Documentation/devicetree/bindings/display/msm/sde.txt

Qualcomm Technologies, Inc. SDE KMS

Snapdragon Display Engine implements Linux DRM/KMS APIs to drive user
interface to different panel interfaces. SDE driver is the core of
display subsystem which manage all data paths to different panel interfaces.

Required properties
- compatible: Must be "qcom,sde-kms"
- compatible: "msm-hdmi-audio-codec-rx";
- reg: Offset and length of the register set for the device.
- reg-names : Names to refer to register sets related to this device
- clocks: List of Phandles for clock device nodes
    needed by the device.
- clock-names: List of clock names needed by the device.
- mmagic-supply: Phandle for mmagic mdss supply regulator device node.
- vdd-supply: Phandle for vdd regulator device node.
- interrupt-parent: Must be core interrupt controller.
- interrupts: Interrupt associated with MDSS.
- interrupt-controller: Mark the device node as an interrupt controller.
- #interrupt-cells: Should be one. The first cell is interrupt number.
- iommus: Specifies the SID's used by this context bank.
- qcom,sde-sspp-type:		Array of strings for SDE source surface pipes type information.
				A source pipe can be "vig", "rgb", "dma" or "cursor" type.
				Number of xin ids defined should match the number of offsets
				defined in property: qcom,sde-sspp-off.
- qcom,sde-sspp-off:		Array of offset for SDE source surface pipes. The offsets
				are calculated from register "mdp_phys" defined in
				reg property + "sde-off". The number of offsets defined here should
				reflect the amount of pipes that can be active in SDE for
				this configuration.
- qcom,sde-sspp-xin-id:		Array of VBIF clients ids (xins) corresponding
				to the respective source pipes. Number of xin ids
				defined should match the number of offsets
				defined in property: qcom,sde-sspp-off.
- qcom,sde-ctl-off:		Array of offset addresses for the available ctl
				hw blocks within SDE, these offsets are
				calculated from register "mdp_phys" defined in
				reg property.  The number of ctl offsets defined
				here should reflect the number of control paths
				that can be configured concurrently on SDE for
				this configuration.
- qcom,sde-wb-off:		Array of offset addresses for the programmable
				writeback blocks within SDE.
- qcom,sde-wb-xin-id:		Array of VBIF clients ids (xins) corresponding
				to the respective writeback. Number of xin ids
				defined should match the number of offsets
				defined in property: qcom,sde-wb-off.
- qcom,sde-mixer-off:	 	Array of offset addresses for the available
				mixer blocks that can drive data to panel
				interfaces. These offsets are be calculated from
				register "mdp_phys" defined in reg property.
				The number of offsets defined should reflect the
				amount of mixers that can drive data to a panel
				interface.
- qcom,sde-dspp-top-off:		Offset address for the dspp top block.
				The offset is calculated from register "mdp_phys"
				defined in reg property.
- qcom,sde-dspp-off: 		Array of offset addresses for the available dspp
				blocks. These offsets are calculated from
				register "mdp_phys" defined in reg property.
- qcom,sde-pp-off:		Array of offset addresses for the available
				pingpong blocks. These offsets are calculated
				from register "mdp_phys" defined in reg property.
- qcom,sde-pp-slave:		Array of flags indicating whether each ping pong
				block may be configured as a pp slave.
- qcom,sde-intf-off:		Array of offset addresses for the available SDE
				interface blocks that can drive data to a
				panel controller. The offsets are calculated
				from "mdp_phys" defined in reg property. The number
				of offsets defined should reflect the number of
				programmable interface blocks available in hardware.
- qcom,sde-mixer-blend-op-off	Array of offset addresses for the available
				blending stages. The offsets are relative to
				qcom,sde-mixer-off.
- qcom,sde-mixer-pair-mask	Array of mixer numbers that can be paired with
				mixer number corresponding to the array index.

