blob: 63ffb002ec673d3858e36177b8e3ed6bb20e6cca [file] [log] [blame]
Abhilash Kesavan155bf482010-07-13 13:23:05 +09001/*
2 * Copyright (c) 2010 Samsung Electronics Co., Ltd.
3 * http://www.samsung.com
4 *
5 * PATA driver for Samsung SoCs.
6 * Supports CF Interface in True IDE mode. Currently only PIO mode has been
7 * implemented; UDMA support has to be added.
8 *
9 * Based on:
10 * PATA driver for AT91SAM9260 Static Memory Controller
11 * PATA driver for Toshiba SCC controller
12 *
13 * This program is free software; you can redistribute it and/or modify it
14 * under the terms of the GNU General Public License version 2
15 * as published by the Free Software Foundation.
16*/
17
18#include <linux/kernel.h>
19#include <linux/module.h>
20#include <linux/init.h>
21#include <linux/clk.h>
22#include <linux/libata.h>
23#include <linux/platform_device.h>
24#include <linux/slab.h>
25
Arnd Bergmann436d42c2012-08-24 15:22:12 +020026#include <linux/platform_data/ata-samsung_cf.h>
Abhilash Kesavan155bf482010-07-13 13:23:05 +090027#include <plat/regs-ata.h>
28
29#define DRV_NAME "pata_samsung_cf"
30#define DRV_VERSION "0.1"
31
32enum s3c_cpu_type {
33 TYPE_S3C64XX,
34 TYPE_S5PC100,
35 TYPE_S5PV210,
36};
37
38/*
39 * struct s3c_ide_info - S3C PATA instance.
40 * @clk: The clock resource for this controller.
41 * @ide_addr: The area mapped for the hardware registers.
42 * @sfr_addr: The area mapped for the special function registers.
43 * @irq: The IRQ number we are using.
44 * @cpu_type: The exact type of this controller.
45 * @fifo_status_reg: The ATA_FIFO_STATUS register offset.
46 */
47struct s3c_ide_info {
48 struct clk *clk;
49 void __iomem *ide_addr;
50 void __iomem *sfr_addr;
51 unsigned int irq;
52 enum s3c_cpu_type cpu_type;
53 unsigned int fifo_status_reg;
54};
55
56static void pata_s3c_set_endian(void __iomem *s3c_ide_regbase, u8 mode)
57{
58 u32 reg = readl(s3c_ide_regbase + S3C_ATA_CFG);
59 reg = mode ? (reg & ~S3C_ATA_CFG_SWAP) : (reg | S3C_ATA_CFG_SWAP);
60 writel(reg, s3c_ide_regbase + S3C_ATA_CFG);
61}
62
63static void pata_s3c_cfg_mode(void __iomem *s3c_ide_sfrbase)
64{
65 /* Select true-ide as the internal operating mode */
66 writel(readl(s3c_ide_sfrbase + S3C_CFATA_MUX) | S3C_CFATA_MUX_TRUEIDE,
67 s3c_ide_sfrbase + S3C_CFATA_MUX);
68}
69
70static unsigned long
71pata_s3c_setup_timing(struct s3c_ide_info *info, const struct ata_timing *ata)
72{
73 int t1 = ata->setup;
74 int t2 = ata->act8b;
75 int t2i = ata->rec8b;
76 ulong piotime;
77
78 piotime = ((t2i & 0xff) << 12) | ((t2 & 0xff) << 4) | (t1 & 0xf);
79
80 return piotime;
81}
82
83static void pata_s3c_set_piomode(struct ata_port *ap, struct ata_device *adev)
84{
85 struct s3c_ide_info *info = ap->host->private_data;
86 struct ata_timing timing;
87 int cycle_time;
88 ulong ata_cfg = readl(info->ide_addr + S3C_ATA_CFG);
89 ulong piotime;
90
91 /* Enables IORDY if mode requires it */
92 if (ata_pio_need_iordy(adev))
93 ata_cfg |= S3C_ATA_CFG_IORDYEN;
94 else
95 ata_cfg &= ~S3C_ATA_CFG_IORDYEN;
96
97 cycle_time = (int)(1000000000UL / clk_get_rate(info->clk));
98
99 ata_timing_compute(adev, adev->pio_mode, &timing,
100 cycle_time * 1000, 0);
101
102 piotime = pata_s3c_setup_timing(info, &timing);
103
104 writel(ata_cfg, info->ide_addr + S3C_ATA_CFG);
105 writel(piotime, info->ide_addr + S3C_ATA_PIO_TIME);
106}
107
108/*
109 * Waits until the IDE controller is able to perform next read/write
110 * operation to the disk. Needed for 64XX series boards only.
