blob: d1f377f5d3b61b6f2cbeb575cb9aa02a8992d821 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001config H8300
2 bool
3 default y
Sam Ravnborgec7748b2008-02-09 10:46:40 +01004 select HAVE_IDE
Thomas Gleixner51f3f152011-01-19 12:26:32 +01005 select HAVE_GENERIC_HARDIRQS
Thomas Gleixner9f7b2182011-03-24 19:15:36 +01006 select GENERIC_IRQ_SHOW
Linus Torvalds1da177e2005-04-16 15:20:36 -07007
Alan Jenkins9e1b9b82009-11-07 21:03:54 +00008config SYMBOL_PREFIX
9 string
10 default "_"
11
Linus Torvalds1da177e2005-04-16 15:20:36 -070012config MMU
13 bool
14 default n
15
16config SWAP
17 bool
18 default n
19
Christoph Lameter66701b12007-02-10 01:43:09 -080020config ZONE_DMA
21 bool
22 default y
23
Linus Torvalds1da177e2005-04-16 15:20:36 -070024config FPU
25 bool
26 default n
27
Linus Torvalds1da177e2005-04-16 15:20:36 -070028config RWSEM_GENERIC_SPINLOCK
29 bool
30 default y
31
32config RWSEM_XCHGADD_ALGORITHM
33 bool
34 default n
35
David Howellsf0d1b0b2006-12-08 02:37:49 -080036config ARCH_HAS_ILOG2_U32
37 bool
38 default n
39
40config ARCH_HAS_ILOG2_U64
41 bool
42 default n
43
Akinobu Mitaf6e02132006-03-26 01:39:23 -080044config GENERIC_HWEIGHT
45 bool
46 default y
47
Linus Torvalds1da177e2005-04-16 15:20:36 -070048config GENERIC_CALIBRATE_DELAY
49 bool
50 default y
51
Yoshinori Sato9791af52008-10-15 22:01:17 -070052config GENERIC_BUG
53 bool
54 depends on BUG
55
Ingo Molnar06027bd2006-02-14 13:53:15 -080056config TIME_LOW_RES
57 bool
58 default y
59
Al Viro5ea81762007-02-11 15:41:31 +000060config NO_IOPORT
61 def_bool y
62
Dan Williams1b0fac42007-07-15 23:40:26 -070063config NO_DMA
64 def_bool y
65
Linus Torvalds1da177e2005-04-16 15:20:36 -070066config ISA
67 bool
68 default y
69
70config PCI
71 bool
72 default n
73
H. Peter Anvinbdc80782008-02-08 04:21:26 -080074config HZ
75 int
76 default 100
77
Linus Torvalds1da177e2005-04-16 15:20:36 -070078source "init/Kconfig"
79
Matt Helsleydc52ddc2008-10-18 20:27:21 -070080source "kernel/Kconfig.freezer"
81
Linus Torvalds1da177e2005-04-16 15:20:36 -070082source "arch/h8300/Kconfig.cpu"
83
84menu "Executable file formats"
85
86source "fs/Kconfig.binfmt"
87
88endmenu
89
Sam Ravnborgd5950b42005-07-11 21:03:49 -070090source "net/Kconfig"
91
Linus Torvalds1da177e2005-04-16 15:20:36 -070092source "drivers/base/Kconfig"
93
94source "drivers/mtd/Kconfig"
95
96source "drivers/block/Kconfig"
97
98source "drivers/ide/Kconfig"
99
100source "arch/h8300/Kconfig.ide"
101
Sam Ravnborgd5950b42005-07-11 21:03:49 -0700102source "drivers/net/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700103
104#
105# input - input/joystick depends on it. As does USB.
106#
107source "drivers/input/Kconfig"
108
109menu "Character devices"
110
111config VT
112 bool "Virtual terminal"
113 ---help---
114 If you say Y here, you will get support for terminal devices with
115 display and keyboard devices. These are called "virtual" because you
116 can run several virtual terminals (also called virtual consoles) on
117 one physical terminal. This is rather useful, for example one
118 virtual terminal can collect system messages and warnings, another
119 one can be used for a text-mode user session, and a third could run
120 an X session, all in parallel. Switching between virtual terminals
121 is done with certain key combinations, usually Alt-<function key>.
