blob: 7b832c727f873b6964b1faa1c121a73796b113e4 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001#
2# Network device configuration
3#
4
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07005menuconfig NETDEVICES
Paolo 'Blaisorblade' Giarrussoce2d2ae2006-01-18 17:42:59 -08006 default y if UML
Jan Engelhardte0009822007-07-21 19:11:35 -07007 depends on NET
Linus Torvalds1da177e2005-04-16 15:20:36 -07008 bool "Network device support"
9 ---help---
10 You can say N here if you don't intend to connect your Linux box to
11 any other computer at all.
12
13 You'll have to say Y if your computer contains a network card that
14 you want to use under Linux. If you are going to run SLIP or PPP over
15 telephone line or null modem cable you need say Y here. Connecting
16 two machines with parallel ports using PLIP needs this, as well as
17 AX.25/KISS for sending Internet traffic over amateur radio links.
18
19 See also "The Linux Network Administrator's Guide" by Olaf Kirch and
20 Terry Dawson. Available at <http://www.tldp.org/guides.html>.
21
22 If unsure, say Y.
23
Randy Dunlap1618cb02006-09-25 23:11:21 -070024# All the following symbols are dependent on NETDEVICES - do not repeat
25# that for each of the symbols.
26if NETDEVICES
Randy Dunlapcbcd2a42005-07-27 13:04:35 -070027
Jamal Hadi Salim253af422006-01-08 22:34:25 -080028config IFB
29 tristate "Intermediate Functional Block support"
30 depends on NET_CLS_ACT
31 ---help---
Matt LaPlante3cb2fcc2006-11-30 05:22:59 +010032 This is an intermediate driver that allows sharing of
Jamal Hadi Salim253af422006-01-08 22:34:25 -080033 resources.
34 To compile this driver as a module, choose M here: the module
35 will be called ifb. If you want to use more than one ifb
36 device at a time, you need to compile this driver as a module.
37 Instead of 'ifb', the devices will then be called 'ifb0',
38 'ifb1' etc.
39 Look at the iproute2 documentation directory for usage etc
40
Linus Torvalds1da177e2005-04-16 15:20:36 -070041config DUMMY
42 tristate "Dummy net driver support"
Linus Torvalds1da177e2005-04-16 15:20:36 -070043 ---help---
44 This is essentially a bit-bucket device (i.e. traffic you send to
45 this device is consigned into oblivion) with a configurable IP
46 address. It is most commonly used in order to make your currently
47 inactive SLIP address seem like a real address for local programs.
48 If you use SLIP or PPP, you might want to say Y here. Since this
49 thing often comes in handy, the default is Y. It won't enlarge your
50 kernel either. What a deal. Read about it in the Network
51 Administrator's Guide, available from
52 <http://www.tldp.org/docs.html#guide>.
53
54 To compile this driver as a module, choose M here: the module
55 will be called dummy. If you want to use more than one dummy
56 device at a time, you need to compile this driver as a module.
57 Instead of 'dummy', the devices will then be called 'dummy0',
58 'dummy1' etc.
59
60config BONDING
61 tristate "Bonding driver support"
Linus Torvalds1da177e2005-04-16 15:20:36 -070062 depends on INET
Brian Haley305d5522008-11-04 17:51:14 -080063 depends on IPV6 || IPV6=n
Linus Torvalds1da177e2005-04-16 15:20:36 -070064 ---help---
65 Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
66 Channels together. This is called 'Etherchannel' by Cisco,
67 'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.
68
69 The driver supports multiple bonding modes to allow for both high
Jon Mason47c51432006-02-12 11:53:04 -060070 performance and high availability operation.
Linus Torvalds1da177e2005-04-16 15:20:36 -070071
72 Refer to <file:Documentation/networking/bonding.txt> for more
73 information.
74
75 To compile this driver as a module, choose M here: the module
76 will be called bonding.
77
Patrick McHardyb863ceb2007-07-14 18:55:06 -070078config MACVLAN
79 tristate "MAC-VLAN support (EXPERIMENTAL)"
80 depends on EXPERIMENTAL
81 ---help---
82 This allows one to create virtual interfaces that map packets to
83 or from specific MAC addresses to a particular interface.