111 */
112static int wait_for_host_ready(struct s3c_ide_info *info)
113{
114 ulong timeout;
115 void __iomem *fifo_reg = info->ide_addr + info->fifo_status_reg;
116
117 /* wait for maximum of 20 msec */
118 timeout = jiffies + msecs_to_jiffies(20);
119 while (time_before(jiffies, timeout)) {
120 if ((readl(fifo_reg) >> 28) == 0)
121 return 0;
122 }
123 return -EBUSY;
124}
125
126/*
127 * Writes to one of the task file registers.
128 */
129static void ata_outb(struct ata_host *host, u8 addr, void __iomem *reg)
130{
131 struct s3c_ide_info *info = host->private_data;
132
133 wait_for_host_ready(info);
134 writeb(addr, reg);
135}
136
137/*
138 * Reads from one of the task file registers.
139 */
140static u8 ata_inb(struct ata_host *host, void __iomem *reg)
141{
142 struct s3c_ide_info *info = host->private_data;
143 u8 temp;
144
145 wait_for_host_ready(info);
146 (void) readb(reg);
147 wait_for_host_ready(info);
148 temp = readb(info->ide_addr + S3C_ATA_PIO_RDATA);
149 return temp;
150}
151
152/*
153 * pata_s3c_tf_load - send taskfile registers to host controller
154 */
155static void pata_s3c_tf_load(struct ata_port *ap,
156 const struct ata_taskfile *tf)
157{
158 struct ata_ioports *ioaddr = &ap->ioaddr;
159 unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
160
161 if (tf->ctl != ap->last_ctl) {
162 ata_outb(ap->host, tf->ctl, ioaddr->ctl_addr);
163 ap->last_ctl = tf->ctl;
164 ata_wait_idle(ap);
165 }
166
167 if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
168 ata_outb(ap->host, tf->hob_feature, ioaddr->feature_addr);
169 ata_outb(ap->host, tf->hob_nsect, ioaddr->nsect_addr);
170 ata_outb(ap->host, tf->hob_lbal, ioaddr->lbal_addr);
171 ata_outb(ap->host, tf->hob_lbam, ioaddr->lbam_addr);
172 ata_outb(ap->host, tf->hob_lbah, ioaddr->lbah_addr);
173 }
174
175 if (is_addr) {
176 ata_outb(ap->host, tf->feature, ioaddr->feature_addr);
177 ata_outb(ap->host, tf->nsect, ioaddr->nsect_addr);
178 ata_outb(ap->host, tf->lbal, ioaddr->lbal_addr);
179 ata_outb(ap->host, tf->lbam, ioaddr->lbam_addr);
180 ata_outb(ap->host, tf->lbah, ioaddr->lbah_addr);
181 }
182
183 if (tf->flags & ATA_TFLAG_DEVICE)
184 ata_outb(ap->host, tf->device, ioaddr->device_addr);
185
186 ata_wait_idle(ap);
187}
188
189/*
190 * pata_s3c_tf_read - input device's ATA taskfile shadow registers
191 */
192static void pata_s3c_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
193{
194 struct ata_ioports *ioaddr = &ap->ioaddr;
195
196 tf->feature = ata_inb(ap->host, ioaddr->error_addr);
197 tf->nsect = ata_inb(ap->host, ioaddr->nsect_addr);
198 tf->lbal = ata_inb(ap->host, ioaddr->lbal_addr);
199 tf->lbam = ata_inb(ap->host, ioaddr->lbam_addr);
200 tf->lbah = ata_inb(ap->host, ioaddr->lbah_addr);
201 tf->device = ata_inb(ap->host, ioaddr->device_addr);
202
203 if (tf->flags & ATA_TFLAG_LBA48) {
204 ata_outb(ap->host, tf->ctl | ATA_HOB, ioaddr->ctl_addr);
205 tf->hob_feature = ata_inb(ap->host, ioaddr->error_addr);
206 tf->hob_nsect = ata_inb(ap->host, ioaddr->nsect_addr);
207 tf->hob_lbal = ata_inb(ap->host, ioaddr->lbal_addr);
208 tf->hob_lbam = ata_inb(ap->host, ioaddr->lbam_addr);
209 tf->hob_lbah = ata_inb(ap->host, ioaddr->lbah_addr);
210 ata_outb(ap->host, tf->ctl, ioaddr->ctl_addr);
211 ap->last_ctl = tf->ctl;
212 }
213}
214
215/*
