Merge tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch
of long-standing bugs in the tty layer and serial drivers as normal.
Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
MAINTAINERS: 8250: remove website reference
serial: core: Fix port mutex assert if lockdep disabled
serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
tty: vt, finish looping on duplicate
tty: vt, return error when con_startup fails
QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
serial: 8250dw: Add device HID for future AMD UART controller
Fix OpenSSH pty regression on close
serial: mctrl_gpio: add IRQ locking
serial: 8250: Integrate Fintek into 8250_base
serial: mps2-uart: add support for early console
serial: mps2-uart: add MPS2 UART driver
dt-bindings: document the MPS2 UART bindings
serial: sirf: Use generic uart-has-rtscts DT property
serial: sirf: Introduce helper variable struct device_node *np
serial: mxs-auart: Use generic uart-has-rtscts DT property
serial: imx: Use generic uart-has-rtscts DT property
doc: DT: Add Generic Serial Device Tree Bindings
serial: 8250: of: Make tegra_serial_handle_break() static
...
diff --git a/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt b/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt
new file mode 100644
index 0000000..128cc6a
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/arm,mps2-uart.txt
@@ -0,0 +1,19 @@
+ARM MPS2 UART
+
+Required properties:
+- compatible : Should be "arm,mps2-uart"
+- reg : Address and length of the register set
+- interrupts : Reference to the UART RX, TX and overrun interrupts
+
+Required clocking property:
+- clocks : The input clock of the UART
+
+
+Examples:
+
+uart0: serial@40004000 {
+ compatible = "arm,mps2-uart";
+ reg = <0x40004000 0x1000>;
+ interrupts = <0 1 12>;
+ clocks = <&sysclk>;
+};
diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
index ed94c21..1e82802 100644
--- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
+++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
@@ -6,7 +6,7 @@
- interrupts : Should contain uart interrupt
Optional properties:
-- fsl,uart-has-rtscts : Indicate the uart has rts and cts
+- uart-has-rtscts : Indicate the uart has rts and cts
- fsl,irda-mode : Indicate the uart supports irda mode
- fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
in DCE mode by default.
@@ -24,6 +24,6 @@
compatible = "fsl,imx51-uart", "fsl,imx21-uart";
reg = <0x73fbc000 0x4000>;
interrupts = <31>;
- fsl,uart-has-rtscts;
+ uart-has-rtscts;
fsl,dte-mode;
};
diff --git a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt
index 7c408c8..5c96d41 100644
--- a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt
+++ b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt
@@ -1,8 +1,10 @@
* Freescale MXS Application UART (AUART)
-Required properties:
-- compatible : Should be "fsl,<soc>-auart". The supported SoCs include
- imx23 and imx28.
+Required properties for all SoCs:
+- compatible : Should be one of fallowing variants:
+ "fsl,imx23-auart" - Freescale i.MX23
+ "fsl,imx28-auart" - Freescale i.MX28
+ "alphascale,asm9260-auart" - Alphascale ASM9260
- reg : Address and length of the register set for the device
- interrupts : Should contain the auart interrupt numbers
- dmas: DMA specifier, consisting of a phandle to DMA controller node
@@ -10,8 +12,14 @@
Refer to dma.txt and fsl-mxs-dma.txt for details.
- dma-names: "rx" for RX channel, "tx" for TX channel.
+Required properties for "alphascale,asm9260-auart":
+- clocks : the clocks feeding the watchdog timer. See clock-bindings.txt
+- clock-names : should be set to
+ "mod" - source for tick counter.
+ "ahb" - ahb gate.
+
Optional properties:
-- fsl,uart-has-rtscts : Indicate the UART has RTS and CTS lines
+- uart-has-rtscts : Indicate the UART has RTS and CTS lines
for hardware flow control,
it also means you enable the DMA support for this UART.
- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD
diff --git a/Documentation/devicetree/bindings/serial/serial.txt b/Documentation/devicetree/bindings/serial/serial.txt
new file mode 100644
index 0000000..fd970f7
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/serial.txt
@@ -0,0 +1,57 @@
+Generic Serial DT Bindings
+
+This document lists a set of generic properties for describing UARTs in a
+device tree. Whether these properties apply to a particular device depends on
+the DT bindings for the actual device.
+
+Optional properties:
+ - cts-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
+ used as the UART's CTS line.
+ - dcd-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
+ used as the UART's DCD line.
+ - dsr-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
+ used as the UART's DSR line.
+ - dtr-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
+ used as the UART's DTR line.
+ - rng-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
+ used as the UART's RNG line.
+ - rts-gpios: Must contain a GPIO specifier, referring to the GPIO pin to be
+ used as the UART's RTS line.
+
+ - uart-has-rtscts: The presence of this property indicates that the
+ UART has dedicated lines for RTS/CTS hardware flow control, and that
+ they are available for use (wired and enabled by pinmux configuration).
+ This depends on both the UART hardware and the board wiring.
+ Note that this property is mutually-exclusive with "cts-gpios" and
+ "rts-gpios" above.
+
+
+Examples:
+
+ uart1: serial@48022000 {
+ compatible = "ti,am3352-uart", "ti,omap3-uart";
+ ti,hwmods = "uart2";
+ clock-frequency = <48000000>;
+ reg = <0x48022000 0x2000>;
+ interrupts = <73>;
+ dmas = <&edma 28 0>, <&edma 29 0>;
+ dma-names = "tx", "rx";
+ dtr-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
+ dsr-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+ dcd-gpios = <&gpio2 24 GPIO_ACTIVE_LOW>;
+ rng-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>;
+ cts-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+ rts-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+ status = "okay";
+ };
+
+ scifa4: serial@e6c80000 {
+ compatible = "renesas,scifa-sh73a0", "renesas,scifa";
+ reg = <0xe6c80000 0x100>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp2_clks SH73A0_CLK_SCIFA4>;
+ clock-names = "fck";
+ power-domains = <&pd_a3sp>;
+ uart-has-rtscts;
+ status = "okay";
+ };
diff --git a/Documentation/devicetree/bindings/serial/sirf-uart.txt b/Documentation/devicetree/bindings/serial/sirf-uart.txt
index 67e2a0a..1e48bbb 100644
--- a/Documentation/devicetree/bindings/serial/sirf-uart.txt
+++ b/Documentation/devicetree/bindings/serial/sirf-uart.txt
@@ -9,9 +9,9 @@
- clocks : Should contain uart clock number
Optional properties:
-- sirf,uart-has-rtscts: we have hardware flow controller pins in hardware
-- rts-gpios: RTS pin for USP-based UART if sirf,uart-has-rtscts is true
-- cts-gpios: CTS pin for USP-based UART if sirf,uart-has-rtscts is true
+- uart-has-rtscts: we have hardware flow controller pins in hardware
+- rts-gpios: RTS pin for USP-based UART if uart-has-rtscts is true
+- cts-gpios: CTS pin for USP-based UART if uart-has-rtscts is true
Example:
@@ -28,7 +28,7 @@
usp@b0090000 {
compatible = "sirf,prima2-usp-uart";
- sirf,uart-has-rtscts;
+ uart-has-rtscts;
rts-gpios = <&gpio 15 0>;
cts-gpios = <&gpio 46 0>;
};
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 4e76a34..82b42c9 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -1054,6 +1054,12 @@
the driver will use only 32-bit accessors to read/write
the device registers.
+ meson,<addr>
+ Start an early, polled-mode console on a meson serial
+ port at the specified address. The serial port must
+ already be setup and configured. Options are not yet
+ supported.
+
msm_serial,<addr>
Start an early, polled-mode console on an msm serial
port at the specified address. The serial port
diff --git a/Documentation/serial/tty.txt b/Documentation/serial/tty.txt
index 798cba8..b487809 100644
--- a/Documentation/serial/tty.txt
+++ b/Documentation/serial/tty.txt
@@ -210,9 +210,6 @@
TTY_OTHER_CLOSED Device is a pty and the other side has closed.
-TTY_OTHER_DONE Device is a pty and the other side has closed and
- all pending input processing has been completed.
-
TTY_NO_WRITE_SPLIT Prevent driver from splitting up writes into
smaller chunks.
diff --git a/MAINTAINERS b/MAINTAINERS
index e840831..832f070 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -175,7 +175,6 @@
8250/16?50 (AND CLONE UARTS) SERIAL DRIVER
M: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
L: linux-serial@vger.kernel.org
-W: http://serial.sourceforge.net
S: Maintained
T: git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git
F: drivers/tty/serial/8250*
diff --git a/arch/ia64/hp/sim/simserial.c b/arch/ia64/hp/sim/simserial.c
index e70cade..21fd50d 100644
--- a/arch/ia64/hp/sim/simserial.c
+++ b/arch/ia64/hp/sim/simserial.c
@@ -300,7 +300,7 @@
if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
(cmd != TIOCSERCONFIG) && (cmd != TIOCSERGSTRUCT) &&
(cmd != TIOCMIWAIT)) {
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
}
diff --git a/arch/mips/ath79/early_printk.c b/arch/mips/ath79/early_printk.c
index b955faf..d1adc59 100644
--- a/arch/mips/ath79/early_printk.c
+++ b/arch/mips/ath79/early_printk.c
@@ -31,13 +31,15 @@
} while (1);
}
+#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
+
static void prom_putchar_ar71xx(unsigned char ch)
{
void __iomem *base = (void __iomem *)(KSEG1ADDR(AR71XX_UART_BASE));
- prom_putchar_wait(base + UART_LSR * 4, UART_LSR_THRE, UART_LSR_THRE);
+ prom_putchar_wait(base + UART_LSR * 4, BOTH_EMPTY, BOTH_EMPTY);
__raw_writel(ch, base + UART_TX * 4);
- prom_putchar_wait(base + UART_LSR * 4, UART_LSR_THRE, UART_LSR_THRE);
+ prom_putchar_wait(base + UART_LSR * 4, BOTH_EMPTY, BOTH_EMPTY);
}
static void prom_putchar_ar933x(unsigned char ch)
diff --git a/drivers/char/pcmcia/synclink_cs.c b/drivers/char/pcmcia/synclink_cs.c
index e524e83..d28922d 100644
--- a/drivers/char/pcmcia/synclink_cs.c
+++ b/drivers/char/pcmcia/synclink_cs.c
@@ -1101,7 +1101,7 @@
wake_up_interruptible(&info->status_event_wait_q);
wake_up_interruptible(&info->event_wait_q);
- if (info->port.flags & ASYNC_CHECK_CD) {
+ if (tty_port_check_carrier(&info->port)) {
if (debug_level >= DEBUG_LEVEL_ISR)
printk("%s CD now %s...", info->device_name,
(info->serial_signals & SerialSignal_DCD) ? "on" : "off");
@@ -1272,7 +1272,7 @@
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):startup(%s)\n", __FILE__, __LINE__, info->device_name);
- if (info->port.flags & ASYNC_INITIALIZED)
+ if (tty_port_initialized(&info->port))
return 0;
if (!info->tx_buf) {
@@ -1311,7 +1311,7 @@
if (tty)
clear_bit(TTY_IO_ERROR, &tty->flags);
- info->port.flags |= ASYNC_INITIALIZED;
+ tty_port_set_initialized(&info->port, 1);
return 0;
}
@@ -1322,7 +1322,7 @@
{
unsigned long flags;
- if (!(info->port.flags & ASYNC_INITIALIZED))
+ if (!tty_port_initialized(&info->port))
return;
if (debug_level >= DEBUG_LEVEL_INFO)
@@ -1361,7 +1361,7 @@
if (tty)
set_bit(TTY_IO_ERROR, &tty->flags);
- info->port.flags &= ~ASYNC_INITIALIZED;
+ tty_port_set_initialized(&info->port, 0);
}
static void mgslpc_program_hw(MGSLPC_INFO *info, struct tty_struct *tty)
@@ -1466,15 +1466,8 @@
}
info->timeout += HZ/50; /* Add .02 seconds of slop */
- if (cflag & CRTSCTS)
- info->port.flags |= ASYNC_CTS_FLOW;
- else
- info->port.flags &= ~ASYNC_CTS_FLOW;
-
- if (cflag & CLOCAL)
- info->port.flags &= ~ASYNC_CHECK_CD;
- else
- info->port.flags |= ASYNC_CHECK_CD;
+ tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
+ tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
/* process tty input control flags */
@@ -2246,7 +2239,7 @@
if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
(cmd != TIOCMIWAIT)) {
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
}
@@ -2316,7 +2309,7 @@
/* Handle transition away from B0 status */
if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) {
info->serial_signals |= SerialSignal_DTR;
- if (!C_CRTSCTS(tty) || !test_bit(TTY_THROTTLED, &tty->flags))
+ if (!C_CRTSCTS(tty) || !tty_throttled(tty))
info->serial_signals |= SerialSignal_RTS;
spin_lock_irqsave(&info->lock, flags);
set_signals(info);
@@ -2345,7 +2338,7 @@
if (tty_port_close_start(port, tty, filp) == 0)
goto cleanup;
- if (port->flags & ASYNC_INITIALIZED)
+ if (tty_port_initialized(port))
mgslpc_wait_until_sent(tty, info->timeout);
mgslpc_flush_buffer(tty);
@@ -2378,7 +2371,7 @@
if (mgslpc_paranoia_check(info, tty->name, "mgslpc_wait_until_sent"))
return;
- if (!(info->port.flags & ASYNC_INITIALIZED))
+ if (!tty_port_initialized(&info->port))
goto exit;
orig_jiffies = jiffies;
diff --git a/drivers/ipack/devices/ipoctal.c b/drivers/ipack/devices/ipoctal.c
index 035d544..75dd15d 100644
--- a/drivers/ipack/devices/ipoctal.c
+++ b/drivers/ipack/devices/ipoctal.c
@@ -629,8 +629,7 @@
tty_port_hangup(&channel->tty_port);
ipoctal_reset_channel(channel);
-
- clear_bit(ASYNCB_INITIALIZED, &channel->tty_port.flags);
+ tty_port_set_initialized(&channel->tty_port, 0);
wake_up_interruptible(&channel->tty_port.open_wait);
}
@@ -642,7 +641,7 @@
return;
ipoctal_reset_channel(channel);
- clear_bit(ASYNCB_INITIALIZED, &channel->tty_port.flags);
+ tty_port_set_initialized(&channel->tty_port, 0);
}
static void ipoctal_cleanup(struct tty_struct *tty)
diff --git a/drivers/isdn/i4l/isdn_tty.c b/drivers/isdn/i4l/isdn_tty.c
index 947d5c9..63eaa0a 100644
--- a/drivers/isdn/i4l/isdn_tty.c
+++ b/drivers/isdn/i4l/isdn_tty.c
@@ -1043,17 +1043,13 @@
if (!(cflag & PARODD))
cval |= UART_LCR_EPAR;
- if (cflag & CLOCAL)
- port->flags &= ~ASYNC_CHECK_CD;
- else {
- port->flags |= ASYNC_CHECK_CD;
- }
+ tty_port_set_check_carrier(port, ~cflag & CLOCAL);
}
static int
isdn_tty_startup(modem_info *info)
{
- if (info->port.flags & ASYNC_INITIALIZED)
+ if (tty_port_initialized(&info->port))
return 0;
isdn_lock_drivers();
#ifdef ISDN_DEBUG_MODEM_OPEN
@@ -1070,7 +1066,7 @@
*/
isdn_tty_change_speed(info);
- info->port.flags |= ASYNC_INITIALIZED;
+ tty_port_set_initialized(&info->port, 1);
info->msr |= (UART_MSR_DSR | UART_MSR_CTS);
info->send_outstanding = 0;
return 0;
@@ -1083,7 +1079,7 @@
static void
isdn_tty_shutdown(modem_info *info)
{
- if (!(info->port.flags & ASYNC_INITIALIZED))
+ if (!tty_port_initialized(&info->port))
return;
#ifdef ISDN_DEBUG_MODEM_OPEN
printk(KERN_DEBUG "Shutting down isdnmodem port %d ....\n", info->line);
@@ -1103,7 +1099,7 @@
if (info->port.tty)
set_bit(TTY_IO_ERROR, &info->port.tty->flags);
- info->port.flags &= ~ASYNC_INITIALIZED;
+ tty_port_set_initialized(&info->port, 0);
}
/* isdn_tty_write() is the main send-routine. It is called from the upper
@@ -1351,7 +1347,7 @@
if (isdn_tty_paranoia_check(info, tty->name, __func__))
return -ENODEV;
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
mutex_lock(&modem_info_mutex);
@@ -1378,7 +1374,7 @@
if (isdn_tty_paranoia_check(info, tty->name, __func__))
return -ENODEV;
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
#ifdef ISDN_DEBUG_MODEM_IOCTL
@@ -1419,7 +1415,7 @@
if (isdn_tty_paranoia_check(info, tty->name, "isdn_tty_ioctl"))
return -ENODEV;
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
switch (cmd) {
case TCSBRK: /* SVID version: non-zero arg --> no break */
@@ -1581,7 +1577,7 @@
* interrupt driver to stop checking the data ready bit in the
* line status register.
*/
- if (port->flags & ASYNC_INITIALIZED) {
+ if (tty_port_initialized(port)) {
tty_wait_until_sent(tty, 3000); /* 30 seconds timeout */
/*
* Before we drop DTR, make sure the UART transmitter
@@ -1622,7 +1618,7 @@
return;
isdn_tty_shutdown(info);
port->count = 0;
- port->flags &= ~ASYNC_NORMAL_ACTIVE;
+ tty_port_set_active(port, 0);
port->tty = NULL;
wake_up_interruptible(&port->open_wait);
}
@@ -1979,7 +1975,7 @@
#endif
if (
#ifndef FIX_FILE_TRANSFER
- (info->port.flags & ASYNC_NORMAL_ACTIVE) &&
+ tty_port_active(&info->port) &&
#endif
(info->isdn_driver == -1) &&
(info->isdn_channel == -1) &&
@@ -2018,8 +2014,6 @@
return (wret == 2) ? 3 : 0;
}
-#define TTY_IS_ACTIVE(info) (info->port.flags & ASYNC_NORMAL_ACTIVE)
-
int
isdn_tty_stat_callback(int i, isdn_ctrl *c)
{
@@ -2077,7 +2071,7 @@
#ifdef ISDN_TTY_STAT_DEBUG
printk(KERN_DEBUG "tty_STAT_DCONN ttyI%d\n", info->line);
#endif
- if (TTY_IS_ACTIVE(info)) {
+ if (tty_port_active(&info->port)) {
if (info->dialing == 1) {
info->dialing = 2;
return 1;
@@ -2088,7 +2082,7 @@
#ifdef ISDN_TTY_STAT_DEBUG
printk(KERN_DEBUG "tty_STAT_DHUP ttyI%d\n", info->line);
#endif
- if (TTY_IS_ACTIVE(info)) {
+ if (tty_port_active(&info->port)) {
if (info->dialing == 1)
isdn_tty_modem_result(RESULT_BUSY, info);
if (info->dialing > 1)
@@ -2118,7 +2112,7 @@
* waiting for it and
* set DCD-bit of its modem-status.
*/
- if (TTY_IS_ACTIVE(info) ||
+ if (tty_port_active(&info->port) ||
(info->port.blocked_open &&
(info->emu.mdmreg[REG_DCD] & BIT_DCD))) {
info->msr |= UART_MSR_DCD;
@@ -2145,7 +2139,7 @@
#ifdef ISDN_TTY_STAT_DEBUG
printk(KERN_DEBUG "tty_STAT_BHUP ttyI%d\n", info->line);
#endif
- if (TTY_IS_ACTIVE(info)) {
+ if (tty_port_active(&info->port)) {
#ifdef ISDN_DEBUG_MODEM_HUP
printk(KERN_DEBUG "Mhup in ISDN_STAT_BHUP\n");
#endif
@@ -2157,7 +2151,7 @@
#ifdef ISDN_TTY_STAT_DEBUG
printk(KERN_DEBUG "tty_STAT_NODCH ttyI%d\n", info->line);
#endif
- if (TTY_IS_ACTIVE(info)) {
+ if (tty_port_active(&info->port)) {
if (info->dialing) {
info->dialing = 0;
info->last_l2 = -1;
@@ -2183,14 +2177,14 @@
return 1;
#ifdef CONFIG_ISDN_TTY_FAX
case ISDN_STAT_FAXIND:
- if (TTY_IS_ACTIVE(info)) {
+ if (tty_port_active(&info->port)) {
isdn_tty_fax_command(info, c);
}
break;
#endif
#ifdef CONFIG_ISDN_AUDIO
case ISDN_STAT_AUDIO:
- if (TTY_IS_ACTIVE(info)) {
+ if (tty_port_active(&info->port)) {
switch (c->parm.num[0]) {
case ISDN_AUDIO_DTMF:
if (info->vonline) {
@@ -2528,7 +2522,7 @@
if (info->closing || (!info->port.tty))
return;
- if (info->port.flags & ASYNC_CHECK_CD)
+ if (tty_port_check_carrier(&info->port))
tty_hangup(info->port.tty);
}
}
diff --git a/drivers/mmc/card/sdio_uart.c b/drivers/mmc/card/sdio_uart.c
index 5415056..5af6fb9 100644
--- a/drivers/mmc/card/sdio_uart.c
+++ b/drivers/mmc/card/sdio_uart.c
@@ -895,7 +895,7 @@
/* Handle transition away from B0 status */
if (!(old_termios->c_cflag & CBAUD) && (cflag & CBAUD)) {
unsigned int mask = TIOCM_DTR;
- if (!(cflag & CRTSCTS) || !test_bit(TTY_THROTTLED, &tty->flags))
+ if (!(cflag & CRTSCTS) || !tty_throttled(tty))
mask |= TIOCM_RTS;
sdio_uart_set_mctrl(port, mask);
}
diff --git a/drivers/net/usb/hso.c b/drivers/net/usb/hso.c
index 111d907..4b44586 100644
--- a/drivers/net/usb/hso.c
+++ b/drivers/net/usb/hso.c
@@ -2029,7 +2029,7 @@
tty = tty_port_tty_get(&serial->port);
- if (tty && test_bit(TTY_THROTTLED, &tty->flags)) {
+ if (tty && tty_throttled(tty)) {
tty_kref_put(tty);
return -1;
}
diff --git a/drivers/s390/char/con3215.c b/drivers/s390/char/con3215.c
index e7e078b..931d10e 100644
--- a/drivers/s390/char/con3215.c
+++ b/drivers/s390/char/con3215.c
@@ -289,7 +289,7 @@
spin_lock_irqsave(get_ccwdev_lock(raw->cdev), flags);
raw->flags &= ~RAW3215_TIMER_RUNS;
- if (!(raw->port.flags & ASYNC_SUSPENDED)) {
+ if (!tty_port_suspended(&raw->port)) {
raw3215_mk_write_req(raw);
raw3215_start_io(raw);
if ((raw->queued_read || raw->queued_write) &&
@@ -311,8 +311,7 @@
*/
static inline void raw3215_try_io(struct raw3215_info *raw)
{
- if (!(raw->port.flags & ASYNC_INITIALIZED) ||
- (raw->port.flags & ASYNC_SUSPENDED))
+ if (!tty_port_initialized(&raw->port) || tty_port_suspended(&raw->port))
return;
if (raw->queued_read != NULL)
raw3215_start_io(raw);
@@ -494,7 +493,7 @@
/* While console is frozen for suspend we have no other
* choice but to drop message from the buffer to make
* room for even more messages. */
- if (raw->port.flags & ASYNC_SUSPENDED) {
+ if (tty_port_suspended(&raw->port)) {
raw3215_drop_line(raw);
continue;
}
@@ -616,10 +615,10 @@
{
unsigned long flags;
- if (raw->port.flags & ASYNC_INITIALIZED)
+ if (tty_port_initialized(&raw->port))
return 0;
raw->line_pos = 0;
- raw->port.flags |= ASYNC_INITIALIZED;
+ tty_port_set_initialized(&raw->port, 1);
spin_lock_irqsave(get_ccwdev_lock(raw->cdev), flags);
raw3215_try_io(raw);
spin_unlock_irqrestore(get_ccwdev_lock(raw->cdev), flags);
@@ -635,8 +634,7 @@
DECLARE_WAITQUEUE(wait, current);
unsigned long flags;
- if (!(raw->port.flags & ASYNC_INITIALIZED) ||
- (raw->flags & RAW3215_FIXED))
+ if (!tty_port_initialized(&raw->port) || (raw->flags & RAW3215_FIXED))
return;
/* Wait for outstanding requests, then free irq */
spin_lock_irqsave(get_ccwdev_lock(raw->cdev), flags);
@@ -650,7 +648,7 @@
spin_lock_irqsave(get_ccwdev_lock(raw->cdev), flags);
remove_wait_queue(&raw->empty_wait, &wait);
set_current_state(TASK_RUNNING);
- raw->port.flags &= ~ASYNC_INITIALIZED;
+ tty_port_set_initialized(&raw->port, 1);
}
spin_unlock_irqrestore(get_ccwdev_lock(raw->cdev), flags);
}
@@ -773,7 +771,7 @@
raw = dev_get_drvdata(&cdev->dev);
spin_lock_irqsave(get_ccwdev_lock(raw->cdev), flags);
raw3215_make_room(raw, RAW3215_BUFFER_SIZE);
- raw->port.flags |= ASYNC_SUSPENDED;
+ tty_port_set_suspended(&raw->port, 1);
spin_unlock_irqrestore(get_ccwdev_lock(raw->cdev), flags);
return 0;
}
@@ -786,7 +784,7 @@
/* Allow I/O again and flush output buffer. */
raw = dev_get_drvdata(&cdev->dev);
spin_lock_irqsave(get_ccwdev_lock(raw->cdev), flags);
- raw->port.flags &= ~ASYNC_SUSPENDED;
+ tty_port_set_suspended(&raw->port, 0);
raw->flags |= RAW3215_FLUSHING;
raw3215_try_io(raw);
raw->flags &= ~RAW3215_FLUSHING;
@@ -859,7 +857,7 @@
unsigned long flags;
raw = raw3215[0]; /* console 3215 is the first one */
- if (raw->port.flags & ASYNC_SUSPENDED)
+ if (tty_port_suspended(&raw->port))
/* The console is still frozen for suspend. */
if (ccw_device_force_console(raw->cdev))
/* Forcing didn't work, no panic message .. */
diff --git a/drivers/s390/char/tty3270.c b/drivers/s390/char/tty3270.c
index 0a9f219..272cb6c 100644
--- a/drivers/s390/char/tty3270.c
+++ b/drivers/s390/char/tty3270.c
@@ -1860,7 +1860,7 @@
tp = tty->driver_data;
if (!tp)
return -ENODEV;
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
return kbd_ioctl(tp->kbd, cmd, arg);
}
@@ -1874,7 +1874,7 @@
tp = tty->driver_data;
if (!tp)
return -ENODEV;
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
return kbd_ioctl(tp->kbd, cmd, (unsigned long)compat_ptr(arg));
}
diff --git a/drivers/staging/dgnc/dgnc_tty.c b/drivers/staging/dgnc/dgnc_tty.c
index bcd2bdf..5c22159 100644
--- a/drivers/staging/dgnc/dgnc_tty.c
+++ b/drivers/staging/dgnc/dgnc_tty.c
@@ -1255,7 +1255,7 @@
if (file->f_flags & O_NONBLOCK)
break;
- if (tty->flags & (1 << TTY_IO_ERROR)) {
+ if (tty_io_error(tty)) {
retval = -EIO;
break;
}
diff --git a/drivers/staging/fwserial/fwserial.c b/drivers/staging/fwserial/fwserial.c
index 9b23b5c..1f9389d 100644
--- a/drivers/staging/fwserial/fwserial.c
+++ b/drivers/staging/fwserial/fwserial.c
@@ -1305,7 +1305,7 @@
if ((baud == 0) && (old->c_cflag & CBAUD)) {
port->mctrl &= ~(TIOCM_DTR | TIOCM_RTS);
} else if ((baud != 0) && !(old->c_cflag & CBAUD)) {
- if (C_CRTSCTS(tty) || !test_bit(TTY_THROTTLED, &tty->flags))
+ if (C_CRTSCTS(tty) || !tty_throttled(tty))
port->mctrl |= TIOCM_DTR | TIOCM_RTS;
else
port->mctrl |= TIOCM_DTR;
diff --git a/drivers/staging/speakup/selection.c b/drivers/staging/speakup/selection.c
index 41ef099..0149edc 100644
--- a/drivers/staging/speakup/selection.c
+++ b/drivers/staging/speakup/selection.c
@@ -150,7 +150,7 @@
add_wait_queue(&vc->paste_wait, &wait);
while (sel_buffer && sel_buffer_lth > pasted) {
set_current_state(TASK_INTERRUPTIBLE);
- if (test_bit(TTY_THROTTLED, &tty->flags)) {
+ if (tty_throttled(tty)) {
schedule();
continue;
}
diff --git a/drivers/tty/amiserial.c b/drivers/tty/amiserial.c
index eacf4c9..208f573 100644
--- a/drivers/tty/amiserial.c
+++ b/drivers/tty/amiserial.c
@@ -398,7 +398,7 @@
wake_up_interruptible(&port->delta_msr_wait);
}
- if ((port->flags & ASYNC_CHECK_CD) && (dstatus & SER_DCD)) {
+ if (tty_port_check_carrier(port) && (dstatus & SER_DCD)) {
#if (defined(SERIAL_DEBUG_OPEN) || defined(SERIAL_DEBUG_INTR))
printk("ttyS%d CD now %s...", info->line,
(!(status & SER_DCD)) ? "on" : "off");
@@ -525,7 +525,7 @@
local_irq_save(flags);
- if (port->flags & ASYNC_INITIALIZED) {
+ if (tty_port_initialized(port)) {
free_page(page);
goto errout;
}
@@ -586,7 +586,7 @@
*/
change_speed(tty, info, NULL);
- port->flags |= ASYNC_INITIALIZED;
+ tty_port_set_initialized(port, 1);
local_irq_restore(flags);
return 0;
@@ -604,7 +604,7 @@
unsigned long flags;
struct serial_state *state;
- if (!(info->tport.flags & ASYNC_INITIALIZED))
+ if (!tty_port_initialized(&info->tport))
return;
state = info;
@@ -645,7 +645,7 @@
set_bit(TTY_IO_ERROR, &tty->flags);
- info->tport.flags &= ~ASYNC_INITIALIZED;
+ tty_port_set_initialized(&info->tport, 0);
local_irq_restore(flags);
}
@@ -727,17 +727,12 @@
info->IER &= ~UART_IER_MSI;
if (port->flags & ASYNC_HARDPPS_CD)
info->IER |= UART_IER_MSI;
- if (cflag & CRTSCTS) {
- port->flags |= ASYNC_CTS_FLOW;
+ tty_port_set_cts_flow(port, cflag & CRTSCTS);
+ if (cflag & CRTSCTS)
info->IER |= UART_IER_MSI;
- } else
- port->flags &= ~ASYNC_CTS_FLOW;
- if (cflag & CLOCAL)
- port->flags &= ~ASYNC_CHECK_CD;
- else {
- port->flags |= ASYNC_CHECK_CD;
+ tty_port_set_check_carrier(port, ~cflag & CLOCAL);
+ if (~cflag & CLOCAL)
info->IER |= UART_IER_MSI;
- }
/* TBD:
* Does clearing IER_MSI imply that we should disable the VBL interrupt ?
*/
@@ -1089,7 +1084,7 @@
port->low_latency = (port->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
check_and_exit:
- if (port->flags & ASYNC_INITIALIZED) {
+ if (tty_port_initialized(port)) {
if (change_spd) {
if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI)
tty->alt_speed = 57600;
@@ -1143,7 +1138,7 @@
if (serial_paranoia_check(info, tty->name, "rs_ioctl"))
return -ENODEV;
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
control = info->MCR;
@@ -1165,7 +1160,7 @@
if (serial_paranoia_check(info, tty->name, "rs_ioctl"))
return -ENODEV;
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
local_irq_save(flags);
@@ -1250,7 +1245,7 @@
if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
(cmd != TIOCSERCONFIG) && (cmd != TIOCSERGSTRUCT) &&
(cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) {
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
}
@@ -1342,7 +1337,7 @@
/* Handle transition away from B0 status */
if (!(old_termios->c_cflag & CBAUD) && (cflag & CBAUD)) {
info->MCR |= SER_DTR;
- if (!C_CRTSCTS(tty) || !test_bit(TTY_THROTTLED, &tty->flags))
+ if (!C_CRTSCTS(tty) || !tty_throttled(tty))
info->MCR |= SER_RTS;
local_irq_save(flags);
rtsdtr_ctrl(info->MCR);
@@ -1395,7 +1390,7 @@
* line status register.
