arch/arm/boot/dts/qcom-apq8064.dtsi

/dts-v1/;

#include "skeleton.dtsi"
#include <dt-bindings/clock/qcom,gcc-msm8960.h>
#include <dt-bindings/reset/qcom,gcc-msm8960.h>
#include <dt-bindings/clock/qcom,mmcc-msm8960.h>
#include <dt-bindings/soc/qcom,gsbi.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
	model = "Qualcomm APQ8064";
	compatible = "qcom,apq8064";
	interrupt-parent = <&intc>;

	cpus {
		#address-cells = <1>;
		#size-cells = <0>;

		cpu@0 {
			compatible = "qcom,krait";
			enable-method = "qcom,kpss-acc-v1";
			device_type = "cpu";
			reg = <0>;
			next-level-cache = <&L2>;
			qcom,acc = <&acc0>;
			qcom,saw = <&saw0>;
			cpu-idle-states = <&CPU_SPC>;
		};

		cpu@1 {
			compatible = "qcom,krait";
			enable-method = "qcom,kpss-acc-v1";
			device_type = "cpu";
			reg = <1>;
			next-level-cache = <&L2>;
			qcom,acc = <&acc1>;
			qcom,saw = <&saw1>;
			cpu-idle-states = <&CPU_SPC>;
		};

		cpu@2 {
			compatible = "qcom,krait";
			enable-method = "qcom,kpss-acc-v1";
			device_type = "cpu";
			reg = <2>;
			next-level-cache = <&L2>;
			qcom,acc = <&acc2>;
			qcom,saw = <&saw2>;
			cpu-idle-states = <&CPU_SPC>;
		};

		cpu@3 {
			compatible = "qcom,krait";
			enable-method = "qcom,kpss-acc-v1";
			device_type = "cpu";
			reg = <3>;
			next-level-cache = <&L2>;
			qcom,acc = <&acc3>;
			qcom,saw = <&saw3>;
			cpu-idle-states = <&CPU_SPC>;
		};

		L2: l2-cache {
			compatible = "cache";
			cache-level = <2>;
		};

		idle-states {
			CPU_SPC: spc {
				compatible = "qcom,idle-state-spc",
						"arm,idle-state";
				entry-latency-us = <400>;
				exit-latency-us = <900>;
				min-residency-us = <3000>;
			};
		};
	};

	cpu-pmu {
		compatible = "qcom,krait-pmu";
		interrupts = <1 10 0x304>;
	};

	soc: soc {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;
		compatible = "simple-bus";

		tlmm_pinmux: pinctrl@800000 {
			compatible = "qcom,apq8064-pinctrl";
			reg = <0x800000 0x4000>;

			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			interrupts = <0 16 IRQ_TYPE_LEVEL_HIGH>;

			pinctrl-names = "default";
			pinctrl-0 = <&ps_hold>;

			sdc4_gpios: sdc4-gpios {
				pios {
					pins = "gpio63", "gpio64", "gpio65", "gpio66", "gpio67", "gpio68";
					function = "sdc4";
				};
			};

			ps_hold: ps_hold {
				mux {
					pins = "gpio78";
					function = "ps_hold";
				};
			};

			i2c1_pins: i2c1 {
				mux {
					pins = "gpio20", "gpio21";
					function = "gsbi1";
				};
			};

			i2c3_pins: i2c3 {
				mux {
					pins = "gpio8", "gpio9";
					function = "gsbi3";
				};
			};

			uart_pins: uart_pins {
				mux {
					pins = "gpio14", "gpio15", "gpio16", "gpio17";
					function = "gsbi6";
				};
			};
		};

		intc: interrupt-controller@2000000 {
			compatible = "qcom,msm-qgic2";
			interrupt-controller;
			#interrupt-cells = <3>;
			reg = <0x02000000 0x1000>,
			      <0x02002000 0x1000>;
		};

		timer@200a000 {
			compatible = "qcom,kpss-timer", "qcom,msm-timer";
			interrupts = <1 1 0x301>,
				     <1 2 0x301>,
				     <1 3 0x301>;
			reg = <0x0200a000 0x100>;
			clock-frequency = <27000000>,
					  <32768>;
			cpu-offset = <0x80000>;
		};

		acc0: clock-controller@2088000 {
			compatible = "qcom,kpss-acc-v1";
			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
		};

		acc1: clock-controller@2098000 {
			compatible = "qcom,kpss-acc-v1";
			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
		};

		acc2: clock-controller@20a8000 {
			compatible = "qcom,kpss-acc-v1";
			reg = <0x020a8000 0x1000>, <0x02008000 0x1000>;
		};

