arch/x86/include/asm/pgtable-3level.h

#ifndef _ASM_X86_PGTABLE_3LEVEL_H
#define _ASM_X86_PGTABLE_3LEVEL_H

/*
 * Intel Physical Address Extension (PAE) Mode - three-level page
 * tables on PPro+ CPUs.
 *
 * Copyright (C) 1999 Ingo Molnar <mingo@redhat.com>
 */

#define pte_ERROR(e)							\
	printk("%s:%d: bad pte %p(%08lx%08lx).\n",			\
	       __FILE__, __LINE__, &(e), (e).pte_high, (e).pte_low)
#define pmd_ERROR(e)							\
	printk("%s:%d: bad pmd %p(%016Lx).\n",				\
	       __FILE__, __LINE__, &(e), pmd_val(e))
#define pgd_ERROR(e)							\
	printk("%s:%d: bad pgd %p(%016Lx).\n",				\
	       __FILE__, __LINE__, &(e), pgd_val(e))

/* Rules for using set_pte: the pte being assigned *must* be
 * either not present or in a state where the hardware will
 * not attempt to update the pte.  In places where this is
 * not possible, use pte_get_and_clear to obtain the old pte
 * value and then use set_pte to update it.  -ben
 */
static inline void native_set_pte(pte_t *ptep, pte_t pte)
{
	ptep->pte_high = pte.pte_high;
	smp_wmb();
	ptep->pte_low = pte.pte_low;
}

static inline void native_set_pte_atomic(pte_t *ptep, pte_t pte)
{
	set_64bit((unsigned long long *)(ptep), native_pte_val(pte));
}

static inline void native_set_pmd(pmd_t *pmdp, pmd_t pmd)
{
	set_64bit((unsigned long long *)(pmdp), native_pmd_val(pmd));
}

static inline void native_set_pud(pud_t *pudp, pud_t pud)
{
	set_64bit((unsigned long long *)(pudp), native_pud_val(pud));
}

/*
 * For PTEs and PDEs, we must clear the P-bit first when clearing a page table
 * entry, so clear the bottom half first and enforce ordering with a compiler
 * barrier.
 */
static inline void native_pte_clear(struct mm_struct *mm, unsigned long addr,
				    pte_t *ptep)
{
	ptep->pte_low = 0;
	smp_wmb();
	ptep->pte_high = 0;
}

static inline void native_pmd_clear(pmd_t *pmd)
{
	u32 *tmp = (u32 *)pmd;
	*tmp = 0;
	smp_wmb();
	*(tmp + 1) = 0;
}

static inline void pud_clear(pud_t *pudp)
{
	unsigned long pgd;

	set_pud(pudp, __pud(0));

	/*
	 * According to Intel App note "TLBs, Paging-Structure Caches,
	 * and Their Invalidation", April 2007, document 317080-001,
	 * section 8.1: in PAE mode we explicitly have to flush the
	 * TLB via cr3 if the top-level pgd is changed...
	 *
	 * Make sure the pud entry we're updating is within the
	 * current pgd to avoid unnecessary TLB flushes.
	 */
	pgd = read_cr3();
	if (__pa(pudp) >= pgd && __pa(pudp) <
	    (pgd + sizeof(pgd_t)*PTRS_PER_PGD))
		write_cr3(pgd);
}

#ifdef CONFIG_SMP
static inline pte_t native_ptep_get_and_clear(pte_t *ptep)
{
	pte_t res;

	/* xchg acts as a barrier before the setting of the high bits */
	res.pte_low = xchg(&ptep->pte_low, 0);
	res.pte_high = ptep->pte_high;
	ptep->pte_high = 0;

	return res;
}
#else
#define native_ptep_get_and_clear(xp) native_local_ptep_get_and_clear(xp)
#endif

/*
 * Bits 0, 6 and 7 are taken in the low part of the pte,
 * put the 32 bits of offset into the high part.
 */
#define pte_to_pgoff(pte) ((pte).pte_high)
#define pgoff_to_pte(off)						\
	((pte_t) { { .pte_low = _PAGE_FILE, .pte_high = (off) } })
#define PTE_FILE_MAX_BITS       32

/* Encode and de-code a swap entry */
#define MAX_SWAPFILES_CHECK() BUILD_BUG_ON(MAX_SWAPFILES_SHIFT > 5)
#define __swp_type(x)			(((x).val) & 0x1f)
#define __swp_offset(x)			((x).val >> 5)
#define __swp_entry(type, offset)	((swp_entry_t){(type) | (offset) << 5})
#define __pte_to_swp_entry(pte)		((swp_entry_t){ (pte).pte_high })
#define __swp_entry_to_pte(x)		((pte_t){ { .pte_high = (x).val } })

#endif /* _ASM_X86_PGTABLE_3LEVEL_H */