blob: be06d668a3c93ab25d0407df68eb849467e6b3dd [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * linux/arch/arm/mach-sa1100/assabet.c
3 *
4 * Author: Nicolas Pitre
5 *
6 * This file contains all Assabet-specific tweaks.
7 *
8 * This program is free software; you can redistribute it and/or modify
9 * it under the terms of the GNU General Public License version 2 as
10 * published by the Free Software Foundation.
11 */
Linus Torvalds1da177e2005-04-16 15:20:36 -070012#include <linux/init.h>
13#include <linux/kernel.h>
14#include <linux/module.h>
15#include <linux/errno.h>
16#include <linux/ioport.h>
17#include <linux/serial_core.h>
18#include <linux/mtd/mtd.h>
19#include <linux/mtd/partitions.h>
20#include <linux/delay.h>
21#include <linux/mm.h>
22
23#include <asm/hardware.h>
24#include <asm/mach-types.h>
25#include <asm/irq.h>
26#include <asm/setup.h>
27#include <asm/page.h>
Russell King74945c82006-03-16 14:44:36 +000028#include <asm/pgtable-hwdef.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070029#include <asm/pgtable.h>
30#include <asm/tlbflush.h>
31
32#include <asm/mach/arch.h>
33#include <asm/mach/flash.h>
34#include <asm/mach/irda.h>
35#include <asm/mach/map.h>
36#include <asm/mach/serial_sa1100.h>
37#include <asm/arch/assabet.h>
Russell King323cdfc2005-08-18 10:10:46 +010038#include <asm/arch/mcp.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070039
40#include "generic.h"
41
42#define ASSABET_BCR_DB1110 \
43 (ASSABET_BCR_SPK_OFF | ASSABET_BCR_QMUTE | \
44 ASSABET_BCR_LED_GREEN | ASSABET_BCR_LED_RED | \
45 ASSABET_BCR_RS232EN | ASSABET_BCR_LCD_12RGB | \
46 ASSABET_BCR_IRDA_MD0)
47
48#define ASSABET_BCR_DB1111 \
49 (ASSABET_BCR_SPK_OFF | ASSABET_BCR_QMUTE | \
50 ASSABET_BCR_LED_GREEN | ASSABET_BCR_LED_RED | \
51 ASSABET_BCR_RS232EN | ASSABET_BCR_LCD_12RGB | \
52 ASSABET_BCR_CF_BUS_OFF | ASSABET_BCR_STEREO_LB | \
53 ASSABET_BCR_IRDA_MD0 | ASSABET_BCR_CF_RST)
54
55unsigned long SCR_value = ASSABET_SCR_INIT;
56EXPORT_SYMBOL(SCR_value);
57
58static unsigned long BCR_value = ASSABET_BCR_DB1110;
59
60void ASSABET_BCR_frob(unsigned int mask, unsigned int val)
61{
62 unsigned long flags;
63
64 local_irq_save(flags);
65 BCR_value = (BCR_value & ~mask) | val;
66 ASSABET_BCR = BCR_value;
67 local_irq_restore(flags);
68}
69
70EXPORT_SYMBOL(ASSABET_BCR_frob);
71
72static void assabet_backlight_power(int on)
73{
74#ifndef ASSABET_PAL_VIDEO
75 if (on)
76 ASSABET_BCR_set(ASSABET_BCR_LIGHT_ON);
77 else
78#endif
79 ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON);
80}
81
82/*
83 * Turn on/off the backlight. When turning the backlight on,
84 * we wait 500us after turning it on so we don't cause the
85 * supplies to droop when we enable the LCD controller (and
86 * cause a hard reset.)
87 */
88static void assabet_lcd_power(int on)
89{
90#ifndef ASSABET_PAL_VIDEO
91 if (on) {
92 ASSABET_BCR_set(ASSABET_BCR_LCD_ON);
93 udelay(500);
94 } else
95#endif
96 ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
97}
98
99
100/*
101 * Assabet flash support code.