216 * pata_s3c_exec_command - issue ATA command to host controller
217 */
218static void pata_s3c_exec_command(struct ata_port *ap,
219 const struct ata_taskfile *tf)
220{
221 ata_outb(ap->host, tf->command, ap->ioaddr.command_addr);
222 ata_sff_pause(ap);
223}
224
225/*
226 * pata_s3c_check_status - Read device status register
227 */
228static u8 pata_s3c_check_status(struct ata_port *ap)
229{
230 return ata_inb(ap->host, ap->ioaddr.status_addr);
231}
232
233/*
234 * pata_s3c_check_altstatus - Read alternate device status register
235 */
236static u8 pata_s3c_check_altstatus(struct ata_port *ap)
237{
238 return ata_inb(ap->host, ap->ioaddr.altstatus_addr);
239}
240
241/*
242 * pata_s3c_data_xfer - Transfer data by PIO
243 */
244unsigned int pata_s3c_data_xfer(struct ata_device *dev, unsigned char *buf,
245 unsigned int buflen, int rw)
246{
247 struct ata_port *ap = dev->link->ap;
248 struct s3c_ide_info *info = ap->host->private_data;
249 void __iomem *data_addr = ap->ioaddr.data_addr;
250 unsigned int words = buflen >> 1, i;
251 u16 *data_ptr = (u16 *)buf;
252
253 /* Requires wait same as in ata_inb/ata_outb */
254 if (rw == READ)
255 for (i = 0; i < words; i++, data_ptr++) {
256 wait_for_host_ready(info);
257 (void) readw(data_addr);
258 wait_for_host_ready(info);
259 *data_ptr = readw(info->ide_addr
260 + S3C_ATA_PIO_RDATA);
261 }
262 else
263 for (i = 0; i < words; i++, data_ptr++) {
264 wait_for_host_ready(info);
265 writew(*data_ptr, data_addr);
266 }
267
268 if (buflen & 0x01)
269 dev_err(ap->dev, "unexpected trailing data\n");
270
271 return words << 1;
272}
273
274/*
275 * pata_s3c_dev_select - Select device on ATA bus
276 */
277static void pata_s3c_dev_select(struct ata_port *ap, unsigned int device)
278{
279 u8 tmp = ATA_DEVICE_OBS;
280
281 if (device != 0)
282 tmp |= ATA_DEV1;
283
284 ata_outb(ap->host, tmp, ap->ioaddr.device_addr);
285 ata_sff_pause(ap);
286}
287
288/*
289 * pata_s3c_devchk - PATA device presence detection
290 */
291static unsigned int pata_s3c_devchk(struct ata_port *ap,
292 unsigned int device)
293{
294 struct ata_ioports *ioaddr = &ap->ioaddr;
295 u8 nsect, lbal;
296
297 pata_s3c_dev_select(ap, device);
298
299 ata_outb(ap->host, 0x55, ioaddr->nsect_addr);
300 ata_outb(ap->host, 0xaa, ioaddr->lbal_addr);
301
302 ata_outb(ap->host, 0xaa, ioaddr->nsect_addr);
303 ata_outb(ap->host, 0x55, ioaddr->lbal_addr);
304
305 ata_outb(ap->host, 0x55, ioaddr->nsect_addr);
306 ata_outb(ap->host, 0xaa, ioaddr->lbal_addr);
307
308 nsect = ata_inb(ap->host, ioaddr->nsect_addr);
309 lbal = ata_inb(ap->host, ioaddr->lbal_addr);
310
311 if ((nsect == 0x55) && (lbal == 0xaa))
312 return 1; /* we found a device */
313
314 return 0; /* nothing found */
315}
316
317/*
318 * pata_s3c_wait_after_reset - wait for devices to become ready after reset
319 */
320static int pata_s3c_wait_after_reset(struct ata_link *link,
321 unsigned long deadline)
322{
323 int rc;
324
Tejun Heo97750ce2010-09-06 17:56:29 +0200325 ata_msleep(link->ap, ATA_WAIT_AFTER_RESET);
Abhilash Kesavan155bf482010-07-13 13:23:05 +0900326
327 /* always check readiness of the master device */
328 rc = ata_sff_wait_ready(link, deadline);
329 /* -ENODEV means the odd clown forgot the D7 pulldown resistor
330 * and TF status is 0xff, bail out on it too.