Optional properties:
- clock-rate:		List of clock rates in Hz.
- clock-max-rate:	List of maximum clock rate in Hz that this device supports.
- connectors:		Specifies the connector components.
- bridges:		Specifies the bridge components.
- qcom,platform-supply-entries:	A node that lists the elements of the supply. There
				can be more than one instance of this binding,
				in which case the entry would be appended with
				the supply entry index.
				e.g. qcom,platform-supply-entry@0
				-- reg: offset and length of the register set for the device.
				-- qcom,supply-name: name of the supply (vdd/vdda/vddio)
				-- qcom,supply-min-voltage: minimum voltage level (uV)
				-- qcom,supply-max-voltage: maximum voltage level (uV)
				-- qcom,supply-enable-load: load drawn (uA) from enabled supply
				-- qcom,supply-disable-load: load drawn (uA) from disabled supply
				-- qcom,supply-pre-on-sleep: time to sleep (ms) before turning on
				-- qcom,supply-post-on-sleep: time to sleep (ms) after turning on
				-- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off
				-- qcom,supply-post-off-sleep: time to sleep (ms) after turning off
- qcom,sde-sspp-src-size:	A u32 value indicates the address range for each sspp.
- qcom,sde-mixer-size:		A u32 value indicates the address range for each mixer.
- qcom,sde-ctl-size:		A u32 value indicates the address range for each ctl.
- qcom,sde-dspp-size:		A u32 value indicates the address range for each dspp.
- qcom,sde-intf-size:		A u32 value indicates the address range for each intf.
- qcom,sde-dsc-size:		A u32 value indicates the address range for each dsc.
- qcom,sde-cdm-size:		A u32 value indicates the address range for each cdm.
- qcom,sde-pp-size:		A u32 value indicates the address range for each pingpong.
- qcom,sde-wb-size:		A u32 value indicates the address range for each writeback.
- qcom,sde-len:			A u32 entry for SDE address range.
- qcom,sde-intf-max-prefetch-lines:	Array of u32 values for max prefetch lines on
				each interface.
- qcom,sde-sspp-linewidth:	A u32 value indicates the max sspp line width.
- qcom,sde-mixer-linewidth:	A u32 value indicates the max mixer line width.
- qcom,sde-wb-linewidth:	A u32 value indicates the max writeback line width.
- qcom,sde-sspp-scale-size:	A u32 value indicates the scaling block size on sspp.
- qcom,sde-mixer-blendstages:	A u32 value indicates the max mixer blend stages for
				alpha blending.
- qcom,sde-qseed-type:		A string entry indiates qseed support on sspp and wb.
				It supports "qssedv3" and "qseedv2" entries for qseed
				type. By default "qseedv2" is used if this optional property
				is not defined.
- qcom,sde-csc-type:		A string entry indicates csc support on sspp and wb.
				It supports "csc" and "csc-10bit" entries for csc
				type.
- qcom,sde-highest-bank-bit:	A u32 property to indicate GPU/Camera/Video highest memory
				bank bit used for tile format buffers.
- qcom,sde-ubwc-version:	Property to specify the UBWC feature version.
- qcom,sde-ubwc-static:	Property to specify the default UBWC static
				configuration value.
- qcom,sde-ubwc-swizzle:	Property to specify the default UBWC swizzle
				configuration value.
- qcom,sde-smart-panel-align-mode: A u32 property to specify the align mode for
				split display on smart panel. Possible values:
				0x0 - no alignment
				0xc - align at start of frame
				0xd - align at start of line
- qcom,sde-panic-per-pipe:	Boolean property to indicate if panic signal
				control feature is available on each source pipe.
- qcom,sde-has-src-split:	Boolean property to indicate if source split
				feature is available or not.
- qcom,sde-has-dim-layer:	Boolean property to indicate if mixer has dim layer
				feature is available or not.
- qcom,sde-has-idle-pc:		Boolean property to indicate if target has idle
				power collapse feature available or not.
- qcom,sde-has-mixer-gc:	Boolean property to indicate if mixer has gamma correction
				feature available or not.
- qcom,sde-has-dest-scaler: 	Boolean property to indicate if destination scaler
				feature is available or not.
- qcom,sde-max-dest-scaler-input-linewidth: A u32 value indicates the
				maximum input line width to destination scaler.
- qcom,sde-max-dest-scaler-output-linewidth: A u32 value indicates the
				maximum output line width of destination scaler.
- qcom,sde-dest-scaler-top-off: A u32 value provides the
				offset from mdp base to destination scaler block.
- qcom,sde-dest-scaler-top-size: A u32 value indicates the address range for ds top
- qcom,sde-dest-scaler-off: 	Array of u32 offsets indicate the qseed3 scaler blocks
				offset from destination scaler top offset.
- qcom,sde-dest-scaler-size:    A u32 value indicates the address range for each scaler block
- qcom,sde-sspp-clk-ctrl:	Array of offsets describing clk control
				offsets for dynamic clock gating. 1st value
				in the array represents offset of the control
				register. 2nd value represents bit offset within
				control register. Number of offsets defined should
				match the number of offsets defined in
				property: qcom,sde-sspp-off
- qcom,sde-sspp-clk-status:	Array of offsets describing clk status
				offsets for dynamic clock gating. 1st value
				in the array represents offset of the status
				register. 2nd value represents bit offset within
				control register. Number of offsets defined should
				match the number of offsets defined in
				property: qcom,sde-sspp-off.
- qcom,sde-sspp-excl-rect:	Array of u32 values indicating exclusion rectangle
				support on each sspp.
- qcom,sde-sspp-smart-dma-priority:	Array of u32 values indicating hw pipe
					priority of secondary rectangles when smart dma
					is supported. Number of priority values should
					match the number of offsets defined in
					qcom,sde-sspp-off node. Zero indicates no support
					for smart dma for the sspp.
- qcom,sde-smart-dma-rev:	A string entry indicating the smart dma version
				supported on the device. Supported entries are
				"smart_dma_v1" and "smart_dma_v2".
- qcom,sde-intf-type:		Array of string provides the interface type information.
				Possible string values
					"dsi" - dsi display interface
					"dp" - Display Port interface
					"hdmi" - HDMI display interface
				An interface is considered as "none" if interface type
				is not defined.
- qcom,sde-off:			SDE offset from "mdp_phys" defined in reg property.