84
Patrick McHardy3dbf8d52008-02-26 17:52:05 -080085 Macvlan devices can be added using the "ip" command from the
86 iproute2 package starting with the iproute2-2.6.23 release:
87
88 "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"
89
Patrick McHardyb863ceb2007-07-14 18:55:06 -070090 To compile this driver as a module, choose M here: the module
91 will be called macvlan.
92
Arnd Bergmann20d29d72010-01-30 12:24:26 +000093config MACVTAP
94 tristate "MAC-VLAN based tap driver (EXPERIMENTAL)"
95 depends on MACVLAN
96 help
97 This adds a specialized tap character device driver that is based
98 on the MAC-VLAN network interface, called macvtap. A macvtap device
99 can be added in the same way as a macvlan device, using 'type
100 macvlan', and then be accessed through the tap user space interface.
101
102 To compile this driver as a module, choose M here: the module
103 will be called macvtap.
104
Linus Torvalds1da177e2005-04-16 15:20:36 -0700105config EQUALIZER
106 tristate "EQL (serial line load balancing) support"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700107 ---help---
108 If you have two serial connections to some other computer (this
109 usually requires two modems and two telephone lines) and you use
110 SLIP (the protocol for sending Internet traffic over telephone
111 lines) or PPP (a better SLIP) on them, you can make them behave like
112 one double speed connection using this driver. Naturally, this has
113 to be supported at the other end as well, either with a similar EQL
114 Linux driver or with a Livingston Portmaster 2e.
115
116 Say Y if you want this and read
117 <file:Documentation/networking/eql.txt>. You may also want to read
118 section 6.2 of the NET-3-HOWTO, available from
119 <http://www.tldp.org/docs.html#howto>.
120
121 To compile this driver as a module, choose M here: the module
122 will be called eql. If unsure, say N.
123
124config TUN
125 tristate "Universal TUN/TAP device driver support"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700126 select CRC32
127 ---help---
128 TUN/TAP provides packet reception and transmission for user space
129 programs. It can be viewed as a simple Point-to-Point or Ethernet
130 device, which instead of receiving packets from a physical media,
131 receives them from user space program and instead of sending packets
132 via physical media writes them to the user space program.
133
134 When a program opens /dev/net/tun, driver creates and registers
135 corresponding net device tunX or tapX. After a program closed above
136 devices, driver will automatically delete tunXX or tapXX device and
137 all routes corresponding to it.
138
139 Please read <file:Documentation/networking/tuntap.txt> for more
140 information.
141
142 To compile this driver as a module, choose M here: the module
143 will be called tun.
144
145 If you don't know what to use this for, you don't need it.
146
Pavel Emelyanove314dbd2007-09-25 16:14:46 -0700147config VETH
Rusty Russell6a9a0252007-11-06 20:35:55 -0800148 tristate "Virtual ethernet pair device"
Pavel Emelyanove314dbd2007-09-25 16:14:46 -0700149 ---help---
Rusty Russell6a9a0252007-11-06 20:35:55 -0800150 This device is a local ethernet tunnel. Devices are created in pairs.
151 When one end receives the packet it appears on its pair and vice
152 versa.
Pavel Emelyanove314dbd2007-09-25 16:14:46 -0700153
Linus Torvalds1da177e2005-04-16 15:20:36 -0700154config NET_SB1000
155 tristate "General Instruments Surfboard 1000"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -0700156 depends on PNP
Linus Torvalds1da177e2005-04-16 15:20:36 -0700157 ---help---
158 This is a driver for the General Instrument (also known as
159 NextLevel) SURFboard 1000 internal
160 cable modem. This is an ISA card which is used by a number of cable
161 TV companies to provide cable modem access. It's a one-way
162 downstream-only cable modem, meaning that your upstream net link is
163 provided by your regular phone modem.
164
165 At present this driver only compiles as a module, so say M here if
166 you have this card. The module will be called sb1000. Then read
167 <file:Documentation/networking/README.sb1000> for information on how
168 to use this module, as it needs special ppp scripts for establishing
169 a connection. Further documentation and the necessary scripts can be
170 found at:
171
172 <http://www.jacksonville.net/~fventuri/>
173 <http://home.adelphia.net/~siglercm/sb1000.html>
174 <http://linuxpower.cx/~cable/>
175
176 If you don't have this card, of course say N.
177
Adrian Bunkf65fd8f2006-01-05 22:45:41 -0800178source "drivers/net/arcnet/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700179
Andy Fleming00db8182005-07-30 19:31:23 -0400180source "drivers/net/phy/Kconfig"
181
Linus Torvalds1da177e2005-04-16 15:20:36 -0700182#
183# Ethernet
184#
185
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700186menuconfig NET_ETHERNET
Linus Torvalds1da177e2005-04-16 15:20:36 -0700187 bool "Ethernet (10 or 100Mbit)"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700188 depends on !UML
Linus Torvalds1da177e2005-04-16 15:20:36 -0700189 ---help---
190 Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
191 type of Local Area Network (LAN) in universities and companies.