102 */
103
104#ifdef ASSABET_REV_4
105/*
106 * Phase 4 Assabet has two 28F160B3 flash parts in bank 0:
107 */
108static struct mtd_partition assabet_partitions[] = {
109 {
110 .name = "bootloader",
111 .size = 0x00020000,
112 .offset = 0,
113 .mask_flags = MTD_WRITEABLE,
114 }, {
115 .name = "bootloader params",
116 .size = 0x00020000,
117 .offset = MTDPART_OFS_APPEND,
118 .mask_flags = MTD_WRITEABLE,
119 }, {
120 .name = "jffs",
121 .size = MTDPART_SIZ_FULL,
122 .offset = MTDPART_OFS_APPEND,
123 }
124};
125#else
126/*
127 * Phase 5 Assabet has two 28F128J3A flash parts in bank 0:
128 */
129static struct mtd_partition assabet_partitions[] = {
130 {
131 .name = "bootloader",
132 .size = 0x00040000,
133 .offset = 0,
134 .mask_flags = MTD_WRITEABLE,
135 }, {
136 .name = "bootloader params",
137 .size = 0x00040000,
138 .offset = MTDPART_OFS_APPEND,
139 .mask_flags = MTD_WRITEABLE,
140 }, {
141 .name = "jffs",
142 .size = MTDPART_SIZ_FULL,
143 .offset = MTDPART_OFS_APPEND,
144 }
145};
146#endif
147
148static struct flash_platform_data assabet_flash_data = {
149 .map_name = "cfi_probe",
150 .parts = assabet_partitions,
151 .nr_parts = ARRAY_SIZE(assabet_partitions),
152};
153
154static struct resource assabet_flash_resources[] = {
155 {
156 .start = SA1100_CS0_PHYS,
157 .end = SA1100_CS0_PHYS + SZ_32M - 1,
158 .flags = IORESOURCE_MEM,
159 }, {
160 .start = SA1100_CS1_PHYS,
161 .end = SA1100_CS1_PHYS + SZ_32M - 1,
162 .flags = IORESOURCE_MEM,
163 }
164};
165
166
167/*
168 * Assabet IrDA support code.
169 */
170
171static int assabet_irda_set_power(struct device *dev, unsigned int state)
172{
173 static unsigned int bcr_state[4] = {
174 ASSABET_BCR_IRDA_MD0,
175 ASSABET_BCR_IRDA_MD1|ASSABET_BCR_IRDA_MD0,
176 ASSABET_BCR_IRDA_MD1,
177 0
178 };
179
180 if (state < 4) {
181 state = bcr_state[state];
182 ASSABET_BCR_clear(state ^ (ASSABET_BCR_IRDA_MD1|
183 ASSABET_BCR_IRDA_MD0));
184 ASSABET_BCR_set(state);
185 }
186 return 0;
187}
188
189static void assabet_irda_set_speed(struct device *dev, unsigned int speed)
190{
191 if (speed < 4000000)
192 ASSABET_BCR_clear(ASSABET_BCR_IRDA_FSEL);
193 else
194 ASSABET_BCR_set(ASSABET_BCR_IRDA_FSEL);
195}
196
197static struct irda_platform_data assabet_irda_data = {
198 .set_power = assabet_irda_set_power,
199 .set_speed = assabet_irda_set_speed,
200};
201
Russell King323cdfc2005-08-18 10:10:46 +0100202static struct mcp_plat_data assabet_mcp_data = {
203 .mccr0 = MCCR0_ADM,
204 .sclk_rate = 11981000,
205};
206
Linus Torvalds1da177e2005-04-16 15:20:36 -0700207static void __init assabet_init(void)
208{
209 /*
210 * Ensure that the power supply is in "high power" mode.
211 */
212 GPDR |= GPIO_GPIO16;
213 GPSR = GPIO_GPIO16;
214
215 /*
216 * Ensure that these pins are set as outputs and are driving
217 * logic 0. This ensures that we won't inadvertently toggle
218 * the WS latch in the CPLD, and we don't float causing
219 * excessive power drain. --rmk
220 */
221 GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
222 GPCR = GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
223
224 /*
225 * Set up registers for sleep mode.
226 */
227 PWER = PWER_GPIO0;
228 PGSR = 0;
229 PCFR = 0;
230 PSDR = 0;
231 PPDR |= PPC_TXD3 | PPC_TXD1;
232 PPSR |= PPC_TXD3 | PPC_TXD1;
233
234 sa1100fb_lcd_power = assabet_lcd_power;
235 sa1100fb_backlight_power = assabet_backlight_power;
236
237 if (machine_has_neponset()) {
238 /*
239 * Angel sets this, but other bootloaders may not.
