arch/m68knommu/platform/5307/config.c

/***************************************************************************/

/*
 *	linux/arch/m68knommu/platform/5307/config.c
 *
 *	Copyright (C) 1999-2002, Greg Ungerer (gerg@snapgear.com)
 *	Copyright (C) 2000, Lineo (www.lineo.com)
 */

/***************************************************************************/

#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/param.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <asm/irq.h>
#include <asm/dma.h>
#include <asm/traps.h>
#include <asm/machdep.h>
#include <asm/coldfire.h>
#include <asm/mcftimer.h>
#include <asm/mcfsim.h>
#include <asm/mcfdma.h>
#include <asm/mcfwdebug.h>

/***************************************************************************/

void coldfire_tick(void);
void coldfire_timer_init(irqreturn_t (*handler)(int, void *, struct pt_regs *));
unsigned long coldfire_timer_offset(void);
void coldfire_trap_init(void);
void coldfire_reset(void);

extern unsigned int mcf_timervector;
extern unsigned int mcf_profilevector;
extern unsigned int mcf_timerlevel;

/***************************************************************************/

/*
 *	Some platforms need software versions of the GPIO data registers.
 */
unsigned short ppdata;
unsigned char ledbank = 0xff;

/***************************************************************************/

/*
 *	DMA channel base address table.
 */
unsigned int   dma_base_addr[MAX_M68K_DMA_CHANNELS] = {
        MCF_MBAR + MCFDMA_BASE0,
        MCF_MBAR + MCFDMA_BASE1,
        MCF_MBAR + MCFDMA_BASE2,
        MCF_MBAR + MCFDMA_BASE3,
};

unsigned int dma_device_address[MAX_M68K_DMA_CHANNELS];

/***************************************************************************/

void mcf_autovector(unsigned int vec)
{
	volatile unsigned char  *mbar;

	if ((vec >= 25) && (vec <= 31)) {
		mbar = (volatile unsigned char *) MCF_MBAR;
		vec = 0x1 << (vec - 24);
		*(mbar + MCFSIM_AVR) |= vec;
		mcf_setimr(mcf_getimr() & ~vec);
	}
}

/***************************************************************************/

void mcf_settimericr(unsigned int timer, unsigned int level)
{
	volatile unsigned char *icrp;
	unsigned int icr, imr;

	if (timer <= 2) {
		switch (timer) {
		case 2:  icr = MCFSIM_TIMER2ICR; imr = MCFSIM_IMR_TIMER2; break;
		default: icr = MCFSIM_TIMER1ICR; imr = MCFSIM_IMR_TIMER1; break;
		}

		icrp = (volatile unsigned char *) (MCF_MBAR + icr);
		*icrp = MCFSIM_ICR_AUTOVEC | (level << 2) | MCFSIM_ICR_PRI3;
		mcf_setimr(mcf_getimr() & ~imr);
	}
}

/***************************************************************************/

int mcf_timerirqpending(int timer)
{
	unsigned int imr = 0;

	switch (timer) {
	case 1:  imr = MCFSIM_IMR_TIMER1; break;
	case 2:  imr = MCFSIM_IMR_TIMER2; break;
	default: break;
	}
	return (mcf_getipr() & imr);
}

/***************************************************************************/

void config_BSP(char *commandp, int size)
{
	mcf_setimr(MCFSIM_IMR_MASKALL);

#if defined(CONFIG_BOOTPARAM)
	strncpy(commandp, CONFIG_BOOTPARAM_STRING, size);
	commandp[size-1] = 0;
#elif defined(CONFIG_NETtel) || defined(CONFIG_eLIA) || \
      defined(CONFIG_DISKtel) || defined(CONFIG_SECUREEDGEMP3) || \
      defined(CONFIG_CLEOPATRA)
	/* Copy command line from FLASH to local buffer... */
	memcpy(commandp, (char *) 0xf0004000, size);
	commandp[size-1] = 0;
	/* Different timer setup - to prevent device clash */
	mcf_timervector = 30;
	mcf_profilevector = 31;
	mcf_timerlevel = 6;
#else
	memset(commandp, 0, size);
#endif

	mach_sched_init = coldfire_timer_init;
	mach_tick = coldfire_tick;
	mach_gettimeoffset = coldfire_timer_offset;
	mach_trap_init = coldfire_trap_init;
	mach_reset = coldfire_reset;

#ifdef MCF_BDM_DISABLE
	/*
	 * Disable the BDM clocking.  This also turns off most of the rest of
	 * the BDM device.  This is good for EMC reasons. This option is not
	 * incompatible with the memory protection option.
	 */
	wdebug(MCFDEBUG_CSR, MCFDEBUG_CSR_PSTCLK);
#endif
}

/***************************************************************************/