331 */
332 if (rc)
333 return rc;
334
335 return 0;
336}
337
338/*
339 * pata_s3c_bus_softreset - PATA device software reset
340 */
341static unsigned int pata_s3c_bus_softreset(struct ata_port *ap,
342 unsigned long deadline)
343{
344 struct ata_ioports *ioaddr = &ap->ioaddr;
345
346 /* software reset. causes dev0 to be selected */
347 ata_outb(ap->host, ap->ctl, ioaddr->ctl_addr);
348 udelay(20);
349 ata_outb(ap->host, ap->ctl | ATA_SRST, ioaddr->ctl_addr);
350 udelay(20);
351 ata_outb(ap->host, ap->ctl, ioaddr->ctl_addr);
352 ap->last_ctl = ap->ctl;
353
354 return pata_s3c_wait_after_reset(&ap->link, deadline);
355}
356
357/*
358 * pata_s3c_softreset - reset host port via ATA SRST
359 */
360static int pata_s3c_softreset(struct ata_link *link, unsigned int *classes,
361 unsigned long deadline)
362{
363 struct ata_port *ap = link->ap;
364 unsigned int devmask = 0;
365 int rc;
366 u8 err;
367
368 /* determine if device 0 is present */
369 if (pata_s3c_devchk(ap, 0))
370 devmask |= (1 << 0);
371
372 /* select device 0 again */
373 pata_s3c_dev_select(ap, 0);
374
375 /* issue bus reset */
376 rc = pata_s3c_bus_softreset(ap, deadline);
377 /* if link is occupied, -ENODEV too is an error */
378 if (rc && rc != -ENODEV) {
Joe Perchesa9a79df2011-04-15 15:51:59 -0700379 ata_link_err(link, "SRST failed (errno=%d)\n", rc);
Abhilash Kesavan155bf482010-07-13 13:23:05 +0900380 return rc;
381 }
382
383 /* determine by signature whether we have ATA or ATAPI devices */
384 classes[0] = ata_sff_dev_classify(&ap->link.device[0],
385 devmask & (1 << 0), &err);
386
387 return 0;
388}
389
390/*
391 * pata_s3c_set_devctl - Write device control register
392 */
393static void pata_s3c_set_devctl(struct ata_port *ap, u8 ctl)
394{
395 ata_outb(ap->host, ctl, ap->ioaddr.ctl_addr);
396}
397
398static struct scsi_host_template pata_s3c_sht = {
399 ATA_PIO_SHT(DRV_NAME),
400};
401
402static struct ata_port_operations pata_s3c_port_ops = {
403 .inherits = &ata_sff_port_ops,
404 .sff_check_status = pata_s3c_check_status,
405 .sff_check_altstatus = pata_s3c_check_altstatus,
406 .sff_tf_load = pata_s3c_tf_load,
407 .sff_tf_read = pata_s3c_tf_read,
408 .sff_data_xfer = pata_s3c_data_xfer,
409 .sff_exec_command = pata_s3c_exec_command,
410 .sff_dev_select = pata_s3c_dev_select,
411 .sff_set_devctl = pata_s3c_set_devctl,
412 .softreset = pata_s3c_softreset,
413 .set_piomode = pata_s3c_set_piomode,
414};
415
416static struct ata_port_operations pata_s5p_port_ops = {
417 .inherits = &ata_sff_port_ops,
418 .set_piomode = pata_s3c_set_piomode,
419};
420
421static void pata_s3c_enable(void *s3c_ide_regbase, bool state)
422{
423 u32 temp = readl(s3c_ide_regbase + S3C_ATA_CTRL);
424 temp = state ? (temp | 1) : (temp & ~1);
425 writel(temp, s3c_ide_regbase + S3C_ATA_CTRL);
426}
427
428static irqreturn_t pata_s3c_irq(int irq, void *dev_instance)
429{
430 struct ata_host *host = dev_instance;
431 struct s3c_ide_info *info = host->private_data;
432 u32 reg;
433
434 reg = readl(info->ide_addr + S3C_ATA_IRQ);
435 writel(reg, info->ide_addr + S3C_ATA_IRQ);
436
437 return ata_sff_interrupt(irq, dev_instance);
438}
439
440static void pata_s3c_hwinit(struct s3c_ide_info *info,
441 struct s3c_ide_platdata *pdata)
442{
443 switch (info->cpu_type) {
444 case TYPE_S3C64XX:
445 /* Configure as big endian */
446 pata_s3c_cfg_mode(info->sfr_addr);
447 pata_s3c_set_endian(info->ide_addr, 1);
448 pata_s3c_enable(info->ide_addr, true);
449 msleep(100);
450
451 /* Remove IRQ Status */
452 writel(0x1f, info->ide_addr + S3C_ATA_IRQ);
453 writel(0x1b, info->ide_addr + S3C_ATA_IRQ_MSK);
454 break;
455
456 case TYPE_S5PC100:
457 pata_s3c_cfg_mode(info->sfr_addr);
458 /* FALLTHROUGH */
459
460 case TYPE_S5PV210:
461 /* Configure as little endian */
462 pata_s3c_set_endian(info->ide_addr, 0);
463 pata_s3c_enable(info->ide_addr, true);
464 msleep(100);
465
466 /* Remove IRQ Status */
467 writel(0x3f, info->ide_addr + S3C_ATA_IRQ);
468 writel(0x3f, info->ide_addr + S3C_ATA_IRQ_MSK);
469 break;
470
471 default:
472 BUG();
473 }
474}
475
476static int __init pata_s3c_probe(struct platform_device *pdev)
477{
478 struct s3c_ide_platdata *pdata = pdev->dev.platform_data;
479 struct device *dev = &pdev->dev;
480 struct s3c_ide_info *info;
481 struct resource *res;
482 struct ata_port *ap;
483 struct ata_host *host;
484 enum s3c_cpu_type cpu_type;
485 int ret;
486
487 cpu_type = platform_get_device_id(pdev)->driver_data;
488
489 info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
490 if (!info) {
491 dev_err(dev, "failed to allocate memory for device data\n");
492 return -ENOMEM;
493 }
494
495 info->irq = platform_get_irq(pdev, 0);
496
497 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
498 if (res == NULL) {
499 dev_err(dev, "failed to get mem resource\n");
500 return -EINVAL;
501 }
502
503 if (!devm_request_mem_region(dev, res->start,
504 resource_size(res), DRV_NAME)) {
505 dev_err(dev, "error requesting register region\n");
506 return -EBUSY;
507 }
508
509 info->ide_addr = devm_ioremap(dev, res->start, resource_size(res));
510 if (!info->ide_addr) {
511 dev_err(dev, "failed to map IO base address\n");
512 return -ENOMEM;
513 }
514
515 info->clk = clk_get(&pdev->dev, "cfcon");
516 if (IS_ERR(info->clk)) {
517 dev_err(dev, "failed to get access to cf controller clock\n");
518 ret = PTR_ERR(info->clk);
519 info->clk = NULL;
520 return ret;
521 }
522
523 clk_enable(info->clk);
524
525 /* init ata host */
526 host = ata_host_alloc(dev, 1);
527 if (!host) {
528 dev_err(dev, "failed to allocate ide host\n");
529 ret = -ENOMEM;
530 goto stop_clk;
531 }
532
533 ap = host->ports[0];
Abhilash Kesavan155bf482010-07-13 13:23:05 +0900534 ap->pio_mask = ATA_PIO4;
535
536 if (cpu_type == TYPE_S3C64XX) {
537 ap->ops = &pata_s3c_port_ops;
538 info->sfr_addr = info->ide_addr + 0x1800;
539 info->ide_addr += 0x1900;
540 info->fifo_status_reg = 0x94;
541 } else if (cpu_type == TYPE_S5PC100) {
542 ap->ops = &pata_s5p_port_ops;
543 info->sfr_addr = info->ide_addr + 0x1800;
544 info->ide_addr += 0x1900;
545 info->fifo_status_reg = 0x84;
546 } else {
547 ap->ops = &pata_s5p_port_ops;
548 info->fifo_status_reg = 0x84;
549 }
550
551 info->cpu_type = cpu_type;
552
553 if (info->irq <= 0) {
554 ap->flags |= ATA_FLAG_PIO_POLLING;
555 info->irq = 0;
556 ata_port_desc(ap, "no IRQ, using PIO polling\n");
557 }
558
559 ap->ioaddr.cmd_addr = info->ide_addr + S3C_ATA_CMD;
560 ap->ioaddr.data_addr = info->ide_addr + S3C_ATA_PIO_DTR;
561 ap->ioaddr.error_addr = info->ide_addr + S3C_ATA_PIO_FED;
562 ap->ioaddr.feature_addr = info->ide_addr + S3C_ATA_PIO_FED;