192
193 Common varieties of Ethernet are: 10BASE-2 or Thinnet (10 Mbps over
194 coaxial cable, linking computers in a chain), 10BASE-T or twisted
195 pair (10 Mbps over twisted pair cable, linking computers to central
196 hubs), 10BASE-F (10 Mbps over optical fiber links, using hubs),
197 100BASE-TX (100 Mbps over two twisted pair cables, using hubs),
198 100BASE-T4 (100 Mbps over 4 standard voice-grade twisted pair
199 cables, using hubs), 100BASE-FX (100 Mbps over optical fiber links)
200 [the 100BASE varieties are also known as Fast Ethernet], and Gigabit
201 Ethernet (1 Gbps over optical fiber or short copper links).
202
203 If your Linux machine will be connected to an Ethernet and you have
204 an Ethernet network interface card (NIC) installed in your computer,
205 say Y here and read the Ethernet-HOWTO, available from
206 <http://www.tldp.org/docs.html#howto>. You will then also have
207 to say Y to the driver for your particular NIC.
208
209 Note that the answer to this question won't directly affect the
210 kernel: saying N will just cause the configurator to skip all
211 the questions about Ethernet network cards. If unsure, say N.
212
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700213if NET_ETHERNET
214
Linus Torvalds1da177e2005-04-16 15:20:36 -0700215config MII
216 tristate "Generic Media Independent Interface device support"
Linus Torvalds1da177e2005-04-16 15:20:36 -0700217 help
218 Most ethernet controllers have MII transceiver either as an external
219 or internal device. It is safe to say Y or M here even if your
220 ethernet card lack MII.
221
Haavard Skinnemoen89e57852006-11-09 14:51:17 +0100222config MACB
223 tristate "Atmel MACB support"
Nicolas Ferre789b23b2009-06-26 15:36:58 +0100224 depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91SAM9G45 || ARCH_AT91CAP9
frederic RODO6c36a702007-07-12 19:07:24 +0200225 select PHYLIB
Haavard Skinnemoen89e57852006-11-09 14:51:17 +0100226 help
227 The Atmel MACB ethernet interface is found on many AT32 and AT91
228 parts. Say Y to include support for the MACB chip.
229
230 To compile this driver as a module, choose M here: the module
231 will be called macb.
232
Linus Torvalds1da177e2005-04-16 15:20:36 -0700233source "drivers/net/arm/Kconfig"
234
Ben Dooks825a2ff2007-07-03 16:53:09 +0100235config AX88796
236 tristate "ASIX AX88796 NE2000 clone support"
Magnus Damm86879912007-11-08 16:31:05 +0900237 depends on ARM || MIPS || SUPERH
Ben Dooks825a2ff2007-07-03 16:53:09 +0100238 select CRC32
239 select MII
240 help
241 AX88796 driver, using platform bus to provide
242 chip detection and resources
243
Magnus Damm89e536a2007-09-28 22:42:16 -0700244config AX88796_93CX6
245 bool "ASIX AX88796 external 93CX6 eeprom support"
246 depends on AX88796
247 select EEPROM_93CX6
248 help
249 Select this if your platform comes with an external 93CX6 eeprom.
250
Linus Torvalds1da177e2005-04-16 15:20:36 -0700251config MACE
252 tristate "MACE (Power Mac ethernet) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700253 depends on PPC_PMAC && PPC32
Linus Torvalds1da177e2005-04-16 15:20:36 -0700254 select CRC32
255 help
256 Power Macintoshes and clones with Ethernet built-in on the
257 motherboard will usually use a MACE (Medium Access Control for
258 Ethernet) interface. Say Y to include support for the MACE chip.
259
260 To compile this driver as a module, choose M here: the module
261 will be called mace.