*/
state->read_status_mask &= ~UART_LSR_DR;
- if (port->flags & ASYNC_INITIALIZED) {
+ if (tty_port_initialized(port)) {
/* disable receive interrupts */
custom.intena = IF_RBF;
mb();
@@ -1495,7 +1490,7 @@
rs_flush_buffer(tty);
shutdown(tty, info);
info->tport.count = 0;
- info->tport.flags &= ~ASYNC_NORMAL_ACTIVE;
+ tty_port_set_active(&info->tport, 0);
info->tport.tty = NULL;
wake_up_interruptible(&info->tport.open_wait);
}
@@ -1543,7 +1538,7 @@
local_irq_save(flags);
status = ciab.pra;
- control = (state->tport.flags & ASYNC_INITIALIZED) ? state->MCR : status;
+ control = tty_port_initialized(&state->tport) ? state->MCR : status;
local_irq_restore(flags);
stat_buf[0] = 0;
diff --git a/drivers/tty/cyclades.c b/drivers/tty/cyclades.c
index d67e542..3840d6b 100644
--- a/drivers/tty/cyclades.c
+++ b/drivers/tty/cyclades.c
@@ -714,7 +714,7 @@
wake_up_interruptible(&info->port.delta_msr_wait);
}
- if ((mdm_change & CyDCD) && (info->port.flags & ASYNC_CHECK_CD)) {
+ if ((mdm_change & CyDCD) && tty_port_check_carrier(&info->port)) {
if (mdm_status & CyDCD)
wake_up_interruptible(&info->port.open_wait);
else
@@ -1119,7 +1119,7 @@
case C_CM_MDCD:
info->icount.dcd++;
delta_count++;
- if (info->port.flags & ASYNC_CHECK_CD) {
+ if (tty_port_check_carrier(&info->port)) {
u32 dcd = fw_ver > 241 ? param :
readl(&info->u.cyz.ch_ctrl->rs_status);
if (dcd & C_RS_DCD)
@@ -1279,7 +1279,7 @@
spin_lock_irqsave(&card->card_lock, flags);
- if (info->port.flags & ASYNC_INITIALIZED)
+ if (tty_port_initialized(&info->port))
goto errout;
if (!info->type) {
@@ -1364,7 +1364,7 @@
/* enable send, recv, modem !!! */
}
- info->port.flags |= ASYNC_INITIALIZED;
+ tty_port_set_initialized(&info->port, 1);
clear_bit(TTY_IO_ERROR, &tty->flags);
info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
@@ -1424,7 +1424,7 @@
struct cyclades_card *card;
unsigned long flags;
- if (!(info->port.flags & ASYNC_INITIALIZED))
+ if (!tty_port_initialized(&info->port))
return;
card = info->card;
@@ -1448,7 +1448,7 @@
some later date (after testing)!!! */
set_bit(TTY_IO_ERROR, &tty->flags);
- info->port.flags &= ~ASYNC_INITIALIZED;
+ tty_port_set_initialized(&info->port, 0);
spin_unlock_irqrestore(&card->card_lock, flags);
} else {
#ifdef CY_DEBUG_OPEN
@@ -1473,7 +1473,7 @@
tty_port_lower_dtr_rts(&info->port);
set_bit(TTY_IO_ERROR, &tty->flags);
- info->port.flags &= ~ASYNC_INITIALIZED;
+ tty_port_set_initialized(&info->port, 0);
spin_unlock_irqrestore(&card->card_lock, flags);
}
@@ -1711,7 +1711,7 @@
/* Stop accepting input */
cyy_writeb(info, CyCAR, channel & 0x03);
cyy_writeb(info, CySRER, cyy_readb(info, CySRER) & ~CyRxData);
- if (info->port.flags & ASYNC_INITIALIZED) {
+ if (tty_port_initialized(&info->port)) {
/* Waiting for on-board buffers to be empty before
closing the port */
spin_unlock_irqrestore(&card->card_lock, flags);
@@ -2083,17 +2083,12 @@
info->cor1 |= CyPARITY_NONE;
/* CTS flow control flag */
- if (cflag & CRTSCTS) {
- info->port.flags |= ASYNC_CTS_FLOW;
+ tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
+ if (cflag & CRTSCTS)
info->cor2 |= CyCtsAE;
- } else {
- info->port.flags &= ~ASYNC_CTS_FLOW;
- info->cor2 &= ~CyCtsAE;
- }
- if (cflag & CLOCAL)
- info->port.flags &= ~ASYNC_CHECK_CD;
else
- info->port.flags |= ASYNC_CHECK_CD;
+ info->cor2 &= ~CyCtsAE;
+ tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
/***********************************************
The hardware option, CyRtsAO, presents RTS when
@@ -2234,7 +2229,7 @@
}
/* As the HW flow control is done in firmware, the driver
doesn't need to care about it */
- info->port.flags &= ~ASYNC_CTS_FLOW;
+ tty_port_set_cts_flow(&info->port, 0);
/* XON/XOFF/XANY flow control flags */
sw_flow = 0;
@@ -2252,10 +2247,7 @@
}
/* CD sensitivity */
- if (cflag & CLOCAL)
- info->port.flags &= ~ASYNC_CHECK_CD;
- else
- info->port.flags |= ASYNC_CHECK_CD;
+ tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
if (baud == 0) { /* baud rate is zero, turn off line */
cy_writel(&ch_ctrl->rs_control,
@@ -2342,7 +2334,7 @@
info->port.closing_wait = new_serial.closing_wait * HZ / 100;
check_and_exit:
- if (info->port.flags & ASYNC_INITIALIZED) {
+ if (tty_port_initialized(&info->port)) {
cy_set_line_char(info, tty);
ret = 0;
} else {
diff --git a/drivers/tty/hvc/hvc_console.c b/drivers/tty/hvc/hvc_console.c
index e46d628..ce86487 100644
--- a/drivers/tty/hvc/hvc_console.c
+++ b/drivers/tty/hvc/hvc_console.c
@@ -632,7 +632,7 @@
goto bail;
/* Now check if we can get data (are we throttled ?) */
- if (test_bit(TTY_THROTTLED, &tty->flags))
+ if (tty_throttled(tty))
goto throttled;
/* If we aren't notifier driven and aren't throttled, we always
@@ -814,7 +814,7 @@
n = hp->ops->get_chars(hp->vtermno, &ch, 1);
- if (n == 0)
+ if (n <= 0)
return NO_POLL_CHAR;
return ch;
diff --git a/drivers/tty/hvc/hvcs.c b/drivers/tty/hvc/hvcs.c
index 5997b17..3c4d7c2b 100644
--- a/drivers/tty/hvc/hvcs.c
+++ b/drivers/tty/hvc/hvcs.c
@@ -600,7 +600,7 @@
hvcs_try_write(hvcsd);
- if (!tty || test_bit(TTY_THROTTLED, &tty->flags)) {
+ if (!tty || tty_throttled(tty)) {
hvcsd->todo_mask &= ~(HVCS_READ_MASK);
goto bail;
} else if (!(hvcsd->todo_mask & (HVCS_READ_MASK)))
diff --git a/drivers/tty/hvc/hvsi.c b/drivers/tty/hvc/hvsi.c
index a75146f..96ce6bd 100644
--- a/drivers/tty/hvc/hvsi.c
+++ b/drivers/tty/hvc/hvsi.c
@@ -509,7 +509,7 @@
}
spin_lock_irqsave(&hp->lock, flags);
- if (tty && hp->n_throttle && !test_bit(TTY_THROTTLED, &tty->flags)) {
+ if (tty && hp->n_throttle && !tty_throttled(tty)) {
/* we weren't hung up and we weren't throttled, so we can
* deliver the rest now */
hvsi_send_overflow(hp);
diff --git a/drivers/tty/ipwireless/hardware.c b/drivers/tty/ipwireless/hardware.c
index ad7031a..df0204b 100644
--- a/drivers/tty/ipwireless/hardware.c
+++ b/drivers/tty/ipwireless/hardware.c
@@ -1572,6 +1572,11 @@
sizeof(struct ipw_setup_reboot_msg_ack),
ADDR_SETUP_PROT, TL_PROTOCOLID_SETUP,
TL_SETUP_SIGNO_REBOOT_MSG_ACK);
+ if (!packet) {
+ pr_err(IPWIRELESS_PCCARD_NAME
+ ": Not enough memory to send reboot packet");
+ break;
+ }
packet->header.length =
sizeof(struct TlSetupRebootMsgAck);
send_packet(hw, PRIO_SETUP, &packet->header);
diff --git a/drivers/tty/isicom.c b/drivers/tty/isicom.c
index 8bf6763..b70187b 100644
--- a/drivers/tty/isicom.c
+++ b/drivers/tty/isicom.c
@@ -438,8 +438,8 @@
for (; count > 0; count--, port++) {
/* port not active or tx disabled to force flow control */
- if (!(port->port.flags & ASYNC_INITIALIZED) ||
- !(port->status & ISI_TXOK))
+ if (!tty_port_initialized(&port->port) ||
+ !(port->status & ISI_TXOK))
continue;
txcount = min_t(short, TX_SIZE, port->xmit_cnt);
@@ -553,7 +553,7 @@
return IRQ_HANDLED;
}
port = card->ports + channel;
- if (!(port->port.flags & ASYNC_INITIALIZED)) {
+ if (!tty_port_initialized(&port->port)) {
outw(0x0000, base+0x04); /* enable interrupts */
spin_unlock(&card->card_lock);
return IRQ_HANDLED;
@@ -577,7 +577,7 @@
header = inw(base);
switch (header & 0xff) {
case 0: /* Change in EIA signals */
- if (port->port.flags & ASYNC_CHECK_CD) {
+ if (tty_port_check_carrier(&port->port)) {
if (port->status & ISI_DCD) {
if (!(header & ISI_DCD)) {
/* Carrier has been lost */
@@ -758,18 +758,13 @@
outw(channel_setup, base);
InterruptTheCard(base);
}
- if (C_CLOCAL(tty))
- port->port.flags &= ~ASYNC_CHECK_CD;
- else
- port->port.flags |= ASYNC_CHECK_CD;
+ tty_port_set_check_carrier(&port->port, !C_CLOCAL(tty));
/* flow control settings ...*/
flow_ctrl = 0;
- port->port.flags &= ~ASYNC_CTS_FLOW;
- if (C_CRTSCTS(tty)) {
- port->port.flags |= ASYNC_CTS_FLOW;
+ tty_port_set_cts_flow(&port->port, C_CRTSCTS(tty));
+ if (C_CRTSCTS(tty))
flow_ctrl |= ISICOM_CTSRTS;
- }
if (I_IXON(tty))
flow_ctrl |= ISICOM_RESPOND_XONXOFF;
if (I_IXOFF(tty))
diff --git a/drivers/tty/moxa.c b/drivers/tty/moxa.c
index 92982d7..60d37b2 100644
--- a/drivers/tty/moxa.c
+++ b/drivers/tty/moxa.c
@@ -912,7 +912,7 @@
/* pci hot-un-plug support */
for (a = 0; a < brd->numPorts; a++)
- if (brd->ports[a].port.flags & ASYNC_INITIALIZED)
+ if (tty_port_initialized(&brd->ports[a].port))
tty_port_tty_hangup(&brd->ports[a].port, false);
for (a = 0; a < MAX_PORTS_PER_BOARD; a++)
@@ -921,7 +921,7 @@
while (1) {
opened = 0;
for (a = 0; a < brd->numPorts; a++)
- if (brd->ports[a].port.flags & ASYNC_INITIALIZED)
+ if (tty_port_initialized(&brd->ports[a].port))
opened++;
mutex_unlock(&moxa_openlock);
if (!opened)
@@ -1192,13 +1192,13 @@
tty->driver_data = ch;
tty_port_tty_set(&ch->port, tty);
mutex_lock(&ch->port.mutex);
- if (!(ch->port.flags & ASYNC_INITIALIZED)) {
+ if (!tty_port_initialized(&ch->port)) {
ch->statusflags = 0;
moxa_set_tty_param(tty, &tty->termios);
MoxaPortLineCtrl(ch, 1, 1);
MoxaPortEnable(ch);
MoxaSetFifo(ch, ch->type == PORT_16550A);
- ch->port.flags |= ASYNC_INITIALIZED;
+ tty_port_set_initialized(&ch->port, 1);
}
mutex_unlock(&ch->port.mutex);
mutex_unlock(&moxa_openlock);
@@ -1379,7 +1379,7 @@
{
struct tty_struct *tty = tty_port_tty_get(&p->port);
void __iomem *ofsAddr;
- unsigned int inited = p->port.flags & ASYNC_INITIALIZED;
+ unsigned int inited = tty_port_initialized(&p->port);
u16 intr;
if (tty) {
@@ -1394,7 +1394,7 @@
tty_wakeup(tty);
}
- if (inited && !test_bit(TTY_THROTTLED, &tty->flags) &&
+ if (inited && !tty_throttled(tty) &&
MoxaPortRxQueue(p) > 0) { /* RX */
MoxaPortReadData(p);
tty_schedule_flip(&p->port);
diff --git a/drivers/tty/mxser.c b/drivers/tty/mxser.c
index 2f12bb9..98d2bd1 100644
--- a/drivers/tty/mxser.c
+++ b/drivers/tty/mxser.c
@@ -711,8 +711,8 @@
/* CTS flow control flag and modem status interrupts */
info->IER &= ~UART_IER_MSI;
info->MCR &= ~UART_MCR_AFE;
+ tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
if (cflag & CRTSCTS) {
- info->port.flags |= ASYNC_CTS_FLOW;
info->IER |= UART_IER_MSI;
if ((info->type == PORT_16550A) || (info->board->chip_flag)) {
info->MCR |= UART_MCR_AFE;
@@ -744,16 +744,11 @@
}
}
}
- } else {
- info->port.flags &= ~ASYNC_CTS_FLOW;
}
outb(info->MCR, info->ioaddr + UART_MCR);
- if (cflag & CLOCAL) {
- info->port.flags &= ~ASYNC_CHECK_CD;
- } else {
- info->port.flags |= ASYNC_CHECK_CD;
+ tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
+ if (~cflag & CLOCAL)
info->IER |= UART_IER_MSI;
- }
outb(info->IER, info->ioaddr + UART_IER);
/*
@@ -826,7 +821,7 @@
port->mon_data.modem_status = status;
wake_up_interruptible(&port->port.delta_msr_wait);
- if ((port->port.flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) {
+ if (tty_port_check_carrier(&port->port) && (status & UART_MSR_DDCD)) {
if (status & UART_MSR_DCD)
wake_up_interruptible(&port->port.open_wait);
}
@@ -1086,12 +1081,10 @@
mutex_lock(&port->mutex);
mxser_close_port(port);
mxser_flush_buffer(tty);
- if (test_bit(ASYNCB_INITIALIZED, &port->flags)) {
- if (C_HUPCL(tty))
- tty_port_lower_dtr_rts(port);
- }
+ if (tty_port_initialized(port) && C_HUPCL(tty))
+ tty_port_lower_dtr_rts(port);
mxser_shutdown_port(port);
- clear_bit(ASYNCB_INITIALIZED, &port->flags);
+ tty_port_set_initialized(port, 0);
mutex_unlock(&port->mutex);
info->closing = 0;
/* Right now the tty_port set is done outside of the close_end helper
@@ -1287,7 +1280,7 @@
process_txrx_fifo(info);
- if (test_bit(ASYNCB_INITIALIZED, &port->flags)) {
+ if (tty_port_initialized(port)) {
if (flags != (port->flags & ASYNC_SPD_MASK)) {
spin_lock_irqsave(&info->slock, sl_flags);
mxser_change_speed(tty, NULL);
@@ -1296,7 +1289,7 @@
} else {
retval = mxser_activate(port, tty);
if (retval == 0)
- set_bit(ASYNCB_INITIALIZED, &port->flags);
+ tty_port_set_initialized(port, 1);
}
return retval;
}
@@ -1334,7 +1327,7 @@
if (tty->index == MXSER_PORTS)
return -ENOIOCTLCMD;
- if (test_bit(TTY_IO_ERROR, &tty->flags))
+ if (tty_io_error(tty))
return -EIO;
control = info->MCR;
@@ -1361,7 +1354,7 @@
if (tty->index == MXSER_PORTS)
return -ENOIOCTLCMD;
- if (test_bit(TTY_IO_ERROR, &tty->flags))
+ if (tty_io_error(tty))
return -EIO;
spin_lock_irqsave(&info->slock, flags);
@@ -1715,8 +1708,7 @@
return 0;
}
- if (cmd != TIOCGSERIAL && cmd != TIOCMIWAIT &&
- test_bit(TTY_IO_ERROR, &tty->flags))
+ if (cmd != TIOCGSERIAL && cmd != TIOCMIWAIT && tty_io_error(tty))
return -EIO;
switch (cmd) {
@@ -2257,7 +2249,7 @@
iir &= MOXA_MUST_IIR_MASK;
tty = tty_port_tty_get(&port->port);
if (!tty || port->closing ||
- !(port->port.flags & ASYNC_INITIALIZED)) {
+ !tty_port_initialized(&port->port)) {
status = inb(port->ioaddr + UART_LSR);
outb(0x27, port->ioaddr + UART_FCR);
inb(port->ioaddr + UART_MSR);
@@ -2400,7 +2392,6 @@
if (brd->chip_flag != MOXA_OTHER_UART)
mxser_enable_must_enchance_mode(info->ioaddr);
- info->port.flags = ASYNC_SHARE_IRQ;
info->type = brd->uart_type;
process_txrx_fifo(info);
diff --git a/drivers/tty/n_gsm.c b/drivers/tty/n_gsm.c
index 0c27a00..54cab59 100644
--- a/drivers/tty/n_gsm.c
+++ b/drivers/tty/n_gsm.c
@@ -2045,7 +2045,9 @@
}
}
spin_unlock(&gsm_mux_lock);
- WARN_ON(i == MAX_MUX);
+ /* open failed before registering => nothing to do */
+ if (i == MAX_MUX)
+ return;
/* In theory disconnecting DLCI 0 is sufficient but for some
modems this is apparently not the case. */
@@ -2947,7 +2949,7 @@
dlci->modem_rx = 0;
/* We could in theory open and close before we wait - eg if we get
a DM straight back. This is ok as that will have caused a hangup */
- set_bit(ASYNCB_INITIALIZED, &port->flags);
+ tty_port_set_initialized(port, 1);
/* Start sending off SABM messages */
gsm_dlci_begin_open(dlci);
/* And wait for virtual carrier */
@@ -2970,10 +2972,8 @@
if (tty_port_close_start(&dlci->port, tty, filp) == 0)
return;
gsm_dlci_begin_close(dlci);
- if (test_bit(ASYNCB_INITIALIZED, &dlci->port.flags)) {
- if (C_HUPCL(tty))
- tty_port_lower_dtr_rts(&dlci->port);
- }
+ if (tty_port_initialized(&dlci->port) && C_HUPCL(tty))
+ tty_port_lower_dtr_rts(&dlci->port);
tty_port_close_end(&dlci->port, tty);
tty_port_tty_set(&dlci->port, NULL);
return;
diff --git a/drivers/tty/n_hdlc.c b/drivers/tty/n_hdlc.c
index bcaba17..a7fa016 100644
--- a/drivers/tty/n_hdlc.c
+++ b/drivers/tty/n_hdlc.c
@@ -599,7 +599,7 @@
add_wait_queue(&tty->read_wait, &wait);
for (;;) {
- if (test_bit(TTY_OTHER_DONE, &tty->flags)) {
+ if (test_bit(TTY_OTHER_CLOSED, &tty->flags)) {
ret = -EIO;
break;
}
@@ -827,7 +827,7 @@
/* set bits for operations that won't block */
if (n_hdlc->rx_buf_list.head)
mask |= POLLIN | POLLRDNORM; /* readable */
- if (test_bit(TTY_OTHER_DONE, &tty->flags))
+ if (test_bit(TTY_OTHER_CLOSED, &tty->flags))
mask |= POLLHUP;
if (tty_hung_up_p(filp))
mask |= POLLHUP;
diff --git a/drivers/tty/n_tty.c b/drivers/tty/n_tty.c
index fb76a7d..bdf0e6e 100644
--- a/drivers/tty/n_tty.c
+++ b/drivers/tty/n_tty.c
@@ -1917,18 +1917,6 @@
return ldata->commit_head - ldata->read_tail >= amt;
}
-static inline int check_other_done(struct tty_struct *tty)
-{
- int done = test_bit(TTY_OTHER_DONE, &tty->flags);
- if (done) {
- /* paired with cmpxchg() in check_other_closed(); ensures
- * read buffer head index is not stale
- */
- smp_mb__after_atomic();
- }
- return done;
-}
-
/**
* copy_from_read_buf - copy read data directly
* @tty: terminal device
@@ -2124,7 +2112,7 @@
struct n_tty_data *ldata = tty->disc_data;
unsigned char __user *b = buf;
DEFINE_WAIT_FUNC(wait, woken_wake_function);
- int c, done;
+ int c;
int minimum, time;
ssize_t retval = 0;
long timeout;
@@ -2183,32 +2171,35 @@
break;
}
- done = check_other_done(tty);
-
if (!input_available_p(tty, 0)) {
- if (done) {
- retval = -EIO;
- break;
- }
- if (tty_hung_up_p(file))
- break;
- if (!timeout)
- break;
- if (file->f_flags & O_NONBLOCK) {
- retval = -EAGAIN;
- break;
- }
- if (signal_pending(current)) {
- retval = -ERESTARTSYS;
- break;
- }
up_read(&tty->termios_rwsem);
-
- timeout = wait_woken(&wait, TASK_INTERRUPTIBLE,
- timeout);
-
+ tty_buffer_flush_work(tty->port);
down_read(&tty->termios_rwsem);
- continue;
+ if (!input_available_p(tty, 0)) {
+ if (test_bit(TTY_OTHER_CLOSED, &tty->flags)) {
+ retval = -EIO;
+ break;
+ }
+ if (tty_hung_up_p(file))
+ break;
+ if (!timeout)
+ break;
+ if (file->f_flags & O_NONBLOCK) {
+ retval = -EAGAIN;
+ break;
+ }
+ if (signal_pending(current)) {
+ retval = -ERESTARTSYS;
+ break;
+ }
+ up_read(&tty->termios_rwsem);
+
+ timeout = wait_woken(&wait, TASK_INTERRUPTIBLE,
+ timeout);
+
+ down_read(&tty->termios_rwsem);
+ continue;
+ }
}
if (ldata->icanon && !L_EXTPROC(tty)) {
@@ -2386,12 +2377,17 @@
poll_wait(file, &tty->read_wait, wait);
poll_wait(file, &tty->write_wait, wait);
- if (check_other_done(tty))
- mask |= POLLHUP;
if (input_available_p(tty, 1))
mask |= POLLIN | POLLRDNORM;
+ else {
+ tty_buffer_flush_work(tty->port);
+ if (input_available_p(tty, 1))
+ mask |= POLLIN | POLLRDNORM;
+ }
if (tty->packet && tty->link->ctrl_status)
mask |= POLLPRI | POLLIN | POLLRDNORM;
+ if (test_bit(TTY_OTHER_CLOSED, &tty->flags))
+ mask |= POLLHUP;
if (tty_hung_up_p(file))
mask |= POLLHUP;
if (tty->ops->write && !tty_is_writelocked(tty) &&
diff --git a/drivers/tty/nozomi.c b/drivers/tty/nozomi.c
index 5cc80b8..d6fd0e8 100644
--- a/drivers/tty/nozomi.c
+++ b/drivers/tty/nozomi.c
@@ -826,7 +826,7 @@
size = __le32_to_cpu(readl(addr));
/* DBG1( "%d bytes port: %d", size, index); */
- if (tty && test_bit(TTY_THROTTLED, &tty->flags)) {
+ if (tty && tty_throttled(tty)) {
DBG1("No room in tty, don't read data, don't ack interrupt, "
"disable interrupt");
diff --git a/drivers/tty/pty.c b/drivers/tty/pty.c
index cf0dc51..dd4b841 100644
--- a/drivers/tty/pty.c
+++ b/drivers/tty/pty.c
@@ -44,7 +44,7 @@
if (tty->driver->subtype == PTY_TYPE_MASTER)
WARN_ON(tty->count > 1);
else {
- if (test_bit(TTY_IO_ERROR, &tty->flags))
+ if (tty_io_error(tty))
return;
if (tty->count > 2)
return;
@@ -59,7 +59,7 @@
if (!tty->link)
return;
set_bit(TTY_OTHER_CLOSED, &tty->link->flags);
- tty_flip_buffer_push(tty->link->port);
+ wake_up_interruptible(&tty->link->read_wait);
wake_up_interruptible(&tty->link->write_wait);
if (tty->driver->subtype == PTY_TYPE_MASTER) {
set_bit(TTY_OTHER_CLOSED, &tty->flags);
@@ -247,9 +247,7 @@
goto out;
clear_bit(TTY_IO_ERROR, &tty->flags);
- /* TTY_OTHER_CLOSED must be cleared before TTY_OTHER_DONE */
clear_bit(TTY_OTHER_CLOSED, &tty->link->flags);
- clear_bit(TTY_OTHER_DONE, &tty->link->flags);
set_bit(TTY_THROTTLED, &tty->flags);
return 0;
diff --git a/drivers/tty/rocket.c b/drivers/tty/rocket.c
index 0b802cd..b0cc47c 100644
--- a/drivers/tty/rocket.c
+++ b/drivers/tty/rocket.c
@@ -495,7 +495,7 @@
if (!info)
return;
- if ((info->port.flags & ASYNC_INITIALIZED) == 0) {
+ if (!tty_port_initialized(&info->port)) {
printk(KERN_WARNING "rp: WARNING: rp_handle_port called with "
"info->flags & NOT_INIT\n");
return;
@@ -615,7 +615,8 @@
* the board.
* Inputs: board, aiop, chan numbers
*/
-static void init_r_port(int board, int aiop, int chan, struct pci_dev *pci_dev)
+static void __init
+init_r_port(int board, int aiop, int chan, struct pci_dev *pci_dev)
{
unsigned rocketMode;
struct r_port *info;
@@ -920,7 +921,7 @@
/*
* Info->count is now 1; so it's safe to sleep now.
*/
- if (!test_bit(ASYNCB_INITIALIZED, &port->flags)) {
+ if (!tty_port_initialized(port)) {
cp = &info->channel;
sSetRxTrigger(cp, TRIG_1);
if (sGetChanStatus(cp) & CD_ACT)
@@ -944,7 +945,7 @@
sEnRxFIFO(cp);
sEnTransmit(cp);
- set_bit(ASYNCB_INITIALIZED, &info->port.flags);
+ tty_port_set_initialized(&info->port, 1);
/*
* Set up the tty->alt_speed kludge
@@ -1042,9 +1043,10 @@
}
}
spin_lock_irq(&port->lock);
- info->port.flags &= ~(ASYNC_INITIALIZED | ASYNC_NORMAL_ACTIVE);
tty->closing = 0;
spin_unlock_irq(&port->lock);
+ tty_port_set_initialized(port, 0);
+ tty_port_set_active(port, 0);
mutex_unlock(&port->mutex);
tty_port_tty_set(port, NULL);
@@ -1512,7 +1514,7 @@
sDisCTSFlowCtl(cp);
sDisTxSoftFlowCtl(cp);
sClrTxXOFF(cp);
- clear_bit(ASYNCB_INITIALIZED, &info->port.flags);
+ tty_port_set_initialized(&info->port, 0);
wake_up_interruptible(&info->port.open_wait);
}
@@ -1624,7 +1626,7 @@
/* Write remaining data into the port's xmit_buf */
while (1) {
/* Hung up ? */
- if (!test_bit(ASYNCB_NORMAL_ACTIVE, &info->port.flags))
+ if (!tty_port_active(&info->port))
goto end;
c = min(count, XMIT_BUF_SIZE - info->xmit_cnt - 1);
c = min(c, XMIT_BUF_SIZE - info->xmit_head);
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index 047a7ba..215a992 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -17,7 +17,7 @@
struct uart_8250_dma {
int (*tx_dma)(struct uart_8250_port *p);
- int (*rx_dma)(struct uart_8250_port *p, unsigned int iir);
+ int (*rx_dma)(struct uart_8250_port *p);
/* Filter function */
dma_filter_fn fn;
@@ -84,7 +84,6 @@
#define UART_BUG_THRE (1 << 3) /* UART has buggy THRE reassertion */
#define UART_BUG_PARITY (1 << 4) /* UART mishandles parity if FIFO enabled */
-#define HIGH_BITS_OFFSET ((sizeof(long)-sizeof(int))*8)
#ifdef CONFIG_SERIAL_8250_SHARE_IRQ
#define SERIAL8250_SHARE_IRQS 1
@@ -151,6 +150,12 @@
static inline void serial8250_pnp_exit(void) { }
#endif
+#ifdef CONFIG_SERIAL_8250_FINTEK
+int fintek_8250_probe(struct uart_8250_port *uart);
+#else
+static inline int fintek_8250_probe(struct uart_8250_port *uart) { return 0; }
+#endif
+
#ifdef CONFIG_ARCH_OMAP1
static inline int is_omap1_8250(struct uart_8250_port *pt)
{
@@ -190,7 +195,8 @@
#ifdef CONFIG_SERIAL_8250_DMA
extern int serial8250_tx_dma(struct uart_8250_port *);
-extern int serial8250_rx_dma(struct uart_8250_port *, unsigned int iir);
+extern int serial8250_rx_dma(struct uart_8250_port *);
+extern void serial8250_rx_dma_flush(struct uart_8250_port *);
extern int serial8250_request_dma(struct uart_8250_port *);
extern void serial8250_release_dma(struct uart_8250_port *);
#else
@@ -198,10 +204,11 @@
{
return -1;
}
-static inline int serial8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
+static inline int serial8250_rx_dma(struct uart_8250_port *p)
{
return -1;
}
+static inline void serial8250_rx_dma_flush(struct uart_8250_port *p) { }
static inline int serial8250_request_dma(struct uart_8250_port *p)
{
return -1;
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index 2f4f5ee..0fbd7c0 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -830,6 +830,7 @@
uart.port.handle_irq = p->handle_irq;
uart.port.handle_break = p->handle_break;
uart.port.set_termios = p->set_termios;
+ uart.port.get_mctrl = p->get_mctrl;
uart.port.pm = p->pm;
uart.port.dev = &dev->dev;
uart.port.irqflags |= irqflag;
@@ -1022,6 +1023,8 @@
/* Possibly override set_termios call */
if (up->port.set_termios)
uart->port.set_termios = up->port.set_termios;
+ if (up->port.get_mctrl)
+ uart->port.get_mctrl = up->port.get_mctrl;
if (up->port.set_mctrl)
uart->port.set_mctrl = up->port.set_mctrl;
if (up->port.startup)
diff --git a/drivers/tty/serial/8250/8250_dma.c b/drivers/tty/serial/8250/8250_dma.c
index 78259d3..7f33d1c 100644
--- a/drivers/tty/serial/8250/8250_dma.c
+++ b/drivers/tty/serial/8250/8250_dma.c
@@ -110,30 +110,11 @@
return ret;
}
-int serial8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
+int serial8250_rx_dma(struct uart_8250_port *p)
{
struct uart_8250_dma *dma = p->dma;
struct dma_async_tx_descriptor *desc;
- switch (iir & 0x3f) {
- case UART_IIR_RLSI:
- /* 8250_core handles errors and break interrupts */
- return -EIO;
- case UART_IIR_RX_TIMEOUT:
- /*
- * If RCVR FIFO trigger level was not reached, complete the
- * transfer and let 8250_core copy the remaining data.
- */
- if (dma->rx_running) {
- dmaengine_pause(dma->rxchan);
- __dma_rx_complete(p);
- dmaengine_terminate_all(dma->rxchan);
- }
- return -ETIMEDOUT;
- default:
- break;
- }
-
if (dma->rx_running)
return 0;
@@ -154,10 +135,23 @@
return 0;
}
+void serial8250_rx_dma_flush(struct uart_8250_port *p)
+{
+ struct uart_8250_dma *dma = p->dma;
+
+ if (dma->rx_running) {
+ dmaengine_pause(dma->rxchan);
+ __dma_rx_complete(p);
+ dmaengine_terminate_all(dma->rxchan);
+ }
+}
+
int serial8250_request_dma(struct uart_8250_port *p)
{
struct uart_8250_dma *dma = p->dma;
dma_cap_mask_t mask;
+ struct dma_slave_caps caps;
+ int ret;
/* Default slave configuration parameters */
dma->rxconf.direction = DMA_DEV_TO_MEM;
@@ -178,6 +172,16 @@
if (!dma->rxchan)
return -ENODEV;
+ /* 8250 rx dma requires dmaengine driver to support pause/terminate */
+ ret = dma_get_slave_caps(dma->rxchan, &caps);
+ if (ret)
+ goto release_rx;
+ if (!caps.cmd_pause || !caps.cmd_terminate ||
+ caps.residue_granularity == DMA_RESIDUE_GRANULARITY_DESCRIPTOR) {
+ ret = -EINVAL;
+ goto release_rx;
+ }
+
dmaengine_slave_config(dma->rxchan, &dma->rxconf);
/* Get a channel for TX */
@@ -185,8 +189,17 @@
dma->fn, dma->tx_param,
p->port.dev, "tx");
if (!dma->txchan) {
- dma_release_channel(dma->rxchan);
- return -ENODEV;
+ ret = -ENODEV;
+ goto release_rx;
+ }
+
+ /* 8250 tx dma requires dmaengine driver to support terminate */
+ ret = dma_get_slave_caps(dma->txchan, &caps);
+ if (ret)
+ goto err;
+ if (!caps.cmd_terminate) {
+ ret = -EINVAL;
+ goto err;
}
dmaengine_slave_config(dma->txchan, &dma->txconf);
@@ -197,8 +210,10 @@
dma->rx_buf = dma_alloc_coherent(dma->rxchan->device->dev, dma->rx_size,
&dma->rx_addr, GFP_KERNEL);
- if (!dma->rx_buf)
+ if (!dma->rx_buf) {
+ ret = -ENOMEM;
goto err;
+ }
/* TX buffer */
dma->tx_addr = dma_map_single(dma->txchan->device->dev,
@@ -208,6 +223,7 @@
if (dma_mapping_error(dma->txchan->device->dev, dma->tx_addr)) {
dma_free_coherent(dma->rxchan->device->dev, dma->rx_size,
dma->rx_buf, dma->rx_addr);
+ ret = -ENOMEM;
goto err;
}
@@ -215,10 +231,10 @@
return 0;
err:
- dma_release_channel(dma->rxchan);
dma_release_channel(dma->txchan);
-
- return -ENOMEM;
+release_rx:
+ dma_release_channel(dma->rxchan);
+ return ret;
}
EXPORT_SYMBOL_GPL(serial8250_request_dma);
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index a3fb95d..e199696 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -104,15 +104,16 @@
dw8250_force_idle(p);
#ifdef CONFIG_64BIT
- __raw_writeq(value & 0xff, offset);
-#else
+ if (p->type == PORT_OCTEON)
+ __raw_writeq(value & 0xff, offset);
+ else
+#endif
if (p->iotype == UPIO_MEM32)
writel(value, offset);
else if (p->iotype == UPIO_MEM32BE)
iowrite32be(value, offset);
else
writeb(value, offset);
-#endif
}
/*
* FIXME: this deadlocks if port->lock is already held
@@ -617,6 +618,7 @@
{ "8086228A", 0 },
{ "APMC0D08", 0},
{ "AMD0020", 0 },
+ { "AMDI0020", 0 },
{ },
};
MODULE_DEVICE_TABLE(acpi, dw8250_acpi_match);
diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c
index 8947439..870981d 100644
--- a/drivers/tty/serial/8250/8250_fintek.c
+++ b/drivers/tty/serial/8250/8250_fintek.c
@@ -1,9 +1,7 @@
/*
* Probe for F81216A LPC to 4 UART
*
- * Based on drivers/tty/serial/8250_pnp.c, by Russell King, et al
- *
- * Copyright (C) 2014 Ricardo Ribalda, Qtechnology A/S
+ * Copyright (C) 2014-2016 Ricardo Ribalda, Qtechnology A/S
*
*
* This program is free software; you can redistribute it and/or modify
@@ -38,19 +36,15 @@
#define RXW4C_IRA BIT(3)
#define TXW4C_IRA BIT(2)
-#define DRIVER_NAME "8250_fintek"
-
struct fintek_8250 {
u16 base_port;
u8 index;
u8 key;
- long line;
};
static int fintek_8250_enter_key(u16 base_port, u8 key)
{
-
- if (!request_muxed_region(base_port, 2, DRIVER_NAME))
+ if (!request_muxed_region(base_port, 2, "8250_fintek"))
return -EBUSY;
outb(key, base_port + ADDR_PORT);
@@ -138,7 +132,7 @@
return 0;
}
-static int fintek_8250_base_port(u16 io_address, u8 *key, u8 *index)
+static int find_base_port(struct fintek_8250 *pdata, u16 io_address)
{
static const u16 addr[] = {0x4e, 0x2e};
static const u8 keys[] = {0x77, 0xa0, 0x87, 0x67};
@@ -168,10 +162,13 @@
continue;
fintek_8250_exit_key(addr[i]);
- *key = keys[j];
- *index = k;
- return addr[i];
+ pdata->key = keys[j];
+ pdata->base_port = addr[i];
+ pdata->index = k;
+
+ return 0;
}
+
fintek_8250_exit_key(addr[i]);
}
}
@@ -179,104 +176,21 @@
return -ENODEV;
}
-static int
-fintek_8250_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
+int fintek_8250_probe(struct uart_8250_port *uart)
{
- struct uart_8250_port uart;
struct fintek_8250 *pdata;
- int base_port;
- u8 key;
- u8 index;
+ struct fintek_8250 probe_data;
- if (!pnp_port_valid(dev, 0))
+ if (find_base_port(&probe_data, uart->port.iobase))
return -ENODEV;
- base_port = fintek_8250_base_port(pnp_port_start(dev, 0), &key, &index);
- if (base_port < 0)
- return -ENODEV;
-
- memset(&uart, 0, sizeof(uart));
-
- pdata = devm_kzalloc(&dev->dev, sizeof(*pdata), GFP_KERNEL);
+ pdata = devm_kzalloc(uart->port.dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
return -ENOMEM;
- uart.port.private_data = pdata;
- if (!pnp_irq_valid(dev, 0))
- return -ENODEV;
- uart.port.irq = pnp_irq(dev, 0);
- uart.port.iobase = pnp_port_start(dev, 0);
- uart.port.iotype = UPIO_PORT;
- uart.port.rs485_config = fintek_8250_rs485_config;
+ memcpy(pdata, &probe_data, sizeof(probe_data));
+ uart->port.rs485_config = fintek_8250_rs485_config;
+ uart->port.private_data = pdata;
- uart.port.flags |= UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
- if (pnp_irq_flags(dev, 0) & IORESOURCE_IRQ_SHAREABLE)
- uart.port.flags |= UPF_SHARE_IRQ;
- uart.port.uartclk = 1843200;
- uart.port.dev = &dev->dev;
-
- pdata->key = key;
- pdata->base_port = base_port;
- pdata->index = index;
- pdata->line = serial8250_register_8250_port(&uart);
- if (pdata->line < 0)
- return -ENODEV;
-
- pnp_set_drvdata(dev, pdata);
return 0;
}
-
-static void fintek_8250_remove(struct pnp_dev *dev)
-{
- struct fintek_8250 *pdata = pnp_get_drvdata(dev);
-
- if (pdata)
- serial8250_unregister_port(pdata->line);
-}
-
-#ifdef CONFIG_PM
-static int fintek_8250_suspend(struct pnp_dev *dev, pm_message_t state)
-{
- struct fintek_8250 *pdata = pnp_get_drvdata(dev);
-
- if (!pdata)
- return -ENODEV;
- serial8250_suspend_port(pdata->line);
- return 0;
-}
-
-static int fintek_8250_resume(struct pnp_dev *dev)
-{
- struct fintek_8250 *pdata = pnp_get_drvdata(dev);
-
- if (!pdata)
- return -ENODEV;
- serial8250_resume_port(pdata->line);
- return 0;
-}
-#else
-#define fintek_8250_suspend NULL
-#define fintek_8250_resume NULL
-#endif /* CONFIG_PM */
-
-static const struct pnp_device_id fintek_dev_table[] = {
- /* Qtechnology Panel PC / IO1000 */
- { "PNP0501"},
- {}
-};
-
-MODULE_DEVICE_TABLE(pnp, fintek_dev_table);
-
-static struct pnp_driver fintek_8250_driver = {
- .name = DRIVER_NAME,
- .probe = fintek_8250_probe,
- .remove = fintek_8250_remove,
- .suspend = fintek_8250_suspend,
- .resume = fintek_8250_resume,
- .id_table = fintek_dev_table,
-};
-
-module_pnp_driver(fintek_8250_driver);
-MODULE_DESCRIPTION("Fintek F812164 module");
-MODULE_AUTHOR("Ricardo Ribalda <ricardo.ribalda@gmail.com>");
-MODULE_LICENSE("GPL");
diff --git a/drivers/tty/serial/8250/8250_mid.c b/drivers/tty/serial/8250/8250_mid.c
index 88531a3..86379a7 100644
--- a/drivers/tty/serial/8250/8250_mid.c
+++ b/drivers/tty/serial/8250/8250_mid.c
@@ -9,11 +9,13 @@
* published by the Free Software Foundation.