		acc3: clock-controller@20b8000 {
			compatible = "qcom,kpss-acc-v1";
			reg = <0x020b8000 0x1000>, <0x02008000 0x1000>;
		};

		saw0: power-controller@2089000 {
			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
			regulator;
		};

		saw1: power-controller@2099000 {
			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
			regulator;
		};

		saw2: power-controller@20a9000 {
			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
			reg = <0x020a9000 0x1000>, <0x02009000 0x1000>;
			regulator;
		};

		saw3: power-controller@20b9000 {
			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
			reg = <0x020b9000 0x1000>, <0x02009000 0x1000>;
			regulator;
		};

		gsbi1: gsbi@12440000 {
			status = "disabled";
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <1>;
			reg = <0x12440000 0x100>;
			clocks = <&gcc GSBI1_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			syscon-tcsr = <&tcsr>;

			i2c1: i2c@12460000 {
				compatible = "qcom,i2c-qup-v1.1.1";
				pinctrl-0 = <&i2c1_pins>;
				pinctrl-names = "default";
				reg = <0x12460000 0x1000>;
				interrupts = <0 194 IRQ_TYPE_NONE>;
				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
				clock-names = "core", "iface";
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		gsbi2: gsbi@12480000 {
			status = "disabled";
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <2>;
			reg = <0x12480000 0x100>;
			clocks = <&gcc GSBI2_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			syscon-tcsr = <&tcsr>;

			i2c2: i2c@124a0000 {
				compatible = "qcom,i2c-qup-v1.1.1";
				reg = <0x124a0000 0x1000>;
				interrupts = <0 196 IRQ_TYPE_NONE>;
				clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
				clock-names = "core", "iface";
				#address-cells = <1>;
				#size-cells = <0>;
			};
		};

		gsbi3: gsbi@16200000 {
			status = "disabled";
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <3>;
			reg = <0x16200000 0x100>;
			clocks = <&gcc GSBI3_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;
			i2c3: i2c@16280000 {
				compatible = "qcom,i2c-qup-v1.1.1";
				pinctrl-0 = <&i2c3_pins>;
				pinctrl-names = "default";
				reg = <0x16280000 0x1000>;
				interrupts = <GIC_SPI 151 IRQ_TYPE_NONE>;
				clocks = <&gcc GSBI3_QUP_CLK>,
					 <&gcc GSBI3_H_CLK>;
				clock-names = "core", "iface";
			};
		};

		gsbi6: gsbi@16500000 {
			status = "disabled";
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <6>;
			reg = <0x16500000 0x03>;
			clocks = <&gcc GSBI6_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			gsbi6_serial: serial@16540000 {
				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
				reg = <0x16540000 0x100>,
				      <0x16500000 0x03>;
				interrupts = <0 156 0x0>;
				clocks = <&gcc GSBI6_UART_CLK>, <&gcc GSBI6_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";
			};
		};

		gsbi7: gsbi@16600000 {
			status = "disabled";
			compatible = "qcom,gsbi-v1.0.0";
			cell-index = <7>;
			reg = <0x16600000 0x100>;
			clocks = <&gcc GSBI7_H_CLK>;
			clock-names = "iface";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;
			syscon-tcsr = <&tcsr>;

			gsbi7_serial: serial@16640000 {
				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
				reg = <0x16640000 0x1000>,
				      <0x16600000 0x1000>;
				interrupts = <0 158 0x0>;
				clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
				clock-names = "core", "iface";
				status = "disabled";
			};
		};

		qcom,ssbi@500000 {
			compatible = "qcom,ssbi";
			reg = <0x00500000 0x1000>;
			qcom,controller-type = "pmic-arbiter";

			pmicintc: pmic@0 {
				compatible = "qcom,pm8921";
				interrupt-parent = <&tlmm_pinmux>;
				interrupts = <74 8>;
				#interrupt-cells = <2>;
				interrupt-controller;
				#address-cells = <1>;
				#size-cells = <0>;

				pm8921_gpio: gpio@150 {

					compatible = "qcom,pm8921-gpio";
					reg = <0x150>;
					interrupts = <192 1>, <193 1>, <194 1>,
						     <195 1>, <196 1>, <197 1>,
						     <198 1>, <199 1>, <200 1>,
						     <201 1>, <202 1>, <203 1>,
						     <204 1>, <205 1>, <206 1>,
						     <207 1>, <208 1>, <209 1>,
						     <210 1>, <211 1>, <212 1>,
						     <213 1>, <214 1>, <215 1>,
						     <216 1>, <217 1>, <218 1>,
						     <219 1>, <220 1>, <221 1>,
						     <222 1>, <223 1>, <224 1>,
						     <225 1>, <226 1>, <227 1>,
						     <228 1>, <229 1>, <230 1>,
						     <231 1>, <232 1>, <233 1>,
						     <234 1>, <235 1>;

					gpio-controller;
					#gpio-cells = <2>;

