arch/arm/plat-omap/include/mach/entry-macro.S

/*
 * arch/arm/plat-omap/include/mach/entry-macro.S
 *
 * Low-level IRQ helper macros for OMAP-based platforms
 *
 * Copyright (C) 2009 Texas Instruments
 * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
 *
 * This file is licensed under  the terms of the GNU General Public
 * License version 2. This program is licensed "as is" without any
 * warranty of any kind, whether express or implied.
 */
#include <mach/hardware.h>
#include <mach/io.h>
#include <mach/irqs.h>
#include <asm/hardware/gic.h>

#if defined(CONFIG_ARCH_OMAP1)

#if (defined(CONFIG_ARCH_OMAP730)||defined(CONFIG_ARCH_OMAP850)) && \
	(defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX))
#error "FIXME: OMAP7XX doesn't support multiple-OMAP"
#elif defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
#define INT_IH2_IRQ		INT_7XX_IH2_IRQ
#elif defined(CONFIG_ARCH_OMAP15XX)
#define INT_IH2_IRQ		INT_1510_IH2_IRQ
#elif defined(CONFIG_ARCH_OMAP16XX)
#define INT_IH2_IRQ		INT_1610_IH2_IRQ
#else
#warning "IH2 IRQ defaulted"
#define INT_IH2_IRQ		INT_1510_IH2_IRQ
#endif

 		.macro	disable_fiq
		.endm

		.macro  get_irqnr_preamble, base, tmp
		.endm

		.macro  arch_ret_to_user, tmp1, tmp2
		.endm

		.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
		ldr	\base, =OMAP1_IO_ADDRESS(OMAP_IH1_BASE)
		ldr	\irqnr, [\base, #IRQ_ITR_REG_OFFSET]
		ldr	\tmp, [\base, #IRQ_MIR_REG_OFFSET]
		mov	\irqstat, #0xffffffff
		bic	\tmp, \irqstat, \tmp
		tst	\irqnr, \tmp
		beq	1510f

		ldr	\irqnr, [\base, #IRQ_SIR_FIQ_REG_OFFSET]
		cmp	\irqnr, #0
		ldreq	\irqnr, [\base, #IRQ_SIR_IRQ_REG_OFFSET]
		cmpeq	\irqnr, #INT_IH2_IRQ
		ldreq	\base, =OMAP1_IO_ADDRESS(OMAP_IH2_BASE)
		ldreq	\irqnr, [\base, #IRQ_SIR_IRQ_REG_OFFSET]
		addeqs	\irqnr, \irqnr, #32
1510:
		.endm

#endif
#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
			defined(CONFIG_ARCH_OMAP4)

#include <mach/omap24xx.h>
#include <mach/omap34xx.h>

/* REVISIT: This should be set dynamically if CONFIG_MULTI_OMAP2 is selected */
#if defined(CONFIG_ARCH_OMAP2420) || defined(CONFIG_ARCH_OMAP2430)
#define OMAP2_VA_IC_BASE		OMAP2_IO_ADDRESS(OMAP24XX_IC_BASE)
#elif defined(CONFIG_ARCH_OMAP34XX)
#define OMAP2_VA_IC_BASE		OMAP2_IO_ADDRESS(OMAP34XX_IC_BASE)
#endif
#if defined(CONFIG_ARCH_OMAP4)
#include <mach/omap44xx.h>
#endif
#define INTCPS_SIR_IRQ_OFFSET	0x0040		/* Active interrupt offset */
#define	ACTIVEIRQ_MASK		0x7f		/* Active interrupt bits */

		.macro	disable_fiq
		.endm

		.macro  get_irqnr_preamble, base, tmp
		.endm

		.macro  arch_ret_to_user, tmp1, tmp2
		.endm

#ifndef CONFIG_ARCH_OMAP4
		.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
		ldr	\base, =OMAP2_VA_IC_BASE
		ldr	\irqnr, [\base, #0x98] /* IRQ pending reg 1 */
		cmp	\irqnr, #0x0
		bne	2222f
		ldr	\irqnr, [\base, #0xb8] /* IRQ pending reg 2 */
		cmp	\irqnr, #0x0
		bne	2222f
		ldr	\irqnr, [\base, #0xd8] /* IRQ pending reg 3 */
		cmp	\irqnr, #0x0
2222:
		ldrne	\irqnr, [\base, #INTCPS_SIR_IRQ_OFFSET]
		and	\irqnr, \irqnr, #ACTIVEIRQ_MASK /* Clear spurious bits */

		.endm
#else
#define OMAP44XX_VA_GIC_CPU_BASE	OMAP2_IO_ADDRESS(OMAP44XX_GIC_CPU_BASE)

		/*
		 * The interrupt numbering scheme is defined in the
		 * interrupt controller spec.  To wit:
		 *
		 * Interrupts 0-15 are IPI
		 * 16-28 are reserved
		 * 29-31 are local.  We allow 30 to be used for the watchdog.
		 * 32-1020 are global
		 * 1021-1022 are reserved
		 * 1023 is "spurious" (no interrupt)
		 *
		 * For now, we ignore all local interrupts so only return an
		 * interrupt if it's between 30 and 1020.  The test_for_ipi
		 * routine below will pick up on IPIs.
		 * A simple read from the controller will tell us the number
		 * of the highest priority enabled interrupt.
		 * We then just need to check whether it is in the
		 * valid range for an IRQ (30-1020 inclusive).
		 */
		.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
		ldr     \base, =OMAP44XX_VA_GIC_CPU_BASE
		ldr     \irqstat, [\base, #GIC_CPU_INTACK]

		ldr     \tmp, =1021

		bic     \irqnr, \irqstat, #0x1c00

		cmp     \irqnr, #29
		cmpcc   \irqnr, \irqnr
		cmpne   \irqnr, \tmp
		cmpcs   \irqnr, \irqnr
		.endm

		/* We assume that irqstat (the raw value of the IRQ acknowledge
		 * register) is preserved from the macro above.
		 * If there is an IPI, we immediately signal end of interrupt
		 * on the controller, since this requires the original irqstat
		 * value which we won't easily be able to recreate later.
		 */

		.macro test_for_ipi, irqnr, irqstat, base, tmp
		bic	\irqnr, \irqstat, #0x1c00
		cmp	\irqnr, #16
		it	cc
		strcc	\irqstat, [\base, #GIC_CPU_EOI]
		it	cs
		cmpcs	\irqnr, \irqnr
		.endm

		/* As above, this assumes that irqstat and base are preserved */

		.macro test_for_ltirq, irqnr, irqstat, base, tmp
		bic	\irqnr, \irqstat, #0x1c00
		mov 	\tmp, #0
		cmp	\irqnr, #29
		itt	eq
		moveq	\tmp, #1
		streq	\irqstat, [\base, #GIC_CPU_EOI]
		cmp	\tmp, #0
		.endm
#endif

		.macro	irq_prio_table
		.endm

#endif