*/
-#include <linux/rational.h>
+#include <linux/bitops.h>
#include <linux/module.h>
#include <linux/pci.h>
+#include <linux/rational.h>
#include <linux/dma/hsu.h>
+#include <linux/8250_pci.h>
#include "8250.h"
@@ -24,6 +26,7 @@
#define PCI_DEVICE_ID_INTEL_DNV_UART 0x19d8
/* Intel MID Specific registers */
+#define INTEL_MID_UART_DNV_FISR 0x08
#define INTEL_MID_UART_PS 0x30
#define INTEL_MID_UART_MUL 0x34
#define INTEL_MID_UART_DIV 0x38
@@ -31,6 +34,7 @@
struct mid8250;
struct mid8250_board {
+ unsigned int flags;
unsigned long freq;
unsigned int base_baud;
int (*setup)(struct mid8250 *, struct uart_port *p);
@@ -76,7 +80,11 @@
struct pci_dev *pdev = to_pci_dev(p->dev);
int index = PCI_FUNC(pdev->devfn);
- /* Currently no support for HSU port0 */
+ /*
+ * Device 0000:00:04.0 is not a real HSU port. It provides a global
+ * register set for all HSU ports, although it has the same PCI ID.
+ * Skip it here.
+ */
if (index-- == 0)
return -ENODEV;
@@ -88,16 +96,16 @@
static int dnv_handle_irq(struct uart_port *p)
{
struct mid8250 *mid = p->private_data;
- int ret;
+ unsigned int fisr = serial_port_in(p, INTEL_MID_UART_DNV_FISR);
+ int ret = IRQ_NONE;
- ret = hsu_dma_irq(&mid->dma_chip, 0);
- ret |= hsu_dma_irq(&mid->dma_chip, 1);
-
- /* For now, letting the HW generate separate interrupt for the UART */
- if (ret)
- return ret;
-
- return serial8250_handle_irq(p, serial_port_in(p, UART_IIR));
+ if (fisr & BIT(2))
+ ret |= hsu_dma_irq(&mid->dma_chip, 1);
+ if (fisr & BIT(1))
+ ret |= hsu_dma_irq(&mid->dma_chip, 0);
+ if (fisr & BIT(0))
+ ret |= serial8250_handle_irq(p, serial_port_in(p, UART_IIR));
+ return ret;
}
#define DNV_DMA_CHAN_OFFSET 0x80
@@ -106,12 +114,13 @@
{
struct hsu_dma_chip *chip = &mid->dma_chip;
struct pci_dev *pdev = to_pci_dev(p->dev);
+ unsigned int bar = FL_GET_BASE(mid->board->flags);
int ret;
chip->dev = &pdev->dev;
chip->irq = pdev->irq;
chip->regs = p->membase;
- chip->length = pci_resource_len(pdev, 0);
+ chip->length = pci_resource_len(pdev, bar);
chip->offset = DNV_DMA_CHAN_OFFSET;
/* Falling back to PIO mode if DMA probing fails */
@@ -217,6 +226,7 @@
{
struct uart_8250_port uart;
struct mid8250 *mid;
+ unsigned int bar;
int ret;
ret = pcim_enable_device(pdev);
@@ -230,6 +240,7 @@
return -ENOMEM;
mid->board = (struct mid8250_board *)id->driver_data;
+ bar = FL_GET_BASE(mid->board->flags);
memset(&uart, 0, sizeof(struct uart_8250_port));
@@ -242,8 +253,8 @@
uart.port.flags = UPF_SHARE_IRQ | UPF_FIXED_PORT | UPF_FIXED_TYPE;
uart.port.set_termios = mid8250_set_termios;
- uart.port.mapbase = pci_resource_start(pdev, 0);
- uart.port.membase = pcim_iomap(pdev, 0, 0);
+ uart.port.mapbase = pci_resource_start(pdev, bar);
+ uart.port.membase = pcim_iomap(pdev, bar, 0);
if (!uart.port.membase)
return -ENOMEM;
@@ -282,18 +293,21 @@
}
static const struct mid8250_board pnw_board = {
+ .flags = FL_BASE0,
.freq = 50000000,
.base_baud = 115200,
.setup = pnw_setup,
};
static const struct mid8250_board tng_board = {
+ .flags = FL_BASE0,
.freq = 38400000,
.base_baud = 1843200,
.setup = tng_setup,
};
static const struct mid8250_board dnv_board = {
+ .flags = FL_BASE1,
.freq = 133333333,
.base_baud = 115200,
.setup = dnv_setup,
diff --git a/drivers/tty/serial/8250/8250_of.c b/drivers/tty/serial/8250/8250_of.c
index c7ed3d2..38963d7 100644
--- a/drivers/tty/serial/8250/8250_of.c
+++ b/drivers/tty/serial/8250/8250_of.c
@@ -29,7 +29,7 @@
};
#ifdef CONFIG_ARCH_TEGRA
-void tegra_serial_handle_break(struct uart_port *p)
+static void tegra_serial_handle_break(struct uart_port *p)
{
unsigned int status, tmout = 10000;
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
index 6f76051..2c44c79 100644
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -115,6 +115,12 @@
bool rx_dma_broken;
};
+#ifdef CONFIG_SERIAL_8250_DMA
+static void omap_8250_rx_dma_flush(struct uart_8250_port *p);
+#else
+static inline void omap_8250_rx_dma_flush(struct uart_8250_port *p) { }
+#endif
+
static u32 uart_read(struct uart_8250_port *up, u32 reg)
{
return readl(up->port.membase + (reg << up->port.regshift));
@@ -635,7 +641,7 @@
serial_out(up, UART_OMAP_WER, priv->wer);
if (up->dma)
- up->dma->rx_dma(up, 0);
+ up->dma->rx_dma(up);
pm_runtime_mark_last_busy(port->dev);
pm_runtime_put_autosuspend(port->dev);
@@ -654,7 +660,7 @@
flush_work(&priv->qos_work);
if (up->dma)
- up->dma->rx_dma(up, UART_IIR_RX_TIMEOUT);
+ omap_8250_rx_dma_flush(up);
pm_runtime_get_sync(port->dev);
@@ -742,9 +748,9 @@
}
#ifdef CONFIG_SERIAL_8250_DMA
-static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir);
+static int omap_8250_rx_dma(struct uart_8250_port *p);
-static void __dma_rx_do_complete(struct uart_8250_port *p, bool error)
+static void __dma_rx_do_complete(struct uart_8250_port *p)
{
struct omap8250_priv *priv = p->port.private_data;
struct uart_8250_dma *dma = p->dma;
@@ -754,9 +760,6 @@
unsigned long flags;
int ret;
- dma_sync_single_for_cpu(dma->rxchan->device->dev, dma->rx_addr,
- dma->rx_size, DMA_FROM_DEVICE);
-
spin_lock_irqsave(&priv->rx_dma_lock, flags);
if (!dma->rx_running)
@@ -764,7 +767,6 @@
dma->rx_running = 0;
dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
- dmaengine_terminate_all(dma->rxchan);
count = dma->rx_size - state.residue;
@@ -775,15 +777,13 @@
unlock:
spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
- if (!error)
- omap_8250_rx_dma(p, 0);
-
tty_flip_buffer_push(tty_port);
}
static void __dma_rx_complete(void *param)
{
- __dma_rx_do_complete(param, false);
+ __dma_rx_do_complete(param);
+ omap_8250_rx_dma(param);
}
static void omap_8250_rx_dma_flush(struct uart_8250_port *p)
@@ -806,10 +806,11 @@
spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
- __dma_rx_do_complete(p, true);
+ __dma_rx_do_complete(p);
+ dmaengine_terminate_all(dma->rxchan);
}
-static int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
+static int omap_8250_rx_dma(struct uart_8250_port *p)
{
struct omap8250_priv *priv = p->port.private_data;
struct uart_8250_dma *dma = p->dma;
@@ -817,35 +818,6 @@
struct dma_async_tx_descriptor *desc;
unsigned long flags;
- switch (iir & 0x3f) {
- case UART_IIR_RLSI:
- /* 8250_core handles errors and break interrupts */
- omap_8250_rx_dma_flush(p);
- return -EIO;
- case UART_IIR_RX_TIMEOUT:
- /*
- * If RCVR FIFO trigger level was not reached, complete the
- * transfer and let 8250_core copy the remaining data.
- */
- omap_8250_rx_dma_flush(p);
- return -ETIMEDOUT;
- case UART_IIR_RDI:
- /*
- * The OMAP UART is a special BEAST. If we receive RDI we _have_
- * a DMA transfer programmed but it didn't work. One reason is
- * that we were too slow and there were too many bytes in the
- * FIFO, the UART counted wrong and never kicked the DMA engine
- * to do anything. That means once we receive RDI on OMAP then
- * the DMA won't do anything soon so we have to cancel the DMA
- * transfer and purge the FIFO manually.
- */
- omap_8250_rx_dma_flush(p);
- return -ETIMEDOUT;
-
- default:
- break;
- }
-
if (priv->rx_dma_broken)
return -EINVAL;
@@ -868,9 +840,6 @@
dma->rx_cookie = dmaengine_submit(desc);
- dma_sync_single_for_device(dma->rxchan->device->dev, dma->rx_addr,
- dma->rx_size, DMA_FROM_DEVICE);
-
dma_async_issue_pending(dma->rxchan);
out:
spin_unlock_irqrestore(&priv->rx_dma_lock, flags);
@@ -1022,6 +991,18 @@
return ret;
}
+static bool handle_rx_dma(struct uart_8250_port *up, unsigned int iir)
+{
+ switch (iir & 0x3f) {
+ case UART_IIR_RLSI:
+ case UART_IIR_RX_TIMEOUT:
+ case UART_IIR_RDI:
+ omap_8250_rx_dma_flush(up);
+ return true;
+ }
+ return omap_8250_rx_dma(up);
+}
+
/*
* This is mostly serial8250_handle_irq(). We have a slightly different DMA
* hoook for RX/TX and need different logic for them in the ISR. Therefore we
@@ -1033,7 +1014,6 @@
unsigned char status;
unsigned long flags;
u8 iir;
- int dma_err = 0;
serial8250_rpm_get(up);
@@ -1048,11 +1028,9 @@
status = serial_port_in(port, UART_LSR);
if (status & (UART_LSR_DR | UART_LSR_BI)) {
-
- dma_err = omap_8250_rx_dma(up, iir);
- if (dma_err) {
+ if (handle_rx_dma(up, iir)) {
status = serial8250_rx_chars(up, status);
- omap_8250_rx_dma(up, 0);
+ omap_8250_rx_dma(up);
}
}
serial8250_modem_status(up);
@@ -1066,8 +1044,7 @@
* try again due to an earlier failer which
* might have been resolved by now.
*/
- dma_err = omap_8250_tx_dma(up);
- if (dma_err)
+ if (omap_8250_tx_dma(up))
serial8250_tx_chars(up);
}
}
@@ -1084,7 +1061,7 @@
#else
-static inline int omap_8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
+static inline int omap_8250_rx_dma(struct uart_8250_port *p)
{
return -EINVAL;
}
@@ -1395,7 +1372,7 @@
}
if (up->dma && up->dma->rxchan)
- omap_8250_rx_dma(up, UART_IIR_RX_TIMEOUT);
+ omap_8250_rx_dma_flush(up);
priv->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
schedule_work(&priv->qos_work);
@@ -1407,20 +1384,18 @@
{
struct omap8250_priv *priv = dev_get_drvdata(dev);
struct uart_8250_port *up;
- int loss_cntx;
/* In case runtime-pm tries this before we are setup */
if (!priv)
return 0;
up = serial8250_get_port(priv->line);
- loss_cntx = omap8250_lost_context(up);
- if (loss_cntx)
+ if (omap8250_lost_context(up))
omap8250_restore_regs(up);
if (up->dma && up->dma->rxchan)
- omap_8250_rx_dma(up, 0);
+ omap_8250_rx_dma(up);
priv->latency = priv->calc_latency;
schedule_work(&priv->qos_work);
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 5eea74d..8dd250f 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1377,6 +1377,9 @@
unsigned long m, n;
u32 reg;
+ /* Gracefully handle the B0 case: fall back to B9600 */
+ fuart = fuart ? fuart : 9600 * 16;
+
/* Get Fuart closer to Fref */
fuart *= rounddown_pow_of_two(fref / fuart);
@@ -1413,6 +1416,17 @@
return true;
}
+static unsigned int
+byt_get_mctrl(struct uart_port *port)
+{
+ unsigned int ret = serial8250_do_get_mctrl(port);
+
+ /* Force DCD and DSR signals to permanently be reported as active. */
+ ret |= TIOCM_CAR | TIOCM_DSR;
+
+ return ret;
+}
+
static int
byt_serial_setup(struct serial_private *priv,
const struct pciserial_board *board,
@@ -1477,6 +1491,7 @@
port->port.type = PORT_16550A;
port->port.flags = (port->port.flags | UPF_FIXED_PORT | UPF_FIXED_TYPE);
port->port.set_termios = byt_set_termios;
+ port->port.get_mctrl = byt_get_mctrl;
port->port.fifosize = 64;
port->tx_loadsz = 64;
port->dma = dma;
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 00ad263..d403603 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1315,6 +1315,13 @@
out_lock:
spin_unlock_irqrestore(&port->lock, flags);
+
+ /*
+ * Check if the device is a Fintek F81216A
+ */
+ if (port->type == PORT_16550A)
+ fintek_8250_probe(up);
+
if (up->capabilities != old_capabilities) {
pr_warn("ttyS%d: detected caps %08x should be %08x\n",
serial_index(port), old_capabilities,
@@ -1788,6 +1795,18 @@
}
EXPORT_SYMBOL_GPL(serial8250_modem_status);
+static bool handle_rx_dma(struct uart_8250_port *up, unsigned int iir)
+{
+ switch (iir & 0x3f) {
+ case UART_IIR_RX_TIMEOUT:
+ serial8250_rx_dma_flush(up);
+ /* fall-through */
+ case UART_IIR_RLSI:
+ return true;
+ }
+ return up->dma->rx_dma(up);
+}
+
/*
* This handles the interrupt from one port.
*/
@@ -1796,7 +1815,6 @@
unsigned char status;
unsigned long flags;
struct uart_8250_port *up = up_to_u8250p(port);
- int dma_err = 0;
if (iir & UART_IIR_NO_INT)
return 0;
@@ -1808,15 +1826,11 @@
DEBUG_INTR("status = %x...", status);
if (status & (UART_LSR_DR | UART_LSR_BI)) {
- if (up->dma)
- dma_err = up->dma->rx_dma(up, iir);
-
- if (!up->dma || dma_err)
+ if (!up->dma || handle_rx_dma(up, iir))
status = serial8250_rx_chars(up, status);
}
serial8250_modem_status(up);
- if ((!up->dma || (up->dma && up->dma->tx_err)) &&
- (status & UART_LSR_THRE))
+ if ((!up->dma || up->dma->tx_err) && (status & UART_LSR_THRE))
serial8250_tx_chars(up);
spin_unlock_irqrestore(&port->lock, flags);
@@ -1882,7 +1896,7 @@
return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0;
}
-static unsigned int serial8250_get_mctrl(struct uart_port *port)
+unsigned int serial8250_do_get_mctrl(struct uart_port *port)
{
struct uart_8250_port *up = up_to_u8250p(port);
unsigned int status;
@@ -1903,6 +1917,14 @@
ret |= TIOCM_CTS;
return ret;
}
+EXPORT_SYMBOL_GPL(serial8250_do_get_mctrl);
+
+static unsigned int serial8250_get_mctrl(struct uart_port *port)
+{
+ if (port->get_mctrl)
+ return port->get_mctrl(port);
+ return serial8250_do_get_mctrl(port);
+}
void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
diff --git a/drivers/tty/serial/8250/8250_uniphier.c b/drivers/tty/serial/8250/8250_uniphier.c
index 1b7bd26..efd1f9c 100644
--- a/drivers/tty/serial/8250/8250_uniphier.c
+++ b/drivers/tty/serial/8250/8250_uniphier.c
@@ -209,7 +209,7 @@
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
- dev_err(dev, "failed to get IRQ number");
+ dev_err(dev, "failed to get IRQ number\n");
return irq;
}
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index 4d7cb9c..e46761d 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -57,6 +57,18 @@
This builds standard PNP serial support. You may be able to
disable this feature if you only need legacy serial support.
+config SERIAL_8250_FINTEK
+ bool "Support for Fintek F81216A LPC to 4 UART RS485 API"
+ depends on SERIAL_8250
+ ---help---
+ Selecting this option will add support for the RS485 capabilities
+ of the Fintek F81216A LPC to 4 UART.
+
+ If this option is not selected the device will be configured as a
+ standard 16550A serial port.
+
+ If unsure, say N.
+
config SERIAL_8250_CONSOLE
bool "Console on 8250/16550 and compatible serial port"
depends on SERIAL_8250=y
@@ -358,14 +370,6 @@
not booting kernel because the serial console remains silent in case
they forgot to update the command line.
-config SERIAL_8250_FINTEK
- tristate "Support for Fintek F81216A LPC to 4 UART"
- depends on SERIAL_8250 && PNP
- help
- Selecting this option will add support for the Fintek F81216A
- LPC to 4 UART. This device has some RS485 functionality not available
- through the PNP driver. If unsure, say N.
-
config SERIAL_8250_LPC18XX
tristate "NXP LPC18xx/43xx serial port support"
depends on SERIAL_8250 && OF && (ARCH_LPC18XX || COMPILE_TEST)
@@ -398,8 +402,10 @@
its UARTs, say Y to this option. If unsure, say N.
config SERIAL_8250_MID
- tristate "Support for serial ports on Intel MID platforms"
+ tristate "Support for serial ports on Intel MID platforms" if EXPERT
+ default SERIAL_8250
depends on SERIAL_8250 && PCI
+ depends on X86 || COMPILE_TEST
select HSU_DMA if SERIAL_8250_DMA
select HSU_DMA_PCI if (HSU_DMA && X86_INTEL_MID)
select RATIONAL
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index c9a2d6e..367d403 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -7,6 +7,7 @@
8250-$(CONFIG_SERIAL_8250_PNP) += 8250_pnp.o
8250_base-y := 8250_port.o
8250_base-$(CONFIG_SERIAL_8250_DMA) += 8250_dma.o
+8250_base-$(CONFIG_SERIAL_8250_FINTEK) += 8250_fintek.o
obj-$(CONFIG_SERIAL_8250_GSC) += 8250_gsc.o
obj-$(CONFIG_SERIAL_8250_PCI) += 8250_pci.o
obj-$(CONFIG_SERIAL_8250_HP300) += 8250_hp300.o
@@ -23,7 +24,6 @@
obj-$(CONFIG_SERIAL_8250_DW) += 8250_dw.o
obj-$(CONFIG_SERIAL_8250_EM) += 8250_em.o
obj-$(CONFIG_SERIAL_8250_OMAP) += 8250_omap.o
-obj-$(CONFIG_SERIAL_8250_FINTEK) += 8250_fintek.o
obj-$(CONFIG_SERIAL_8250_LPC18XX) += 8250_lpc18xx.o
obj-$(CONFIG_SERIAL_8250_MT6577) += 8250_mtk.o
obj-$(CONFIG_SERIAL_8250_UNIPHIER) += 8250_uniphier.o
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 7711b26..7e3a58c 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -213,6 +213,7 @@
bool "Support for console on meson"
depends on SERIAL_MESON=y
select SERIAL_CORE_CONSOLE
+ select SERIAL_EARLYCON
help
Say Y here if you wish to use a Amlogic MesonX UART as the
system console (the system console is the device which
@@ -1404,11 +1405,12 @@
config SERIAL_MXS_AUART
tristate "MXS AUART support"
depends on HAS_DMA
- depends on ARCH_MXS || COMPILE_TEST
+ depends on ARCH_MXS || MACH_ASM9260 || COMPILE_TEST
select SERIAL_CORE
select SERIAL_MCTRL_GPIO if GPIOLIB
help
- This driver supports the MXS Application UART (AUART) port.
+ This driver supports the MXS and Alphascale ASM9260 Application
+ UART (AUART) port.
config SERIAL_MXS_AUART_CONSOLE
bool "MXS AUART console support"
@@ -1467,6 +1469,19 @@
This driver support the USART and UART ports on
Energy Micro's efm32 SoCs.
+config SERIAL_MPS2_UART_CONSOLE
+ bool "MPS2 UART console support"
+ depends on SERIAL_MPS2_UART
+ select SERIAL_CORE_CONSOLE
+ select SERIAL_EARLYCON
+
+config SERIAL_MPS2_UART
+ bool "MPS2 UART port"
+ depends on ARM || COMPILE_TEST
+ select SERIAL_CORE
+ help
+ This driver support the UART ports on ARM MPS2.
+
config SERIAL_EFM32_UART_CONSOLE
bool "EFM32 UART/USART console support"
depends on SERIAL_EFM32_UART=y
@@ -1625,6 +1640,7 @@
config SERIAL_MVEBU_UART
bool "Marvell EBU serial port support"
+ depends on ARCH_MVEBU || COMPILE_TEST
select SERIAL_CORE
help
This driver is for Marvell EBU SoC's UART. If you have a machine
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index 74914aa..1278d37 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -92,6 +92,7 @@
obj-$(CONFIG_SERIAL_STM32) += stm32-usart.o
obj-$(CONFIG_SERIAL_MVEBU_UART) += mvebu-uart.o
obj-$(CONFIG_SERIAL_PIC32) += pic32_uart.o
+obj-$(CONFIG_SERIAL_MPS2_UART) += mps2-uart.o
# GPIOLIB helpers for modem control lines
obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index 7c198e0..a2aa655 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -121,6 +121,7 @@
static struct vendor_data vendor_sbsa = {
.reg_offset = pl011_std_offsets,
+ .access_32b = true,
.oversampling = false,
.dma_threshold = false,
.cts_event_workaround = false,
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index d9439e6..954941d 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -274,6 +274,13 @@
return atmel_port->use_dma_rx;
}
+static bool atmel_use_fifo(struct uart_port *port)
+{
+ struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
+
+ return atmel_port->fifo_size;
+}
+
static unsigned int atmel_get_lines_status(struct uart_port *port)
{
struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
@@ -2090,7 +2097,12 @@
mode |= ATMEL_US_USMODE_RS485;
} else if (termios->c_cflag & CRTSCTS) {
/* RS232 with hardware handshake (RTS/CTS) */
- mode |= ATMEL_US_USMODE_HWHS;
+ if (atmel_use_dma_rx(port) && !atmel_use_fifo(port)) {
+ dev_info(port->dev, "not enabling hardware flow control because DMA is used");
+ termios->c_cflag &= ~CRTSCTS;
+ } else {
+ mode |= ATMEL_US_USMODE_HWHS;
+ }
} else {
/* RS232 without hadware handshake */
mode |= ATMEL_US_USMODE_NORMAL;
diff --git a/drivers/tty/serial/crisv10.c b/drivers/tty/serial/crisv10.c
index c0172bf54..315c849 100644
--- a/drivers/tty/serial/crisv10.c
+++ b/drivers/tty/serial/crisv10.c
@@ -2599,7 +2599,7 @@
/* if it was already initialized, skip this */
- if (info->port.flags & ASYNC_INITIALIZED) {
+ if (tty_port_initialized(&info->port)) {
local_irq_restore(flags);
free_page(xmit_page);
return 0;
@@ -2703,7 +2703,7 @@
e100_rts(info, 1);
e100_dtr(info, 1);
- info->port.flags |= ASYNC_INITIALIZED;
+ tty_port_set_initialized(&info->port, 1);
local_irq_restore(flags);
return 0;
@@ -2745,7 +2745,7 @@
info->tr_running = 0;
}
- if (!(info->port.flags & ASYNC_INITIALIZED))
+ if (!tty_port_initialized(&info->port))
return;
#ifdef SERIAL_DEBUG_OPEN
@@ -2776,7 +2776,7 @@
if (info->port.tty)
set_bit(TTY_IO_ERROR, &info->port.tty->flags);
- info->port.flags &= ~ASYNC_INITIALIZED;
+ tty_port_set_initialized(&info->port, 0);
local_irq_restore(flags);
}
@@ -3273,9 +3273,9 @@
info->port.low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
check_and_exit:
- if (info->port.flags & ASYNC_INITIALIZED) {
+ if (tty_port_initialized(&info->port))
change_speed(info);
- } else
+ else
retval = startup(info);
return retval;
}
@@ -3445,7 +3445,7 @@
if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
(cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD) &&
(cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT)) {
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
}
@@ -3628,7 +3628,7 @@
e100_disable_rx(info);
e100_disable_rx_irq(info);
- if (info->port.flags & ASYNC_INITIALIZED) {
+ if (tty_port_initialized(&info->port)) {
/*
* Before we drop DTR, make sure the UART transmitter
* has completely drained; this is especially
@@ -3648,8 +3648,8 @@
schedule_timeout_interruptible(info->port.close_delay);
wake_up_interruptible(&info->port.open_wait);
}
- info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
local_irq_restore(flags);
+ tty_port_set_active(&info->port, 0);
/* port closed */
@@ -3732,7 +3732,7 @@
shutdown(info);
info->event = 0;
info->port.count = 0;
- info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
+ tty_port_set_active(&info->port, 0);
info->port.tty = NULL;
wake_up_interruptible(&info->port.open_wait);
}
@@ -3755,9 +3755,8 @@
* If non-blocking mode is set, or the port is not enabled,
* then make the check up front and then exit.
*/
- if ((filp->f_flags & O_NONBLOCK) ||
- (tty->flags & (1 << TTY_IO_ERROR))) {
- info->port.flags |= ASYNC_NORMAL_ACTIVE;
+ if ((filp->f_flags & O_NONBLOCK) || tty_io_error(tty)) {
+ tty_port_set_active(&info->port, 1);
return 0;
}
@@ -3788,8 +3787,7 @@
e100_dtr(info, 1);
local_irq_restore(flags);
set_current_state(TASK_INTERRUPTIBLE);
- if (tty_hung_up_p(filp) ||
- !(info->port.flags & ASYNC_INITIALIZED)) {
+ if (tty_hung_up_p(filp) || !tty_port_initialized(&info->port)) {
#ifdef SERIAL_DO_RESTART
if (info->port.flags & ASYNC_HUP_NOTIFY)
retval = -EAGAIN;
@@ -3826,7 +3824,7 @@
#endif
if (retval)
return retval;
- info->port.flags |= ASYNC_NORMAL_ACTIVE;
+ tty_port_set_active(&info->port, 1);
return 0;
}
diff --git a/drivers/tty/serial/ifx6x60.c b/drivers/tty/serial/ifx6x60.c
index 2085a6c..d386346 100644
--- a/drivers/tty/serial/ifx6x60.c
+++ b/drivers/tty/serial/ifx6x60.c
@@ -651,7 +651,7 @@
struct ifx_spi_device *ifx_dev = ctx;
int length;
int actual_length;
- unsigned char more;
+ unsigned char more = 0;
unsigned char cts;
int local_write_pending = 0;
int queue_length;
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 231e7d5..0df2b1c 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -114,6 +114,7 @@
#define UCR3_RXDSEN (1<<6) /* Receive status interrupt enable */
#define UCR3_AIRINTEN (1<<5) /* Async IR wake interrupt enable */
#define UCR3_AWAKEN (1<<4) /* Async wake interrupt enable */
+#define UCR3_DTRDEN (1<<3) /* Data Terminal Ready Delta Enable. */
#define IMX21_UCR3_RXDMUXSEL (1<<2) /* RXD Muxed Input Select */
#define UCR3_INVT (1<<1) /* Inverted Infrared transmission */
#define UCR3_BPEN (1<<0) /* Preset registers enable */
@@ -142,7 +143,7 @@
#define USR1_FRAMERR (1<<10) /* Frame error interrupt flag */
#define USR1_RRDY (1<<9) /* Receiver ready interrupt/dma flag */
#define USR1_AGTIM (1<<8) /* Ageing timer interrupt flag */
-#define USR1_TIMEOUT (1<<7) /* Receive timeout interrupt status */
+#define USR1_DTRD (1<<7) /* DTR Delta */
#define USR1_RXDS (1<<6) /* Receiver idle interrupt flag */
#define USR1_AIRINT (1<<5) /* Async IR wake interrupt flag */
#define USR1_AWAKE (1<<4) /* Aysnc wake interrupt flag */
@@ -361,6 +362,7 @@
imx_port_rts_inactive(sport, &temp);
else
imx_port_rts_active(sport, &temp);
+ temp |= UCR2_RXEN;
writel(temp, port->membase + UCR2);
temp = readl(port->membase + UCR4);
@@ -568,6 +570,8 @@
imx_port_rts_inactive(sport, &temp);
else
imx_port_rts_active(sport, &temp);
+ if (!(port->rs485.flags & SER_RS485_RX_DURING_TX))
+ temp &= ~UCR2_RXEN;
writel(temp, port->membase + UCR2);
/* enable transmitter and shifter empty irq */
@@ -729,11 +733,61 @@
spin_unlock_irqrestore(&sport->port.lock, flags);
}
+/*
+ * We have a modem side uart, so the meanings of RTS and CTS are inverted.
+ */
+static unsigned int imx_get_hwmctrl(struct imx_port *sport)
+{
+ unsigned int tmp = TIOCM_DSR;
+ unsigned usr1 = readl(sport->port.membase + USR1);
+
+ if (usr1 & USR1_RTSS)
+ tmp |= TIOCM_CTS;
+
+ /* in DCE mode DCDIN is always 0 */
+ if (!(usr1 & USR2_DCDIN))
+ tmp |= TIOCM_CAR;
+
+ if (sport->dte_mode)
+ if (!(readl(sport->port.membase + USR2) & USR2_RIIN))
+ tmp |= TIOCM_RI;
+
+ return tmp;
+}
+
+/*
+ * Handle any change of modem status signal since we were last called.
+ */
+static void imx_mctrl_check(struct imx_port *sport)
+{
+ unsigned int status, changed;
+
+ status = imx_get_hwmctrl(sport);
+ changed = status ^ sport->old_status;
+
+ if (changed == 0)
+ return;
+
+ sport->old_status = status;
+
+ if (changed & TIOCM_RI && status & TIOCM_RI)
+ sport->port.icount.rng++;
+ if (changed & TIOCM_DSR)
+ sport->port.icount.dsr++;
+ if (changed & TIOCM_CAR)
+ uart_handle_dcd_change(&sport->port, status & TIOCM_CAR);
+ if (changed & TIOCM_CTS)
+ uart_handle_cts_change(&sport->port, status & TIOCM_CTS);
+
+ wake_up_interruptible(&sport->port.state->port.delta_msr_wait);
+}
+
static irqreturn_t imx_int(int irq, void *dev_id)
{
struct imx_port *sport = dev_id;
unsigned int sts;
unsigned int sts2;
+ irqreturn_t ret = IRQ_NONE;
sts = readl(sport->port.membase + USR1);
sts2 = readl(sport->port.membase + USR2);
@@ -743,26 +797,47 @@
imx_dma_rxint(sport);
else
imx_rxint(irq, dev_id);
+ ret = IRQ_HANDLED;
}
if ((sts & USR1_TRDY &&
readl(sport->port.membase + UCR1) & UCR1_TXMPTYEN) ||
(sts2 & USR2_TXDC &&
- readl(sport->port.membase + UCR4) & UCR4_TCEN))
+ readl(sport->port.membase + UCR4) & UCR4_TCEN)) {
imx_txint(irq, dev_id);
+ ret = IRQ_HANDLED;
+ }
- if (sts & USR1_RTSD)
+ if (sts & USR1_DTRD) {
+ unsigned long flags;
+
+ if (sts & USR1_DTRD)
+ writel(USR1_DTRD, sport->port.membase + USR1);
+
+ spin_lock_irqsave(&sport->port.lock, flags);
+ imx_mctrl_check(sport);
+ spin_unlock_irqrestore(&sport->port.lock, flags);
+
+ ret = IRQ_HANDLED;
+ }
+
+ if (sts & USR1_RTSD) {
imx_rtsint(irq, dev_id);
+ ret = IRQ_HANDLED;
+ }
- if (sts & USR1_AWAKE)
+ if (sts & USR1_AWAKE) {
writel(USR1_AWAKE, sport->port.membase + USR1);
+ ret = IRQ_HANDLED;
+ }
if (sts2 & USR2_ORE) {
sport->port.icount.overrun++;
writel(USR2_ORE, sport->port.membase + USR2);
+ ret = IRQ_HANDLED;
}
- return IRQ_HANDLED;
+ return ret;
}
/*
@@ -782,28 +857,6 @@
return ret;
}
-/*
- * We have a modem side uart, so the meanings of RTS and CTS are inverted.
- */
-static unsigned int imx_get_hwmctrl(struct imx_port *sport)
-{
- unsigned int tmp = TIOCM_DSR;
- unsigned usr1 = readl(sport->port.membase + USR1);
-
- if (usr1 & USR1_RTSS)
- tmp |= TIOCM_CTS;
-
- /* in DCE mode DCDIN is always 0 */
- if (!(usr1 & USR2_DCDIN))
- tmp |= TIOCM_CAR;
-
- /* in DCE mode RIIN is always 0 */
- if (readl(sport->port.membase + USR2) & USR2_RIIN)
- tmp |= TIOCM_RI;
-
- return tmp;
-}
-
static unsigned int imx_get_mctrl(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
@@ -861,33 +914,6 @@
}
/*
- * Handle any change of modem status signal since we were last called.
- */
-static void imx_mctrl_check(struct imx_port *sport)
-{
- unsigned int status, changed;
-
- status = imx_get_hwmctrl(sport);
- changed = status ^ sport->old_status;
-
- if (changed == 0)
- return;
-
- sport->old_status = status;
-
- if (changed & TIOCM_RI)
- sport->port.icount.rng++;
- if (changed & TIOCM_DSR)
- sport->port.icount.dsr++;
- if (changed & TIOCM_CAR)
- uart_handle_dcd_change(&sport->port, status & TIOCM_CAR);
- if (changed & TIOCM_CTS)
- uart_handle_cts_change(&sport->port, status & TIOCM_CTS);
-
- wake_up_interruptible(&sport->port.state->port.delta_msr_wait);
-}
-
-/*
* This is our per-port timeout handler, for checking the
* modem status signals.
*/
@@ -1193,7 +1219,7 @@
/*
* Finally, clear and enable interrupts
*/
- writel(USR1_RTSD, sport->port.membase + USR1);
+ writel(USR1_RTSD | USR1_DTRD, sport->port.membase + USR1);
writel(USR2_ORE, sport->port.membase + USR2);
if (sport->dma_is_inited && !sport->dma_is_enabled)
@@ -1212,11 +1238,32 @@
temp |= (UCR2_RXEN | UCR2_TXEN);
if (!sport->have_rtscts)
temp |= UCR2_IRTS;
+ /*
+ * make sure the edge sensitive RTS-irq is disabled,
+ * we're using RTSD instead.
+ */
+ if (!is_imx1_uart(sport))
+ temp &= ~UCR2_RTSEN;
writel(temp, sport->port.membase + UCR2);
if (!is_imx1_uart(sport)) {
temp = readl(sport->port.membase + UCR3);
- temp |= IMX21_UCR3_RXDMUXSEL | UCR3_ADNIMP;
+
+ /*
+ * The effect of RI and DCD differs depending on the UFCR_DCEDTE
+ * bit. In DCE mode they control the outputs, in DTE mode they
+ * enable the respective irqs. At least the DCD irq cannot be
+ * cleared on i.MX25 at least, so it's not usable and must be
+ * disabled. I don't have test hardware to check if RI has the
+ * same problem but I consider this likely so it's disabled for
+ * now, too.