262
263config MACE_AAUI_PORT
264 bool "Use AAUI port instead of TP by default"
265 depends on MACE
266 help
267 Some Apple machines (notably the Apple Network Server) which use the
268 MACE ethernet chip have an Apple AUI port (small 15-pin connector),
269 instead of an 8-pin RJ45 connector for twisted-pair ethernet. Say
270 Y here if you have such a machine. If unsure, say N.
271 The driver will default to AAUI on ANS anyway, and if you use it as
272 a module, you can provide the port_aaui=0|1 to force the driver.
273
274config BMAC
275 tristate "BMAC (G3 ethernet) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700276 depends on PPC_PMAC && PPC32
Linus Torvalds1da177e2005-04-16 15:20:36 -0700277 select CRC32
278 help
279 Say Y for support of BMAC Ethernet interfaces. These are used on G3
280 computers.
281
282 To compile this driver as a module, choose M here: the module
283 will be called bmac.
284
Linus Torvalds1da177e2005-04-16 15:20:36 -0700285config ARIADNE
286 tristate "Ariadne support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700287 depends on ZORRO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700288 help
289 If you have a Village Tronic Ariadne Ethernet adapter, say Y.
290 Otherwise, say N.
291
292 To compile this driver as a module, choose M here: the module
293 will be called ariadne.
294
295config A2065
296 tristate "A2065 support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700297 depends on ZORRO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700298 select CRC32
299 help
300 If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise,
301 say N.
302
303 To compile this driver as a module, choose M here: the module
304 will be called a2065.
305
306config HYDRA
307 tristate "Hydra support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700308 depends on ZORRO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700309 select CRC32
310 help
311 If you have a Hydra Ethernet adapter, say Y. Otherwise, say N.
312
313 To compile this driver as a module, choose M here: the module
314 will be called hydra.
315
316config ZORRO8390
317 tristate "Zorro NS8390-based Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700318 depends on ZORRO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700319 select CRC32
320 help
321 This driver is for Zorro Ethernet cards using an NS8390-compatible
322 chipset, like the Village Tronic Ariadne II and the Individual
323 Computers X-Surf Ethernet cards. If you have such a card, say Y.
324 Otherwise, say N.
325
326 To compile this driver as a module, choose M here: the module
327 will be called zorro8390.
328
329config APNE
330 tristate "PCMCIA NE2000 support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700331 depends on AMIGA_PCMCIA
Linus Torvalds1da177e2005-04-16 15:20:36 -0700332 select CRC32
333 help
334 If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise,
335 say N.
336
337 To compile this driver as a module, choose M here: the module
338 will be called apne.
339
Linus Torvalds1da177e2005-04-16 15:20:36 -0700340config MAC8390
341 bool "Macintosh NS 8390 based ethernet cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700342 depends on MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700343 select CRC32
344 help
345 If you want to include a driver to support Nubus or LC-PDS
346 Ethernet cards using an NS8390 chipset or its equivalent, say Y
347 and read the Ethernet-HOWTO, available from
348 <http://www.tldp.org/docs.html#howto>.
349
350config MAC89x0
351 tristate "Macintosh CS89x0 based ethernet cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700352 depends on MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700353 ---help---
354 Support for CS89x0 chipset based Ethernet cards. If you have a
355 Nubus or LC-PDS network (Ethernet) card of this type, say Y and
356 read the Ethernet-HOWTO, available from
357 <http://www.tldp.org/docs.html#howto>.
358
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800359 To compile this driver as a module, choose M here. This module will
Linus Torvalds1da177e2005-04-16 15:20:36 -0700360 be called mac89x0.
361
362config MACSONIC
363 tristate "Macintosh SONIC based ethernet (onboard, NuBus, LC, CS)"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700364 depends on MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700365 ---help---
366 Support for NatSemi SONIC based Ethernet devices. This includes
367 the onboard Ethernet in many Quadras as well as some LC-PDS,
368 a few Nubus and all known Comm Slot Ethernet cards. If you have
369 one of these say Y and read the Ethernet-HOWTO, available from
370 <http://www.tldp.org/docs.html#howto>.
371
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800372 To compile this driver as a module, choose M here. This module will
Linus Torvalds1da177e2005-04-16 15:20:36 -0700373 be called macsonic.