- qcom,sde-cdm-off:	 	Array of offset addresses for the available
				cdm blocks. These offsets will be calculated from
				register "mdp_phys" defined in reg property.
- qcom,sde-vbif-off:		Array of offset addresses for the available
				vbif blocks. These offsets will be calculated from
				register "vbif_phys" defined in reg property.
- qcom,sde-vbif-size:		A u32 value indicates the vbif block address range.
- qcom,sde-te-off:		A u32 offset indicates the te block offset on pingpong.
				This offset is 0x0 by default.
- qcom,sde-te2-off:		A u32 offset indicates the te2 block offset on pingpong.
- qcom,sde-te-size:		A u32 value indicates the te block address range.
- qcom,sde-te2-size:		A u32 value indicates the te2 block address range.
- qcom,sde-dsc-off:	 	A u32 offset indicates the dsc block offset on pingpong.
- qcom,sde-dither-off:		A u32 offset indicates the dither block offset on pingpong.
- qcom,sde-dither-version:	A u32 value indicates the dither block version.
- qcom,sde-dither-size:		A u32 value indicates the dither block address range.
- qcom,sde-sspp-vig-blocks:	A node that lists the blocks inside the VIG hardware. The
				block entries will contain the offset and version (if needed)
				of each feature block. The presence of a block entry
				indicates that the SSPP VIG contains that feature hardware.
				e.g. qcom,sde-sspp-vig-blocks
				-- qcom,sde-vig-csc-off: offset of CSC hardware
				-- qcom,sde-vig-qseed-off: offset of QSEED hardware
				-- qcom,sde-vig-qseed-size: A u32 address range for qseed scaler.
				-- qcom,sde-vig-pcc: offset and version of PCC hardware
				-- qcom,sde-vig-hsic: offset and version of global PA adjustment
				-- qcom,sde-vig-memcolor: offset and version of PA memcolor hardware
- qcom,sde-sspp-rgb-blocks:	A node that lists the blocks inside the RGB hardware. The
				block entries will contain the offset and version (if needed)
				of each feature block. The presence of a block entry
				indicates that the SSPP RGB contains that feature hardware.
				e.g. qcom,sde-sspp-vig-blocks
				-- qcom,sde-rgb-scaler-off: offset of RGB scaler hardware
				-- qcom,sde-rgb-scaler-size: A u32 address range for scaler.
				-- qcom,sde-rgb-pcc: offset and version of PCC hardware
- qcom,sde-dspp-blocks:		A node that lists the blocks inside the DSPP hardware. The
				block entries will contain the offset and version of each
				feature block. The presence of a block entry indicates that
				the DSPP contains that feature hardware.
				e.g. qcom,sde-dspp-blocks
				-- qcom,sde-dspp-pcc: offset and version of PCC hardware
				-- qcom,sde-dspp-gc: offset and version of GC hardware
				-- qcom,sde-dspp-igc: offset and version of IGC hardware
				-- qcom,sde-dspp-hsic: offset and version of global PA adjustment
				-- qcom,sde-dspp-memcolor: offset and version of PA memcolor hardware
				-- qcom,sde-dspp-sixzone: offset and version of PA sixzone hardware
				-- qcom,sde-dspp-gamut: offset and version of Gamut mapping hardware
				-- qcom,sde-dspp-dither: offset and version of dither hardware
				-- qcom,sde-dspp-hist: offset and version of histogram hardware
				-- qcom,sde-dspp-vlut: offset and version of PA vLUT hardware
- qcom,sde-mixer-blocks:	A node that lists the blocks inside the layer mixer hardware. The
				block entries will contain the offset and version (if needed)
				of each feature block. The presence of a block entry
				indicates that the layer mixer contains that feature hardware.
				e.g. qcom,sde-mixer-blocks
				-- qcom,sde-mixer-gc: offset and version of mixer GC hardware
- qcom,sde-dspp-ad-off:		Array of u32 offsets indicate the ad block offset from the
				DSPP offset. Since AD hardware is represented as part of
				DSPP block, the AD offsets must be offset from the
				corresponding DSPP base.
- qcom,sde-dspp-ad-version	A u32 value indicating the version of the AD hardware
- qcom,sde-vbif-id:		Array of vbif ids corresponding to the
				offsets defined in property: qcom,sde-vbif-off.
- qcom,sde-vbif-default-ot-rd-limit:	A u32 value indicates the default read OT limit
- qcom,sde-vbif-default-ot-wr-limit:	A u32 value indicates the default write OT limit
- qcom,sde-vbif-dynamic-ot-rd-limit:	A series of 2 cell property, with a format
				of (pps, OT limit), where pps is pixel per second and
				OT limit is the read limit to apply if the given
				pps is not exceeded.
- qcom,sde-vbif-dynamic-ot-wr-limit:	A series of 2 cell property, with a format
				of (pps, OT limit), where pps is pixel per second and
				OT limit is the write limit to apply if the given
				pps is not exceeded.
- qcom,sde-vbif-memtype-0:	Array of u32 vbif memory type settings, group 0
- qcom,sde-vbif-memtype-1:	Array of u32 vbif memory type settings, group 1
- qcom,sde-wb-id:		Array of writeback ids corresponding to the
				offsets defined in property: qcom,sde-wb-off.
- qcom,sde-wb-clk-ctrl:		Array of 2 cell property describing clk control
				offsets for dynamic clock gating. 1st value
				in the array represents offset of the control
				register. 2nd value represents bit offset within
				control register. Number of offsets defined should
				match the number of offsets defined in
				property: qcom,sde-wb-off
- qcom,sde-reg-dma-off:         Offset of the register dma hardware block from
				"regdma_phys" defined in reg property.
- qcom,sde-reg-dma-version:	Version of the reg dma hardware block.
- qcom,sde-reg-dma-trigger-off: Offset of the lut dma trigger reg from "mdp_phys"
				defined in reg property.
- qcom,sde-dram-channels:	This represents the number of channels in the
				Bus memory controller.
- qcom,sde-num-nrt-paths:	Integer property represents the number of non-realtime
				paths in each Bus Scaling Usecase. This value depends on
				number of AXI ports that are dedicated to non-realtime VBIF
				for particular chipset.
				These paths must be defined after rt-paths in
				"qcom,msm-bus,vectors-KBps" vector request.
- qcom,sde-max-bw-low-kbps:	This value indicates the max bandwidth in Kbps
				that can be supported without underflow.
				This is a low bandwidth threshold which should
				be applied in most scenarios to be safe from
				underflows when unable to satisfy bandwidth
				requirements.
- qcom,sde-max-bw-high-kbps:	This value indicates the max bandwidth in Kbps
				that can be supported without underflow.