+ */
+ temp |= IMX21_UCR3_RXDMUXSEL | UCR3_ADNIMP |
+ UCR3_DTRDEN | UCR3_RI | UCR3_DCD;
+
+ if (sport->dte_mode)
+ temp &= ~(UCR3_RI | UCR3_DCD);
+
writel(temp, sport->port.membase + UCR3);
}
@@ -1610,19 +1657,17 @@
struct serial_rs485 *rs485conf)
{
struct imx_port *sport = (struct imx_port *)port;
+ unsigned long temp;
/* unimplemented */
rs485conf->delay_rts_before_send = 0;
rs485conf->delay_rts_after_send = 0;
- rs485conf->flags |= SER_RS485_RX_DURING_TX;
/* RTS is required to control the transmitter */
if (!sport->have_rtscts)
rs485conf->flags &= ~SER_RS485_ENABLED;
if (rs485conf->flags & SER_RS485_ENABLED) {
- unsigned long temp;
-
/* disable transmitter */
temp = readl(sport->port.membase + UCR2);
if (rs485conf->flags & SER_RS485_RTS_AFTER_SEND)
@@ -1632,6 +1677,14 @@
writel(temp, sport->port.membase + UCR2);
}
+ /* Make sure Rx is enabled in case Tx is active with Rx disabled */
+ if (!(rs485conf->flags & SER_RS485_ENABLED) ||
+ rs485conf->flags & SER_RS485_RX_DURING_TX) {
+ temp = readl(sport->port.membase + UCR2);
+ temp |= UCR2_RXEN;
+ writel(temp, sport->port.membase + UCR2);
+ }
+
port->rs485 = *rs485conf;
return 0;
@@ -1927,7 +1980,8 @@
}
sport->port.line = ret;
- if (of_get_property(np, "fsl,uart-has-rtscts", NULL))
+ if (of_get_property(np, "uart-has-rtscts", NULL) ||
+ of_get_property(np, "fsl,uart-has-rtscts", NULL) /* deprecated */)
sport->have_rtscts = 1;
if (of_get_property(np, "fsl,dte-mode", NULL))
diff --git a/drivers/tty/serial/meson_uart.c b/drivers/tty/serial/meson_uart.c
index 024445a..6aea0f4 100644
--- a/drivers/tty/serial/meson_uart.c
+++ b/drivers/tty/serial/meson_uart.c
@@ -481,18 +481,13 @@
writel(ch, port->membase + AML_UART_WFIFO);
}
-static void meson_serial_console_write(struct console *co, const char *s,
- u_int count)
+static void meson_serial_port_write(struct uart_port *port, const char *s,
+ u_int count)
{
- struct uart_port *port;
unsigned long flags;
int locked;
u32 val, tmp;
- port = meson_ports[co->index];
- if (!port)
- return;
-
local_irq_save(flags);
if (port->sysrq) {
locked = 0;
@@ -516,6 +511,18 @@
local_irq_restore(flags);
}
+static void meson_serial_console_write(struct console *co, const char *s,
+ u_int count)
+{
+ struct uart_port *port;
+
+ port = meson_ports[co->index];
+ if (!port)
+ return;
+
+ meson_serial_port_write(port, s, count);
+}
+
static int meson_serial_console_setup(struct console *co, char *options)
{
struct uart_port *port;
@@ -554,6 +561,27 @@
}
console_initcall(meson_serial_console_init);
+static void meson_serial_early_console_write(struct console *co,
+ const char *s,
+ u_int count)
+{
+ struct earlycon_device *dev = co->data;
+
+ meson_serial_port_write(&dev->port, s, count);
+}
+
+static int __init
+meson_serial_early_console_setup(struct earlycon_device *device, const char *opt)
+{
+ if (!device->port.membase)
+ return -ENODEV;
+
+ device->con->write = meson_serial_early_console_write;
+ return 0;
+}
+OF_EARLYCON_DECLARE(meson, "amlogic,meson-uart",
+ meson_serial_early_console_setup);
+
#define MESON_SERIAL_CONSOLE (&meson_serial_console)
#else
#define MESON_SERIAL_CONSOLE NULL
diff --git a/drivers/tty/serial/mps2-uart.c b/drivers/tty/serial/mps2-uart.c
new file mode 100644
index 0000000..da9e27d
--- /dev/null
+++ b/drivers/tty/serial/mps2-uart.c
@@ -0,0 +1,625 @@
+/*
+ * Copyright (C) 2015 ARM Limited
+ *
+ * Author: Vladimir Murzin <vladimir.murzin@arm.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * TODO: support for SysRq
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/console.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/serial_core.h>
+#include <linux/tty_flip.h>
+#include <linux/types.h>
+
+#define SERIAL_NAME "ttyMPS"
+#define DRIVER_NAME "mps2-uart"
+#define MAKE_NAME(x) (DRIVER_NAME # x)
+
+#define UARTn_DATA 0x00
+
+#define UARTn_STATE 0x04
+#define UARTn_STATE_TX_FULL BIT(0)
+#define UARTn_STATE_RX_FULL BIT(1)
+#define UARTn_STATE_TX_OVERRUN BIT(2)
+#define UARTn_STATE_RX_OVERRUN BIT(3)
+
+#define UARTn_CTRL 0x08
+#define UARTn_CTRL_TX_ENABLE BIT(0)
+#define UARTn_CTRL_RX_ENABLE BIT(1)
+#define UARTn_CTRL_TX_INT_ENABLE BIT(2)
+#define UARTn_CTRL_RX_INT_ENABLE BIT(3)
+#define UARTn_CTRL_TX_OVERRUN_INT_ENABLE BIT(4)
+#define UARTn_CTRL_RX_OVERRUN_INT_ENABLE BIT(5)
+
+#define UARTn_INT 0x0c
+#define UARTn_INT_TX BIT(0)
+#define UARTn_INT_RX BIT(1)
+#define UARTn_INT_TX_OVERRUN BIT(2)
+#define UARTn_INT_RX_OVERRUN BIT(3)
+
+#define UARTn_BAUDDIV 0x10
+#define UARTn_BAUDDIV_MASK GENMASK(20, 0)
+
+/*
+ * Helpers to make typical enable/disable operations more readable.
+ */
+#define UARTn_CTRL_TX_GRP (UARTn_CTRL_TX_ENABLE |\
+ UARTn_CTRL_TX_INT_ENABLE |\
+ UARTn_CTRL_TX_OVERRUN_INT_ENABLE)
+
+#define UARTn_CTRL_RX_GRP (UARTn_CTRL_RX_ENABLE |\
+ UARTn_CTRL_RX_INT_ENABLE |\
+ UARTn_CTRL_RX_OVERRUN_INT_ENABLE)
+
+#define MPS2_MAX_PORTS 3
+
+struct mps2_uart_port {
+ struct uart_port port;
+ struct clk *clk;
+ unsigned int tx_irq;
+ unsigned int rx_irq;
+};
+
+static inline struct mps2_uart_port *to_mps2_port(struct uart_port *port)
+{
+ return container_of(port, struct mps2_uart_port, port);
+}
+
+static void mps2_uart_write8(struct uart_port *port, u8 val, unsigned int off)
+{
+ struct mps2_uart_port *mps_port = to_mps2_port(port);
+
+ writeb(val, mps_port->port.membase + off);
+}
+
+static u8 mps2_uart_read8(struct uart_port *port, unsigned int off)
+{
+ struct mps2_uart_port *mps_port = to_mps2_port(port);
+
+ return readb(mps_port->port.membase + off);
+}
+
+static void mps2_uart_write32(struct uart_port *port, u32 val, unsigned int off)
+{
+ struct mps2_uart_port *mps_port = to_mps2_port(port);
+
+ writel_relaxed(val, mps_port->port.membase + off);
+}
+
+static unsigned int mps2_uart_tx_empty(struct uart_port *port)
+{
+ u8 status = mps2_uart_read8(port, UARTn_STATE);
+
+ return (status & UARTn_STATE_TX_FULL) ? 0 : TIOCSER_TEMT;
+}
+
+static void mps2_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+
+static unsigned int mps2_uart_get_mctrl(struct uart_port *port)
+{
+ return TIOCM_CAR | TIOCM_CTS | TIOCM_DSR;
+}
+
+static void mps2_uart_stop_tx(struct uart_port *port)
+{
+ u8 control = mps2_uart_read8(port, UARTn_CTRL);
+
+ control &= ~UARTn_CTRL_TX_INT_ENABLE;
+
+ mps2_uart_write8(port, control, UARTn_CTRL);
+}
+
+static void mps2_uart_tx_chars(struct uart_port *port)
+{
+ struct circ_buf *xmit = &port->state->xmit;
+
+ while (!(mps2_uart_read8(port, UARTn_STATE) & UARTn_STATE_TX_FULL)) {
+ if (port->x_char) {
+ mps2_uart_write8(port, port->x_char, UARTn_DATA);
+ port->x_char = 0;
+ port->icount.tx++;
+ continue;
+ }
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(port))
+ break;
+
+ mps2_uart_write8(port, xmit->buf[xmit->tail], UARTn_DATA);
+ xmit->tail = (xmit->tail + 1) % UART_XMIT_SIZE;
+ port->icount.tx++;
+ }
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+
+ if (uart_circ_empty(xmit))
+ mps2_uart_stop_tx(port);
+}
+
+static void mps2_uart_start_tx(struct uart_port *port)
+{
+ u8 control = mps2_uart_read8(port, UARTn_CTRL);
+
+ control |= UARTn_CTRL_TX_INT_ENABLE;
+
+ mps2_uart_write8(port, control, UARTn_CTRL);
+
+ /*
+ * We've just unmasked the TX IRQ and now slow-starting via
+ * polling; if there is enough data to fill up the internal
+ * write buffer in one go, the TX IRQ should assert, at which
+ * point we switch to fully interrupt-driven TX.
+ */
+
+ mps2_uart_tx_chars(port);
+}
+
+static void mps2_uart_stop_rx(struct uart_port *port)
+{
+ u8 control = mps2_uart_read8(port, UARTn_CTRL);
+
+ control &= ~UARTn_CTRL_RX_GRP;
+
+ mps2_uart_write8(port, control, UARTn_CTRL);
+}
+
+static void mps2_uart_break_ctl(struct uart_port *port, int ctl)
+{
+}
+
+static void mps2_uart_rx_chars(struct uart_port *port)
+{
+ struct tty_port *tport = &port->state->port;
+
+ while (mps2_uart_read8(port, UARTn_STATE) & UARTn_STATE_RX_FULL) {
+ u8 rxdata = mps2_uart_read8(port, UARTn_DATA);
+
+ port->icount.rx++;
+ tty_insert_flip_char(&port->state->port, rxdata, TTY_NORMAL);
+ }
+
+ tty_flip_buffer_push(tport);
+}
+
+static irqreturn_t mps2_uart_rxirq(int irq, void *data)
+{
+ struct uart_port *port = data;
+ u8 irqflag = mps2_uart_read8(port, UARTn_INT);
+
+ if (unlikely(!(irqflag & UARTn_INT_RX)))
+ return IRQ_NONE;
+
+ spin_lock(&port->lock);
+
+ mps2_uart_write8(port, UARTn_INT_RX, UARTn_INT);
+ mps2_uart_rx_chars(port);
+
+ spin_unlock(&port->lock);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t mps2_uart_txirq(int irq, void *data)
+{
+ struct uart_port *port = data;
+ u8 irqflag = mps2_uart_read8(port, UARTn_INT);
+
+ if (unlikely(!(irqflag & UARTn_INT_TX)))
+ return IRQ_NONE;
+
+ spin_lock(&port->lock);
+
+ mps2_uart_write8(port, UARTn_INT_TX, UARTn_INT);
+ mps2_uart_tx_chars(port);
+
+ spin_unlock(&port->lock);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t mps2_uart_oerrirq(int irq, void *data)
+{
+ irqreturn_t handled = IRQ_NONE;
+ struct uart_port *port = data;
+ u8 irqflag = mps2_uart_read8(port, UARTn_INT);
+
+ spin_lock(&port->lock);
+
+ if (irqflag & UARTn_INT_RX_OVERRUN) {
+ struct tty_port *tport = &port->state->port;
+
+ mps2_uart_write8(port, UARTn_INT_RX_OVERRUN, UARTn_INT);
+ port->icount.overrun++;
+ tty_insert_flip_char(tport, 0, TTY_OVERRUN);
+ tty_flip_buffer_push(tport);
+ handled = IRQ_HANDLED;
+ }
+
+ /*
+ * It's never been seen in practice and it never *should* happen since
+ * we check if there is enough room in TX buffer before sending data.
+ * So we keep this check in case something suspicious has happened.
+ */
+ if (irqflag & UARTn_INT_TX_OVERRUN) {
+ mps2_uart_write8(port, UARTn_INT_TX_OVERRUN, UARTn_INT);
+ handled = IRQ_HANDLED;
+ }
+
+ spin_unlock(&port->lock);
+
+ return handled;
+}
+
+static int mps2_uart_startup(struct uart_port *port)
+{
+ struct mps2_uart_port *mps_port = to_mps2_port(port);
+ u8 control = mps2_uart_read8(port, UARTn_CTRL);
+ int ret;
+
+ control &= ~(UARTn_CTRL_RX_GRP | UARTn_CTRL_TX_GRP);
+
+ mps2_uart_write8(port, control, UARTn_CTRL);
+
+ ret = request_irq(mps_port->rx_irq, mps2_uart_rxirq, 0,
+ MAKE_NAME(-rx), mps_port);
+ if (ret) {
+ dev_err(port->dev, "failed to register rxirq (%d)\n", ret);
+ return ret;
+ }
+
+ ret = request_irq(mps_port->tx_irq, mps2_uart_txirq, 0,
+ MAKE_NAME(-tx), mps_port);
+ if (ret) {
+ dev_err(port->dev, "failed to register txirq (%d)\n", ret);
+ goto err_free_rxirq;
+ }
+
+ ret = request_irq(port->irq, mps2_uart_oerrirq, IRQF_SHARED,
+ MAKE_NAME(-overrun), mps_port);
+
+ if (ret) {
+ dev_err(port->dev, "failed to register oerrirq (%d)\n", ret);
+ goto err_free_txirq;
+ }
+
+ control |= UARTn_CTRL_RX_GRP | UARTn_CTRL_TX_GRP;
+
+ mps2_uart_write8(port, control, UARTn_CTRL);
+
+ return 0;
+
+err_free_txirq:
+ free_irq(mps_port->tx_irq, mps_port);
+err_free_rxirq:
+ free_irq(mps_port->rx_irq, mps_port);
+
+ return ret;
+}
+
+static void mps2_uart_shutdown(struct uart_port *port)
+{
+ struct mps2_uart_port *mps_port = to_mps2_port(port);
+ u8 control = mps2_uart_read8(port, UARTn_CTRL);
+
+ control &= ~(UARTn_CTRL_RX_GRP | UARTn_CTRL_TX_GRP);
+
+ mps2_uart_write8(port, control, UARTn_CTRL);
+
+ free_irq(mps_port->rx_irq, mps_port);
+ free_irq(mps_port->tx_irq, mps_port);
+ free_irq(port->irq, mps_port);
+}
+
+static void
+mps2_uart_set_termios(struct uart_port *port, struct ktermios *termios,
+ struct ktermios *old)
+{
+ unsigned long flags;
+ unsigned int baud, bauddiv;
+
+ termios->c_cflag &= ~(CRTSCTS | CMSPAR);
+ termios->c_cflag &= ~CSIZE;
+ termios->c_cflag |= CS8;
+ termios->c_cflag &= ~PARENB;
+ termios->c_cflag &= ~CSTOPB;
+
+ baud = uart_get_baud_rate(port, termios, old,
+ DIV_ROUND_CLOSEST(port->uartclk, UARTn_BAUDDIV_MASK),
+ DIV_ROUND_CLOSEST(port->uartclk, 16));
+
+ bauddiv = DIV_ROUND_CLOSEST(port->uartclk, baud);
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ uart_update_timeout(port, termios->c_cflag, baud);
+ mps2_uart_write32(port, bauddiv, UARTn_BAUDDIV);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ if (tty_termios_baud_rate(termios))
+ tty_termios_encode_baud_rate(termios, baud, baud);
+}
+
+static const char *mps2_uart_type(struct uart_port *port)
+{
+ return (port->type == PORT_MPS2UART) ? DRIVER_NAME : NULL;
+}
+
+static void mps2_uart_release_port(struct uart_port *port)
+{
+}
+
+static int mps2_uart_request_port(struct uart_port *port)
+{
+ return 0;
+}
+
+static void mps2_uart_config_port(struct uart_port *port, int type)
+{
+ if (type & UART_CONFIG_TYPE && !mps2_uart_request_port(port))
+ port->type = PORT_MPS2UART;
+}
+
+static int mps2_uart_verify_port(struct uart_port *port, struct serial_struct *serinfo)
+{
+ return -EINVAL;
+}
+
+static const struct uart_ops mps2_uart_pops = {
+ .tx_empty = mps2_uart_tx_empty,
+ .set_mctrl = mps2_uart_set_mctrl,
+ .get_mctrl = mps2_uart_get_mctrl,
+ .stop_tx = mps2_uart_stop_tx,
+ .start_tx = mps2_uart_start_tx,
+ .stop_rx = mps2_uart_stop_rx,
+ .break_ctl = mps2_uart_break_ctl,
+ .startup = mps2_uart_startup,
+ .shutdown = mps2_uart_shutdown,
+ .set_termios = mps2_uart_set_termios,
+ .type = mps2_uart_type,
+ .release_port = mps2_uart_release_port,
+ .request_port = mps2_uart_request_port,
+ .config_port = mps2_uart_config_port,
+ .verify_port = mps2_uart_verify_port,
+};
+
+static struct mps2_uart_port mps2_uart_ports[MPS2_MAX_PORTS];
+
+#ifdef CONFIG_SERIAL_MPS2_UART_CONSOLE
+static void mps2_uart_console_putchar(struct uart_port *port, int ch)
+{
+ while (mps2_uart_read8(port, UARTn_STATE) & UARTn_STATE_TX_FULL)
+ cpu_relax();
+
+ mps2_uart_write8(port, ch, UARTn_DATA);
+}
+
+static void mps2_uart_console_write(struct console *co, const char *s, unsigned int cnt)
+{
+ struct uart_port *port = &mps2_uart_ports[co->index].port;
+
+ uart_console_write(port, s, cnt, mps2_uart_console_putchar);
+}
+
+static int mps2_uart_console_setup(struct console *co, char *options)
+{
+ struct mps2_uart_port *mps_port;
+ int baud = 9600;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if (co->index < 0 || co->index >= MPS2_MAX_PORTS)
+ return -ENODEV;
+
+ mps_port = &mps2_uart_ports[co->index];
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(&mps_port->port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver mps2_uart_driver;
+
+static struct console mps2_uart_console = {
+ .name = SERIAL_NAME,
+ .device = uart_console_device,
+ .write = mps2_uart_console_write,
+ .setup = mps2_uart_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &mps2_uart_driver,
+};
+
+#define MPS2_SERIAL_CONSOLE (&mps2_uart_console)
+
+static void mps2_early_putchar(struct uart_port *port, int ch)
+{
+ while (readb(port->membase + UARTn_STATE) & UARTn_STATE_TX_FULL)
+ cpu_relax();
+
+ writeb((unsigned char)ch, port->membase + UARTn_DATA);
+}
+
+static void mps2_early_write(struct console *con, const char *s, unsigned int n)
+{
+ struct earlycon_device *dev = con->data;
+
+ uart_console_write(&dev->port, s, n, mps2_early_putchar);
+}
+
+static int __init mps2_early_console_setup(struct earlycon_device *device,
+ const char *opt)
+{
+ if (!device->port.membase)
+ return -ENODEV;
+
+ device->con->write = mps2_early_write;
+
+ return 0;
+}
+
+OF_EARLYCON_DECLARE(mps2, "arm,mps2-uart", mps2_early_console_setup);
+
+#else
+#define MPS2_SERIAL_CONSOLE NULL
+#endif
+
+static struct uart_driver mps2_uart_driver = {
+ .driver_name = DRIVER_NAME,
+ .dev_name = SERIAL_NAME,
+ .nr = MPS2_MAX_PORTS,
+ .cons = MPS2_SERIAL_CONSOLE,
+};
+
+static struct mps2_uart_port *mps2_of_get_port(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ int id;
+
+ if (!np)
+ return NULL;
+
+ id = of_alias_get_id(np, "serial");
+ if (id < 0)
+ id = 0;
+
+ if (WARN_ON(id >= MPS2_MAX_PORTS))
+ return NULL;
+
+ mps2_uart_ports[id].port.line = id;
+ return &mps2_uart_ports[id];
+}
+
+static int mps2_init_port(struct mps2_uart_port *mps_port,
+ struct platform_device *pdev)
+{
+ struct resource *res;
+ int ret;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mps_port->port.membase = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(mps_port->port.membase))
+ return PTR_ERR(mps_port->port.membase);
+
+ mps_port->port.mapbase = res->start;
+ mps_port->port.mapsize = resource_size(res);
+
+ mps_port->rx_irq = platform_get_irq(pdev, 0);
+ mps_port->tx_irq = platform_get_irq(pdev, 1);
+ mps_port->port.irq = platform_get_irq(pdev, 2);
+
+ mps_port->port.iotype = UPIO_MEM;
+ mps_port->port.flags = UPF_BOOT_AUTOCONF;
+ mps_port->port.fifosize = 1;
+ mps_port->port.ops = &mps2_uart_pops;
+ mps_port->port.dev = &pdev->dev;
+
+ mps_port->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(mps_port->clk))
+ return PTR_ERR(mps_port->clk);
+
+ ret = clk_prepare_enable(mps_port->clk);
+ if (ret)
+ return ret;
+
+ mps_port->port.uartclk = clk_get_rate(mps_port->clk);
+
+ clk_disable_unprepare(mps_port->clk);
+
+ return ret;
+}
+
+static int mps2_serial_probe(struct platform_device *pdev)
+{
+ struct mps2_uart_port *mps_port;
+ int ret;
+
+ mps_port = mps2_of_get_port(pdev);
+ if (!mps_port)
+ return -ENODEV;
+
+ ret = mps2_init_port(mps_port, pdev);
+ if (ret)
+ return ret;
+
+ ret = uart_add_one_port(&mps2_uart_driver, &mps_port->port);
+ if (ret)
+ return ret;
+
+ platform_set_drvdata(pdev, mps_port);
+
+ return 0;
+}
+
+static int mps2_serial_remove(struct platform_device *pdev)
+{
+ struct mps2_uart_port *mps_port = platform_get_drvdata(pdev);
+
+ uart_remove_one_port(&mps2_uart_driver, &mps_port->port);
+
+ return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id mps2_match[] = {
+ { .compatible = "arm,mps2-uart", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, mps2_match);
+#endif
+
+static struct platform_driver mps2_serial_driver = {
+ .probe = mps2_serial_probe,
+ .remove = mps2_serial_remove,
+
+ .driver = {
+ .name = DRIVER_NAME,
+ .of_match_table = of_match_ptr(mps2_match),
+ },
+};
+
+static int __init mps2_uart_init(void)
+{
+ int ret;
+
+ ret = uart_register_driver(&mps2_uart_driver);
+ if (ret)
+ return ret;
+
+ ret = platform_driver_register(&mps2_serial_driver);
+ if (ret)
+ uart_unregister_driver(&mps2_uart_driver);
+
+ return ret;
+}
+module_init(mps2_uart_init);
+
+static void __exit mps2_uart_exit(void)
+{
+ platform_driver_unregister(&mps2_serial_driver);
+ uart_unregister_driver(&mps2_uart_driver);
+}
+module_exit(mps2_uart_exit);
+
+MODULE_AUTHOR("Vladimir Murzin <vladimir.murzin@arm.com>");
+MODULE_DESCRIPTION("MPS2 UART driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:" DRIVER_NAME);
diff --git a/drivers/tty/serial/msm_serial.c b/drivers/tty/serial/msm_serial.c
index 96d3ce8..b7d80bd 100644
--- a/drivers/tty/serial/msm_serial.c
+++ b/drivers/tty/serial/msm_serial.c
@@ -861,37 +861,72 @@
};
static const struct msm_baud_map *
-msm_find_best_baud(struct uart_port *port, unsigned int baud)
+msm_find_best_baud(struct uart_port *port, unsigned int baud,
+ unsigned long *rate)
{
- unsigned int i, divisor;
- const struct msm_baud_map *entry;
+ struct msm_port *msm_port = UART_TO_MSM(port);
+ unsigned int divisor, result;
+ unsigned long target, old, best_rate = 0, diff, best_diff = ULONG_MAX;
+ const struct msm_baud_map *entry, *end, *best;
static const struct msm_baud_map table[] = {
- { 1536, 0x00, 1 },
- { 768, 0x11, 1 },
- { 384, 0x22, 1 },
- { 192, 0x33, 1 },
- { 96, 0x44, 1 },
- { 48, 0x55, 1 },
- { 32, 0x66, 1 },
- { 24, 0x77, 1 },
- { 16, 0x88, 1 },
- { 12, 0x99, 6 },
- { 8, 0xaa, 6 },
- { 6, 0xbb, 6 },
- { 4, 0xcc, 6 },
- { 3, 0xdd, 8 },
- { 2, 0xee, 16 },
{ 1, 0xff, 31 },
- { 0, 0xff, 31 },
+ { 2, 0xee, 16 },
+ { 3, 0xdd, 8 },
+ { 4, 0xcc, 6 },
+ { 6, 0xbb, 6 },
+ { 8, 0xaa, 6 },
+ { 12, 0x99, 6 },
+ { 16, 0x88, 1 },
+ { 24, 0x77, 1 },
+ { 32, 0x66, 1 },
+ { 48, 0x55, 1 },
+ { 96, 0x44, 1 },
+ { 192, 0x33, 1 },
+ { 384, 0x22, 1 },
+ { 768, 0x11, 1 },
+ { 1536, 0x00, 1 },
};
- divisor = uart_get_divisor(port, baud);
+ best = table; /* Default to smallest divider */
+ target = clk_round_rate(msm_port->clk, 16 * baud);
+ divisor = DIV_ROUND_CLOSEST(target, 16 * baud);
- for (i = 0, entry = table; i < ARRAY_SIZE(table); i++, entry++)
- if (entry->divisor <= divisor)
- break;
+ end = table + ARRAY_SIZE(table);
+ entry = table;
+ while (entry < end) {
+ if (entry->divisor <= divisor) {
+ result = target / entry->divisor / 16;
+ diff = abs(result - baud);
- return entry; /* Default to smallest divider */
+ /* Keep track of best entry */
+ if (diff < best_diff) {
+ best_diff = diff;
+ best = entry;
+ best_rate = target;
+ }
+
+ if (result == baud)
+ break;
+ } else if (entry->divisor > divisor) {
+ old = target;
+ target = clk_round_rate(msm_port->clk, old + 1);
+ /*
+ * The rate didn't get any faster so we can't do
+ * better at dividing it down
+ */
+ if (target == old)
+ break;
+
+ /* Start the divisor search over at this new rate */
+ entry = table;
+ divisor = DIV_ROUND_CLOSEST(target, 16 * baud);
+ continue;
+ }
+ entry++;
+ }
+
+ *rate = best_rate;
+ return best;
}
static int msm_set_baud_rate(struct uart_port *port, unsigned int baud,
@@ -900,22 +935,20 @@
unsigned int rxstale, watermark, mask;
struct msm_port *msm_port = UART_TO_MSM(port);
const struct msm_baud_map *entry;
- unsigned long flags;
-
- entry = msm_find_best_baud(port, baud);
-
- msm_write(port, entry->code, UART_CSR);
-
- if (baud > 460800)
- port->uartclk = baud * 16;
+ unsigned long flags, rate;
flags = *saved_flags;
spin_unlock_irqrestore(&port->lock, flags);
- clk_set_rate(msm_port->clk, port->uartclk);
+ entry = msm_find_best_baud(port, baud, &rate);
+ clk_set_rate(msm_port->clk, rate);
+ baud = rate / 16 / entry->divisor;
spin_lock_irqsave(&port->lock, flags);
*saved_flags = flags;
+ port->uartclk = rate;
+
+ msm_write(port, entry->code, UART_CSR);
/* RX stale watermark */
rxstale = entry->rxstale;
@@ -1577,8 +1610,6 @@
msm_port->pclk = devm_clk_get(&pdev->dev, "iface");
if (IS_ERR(msm_port->pclk))
return PTR_ERR(msm_port->pclk);
-
- clk_set_rate(msm_port->clk, 1843200);
}
port->uartclk = clk_get_rate(msm_port->clk);
diff --git a/drivers/tty/serial/mvebu-uart.c b/drivers/tty/serial/mvebu-uart.c
index 0ff2781..ce362bd 100644
--- a/drivers/tty/serial/mvebu-uart.c
+++ b/drivers/tty/serial/mvebu-uart.c
@@ -1,5 +1,7 @@
/*
* ***************************************************************************
+* Marvell Armada-3700 Serial Driver
+* Author: Wilson Ding <dingwei@marvell.com>
* Copyright (C) 2015 Marvell International Ltd.
* ***************************************************************************
* This program is free software: you can redistribute it and/or modify it
@@ -23,7 +25,6 @@
#include <linux/init.h>
#include <linux/io.h>
#include <linux/iopoll.h>
-#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_device.h>
@@ -594,30 +595,18 @@
return 0;
}
-static int mvebu_uart_remove(struct platform_device *pdev)
-{
- struct mvebu_uart_data *data = platform_get_drvdata(pdev);
-
- uart_remove_one_port(&mvebu_uart_driver, data->port);
- data->port->private_data = NULL;
- data->port->mapbase = 0;
- return 0;
-}
-
/* Match table for of_platform binding */
static const struct of_device_id mvebu_uart_of_match[] = {
{ .compatible = "marvell,armada-3700-uart", },
{}
};
-MODULE_DEVICE_TABLE(of, mvebu_uart_of_match);
static struct platform_driver mvebu_uart_platform_driver = {
.probe = mvebu_uart_probe,
- .remove = mvebu_uart_remove,
.driver = {
- .owner = THIS_MODULE,
.name = "mvebu-uart",
.of_match_table = of_match_ptr(mvebu_uart_of_match),
+ .suppress_bind_attrs = true,
},
};
@@ -635,16 +624,4 @@
return ret;
}
-
-static void __exit mvebu_uart_exit(void)
-{
- platform_driver_unregister(&mvebu_uart_platform_driver);
- uart_unregister_driver(&mvebu_uart_driver);
-}
-
arch_initcall(mvebu_uart_init);
-module_exit(mvebu_uart_exit);
-
-MODULE_AUTHOR("Wilson Ding <dingwei@marvell.com>");
-MODULE_DESCRIPTION("Marvell Armada-3700 Serial Driver");
-MODULE_LICENSE("GPL");
diff --git a/drivers/tty/serial/mxs-auart.c b/drivers/tty/serial/mxs-auart.c
index cd0414b..eb54e5c 100644
--- a/drivers/tty/serial/mxs-auart.c
+++ b/drivers/tty/serial/mxs-auart.c
@@ -1,17 +1,18 @@
/*
- * Freescale STMP37XX/STMP378X Application UART driver
+ * Application UART driver for:
+ * Freescale STMP37XX/STMP378X
+ * Alphascale ASM9260
*
* Author: dmitry pervushin <dimka@embeddedalley.com>
*
+ * Copyright 2014 Oleksij Rempel <linux@rempel-privat.de>
+ * Provide Alphascale ASM9260 support.
* Copyright 2008-2010 Freescale Semiconductor, Inc.
* Copyright 2008 Embedded Alley Solutions, Inc All Rights Reserved.
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
*/
#if defined(CONFIG_SERIAL_MXS_AUART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
@@ -51,30 +52,16 @@
#define MXS_AUART_PORTS 5
#define MXS_AUART_FIFO_SIZE 16
+#define SET_REG 0x4
+#define CLR_REG 0x8
+#define TOG_REG 0xc
+
#define AUART_CTRL0 0x00000000
-#define AUART_CTRL0_SET 0x00000004
-#define AUART_CTRL0_CLR 0x00000008
-#define AUART_CTRL0_TOG 0x0000000c
#define AUART_CTRL1 0x00000010
-#define AUART_CTRL1_SET 0x00000014
-#define AUART_CTRL1_CLR 0x00000018
-#define AUART_CTRL1_TOG 0x0000001c
#define AUART_CTRL2 0x00000020
-#define AUART_CTRL2_SET 0x00000024
-#define AUART_CTRL2_CLR 0x00000028
-#define AUART_CTRL2_TOG 0x0000002c
#define AUART_LINECTRL 0x00000030
-#define AUART_LINECTRL_SET 0x00000034
-#define AUART_LINECTRL_CLR 0x00000038
-#define AUART_LINECTRL_TOG 0x0000003c
#define AUART_LINECTRL2 0x00000040
-#define AUART_LINECTRL2_SET 0x00000044
-#define AUART_LINECTRL2_CLR 0x00000048
-#define AUART_LINECTRL2_TOG 0x0000004c
#define AUART_INTR 0x00000050
-#define AUART_INTR_SET 0x00000054
-#define AUART_INTR_CLR 0x00000058
-#define AUART_INTR_TOG 0x0000005c
#define AUART_DATA 0x00000060
#define AUART_STAT 0x00000070
#define AUART_DEBUG 0x00000080
@@ -136,11 +123,301 @@
#define AUART_STAT_FERR (1 << 16)
#define AUART_STAT_RXCOUNT_MASK 0xffff
+/*
+ * Start of Alphascale asm9260 defines
+ * This list contains only differences of existing bits
+ * between imx2x and asm9260
+ */
+#define ASM9260_HW_CTRL0 0x0000
+/*
+ * RW. Tell the UART to execute the RX DMA Command. The
+ * UART will clear this bit at the end of receive execution.
+ */
+#define ASM9260_BM_CTRL0_RXDMA_RUN BIT(28)
+/* RW. 0 use FIFO for status register; 1 use DMA */
+#define ASM9260_BM_CTRL0_RXTO_SOURCE_STATUS BIT(25)
+/*
+ * RW. RX TIMEOUT Enable. Valid for FIFO and DMA.
+ * Warning: If this bit is set to 0, the RX timeout will not affect receive DMA
+ * operation. If this bit is set to 1, a receive timeout will cause the receive
+ * DMA logic to terminate by filling the remaining DMA bytes with garbage data.
+ */
+#define ASM9260_BM_CTRL0_RXTO_ENABLE BIT(24)
+/*
+ * RW. Receive Timeout Counter Value: number of 8-bit-time to wait before
+ * asserting timeout on the RX input. If the RXFIFO is not empty and the RX
+ * input is idle, then the watchdog counter will decrement each bit-time. Note
+ * 7-bit-time is added to the programmed value, so a value of zero will set
+ * the counter to 7-bit-time, a value of 0x1 gives 15-bit-time and so on. Also
+ * note that the counter is reloaded at the end of each frame, so if the frame
+ * is 10 bits long and the timeout counter value is zero, then timeout will
+ * occur (when FIFO is not empty) even if the RX input is not idle. The default
+ * value is 0x3 (31 bit-time).
+ */
+#define ASM9260_BM_CTRL0_RXTO_MASK (0xff << 16)
+/* TIMEOUT = (100*7+1)*(1/BAUD) */
+#define ASM9260_BM_CTRL0_DEFAULT_RXTIMEOUT (20 << 16)
+
+/* TX ctrl register */
+#define ASM9260_HW_CTRL1 0x0010
+/*
+ * RW. Tell the UART to execute the TX DMA Command. The
+ * UART will clear this bit at the end of transmit execution.
+ */
+#define ASM9260_BM_CTRL1_TXDMA_RUN BIT(28)
+
+#define ASM9260_HW_CTRL2 0x0020
+/*
+ * RW. Receive Interrupt FIFO Level Select.
+ * The trigger points for the receive interrupt are as follows:
+ * ONE_EIGHTHS = 0x0 Trigger on FIFO full to at least 2 of 16 entries.
+ * ONE_QUARTER = 0x1 Trigger on FIFO full to at least 4 of 16 entries.
+ * ONE_HALF = 0x2 Trigger on FIFO full to at least 8 of 16 entries.
+ * THREE_QUARTERS = 0x3 Trigger on FIFO full to at least 12 of 16 entries.
+ * SEVEN_EIGHTHS = 0x4 Trigger on FIFO full to at least 14 of 16 entries.
