drivers/scsi/t128.c

#define PSEUDO_DMA

/*
 * Trantor T128/T128F/T228 driver
 *	Note : architecturally, the T100 and T130 are different and won't 
 * 	work
 *
 * Copyright 1993, Drew Eckhardt
 *	Visionary Computing
 *	(Unix and Linux consulting and custom programming)
 *	drew@colorado.edu
 *      +1 (303) 440-4894
 *
 * For more information, please consult 
 *
 * Trantor Systems, Ltd.
 * T128/T128F/T228 SCSI Host Adapter
 * Hardware Specifications
 * 
 * Trantor Systems, Ltd. 
 * 5415 Randall Place
 * Fremont, CA 94538
 * 1+ (415) 770-1400, FAX 1+ (415) 770-9910
 */

/*
 * The card is detected and initialized in one of several ways : 
 * 1.  Autoprobe (default) - since the board is memory mapped, 
 *     a BIOS signature is scanned for to locate the registers.
 *     An interrupt is triggered to autoprobe for the interrupt
 *     line.
 *
 * 2.  With command line overrides - t128=address,irq may be 
 *     used on the LILO command line to override the defaults.
 *
 * 3.  With the T128_OVERRIDE compile time define.  This is 
 *     specified as an array of address, irq tuples.  Ie, for
 *     one board at the default 0xcc000 address, IRQ5, I could say 
 *     -DT128_OVERRIDE={{0xcc000, 5}}
 *	
 *     Note that if the override methods are used, place holders must
 *     be specified for other boards in the system.
 * 
 * T128/T128F jumper/dipswitch settings (note : on my sample, the switches 
 * were epoxy'd shut, meaning I couldn't change the 0xcc000 base address) :
 *
 * T128    Sw7 Sw8 Sw6 = 0ws Sw5 = boot 
 * T128F   Sw6 Sw7 Sw5 = 0ws Sw4 = boot Sw8 = floppy disable
 * cc000   off off      
 * c8000   off on
 * dc000   on  off
 * d8000   on  on
 *
 * 
 * Interrupts 
 * There is a 12 pin jumper block, jp1, numbered as follows : 
 *   T128 (JP1)  	 T128F (J5)
 * 2 4 6 8 10 12	11 9  7 5 3 1
 * 1 3 5 7 9  11	12 10 8 6 4 2
 *
 * 3   2-4
 * 5   1-3
 * 7   3-5
 * T128F only 
 * 10 8-10
 * 12 7-9
 * 14 10-12
 * 15 9-11
 */
 
#include <linux/signal.h>
#include <linux/io.h>
#include <linux/blkdev.h>
#include <linux/interrupt.h>
#include <linux/stat.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/delay.h>

#include <scsi/scsi_host.h>
#include "t128.h"
#define AUTOPROBE_IRQ
#include "NCR5380.h"

static struct override {
    unsigned long address;
    int irq;
} overrides
#ifdef T128_OVERRIDE
    [] __initdata = T128_OVERRIDE;
#else
    [4] __initdata = {{0, IRQ_AUTO}, {0, IRQ_AUTO},
        {0 ,IRQ_AUTO}, {0, IRQ_AUTO}};
#endif

#define NO_OVERRIDES ARRAY_SIZE(overrides)

static struct base {
    unsigned int address;
    int noauto;
} bases[] __initdata = {
    { 0xcc000, 0}, { 0xc8000, 0}, { 0xdc000, 0}, { 0xd8000, 0}
};

#define NO_BASES ARRAY_SIZE(bases)

static struct signature {
    const char *string;
    int offset;
} signatures[] __initdata = {
{"TSROM: SCSI BIOS, Version 1.12", 0x36},
};

#define NO_SIGNATURES ARRAY_SIZE(signatures)

#ifndef MODULE
/*
 * Function : t128_setup(char *str, int *ints)
 *
 * Purpose : LILO command line initialization of the overrides array,
 * 
 * Inputs : str - unused, ints - array of integer parameters with ints[0]
 *	equal to the number of ints.
 *
 */

static int __init t128_setup(char *str)
{
    static int commandline_current = 0;
    int i;
    int ints[10];

    get_options(str, ARRAY_SIZE(ints), ints);
    if (ints[0] != 2) 
	printk("t128_setup : usage t128=address,irq\n");
    else 
	if (commandline_current < NO_OVERRIDES) {
	    overrides[commandline_current].address = ints[1];
	    overrides[commandline_current].irq = ints[2];
	    for (i = 0; i < NO_BASES; ++i)
		if (bases[i].address == ints[1]) {
		    bases[i].noauto = 1;
		    break;
		}
	    ++commandline_current;
	}
    return 1;
}