				This is a high bandwidth threshold which can be
				applied in scenarios where panel interface can
				be more tolerant to memory latency such as
				command mode panels.
- qcom,sde-core-ib-ff:		A string entry indicating the fudge factor for
				core ib calculation.
- qcom,sde-core-clk-ff:		A string entry indicating the fudge factor for
				core clock calculation.
- qcom,sde-min-core-ib-kbps:	This u32 value indicates the minimum mnoc ib
				vote in Kbps that can be reduced without hitting underflow.
				BW calculation logic will choose the IB bandwidth requirement
				based on usecase if this floor value is not defined.
- qcom,sde-min-llcc-ib-kbps:	This u32 value indicates the minimum llcc ib
				vote in Kbps that can be reduced without hitting underflow.
				BW calculation logic will choose the IB bandwidth requirement
				based on usecase if this floor value is not defined.
- qcom,sde-min-dram-ib-kbps:	This u32 value indicates the minimum dram ib
				vote in Kbps that can be reduced without hitting underflow.
				BW calculation logic will choose the IB bandwidth requirement
				based on usecase if this floor value is not defined.
- qcom,sde-comp-ratio-rt:	A string entry indicating the compression ratio
				for each supported compressed format on realtime interface.
				The string is composed of one or more of
				<fourcc code>/<vendor code>/<modifier>/<compression ratio>
				separated with spaces.
- qcom,sde-comp-ratio-nrt:	A string entry indicating the compression ratio
				for each supported compressed format on non-realtime interface.
				The string is composed of one or more of
				<fourcc code>/<vendor code>/<modifier>/<compression ratio>
				separated with spaces.
- qcom,sde-undersized-prefill-lines:	A u32 value indicates the size of undersized prefill in lines.
- qcom,sde-xtra-prefill-lines:	A u32 value indicates the extra prefill in lines.
- qcom,sde-dest-scale-prefill-lines:	A u32 value indicates the latency of destination scaler in lines.
- qcom,sde-macrotile-prefill-lines:	A u32 value indicates the latency of macrotile in lines.
- qcom,sde-yuv-nv12-prefill-lines:	A u32 value indicates the latency of yuv/nv12 in lines.
- qcom,sde-linear-prefill-lines:	A u32 value indicates the latency of linear in lines.
- qcom,sde-downscaling-prefill-lines:	A u32 value indicates the latency of downscaling in lines.
- qcom,sde-max-per-pipe-bw-kbps:	Array of u32 value indicates the max per pipe bandwidth in Kbps.
- qcom,sde-amortizable-threshold:	This value indicates the min for traffic shaping in lines.
- qcom,sde-vbif-qos-rt-remap:	This array is used to program vbif qos remapper register
				priority for realtime clients.
- qcom,sde-vbif-qos-nrt-remap:	This array is used to program vbif qos remapper register
				priority for non-realtime clients.
- qcom,sde-danger-lut:		A 4 cell property, with a format of <linear,
				tile, nrt, cwb>,
				indicating the danger luts on sspp.
- qcom,sde-safe-lut-linear:	Array of 2 cell property, with a format of
				<fill level, lut> in ascending fill level
				indicating the safe luts for linear format on sspp.
				Zero fill level on the last entry identifies the default lut.
- qcom,sde-safe-lut-macrotile:	Array of 2 cell property, with a format of
				<fill level, lut> in ascending fill level
				indicating the safe luts for macrotile format on sspp.
				Zero fill level on the last entry identifies the default lut.
- qcom,sde-safe-lut-nrt:	Array of 2 cell property, with a format of
				<fill level, lut> in ascending fill level
				indicating the safe luts for nrt (e.g wfd) on sspp.
				Zero fill level on the last entry identifies the default lut.
- qcom,sde-safe-lut-cwb:	Array of 2 cell property, with a format of
				<fill level, lut> in ascending fill level
				indicating the safe luts for cwb on sspp.
				Zero fill level on the last entry identifies the default lut.
- qcom,sde-qos-lut-linear:	Array of 3 cell property, with a format of
				<fill level, lut hi, lut lo> in ascending fill level
				indicating the qos luts for linear format on sspp.
				Zero fill level on the last entry identifies the default lut.
- qcom,sde-qos-lut-macrotile:	Array of 3 cell property, with a format of
				<fill level, lut hi, lut lo> in ascending fill level
				indicating the qos luts for macrotile format on sspp.
				Zero fill level on the last entry identifies the default lut.
- qcom,sde-qos-lut-nrt:		Array of 3 cell property, with a format of
				<fill level, lut hi, lut lo> in ascending fill level
				indicating the qos luts for nrt (e.g wfd) on sspp.
				Zero fill level on the last entry identifies the default lut.
- qcom,sde-qos-lut-cwb:		Array of 3 cell property, with a format of
				<fill level, lut hi, lut lo> in ascending fill level
				indicating the qos luts for cwb on sspp.
				Zero fill level on the last entry identifies the default lut.
- qcom,sde-cdp-setting:		Array of 2 cell property, with a format of
				<read enable, write enable> for cdp use cases in
				order of <real_time>, and <non_real_time>.
- qcom,sde-qos-cpu-mask:	A u32 value indicating desired PM QoS CPU affine mask.
- qcom,sde-qos-cpu-dma-latency:	A u32 value indicating desired PM QoS CPU DMA latency in usec.
- qcom,sde-inline-rot-xin:	An integer array of xin-ids related to inline
				rotation.
- qcom,sde-inline-rot-xin-type:	A string array indicating the type of xin,
				namely sspp or wb. Number of entries should match
				the number of xin-ids defined in
				property: qcom,sde-inline-rot-xin
- qcom,sde-inline-rot-clk-ctrl:	Array of offsets describing clk control
				offsets for dynamic clock gating. 1st value
				in the array represents offset of the control
				register. 2nd value represents bit offset within
				control register. Number of offsets defined should
				match the number of xin-ids defined in
				property: qcom,sde-inline-rot-xin
- #power-domain-cells:		Number of cells in a power-domain specifier and should contain 0.
- qcom,sde-mixer-display-pref:  A string array indicating the preferred display type
				for the mixer block. Possible values:
				"primary" - preferred for primary display
				"none" - no preference on display
- qcom,sde-ctl-display-pref:    A string array indicating the preferred display type
                                for the ctl block. Possible values:
				"primary" - preferred for primary display
				"none" - no preference on display