240 *
241 * This must precede any driver calls to BCR_set()
242 * or BCR_clear().
243 */
244 ASSABET_BCR = BCR_value = ASSABET_BCR_DB1111;
245
246#ifndef CONFIG_ASSABET_NEPONSET
247 printk( "Warning: Neponset detected but full support "
248 "hasn't been configured in the kernel\n" );
249#endif
250 }
251
252 sa11x0_set_flash_data(&assabet_flash_data, assabet_flash_resources,
253 ARRAY_SIZE(assabet_flash_resources));
254 sa11x0_set_irda_data(&assabet_irda_data);
Russell King323cdfc2005-08-18 10:10:46 +0100255 sa11x0_set_mcp_data(&assabet_mcp_data);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700256}
257
258/*
259 * On Assabet, we must probe for the Neponset board _before_
260 * paging_init() has occurred to actually determine the amount
261 * of RAM available. To do so, we map the appropriate IO section
262 * in the page table here in order to access GPIO registers.
263 */
264static void __init map_sa1100_gpio_regs( void )
265{
266 unsigned long phys = __PREG(GPLR) & PMD_MASK;
267 unsigned long virt = io_p2v(phys);
268 int prot = PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_DOMAIN(DOMAIN_IO);
269 pmd_t *pmd;
270
271 pmd = pmd_offset(pgd_offset_k(virt), virt);
272 *pmd = __pmd(phys | prot);
273 flush_pmd_entry(pmd);
274}
275
276/*
277 * Read System Configuration "Register"
278 * (taken from "Intel StrongARM SA-1110 Microprocessor Development Board
279 * User's Guide", section 4.4.1)
280 *
281 * This same scan is performed in arch/arm/boot/compressed/head-sa1100.S
282 * to set up the serial port for decompression status messages. We
283 * repeat it here because the kernel may not be loaded as a zImage, and
284 * also because it's a hassle to communicate the SCR value to the kernel
285 * from the decompressor.
286 *
287 * Note that IRQs are guaranteed to be disabled.
288 */
289static void __init get_assabet_scr(void)
290{
291 unsigned long scr, i;
292
293 GPDR |= 0x3fc; /* Configure GPIO 9:2 as outputs */
294 GPSR = 0x3fc; /* Write 0xFF to GPIO 9:2 */
295 GPDR &= ~(0x3fc); /* Configure GPIO 9:2 as inputs */
Russell King2f3eca82005-11-21 17:01:13 +0000296 for(i = 100; i--; ) /* Read GPIO 9:2 */
297 scr = GPLR;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700298 GPDR |= 0x3fc; /* restore correct pin direction */
299 scr &= 0x3fc; /* save as system configuration byte. */
300 SCR_value = scr;
301}
302
303static void __init
304fixup_assabet(struct machine_desc *desc, struct tag *tags,
305 char **cmdline, struct meminfo *mi)
306{
307 /* This must be done before any call to machine_has_neponset() */
308 map_sa1100_gpio_regs();
309 get_assabet_scr();
310
311 if (machine_has_neponset())
312 printk("Neponset expansion board detected\n");
313}
314
315
316static void assabet_uart_pm(struct uart_port *port, u_int state, u_int oldstate)
317{
318 if (port->mapbase == _Ser1UTCR0) {
319 if (state)
320 ASSABET_BCR_clear(ASSABET_BCR_RS232EN |
321 ASSABET_BCR_COM_RTS |
322 ASSABET_BCR_COM_DTR);
323 else
324 ASSABET_BCR_set(ASSABET_BCR_RS232EN |
325 ASSABET_BCR_COM_RTS |
326 ASSABET_BCR_COM_DTR);
327 }
328}
329
330/*
331 * Assabet uses COM_RTS and COM_DTR for both UART1 (com port)
332 * and UART3 (radio module). We only handle them for UART1 here.