__setup("t128=", t128_setup);
#endif

/* 
 * Function : int t128_detect(struct scsi_host_template * tpnt)
 *
 * Purpose : detects and initializes T128,T128F, or T228 controllers
 *	that were autoprobed, overridden on the LILO command line, 
 *	or specified at compile time.
 *
 * Inputs : tpnt - template for this SCSI adapter.
 * 
 * Returns : 1 if a host adapter was found, 0 if not.
 *
 */

static int __init t128_detect(struct scsi_host_template *tpnt)
{
    static int current_override = 0, current_base = 0;
    struct Scsi_Host *instance;
    unsigned long base;
    void __iomem *p;
    int sig, count;

    for (count = 0; current_override < NO_OVERRIDES; ++current_override) {
	base = 0;
	p = NULL;

	if (overrides[current_override].address) {
	    base = overrides[current_override].address;
	    p = ioremap(bases[current_base].address, 0x2000);
	    if (!p)
		base = 0;
	} else 
	    for (; !base && (current_base < NO_BASES); ++current_base) {
#if (TDEBUG & TDEBUG_INIT)
    printk("scsi-t128 : probing address %08x\n", bases[current_base].address);
#endif
		if (bases[current_base].noauto)
			continue;
		p = ioremap(bases[current_base].address, 0x2000);
		if (!p)
			continue;
		for (sig = 0; sig < NO_SIGNATURES; ++sig) 
		    if (check_signature(p + signatures[sig].offset,
					signatures[sig].string,
					strlen(signatures[sig].string))) {
			base = bases[current_base].address;
#if (TDEBUG & TDEBUG_INIT)
			printk("scsi-t128 : detected board.\n");
#endif
			goto found;
		    }
		iounmap(p);
	    }

#if defined(TDEBUG) && (TDEBUG & TDEBUG_INIT)
	printk("scsi-t128 : base = %08x\n", (unsigned int) base);
#endif

	if (!base)
	    break;

found:
	instance = scsi_register (tpnt, sizeof(struct NCR5380_hostdata));
	if(instance == NULL)
		break;
		
	instance->base = base;
	((struct NCR5380_hostdata *)instance->hostdata)->base = p;

	NCR5380_init(instance, 0);

	if (overrides[current_override].irq != IRQ_AUTO)
	    instance->irq = overrides[current_override].irq;
	else 
	    instance->irq = NCR5380_probe_irq(instance, T128_IRQS);

	/* Compatibility with documented NCR5380 kernel parameters */
	if (instance->irq == 255)
		instance->irq = NO_IRQ;

	if (instance->irq != NO_IRQ)
	    if (request_irq(instance->irq, t128_intr, 0, "t128",
			    instance)) {
		printk("scsi%d : IRQ%d not free, interrupts disabled\n", 
		    instance->host_no, instance->irq);
		instance->irq = NO_IRQ;
	    } 

	if (instance->irq == NO_IRQ) {
	    printk("scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
	    printk("scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
	}

#if defined(TDEBUG) && (TDEBUG & TDEBUG_INIT)
	printk("scsi%d : irq = %d\n", instance->host_no, instance->irq);
#endif

	++current_override;
	++count;
    }
    return count;
}

static int t128_release(struct Scsi_Host *shost)
{
	NCR5380_local_declare();
	NCR5380_setup(shost);
	if (shost->irq != NO_IRQ)
		free_irq(shost->irq, shost);
	NCR5380_exit(shost);
	if (shost->io_port && shost->n_io_port)
		release_region(shost->io_port, shost->n_io_port);
	scsi_unregister(shost);
	iounmap(base);
	return 0;
}

/*
 * Function : int t128_biosparam(Disk * disk, struct block_device *dev, int *ip)
 *
 * Purpose : Generates a BIOS / DOS compatible H-C-S mapping for 
 *	the specified device / size.
 * 
 * Inputs : size = size of device in sectors (512 bytes), dev = block device
 *	major / minor, ip[] = {heads, sectors, cylinders}  
 *
 * Returns : always 0 (success), initializes ip
 *	
 */