Bus Scaling Subnodes:
- qcom,sde-reg-bus:		Property to provide Bus scaling for register access for
				mdss blocks.
- qcom,sde-data-bus:		Property to provide Bus scaling for data bus access for
				mdss blocks.
- qcom,sde-llcc-bus:		Property to provide Bus scaling for data bus access for
				mnoc to llcc.
- qcom,sde-ebi-bus:		Property to provide Bus scaling for data bus access for
				llcc to ebi.

- qcom,sde-inline-rotator:	A 2 cell property, with format of (rotator phandle,
				instance id), of inline rotator device.

Bus Scaling Data:
- qcom,msm-bus,name:		String property describing client name.
- qcom,msm-bus,num-cases:	This is the number of Bus Scaling use cases
				defined in the vectors property.
- qcom,msm-bus,num-paths:	This represents the number of paths in each
				Bus Scaling Usecase.
- qcom,msm-bus,vectors-KBps:	* A series of 4 cell properties, with a format
				of (src, dst, ab, ib) which is defined at
				Documentation/devicetree/bindings/arm/msm/msm_bus.txt
				* Current values of src & dst are defined at
				include/linux/msm-bus-board.h

SMMU Subnodes:
- smmu_sde_****:		Child nodes representing sde smmu virtual
				devices

Subnode properties:
- compatible:			Compatible names used for smmu devices.
				names should be:
				"qcom,smmu_sde_unsec": smmu context bank device
				for unsecure sde real time domain.
				"qcom,smmu_sde_sec": smmu context bank device
				for secure sde real time domain.
				"qcom,smmu_sde_nrt_unsec": smmu context bank device
				for unsecure sde non-real time domain.
				"qcom,smmu_sde_nrt_sec": smmu context bank device
				for secure sde non-real time domain.


Please refer to ../../interrupt-controller/interrupts.txt for a general
description of interrupt bindings.