122
123 The setterm command ("man setterm") can be used to change the
124 properties (such as colors or beeping) of a virtual terminal. The
125 man page console_codes(4) ("man console_codes") contains the special
126 character sequences that can be used to change those properties
127 directly. The fonts used on virtual terminals can be changed with
128 the setfont ("man setfont") command and the key bindings are defined
129 with the loadkeys ("man loadkeys") command.
130
131 You need at least one virtual terminal device in order to make use
132 of your keyboard and monitor. Therefore, only people configuring an
133 embedded system would want to say N here in order to save some
134 memory; the only way to log into such a system is then via a serial
135 or network connection.
136
137 If unsure, say Y, or else you won't be able to do much with your new
138 shiny Linux system :-)
139
140config VT_CONSOLE
141 bool "Support for console on virtual terminal"
142 depends on VT
143 ---help---
144 The system console is the device which receives all kernel messages
145 and warnings and which allows logins in single user mode. If you
146 answer Y here, a virtual terminal (the device used to interact with
147 a physical terminal) can be used as system console. This is the most
148 common mode of operations, so you should say Y here unless you want
149 the kernel messages be output only to a serial port (in which case
150 you should say Y to "Console on serial port", below).
151
152 If you do say Y here, by default the currently visible virtual
153 terminal (/dev/tty0) will be used as system console. You can change
154 that with a kernel command line option such as "console=tty3" which
155 would use the third virtual terminal as system console. (Try "man
156 bootparam" or see the documentation of your boot loader (lilo or
157 loadlin) about how to pass options to the kernel at boot time.)
158
159 If unsure, say Y.
160
161config HW_CONSOLE
162 bool
Paul Bolle75330692011-10-12 14:25:31 +0200163 depends on VT
Linus Torvalds1da177e2005-04-16 15:20:36 -0700164 default y
165
166comment "Unix98 PTY support"
167
168config UNIX98_PTYS
169 bool "Unix98 PTY support"
170 ---help---
171 A pseudo terminal (PTY) is a software device consisting of two
172 halves: a master and a slave. The slave device behaves identical to
173 a physical terminal; the master device is used by a process to
174 read data from and write data to the slave, thereby emulating a
175 terminal. Typical programs for the master side are telnet servers
176 and xterms.
177
178 Linux has traditionally used the BSD-like names /dev/ptyxx for
179 masters and /dev/ttyxx for slaves of pseudo terminals. This scheme
180 has a number of problems. The GNU C library glibc 2.1 and later,
181 however, supports the Unix98 naming standard: in order to acquire a
182 pseudo terminal, a process opens /dev/ptmx; the number of the pseudo
183 terminal is then made available to the process and the pseudo
184 terminal slave can be accessed as /dev/pts/<number>. What was
185 traditionally /dev/ttyp2 will then be /dev/pts/2, for example.
186
187 The entries in /dev/pts/ are created on the fly by a virtual
188 file system; therefore, if you say Y here you should say Y to
189 "/dev/pts file system for Unix98 PTYs" as well.
190
191 If you want to say Y here, you need to have the C library glibc 2.1
192 or later (equal to libc-6.1, check with "ls -l /lib/libc.so.*").
193 Read the instructions in <file:Documentation/Changes> pertaining to
194 pseudo terminals. It's safe to say N.
195
Linus Torvalds1da177e2005-04-16 15:20:36 -0700196source "drivers/char/pcmcia/Kconfig"
197
Paul Bollea4a77b12011-10-11 13:23:29 +0200198source "drivers/tty/serial/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700199
200source "drivers/i2c/Kconfig"
201
Jean Delvaread2f9312005-07-02 18:15:49 +0200202source "drivers/hwmon/Kconfig"
203
Linus Torvalds1da177e2005-04-16 15:20:36 -0700204source "drivers/usb/Kconfig"
205
Greg Kroah-Hartman2f86c3e2008-09-17 16:34:11 +0100206source "drivers/uwb/Kconfig"
207
Linus Torvalds1da177e2005-04-16 15:20:36 -0700208endmenu
209
F. Duncan M. Haldane6e38a2b2008-11-07 18:17:51 -0500210source "drivers/staging/Kconfig"
211
Linus Torvalds1da177e2005-04-16 15:20:36 -0700212source "fs/Kconfig"
213
Linus Torvalds1da177e2005-04-16 15:20:36 -0700214source "arch/h8300/Kconfig.debug"
215
216source "security/Kconfig"
217
218source "crypto/Kconfig"
219
220source "lib/Kconfig"