/* 
 * XXX Most SCSI boards use this mapping, I could be incorrect.  Some one
 * using hard disks on a trantor should verify that this mapping corresponds
 * to that used by the BIOS / ASPI driver by running the linux fdisk program
 * and matching the H_C_S coordinates to what DOS uses.
 */

static int t128_biosparam(struct scsi_device *sdev, struct block_device *bdev,
                          sector_t capacity, int *ip)
{
  ip[0] = 64;
  ip[1] = 32;
  ip[2] = capacity >> 11;
  return 0;
}

/*
 * Function : int NCR5380_pread (struct Scsi_Host *instance, 
 *	unsigned char *dst, int len)
 *
 * Purpose : Fast 5380 pseudo-dma read function, transfers len bytes to 
 *	dst
 * 
 * Inputs : dst = destination, len = length in bytes
 *
 * Returns : 0 on success, non zero on a failure such as a watchdog 
 * 	timeout.
 */

static inline int NCR5380_pread (struct Scsi_Host *instance, unsigned char *dst,
    int len) {
    NCR5380_local_declare();
    void __iomem *reg;
    unsigned char *d = dst;
    register int i = len;

    NCR5380_setup(instance);
    reg = base + T_DATA_REG_OFFSET;

#if 0
    for (; i; --i) {
	while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
#else
    while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
    for (; i; --i) {
#endif
	*d++ = readb(reg);
    }

    if (readb(base + T_STATUS_REG_OFFSET) & T_ST_TIM) {
	unsigned char tmp;
	void __iomem *foo = base + T_CONTROL_REG_OFFSET;
	tmp = readb(foo);
	writeb(tmp | T_CR_CT, foo);
	writeb(tmp, foo);
	printk("scsi%d : watchdog timer fired in NCR5380_pread()\n",
	    instance->host_no);
	return -1;
    } else
	return 0;
}

/*
 * Function : int NCR5380_pwrite (struct Scsi_Host *instance, 
 *	unsigned char *src, int len)
 *
 * Purpose : Fast 5380 pseudo-dma write function, transfers len bytes from
 *	src
 * 
 * Inputs : src = source, len = length in bytes
 *
 * Returns : 0 on success, non zero on a failure such as a watchdog 
 * 	timeout.
 */

static inline int NCR5380_pwrite (struct Scsi_Host *instance, unsigned char *src,
    int len) {
    NCR5380_local_declare();
    void __iomem *reg;
    unsigned char *s = src;
    register int i = len;

    NCR5380_setup(instance);
    reg = base + T_DATA_REG_OFFSET;

#if 0
    for (; i; --i) {
	while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
#else
    while (!(readb(base+T_STATUS_REG_OFFSET) & T_ST_RDY)) barrier();
    for (; i; --i) {
#endif
	writeb(*s++, reg);
    }

    if (readb(base + T_STATUS_REG_OFFSET) & T_ST_TIM) {
	unsigned char tmp;
	void __iomem *foo = base + T_CONTROL_REG_OFFSET;
	tmp = readb(foo);
	writeb(tmp | T_CR_CT, foo);
	writeb(tmp, foo);
	printk("scsi%d : watchdog timer fired in NCR5380_pwrite()\n",
	    instance->host_no);
	return -1;
    } else 
	return 0;
}

MODULE_LICENSE("GPL");

#include "NCR5380.c"

static struct scsi_host_template driver_template = {
	.name           = "Trantor T128/T128F/T228",
	.detect         = t128_detect,
	.release        = t128_release,
	.proc_name      = "t128",
	.show_info      = t128_show_info,
	.write_info     = t128_write_info,
	.info           = t128_info,
	.queuecommand   = t128_queue_command,
	.eh_abort_handler = t128_abort,
	.eh_bus_reset_handler    = t128_bus_reset,
	.bios_param     = t128_biosparam,
	.can_queue      = CAN_QUEUE,
        .this_id        = 7,
	.sg_tablesize   = SG_ALL,
	.cmd_per_lun    = CMD_PER_LUN,
	.use_clustering = DISABLE_CLUSTERING,
};
#include "scsi_module.c"