Example:
  mdss_mdp: qcom,mdss_mdp@900000 {
    compatible = "qcom,sde-kms";
    reg = <0x00900000 0x90000>,
          <0x009b0000 0x1040>,
          <0x009b8000 0x1040>,
          <0x0aeac000 0x00f0>;
    reg-names = "mdp_phys",
      "vbif_phys",
      "vbif_nrt_phys",
      "regdma_phys";
    clocks = <&clock_mmss clk_mdss_ahb_clk>,
      <&clock_mmss clk_mdss_axi_clk>,
      <&clock_mmss clk_mdp_clk_src>,
      <&clock_mmss clk_mdss_mdp_vote_clk>,
      <&clock_mmss clk_smmu_mdp_axi_clk>,
      <&clock_mmss clk_mmagic_mdss_axi_clk>,
      <&clock_mmss clk_mdss_vsync_clk>;
    clock-names = "iface_clk",
      "bus_clk",
      "core_clk_src",
      "core_clk",
      "iommu_clk",
      "mmagic_clk",
      "vsync_clk";
    clock-rate = <0>, <0>, <0>;
    clock-max-rate= <0 320000000 0>;
    mmagic-supply = <&gdsc_mmagic_mdss>;
    vdd-supply = <&gdsc_mdss>;
    interrupt-parent = <&intc>;
    interrupts = <0 83 0>;
    interrupt-controller;
    #interrupt-cells = <1>;
    iommus = <&mdp_smmu 0>;
    #power-domain-cells = <0>;

    qcom,sde-off = <0x1000>;
    qcom,sde-ctl-off = <0x00002000 0x00002200 0x00002400
		     0x00002600 0x00002800>;
    qcom,sde-ctl-display-pref = "primary", "none", "none",
	             "none", "none";
    qcom,sde-mixer-off = <0x00045000 0x00046000
			0x00047000 0x0004a000>;
    qcom,sde-mixer-display-pref = "primary", "none",
	                "none", "none";
    qcom,sde-dspp-top-off = <0x1300>;
    qcom,sde-dspp-off = <0x00055000 0x00057000>;
    qcom,sde-dspp-ad-off = <0x24000 0x22800>;
    qcom,sde-dspp-ad-version = <0x00030000>;
    qcom,sde-dest-scaler-top-off = <0x00061000>;
    qcom,sde-dest-scaler-off = <0x800 0x1000>;
    qcom,sde-wb-off = <0x00066000>;
    qcom,sde-wb-xin-id = <6>;
    qcom,sde-intf-off = <0x0006b000 0x0006b800
			0x0006c000 0x0006c800>;
    qcom,sde-intf-type = "none", "dsi", "dsi", "hdmi";
    qcom,sde-pp-off = <0x00071000 0x00071800
			  0x00072000 0x00072800>;
    qcom,sde-pp-slave = <0x0 0x0 0x0 0x0>;
    qcom,sde-cdm-off = <0x0007a200>;
    qcom,sde-dsc-off = <0x00081000 0x00081400>;
    qcom,sde-intf-max-prefetch-lines = <0x15 0x15 0x15 0x15>;

    qcom,sde-mixer-pair-mask = <2 1 6 0 0 3>;
    qcom,sde-mixer-blend-op-off = <0x20 0x38 0x50 0x68 0x80 0x98
				    0xb0 0xc8 0xe0 0xf8 0x110>;


    qcom,sde-sspp-type = "vig", "vig", "vig",
			      "vig", "rgb", "rgb",
			      "rgb", "rgb", "dma",
			      "dma", "cursor", "cursor";

    qcom,sde-sspp-off = <0x00005000 0x00007000 0x00009000
		      0x0000b000 0x00015000 0x00017000
		      0x00019000 0x0001b000 0x00025000
		      0x00027000 0x00035000 0x00037000>;

    qcom,sde-sspp-xin-id = <0 4 8
			12 1 5
			9 13 2
			10 7 7>;

    /* offsets are relative to "mdp_phys + qcom,sde-off */
    qcom,sde-sspp-clk-ctrl = <0x2ac 0>, <0x2b4 0>, <0x2bc 0>,
			  <0x2c4 0>, <0x2ac 4>, <0x2b4 4>, <0x2bc 4>,
			  <0x2c4 4>, <0x2ac 8>, <0x2b4 8>, <0x3a8 16>,
			  <0x3b0 16>;
    qcom,sde-sspp-clk-status = <0x2ac 0>, <0x2b4 0>, <0x2bc 0>,
			  <0x2c4 0>, <0x2ac 4>, <0x2b4 4>, <0x2bc 4>,
			  <0x2c4 4>, <0x2ac 8>, <0x2b4 8>, <0x3a8 16>,
			  <0x3b0 16>;
    qcom,sde-mixer-linewidth = <2560>;
    qcom,sde-sspp-linewidth = <2560>;
    qcom,sde-mixer-blendstages = <0x7>;
    qcom,sde-highest-bank-bit = <0x2>;
    qcom,sde-ubwc-version = <0x100>;
    qcom,sde-ubwc-static = <0x100>;
    qcom,sde-ubwc-swizzle = <0>;
    qcom,sde-smart-panel-align-mode = <0xd>;
    qcom,sde-panic-per-pipe;
    qcom,sde-has-src-split;
    qcom,sde-has-dim-layer;
    qcom,sde-sspp-src-size = <0x100>;
    qcom,sde-mixer-size = <0x100>;
    qcom,sde-ctl-size = <0x100>;
    qcom,sde-dspp-top-size = <0xc>;
    qcom,sde-dspp-size = <0x100>;
    qcom,sde-intf-size = <0x100>;
    qcom,sde-dsc-size = <0x100>;
    qcom,sde-cdm-size = <0x100>;
    qcom,sde-pp-size = <0x100>;
    qcom,sde-wb-size = <0x100>;
    qcom,sde-dest-scaler-top-size = <0xc>;
    qcom,sde-dest-scaler-size = <0x800>;
    qcom,sde-len = <0x100>;
    qcom,sde-wb-linewidth = <2560>;
    qcom,sde-sspp-scale-size = <0x100>;
    qcom,sde-mixer-blendstages = <0x8>;
    qcom,sde-qseed-type = "qseedv2";
    qcom,sde-csc-type = "csc-10bit";
    qcom,sde-highest-bank-bit = <15>;
    qcom,sde-has-mixer-gc;
    qcom,sde-has-idle-pc;
    qcom,sde-has-dest-scaler;
    qcom,sde-max-dest-scaler-input-linewidth = <2048>;
    qcom,sde-max-dest-scaler-output-linewidth = <2560>;
    qcom,sde-sspp-max-rects = <1 1 1 1
				1 1 1 1
				1 1
				1 1>;
    qcom,sde-sspp-excl-rect = <1 1 1 1
				1 1 1 1
				1 1
				1 1>;
    qcom,sde-sspp-smart-dma-priority = <0 0 0 0
					0 0 0 0
					0 0
					1 2>;
    qcom,sde-smart-dma-rev = "smart_dma_v2";
    qcom,sde-te-off = <0x100>;
    qcom,sde-te2-off = <0x100>;
    qcom,sde-te-size = <0xffff>;
    qcom,sde-te2-size = <0xffff>;