333 */
334static void assabet_set_mctrl(struct uart_port *port, u_int mctrl)
335{
336 if (port->mapbase == _Ser1UTCR0) {
337 u_int set = 0, clear = 0;
338
339 if (mctrl & TIOCM_RTS)
340 clear |= ASSABET_BCR_COM_RTS;
341 else
342 set |= ASSABET_BCR_COM_RTS;
343
344 if (mctrl & TIOCM_DTR)
345 clear |= ASSABET_BCR_COM_DTR;
346 else
347 set |= ASSABET_BCR_COM_DTR;
348
349 ASSABET_BCR_clear(clear);
350 ASSABET_BCR_set(set);
351 }
352}
353
354static u_int assabet_get_mctrl(struct uart_port *port)
355{
356 u_int ret = 0;
357 u_int bsr = ASSABET_BSR;
358
359 /* need 2 reads to read current value */
360 bsr = ASSABET_BSR;
361
362 if (port->mapbase == _Ser1UTCR0) {
363 if (bsr & ASSABET_BSR_COM_DCD)
364 ret |= TIOCM_CD;
365 if (bsr & ASSABET_BSR_COM_CTS)
366 ret |= TIOCM_CTS;
367 if (bsr & ASSABET_BSR_COM_DSR)
368 ret |= TIOCM_DSR;
369 } else if (port->mapbase == _Ser3UTCR0) {
370 if (bsr & ASSABET_BSR_RAD_DCD)
371 ret |= TIOCM_CD;
372 if (bsr & ASSABET_BSR_RAD_CTS)
373 ret |= TIOCM_CTS;
374 if (bsr & ASSABET_BSR_RAD_DSR)
375 ret |= TIOCM_DSR;
376 if (bsr & ASSABET_BSR_RAD_RI)
377 ret |= TIOCM_RI;
378 } else {
379 ret = TIOCM_CD | TIOCM_CTS | TIOCM_DSR;
380 }
381
382 return ret;
383}
384
385static struct sa1100_port_fns assabet_port_fns __initdata = {
386 .set_mctrl = assabet_set_mctrl,
387 .get_mctrl = assabet_get_mctrl,
388 .pm = assabet_uart_pm,
389};
390
391static struct map_desc assabet_io_desc[] __initdata = {
Deepak Saxena92519d82005-10-28 15:19:04 +0100392 { /* Board Control Register */
393 .virtual = 0xf1000000,
394 .pfn = __phys_to_pfn(0x12000000),
395 .length = 0x00100000,
396 .type = MT_DEVICE
397 }, { /* MQ200 */
398 .virtual = 0xf2800000,
399 .pfn = __phys_to_pfn(0x4b800000),
400 .length = 0x00800000,
401 .type = MT_DEVICE
402 }
Linus Torvalds1da177e2005-04-16 15:20:36 -0700403};
404
405static void __init assabet_map_io(void)
406{
407 sa1100_map_io();
408 iotable_init(assabet_io_desc, ARRAY_SIZE(assabet_io_desc));
409
410 /*
411 * Set SUS bit in SDCR0 so serial port 1 functions.
412 * Its called GPCLKR0 in my SA1110 manual.
413 */
414 Ser1SDCR0 |= SDCR0_SUS;
415
416 if (machine_has_neponset()) {
417#ifdef CONFIG_ASSABET_NEPONSET
418 extern void neponset_map_io(void);
419
420 /*
421 * We map Neponset registers even if it isn't present since
422 * many drivers will try to probe their stuff (and fail).
423 * This is still more friendly than a kernel paging request
424 * crash.
425 */
426 neponset_map_io();
427#endif
428 } else {
429 sa1100_register_uart_fns(&assabet_port_fns);
430 }
431
432 /*
433 * When Neponset is attached, the first UART should be
434 * UART3. That's what Angel is doing and many documents
435 * are stating this.
436 *
437 * We do the Neponset mapping even if Neponset support
438 * isn't compiled in so the user will still get something on
439 * the expected physical serial port.
440 *
441 * We no longer do this; not all boot loaders support it,
442 * and UART3 appears to be somewhat unreliable with blob.
443 */
444 sa1100_register_uart(0, 1);
445 sa1100_register_uart(2, 3);
446}
447
448
449MACHINE_START(ASSABET, "Intel-Assabet")
Russell Kinge9dea0c2005-07-03 17:38:58 +0100450 .phys_io = 0x80000000,
451 .io_pg_offst = ((0xf8000000) >> 18) & 0xfffc,
452 .boot_params = 0xc0000100,
453 .fixup = fixup_assabet,
454 .map_io = assabet_map_io,
455 .init_irq = sa1100_init_irq,
Linus Torvalds1da177e2005-04-16 15:20:36 -0700456 .timer = &sa1100_timer,
457 .init_machine = assabet_init,
458MACHINE_END