563 ap->ioaddr.nsect_addr = info->ide_addr + S3C_ATA_PIO_SCR;
564 ap->ioaddr.lbal_addr = info->ide_addr + S3C_ATA_PIO_LLR;
565 ap->ioaddr.lbam_addr = info->ide_addr + S3C_ATA_PIO_LMR;
566 ap->ioaddr.lbah_addr = info->ide_addr + S3C_ATA_PIO_LHR;
567 ap->ioaddr.device_addr = info->ide_addr + S3C_ATA_PIO_DVR;
568 ap->ioaddr.status_addr = info->ide_addr + S3C_ATA_PIO_CSD;
569 ap->ioaddr.command_addr = info->ide_addr + S3C_ATA_PIO_CSD;
570 ap->ioaddr.altstatus_addr = info->ide_addr + S3C_ATA_PIO_DAD;
571 ap->ioaddr.ctl_addr = info->ide_addr + S3C_ATA_PIO_DAD;
572
573 ata_port_desc(ap, "mmio cmd 0x%llx ",
574 (unsigned long long)res->start);
575
576 host->private_data = info;
577
578 if (pdata && pdata->setup_gpio)
579 pdata->setup_gpio();
580
581 /* Set endianness and enable the interface */
582 pata_s3c_hwinit(info, pdata);
583
584 platform_set_drvdata(pdev, host);
585
586 return ata_host_activate(host, info->irq,
587 info->irq ? pata_s3c_irq : NULL,
588 0, &pata_s3c_sht);
589
590stop_clk:
591 clk_disable(info->clk);
592 clk_put(info->clk);
593 return ret;
594}
595
596static int __exit pata_s3c_remove(struct platform_device *pdev)
597{
598 struct ata_host *host = platform_get_drvdata(pdev);
599 struct s3c_ide_info *info = host->private_data;
600
601 ata_host_detach(host);
602
603 clk_disable(info->clk);
604 clk_put(info->clk);
605
606 return 0;
607}
608
609#ifdef CONFIG_PM
610static int pata_s3c_suspend(struct device *dev)
611{
612 struct platform_device *pdev = to_platform_device(dev);
613 struct ata_host *host = platform_get_drvdata(pdev);
614
615 return ata_host_suspend(host, PMSG_SUSPEND);
616}
617
618static int pata_s3c_resume(struct device *dev)
619{
620 struct platform_device *pdev = to_platform_device(dev);
621 struct ata_host *host = platform_get_drvdata(pdev);
622 struct s3c_ide_platdata *pdata = pdev->dev.platform_data;
623 struct s3c_ide_info *info = host->private_data;
624
625 pata_s3c_hwinit(info, pdata);
626 ata_host_resume(host);
627
628 return 0;
629}
630
631static const struct dev_pm_ops pata_s3c_pm_ops = {
632 .suspend = pata_s3c_suspend,
633 .resume = pata_s3c_resume,
634};
635#endif
636
637/* driver device registration */
638static struct platform_device_id pata_s3c_driver_ids[] = {
639 {
640 .name = "s3c64xx-pata",
641 .driver_data = TYPE_S3C64XX,
642 }, {
643 .name = "s5pc100-pata",
644 .driver_data = TYPE_S5PC100,
645 }, {
646 .name = "s5pv210-pata",
647 .driver_data = TYPE_S5PV210,
648 },
649 { }
650};
651
652MODULE_DEVICE_TABLE(platform, pata_s3c_driver_ids);
653
654static struct platform_driver pata_s3c_driver = {
655 .remove = __exit_p(pata_s3c_remove),
656 .id_table = pata_s3c_driver_ids,
657 .driver = {
658 .name = DRV_NAME,
659 .owner = THIS_MODULE,
660#ifdef CONFIG_PM
661 .pm = &pata_s3c_pm_ops,
662#endif
663 },
664};
665
666static int __init pata_s3c_init(void)
667{
668 return platform_driver_probe(&pata_s3c_driver, pata_s3c_probe);
669}
670
671static void __exit pata_s3c_exit(void)
672{
673 platform_driver_unregister(&pata_s3c_driver);
674}
675
676module_init(pata_s3c_init);
677module_exit(pata_s3c_exit);
678
679MODULE_AUTHOR("Abhilash Kesavan, <a.kesavan@samsung.com>");
680MODULE_DESCRIPTION("low-level driver for Samsung PATA controller");
681MODULE_LICENSE("GPL");
682MODULE_VERSION(DRV_VERSION);