    qcom,sde-wb-id = <2>;
    qcom,sde-wb-clk-ctrl = <0x2bc 16>;

    qcom,sde-danger-lut = <0x0000000f 0x0000ffff 0x00000000
            0x00000000>;
    qcom,sde-safe-lut = <0xfffc 0xff00 0xffff 0xffff>;
    qcom,sde-qos-lut-linear =
            <4 0x00000000 0x00000357>,
            <5 0x00000000 0x00003357>,
            <6 0x00000000 0x00023357>,
            <7 0x00000000 0x00223357>,
            <8 0x00000000 0x02223357>,
            <9 0x00000000 0x22223357>,
            <10 0x00000002 0x22223357>,
            <11 0x00000022 0x22223357>,
            <12 0x00000222 0x22223357>,
            <13 0x00002222 0x22223357>,
            <14 0x00012222 0x22223357>,
            <0 0x00112222 0x22223357>;
    qcom,sde-qos-lut-macrotile =
            <10 0x00000003 0x44556677>,
            <11 0x00000033 0x44556677>,
            <12 0x00000233 0x44556677>,
            <13 0x00002233 0x44556677>,
            <14 0x00012233 0x44556677>,
            <0 0x00112233 0x44556677>;
    qcom,sde-qos-lut-nrt =
            <0 0x00000000 0x00000000>;
    qcom,sde-qos-lut-cwb =
            <0 0x75300000 0x00000000>;

    qcom,sde-cdp-setting = <1 1>, <1 0>;

    qcom,sde-qos-cpu-mask = <0x3>;
    qcom,sde-qos-cpu-dma-latency = <300>;

    qcom,sde-vbif-off = <0 0>;
    qcom,sde-vbif-id = <0 1>;
    qcom,sde-vbif-default-ot-rd-limit = <32>;
    qcom,sde-vbif-default-ot-wr-limit = <16>;
    qcom,sde-vbif-dynamic-ot-rd-limit = <62208000 2>,
        <124416000 4>, <248832000 16>;
    qcom,sde-vbif-dynamic-ot-wr-limit = <62208000 2>,
        <124416000 4>, <248832000 16>;
    qcom,sde-vbif-memtype-0 = <3 3 3 3 3 3 3 3>;
    qcom,sde-vbif-memtype-1 = <3 3 3 3 3 3>;

    qcom,sde-dram-channels = <2>;
    qcom,sde-num-nrt-paths = <1>;

    qcom,sde-max-bw-high-kbps = <9000000>;
    qcom,sde-max-bw-low-kbps = <9000000>;

    qcom,sde-core-ib-ff = "1.1";
    qcom,sde-core-clk-ff = "1.0";
    qcom,sde-min-core-ib-kbps = <2400000>;
    qcom,sde-min-llcc-ib-kbps = <800000>;
    qcom,sde-min-dram-ib-kbps = <800000>;
    qcom,sde-comp-ratio-rt = "NV12/5/1/1.1 AB24/5/1/1.2 XB24/5/1/1.3";
    qcom,sde-comp-ratio-nrt = "NV12/5/1/1.1 AB24/5/1/1.2 XB24/5/1/1.3";
    qcom,sde-undersized-prefill-lines = <4>;
    qcom,sde-xtra-prefill-lines = <5>;
    qcom,sde-dest-scale-prefill-lines = <6>;
    qcom,sde-macrotile-prefill-lines = <7>;
    qcom,sde-yuv-nv12-prefill-lines = <8>;
    qcom,sde-linear-prefill-lines = <9>;
    qcom,sde-downscaling-prefill-lines = <10>;
    qcom,sde-max-per-pipe-bw-kbps = <2400000 2400000 2400000 2400000
        2400000 2400000 2400000 2400000>;
    qcom,sde-amortizable-threshold = <11>;