374
375config MACMACE
Finn Thain8b6aaab2007-05-01 22:33:01 +0200376 bool "Macintosh (AV) onboard MACE ethernet"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700377 depends on MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700378 select CRC32
379 help
380 Support for the onboard AMD 79C940 MACE Ethernet controller used in
381 the 660AV and 840AV Macintosh. If you have one of these Macintoshes
382 say Y and read the Ethernet-HOWTO, available from
383 <http://www.tldp.org/docs.html#howto>.
384
385config MVME147_NET
386 tristate "MVME147 (Lance) Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700387 depends on MVME147
Linus Torvalds1da177e2005-04-16 15:20:36 -0700388 select CRC32
389 help
390 Support for the on-board Ethernet interface on the Motorola MVME147
391 single-board computer. Say Y here to include the
392 driver for this chip in your kernel.
393 To compile this driver as a module, choose M here.
394
395config MVME16x_NET
396 tristate "MVME16x Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700397 depends on MVME16x
Linus Torvalds1da177e2005-04-16 15:20:36 -0700398 help
399 This is the driver for the Ethernet interface on the Motorola
400 MVME162, 166, 167, 172 and 177 boards. Say Y here to include the
401 driver for this chip in your kernel.
402 To compile this driver as a module, choose M here.
403
404config BVME6000_NET
405 tristate "BVME6000 Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700406 depends on BVME6000
Linus Torvalds1da177e2005-04-16 15:20:36 -0700407 help
408 This is the driver for the Ethernet interface on BVME4000 and
409 BVME6000 VME boards. Say Y here to include the driver for this chip
410 in your kernel.
411 To compile this driver as a module, choose M here.
412
413config ATARILANCE
414 tristate "Atari Lance support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700415 depends on ATARI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700416 help
417 Say Y to include support for several Atari Ethernet adapters based
418 on the AMD Lance chipset: RieblCard (with or without battery), or
419 PAMCard VME (also the version by Rhotron, with different addresses).
420
Linus Torvalds1da177e2005-04-16 15:20:36 -0700421config SUN3LANCE
422 tristate "Sun3/Sun3x on-board LANCE support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700423 depends on SUN3 || SUN3X
Linus Torvalds1da177e2005-04-16 15:20:36 -0700424 help
425 Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80)
426 featured an AMD Lance 10Mbit Ethernet controller on board; say Y
427 here to compile in the Linux driver for this and enable Ethernet.
428 General Linux information on the Sun 3 and 3x series (now
429 discontinued) is at
430 <http://www.angelfire.com/ca2/tech68k/sun3.html>.
431
432 If you're not building a kernel for a Sun 3, say N.
433
434config SUN3_82586
Al Viro9a482202005-08-25 06:24:56 +0100435 bool "Sun3 on-board Intel 82586 support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700436 depends on SUN3
Linus Torvalds1da177e2005-04-16 15:20:36 -0700437 help
438 This driver enables support for the on-board Intel 82586 based
439 Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards. Note
440 that this driver does not support 82586-based adapters on additional
441 VME boards.
442
443config HPLANCE
444 bool "HP on-board LANCE support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700445 depends on DIO
Linus Torvalds1da177e2005-04-16 15:20:36 -0700446 select CRC32
447 help
448 If you want to use the builtin "LANCE" Ethernet controller on an
449 HP300 machine, say Y here.
450
451config LASI_82596
452 tristate "Lasi ethernet"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700453 depends on GSC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700454 help
Matthew Wilcox6de187e2006-11-18 10:05:16 -0700455 Say Y here to support the builtin Intel 82596 ethernet controller
456 found in Hewlett-Packard PA-RISC machines with 10Mbit ethernet.
Linus Torvalds1da177e2005-04-16 15:20:36 -0700457
Thomas Bogendoerferf2ec8032007-06-28 00:49:06 +0200458config SNI_82596
459 tristate "SNI RM ethernet"
460 depends on NET_ETHERNET && SNI_RM
461 help
462 Say Y here to support the on-board Intel 82596 ethernet controller
463 built into SNI RM machines.
464
Florian Fainellief112912008-03-19 17:14:51 +0100465config KORINA
466 tristate "Korina (IDT RC32434) Ethernet support"
Ralf Baechlef57b2062008-04-28 12:48:40 +0100467 depends on NET_ETHERNET && MIKROTIK_RB532
Florian Fainellief112912008-03-19 17:14:51 +0100468 help
469 If you have a Mikrotik RouterBoard 500 or IDT RC32434
470 based system say Y. Otherwise say N.