+ */
+#define ASM9260_BM_CTRL2_RXIFLSEL (7 << 20)
+#define ASM9260_BM_CTRL2_DEFAULT_RXIFLSEL (3 << 20)
+/* RW. Same as RXIFLSEL */
+#define ASM9260_BM_CTRL2_TXIFLSEL (7 << 16)
+#define ASM9260_BM_CTRL2_DEFAULT_TXIFLSEL (2 << 16)
+/* RW. Set DTR. When this bit is 1, the output is 0. */
+#define ASM9260_BM_CTRL2_DTR BIT(10)
+/* RW. Loop Back Enable */
+#define ASM9260_BM_CTRL2_LBE BIT(7)
+#define ASM9260_BM_CTRL2_PORT_ENABLE BIT(0)
+
+#define ASM9260_HW_LINECTRL 0x0030
+/*
+ * RW. Stick Parity Select. When bits 1, 2, and 7 of this register are set, the
+ * parity bit is transmitted and checked as a 0. When bits 1 and 7 are set,
+ * and bit 2 is 0, the parity bit is transmitted and checked as a 1. When this
+ * bit is cleared stick parity is disabled.
+ */
+#define ASM9260_BM_LCTRL_SPS BIT(7)
+/* RW. Word length */
+#define ASM9260_BM_LCTRL_WLEN (3 << 5)
+#define ASM9260_BM_LCTRL_CHRL_5 (0 << 5)
+#define ASM9260_BM_LCTRL_CHRL_6 (1 << 5)
+#define ASM9260_BM_LCTRL_CHRL_7 (2 << 5)
+#define ASM9260_BM_LCTRL_CHRL_8 (3 << 5)
+
+/*
+ * Interrupt register.
+ * contains the interrupt enables and the interrupt status bits
+ */
+#define ASM9260_HW_INTR 0x0040
+/* Tx FIFO EMPTY Raw Interrupt enable */
+#define ASM9260_BM_INTR_TFEIEN BIT(27)
+/* Overrun Error Interrupt Enable. */
+#define ASM9260_BM_INTR_OEIEN BIT(26)
+/* Break Error Interrupt Enable. */
+#define ASM9260_BM_INTR_BEIEN BIT(25)
+/* Parity Error Interrupt Enable. */
+#define ASM9260_BM_INTR_PEIEN BIT(24)
+/* Framing Error Interrupt Enable. */
+#define ASM9260_BM_INTR_FEIEN BIT(23)
+
+/* nUARTDSR Modem Interrupt Enable. */
+#define ASM9260_BM_INTR_DSRMIEN BIT(19)
+/* nUARTDCD Modem Interrupt Enable. */
+#define ASM9260_BM_INTR_DCDMIEN BIT(18)
+/* nUARTRI Modem Interrupt Enable. */
+#define ASM9260_BM_INTR_RIMIEN BIT(16)
+/* Auto-Boud Timeout */
+#define ASM9260_BM_INTR_ABTO BIT(13)
+#define ASM9260_BM_INTR_ABEO BIT(12)
+/* Tx FIFO EMPTY Raw Interrupt state */
+#define ASM9260_BM_INTR_TFEIS BIT(11)
+/* Overrun Error */
+#define ASM9260_BM_INTR_OEIS BIT(10)
+/* Break Error */
+#define ASM9260_BM_INTR_BEIS BIT(9)
+/* Parity Error */
+#define ASM9260_BM_INTR_PEIS BIT(8)
+/* Framing Error */
+#define ASM9260_BM_INTR_FEIS BIT(7)
+#define ASM9260_BM_INTR_DSRMIS BIT(3)
+#define ASM9260_BM_INTR_DCDMIS BIT(2)
+#define ASM9260_BM_INTR_RIMIS BIT(0)
+
+/*
+ * RW. In DMA mode, up to 4 Received/Transmit characters can be accessed at a
+ * time. In PIO mode, only one character can be accessed at a time. The status
+ * register contains the receive data flags and valid bits.
+ */
+#define ASM9260_HW_DATA 0x0050
+
+#define ASM9260_HW_STAT 0x0060
+/* RO. If 1, UARTAPP is present in this product. */
+#define ASM9260_BM_STAT_PRESENT BIT(31)
+/* RO. If 1, HISPEED is present in this product. */
+#define ASM9260_BM_STAT_HISPEED BIT(30)
+/* RO. Receive FIFO Full. */
+#define ASM9260_BM_STAT_RXFULL BIT(26)
+
+/* RO. The UART Debug Register contains the state of the DMA signals. */
+#define ASM9260_HW_DEBUG 0x0070
+/* DMA Command Run Status */
+#define ASM9260_BM_DEBUG_TXDMARUN BIT(5)
+#define ASM9260_BM_DEBUG_RXDMARUN BIT(4)
+/* DMA Command End Status */
+#define ASM9260_BM_DEBUG_TXCMDEND BIT(3)
+#define ASM9260_BM_DEBUG_RXCMDEND BIT(2)
+/* DMA Request Status */
+#define ASM9260_BM_DEBUG_TXDMARQ BIT(1)
+#define ASM9260_BM_DEBUG_RXDMARQ BIT(0)
+
+#define ASM9260_HW_ILPR 0x0080
+
+#define ASM9260_HW_RS485CTRL 0x0090
+/*
+ * RW. This bit reverses the polarity of the direction control signal on the RTS
+ * (or DTR) pin.
+ * If 0, The direction control pin will be driven to logic ‘0’ when the
+ * transmitter has data to be sent. It will be driven to logic ‘1’ after the
+ * last bit of data has been transmitted.
+ */
+#define ASM9260_BM_RS485CTRL_ONIV BIT(5)
+/* RW. Enable Auto Direction Control. */
+#define ASM9260_BM_RS485CTRL_DIR_CTRL BIT(4)
+/*
+ * RW. If 0 and DIR_CTRL = 1, pin RTS is used for direction control.
+ * If 1 and DIR_CTRL = 1, pin DTR is used for direction control.
+ */
+#define ASM9260_BM_RS485CTRL_PINSEL BIT(3)
+/* RW. Enable Auto Address Detect (AAD). */
+#define ASM9260_BM_RS485CTRL_AADEN BIT(2)
+/* RW. Disable receiver. */
+#define ASM9260_BM_RS485CTRL_RXDIS BIT(1)
+/* RW. Enable RS-485/EIA-485 Normal Multidrop Mode (NMM) */
+#define ASM9260_BM_RS485CTRL_RS485EN BIT(0)
+
+#define ASM9260_HW_RS485ADRMATCH 0x00a0
+/* Contains the address match value. */
+#define ASM9260_BM_RS485ADRMATCH_MASK (0xff << 0)
+
+#define ASM9260_HW_RS485DLY 0x00b0
+/*
+ * RW. Contains the direction control (RTS or DTR) delay value. This delay time
+ * is in periods of the baud clock.
+ */
+#define ASM9260_BM_RS485DLY_MASK (0xff << 0)
+
+#define ASM9260_HW_AUTOBAUD 0x00c0
+/* WO. Auto-baud time-out interrupt clear bit. */
+#define ASM9260_BM_AUTOBAUD_TO_INT_CLR BIT(9)
+/* WO. End of auto-baud interrupt clear bit. */
+#define ASM9260_BM_AUTOBAUD_EO_INT_CLR BIT(8)
+/* Restart in case of timeout (counter restarts at next UART Rx falling edge) */
+#define ASM9260_BM_AUTOBAUD_AUTORESTART BIT(2)
+/* Auto-baud mode select bit. 0 - Mode 0, 1 - Mode 1. */
+#define ASM9260_BM_AUTOBAUD_MODE BIT(1)
+/*
+ * Auto-baud start (auto-baud is running). Auto-baud run bit. This bit is
+ * automatically cleared after auto-baud completion.
+ */
+#define ASM9260_BM_AUTOBAUD_START BIT(0)
+
+#define ASM9260_HW_CTRL3 0x00d0
+#define ASM9260_BM_CTRL3_OUTCLK_DIV_MASK (0xffff << 16)
+/*
+ * RW. Provide clk over OUTCLK pin. In case of asm9260 it can be configured on
+ * pins 137 and 144.
+ */
+#define ASM9260_BM_CTRL3_MASTERMODE BIT(6)
+/* RW. Baud Rate Mode: 1 - Enable sync mode. 0 - async mode. */
+#define ASM9260_BM_CTRL3_SYNCMODE BIT(4)
+/* RW. 1 - MSB bit send frist; 0 - LSB bit frist. */
+#define ASM9260_BM_CTRL3_MSBF BIT(2)
+/* RW. 1 - sample rate = 8 x Baudrate; 0 - sample rate = 16 x Baudrate. */
+#define ASM9260_BM_CTRL3_BAUD8 BIT(1)
+/* RW. 1 - Set word length to 9bit. 0 - use ASM9260_BM_LCTRL_WLEN */
+#define ASM9260_BM_CTRL3_9BIT BIT(0)
+
+#define ASM9260_HW_ISO7816_CTRL 0x00e0
+/* RW. Enable High Speed mode. */
+#define ASM9260_BM_ISO7816CTRL_HS BIT(12)
+/* Disable Successive Receive NACK */
+#define ASM9260_BM_ISO7816CTRL_DS_NACK BIT(8)
+#define ASM9260_BM_ISO7816CTRL_MAX_ITER_MASK (0xff << 4)
+/* Receive NACK Inhibit */
+#define ASM9260_BM_ISO7816CTRL_INACK BIT(3)
+#define ASM9260_BM_ISO7816CTRL_NEG_DATA BIT(2)
+/* RW. 1 - ISO7816 mode; 0 - USART mode */
+#define ASM9260_BM_ISO7816CTRL_ENABLE BIT(0)
+
+#define ASM9260_HW_ISO7816_ERRCNT 0x00f0
+/* Parity error counter. Will be cleared after reading */
+#define ASM9260_BM_ISO7816_NB_ERRORS_MASK (0xff << 0)
+
+#define ASM9260_HW_ISO7816_STATUS 0x0100
+/* Max number of Repetitions Reached */
+#define ASM9260_BM_ISO7816_STAT_ITERATION BIT(0)
+
+/* End of Alphascale asm9260 defines */
+
static struct uart_driver auart_driver;
enum mxs_auart_type {
IMX23_AUART,
IMX28_AUART,
+ ASM9260_AUART,
+};
+
+struct vendor_data {
+ const u16 *reg_offset;
+};
+
+enum {
+ REG_CTRL0,
+ REG_CTRL1,
+ REG_CTRL2,
+ REG_LINECTRL,
+ REG_LINECTRL2,
+ REG_INTR,
+ REG_DATA,
+ REG_STAT,
+ REG_DEBUG,
+ REG_VERSION,
+ REG_AUTOBAUD,
+
+ /* The size of the array - must be last */
+ REG_ARRAY_SIZE,
+};
+
+static const u16 mxs_asm9260_offsets[REG_ARRAY_SIZE] = {
+ [REG_CTRL0] = ASM9260_HW_CTRL0,
+ [REG_CTRL1] = ASM9260_HW_CTRL1,
+ [REG_CTRL2] = ASM9260_HW_CTRL2,
+ [REG_LINECTRL] = ASM9260_HW_LINECTRL,
+ [REG_INTR] = ASM9260_HW_INTR,
+ [REG_DATA] = ASM9260_HW_DATA,
+ [REG_STAT] = ASM9260_HW_STAT,
+ [REG_DEBUG] = ASM9260_HW_DEBUG,
+ [REG_AUTOBAUD] = ASM9260_HW_AUTOBAUD,
+};
+
+static const u16 mxs_stmp37xx_offsets[REG_ARRAY_SIZE] = {
+ [REG_CTRL0] = AUART_CTRL0,
+ [REG_CTRL1] = AUART_CTRL1,
+ [REG_CTRL2] = AUART_CTRL2,
+ [REG_LINECTRL] = AUART_LINECTRL,
+ [REG_LINECTRL2] = AUART_LINECTRL2,
+ [REG_INTR] = AUART_INTR,
+ [REG_DATA] = AUART_DATA,
+ [REG_STAT] = AUART_STAT,
+ [REG_DEBUG] = AUART_DEBUG,
+ [REG_VERSION] = AUART_VERSION,
+ [REG_AUTOBAUD] = AUART_AUTOBAUD,
+};
+
+static const struct vendor_data vendor_alphascale_asm9260 = {
+ .reg_offset = mxs_asm9260_offsets,
+};
+
+static const struct vendor_data vendor_freescale_stmp37xx = {
+ .reg_offset = mxs_stmp37xx_offsets,
};
struct mxs_auart_port {
@@ -153,8 +430,10 @@
unsigned long flags;
unsigned int mctrl_prev;
enum mxs_auart_type devtype;
+ const struct vendor_data *vendor;
struct clk *clk;
+ struct clk *clk_ahb;
struct device *dev;
/* for DMA */
@@ -174,6 +453,7 @@
static const struct platform_device_id mxs_auart_devtype[] = {
{ .name = "mxs-auart-imx23", .driver_data = IMX23_AUART },
{ .name = "mxs-auart-imx28", .driver_data = IMX28_AUART },
+ { .name = "as-auart-asm9260", .driver_data = ASM9260_AUART },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(platform, mxs_auart_devtype);
@@ -185,6 +465,9 @@
}, {
.compatible = "fsl,imx23-auart",
.data = &mxs_auart_devtype[IMX23_AUART]
+ }, {
+ .compatible = "alphascale,asm9260-auart",
+ .data = &mxs_auart_devtype[ASM9260_AUART]
}, { /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, mxs_auart_dt_ids);
@@ -194,11 +477,54 @@
return s->devtype == IMX28_AUART;
}
+static inline int is_asm9260_auart(struct mxs_auart_port *s)
+{
+ return s->devtype == ASM9260_AUART;
+}
+
static inline bool auart_dma_enabled(struct mxs_auart_port *s)
{
return s->flags & MXS_AUART_DMA_ENABLED;
}
+static unsigned int mxs_reg_to_offset(const struct mxs_auart_port *uap,
+ unsigned int reg)
+{
+ return uap->vendor->reg_offset[reg];
+}
+
+static unsigned int mxs_read(const struct mxs_auart_port *uap,
+ unsigned int reg)
+{
+ void __iomem *addr = uap->port.membase + mxs_reg_to_offset(uap, reg);
+
+ return readl_relaxed(addr);
+}
+
+static void mxs_write(unsigned int val, struct mxs_auart_port *uap,
+ unsigned int reg)
+{
+ void __iomem *addr = uap->port.membase + mxs_reg_to_offset(uap, reg);
+
+ writel_relaxed(val, addr);
+}
+
+static void mxs_set(unsigned int val, struct mxs_auart_port *uap,
+ unsigned int reg)
+{
+ void __iomem *addr = uap->port.membase + mxs_reg_to_offset(uap, reg);
+
+ writel_relaxed(val, addr + SET_REG);
+}
+
+static void mxs_clr(unsigned int val, struct mxs_auart_port *uap,
+ unsigned int reg)
+{
+ void __iomem *addr = uap->port.membase + mxs_reg_to_offset(uap, reg);
+
+ writel_relaxed(val, addr + CLR_REG);
+}
+
static void mxs_auart_stop_tx(struct uart_port *u);
#define to_auart_port(u) container_of(u, struct mxs_auart_port, port)
@@ -295,19 +621,16 @@
}
- while (!(readl(s->port.membase + AUART_STAT) &
- AUART_STAT_TXFF)) {
+ while (!(mxs_read(s, REG_STAT) & AUART_STAT_TXFF)) {
if (s->port.x_char) {
s->port.icount.tx++;
- writel(s->port.x_char,
- s->port.membase + AUART_DATA);
+ mxs_write(s->port.x_char, s, REG_DATA);
s->port.x_char = 0;
continue;
}
if (!uart_circ_empty(xmit) && !uart_tx_stopped(&s->port)) {
s->port.icount.tx++;
- writel(xmit->buf[xmit->tail],
- s->port.membase + AUART_DATA);
+ mxs_write(xmit->buf[xmit->tail], s, REG_DATA);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
} else
break;
@@ -316,11 +639,9 @@
uart_write_wakeup(&s->port);
if (uart_circ_empty(&(s->port.state->xmit)))
- writel(AUART_INTR_TXIEN,
- s->port.membase + AUART_INTR_CLR);
+ mxs_clr(AUART_INTR_TXIEN, s, REG_INTR);
else
- writel(AUART_INTR_TXIEN,
- s->port.membase + AUART_INTR_SET);
+ mxs_set(AUART_INTR_TXIEN, s, REG_INTR);
if (uart_tx_stopped(&s->port))
mxs_auart_stop_tx(&s->port);
@@ -332,8 +653,8 @@
u32 stat;
u8 c;
- c = readl(s->port.membase + AUART_DATA);
- stat = readl(s->port.membase + AUART_STAT);
+ c = mxs_read(s, REG_DATA);
+ stat = mxs_read(s, REG_STAT);
flag = TTY_NORMAL;
s->port.icount.rx++;
@@ -368,7 +689,7 @@
uart_insert_char(&s->port, stat, AUART_STAT_OERR, c, flag);
out:
- writel(stat, s->port.membase + AUART_STAT);
+ mxs_write(stat, s, REG_STAT);
}
static void mxs_auart_rx_chars(struct mxs_auart_port *s)
@@ -376,13 +697,13 @@
u32 stat = 0;
for (;;) {
- stat = readl(s->port.membase + AUART_STAT);
+ stat = mxs_read(s, REG_STAT);
if (stat & AUART_STAT_RXFE)
break;
mxs_auart_rx_char(s);
}
- writel(stat, s->port.membase + AUART_STAT);
+ mxs_write(stat, s, REG_STAT);
tty_flip_buffer_push(&s->port.state->port);
}
@@ -418,7 +739,7 @@
{
struct mxs_auart_port *s = to_auart_port(u);
- u32 ctrl = readl(u->membase + AUART_CTRL2);
+ u32 ctrl = mxs_read(s, REG_CTRL2);
ctrl &= ~(AUART_CTRL2_RTSEN | AUART_CTRL2_RTS);
if (mctrl & TIOCM_RTS) {
@@ -428,7 +749,7 @@
ctrl |= AUART_CTRL2_RTS;
}
- writel(ctrl, u->membase + AUART_CTRL2);
+ mxs_write(ctrl, s, REG_CTRL2);
mctrl_gpio_set(s->gpios, mctrl);
}
@@ -459,7 +780,7 @@
static u32 mxs_auart_get_mctrl(struct uart_port *u)
{
struct mxs_auart_port *s = to_auart_port(u);
- u32 stat = readl(u->membase + AUART_STAT);
+ u32 stat = mxs_read(s, REG_STAT);
u32 mctrl = 0;
if (stat & AUART_STAT_CTS)
@@ -536,14 +857,14 @@
dma_unmap_sg(s->dev, &s->rx_sgl, 1, DMA_FROM_DEVICE);
- stat = readl(s->port.membase + AUART_STAT);
+ stat = mxs_read(s, REG_STAT);
stat &= ~(AUART_STAT_OERR | AUART_STAT_BERR |
AUART_STAT_PERR | AUART_STAT_FERR);
count = stat & AUART_STAT_RXCOUNT_MASK;
tty_insert_flip_string(port, s->rx_dma_buf, count);
- writel(stat, s->port.membase + AUART_STAT);
+ mxs_write(stat, s, REG_STAT);
tty_flip_buffer_push(port);
/* start the next DMA for RX. */
@@ -606,8 +927,8 @@
static void mxs_auart_dma_exit(struct mxs_auart_port *s)
{
- writel(AUART_CTRL2_TXDMAE | AUART_CTRL2_RXDMAE | AUART_CTRL2_DMAONERR,
- s->port.membase + AUART_CTRL2_CLR);
+ mxs_clr(AUART_CTRL2_TXDMAE | AUART_CTRL2_RXDMAE | AUART_CTRL2_DMAONERR,
+ s, REG_CTRL2);
mxs_auart_dma_exit_channel(s);
s->flags &= ~MXS_AUART_DMA_ENABLED;
@@ -666,7 +987,7 @@
cflag = termios->c_cflag;
ctrl = AUART_LINECTRL_FEN;
- ctrl2 = readl(u->membase + AUART_CTRL2);
+ ctrl2 = mxs_read(s, REG_CTRL2);
/* byte size */
switch (cflag & CSIZE) {
@@ -754,15 +1075,24 @@
}
/* set baud rate */
- baud_min = DIV_ROUND_UP(u->uartclk * 32, AUART_LINECTRL_BAUD_DIV_MAX);
- baud_max = u->uartclk * 32 / AUART_LINECTRL_BAUD_DIV_MIN;
- baud = uart_get_baud_rate(u, termios, old, baud_min, baud_max);
- div = u->uartclk * 32 / baud;
+ if (is_asm9260_auart(s)) {
+ baud = uart_get_baud_rate(u, termios, old,
+ u->uartclk * 4 / 0x3FFFFF,
+ u->uartclk / 16);
+ div = u->uartclk * 4 / baud;
+ } else {
+ baud_min = DIV_ROUND_UP(u->uartclk * 32,
+ AUART_LINECTRL_BAUD_DIV_MAX);
+ baud_max = u->uartclk * 32 / AUART_LINECTRL_BAUD_DIV_MIN;
+ baud = uart_get_baud_rate(u, termios, old, baud_min, baud_max);
+ div = u->uartclk * 32 / baud;
+ }
+
ctrl |= AUART_LINECTRL_BAUD_DIVFRAC(div & 0x3F);
ctrl |= AUART_LINECTRL_BAUD_DIVINT(div >> 6);
+ mxs_write(ctrl, s, REG_LINECTRL);
- writel(ctrl, u->membase + AUART_LINECTRL);
- writel(ctrl2, u->membase + AUART_CTRL2);
+ mxs_write(ctrl2, s, REG_CTRL2);
uart_update_timeout(u, termios->c_cflag, baud);
@@ -771,8 +1101,8 @@
!test_and_set_bit(MXS_AUART_DMA_RX_READY, &s->flags)) {
if (!mxs_auart_dma_prep_rx(s)) {
/* Disable the normal RX interrupt. */
- writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN,
- u->membase + AUART_INTR_CLR);
+ mxs_clr(AUART_INTR_RXIEN | AUART_INTR_RTIEN,
+ s, REG_INTR);
} else {
mxs_auart_dma_exit(s);
dev_err(s->dev, "We can not start up the DMA.\n");
@@ -802,16 +1132,13 @@
u32 istat;
struct mxs_auart_port *s = context;
u32 mctrl_temp = s->mctrl_prev;
- u32 stat = readl(s->port.membase + AUART_STAT);
+ u32 stat = mxs_read(s, REG_STAT);
- istat = readl(s->port.membase + AUART_INTR);
+ istat = mxs_read(s, REG_INTR);
/* ack irq */
- writel(istat & (AUART_INTR_RTIS
- | AUART_INTR_TXIS
- | AUART_INTR_RXIS
- | AUART_INTR_CTSMIS),
- s->port.membase + AUART_INTR_CLR);
+ mxs_clr(istat & (AUART_INTR_RTIS | AUART_INTR_TXIS | AUART_INTR_RXIS
+ | AUART_INTR_CTSMIS), s, REG_INTR);
/*
* Dealing with GPIO interrupt
@@ -827,8 +1154,7 @@
if (CTS_AT_AUART() && s->ms_irq_enabled)
uart_handle_cts_change(&s->port,
stat & AUART_STAT_CTS);
- writel(AUART_INTR_CTSMIS,
- s->port.membase + AUART_INTR_CLR);
+ mxs_clr(AUART_INTR_CTSMIS, s, REG_INTR);
istat &= ~AUART_INTR_CTSMIS;
}
@@ -846,44 +1172,44 @@
return IRQ_HANDLED;
}
-static void mxs_auart_reset_deassert(struct uart_port *u)
+static void mxs_auart_reset_deassert(struct mxs_auart_port *s)
{
int i;
unsigned int reg;
- writel(AUART_CTRL0_SFTRST, u->membase + AUART_CTRL0_CLR);
+ mxs_clr(AUART_CTRL0_SFTRST, s, REG_CTRL0);
for (i = 0; i < 10000; i++) {
- reg = readl(u->membase + AUART_CTRL0);
+ reg = mxs_read(s, REG_CTRL0);
if (!(reg & AUART_CTRL0_SFTRST))
break;
udelay(3);
}
- writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_CLR);
+ mxs_clr(AUART_CTRL0_CLKGATE, s, REG_CTRL0);
}
-static void mxs_auart_reset_assert(struct uart_port *u)
+static void mxs_auart_reset_assert(struct mxs_auart_port *s)
{
int i;
u32 reg;
- reg = readl(u->membase + AUART_CTRL0);
+ reg = mxs_read(s, REG_CTRL0);
/* if already in reset state, keep it untouched */
if (reg & AUART_CTRL0_SFTRST)
return;
- writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_CLR);
- writel(AUART_CTRL0_SFTRST, u->membase + AUART_CTRL0_SET);
+ mxs_clr(AUART_CTRL0_CLKGATE, s, REG_CTRL0);
+ mxs_set(AUART_CTRL0_SFTRST, s, REG_CTRL0);
for (i = 0; i < 1000; i++) {
- reg = readl(u->membase + AUART_CTRL0);
+ reg = mxs_read(s, REG_CTRL0);
/* reset is finished when the clock is gated */
if (reg & AUART_CTRL0_CLKGATE)
return;
udelay(10);
}
- dev_err(u->dev, "Failed to reset the unit.");
+ dev_err(s->dev, "Failed to reset the unit.");
}
static int mxs_auart_startup(struct uart_port *u)
@@ -896,17 +1222,17 @@
return ret;
if (uart_console(u)) {
- writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_CLR);
+ mxs_clr(AUART_CTRL0_CLKGATE, s, REG_CTRL0);
} else {
/* reset the unit to a well known state */
- mxs_auart_reset_assert(u);
- mxs_auart_reset_deassert(u);
+ mxs_auart_reset_assert(s);
+ mxs_auart_reset_deassert(s);
}
- writel(AUART_CTRL2_UARTEN, u->membase + AUART_CTRL2_SET);
+ mxs_set(AUART_CTRL2_UARTEN, s, REG_CTRL2);
- writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
- u->membase + AUART_INTR);
+ mxs_write(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
+ s, REG_INTR);
/* Reset FIFO size (it could have changed if DMA was enabled) */
u->fifosize = MXS_AUART_FIFO_SIZE;
@@ -915,7 +1241,7 @@
* Enable fifo so all four bytes of a DMA word are written to
* output (otherwise, only the LSB is written, ie. 1 in 4 bytes)
*/
- writel(AUART_LINECTRL_FEN, u->membase + AUART_LINECTRL_SET);
+ mxs_set(AUART_LINECTRL_FEN, s, REG_LINECTRL);
/* get initial status of modem lines */
mctrl_gpio_get(s->gpios, &s->mctrl_prev);
@@ -934,12 +1260,13 @@
mxs_auart_dma_exit(s);
if (uart_console(u)) {
- writel(AUART_CTRL2_UARTEN, u->membase + AUART_CTRL2_CLR);
- writel(AUART_INTR_RXIEN | AUART_INTR_RTIEN | AUART_INTR_CTSMIEN,
- u->membase + AUART_INTR_CLR);
- writel(AUART_CTRL0_CLKGATE, u->membase + AUART_CTRL0_SET);
+ mxs_clr(AUART_CTRL2_UARTEN, s, REG_CTRL2);
+
+ mxs_clr(AUART_INTR_RXIEN | AUART_INTR_RTIEN |
+ AUART_INTR_CTSMIEN, s, REG_INTR);
+ mxs_set(AUART_CTRL0_CLKGATE, s, REG_CTRL0);
} else {
- mxs_auart_reset_assert(u);
+ mxs_auart_reset_assert(s);
}
clk_disable_unprepare(s->clk);
@@ -947,7 +1274,9 @@
static unsigned int mxs_auart_tx_empty(struct uart_port *u)
{
- if ((readl(u->membase + AUART_STAT) &
+ struct mxs_auart_port *s = to_auart_port(u);
+
+ if ((mxs_read(s, REG_STAT) &
(AUART_STAT_TXFE | AUART_STAT_BUSY)) == AUART_STAT_TXFE)
return TIOCSER_TEMT;
@@ -959,29 +1288,33 @@
struct mxs_auart_port *s = to_auart_port(u);
/* enable transmitter */
- writel(AUART_CTRL2_TXE, u->membase + AUART_CTRL2_SET);
+ mxs_set(AUART_CTRL2_TXE, s, REG_CTRL2);
mxs_auart_tx_chars(s);
}
static void mxs_auart_stop_tx(struct uart_port *u)
{
- writel(AUART_CTRL2_TXE, u->membase + AUART_CTRL2_CLR);
+ struct mxs_auart_port *s = to_auart_port(u);
+
+ mxs_clr(AUART_CTRL2_TXE, s, REG_CTRL2);
}
static void mxs_auart_stop_rx(struct uart_port *u)
{
- writel(AUART_CTRL2_RXE, u->membase + AUART_CTRL2_CLR);
+ struct mxs_auart_port *s = to_auart_port(u);
+
+ mxs_clr(AUART_CTRL2_RXE, s, REG_CTRL2);
}
static void mxs_auart_break_ctl(struct uart_port *u, int ctl)
{
+ struct mxs_auart_port *s = to_auart_port(u);
+
if (ctl)
- writel(AUART_LINECTRL_BRK,
- u->membase + AUART_LINECTRL_SET);
+ mxs_set(AUART_LINECTRL_BRK, s, REG_LINECTRL);
else
- writel(AUART_LINECTRL_BRK,
- u->membase + AUART_LINECTRL_CLR);
+ mxs_clr(AUART_LINECTRL_BRK, s, REG_LINECTRL);
}
static struct uart_ops mxs_auart_ops = {
@@ -1009,15 +1342,16 @@
#ifdef CONFIG_SERIAL_MXS_AUART_CONSOLE
static void mxs_auart_console_putchar(struct uart_port *port, int ch)
{
+ struct mxs_auart_port *s = to_auart_port(port);
unsigned int to = 1000;
- while (readl(port->membase + AUART_STAT) & AUART_STAT_TXFF) {
+ while (mxs_read(s, REG_STAT) & AUART_STAT_TXFF) {
if (!to--)
break;
udelay(1);
}
- writel(ch, port->membase + AUART_DATA);
+ mxs_write(ch, s, REG_DATA);
}
static void
@@ -1037,18 +1371,16 @@
clk_enable(s->clk);
/* First save the CR then disable the interrupts */
- old_ctrl2 = readl(port->membase + AUART_CTRL2);
- old_ctrl0 = readl(port->membase + AUART_CTRL0);
+ old_ctrl2 = mxs_read(s, REG_CTRL2);
+ old_ctrl0 = mxs_read(s, REG_CTRL0);
- writel(AUART_CTRL0_CLKGATE,
- port->membase + AUART_CTRL0_CLR);
- writel(AUART_CTRL2_UARTEN | AUART_CTRL2_TXE,
- port->membase + AUART_CTRL2_SET);
+ mxs_clr(AUART_CTRL0_CLKGATE, s, REG_CTRL0);
+ mxs_set(AUART_CTRL2_UARTEN | AUART_CTRL2_TXE, s, REG_CTRL2);
uart_console_write(port, str, count, mxs_auart_console_putchar);
/* Finally, wait for transmitter to become empty ... */
- while (readl(port->membase + AUART_STAT) & AUART_STAT_BUSY) {
+ while (mxs_read(s, REG_STAT) & AUART_STAT_BUSY) {
udelay(1);
if (!to--)
break;
@@ -1060,24 +1392,25 @@
* unused, but that is better than to disable it while it is still
* transmitting.
*/
- if (!(readl(port->membase + AUART_STAT) & AUART_STAT_BUSY)) {
- writel(old_ctrl0, port->membase + AUART_CTRL0);
- writel(old_ctrl2, port->membase + AUART_CTRL2);
+ if (!(mxs_read(s, REG_STAT) & AUART_STAT_BUSY)) {
+ mxs_write(old_ctrl0, s, REG_CTRL0);
+ mxs_write(old_ctrl2, s, REG_CTRL2);
}
clk_disable(s->clk);
}
static void __init
-auart_console_get_options(struct uart_port *port, int *baud,
+auart_console_get_options(struct mxs_auart_port *s, int *baud,
int *parity, int *bits)
{
+ struct uart_port *port = &s->port;
unsigned int lcr_h, quot;
- if (!(readl(port->membase + AUART_CTRL2) & AUART_CTRL2_UARTEN))
+ if (!(mxs_read(s, REG_CTRL2) & AUART_CTRL2_UARTEN))
return;
- lcr_h = readl(port->membase + AUART_LINECTRL);
+ lcr_h = mxs_read(s, REG_LINECTRL);
*parity = 'n';
if (lcr_h & AUART_LINECTRL_PEN) {
@@ -1092,12 +1425,10 @@
else
*bits = 8;
- quot = ((readl(port->membase + AUART_LINECTRL)
- & AUART_LINECTRL_BAUD_DIVINT_MASK))
- >> (AUART_LINECTRL_BAUD_DIVINT_SHIFT - 6);
- quot |= ((readl(port->membase + AUART_LINECTRL)
- & AUART_LINECTRL_BAUD_DIVFRAC_MASK))
- >> AUART_LINECTRL_BAUD_DIVFRAC_SHIFT;
+ quot = ((mxs_read(s, REG_LINECTRL) & AUART_LINECTRL_BAUD_DIVINT_MASK))
+ >> (AUART_LINECTRL_BAUD_DIVINT_SHIFT - 6);
+ quot |= ((mxs_read(s, REG_LINECTRL) & AUART_LINECTRL_BAUD_DIVFRAC_MASK))
+ >> AUART_LINECTRL_BAUD_DIVFRAC_SHIFT;
if (quot == 0)
quot = 1;
@@ -1132,7 +1463,7 @@
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else
- auart_console_get_options(&s->port, &baud, &parity, &bits);
+ auart_console_get_options(s, &baud, &parity, &bits);
ret = uart_set_options(&s->port, co, baud, parity, bits, flow);
@@ -1164,6 +1495,60 @@
#endif
};
+static void mxs_init_regs(struct mxs_auart_port *s)
+{
+ if (is_asm9260_auart(s))
+ s->vendor = &vendor_alphascale_asm9260;
+ else
+ s->vendor = &vendor_freescale_stmp37xx;
+}
+
+static int mxs_get_clks(struct mxs_auart_port *s,
+ struct platform_device *pdev)
+{
+ int err;
+
+ if (!is_asm9260_auart(s)) {
+ s->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(s->clk))
+ return PTR_ERR(s->clk);
+
+ return 0;
+ }
+
+ s->clk = devm_clk_get(s->dev, "mod");
+ if (IS_ERR(s->clk)) {
+ dev_err(s->dev, "Failed to get \"mod\" clk\n");
+ return PTR_ERR(s->clk);
+ }
+
+ s->clk_ahb = devm_clk_get(s->dev, "ahb");
+ if (IS_ERR(s->clk_ahb)) {
+ dev_err(s->dev, "Failed to get \"ahb\" clk\n");
+ return PTR_ERR(s->clk_ahb);
+ }
+
+ err = clk_prepare_enable(s->clk_ahb);
+ if (err) {
+ dev_err(s->dev, "Failed to enable ahb_clk!\n");
+ return err;
+ }
+
+ err = clk_set_rate(s->clk, clk_get_rate(s->clk_ahb));
+ if (err) {
+ dev_err(s->dev, "Failed to set rate!\n");
+ return err;
+ }
+
+ err = clk_prepare_enable(s->clk);
+ if (err) {
+ dev_err(s->dev, "Failed to enable clk!\n");
+ return err;
+ }
+
+ return 0;
+}
+
/*
* This function returns 1 if pdev isn't a device instatiated by dt, 0 if it
* could successfully get all information from dt or a negative errno.