    qcom,sde-vbif-qos-rt-remap = <3 3 4 4 5 5 6 6>;
    qcom,sde-vbif-qos-nrt-remap = <3 3 3 3 3 3 3 3>;

    qcom,sde-sspp-vig-blocks {
        qcom,sde-vig-csc-off = <0x320>;
        qcom,sde-vig-qseed-off = <0x200>;
        qcom,sde-vig-qseed-size = <0x74>;
        /* Offset from vig top, version of HSIC */
        qcom,sde-vig-hsic = <0x200 0x00010000>;
        qcom,sde-vig-memcolor = <0x200 0x00010000>;
        qcom,sde-vig-pcc = <0x1780 0x00010000>;
    };

    qcom,sde-sspp-rgb-blocks {
        qcom,sde-rgb-scaler-off = <0x200>;
        qcom,sde-rgb-scaler-size = <0x74>;
        qcom,sde-rgb-pcc = <0x380 0x00010000>;
    };

    qcom,sde-dspp-blocks {
        qcom,sde-dspp-igc = <0x0 0x00010000>;
        qcom,sde-dspp-pcc = <0x1700 0x00010000>;
        qcom,sde-dspp-gc = <0x17c0 0x00010000>;
        qcom,sde-dspp-hsic = <0x0 0x00010000>;
        qcom,sde-dspp-memcolor = <0x0 0x00010000>;
        qcom,sde-dspp-sixzone = <0x0 0x00010000>;
        qcom,sde-dspp-gamut = <0x1600 0x00010000>;
        qcom,sde-dspp-dither = <0x0 0x00010000>;
        qcom,sde-dspp-hist = <0x0 0x00010000>;
        qcom,sde-dspp-vlut = <0x0 0x00010000>;
    };

    qcom,sde-mixer-blocks {
        qcom,sde-mixer-gc = <0x3c0 0x00010000>;
    };

    qcom,msm-hdmi-audio-rx {
        compatible = "qcom,msm-hdmi-audio-codec-rx";
    };

    qcom,sde-inline-rotator = <&mdss_rotator 0>;
    qcom,sde-inline-rot-xin = <10 11>;
    qcom,sde-inline-rot-xin-type = "sspp", "wb";
    qcom,sde-inline-rot-clk-ctrl = <0x2bc 0x8>, <0x2bc 0xc>;

    qcom,platform-supply-entries {
       #address-cells = <1>;
       #size-cells = <0>;
       qcom,platform-supply-entry@0 {
           reg = <0>;
           qcom,supply-name = "vdd";
           qcom,supply-min-voltage = <0>;
           qcom,supply-max-voltage = <0>;
           qcom,supply-enable-load = <0>;
           qcom,supply-disable-load = <0>;
           qcom,supply-pre-on-sleep = <0>;
           qcom,supply-post-on-sleep = <0>;
           qcom,supply-pre-off-sleep = <0>;
           qcom,supply-post-off-sleep = <0>;
        };
    };

    qcom,sde-data-bus {
        qcom,msm-bus,name = "mdss_sde";
        qcom,msm-bus,num-cases = <3>;
        qcom,msm-bus,num-paths = <3>;
        qcom,msm-bus,vectors-KBps =
            <22 512 0 0>, <23 512 0 0>, <25 512 0 0>,
            <22 512 0 6400000>, <23 512 0 6400000>,
                <25 512 0 6400000>,
            <22 512 0 6400000>, <23 512 0 6400000>,
                <25 512 0 6400000>;
    };
    qcom,sde-llcc-bus {
        qcom,msm-bus,name = "mdss_sde_llcc";
        qcom,msm-bus,num-cases = <3>;
        qcom,msm-bus,num-paths = <1>;
        qcom,msm-bus,vectors-KBps =
            <132 770 0 0>,
            <132 770 0 6400000>,
            <132 770 0 6400000>;
    };
    qcom,sde-ebi-bus {
        qcom,msm-bus,name = "mdss_sde_ebi";
        qcom,msm-bus,num-cases = <3>;
        qcom,msm-bus,num-paths = <1>;
        qcom,msm-bus,vectors-KBps =
            <129 512 0 0>,
            <129 512 0 6400000>,
            <129 512 0 6400000>;
    };

    qcom,sde-reg-bus {
        /* Reg Bus Scale Settings */
        qcom,msm-bus,name = "mdss_reg";
        qcom,msm-bus,num-cases = <4>;
        qcom,msm-bus,num-paths = <1>;
        qcom,msm-bus,active-only;
        qcom,msm-bus,vectors-KBps =
              <1 590 0 0>,
              <1 590 0 76800>,
              <1 590 0 160000>,
              <1 590 0 320000>;
        };

    smmu_kms_unsec: qcom,smmu_kms_unsec_cb {
        compatible = "qcom,smmu_sde_unsec";
        iommus = <&mmss_smmu 0>;
    };

    smmu_kms_sec: qcom,smmu_kms_sec_cb {
        compatible = "qcom,smmu_sde_sec";
        iommus = <&mmss_smmu 1>;
    };
  };