				};

				pm8921_mpps: mpps@50 {
					compatible = "qcom,pm8921-mpp";
					reg = <0x50>;
					gpio-controller;
					#gpio-cells = <2>;
					interrupts =
					<128 1>, <129 1>, <130 1>, <131 1>,
					<132 1>, <133 1>, <134 1>, <135 1>,
					<136 1>, <137 1>, <138 1>, <139 1>;
				};

				rtc@11d {
					compatible = "qcom,pm8921-rtc";
					interrupt-parent = <&pmicintc>;
					interrupts = <39 1>;
					reg = <0x11d>;
					allow-set-time;
				};

				pwrkey@1c {
					compatible = "qcom,pm8921-pwrkey";
					reg = <0x1c>;
					interrupt-parent = <&pmicintc>;
					interrupts = <50 1>, <51 1>;
					debounce = <15625>;
					pull-up;
				};
			};
		};

		gcc: clock-controller@900000 {
			compatible = "qcom,gcc-apq8064";
			reg = <0x00900000 0x4000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
		};

		lcc: clock-controller@28000000 {
			compatible = "qcom,lcc-apq8064";
			reg = <0x28000000 0x1000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
		};

		mmcc: clock-controller@4000000 {
			compatible = "qcom,mmcc-apq8064";
			reg = <0x4000000 0x1000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
		};

		l2cc: clock-controller@2011000 {
			compatible	= "syscon";
			reg		= <0x2011000 0x1000>;
		};

		rpm@108000 {
			compatible	= "qcom,rpm-apq8064";
			reg		= <0x108000 0x1000>;
			qcom,ipc	= <&l2cc 0x8 2>;

			interrupts	= <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
					  <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
					  <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
			interrupt-names	= "ack", "err", "wakeup";

			regulators {
				compatible = "qcom,rpm-pm8921-regulators";

				pm8921_hdmi_switch: hdmi-switch {
					bias-pull-down;
				};
			};
		};

		usb1_phy: phy@12500000 {
			compatible	= "qcom,usb-otg-ci";
			reg		= <0x12500000 0x400>;
			interrupts	= <GIC_SPI 100 IRQ_TYPE_NONE>;
			status		= "disabled";
			dr_mode		= "host";

			clocks		= <&gcc USB_HS1_XCVR_CLK>,
					  <&gcc USB_HS1_H_CLK>;
			clock-names	= "core", "iface";

			resets		= <&gcc USB_HS1_RESET>;
			reset-names	= "link";
		};

		usb3_phy: phy@12520000 {
			compatible	= "qcom,usb-otg-ci";
			reg		= <0x12520000 0x400>;
			interrupts	= <GIC_SPI 188 IRQ_TYPE_NONE>;
			status		= "disabled";
			dr_mode		= "host";

			clocks		= <&gcc USB_HS3_XCVR_CLK>,
					  <&gcc USB_HS3_H_CLK>;
			clock-names	= "core", "iface";

			resets		= <&gcc USB_HS3_RESET>;
			reset-names	= "link";
		};

		usb4_phy: phy@12530000 {
			compatible	= "qcom,usb-otg-ci";
			reg		= <0x12530000 0x400>;
			interrupts	= <GIC_SPI 215 IRQ_TYPE_NONE>;
			status		= "disabled";
			dr_mode		= "host";

			clocks		= <&gcc USB_HS4_XCVR_CLK>,
					  <&gcc USB_HS4_H_CLK>;
			clock-names	= "core", "iface";

			resets		= <&gcc USB_HS4_RESET>;
			reset-names	= "link";
		};

		gadget1: gadget@12500000 {
			compatible	= "qcom,ci-hdrc";
			reg		= <0x12500000 0x400>;
			status		= "disabled";
			dr_mode		= "peripheral";
			interrupts	= <GIC_SPI 100 IRQ_TYPE_NONE>;
			usb-phy		= <&usb1_phy>;
		};

		usb1: usb@12500000 {
			compatible	= "qcom,ehci-host";
			reg		= <0x12500000 0x400>;
			interrupts	= <GIC_SPI 100 IRQ_TYPE_NONE>;
			status		= "disabled";
			usb-phy		= <&usb1_phy>;
		};