@@ -1185,7 +1570,8 @@
}
s->port.line = ret;
- if (of_get_property(np, "fsl,uart-has-rtscts", NULL))
+ if (of_get_property(np, "uart-has-rtscts", NULL) ||
+ of_get_property(np, "fsl,uart-has-rtscts", NULL) /* deprecated */)
set_bit(MXS_AUART_RTSCTS, &s->flags);
return 0;
@@ -1269,6 +1655,9 @@
if (!s)
return -ENOMEM;
+ s->port.dev = &pdev->dev;
+ s->dev = &pdev->dev;
+
ret = serial_mxs_probe_dt(s, pdev);
if (ret > 0)
s->port.line = pdev->id < 0 ? 0 : pdev->id;
@@ -1280,15 +1669,14 @@
s->devtype = pdev->id_entry->driver_data;
}
- s->clk = devm_clk_get(&pdev->dev, NULL);
- if (IS_ERR(s->clk))
- return PTR_ERR(s->clk);
+ ret = mxs_get_clks(s, pdev);
+ if (ret)
+ return ret;
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!r)
return -ENXIO;
-
s->port.mapbase = r->start;
s->port.membase = ioremap(r->start, resource_size(r));
s->port.ops = &mxs_auart_ops;
@@ -1296,7 +1684,8 @@
s->port.fifosize = MXS_AUART_FIFO_SIZE;
s->port.uartclk = clk_get_rate(s->clk);
s->port.type = PORT_IMX;
- s->port.dev = s->dev = &pdev->dev;
+
+ mxs_init_regs(s);
s->mctrl_prev = 0;
@@ -1327,16 +1716,21 @@
auart_port[s->port.line] = s;
- mxs_auart_reset_deassert(&s->port);
+ mxs_auart_reset_deassert(s);
ret = uart_add_one_port(&auart_driver, &s->port);
if (ret)
goto out_free_gpio_irq;
- version = readl(s->port.membase + AUART_VERSION);
- dev_info(&pdev->dev, "Found APPUART %d.%d.%d\n",
- (version >> 24) & 0xff,
- (version >> 16) & 0xff, version & 0xffff);
+ /* ASM9260 don't have version reg */
+ if (is_asm9260_auart(s)) {
+ dev_info(&pdev->dev, "Found APPUART ASM9260\n");
+ } else {
+ version = mxs_read(s, REG_VERSION);
+ dev_info(&pdev->dev, "Found APPUART %d.%d.%d\n",
+ (version >> 24) & 0xff,
+ (version >> 16) & 0xff, version & 0xffff);
+ }
return 0;
diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c
index ac7f8df..99bb231 100644
--- a/drivers/tty/serial/samsung.c
+++ b/drivers/tty/serial/samsung.c
@@ -1271,6 +1271,8 @@
/* check to see if we need to change clock source */
if (ourport->baudclk != clk) {
+ clk_prepare_enable(clk);
+
s3c24xx_serial_setsource(port, clk_sel);
if (!IS_ERR(ourport->baudclk)) {
@@ -1278,8 +1280,6 @@
ourport->baudclk = ERR_PTR(-EINVAL);
}
- clk_prepare_enable(clk);
-
ourport->baudclk = clk;
ourport->baudclk_rate = clk ? clk_get_rate(clk) : 0;
}
diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index e639361..f36e6df 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -666,7 +666,7 @@
struct uart_port *port = &s->p[portno].port;
do {
- unsigned int iir, msr, rxlen;
+ unsigned int iir, rxlen;
iir = sc16is7xx_port_read(port, SC16IS7XX_IIR_REG);
if (iir & SC16IS7XX_IIR_NO_INT_BIT)
@@ -683,12 +683,6 @@
if (rxlen)
sc16is7xx_handle_rx(port, rxlen, iir);
break;
-
- case SC16IS7XX_IIR_CTSRTS_SRC:
- msr = sc16is7xx_port_read(port, SC16IS7XX_MSR_REG);
- uart_handle_cts_change(port,
- !!(msr & SC16IS7XX_MSR_DCTS_BIT));
- break;
case SC16IS7XX_IIR_THRI_SRC:
sc16is7xx_handle_tx(port);
break;
@@ -1014,9 +1008,8 @@
SC16IS7XX_EFCR_TXDISABLE_BIT,
0);
- /* Enable RX, TX, CTS change interrupts */
- val = SC16IS7XX_IER_RDI_BIT | SC16IS7XX_IER_THRI_BIT |
- SC16IS7XX_IER_CTSI_BIT;
+ /* Enable RX, TX interrupts */
+ val = SC16IS7XX_IER_RDI_BIT | SC16IS7XX_IER_THRI_BIT;
sc16is7xx_port_write(port, SC16IS7XX_IER_REG, val);
return 0;
diff --git a/drivers/tty/serial/serial-tegra.c b/drivers/tty/serial/serial-tegra.c
index 1d6fc60..1dba671 100644
--- a/drivers/tty/serial/serial-tegra.c
+++ b/drivers/tty/serial/serial-tegra.c
@@ -206,10 +206,8 @@
static void tegra_uart_set_mctrl(struct uart_port *u, unsigned int mctrl)
{
struct tegra_uart_port *tup = to_tegra_uport(u);
- unsigned long mcr;
int dtr_enable;
- mcr = tup->mcr_shadow;
tup->rts_active = !!(mctrl & TIOCM_RTS);
set_rts(tup, tup->rts_active);
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index a126a60..a333c59 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -64,6 +64,41 @@
return !!(uport->status & UPSTAT_DCD_ENABLE);
}
+static inline struct uart_port *uart_port_ref(struct uart_state *state)
+{
+ if (atomic_add_unless(&state->refcount, 1, 0))
+ return state->uart_port;
+ return NULL;
+}
+
+static inline void uart_port_deref(struct uart_port *uport)
+{
+ if (uport && atomic_dec_and_test(&uport->state->refcount))
+ wake_up(&uport->state->remove_wait);
+}
+
+#define uart_port_lock(state, flags) \
+ ({ \
+ struct uart_port *__uport = uart_port_ref(state); \
+ if (__uport) \
+ spin_lock_irqsave(&__uport->lock, flags); \
+ __uport; \
+ })
+
+#define uart_port_unlock(uport, flags) \
+ ({ \
+ struct uart_port *__uport = uport; \
+ if (__uport) \
+ spin_unlock_irqrestore(&__uport->lock, flags); \
+ uart_port_deref(__uport); \
+ })
+
+static inline struct uart_port *uart_port_check(struct uart_state *state)
+{
+ lockdep_assert_held(&state->port.mutex);
+ return state->uart_port;
+}
+
/*
* This routine is used by the interrupt handler to schedule processing in
* the software interrupt portion of the driver.
@@ -82,12 +117,13 @@
static void uart_stop(struct tty_struct *tty)
{
struct uart_state *state = tty->driver_data;
- struct uart_port *port = state->uart_port;
+ struct uart_port *port;
unsigned long flags;
- spin_lock_irqsave(&port->lock, flags);
- port->ops->stop_tx(port);
- spin_unlock_irqrestore(&port->lock, flags);
+ port = uart_port_lock(state, flags);
+ if (port)
+ port->ops->stop_tx(port);
+ uart_port_unlock(port, flags);
}
static void __uart_start(struct tty_struct *tty)
@@ -95,19 +131,19 @@
struct uart_state *state = tty->driver_data;
struct uart_port *port = state->uart_port;
- if (!uart_tx_stopped(port))
+ if (port && !uart_tx_stopped(port))
port->ops->start_tx(port);
}
static void uart_start(struct tty_struct *tty)
{
struct uart_state *state = tty->driver_data;
- struct uart_port *port = state->uart_port;
+ struct uart_port *port;
unsigned long flags;
- spin_lock_irqsave(&port->lock, flags);
+ port = uart_port_lock(state, flags);
__uart_start(tty);
- spin_unlock_irqrestore(&port->lock, flags);
+ uart_port_unlock(port, flags);
}
static void
@@ -134,7 +170,7 @@
static int uart_port_startup(struct tty_struct *tty, struct uart_state *state,
int init_hw)
{
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport = uart_port_check(state);
unsigned long page;
int retval = 0;
@@ -196,7 +232,7 @@
struct tty_port *port = &state->port;
int retval;
- if (port->flags & ASYNC_INITIALIZED)
+ if (tty_port_initialized(port))
return 0;
/*
@@ -207,7 +243,7 @@
retval = uart_port_startup(tty, state, init_hw);
if (!retval) {
- set_bit(ASYNCB_INITIALIZED, &port->flags);
+ tty_port_set_initialized(port, 1);
clear_bit(TTY_IO_ERROR, &tty->flags);
} else if (retval > 0)
retval = 0;
@@ -219,10 +255,12 @@
* This routine will shutdown a serial port; interrupts are disabled, and
* DTR is dropped if the hangup on close termio flag is on. Calls to
* uart_shutdown are serialised by the per-port semaphore.
+ *
+ * uport == NULL if uart_port has already been removed
*/
static void uart_shutdown(struct tty_struct *tty, struct uart_state *state)
{
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport = uart_port_check(state);
struct tty_port *port = &state->port;
/*
@@ -231,11 +269,13 @@
if (tty)
set_bit(TTY_IO_ERROR, &tty->flags);
- if (test_and_clear_bit(ASYNCB_INITIALIZED, &port->flags)) {
+ if (tty_port_initialized(port)) {
+ tty_port_set_initialized(port, 0);
+
/*
* Turn off DTR and RTS early.
*/
- if (uart_console(uport) && tty)
+ if (uport && uart_console(uport) && tty)
uport->cons->cflag = tty->termios.c_cflag;
if (!tty || C_HUPCL(tty))
@@ -249,7 +289,7 @@
* a DCD drop (hangup) at just the right time. Clear suspended bit so
* we don't try to resume a port that has been shutdown.
*/
- clear_bit(ASYNCB_SUSPENDED, &port->flags);
+ tty_port_set_suspended(port, 0);
/*
* Free the transmit buffer page.
@@ -441,7 +481,7 @@
static void uart_change_speed(struct tty_struct *tty, struct uart_state *state,
struct ktermios *old_termios)
{
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport = uart_port_check(state);
struct ktermios *termios;
int hw_stopped;
@@ -486,7 +526,7 @@
static int uart_put_char(struct tty_struct *tty, unsigned char c)
{
struct uart_state *state = tty->driver_data;
- struct uart_port *port = state->uart_port;
+ struct uart_port *port;
struct circ_buf *circ;
unsigned long flags;
int ret = 0;
@@ -495,13 +535,13 @@
if (!circ->buf)
return 0;
- spin_lock_irqsave(&port->lock, flags);
- if (uart_circ_chars_free(circ) != 0) {
+ port = uart_port_lock(state, flags);
+ if (port && uart_circ_chars_free(circ) != 0) {
circ->buf[circ->head] = c;
circ->head = (circ->head + 1) & (UART_XMIT_SIZE - 1);
ret = 1;
}
- spin_unlock_irqrestore(&port->lock, flags);
+ uart_port_unlock(port, flags);
return ret;
}
@@ -528,14 +568,12 @@
return -EL3HLT;
}
- port = state->uart_port;
circ = &state->xmit;
-
if (!circ->buf)
return 0;
- spin_lock_irqsave(&port->lock, flags);
- while (1) {
+ port = uart_port_lock(state, flags);
+ while (port) {
c = CIRC_SPACE_TO_END(circ->head, circ->tail, UART_XMIT_SIZE);
if (count < c)
c = count;
@@ -549,32 +587,33 @@
}
__uart_start(tty);
- spin_unlock_irqrestore(&port->lock, flags);
-
+ uart_port_unlock(port, flags);
return ret;
}
static int uart_write_room(struct tty_struct *tty)
{
struct uart_state *state = tty->driver_data;
+ struct uart_port *port;
unsigned long flags;
int ret;
- spin_lock_irqsave(&state->uart_port->lock, flags);
+ port = uart_port_lock(state, flags);
ret = uart_circ_chars_free(&state->xmit);
- spin_unlock_irqrestore(&state->uart_port->lock, flags);
+ uart_port_unlock(port, flags);
return ret;
}
static int uart_chars_in_buffer(struct tty_struct *tty)
{
struct uart_state *state = tty->driver_data;
+ struct uart_port *port;
unsigned long flags;
int ret;
- spin_lock_irqsave(&state->uart_port->lock, flags);
+ port = uart_port_lock(state, flags);
ret = uart_circ_chars_pending(&state->xmit);
- spin_unlock_irqrestore(&state->uart_port->lock, flags);
+ uart_port_unlock(port, flags);
return ret;
}
@@ -593,14 +632,15 @@
return;
}
- port = state->uart_port;
pr_debug("uart_flush_buffer(%d) called\n", tty->index);
- spin_lock_irqsave(&port->lock, flags);
+ port = uart_port_lock(state, flags);
+ if (!port)
+ return;
uart_circ_clear(&state->xmit);
if (port->ops->flush_buffer)
port->ops->flush_buffer(port);
- spin_unlock_irqrestore(&port->lock, flags);
+ uart_port_unlock(port, flags);
tty_wakeup(tty);
}
@@ -611,9 +651,13 @@
static void uart_send_xchar(struct tty_struct *tty, char ch)
{
struct uart_state *state = tty->driver_data;
- struct uart_port *port = state->uart_port;
+ struct uart_port *port;
unsigned long flags;
+ port = uart_port_ref(state);
+ if (!port)
+ return;
+
if (port->ops->send_xchar)
port->ops->send_xchar(port, ch);
else {
@@ -623,14 +667,19 @@
port->ops->start_tx(port);
spin_unlock_irqrestore(&port->lock, flags);
}
+ uart_port_deref(port);
}
static void uart_throttle(struct tty_struct *tty)
{
struct uart_state *state = tty->driver_data;
- struct uart_port *port = state->uart_port;
+ struct uart_port *port;
upstat_t mask = 0;
+ port = uart_port_ref(state);
+ if (!port)
+ return;
+
if (I_IXOFF(tty))
mask |= UPSTAT_AUTOXOFF;
if (C_CRTSCTS(tty))
@@ -646,14 +695,20 @@
if (mask & UPSTAT_AUTOXOFF)
uart_send_xchar(tty, STOP_CHAR(tty));
+
+ uart_port_deref(port);
}
static void uart_unthrottle(struct tty_struct *tty)
{
struct uart_state *state = tty->driver_data;
- struct uart_port *port = state->uart_port;
+ struct uart_port *port;
upstat_t mask = 0;
+ port = uart_port_ref(state);
+ if (!port)
+ return;
+
if (I_IXOFF(tty))
mask |= UPSTAT_AUTOXOFF;
if (C_CRTSCTS(tty))
@@ -669,12 +724,15 @@
if (mask & UPSTAT_AUTOXOFF)
uart_send_xchar(tty, START_CHAR(tty));
+
+ uart_port_deref(port);
}
-static void uart_get_info(struct tty_port *port, struct serial_struct *retinfo)
+static int uart_get_info(struct tty_port *port, struct serial_struct *retinfo)
{
struct uart_state *state = container_of(port, struct uart_state, port);
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport;
+ int ret = -ENODEV;
memset(retinfo, 0, sizeof(*retinfo));
@@ -683,6 +741,10 @@
* occur as we go
*/
mutex_lock(&port->mutex);
+ uport = uart_port_check(state);
+ if (!uport)
+ goto out;
+
retinfo->type = uport->type;
retinfo->line = uport->line;
retinfo->port = uport->iobase;
@@ -701,7 +763,11 @@
retinfo->io_type = uport->iotype;
retinfo->iomem_reg_shift = uport->regshift;
retinfo->iomem_base = (void *)(unsigned long)uport->mapbase;
+
+ ret = 0;
+out:
mutex_unlock(&port->mutex);
+ return ret;
}
static int uart_get_info_user(struct tty_port *port,
@@ -709,7 +775,8 @@
{
struct serial_struct tmp;
- uart_get_info(port, &tmp);
+ if (uart_get_info(port, &tmp) < 0)
+ return -EIO;
if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
return -EFAULT;
@@ -720,13 +787,16 @@
struct uart_state *state,
struct serial_struct *new_info)
{
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport = uart_port_check(state);
unsigned long new_port;
unsigned int change_irq, change_port, closing_wait;
unsigned int old_custom_divisor, close_delay;
upf_t old_flags, new_flags;
int retval = 0;
+ if (!uport)
+ return -EIO;
+
new_port = new_info->port;
if (HIGH_BITS_OFFSET)
new_port += (unsigned long) new_info->port_high << HIGH_BITS_OFFSET;
@@ -886,7 +956,7 @@
retval = 0;
if (uport->type == PORT_UNKNOWN)
goto exit;
- if (port->flags & ASYNC_INITIALIZED) {
+ if (tty_port_initialized(port)) {
if (((old_flags ^ uport->flags) & UPF_SPD_MASK) ||
old_custom_divisor != uport->custom_divisor) {
/*
@@ -936,13 +1006,11 @@
* @tty: tty associated with the UART
* @state: UART being queried
* @value: returned modem value
- *
- * Note: uart_ioctl protects us against hangups.
*/
static int uart_get_lsr_info(struct tty_struct *tty,
struct uart_state *state, unsigned int __user *value)
{
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport = uart_port_check(state);
unsigned int result;
result = uport->ops->tx_empty(uport);
@@ -965,18 +1033,22 @@
{
struct uart_state *state = tty->driver_data;
struct tty_port *port = &state->port;
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport;
int result = -EIO;
mutex_lock(&port->mutex);
- if (!(tty->flags & (1 << TTY_IO_ERROR))) {
+ uport = uart_port_check(state);
+ if (!uport)
+ goto out;
+
+ if (!tty_io_error(tty)) {
result = uport->mctrl;
spin_lock_irq(&uport->lock);
result |= uport->ops->get_mctrl(uport);
spin_unlock_irq(&uport->lock);
}
+out:
mutex_unlock(&port->mutex);
-
return result;
}
@@ -984,15 +1056,20 @@
uart_tiocmset(struct tty_struct *tty, unsigned int set, unsigned int clear)
{
struct uart_state *state = tty->driver_data;
- struct uart_port *uport = state->uart_port;
struct tty_port *port = &state->port;
+ struct uart_port *uport;
int ret = -EIO;
mutex_lock(&port->mutex);
- if (!(tty->flags & (1 << TTY_IO_ERROR))) {
+ uport = uart_port_check(state);
+ if (!uport)
+ goto out;
+
+ if (!tty_io_error(tty)) {
uart_update_mctrl(uport, set, clear);
ret = 0;
}
+out:
mutex_unlock(&port->mutex);
return ret;
}
@@ -1001,21 +1078,26 @@
{
struct uart_state *state = tty->driver_data;
struct tty_port *port = &state->port;
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport;
+ int ret = -EIO;
mutex_lock(&port->mutex);
+ uport = uart_port_check(state);
+ if (!uport)
+ goto out;
if (uport->type != PORT_UNKNOWN)
uport->ops->break_ctl(uport, break_state);
-
+ ret = 0;
+out:
mutex_unlock(&port->mutex);
- return 0;
+ return ret;
}
static int uart_do_autoconfig(struct tty_struct *tty,struct uart_state *state)
{
- struct uart_port *uport = state->uart_port;
struct tty_port *port = &state->port;
+ struct uart_port *uport;
int flags, ret;
if (!capable(CAP_SYS_ADMIN))
@@ -1029,6 +1111,12 @@
if (mutex_lock_interruptible(&port->mutex))
return -ERESTARTSYS;
+ uport = uart_port_check(state);
+ if (!uport) {
+ ret = -EIO;
+ goto out;
+ }
+
ret = -EBUSY;
if (tty_port_users(port) == 1) {
uart_shutdown(tty, state);
@@ -1052,6 +1140,7 @@
ret = uart_startup(tty, state, 1);
}
+out:
mutex_unlock(&port->mutex);
return ret;
}
@@ -1074,10 +1163,9 @@
* FIXME: This wants extracting into a common all driver implementation
* of TIOCMWAIT using tty_port.
*/
-static int
-uart_wait_modem_status(struct uart_state *state, unsigned long arg)
+static int uart_wait_modem_status(struct uart_state *state, unsigned long arg)
{
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport;
struct tty_port *port = &state->port;
DECLARE_WAITQUEUE(wait, current);
struct uart_icount cprev, cnow;
@@ -1086,6 +1174,9 @@
/*
* note the counters on entry
*/
+ uport = uart_port_ref(state);
+ if (!uport)
+ return -EIO;
spin_lock_irq(&uport->lock);
memcpy(&cprev, &uport->icount, sizeof(struct uart_icount));
uart_enable_ms(uport);
@@ -1119,6 +1210,7 @@
}
__set_current_state(TASK_RUNNING);
remove_wait_queue(&port->delta_msr_wait, &wait);
+ uart_port_deref(uport);
return ret;
}
@@ -1134,11 +1226,15 @@
{
struct uart_state *state = tty->driver_data;
struct uart_icount cnow;
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport;
+ uport = uart_port_ref(state);
+ if (!uport)
+ return -EIO;
spin_lock_irq(&uport->lock);
memcpy(&cnow, &uport->icount, sizeof(struct uart_icount));
spin_unlock_irq(&uport->lock);
+ uart_port_deref(uport);
icount->cts = cnow.cts;
icount->dsr = cnow.dsr;
@@ -1200,11 +1296,11 @@
* Called via sys_ioctl. We can use spin_lock_irq() here.
*/
static int
-uart_ioctl(struct tty_struct *tty, unsigned int cmd,
- unsigned long arg)
+uart_ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg)
{
struct uart_state *state = tty->driver_data;
struct tty_port *port = &state->port;
+ struct uart_port *uport;
void __user *uarg = (void __user *)arg;
int ret = -ENOIOCTLCMD;
@@ -1238,7 +1334,7 @@
if (ret != -ENOIOCTLCMD)
goto out;
- if (tty->flags & (1 << TTY_IO_ERROR)) {
+ if (tty_io_error(tty)) {
ret = -EIO;
goto out;
}
@@ -1256,8 +1352,9 @@
goto out;
mutex_lock(&port->mutex);
+ uport = uart_port_check(state);
- if (tty->flags & (1 << TTY_IO_ERROR)) {
+ if (!uport || tty_io_error(tty)) {
ret = -EIO;
goto out_up;
}
@@ -1273,19 +1370,17 @@
break;
case TIOCGRS485:
- ret = uart_get_rs485_config(state->uart_port, uarg);
+ ret = uart_get_rs485_config(uport, uarg);
break;
case TIOCSRS485:
- ret = uart_set_rs485_config(state->uart_port, uarg);
+ ret = uart_set_rs485_config(uport, uarg);
break;
- default: {
- struct uart_port *uport = state->uart_port;
+ default:
if (uport->ops->ioctl)
ret = uport->ops->ioctl(uport, cmd, arg);
break;
}
- }
out_up:
mutex_unlock(&port->mutex);
out:
@@ -1295,24 +1390,29 @@
static void uart_set_ldisc(struct tty_struct *tty)
{
struct uart_state *state = tty->driver_data;
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport;
- if (uport->ops->set_ldisc) {
- mutex_lock(&state->port.mutex);
+ mutex_lock(&state->port.mutex);
+ uport = uart_port_check(state);
+ if (uport && uport->ops->set_ldisc)
uport->ops->set_ldisc(uport, &tty->termios);
- mutex_unlock(&state->port.mutex);
- }
+ mutex_unlock(&state->port.mutex);
}
static void uart_set_termios(struct tty_struct *tty,
struct ktermios *old_termios)
{
struct uart_state *state = tty->driver_data;
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport;
unsigned int cflag = tty->termios.c_cflag;
unsigned int iflag_mask = IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK;
bool sw_changed = false;
+ mutex_lock(&state->port.mutex);
+ uport = uart_port_check(state);
+ if (!uport)
+ goto out;
+
/*
* Drivers doing software flow control also need to know
* about changes to these input settings.
@@ -1335,12 +1435,10 @@
tty->termios.c_ispeed == old_termios->c_ispeed &&
((tty->termios.c_iflag ^ old_termios->c_iflag) & iflag_mask) == 0 &&
!sw_changed) {
- return;
+ goto out;
}
- mutex_lock(&state->port.mutex);
uart_change_speed(tty, state, old_termios);
- mutex_unlock(&state->port.mutex);
/* reload cflag from termios; port driver may have overriden flags */
cflag = tty->termios.c_cflag;
@@ -1350,17 +1448,18 @@
/* Handle transition away from B0 status */
else if (!(old_termios->c_cflag & CBAUD) && (cflag & CBAUD)) {
unsigned int mask = TIOCM_DTR;
- if (!(cflag & CRTSCTS) || !test_bit(TTY_THROTTLED, &tty->flags))
+ if (!(cflag & CRTSCTS) || !tty_throttled(tty))
mask |= TIOCM_RTS;
uart_set_mctrl(uport, mask);
}
+out:
+ mutex_unlock(&state->port.mutex);
}
/*
* Calls to uart_close() are serialised via the tty_lock in
* drivers/tty/tty_io.c:tty_release()
* drivers/tty/tty_io.c:do_tty_hangup()
- * This runs from a workqueue and can sleep for a _short_ time only.
*/
static void uart_close(struct tty_struct *tty, struct file *filp)
{
@@ -1379,18 +1478,21 @@
return;
}
- uport = state->uart_port;
port = &state->port;
pr_debug("uart_close(%d) called\n", tty->index);
- if (!port->count || tty_port_close_start(port, tty, filp) == 0)
+ if (tty_port_close_start(port, tty, filp) == 0)
return;
+ mutex_lock(&port->mutex);
+ uport = uart_port_check(state);
+
/*
* At this point, we stop accepting input. To do this, we
* disable the receive line status interrupts.
*/
- if (port->flags & ASYNC_INITIALIZED) {
+ if (tty_port_initialized(port) &&
+ !WARN(!uport, "detached port still initialized!\n")) {
spin_lock_irq(&uport->lock);
uport->ops->stop_rx(uport);
spin_unlock_irq(&uport->lock);
@@ -1402,7 +1504,6 @@
uart_wait_until_sent(tty, uport->timeout);
}
- mutex_lock(&port->mutex);
uart_shutdown(tty, state);
tty_port_tty_set(port, NULL);
@@ -1413,17 +1514,17 @@
if (port->close_delay)
msleep_interruptible(jiffies_to_msecs(port->close_delay));
spin_lock_irq(&port->lock);
- } else if (!uart_console(uport)) {
+ } else if (uport && !uart_console(uport)) {
spin_unlock_irq(&port->lock);
uart_change_pm(state, UART_PM_STATE_OFF);
spin_lock_irq(&port->lock);
}
+ spin_unlock_irq(&port->lock);
+ tty_port_set_active(port, 0);
/*
* Wake up anyone trying to open this port.
*/
- clear_bit(ASYNCB_NORMAL_ACTIVE, &port->flags);
- spin_unlock_irq(&port->lock);
wake_up_interruptible(&port->open_wait);
mutex_unlock(&port->mutex);
@@ -1435,11 +1536,14 @@
static void uart_wait_until_sent(struct tty_struct *tty, int timeout)
{
struct uart_state *state = tty->driver_data;
- struct uart_port *port = state->uart_port;
+ struct uart_port *port;
unsigned long char_time, expire;
- if (port->type == PORT_UNKNOWN || port->fifosize == 0)
+ port = uart_port_ref(state);
+ if (!port || port->type == PORT_UNKNOWN || port->fifosize == 0) {
+ uart_port_deref(port);
return;
+ }
/*
* Set the check interval to be 1/5 of the estimated time to
@@ -1485,6 +1589,7 @@
if (time_after(jiffies, expire))
break;
}
+ uart_port_deref(port);
}
/*
@@ -1496,20 +1601,24 @@
{
struct uart_state *state = tty->driver_data;
struct tty_port *port = &state->port;
+ struct uart_port *uport;
unsigned long flags;
pr_debug("uart_hangup(%d)\n", tty->index);
mutex_lock(&port->mutex);
- if (port->flags & ASYNC_NORMAL_ACTIVE) {
+ uport = uart_port_check(state);
+ WARN(!uport, "hangup of detached port!\n");
+
+ if (tty_port_active(port)) {
uart_flush_buffer(tty);
uart_shutdown(tty, state);
spin_lock_irqsave(&port->lock, flags);
port->count = 0;
- clear_bit(ASYNCB_NORMAL_ACTIVE, &port->flags);
spin_unlock_irqrestore(&port->lock, flags);
+ tty_port_set_active(port, 0);
tty_port_tty_set(port, NULL);
- if (!uart_console(state->uart_port))
+ if (uport && !uart_console(uport))
uart_change_pm(state, UART_PM_STATE_OFF);
wake_up_interruptible(&port->open_wait);
wake_up_interruptible(&port->delta_msr_wait);
@@ -1517,10 +1626,11 @@
mutex_unlock(&port->mutex);
}
+/* uport == NULL if uart_port has already been removed */
static void uart_port_shutdown(struct tty_port *port)
{
struct uart_state *state = container_of(port, struct uart_state, port);
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport = uart_port_check(state);
/*
* clear delta_msr_wait queue to avoid mem leaks: we may free
@@ -1534,23 +1644,36 @@
/*
* Free the IRQ and disable the port.
*/
- uport->ops->shutdown(uport);
+ if (uport)
+ uport->ops->shutdown(uport);
/*
* Ensure that the IRQ handler isn't running on another CPU.
*/
- synchronize_irq(uport->irq);
+ if (uport)
+ synchronize_irq(uport->irq);
}
static int uart_carrier_raised(struct tty_port *port)
{
struct uart_state *state = container_of(port, struct uart_state, port);
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport;
int mctrl;
+
+ uport = uart_port_ref(state);
+ /*
+ * Should never observe uport == NULL since checks for hangup should
+ * abort the tty_port_block_til_ready() loop before checking for carrier
+ * raised -- but report carrier raised if it does anyway so open will
+ * continue and not sleep
+ */
+ if (WARN_ON(!uport))
+ return 1;
spin_lock_irq(&uport->lock);
uart_enable_ms(uport);
mctrl = uport->ops->get_mctrl(uport);
spin_unlock_irq(&uport->lock);
+ uart_port_deref(uport);
if (mctrl & TIOCM_CAR)
return 1;
return 0;
@@ -1559,12 +1682,18 @@
static void uart_dtr_rts(struct tty_port *port, int onoff)
{
struct uart_state *state = container_of(port, struct uart_state, port);
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport;
+
+ uport = uart_port_ref(state);
+ if (!uport)
+ return;
if (onoff)
uart_set_mctrl(uport, TIOCM_DTR | TIOCM_RTS);
else
uart_clear_mctrl(uport, TIOCM_DTR | TIOCM_RTS);
+
+ uart_port_deref(uport);
}
/*
@@ -1583,6 +1712,7 @@
int retval, line = tty->index;
struct uart_state *state = drv->state + line;
struct tty_port *port = &state->port;
+ struct uart_port *uport;
pr_debug("uart_open(%d) called\n", line);
@@ -1602,15 +1732,15 @@
goto end;
}
- if (!state->uart_port || state->uart_port->flags & UPF_DEAD) {
+ uport = uart_port_check(state);
+ if (!uport || uport->flags & UPF_DEAD) {
retval = -ENXIO;
goto err_unlock;
}
tty->driver_data = state;
- state->uart_port->state = state;
- state->port.low_latency =
- (state->uart_port->flags & UPF_LOW_LATENCY) ? 1 : 0;
+ uport->state = state;
+ port->low_latency = (uport->flags & UPF_LOW_LATENCY) ? 1 : 0;
tty_port_tty_set(port, tty);
/*
@@ -1649,13 +1779,15 @@
struct uart_state *state = drv->state + i;
struct tty_port *port = &state->port;
enum uart_pm_state pm_state;
- struct uart_port *uport = state->uart_port;
+ struct uart_port *uport;
char stat_buf[32];
unsigned int status;
int mmio;
+ mutex_lock(&port->mutex);
+ uport = uart_port_check(state);
if (!uport)
- return;
+ goto out;
mmio = uport->iotype >= UPIO_MEM;
seq_printf(m, "%d: uart:%s %s%08llX irq:%d",
@@ -1667,11 +1799,10 @@
if (uport->type == PORT_UNKNOWN) {
seq_putc(m, '\n');
- return;
+ goto out;
}
if (capable(CAP_SYS_ADMIN)) {
- mutex_lock(&port->mutex);
pm_state = state->pm_state;
if (pm_state != UART_PM_STATE_ON)
uart_change_pm(state, UART_PM_STATE_ON);
@@ -1680,7 +1811,6 @@
spin_unlock_irq(&uport->lock);
if (pm_state != UART_PM_STATE_ON)
uart_change_pm(state, pm_state);
- mutex_unlock(&port->mutex);
seq_printf(m, " tx:%d rx:%d",
uport->icount.tx, uport->icount.rx);
@@ -1718,6 +1848,8 @@
seq_putc(m, '\n');
#undef STATBIT
#undef INFOBIT
+out:
+ mutex_unlock(&port->mutex);
}
static int uart_proc_show(struct seq_file *m, void *v)
@@ -1954,10 +2086,10 @@
static void uart_change_pm(struct uart_state *state,
enum uart_pm_state pm_state)
{
- struct uart_port *port = state->uart_port;
+ struct uart_port *port = uart_port_check(state);
if (state->pm_state != pm_state) {
- if (port->ops->pm)
+ if (port && port->ops->pm)
port->ops->pm(port, pm_state, state->pm_state);
state->pm_state = pm_state;
}
@@ -2003,12 +2135,12 @@
uport->suspended = 1;
- if (port->flags & ASYNC_INITIALIZED) {
+ if (tty_port_initialized(port)) {
const struct uart_ops *ops = uport->ops;
int tries;
- set_bit(ASYNCB_SUSPENDED, &port->flags);
- clear_bit(ASYNCB_INITIALIZED, &port->flags);
+ tty_port_set_suspended(port, 1);
+ tty_port_set_initialized(port, 0);
spin_lock_irq(&uport->lock);
ops->stop_tx(uport);
@@ -2088,7 +2220,7 @@
console_start(uport->cons);
}
- if (port->flags & ASYNC_SUSPENDED) {
+ if (tty_port_suspended(port)) {
const struct uart_ops *ops = uport->ops;
int ret;
@@ -2107,7 +2239,7 @@
ops->set_mctrl(uport, uport->mctrl);
ops->start_tx(uport);
spin_unlock_irq(&uport->lock);
- set_bit(ASYNCB_INITIALIZED, &port->flags);
+ tty_port_set_initialized(port, 1);
} else {
/*
* Failed to resume - maybe hardware went away?
@@ -2118,7 +2250,7 @@
}
}
- clear_bit(ASYNCB_SUSPENDED, &port->flags);
+ tty_port_set_suspended(port, 0);
}
mutex_unlock(&port->mutex);
@@ -2228,42 +2360,42 @@
{
struct uart_driver *drv = driver->driver_state;
struct uart_state *state = drv->state + line;
+ struct tty_port *tport;
struct uart_port *port;
int baud = 9600;
int bits = 8;
int parity = 'n';
int flow = 'n';
- int ret;
+ int ret = 0;
- if (!state || !state->uart_port)
+ if (!state)
return -1;
- port = state->uart_port;
- if (!(port->ops->poll_get_char && port->ops->poll_put_char))
- return -1;
+ tport = &state->port;
+ mutex_lock(&tport->mutex);
+
+ port = uart_port_check(state);
+ if (!port || !(port->ops->poll_get_char && port->ops->poll_put_char)) {
+ ret = -1;
+ goto out;
+ }
if (port->ops->poll_init) {
- struct tty_port *tport = &state->port;
-
- ret = 0;
- mutex_lock(&tport->mutex);
/*
- * We don't set ASYNCB_INITIALIZED as we only initialized the
- * hw, e.g. state->xmit is still uninitialized.
+ * We don't set initialized as we only initialized the hw,
+ * e.g. state->xmit is still uninitialized.
*/
- if (!test_bit(ASYNCB_INITIALIZED, &tport->flags))
+ if (!tty_port_initialized(tport))
ret = port->ops->poll_init(port);
- mutex_unlock(&tport->mutex);
- if (ret)
- return ret;
}
- if (options) {
+ if (!ret && options) {
uart_parse_options(options, &baud, &parity, &bits, &flow);
- return uart_set_options(port, NULL, baud, parity, bits, flow);
+ ret = uart_set_options(port, NULL, baud, parity, bits, flow);
}
-
- return 0;
+out:
+ mutex_unlock(&tport->mutex);
+ return ret;
}
static int uart_poll_get_char(struct tty_driver *driver, int line)
@@ -2271,12 +2403,15 @@
struct uart_driver *drv = driver->driver_state;
struct uart_state *state = drv->state + line;
struct uart_port *port;
+ int ret = -1;
- if (!state || !state->uart_port)
- return -1;
-
- port = state->uart_port;
- return port->ops->poll_get_char(port);
+ if (state) {
+ port = uart_port_ref(state);
+ if (port)
+ ret = port->ops->poll_get_char(port);
+ uart_port_deref(port);
+ }
+ return ret;
}
static void uart_poll_put_char(struct tty_driver *driver, int line, char ch)
@@ -2285,14 +2420,17 @@
struct uart_state *state = drv->state + line;
struct uart_port *port;
- if (!state || !state->uart_port)
+ if (!state)
return;
- port = state->uart_port;
+ port = uart_port_ref(state);
+ if (!port)
+ return;
if (ch == '\n')
port->ops->poll_put_char(port, '\r');
port->ops->poll_put_char(port, ch);
+ uart_port_deref(port);
}
#endif
@@ -2639,6 +2777,8 @@
}
/* Link the port to the driver state table and vice versa */
+ atomic_set(&state->refcount, 1);
+ init_waitqueue_head(&state->remove_wait);
state->uart_port = uport;
uport->state = state;
@@ -2711,15 +2851,12 @@
{
struct uart_state *state = drv->state + uport->line;
struct tty_port *port = &state->port;
+ struct uart_port *uart_port;
struct tty_struct *tty;
int ret = 0;
BUG_ON(in_interrupt());
- if (state->uart_port != uport)
- dev_alert(uport->dev, "Removing wrong port: %p != %p\n",
- state->uart_port, uport);
-
mutex_lock(&port_mutex);
/*
@@ -2727,7 +2864,12 @@
* succeeding while we shut down the port.
