christer Weingel <wingel@nano-system.com>

	Some parts of this document are copied verbatim from the sbc60xxwdt
	driver which is (c) Copyright 2000 Jakob Oestergaard <jakob@ostenfeld.dk>

	This document describes the state of the Linux 2.4.18 kernel.

	Introduction:

	A Watchdog Timer (WDT) is a hardware circuit that can reset the
	computer system in case of a software fault. You probably knew that
	already.

	Usually a userspace daemon will notify the kernel watchdog driver via the
	/dev/watchdog special device file that userspace is still alive, at
	regular intervals. When such a notification occurs, the driver will
	usually tell the hardware watchdog that everything is in order, and
	that the watchdog should wait for yet another little while to reset
	the system. If userspace fails (RAM error, kernel bug, whatever), the
	notifications cease to occur, and the hardware watchdog will reset the
	system (causing a reboot) after the timeout occurs.

	The Linux watchdog API is a rather ad-hoc construction and different
	drivers implement different, and sometimes incompatible, parts of it.
	This file is an attempt to document the existing usage and allow
	future driver writers to use it as a reference.

	The simplest API:

	All drivers support the basic mode of operation, where the watchdog
	activates as soon as /dev/watchdog is opened and will reboot unless
	the watchdog is pinged within a certain time, this time is called the
	timeout or margin. The simplest way to ping the watchdog is to write
	some data to the device. So a very simple watchdog daemon would look
	like this source file: see Documentation/watchdog/src/watchdog-simple.c

	A more advanced driver could for example check that a HTTP server is
	still responding before doing the write call to ping the watchdog.

	When the device is closed, the watchdog is disabled, unless the "Magic
	Close" feature is supported (see below). This is not always such a
	good idea, since if there is a bug in the watchdog daemon and it
	crashes the system will not reboot. Because of this, some of the
	drivers support the configuration option "Disable watchdog shutdown on
	close", CONFIG_WATCHDOG_NOWAYOUT. If it is set to Y when compiling
	the kernel, there is no way of disabling the watchdog once it has been
	started. So, if the watchdog daemon crashes, the system will reboot
	after the timeout has passed. Watchdog devices also usually support
	the nowayout module parameter so that this option can be controlled at
	runtime.

	Magic Close feature:

	If a driver supports "Magic Close", the driver will not disable the
	watchdog unless a specific magic character 'V' has been sent to
	/dev/watchdog just before closing the file. If the userspace daemon
	closes the file without sending this special character, the driver
	will assume that the daemon (and userspace in general) died, and will
	stop pinging the watchdog without disabling it first. This will then
	cause a reboot if the watchdog is not re-opened in sufficient time.

	The ioctl API:

	All conforming drivers also support an ioctl API.

	Pinging the watchdog using an ioctl:

	All drivers that have an ioctl interface support at least one ioctl,
	KEEPALIVE. This ioctl does exactly the same thing as a write to the
	watchdog device, so the main loop in the above program could be
	replaced with:

	while (1) {
	ioctl(fd, WDIOC_KEEPALIVE, 0);
	sleep(10);
	}

	the argument to the ioctl is ignored.

	Setting and getting the timeout:

	For some drivers it is possible to modify the watchdog timeout on the
	fly with the SETTIMEOUT ioctl, those drivers have the WDIOF_SETTIMEOUT
	flag set in their option field. The argument is an integer
	representing the timeout in seconds. The driver returns the real
	timeout used in the same variable, and this timeout might differ from
	the requested one due to limitation of the hardware.

	int timeout = 45;
	ioctl(fd, WDIOC_SETTIMEOUT, &timeout);
	printf("The timeout was set to %d seconds\n", timeout);

	This example might actually print "The timeout was set to 60 seconds"
	if the device has a granularity of minutes for its timeout.