		usb3: usb@12520000 {
			compatible	= "qcom,ehci-host";
			reg		= <0x12520000 0x400>;
			interrupts	= <GIC_SPI 188 IRQ_TYPE_NONE>;
			status		= "disabled";
			usb-phy		= <&usb3_phy>;
		};

		usb4: usb@12530000 {
			compatible	= "qcom,ehci-host";
			reg		= <0x12530000 0x400>;
			interrupts	= <GIC_SPI 215 IRQ_TYPE_NONE>;
			status		= "disabled";
			usb-phy		= <&usb4_phy>;
		};

		sata_phy0: phy@1b400000 {
			compatible	= "qcom,apq8064-sata-phy";
			status		= "disabled";
			reg		= <0x1b400000 0x200>;
			reg-names	= "phy_mem";
			clocks		= <&gcc SATA_PHY_CFG_CLK>;
			clock-names	= "cfg";
			#phy-cells	= <0>;
		};

		sata0: sata@29000000 {
			compatible		= "generic-ahci";
			status			= "disabled";
			reg			= <0x29000000 0x180>;
			interrupts		= <GIC_SPI 209 IRQ_TYPE_NONE>;

			clocks			= <&gcc SFAB_SATA_S_H_CLK>,
						<&gcc SATA_H_CLK>,
						<&gcc SATA_A_CLK>,
						<&gcc SATA_RXOOB_CLK>,
						<&gcc SATA_PMALIVE_CLK>;
			clock-names		= "slave_iface",
						"iface",
						"bus",
						"rxoob",
						"core_pmalive";

			assigned-clocks		= <&gcc SATA_RXOOB_CLK>,
						<&gcc SATA_PMALIVE_CLK>;
			assigned-clock-rates	= <100000000>, <100000000>;

			phys			= <&sata_phy0>;
			phy-names		= "sata-phy";
		};

		/* Temporary fixed regulator */
		sdcc1bam:dma@12402000{
			compatible = "qcom,bam-v1.3.0";
			reg = <0x12402000 0x8000>;
			interrupts = <0 98 0>;
			clocks = <&gcc SDC1_H_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
		};

		sdcc3bam:dma@12182000{
			compatible = "qcom,bam-v1.3.0";
			reg = <0x12182000 0x8000>;
			interrupts = <0 96 0>;
			clocks = <&gcc SDC3_H_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
		};

		sdcc4bam:dma@121c2000{
			compatible = "qcom,bam-v1.3.0";
			reg = <0x121c2000 0x8000>;
			interrupts = <0 95 0>;
			clocks = <&gcc SDC4_H_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
		};

		amba {
			compatible = "arm,amba-bus";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;
			sdcc1: sdcc@12400000 {
				status		= "disabled";
				compatible	= "arm,pl18x", "arm,primecell";
				arm,primecell-periphid = <0x00051180>;
				reg		= <0x12400000 0x2000>;
				interrupts	= <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
				interrupt-names	= "cmd_irq";
				clocks		= <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
				clock-names	= "mclk", "apb_pclk";
				bus-width	= <8>;
				max-frequency	= <96000000>;
				non-removable;
				cap-sd-highspeed;
				cap-mmc-highspeed;
				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
				dma-names = "tx", "rx";
			};

			sdcc3: sdcc@12180000 {
				compatible	= "arm,pl18x", "arm,primecell";
				arm,primecell-periphid = <0x00051180>;
				status		= "disabled";
				reg		= <0x12180000 0x2000>;
				interrupts	= <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
				interrupt-names	= "cmd_irq";
				clocks		= <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
				clock-names	= "mclk", "apb_pclk";
				bus-width	= <4>;
				cap-sd-highspeed;
				cap-mmc-highspeed;
				max-frequency	= <192000000>;
				no-1-8-v;
				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
				dma-names = "tx", "rx";
			};

			sdcc4: sdcc@121c0000 {
				compatible	= "arm,pl18x", "arm,primecell";
				arm,primecell-periphid = <0x00051180>;
				status		= "disabled";
				reg		= <0x121c0000 0x2000>;
				interrupts	= <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
				interrupt-names	= "cmd_irq";
				clocks		= <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
				clock-names	= "mclk", "apb_pclk";
				bus-width	= <4>;
				cap-sd-highspeed;
				cap-mmc-highspeed;
				max-frequency	= <48000000>;
				dmas = <&sdcc4bam 2>, <&sdcc4bam 1>;
				dma-names = "tx", "rx";
				pinctrl-names = "default";
				pinctrl-0 = <&sdc4_gpios>;
			};
		};

		tcsr: syscon@1a400000 {
			compatible = "qcom,tcsr-apq8064", "syscon";
			reg = <0x1a400000 0x100>;
		};
	};
};