*/
mutex_lock(&port->mutex);
- if (!state->uart_port) {
+ uart_port = uart_port_check(state);
+ if (uart_port != uport)
+ dev_alert(uport->dev, "Removing wrong port: %p != %p\n",
+ uart_port, uport);
+
+ if (!uart_port) {
mutex_unlock(&port->mutex);
ret = -EINVAL;
goto out;
@@ -2764,7 +2906,11 @@
*/
uport->type = PORT_UNKNOWN;
+ mutex_lock(&port->mutex);
+ WARN_ON(atomic_dec_return(&state->refcount) < 0);
+ wait_event(state->remove_wait, !atomic_read(&state->refcount));
state->uart_port = NULL;
+ mutex_unlock(&port->mutex);
out:
mutex_unlock(&port_mutex);
diff --git a/drivers/tty/serial/serial_mctrl_gpio.c b/drivers/tty/serial/serial_mctrl_gpio.c
index 0214736..e8dd509 100644
--- a/drivers/tty/serial/serial_mctrl_gpio.c
+++ b/drivers/tty/serial/serial_mctrl_gpio.c
@@ -43,8 +43,6 @@
{ "rng", TIOCM_RNG, false, },
{ "rts", TIOCM_RTS, true, },
{ "dtr", TIOCM_DTR, true, },
- { "out1", TIOCM_OUT1, true, },
- { "out2", TIOCM_OUT2, true, },
};
void mctrl_gpio_set(struct mctrl_gpios *gpios, unsigned int mctrl)
@@ -125,9 +123,12 @@
struct uart_port *port = gpios->port;
u32 mctrl = gpios->mctrl_prev;
u32 mctrl_diff;
+ unsigned long flags;
mctrl_gpio_get(gpios, &mctrl);
+ spin_lock_irqsave(&port->lock, flags);
+
mctrl_diff = mctrl ^ gpios->mctrl_prev;
gpios->mctrl_prev = mctrl;
@@ -147,6 +148,8 @@
wake_up_interruptible(&port->state->port.delta_msr_wait);
}
+ spin_unlock_irqrestore(&port->lock, flags);
+
return IRQ_HANDLED;
}
diff --git a/drivers/tty/serial/serial_mctrl_gpio.h b/drivers/tty/serial/serial_mctrl_gpio.h
index bcfad5d..332a33a 100644
--- a/drivers/tty/serial/serial_mctrl_gpio.h
+++ b/drivers/tty/serial/serial_mctrl_gpio.h
@@ -32,8 +32,6 @@
UART_GPIO_RI = UART_GPIO_RNG,
UART_GPIO_RTS,
UART_GPIO_DTR,
- UART_GPIO_OUT1,
- UART_GPIO_OUT2,
UART_GPIO_MAX,
};
diff --git a/drivers/tty/serial/sirfsoc_uart.c b/drivers/tty/serial/sirfsoc_uart.c
index c6657de..b186c9c 100644
--- a/drivers/tty/serial/sirfsoc_uart.c
+++ b/drivers/tty/serial/sirfsoc_uart.c
@@ -1264,6 +1264,7 @@
static int sirfsoc_uart_probe(struct platform_device *pdev)
{
+ struct device_node *np = pdev->dev.of_node;
struct sirfsoc_uart_port *sirfport;
struct uart_port *port;
struct resource *res;
@@ -1276,13 +1277,13 @@
};
const struct of_device_id *match;
- match = of_match_node(sirfsoc_uart_ids, pdev->dev.of_node);
+ match = of_match_node(sirfsoc_uart_ids, np);
sirfport = devm_kzalloc(&pdev->dev, sizeof(*sirfport), GFP_KERNEL);
if (!sirfport) {
ret = -ENOMEM;
goto err;
}
- sirfport->port.line = of_alias_get_id(pdev->dev.of_node, "serial");
+ sirfport->port.line = of_alias_get_id(np, "serial");
sirf_ports[sirfport->port.line] = sirfport;
sirfport->port.iotype = UPIO_MEM;
sirfport->port.flags = UPF_BOOT_AUTOCONF;
@@ -1291,25 +1292,25 @@
port->private_data = sirfport;
sirfport->uart_reg = (struct sirfsoc_uart_register *)match->data;
- sirfport->hw_flow_ctrl = of_property_read_bool(pdev->dev.of_node,
- "sirf,uart-has-rtscts");
- if (of_device_is_compatible(pdev->dev.of_node, "sirf,prima2-uart") ||
- of_device_is_compatible(pdev->dev.of_node, "sirf,atlas7-uart"))
+ sirfport->hw_flow_ctrl =
+ of_property_read_bool(np, "uart-has-rtscts") ||
+ of_property_read_bool(np, "sirf,uart-has-rtscts") /* deprecated */;
+ if (of_device_is_compatible(np, "sirf,prima2-uart") ||
+ of_device_is_compatible(np, "sirf,atlas7-uart"))
sirfport->uart_reg->uart_type = SIRF_REAL_UART;
- if (of_device_is_compatible(pdev->dev.of_node,
- "sirf,prima2-usp-uart") || of_device_is_compatible(
- pdev->dev.of_node, "sirf,atlas7-usp-uart")) {
+ if (of_device_is_compatible(np, "sirf,prima2-usp-uart") ||
+ of_device_is_compatible(np, "sirf,atlas7-usp-uart")) {
sirfport->uart_reg->uart_type = SIRF_USP_UART;
if (!sirfport->hw_flow_ctrl)
goto usp_no_flow_control;
- if (of_find_property(pdev->dev.of_node, "cts-gpios", NULL))
- sirfport->cts_gpio = of_get_named_gpio(
- pdev->dev.of_node, "cts-gpios", 0);
+ if (of_find_property(np, "cts-gpios", NULL))
+ sirfport->cts_gpio =
+ of_get_named_gpio(np, "cts-gpios", 0);
else
sirfport->cts_gpio = -1;
- if (of_find_property(pdev->dev.of_node, "rts-gpios", NULL))
- sirfport->rts_gpio = of_get_named_gpio(
- pdev->dev.of_node, "rts-gpios", 0);
+ if (of_find_property(np, "rts-gpios", NULL))
+ sirfport->rts_gpio =
+ of_get_named_gpio(np, "rts-gpios", 0);
else
sirfport->rts_gpio = -1;
@@ -1336,13 +1337,11 @@
gpio_direction_output(sirfport->rts_gpio, 1);
}
usp_no_flow_control:
- if (of_device_is_compatible(pdev->dev.of_node, "sirf,atlas7-uart") ||
- of_device_is_compatible(pdev->dev.of_node, "sirf,atlas7-usp-uart"))
+ if (of_device_is_compatible(np, "sirf,atlas7-uart") ||
+ of_device_is_compatible(np, "sirf,atlas7-usp-uart"))
sirfport->is_atlas7 = true;
- if (of_property_read_u32(pdev->dev.of_node,
- "fifosize",
- &port->fifosize)) {
+ if (of_property_read_u32(np, "fifosize", &port->fifosize)) {
dev_err(&pdev->dev,
"Unable to find fifosize in uart node.\n");
ret = -EFAULT;
diff --git a/drivers/tty/serial/uartlite.c b/drivers/tty/serial/uartlite.c
index d08baa6..05089b6 100644
--- a/drivers/tty/serial/uartlite.c
+++ b/drivers/tty/serial/uartlite.c
@@ -72,7 +72,7 @@
iowrite32be(val, addr);
}
-static struct uartlite_reg_ops uartlite_be = {
+static const struct uartlite_reg_ops uartlite_be = {
.in = uartlite_inbe32,
.out = uartlite_outbe32,
};
@@ -87,21 +87,21 @@
iowrite32(val, addr);
}
-static struct uartlite_reg_ops uartlite_le = {
+static const struct uartlite_reg_ops uartlite_le = {
.in = uartlite_inle32,
.out = uartlite_outle32,
};
static inline u32 uart_in32(u32 offset, struct uart_port *port)
{
- struct uartlite_reg_ops *reg_ops = port->private_data;
+ const struct uartlite_reg_ops *reg_ops = port->private_data;
return reg_ops->in(port->membase + offset);
}
static inline void uart_out32(u32 val, u32 offset, struct uart_port *port)
{
- struct uartlite_reg_ops *reg_ops = port->private_data;
+ const struct uartlite_reg_ops *reg_ops = port->private_data;
reg_ops->out(val, port->membase + offset);
}
@@ -345,13 +345,13 @@
return -EBUSY;
}
- port->private_data = &uartlite_be;
+ port->private_data = (void *)&uartlite_be;
ret = uart_in32(ULITE_CONTROL, port);
uart_out32(ULITE_CONTROL_RST_TX, ULITE_CONTROL, port);
ret = uart_in32(ULITE_STATUS, port);
/* Endianess detection */
if ((ret & ULITE_STATUS_TXEMPTY) != ULITE_STATUS_TXEMPTY)
- port->private_data = &uartlite_le;
+ port->private_data = (void *)&uartlite_le;
return 0;
}
diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index 1a7dc3c..481eb29 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -1478,6 +1478,9 @@
.type = "serial",
.compatible = "ucc_uart",
},
+ {
+ .compatible = "fsl,t1040-ucc-uart",
+ },
{},
};
MODULE_DEVICE_TABLE(of, ucc_uart_match);
diff --git a/drivers/tty/synclink.c b/drivers/tty/synclink.c
index c8c7601..c13e27e 100644
--- a/drivers/tty/synclink.c
+++ b/drivers/tty/synclink.c
@@ -1340,7 +1340,7 @@
wake_up_interruptible(&info->status_event_wait_q);
wake_up_interruptible(&info->event_wait_q);
- if ( (info->port.flags & ASYNC_CHECK_CD) &&
+ if (tty_port_check_carrier(&info->port) &&
(status & MISCSTATUS_DCD_LATCHED) ) {
if ( debug_level >= DEBUG_LEVEL_ISR )
printk("%s CD now %s...", info->device_name,
@@ -1361,8 +1361,7 @@
if (status & MISCSTATUS_CTS) {
if ( debug_level >= DEBUG_LEVEL_ISR )
printk("CTS tx start...");
- if (info->port.tty)
- info->port.tty->hw_stopped = 0;
+ info->port.tty->hw_stopped = 0;
usc_start_transmitter(info);
info->pending_bh |= BH_TRANSMIT;
return;
@@ -1749,13 +1748,13 @@
static int startup(struct mgsl_struct * info)
{
int retval = 0;
-
+
if ( debug_level >= DEBUG_LEVEL_INFO )
printk("%s(%d):mgsl_startup(%s)\n",__FILE__,__LINE__,info->device_name);
-
- if (info->port.flags & ASYNC_INITIALIZED)
+
+ if (tty_port_initialized(&info->port))
return 0;
-
+
if (!info->xmit_buf) {
/* allocate a page of memory for a transmit buffer */
info->xmit_buf = (unsigned char *)get_zeroed_page(GFP_KERNEL);
@@ -1788,14 +1787,13 @@
/* program hardware for current parameters */
mgsl_change_params(info);
-
+
if (info->port.tty)
clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
- info->port.flags |= ASYNC_INITIALIZED;
-
+ tty_port_set_initialized(&info->port, 1);
+
return 0;
-
} /* end of startup() */
/* shutdown()
@@ -1808,8 +1806,8 @@
static void shutdown(struct mgsl_struct * info)
{
unsigned long flags;
-
- if (!(info->port.flags & ASYNC_INITIALIZED))
+
+ if (!tty_port_initialized(&info->port))
return;
if (debug_level >= DEBUG_LEVEL_INFO)
@@ -1853,13 +1851,12 @@
spin_unlock_irqrestore(&info->irq_spinlock,flags);
- mgsl_release_resources(info);
-
+ mgsl_release_resources(info);
+
if (info->port.tty)
set_bit(TTY_IO_ERROR, &info->port.tty->flags);
- info->port.flags &= ~ASYNC_INITIALIZED;
-
+ tty_port_set_initialized(&info->port, 0);
} /* end of shutdown() */
static void mgsl_program_hw(struct mgsl_struct *info)
@@ -1966,15 +1963,8 @@
}
info->timeout += HZ/50; /* Add .02 seconds of slop */
- if (cflag & CRTSCTS)
- info->port.flags |= ASYNC_CTS_FLOW;
- else
- info->port.flags &= ~ASYNC_CTS_FLOW;
-
- if (cflag & CLOCAL)
- info->port.flags &= ~ASYNC_CHECK_CD;
- else
- info->port.flags |= ASYNC_CHECK_CD;
+ tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
+ tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
/* process tty input control flags */
@@ -2972,7 +2962,7 @@
if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
(cmd != TIOCMIWAIT)) {
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
}
@@ -3049,7 +3039,7 @@
/* Handle transition away from B0 status */
if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) {
info->serial_signals |= SerialSignal_DTR;
- if (!C_CRTSCTS(tty) || !test_bit(TTY_THROTTLED, &tty->flags))
+ if (!C_CRTSCTS(tty) || !tty_throttled(tty))
info->serial_signals |= SerialSignal_RTS;
spin_lock_irqsave(&info->irq_spinlock,flags);
usc_set_serial_signals(info);
@@ -3091,7 +3081,7 @@
goto cleanup;
mutex_lock(&info->port.mutex);
- if (info->port.flags & ASYNC_INITIALIZED)
+ if (tty_port_initialized(&info->port))
mgsl_wait_until_sent(tty, info->timeout);
mgsl_flush_buffer(tty);
tty_ldisc_flush(tty);
@@ -3129,15 +3119,15 @@
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):mgsl_wait_until_sent(%s) entry\n",
__FILE__,__LINE__, info->device_name );
-
+
if (mgsl_paranoia_check(info, tty->name, "mgsl_wait_until_sent"))
return;
- if (!(info->port.flags & ASYNC_INITIALIZED))
+ if (!tty_port_initialized(&info->port))
goto exit;
-
+
orig_jiffies = jiffies;
-
+
/* Set check interval to 1/5 of estimated time to
* send a character, and make it at least 1. The check
* interval should also be less than the timeout.
@@ -3204,7 +3194,7 @@
shutdown(info);
info->port.count = 0;
- info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
+ tty_port_set_active(&info->port, 0);
info->port.tty = NULL;
wake_up_interruptible(&info->port.open_wait);
@@ -3270,9 +3260,9 @@
printk("%s(%d):block_til_ready on %s\n",
__FILE__,__LINE__, tty->driver->name );
- if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
+ if (filp->f_flags & O_NONBLOCK || tty_io_error(tty)) {
/* nonblock mode is set or port is not enabled */
- port->flags |= ASYNC_NORMAL_ACTIVE;
+ tty_port_set_active(port, 1);
return 0;
}
@@ -3297,14 +3287,14 @@
port->count--;
spin_unlock_irqrestore(&info->irq_spinlock, flags);
port->blocked_open++;
-
+
while (1) {
- if (C_BAUD(tty) && test_bit(ASYNCB_INITIALIZED, &port->flags))
+ if (C_BAUD(tty) && tty_port_initialized(port))
tty_port_raise_dtr_rts(port);
-
+
set_current_state(TASK_INTERRUPTIBLE);
-
- if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)){
+
+ if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
retval = (port->flags & ASYNC_HUP_NOTIFY) ?
-EAGAIN : -ERESTARTSYS;
break;
@@ -3341,7 +3331,7 @@
__FILE__,__LINE__, tty->driver->name, port->count );
if (!retval)
- port->flags |= ASYNC_NORMAL_ACTIVE;
+ tty_port_set_active(port, 1);
return retval;
diff --git a/drivers/tty/synclink_gt.c b/drivers/tty/synclink_gt.c
index d5b6471..7aca2d4 100644
--- a/drivers/tty/synclink_gt.c
+++ b/drivers/tty/synclink_gt.c
@@ -726,7 +726,7 @@
goto cleanup;
mutex_lock(&info->port.mutex);
- if (info->port.flags & ASYNC_INITIALIZED)
+ if (tty_port_initialized(&info->port))
wait_until_sent(tty, info->timeout);
flush_buffer(tty);
tty_ldisc_flush(tty);
@@ -756,9 +756,9 @@
spin_lock_irqsave(&info->port.lock, flags);
info->port.count = 0;
- info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
info->port.tty = NULL;
spin_unlock_irqrestore(&info->port.lock, flags);
+ tty_port_set_active(&info->port, 0);
mutex_unlock(&info->port.mutex);
wake_up_interruptible(&info->port.open_wait);
@@ -784,7 +784,7 @@
/* Handle transition away from B0 status */
if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) {
info->signals |= SerialSignal_DTR;
- if (!C_CRTSCTS(tty) || !test_bit(TTY_THROTTLED, &tty->flags))
+ if (!C_CRTSCTS(tty) || !tty_throttled(tty))
info->signals |= SerialSignal_RTS;
spin_lock_irqsave(&info->lock,flags);
set_signals(info);
@@ -893,7 +893,7 @@
if (sanity_check(info, tty->name, "wait_until_sent"))
return;
DBGINFO(("%s wait_until_sent entry\n", info->device_name));
- if (!(info->port.flags & ASYNC_INITIALIZED))
+ if (!tty_port_initialized(&info->port))
goto exit;
orig_jiffies = jiffies;
@@ -1032,7 +1032,7 @@
if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
(cmd != TIOCMIWAIT)) {
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
}
@@ -2080,7 +2080,7 @@
wake_up_interruptible(&info->event_wait_q);
info->pending_bh |= BH_STATUS;
- if (info->port.flags & ASYNC_CHECK_CD) {
+ if (tty_port_check_carrier(&info->port)) {
if (info->signals & SerialSignal_DCD)
wake_up_interruptible(&info->port.open_wait);
else {
@@ -2421,7 +2421,7 @@
{
DBGINFO(("%s startup\n", info->device_name));
- if (info->port.flags & ASYNC_INITIALIZED)
+ if (tty_port_initialized(&info->port))
return 0;
if (!info->tx_buf) {
@@ -2442,7 +2442,7 @@
if (info->port.tty)
clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
- info->port.flags |= ASYNC_INITIALIZED;
+ tty_port_set_initialized(&info->port, 1);
return 0;
}
@@ -2454,7 +2454,7 @@
{
unsigned long flags;
- if (!(info->port.flags & ASYNC_INITIALIZED))
+ if (!tty_port_initialized(&info->port))
return;
DBGINFO(("%s shutdown\n", info->device_name));
@@ -2489,7 +2489,7 @@
if (info->port.tty)
set_bit(TTY_IO_ERROR, &info->port.tty->flags);
- info->port.flags &= ~ASYNC_INITIALIZED;
+ tty_port_set_initialized(&info->port, 0);
}
static void program_hw(struct slgt_info *info)
@@ -2576,15 +2576,8 @@
}
info->timeout += HZ/50; /* Add .02 seconds of slop */
- if (cflag & CRTSCTS)
- info->port.flags |= ASYNC_CTS_FLOW;
- else
- info->port.flags &= ~ASYNC_CTS_FLOW;
-
- if (cflag & CLOCAL)
- info->port.flags &= ~ASYNC_CHECK_CD;
- else
- info->port.flags |= ASYNC_CHECK_CD;
+ tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
+ tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
/* process tty input control flags */
@@ -3269,9 +3262,9 @@
DBGINFO(("%s block_til_ready\n", tty->driver->name));
- if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
+ if (filp->f_flags & O_NONBLOCK || tty_io_error(tty)) {
/* nonblock mode is set or port is not enabled */
- port->flags |= ASYNC_NORMAL_ACTIVE;
+ tty_port_set_active(port, 1);
return 0;
}
@@ -3294,12 +3287,12 @@
port->blocked_open++;
while (1) {
- if (C_BAUD(tty) && test_bit(ASYNCB_INITIALIZED, &port->flags))
+ if (C_BAUD(tty) && tty_port_initialized(port))
tty_port_raise_dtr_rts(port);
set_current_state(TASK_INTERRUPTIBLE);
- if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)){
+ if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
retval = (port->flags & ASYNC_HUP_NOTIFY) ?
-EAGAIN : -ERESTARTSYS;
break;
@@ -3328,7 +3321,7 @@
port->blocked_open--;
if (!retval)
- port->flags |= ASYNC_NORMAL_ACTIVE;
+ tty_port_set_active(port, 1);
DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
return retval;
diff --git a/drivers/tty/synclinkmp.c b/drivers/tty/synclinkmp.c
index 3f89685..dec1565 100644
--- a/drivers/tty/synclinkmp.c
+++ b/drivers/tty/synclinkmp.c
@@ -812,7 +812,7 @@
goto cleanup;
mutex_lock(&info->port.mutex);
- if (info->port.flags & ASYNC_INITIALIZED)
+ if (tty_port_initialized(&info->port))
wait_until_sent(tty, info->timeout);
flush_buffer(tty);
@@ -849,9 +849,9 @@
spin_lock_irqsave(&info->port.lock, flags);
info->port.count = 0;
- info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
info->port.tty = NULL;
spin_unlock_irqrestore(&info->port.lock, flags);
+ tty_port_set_active(&info->port, 1);
mutex_unlock(&info->port.mutex);
wake_up_interruptible(&info->port.open_wait);
@@ -881,7 +881,7 @@
/* Handle transition away from B0 status */
if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) {
info->serial_signals |= SerialSignal_DTR;
- if (!C_CRTSCTS(tty) || !test_bit(TTY_THROTTLED, &tty->flags))
+ if (!C_CRTSCTS(tty) || !tty_throttled(tty))
info->serial_signals |= SerialSignal_RTS;
spin_lock_irqsave(&info->lock,flags);
set_signals(info);
@@ -1061,7 +1061,7 @@
if (sanity_check(info, tty->name, "wait_until_sent"))
return;
- if (!test_bit(ASYNCB_INITIALIZED, &info->port.flags))
+ if (!tty_port_initialized(&info->port))
goto exit;
orig_jiffies = jiffies;
@@ -1261,7 +1261,7 @@
if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
(cmd != TIOCMIWAIT)) {
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
}
@@ -2463,7 +2463,7 @@
wake_up_interruptible(&info->status_event_wait_q);
wake_up_interruptible(&info->event_wait_q);
- if ( (info->port.flags & ASYNC_CHECK_CD) &&
+ if (tty_port_check_carrier(&info->port) &&
(status & MISCSTATUS_DCD_LATCHED) ) {
if ( debug_level >= DEBUG_LEVEL_ISR )
printk("%s CD now %s...", info->device_name,
@@ -2636,7 +2636,7 @@
if ( debug_level >= DEBUG_LEVEL_INFO )
printk("%s(%d):%s tx_releaseup()\n",__FILE__,__LINE__,info->device_name);
- if (info->port.flags & ASYNC_INITIALIZED)
+ if (tty_port_initialized(&info->port))
return 0;
if (!info->tx_buf) {
@@ -2662,7 +2662,7 @@
if (info->port.tty)
clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
- info->port.flags |= ASYNC_INITIALIZED;
+ tty_port_set_initialized(&info->port, 1);
return 0;
}
@@ -2673,7 +2673,7 @@
{
unsigned long flags;
- if (!(info->port.flags & ASYNC_INITIALIZED))
+ if (!tty_port_initialized(&info->port))
return;
if (debug_level >= DEBUG_LEVEL_INFO)
@@ -2705,7 +2705,7 @@
if (info->port.tty)
set_bit(TTY_IO_ERROR, &info->port.tty->flags);
- info->port.flags &= ~ASYNC_INITIALIZED;
+ tty_port_set_initialized(&info->port, 0);
}
static void program_hw(SLMP_INFO *info)
@@ -2813,15 +2813,8 @@
}
info->timeout += HZ/50; /* Add .02 seconds of slop */
- if (cflag & CRTSCTS)
- info->port.flags |= ASYNC_CTS_FLOW;
- else
- info->port.flags &= ~ASYNC_CTS_FLOW;
-
- if (cflag & CLOCAL)
- info->port.flags &= ~ASYNC_CHECK_CD;
- else
- info->port.flags |= ASYNC_CHECK_CD;
+ tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
+ tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
/* process tty input control flags */
@@ -3285,10 +3278,10 @@
printk("%s(%d):%s block_til_ready()\n",
__FILE__,__LINE__, tty->driver->name );
- if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
+ if (filp->f_flags & O_NONBLOCK || tty_io_error(tty)) {
/* nonblock mode is set or port is not enabled */
/* just verify that callout device is not active */
- port->flags |= ASYNC_NORMAL_ACTIVE;
+ tty_port_set_active(port, 1);
return 0;
}
@@ -3315,12 +3308,12 @@
port->blocked_open++;
while (1) {
- if (C_BAUD(tty) && test_bit(ASYNCB_INITIALIZED, &port->flags))
+ if (C_BAUD(tty) && tty_port_initialized(port))
tty_port_raise_dtr_rts(port);
set_current_state(TASK_INTERRUPTIBLE);
- if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)){
+ if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
retval = (port->flags & ASYNC_HUP_NOTIFY) ?
-EAGAIN : -ERESTARTSYS;
break;
@@ -3355,7 +3348,7 @@
__FILE__,__LINE__, tty->driver->name, port->count );
if (!retval)
- port->flags |= ASYNC_NORMAL_ACTIVE;
+ tty_port_set_active(port, 1);
return retval;
}
diff --git a/drivers/tty/tty_buffer.c b/drivers/tty/tty_buffer.c
index a946e49..aa80dc9 100644
--- a/drivers/tty/tty_buffer.c
+++ b/drivers/tty/tty_buffer.c
@@ -37,29 +37,6 @@
#define TTY_BUFFER_PAGE (((PAGE_SIZE - sizeof(struct tty_buffer)) / 2) & ~0xFF)
-/*
- * If all tty flip buffers have been processed by flush_to_ldisc() or
- * dropped by tty_buffer_flush(), check if the linked pty has been closed.
- * If so, wake the reader/poll to process
- */
-static inline void check_other_closed(struct tty_struct *tty)
-{
- unsigned long flags, old;
-
- /* transition from TTY_OTHER_CLOSED => TTY_OTHER_DONE must be atomic */
- for (flags = ACCESS_ONCE(tty->flags);
- test_bit(TTY_OTHER_CLOSED, &flags);
- ) {
- old = flags;
- __set_bit(TTY_OTHER_DONE, &flags);
- flags = cmpxchg(&tty->flags, old, flags);
- if (old == flags) {
- wake_up_interruptible(&tty->read_wait);
- break;
- }
- }
-}
-
/**
* tty_buffer_lock_exclusive - gain exclusive access to buffer
* tty_buffer_unlock_exclusive - release exclusive access
@@ -254,8 +231,6 @@
if (ld && ld->ops->flush_buffer)
ld->ops->flush_buffer(tty);
- check_other_closed(tty);
-
atomic_dec(&buf->priority);
mutex_unlock(&buf->lock);
}
@@ -522,10 +497,8 @@
*/
count = smp_load_acquire(&head->commit) - head->read;
if (!count) {
- if (next == NULL) {
- check_other_closed(tty);
+ if (next == NULL)
break;
- }
buf->head = next;
tty_buffer_free(port, head);
continue;
@@ -614,3 +587,8 @@
{
return cancel_work_sync(&port->buf.work);
}
+
+void tty_buffer_flush_work(struct tty_port *port)
+{
+ flush_work(&port->buf.work);
+}
diff --git a/drivers/tty/tty_io.c b/drivers/tty/tty_io.c
index 24d5491..734a635 100644
--- a/drivers/tty/tty_io.c
+++ b/drivers/tty/tty_io.c
@@ -230,9 +230,6 @@
tty_free_file(file);
}
-
-#define TTY_NUMBER(tty) ((tty)->index + (tty)->driver->name_base)
-
/**
* tty_name - return tty naming
* @tty: tty structure
@@ -1070,7 +1067,7 @@
if (tty_paranoia_check(tty, inode, "tty_read"))
return -EIO;
- if (!tty || (test_bit(TTY_IO_ERROR, &tty->flags)))
+ if (!tty || tty_io_error(tty))
return -EIO;
/* We want to wait for the line discipline to sort out in this
@@ -1245,8 +1242,7 @@
if (tty_paranoia_check(tty, file_inode(file), "tty_write"))
return -EIO;
- if (!tty || !tty->ops->write ||
- (test_bit(TTY_IO_ERROR, &tty->flags)))
+ if (!tty || !tty->ops->write || tty_io_error(tty))
return -EIO;
/* Short term debug to catch buggy drivers */
if (tty->ops->write_room == NULL)
@@ -1964,7 +1960,6 @@
* tty_lookup_driver - lookup a tty driver for a given device file
* @device: device number
* @filp: file pointer to tty
- * @noctty: set if the device should not become a controlling tty
* @index: index for the device in the @return driver
* @return: driver for this inode (with increased refcount)
*
diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c
index 23bf5bb..bf36ac9 100644
--- a/drivers/tty/tty_ioctl.c
+++ b/drivers/tty/tty_ioctl.c
@@ -158,7 +158,7 @@
int ret = 0;
mutex_lock(&tty->throttle_mutex);
- if (!test_bit(TTY_THROTTLED, &tty->flags)) {
+ if (!tty_throttled(tty)) {
if (tty->flow_change != TTY_THROTTLE_SAFE)
ret = 1;
else {
@@ -189,7 +189,7 @@
int ret = 0;
mutex_lock(&tty->throttle_mutex);
- if (test_bit(TTY_THROTTLED, &tty->flags)) {
+ if (tty_throttled(tty)) {
if (tty->flow_change != TTY_UNTHROTTLE_SAFE)
ret = 1;
else {
diff --git a/drivers/tty/tty_port.c b/drivers/tty/tty_port.c
index dbcca30..c3f9d93 100644
--- a/drivers/tty/tty_port.c
+++ b/drivers/tty/tty_port.c
@@ -204,7 +204,8 @@
if (port->console)
goto out;
- if (test_and_clear_bit(ASYNCB_INITIALIZED, &port->flags)) {
+ if (tty_port_initialized(port)) {
+ tty_port_set_initialized(port, 0);
/*
* Drop DTR/RTS if HUPCL is set. This causes any attached
* modem to hang up the line.
@@ -236,12 +237,12 @@
spin_lock_irqsave(&port->lock, flags);
port->count = 0;
- port->flags &= ~ASYNC_NORMAL_ACTIVE;
tty = port->tty;
if (tty)
set_bit(TTY_IO_ERROR, &tty->flags);
port->tty = NULL;
spin_unlock_irqrestore(&port->lock, flags);
+ tty_port_set_active(port, 0);
tty_port_shutdown(port, tty);
tty_kref_put(tty);
wake_up_interruptible(&port->open_wait);
@@ -364,15 +365,15 @@
/* if non-blocking mode is set we can pass directly to open unless
the port has just hung up or is in another error state */
- if (tty->flags & (1 << TTY_IO_ERROR)) {
- port->flags |= ASYNC_NORMAL_ACTIVE;
+ if (tty_io_error(tty)) {
+ tty_port_set_active(port, 1);
return 0;
}
if (filp->f_flags & O_NONBLOCK) {
/* Indicate we are open */
if (C_BAUD(tty))
tty_port_raise_dtr_rts(port);
- port->flags |= ASYNC_NORMAL_ACTIVE;
+ tty_port_set_active(port, 1);
return 0;
}
@@ -393,13 +394,13 @@
while (1) {
/* Indicate we are open */
- if (C_BAUD(tty) && test_bit(ASYNCB_INITIALIZED, &port->flags))
+ if (C_BAUD(tty) && tty_port_initialized(port))
tty_port_raise_dtr_rts(port);
prepare_to_wait(&port->open_wait, &wait, TASK_INTERRUPTIBLE);
/* Check for a hangup or uninitialised port.