	Starting with the Linux 2.4.18 kernel, it is possible to query the
	current timeout using the GETTIMEOUT ioctl.

	ioctl(fd, WDIOC_GETTIMEOUT, &timeout);
	printf("The timeout was is %d seconds\n", timeout);

	Pretimeouts:

	Some watchdog timers can be set to have a trigger go off before the
	actual time they will reset the system. This can be done with an NMI,
	interrupt, or other mechanism. This allows Linux to record useful
	information (like panic information and kernel coredumps) before it
	resets.

	pretimeout = 10;
	ioctl(fd, WDIOC_SETPRETIMEOUT, &pretimeout);

	Note that the pretimeout is the number of seconds before the time
	when the timeout will go off. It is not the number of seconds until
	the pretimeout. So, for instance, if you set the timeout to 60 seconds
	and the pretimeout to 10 seconds, the pretimout will go of in 50
	seconds. Setting a pretimeout to zero disables it.

	There is also a get function for getting the pretimeout:

	ioctl(fd, WDIOC_GETPRETIMEOUT, &timeout);
	printf("The pretimeout was is %d seconds\n", timeout);

	Not all watchdog drivers will support a pretimeout.

	Get the number of seconds before reboot:

	Some watchdog drivers have the ability to report the remaining time
	before the system will reboot. The WDIOC_GETTIMELEFT is the ioctl
	that returns the number of seconds before reboot.

	ioctl(fd, WDIOC_GETTIMELEFT, &timeleft);
	printf("The timeout was is %d seconds\n", timeleft);

	Environmental monitoring:

	All watchdog drivers are required return more information about the system,
	some do temperature, fan and power level monitoring, some can tell you
	the reason for the last reboot of the system. The GETSUPPORT ioctl is
	available to ask what the device can do:

	struct watchdog_info ident;
	ioctl(fd, WDIOC_GETSUPPORT, &ident);

	the fields returned in the ident struct are:

	identity a string identifying the watchdog driver
	firmware_version the firmware version of the card if available
	options a flags describing what the device supports

	the options field can have the following bits set, and describes what
	kind of information that the GET_STATUS and GET_BOOT_STATUS ioctls can
	return. [FIXME -- Is this correct?]

	WDIOF_OVERHEAT Reset due to CPU overheat

	The machine was last rebooted by the watchdog because the thermal limit was
	exceeded

	WDIOF_FANFAULT Fan failed

	A system fan monitored by the watchdog card has failed

	WDIOF_EXTERN1 External relay 1

	External monitoring relay/source 1 was triggered. Controllers intended for
	real world applications include external monitoring pins that will trigger
	a reset.

	WDIOF_EXTERN2 External relay 2

	External monitoring relay/source 2 was triggered

	WDIOF_POWERUNDER Power bad/power fault

	The machine is showing an undervoltage status

	WDIOF_CARDRESET Card previously reset the CPU

	The last reboot was caused by the watchdog card

	WDIOF_POWEROVER Power over voltage

	The machine is showing an overvoltage status. Note that if one level is
	under and one over both bits will be set - this may seem odd but makes
	sense.

	WDIOF_KEEPALIVEPING Keep alive ping reply

	The watchdog saw a keepalive ping since it was last queried.

	WDIOF_SETTIMEOUT Can set/get the timeout

	The watchdog can do pretimeouts.

	WDIOF_PRETIMEOUT Pretimeout (in seconds), get/set


	For those drivers that return any bits set in the option field, the
	GETSTATUS and GETBOOTSTATUS ioctls can be used to ask for the current
	status, and the status at the last reboot, respectively.

	int flags;
	ioctl(fd, WDIOC_GETSTATUS, &flags);

	or

	ioctl(fd, WDIOC_GETBOOTSTATUS, &flags);

	Note that not all devices support these two calls, and some only
	support the GETBOOTSTATUS call.

	Some drivers can measure the temperature using the GETTEMP ioctl. The
	returned value is the temperature in degrees fahrenheit.

	int temperature;
	ioctl(fd, WDIOC_GETTEMP, &temperature);

	Finally the SETOPTIONS ioctl can be used to control some aspects of
	the cards operation; right now the pcwd driver is the only one
	supporting this ioctl.

	int options = 0;
	ioctl(fd, WDIOC_SETOPTIONS, options);

	The following options are available:

	WDIOS_DISABLECARD Turn off the watchdog timer
	WDIOS_ENABLECARD Turn on the watchdog timer
	WDIOS_TEMPPANIC Kernel panic on temperature trip

	[FIXME -- better explanations]