Return accordingly */
- if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)) {
+ if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
if (port->flags & ASYNC_HUP_NOTIFY)
retval = -EAGAIN;
else
@@ -430,9 +431,9 @@
if (!tty_hung_up_p(filp))
port->count++;
port->blocked_open--;
- if (retval == 0)
- port->flags |= ASYNC_NORMAL_ACTIVE;
spin_unlock_irqrestore(&port->lock, flags);
+ if (retval == 0)
+ tty_port_set_active(port, 1);
return retval;
}
EXPORT_SYMBOL(tty_port_block_til_ready);
@@ -480,7 +481,7 @@
tty->closing = 1;
- if (test_bit(ASYNCB_INITIALIZED, &port->flags)) {
+ if (tty_port_initialized(port)) {
/* Don't block on a stalled port, just pull the chain */
if (tty->flow_stopped)
tty_driver_flush_buffer(tty);
@@ -514,8 +515,8 @@
spin_lock_irqsave(&port->lock, flags);
wake_up_interruptible(&port->open_wait);
}
- port->flags &= ~ASYNC_NORMAL_ACTIVE;
spin_unlock_irqrestore(&port->lock, flags);
+ tty_port_set_active(port, 0);
}
EXPORT_SYMBOL(tty_port_close_end);
@@ -578,7 +579,7 @@
mutex_lock(&port->mutex);
- if (!test_bit(ASYNCB_INITIALIZED, &port->flags)) {
+ if (!tty_port_initialized(port)) {
clear_bit(TTY_IO_ERROR, &tty->flags);
if (port->ops->activate) {
int retval = port->ops->activate(port, tty);
@@ -587,7 +588,7 @@
return retval;
}
}
- set_bit(ASYNCB_INITIALIZED, &port->flags);
+ tty_port_set_initialized(port, 1);
}
mutex_unlock(&port->mutex);
return tty_port_block_til_ready(port, tty, filp);
diff --git a/drivers/tty/vt/selection.c b/drivers/tty/vt/selection.c
index 4dd9dd2..368ce18 100644
--- a/drivers/tty/vt/selection.c
+++ b/drivers/tty/vt/selection.c
@@ -354,7 +354,7 @@
add_wait_queue(&vc->paste_wait, &wait);
while (sel_buffer && sel_buffer_lth > pasted) {
set_current_state(TASK_INTERRUPTIBLE);
- if (test_bit(TTY_THROTTLED, &tty->flags)) {
+ if (tty_throttled(tty)) {
schedule();
continue;
}
diff --git a/drivers/tty/vt/vt.c b/drivers/tty/vt/vt.c
index 3e3c757..dc12532 100644
--- a/drivers/tty/vt/vt.c
+++ b/drivers/tty/vt/vt.c
@@ -760,50 +760,54 @@
int vc_allocate(unsigned int currcons) /* return 0 on success */
{
+ struct vt_notifier_param param;
+ struct vc_data *vc;
+
WARN_CONSOLE_UNLOCKED();
if (currcons >= MAX_NR_CONSOLES)
return -ENXIO;
- if (!vc_cons[currcons].d) {
- struct vc_data *vc;
- struct vt_notifier_param param;
- /* prevent users from taking too much memory */
- if (currcons >= MAX_NR_USER_CONSOLES && !capable(CAP_SYS_RESOURCE))
- return -EPERM;
+ if (vc_cons[currcons].d)
+ return 0;
- /* due to the granularity of kmalloc, we waste some memory here */
- /* the alloc is done in two steps, to optimize the common situation
- of a 25x80 console (structsize=216, screenbuf_size=4000) */
- /* although the numbers above are not valid since long ago, the
- point is still up-to-date and the comment still has its value
- even if only as a historical artifact. --mj, July 1998 */
- param.vc = vc = kzalloc(sizeof(struct vc_data), GFP_KERNEL);
- if (!vc)
+ /* due to the granularity of kmalloc, we waste some memory here */
+ /* the alloc is done in two steps, to optimize the common situation
+ of a 25x80 console (structsize=216, screenbuf_size=4000) */
+ /* although the numbers above are not valid since long ago, the
+ point is still up-to-date and the comment still has its value
+ even if only as a historical artifact. --mj, July 1998 */
+ param.vc = vc = kzalloc(sizeof(struct vc_data), GFP_KERNEL);
+ if (!vc)
return -ENOMEM;
- vc_cons[currcons].d = vc;
- tty_port_init(&vc->port);
- INIT_WORK(&vc_cons[currcons].SAK_work, vc_SAK);
- visual_init(vc, currcons, 1);
- if (!*vc->vc_uni_pagedir_loc)
+
+ vc_cons[currcons].d = vc;
+ tty_port_init(&vc->port);
+ INIT_WORK(&vc_cons[currcons].SAK_work, vc_SAK);
+
+ visual_init(vc, currcons, 1);
+
+ if (!*vc->vc_uni_pagedir_loc)
con_set_default_unimap(vc);
- vc->vc_screenbuf = kmalloc(vc->vc_screenbuf_size, GFP_KERNEL);
- if (!vc->vc_screenbuf) {
- kfree(vc);
- vc_cons[currcons].d = NULL;
- return -ENOMEM;
- }
- /* If no drivers have overridden us and the user didn't pass a
- boot option, default to displaying the cursor */
- if (global_cursor_default == -1)
- global_cursor_default = 1;
+ vc->vc_screenbuf = kmalloc(vc->vc_screenbuf_size, GFP_KERNEL);
+ if (!vc->vc_screenbuf)
+ goto err_free;
- vc_init(vc, vc->vc_rows, vc->vc_cols, 1);
- vcs_make_sysfs(currcons);
- atomic_notifier_call_chain(&vt_notifier_list, VT_ALLOCATE, ¶m);
- }
+ /* If no drivers have overridden us and the user didn't pass a
+ boot option, default to displaying the cursor */
+ if (global_cursor_default == -1)
+ global_cursor_default = 1;
+
+ vc_init(vc, vc->vc_rows, vc->vc_cols, 1);
+ vcs_make_sysfs(currcons);
+ atomic_notifier_call_chain(&vt_notifier_list, VT_ALLOCATE, ¶m);
+
return 0;
+err_free:
+ kfree(vc);
+ vc_cons[currcons].d = NULL;
+ return -ENOMEM;
}
static inline int resize_screen(struct vc_data *vc, int width, int height,
@@ -1035,20 +1039,27 @@
#define VT100ID "\033[?1;2c"
#define VT102ID "\033[?6c"
-unsigned char color_table[] = { 0, 4, 2, 6, 1, 5, 3, 7,
+const unsigned char color_table[] = { 0, 4, 2, 6, 1, 5, 3, 7,
8,12,10,14, 9,13,11,15 };
/* the default colour table, for VGA+ colour systems */
-int default_red[] = {0x00,0xaa,0x00,0xaa,0x00,0xaa,0x00,0xaa,
- 0x55,0xff,0x55,0xff,0x55,0xff,0x55,0xff};
-int default_grn[] = {0x00,0x00,0xaa,0x55,0x00,0x00,0xaa,0xaa,
- 0x55,0x55,0xff,0xff,0x55,0x55,0xff,0xff};
-int default_blu[] = {0x00,0x00,0x00,0x00,0xaa,0xaa,0xaa,0xaa,
- 0x55,0x55,0x55,0x55,0xff,0xff,0xff,0xff};
+unsigned char default_red[] = {
+ 0x00, 0xaa, 0x00, 0xaa, 0x00, 0xaa, 0x00, 0xaa,
+ 0x55, 0xff, 0x55, 0xff, 0x55, 0xff, 0x55, 0xff
+};
+module_param_array(default_red, byte, NULL, S_IRUGO | S_IWUSR);
-module_param_array(default_red, int, NULL, S_IRUGO | S_IWUSR);
-module_param_array(default_grn, int, NULL, S_IRUGO | S_IWUSR);
-module_param_array(default_blu, int, NULL, S_IRUGO | S_IWUSR);
+unsigned char default_grn[] = {
+ 0x00, 0x00, 0xaa, 0x55, 0x00, 0x00, 0xaa, 0xaa,
+ 0x55, 0x55, 0xff, 0xff, 0x55, 0x55, 0xff, 0xff
+};
+module_param_array(default_grn, byte, NULL, S_IRUGO | S_IWUSR);
+
+unsigned char default_blu[] = {
+ 0x00, 0x00, 0x00, 0x00, 0xaa, 0xaa, 0xaa, 0xaa,
+ 0x55, 0x55, 0x55, 0x55, 0xff, 0xff, 0xff, 0xff
+};
+module_param_array(default_blu, byte, NULL, S_IRUGO | S_IWUSR);
/*
* gotoxy() must verify all boundaries, because the arguments
@@ -3564,7 +3575,7 @@
struct module *owner = csw->owner;
struct con_driver *con_driver;
const char *desc;
- int i, retval = 0;
+ int i, retval;
WARN_CONSOLE_UNLOCKED();
@@ -3575,17 +3586,17 @@
con_driver = ®istered_con_driver[i];
/* already registered */
- if (con_driver->con == csw)
+ if (con_driver->con == csw) {
retval = -EBUSY;
+ goto err;
+ }
}
- if (retval)
- goto err;
-
desc = csw->con_startup();
-
- if (!desc)
+ if (!desc) {
+ retval = -ENODEV;
goto err;
+ }
retval = -EINVAL;
diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
index a6c4a1b..94a14f5 100644
--- a/drivers/usb/class/cdc-acm.c
+++ b/drivers/usb/class/cdc-acm.c
@@ -1680,7 +1680,7 @@
if (--acm->susp_count)
goto out;
- if (test_bit(ASYNCB_INITIALIZED, &acm->port.flags)) {
+ if (tty_port_initialized(&acm->port)) {
rv = usb_submit_urb(acm->ctrlurb, GFP_ATOMIC);
for (;;) {
@@ -1710,7 +1710,7 @@
{
struct acm *acm = usb_get_intfdata(intf);
- if (test_bit(ASYNCB_INITIALIZED, &acm->port.flags))
+ if (tty_port_initialized(&acm->port))
tty_port_tty_hangup(&acm->port, false);
return acm_resume(intf);
diff --git a/drivers/usb/gadget/function/u_serial.c b/drivers/usb/gadget/function/u_serial.c
index 6af145f..3580f19 100644
--- a/drivers/usb/gadget/function/u_serial.c
+++ b/drivers/usb/gadget/function/u_serial.c
@@ -512,7 +512,7 @@
req = list_first_entry(queue, struct usb_request, list);
/* leave data queued if tty was rx throttled */
- if (tty && test_bit(TTY_THROTTLED, &tty->flags))
+ if (tty && tty_throttled(tty))
break;
switch (req->status) {
@@ -579,7 +579,7 @@
* from starving ... but it's not clear that case ever happens.
*/
if (!list_empty(queue) && tty) {
- if (!test_bit(TTY_THROTTLED, &tty->flags)) {
+ if (!tty_throttled(tty)) {
if (do_push)
tasklet_schedule(&port->push);
else
diff --git a/drivers/usb/misc/sisusbvga/sisusb_con.c b/drivers/usb/misc/sisusbvga/sisusb_con.c
index ace3430..afa8532 100644
--- a/drivers/usb/misc/sisusbvga/sisusb_con.c
+++ b/drivers/usb/misc/sisusbvga/sisusb_con.c
@@ -601,7 +601,7 @@
/* interface routine */
static int
-sisusbcon_set_palette(struct vc_data *c, unsigned char *table)
+sisusbcon_set_palette(struct vc_data *c, const unsigned char *table)
{
struct sisusb_usb_data *sisusb;
int i, j;
diff --git a/drivers/usb/serial/console.c b/drivers/usb/serial/console.c
index a66b01b..8967715 100644
--- a/drivers/usb/serial/console.c
+++ b/drivers/usb/serial/console.c
@@ -127,7 +127,7 @@
info->port = port;
++port->port.count;
- if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags)) {
+ if (!tty_port_initialized(&port->port)) {
if (serial->type->set_termios) {
/*
* allocate a fake tty so the driver can initialize
@@ -168,7 +168,7 @@
tty_port_tty_set(&port->port, NULL);
tty_kref_put(tty);
}
- set_bit(ASYNCB_INITIALIZED, &port->port.flags);
+ tty_port_set_initialized(&port->port, 1);
}
/* Now that any required fake tty operations are completed restore
* the tty port count */
diff --git a/drivers/usb/serial/digi_acceleport.c b/drivers/usb/serial/digi_acceleport.c
index 16e8e37..6a1df9e 100644
--- a/drivers/usb/serial/digi_acceleport.c
+++ b/drivers/usb/serial/digi_acceleport.c
@@ -699,8 +699,7 @@
/* don't set RTS if using hardware flow control */
/* and throttling input */
modem_signals = TIOCM_DTR;
- if (!C_CRTSCTS(tty) ||
- !test_bit(TTY_THROTTLED, &tty->flags))
+ if (!C_CRTSCTS(tty) || !tty_throttled(tty))
modem_signals |= TIOCM_RTS;
digi_set_modem_signals(port, modem_signals, 1);
}
diff --git a/drivers/usb/serial/generic.c b/drivers/usb/serial/generic.c
index 54e170d..ae8c036 100644
--- a/drivers/usb/serial/generic.c
+++ b/drivers/usb/serial/generic.c
@@ -473,7 +473,7 @@
* Use tty-port initialised flag to detect all hangups including the
* one generated at USB-device disconnect.
*/
- if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags))
+ if (!tty_port_initialized(&port->port))
return true;
spin_lock_irqsave(&port->lock, flags);
@@ -503,7 +503,7 @@
ret = wait_event_interruptible(port->port.delta_msr_wait,
usb_serial_generic_msr_changed(tty, arg, &cnow));
- if (!ret && !test_bit(ASYNCB_INITIALIZED, &port->port.flags))
+ if (!ret && !tty_port_initialized(&port->port))
ret = -EIO;
return ret;
@@ -606,7 +606,7 @@
for (i = 0; i < serial->num_ports; i++) {
port = serial->port[i];
- if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags))
+ if (!tty_port_initialized(&port->port))
continue;
if (port->bulk_in_size) {
diff --git a/drivers/usb/serial/mxuport.c b/drivers/usb/serial/mxuport.c
index 31a8b47..3722d6c 100644
--- a/drivers/usb/serial/mxuport.c
+++ b/drivers/usb/serial/mxuport.c
@@ -503,7 +503,7 @@
return;
}
- if (test_bit(ASYNCB_INITIALIZED, &demux_port->port.flags)) {
+ if (tty_port_initialized(&demux_port->port)) {
ch = data + HEADER_SIZE;
mxuport_process_read_urb_data(demux_port, ch, rcv_len);
} else {
@@ -544,7 +544,7 @@
}
demux_port = serial->port[rcv_port];
- if (test_bit(ASYNCB_INITIALIZED, &demux_port->port.flags)) {
+ if (tty_port_initialized(&demux_port->port)) {
ch = data + HEADER_SIZE;
rcv_event = get_unaligned_be16(data + 2);
mxuport_process_read_urb_event(demux_port, ch,
@@ -1339,7 +1339,7 @@
for (i = 0; i < serial->num_ports; i++) {
port = serial->port[i];
- if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags))
+ if (!tty_port_initialized(&port->port))
continue;
r = usb_serial_generic_write_start(port, GFP_NOIO);
diff --git a/drivers/usb/serial/sierra.c b/drivers/usb/serial/sierra.c
index 07d1ecd..e1994e2 100644
--- a/drivers/usb/serial/sierra.c
+++ b/drivers/usb/serial/sierra.c
@@ -776,7 +776,7 @@
/*
* Need to take susp_lock to make sure port is not already being
- * resumed, but no need to hold it due to ASYNC_INITIALIZED.
+ * resumed, but no need to hold it due to initialized
*/
spin_lock_irq(&intfdata->susp_lock);
if (--intfdata->open_ports == 0)
@@ -1039,7 +1039,7 @@
for (i = 0; i < serial->num_ports; i++) {
port = serial->port[i];
- if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags))
+ if (!tty_port_initialized(&port->port))
continue;
err = sierra_submit_delayed_urbs(port);
diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c
index 46f1f13..3f253ae 100644
--- a/drivers/usb/serial/usb-serial.c
+++ b/drivers/usb/serial/usb-serial.c
@@ -254,7 +254,7 @@
*
* Shut down a USB serial port. Serialized against activate by the
* tport mutex and kept to matching open/close pairs
- * of calls by the ASYNCB_INITIALIZED flag.
+ * of calls by the initialized flag.
*
* Not called if tty is console.
*/
diff --git a/drivers/usb/serial/usb_wwan.c b/drivers/usb/serial/usb_wwan.c
index be9cb61..3dfdfc8 100644
--- a/drivers/usb/serial/usb_wwan.c
+++ b/drivers/usb/serial/usb_wwan.c
@@ -464,7 +464,7 @@
/*
* Need to take susp_lock to make sure port is not already being
- * resumed, but no need to hold it due to ASYNC_INITIALIZED.
+ * resumed, but no need to hold it due to initialized
*/
spin_lock_irq(&intfdata->susp_lock);
if (--intfdata->open_ports == 0)
@@ -682,7 +682,7 @@
for (i = 0; i < serial->num_ports; i++) {
port = serial->port[i];
- if (!test_bit(ASYNCB_INITIALIZED, &port->port.flags))
+ if (!tty_port_initialized(&port->port))
continue;
portdata = usb_get_serial_port_data(port);
diff --git a/drivers/video/console/fbcon.c b/drivers/video/console/fbcon.c
index 6e92917..afd3301 100644
--- a/drivers/video/console/fbcon.c
+++ b/drivers/video/console/fbcon.c
@@ -170,7 +170,7 @@
int height, int width);
static int fbcon_switch(struct vc_data *vc);
static int fbcon_blank(struct vc_data *vc, int blank, int mode_switch);
-static int fbcon_set_palette(struct vc_data *vc, unsigned char *table);
+static int fbcon_set_palette(struct vc_data *vc, const unsigned char *table);
static int fbcon_scrolldelta(struct vc_data *vc, int lines);
/*
@@ -2652,7 +2652,7 @@
0, 16, palette_red, palette_green, palette_blue, NULL
};
-static int fbcon_set_palette(struct vc_data *vc, unsigned char *table)
+static int fbcon_set_palette(struct vc_data *vc, const unsigned char *table)
{
struct fb_info *info = registered_fb[con2fb_map[vc->vc_num]];
int i, j, k, depth;
diff --git a/drivers/video/console/mdacon.c b/drivers/video/console/mdacon.c
index 296e945..8edc062 100644
--- a/drivers/video/console/mdacon.c
+++ b/drivers/video/console/mdacon.c
@@ -481,7 +481,7 @@
return 1; /* redrawing needed */
}
-static int mdacon_set_palette(struct vc_data *c, unsigned char *table)
+static int mdacon_set_palette(struct vc_data *c, const unsigned char *table)
{
return -EINVAL;
}
diff --git a/drivers/video/console/newport_con.c b/drivers/video/console/newport_con.c
index bb4e962..0553dfe 100644
--- a/drivers/video/console/newport_con.c
+++ b/drivers/video/console/newport_con.c
@@ -574,7 +574,7 @@
return newport_set_font(vc->vc_num, font);
}
-static int newport_set_palette(struct vc_data *vc, unsigned char *table)
+static int newport_set_palette(struct vc_data *vc, const unsigned char *table)
{
return -EINVAL;
}
diff --git a/drivers/video/console/sticon.c b/drivers/video/console/sticon.c
index 026fd12..e440c2d 100644
--- a/drivers/video/console/sticon.c
+++ b/drivers/video/console/sticon.c
@@ -79,7 +79,7 @@
return "STI console";
}
-static int sticon_set_palette(struct vc_data *c, unsigned char *table)
+static int sticon_set_palette(struct vc_data *c, const unsigned char *table)
{
return -EINVAL;
}
diff --git a/drivers/video/console/vgacon.c b/drivers/video/console/vgacon.c
index 517f565..8bf9110 100644
--- a/drivers/video/console/vgacon.c
+++ b/drivers/video/console/vgacon.c
@@ -80,7 +80,6 @@
static void vgacon_cursor(struct vc_data *c, int mode);
static int vgacon_switch(struct vc_data *c);
static int vgacon_blank(struct vc_data *c, int blank, int mode_switch);
-static int vgacon_set_palette(struct vc_data *vc, unsigned char *table);
static int vgacon_scrolldelta(struct vc_data *c, int lines);
static int vgacon_set_origin(struct vc_data *c);
static void vgacon_save_screen(struct vc_data *c);
@@ -847,7 +846,7 @@
return 0; /* Redrawing not needed */
}
-static void vga_set_palette(struct vc_data *vc, unsigned char *table)
+static void vga_set_palette(struct vc_data *vc, const unsigned char *table)
{
int i, j;
@@ -860,7 +859,7 @@
}
}
-static int vgacon_set_palette(struct vc_data *vc, unsigned char *table)
+static int vgacon_set_palette(struct vc_data *vc, const unsigned char *table)
{
#ifdef CAN_LOAD_PALETTE
if (vga_video_type != VIDEO_TYPE_VGAC || vga_palette_blanked
diff --git a/include/linux/console.h b/include/linux/console.h
index ea731af..137ac1a 100644
--- a/include/linux/console.h
+++ b/include/linux/console.h
@@ -47,7 +47,7 @@
int (*con_font_copy)(struct vc_data *, int);
int (*con_resize)(struct vc_data *, unsigned int, unsigned int,
unsigned int);
- int (*con_set_palette)(struct vc_data *, unsigned char *);
+ int (*con_set_palette)(struct vc_data *, const unsigned char *);
int (*con_scrolldelta)(struct vc_data *, int);
int (*con_set_origin)(struct vc_data *);
void (*con_save_screen)(struct vc_data *);
diff --git a/include/linux/selection.h b/include/linux/selection.h
index 85193aa..8e4624e 100644
--- a/include/linux/selection.h
+++ b/include/linux/selection.h
@@ -24,10 +24,10 @@
extern int console_blanked;
-extern unsigned char color_table[];
-extern int default_red[];
-extern int default_grn[];
-extern int default_blu[];
+extern const unsigned char color_table[];
+extern unsigned char default_red[];
+extern unsigned char default_grn[];
+extern unsigned char default_blu[];
extern unsigned short *screen_pos(struct vc_data *vc, int w_offset, int viewed);
extern u16 screen_glyph(struct vc_data *vc, int offset);
diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h
index 4348797..48ec765 100644
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -36,6 +36,7 @@
void (*set_termios)(struct uart_port *,
struct ktermios *new,
struct ktermios *old);
+ unsigned int (*get_mctrl)(struct uart_port *);
int (*handle_irq)(struct uart_port *);
void (*pm)(struct uart_port *, unsigned int state,
unsigned old);
@@ -148,6 +149,7 @@
const char *options);
extern void serial8250_do_set_termios(struct uart_port *port,
struct ktermios *termios, struct ktermios *old);
+extern unsigned int serial8250_do_get_mctrl(struct uart_port *port);
extern int serial8250_do_startup(struct uart_port *port);
extern void serial8250_do_shutdown(struct uart_port *port);
extern void serial8250_do_pm(struct uart_port *port, unsigned int state,
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index cbfcf38..a3d7c0d 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -123,6 +123,7 @@
void (*set_termios)(struct uart_port *,
struct ktermios *new,
struct ktermios *old);
+ unsigned int (*get_mctrl)(struct uart_port *);
void (*set_mctrl)(struct uart_port *, unsigned int);
int (*startup)(struct uart_port *port);
void (*shutdown)(struct uart_port *port);
@@ -281,6 +282,8 @@
enum uart_pm_state pm_state;
struct circ_buf xmit;
+ atomic_t refcount;
+ wait_queue_head_t remove_wait;
struct uart_port *uart_port;
};
diff --git a/include/linux/tty.h b/include/linux/tty.h
index 17b247c..40144f3 100644
--- a/include/linux/tty.h
+++ b/include/linux/tty.h
@@ -228,7 +228,8 @@
int count; /* Usage count */
wait_queue_head_t open_wait; /* Open waiters */
wait_queue_head_t delta_msr_wait; /* Modem status change */
- unsigned long flags; /* TTY flags ASY_*/
+ unsigned long flags; /* User TTY flags ASYNC_ */
+ unsigned long iflags; /* Internal flags TTY_PORT_ */
unsigned char console:1, /* port is a console */
low_latency:1; /* optional: tune for latency */
struct mutex mutex; /* Locking */
@@ -242,6 +243,18 @@
struct kref kref; /* Ref counter */
};
+/* tty_port::iflags bits -- use atomic bit ops */
+#define TTY_PORT_INITIALIZED 0 /* device is initialized */
+#define TTY_PORT_SUSPENDED 1 /* device is suspended */
+#define TTY_PORT_ACTIVE 2 /* device is open */
+
+/*
+ * uart drivers: use the uart_port::status field and the UPSTAT_* defines
+ * for s/w-based flow control steering and carrier detection status
+ */
+#define TTY_PORT_CTS_FLOW 3 /* h/w flow control enabled */
+#define TTY_PORT_CHECK_CD 4 /* carrier detect enabled */
+
/*
* Where all of the state associated with a tty is kept while the tty
* is open. Since the termios state should be kept even if the tty
@@ -338,7 +351,6 @@
#define TTY_OTHER_CLOSED 2 /* Other side (if any) has closed */
#define TTY_EXCLUSIVE 3 /* Exclusive open mode */
#define TTY_DO_WRITE_WAKEUP 5 /* Call write_wakeup after queuing new */
-#define TTY_OTHER_DONE 6 /* Closed pty has completed input processing */
#define TTY_LDISC_OPEN 11 /* Line discipline is open */
#define TTY_PTY_LOCK 16 /* pty private */
#define TTY_NO_WRITE_SPLIT 17 /* Preserve write boundaries to driver */
@@ -360,6 +372,16 @@
smp_mb();
}
+static inline bool tty_io_error(struct tty_struct *tty)
+{
+ return test_bit(TTY_IO_ERROR, &tty->flags);
+}
+
+static inline bool tty_throttled(struct tty_struct *tty)
+{
+ return test_bit(TTY_THROTTLED, &tty->flags);
+}
+
#ifdef CONFIG_TTY
extern void console_init(void);
extern void tty_kref_put(struct tty_struct *tty);
@@ -459,6 +481,7 @@
extern void tty_buffer_set_lock_subclass(struct tty_port *port);
extern bool tty_buffer_restart_work(struct tty_port *port);
extern bool tty_buffer_cancel_work(struct tty_port *port);
+extern void tty_buffer_flush_work(struct tty_port *port);
extern speed_t tty_termios_baud_rate(struct ktermios *termios);
extern speed_t tty_termios_input_baud_rate(struct ktermios *termios);
extern void tty_termios_encode_baud_rate(struct ktermios *termios,
@@ -539,7 +562,67 @@
/* If the cts flow control is enabled, return true. */
static inline bool tty_port_cts_enabled(struct tty_port *port)
{
- return port->flags & ASYNC_CTS_FLOW;
+ return test_bit(TTY_PORT_CTS_FLOW, &port->iflags);
+}
+
+static inline void tty_port_set_cts_flow(struct tty_port *port, bool val)
+{
+ if (val)
+ set_bit(TTY_PORT_CTS_FLOW, &port->iflags);
+ else
+ clear_bit(TTY_PORT_CTS_FLOW, &port->iflags);
+}
+
+static inline bool tty_port_active(struct tty_port *port)
+{
+ return test_bit(TTY_PORT_ACTIVE, &port->iflags);
+}
+
+static inline void tty_port_set_active(struct tty_port *port, bool val)
+{
+ if (val)
+ set_bit(TTY_PORT_ACTIVE, &port->iflags);
+ else
+ clear_bit(TTY_PORT_ACTIVE, &port->iflags);
+}
+
+static inline bool tty_port_check_carrier(struct tty_port *port)
+{
+ return test_bit(TTY_PORT_CHECK_CD, &port->iflags);
+}
+
+static inline void tty_port_set_check_carrier(struct tty_port *port, bool val)
+{
+ if (val)
+ set_bit(TTY_PORT_CHECK_CD, &port->iflags);
+ else
+ clear_bit(TTY_PORT_CHECK_CD, &port->iflags);
+}
+
+static inline bool tty_port_suspended(struct tty_port *port)
+{
+ return test_bit(TTY_PORT_SUSPENDED, &port->iflags);
+}
+
+static inline void tty_port_set_suspended(struct tty_port *port, bool val)
+{
+ if (val)
+ set_bit(TTY_PORT_SUSPENDED, &port->iflags);
+ else
+ clear_bit(TTY_PORT_SUSPENDED, &port->iflags);
+}
+
+static inline bool tty_port_initialized(struct tty_port *port)
+{
+ return test_bit(TTY_PORT_INITIALIZED, &port->iflags);
+}
+
+static inline void tty_port_set_initialized(struct tty_port *port, bool val)
+{
+ if (val)
+ set_bit(TTY_PORT_INITIALIZED, &port->iflags);
+ else
+ clear_bit(TTY_PORT_INITIALIZED, &port->iflags);
}
extern struct tty_struct *tty_port_tty_get(struct tty_port *port);
diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
index 24da334..99dbed8 100644
--- a/include/uapi/linux/serial_core.h
+++ b/include/uapi/linux/serial_core.h
@@ -267,4 +267,7 @@
/* Microchip PIC32 UART */
#define PORT_PIC32 115
+/* MPS2 UART */
+#define PORT_MPS2UART 116
+
#endif /* _UAPILINUX_SERIAL_CORE_H */
diff --git a/include/uapi/linux/tty_flags.h b/include/uapi/linux/tty_flags.h
index 072e41e..66e4d8b 100644
--- a/include/uapi/linux/tty_flags.h
+++ b/include/uapi/linux/tty_flags.h
@@ -32,7 +32,13 @@
#define ASYNCB_MAGIC_MULTIPLIER 16 /* Use special CLK or divisor */
#define ASYNCB_LAST_USER 16
-/* Internal flags used only by kernel */
+/*
+ * Internal flags used only by kernel (read-only)
+ *
+ * WARNING: These flags are no longer used and have been superceded by the
+ * TTY_PORT_ flags in the iflags field (and not userspace-visible)
+ */
+#ifndef _KERNEL_
#define ASYNCB_INITIALIZED 31 /* Serial port was initialized */
#define ASYNCB_SUSPENDED 30 /* Serial port is suspended */
#define ASYNCB_NORMAL_ACTIVE 29 /* Normal device is active */
@@ -43,7 +49,9 @@
#define ASYNCB_SHARE_IRQ 24 /* for multifunction cards, no longer used */
#define ASYNCB_CONS_FLOW 23 /* flow control for console */
#define ASYNCB_FIRST_KERNEL 22
+#endif
+/* Masks */
#define ASYNC_HUP_NOTIFY (1U << ASYNCB_HUP_NOTIFY)
#define ASYNC_SUSPENDED (1U << ASYNCB_SUSPENDED)
#define ASYNC_FOURPORT (1U << ASYNCB_FOURPORT)
@@ -72,6 +80,8 @@
#define ASYNC_SPD_WARP (ASYNC_SPD_HI|ASYNC_SPD_SHI)
#define ASYNC_SPD_MASK (ASYNC_SPD_HI|ASYNC_SPD_VHI|ASYNC_SPD_SHI)
+#ifndef _KERNEL_
+/* These flags are no longer used (and were always masked from userspace) */
#define ASYNC_INITIALIZED (1U << ASYNCB_INITIALIZED)
#define ASYNC_NORMAL_ACTIVE (1U << ASYNCB_NORMAL_ACTIVE)
#define ASYNC_BOOT_AUTOCONF (1U << ASYNCB_BOOT_AUTOCONF)
@@ -81,5 +91,6 @@
#define ASYNC_SHARE_IRQ (1U << ASYNCB_SHARE_IRQ)
#define ASYNC_CONS_FLOW (1U << ASYNCB_CONS_FLOW)
#define ASYNC_INTERNAL_FLAGS (~((1U << ASYNCB_FIRST_KERNEL) - 1))
+#endif
#endif
diff --git a/include/uapi/linux/vt.h b/include/uapi/linux/vt.h
index 978578b..f690348 100644
--- a/include/uapi/linux/vt.h
+++ b/include/uapi/linux/vt.h
@@ -8,7 +8,6 @@
*/
#define MIN_NR_CONSOLES 1 /* must be at least 1 */
#define MAX_NR_CONSOLES 63 /* serial lines start at 64 */
-#define MAX_NR_USER_CONSOLES 63 /* must be root to allocate above this */
/* Note: the ioctl VT_GETSTATE does not work for
consoles 16 and higher (since it returns a short) */
diff --git a/net/irda/ircomm/ircomm_tty.c b/net/irda/ircomm/ircomm_tty.c
index da126ee..873c4b7 100644
--- a/net/irda/ircomm/ircomm_tty.c
+++ b/net/irda/ircomm/ircomm_tty.c
@@ -220,10 +220,11 @@
IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return -1;);
/* Check if already open */
- if (test_and_set_bit(ASYNCB_INITIALIZED, &self->port.flags)) {
+ if (tty_port_initialized(&self->port)) {
pr_debug("%s(), already open so break out!\n", __func__);
return 0;
}
+ tty_port_set_initialized(&self->port, 1);
/* Register with IrCOMM */
irda_notify_init(¬ify);
@@ -257,7 +258,7 @@
return 0;
err:
- clear_bit(ASYNCB_INITIALIZED, &self->port.flags);
+ tty_port_set_initialized(&self->port, 0);
return ret;
}
@@ -280,8 +281,8 @@
* If non-blocking mode is set, or the port is not enabled,
* then make the check up front and then exit.
*/
- if (test_bit(TTY_IO_ERROR, &tty->flags)) {
- port->flags |= ASYNC_NORMAL_ACTIVE;
+ if (tty_io_error(tty)) {
+ tty_port_set_active(port, 1);
return 0;
}
@@ -289,7 +290,7 @@
/* nonblock mode is set */
if (C_BAUD(tty))
tty_port_raise_dtr_rts(port);
- port->flags |= ASYNC_NORMAL_ACTIVE;
+ tty_port_set_active(port, 1);
pr_debug("%s(), O_NONBLOCK requested!\n", __func__);
return 0;
}
@@ -318,13 +319,12 @@
spin_unlock_irqrestore(&port->lock, flags);
while (1) {
- if (C_BAUD(tty) && test_bit(ASYNCB_INITIALIZED, &port->flags))
+ if (C_BAUD(tty) && tty_port_initialized(port))
tty_port_raise_dtr_rts(port);
set_current_state(TASK_INTERRUPTIBLE);
- if (tty_hung_up_p(filp) ||
- !test_bit(ASYNCB_INITIALIZED, &port->flags)) {
+ if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
retval = (port->flags & ASYNC_HUP_NOTIFY) ?
-EAGAIN : -ERESTARTSYS;
break;
@@ -365,7 +365,7 @@
__FILE__, __LINE__, tty->driver->name, port->count);
if (!retval)
- port->flags |= ASYNC_NORMAL_ACTIVE;
+ tty_port_set_active(port, 1);
return retval;
}
@@ -876,8 +876,9 @@
IRDA_ASSERT(self != NULL, return;);
IRDA_ASSERT(self->magic == IRCOMM_TTY_MAGIC, return;);
- if (!test_and_clear_bit(ASYNCB_INITIALIZED, &self->port.flags))
+ if (!tty_port_initialized(&self->port))
return;
+ tty_port_set_initialized(&self->port, 0);
ircomm_tty_detach_cable(self);
@@ -925,7 +926,6 @@
ircomm_tty_shutdown(self);
spin_lock_irqsave(&port->lock, flags);
- port->flags &= ~ASYNC_NORMAL_ACTIVE;
if (port->tty) {
set_bit(TTY_IO_ERROR, &port->tty->flags);
tty_kref_put(port->tty);
@@ -933,6 +933,7 @@
port->tty = NULL;
port->count = 0;
spin_unlock_irqrestore(&port->lock, flags);
+ tty_port_set_active(port, 0);
wake_up_interruptible(&port->open_wait);
}
@@ -999,7 +1000,7 @@
if (status & IRCOMM_DCE_DELTA_ANY) {
/*wake_up_interruptible(&self->delta_msr_wait);*/
}
- if ((self->port.flags & ASYNC_CHECK_CD) && (status & IRCOMM_DELTA_CD)) {
+ if (tty_port_check_carrier(&self->port) && (status & IRCOMM_DELTA_CD)) {
pr_debug("%s(), ircomm%d CD now %s...\n", __func__ , self->line,
(status & IRCOMM_CD) ? "on" : "off");
@@ -1255,11 +1256,11 @@
seq_printf(m, "%cASYNC_CTS_FLOW", sep);
sep = '|';
}
- if (self->port.flags & ASYNC_CHECK_CD) {
+ if (tty_port_check_carrier(&self->port)) {
seq_printf(m, "%cASYNC_CHECK_CD", sep);
sep = '|';
}
- if (self->port.flags & ASYNC_INITIALIZED) {
+ if (tty_port_initialized(&self->port)) {
seq_printf(m, "%cASYNC_INITIALIZED", sep);
sep = '|';
}
@@ -1267,7 +1268,7 @@
seq_printf(m, "%cASYNC_LOW_LATENCY", sep);
sep = '|';
}
- if (self->port.flags & ASYNC_NORMAL_ACTIVE) {
+ if (tty_port_active(&self->port)) {
seq_printf(m, "%cASYNC_NORMAL_ACTIVE", sep);
sep = '|';
}
diff --git a/net/irda/ircomm/ircomm_tty_attach.c b/net/irda/ircomm/ircomm_tty_attach.c
index 61137f8..0a41101 100644
--- a/net/irda/ircomm/ircomm_tty_attach.c
+++ b/net/irda/ircomm/ircomm_tty_attach.c
@@ -968,7 +968,7 @@
ircomm_tty_next_state(self, IRCOMM_TTY_SEARCH);
ircomm_tty_start_watchdog_timer(self, 3*HZ);
- if (self->port.flags & ASYNC_CHECK_CD) {
+ if (tty_port_check_carrier(&self->port)) {
/* Drop carrier */
self->settings.dce = IRCOMM_DELTA_CD;
ircomm_tty_check_modem_status(self);
diff --git a/net/irda/ircomm/ircomm_tty_ioctl.c b/net/irda/ircomm/ircomm_tty_ioctl.c
index d3687aa..d4fdf8f 100644
--- a/net/irda/ircomm/ircomm_tty_ioctl.c
+++ b/net/irda/ircomm/ircomm_tty_ioctl.c
@@ -86,21 +86,17 @@
ircomm_param_request(self, IRCOMM_DATA_RATE, FALSE);
/* CTS flow control flag and modem status interrupts */
+ tty_port_set_cts_flow(&self->port, cflag & CRTSCTS);
if (cflag & CRTSCTS) {
- self->port.flags |= ASYNC_CTS_FLOW;
self->settings.flow_control |= IRCOMM_RTS_CTS_IN;
/* This got me. Bummer. Jean II */
if (self->service_type == IRCOMM_3_WIRE_RAW)
net_warn_ratelimited("%s(), enabling RTS/CTS on link that doesn't support it (3-wire-raw)\n",
__func__);
} else {
- self->port.flags &= ~ASYNC_CTS_FLOW;
self->settings.flow_control &= ~IRCOMM_RTS_CTS_IN;
}
- if (cflag & CLOCAL)
- self->port.flags &= ~ASYNC_CHECK_CD;
- else
- self->port.flags |= ASYNC_CHECK_CD;
+ tty_port_set_check_carrier(&self->port, ~cflag & CLOCAL);
#if 0
/*
* Set up parity check flag
@@ -166,7 +162,7 @@
/* Handle transition away from B0 status */
if (!(old_termios->c_cflag & CBAUD) && (cflag & CBAUD)) {
self->settings.dte |= IRCOMM_DTR;
- if (!C_CRTSCTS(tty) || !test_bit(TTY_THROTTLED, &tty->flags))
+ if (!C_CRTSCTS(tty) || !tty_throttled(tty))
self->settings.dte |= IRCOMM_RTS;
ircomm_param_request(self, IRCOMM_DTE, TRUE);
}
@@ -190,7 +186,7 @@
struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) tty->driver_data;
unsigned int result;
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
result = ((self->settings.dte & IRCOMM_RTS) ? TIOCM_RTS : 0)
@@ -213,7 +209,7 @@
{
struct ircomm_tty_cb *self = (struct ircomm_tty_cb *) tty->driver_data;
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
IRDA_ASSERT(self != NULL, return -1;);
@@ -328,7 +324,7 @@
check_and_exit:
- if (self->flags & ASYNC_INITIALIZED) {
+ if (tty_port_initialized(self)) {
if (((old_state.flags & ASYNC_SPD_MASK) !=
(self->flags & ASYNC_SPD_MASK)) ||
(old_driver.custom_divisor != driver->custom_divisor)) {
@@ -362,7 +358,7 @@
if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
(cmd != TIOCSERCONFIG) && (cmd != TIOCSERGSTRUCT) &&
(cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) {
- if (tty->flags & (1 << TTY_IO_ERROR))
+ if (tty_io_error(tty))
return -EIO;
}