471
Linus Torvalds1da177e2005-04-16 15:20:36 -0700472config MIPS_JAZZ_SONIC
473 tristate "MIPS JAZZ onboard SONIC Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700474 depends on MACH_JAZZ
Linus Torvalds1da177e2005-04-16 15:20:36 -0700475 help
476 This is the driver for the onboard card of MIPS Magnum 4000,
477 Acer PICA, Olivetti M700-10 and a few other identical OEM systems.
478
Chris Zankel74f2a5f02008-05-05 23:36:35 -0700479config XTENSA_XT2000_SONIC
480 tristate "Xtensa XT2000 onboard SONIC Ethernet support"
481 depends on XTENSA_PLATFORM_XT2000
482 help
483 This is the driver for the onboard card of the Xtensa XT2000 board.
484
Linus Torvalds1da177e2005-04-16 15:20:36 -0700485config MIPS_AU1X00_ENET
486 bool "MIPS AU1000 Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700487 depends on SOC_AU1X00
Herbert Valerio Riedel0638dec2006-06-01 09:41:04 +0200488 select PHYLIB
Linus Torvalds1da177e2005-04-16 15:20:36 -0700489 select CRC32
490 help
491 If you have an Alchemy Semi AU1X00 based system
492 say Y. Otherwise, say N.
493
Linus Torvalds1da177e2005-04-16 15:20:36 -0700494config SGI_IOC3_ETH
495 bool "SGI IOC3 Ethernet"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700496 depends on PCI && SGI_IP27
Linus Torvalds1da177e2005-04-16 15:20:36 -0700497 select CRC32
498 select MII
499 help
500 If you have a network (Ethernet) card of this type, say Y and read
501 the Ethernet-HOWTO, available from
502 <http://www.tldp.org/docs.html#howto>.
503
Ralf Baechledcbf8472005-10-10 14:51:27 +0100504config MIPS_SIM_NET
Ralf Baechle1e2b9802007-03-18 23:21:22 +0000505 tristate "MIPS simulator Network device"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700506 depends on MIPS_SIM
Ralf Baechledcbf8472005-10-10 14:51:27 +0100507 help
508 The MIPSNET device is a simple Ethernet network device which is
509 emulated by the MIPS Simulator.
510 If you are not using a MIPSsim or are unsure, say N.
511
Linus Torvalds1da177e2005-04-16 15:20:36 -0700512config SGI_O2MACE_ETH
513 tristate "SGI O2 MACE Fast Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700514 depends on SGI_IP32=y
Linus Torvalds1da177e2005-04-16 15:20:36 -0700515
516config STNIC
517 tristate "National DP83902AV support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700518 depends on SUPERH
Linus Torvalds1da177e2005-04-16 15:20:36 -0700519 select CRC32
520 help
521 Support for cards based on the National Semiconductor DP83902AV
522 ST-NIC Serial Network Interface Controller for Twisted Pair. This
523 is a 10Mbit/sec Ethernet controller. Product overview and specs at
524 <http://www.national.com/pf/DP/DP83902A.html>.
525
526 If unsure, say N.
527
Nobuhiro Iwamatsu86a74ff2008-06-09 16:33:56 -0700528config SH_ETH
529 tristate "Renesas SuperH Ethernet support"
530 depends on SUPERH && \
Yoshihiro Shimoda65ac8852009-05-24 23:54:30 +0000531 (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || \
532 CPU_SUBTYPE_SH7763 || CPU_SUBTYPE_SH7619 || \
533 CPU_SUBTYPE_SH7724)
Nobuhiro Iwamatsu86a74ff2008-06-09 16:33:56 -0700534 select CRC32
535 select MII
536 select MDIO_BITBANG
537 select PHYLIB
538 help
539 Renesas SuperH Ethernet device driver.
Yoshihiro Shimoda65ac8852009-05-24 23:54:30 +0000540 This driver support SH7710, SH7712, SH7763, SH7619, and SH7724.
Nobuhiro Iwamatsu86a74ff2008-06-09 16:33:56 -0700541
Linus Torvalds1da177e2005-04-16 15:20:36 -0700542config SUNLANCE
543 tristate "Sun LANCE support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700544 depends on SBUS
Linus Torvalds1da177e2005-04-16 15:20:36 -0700545 select CRC32
546 help
547 This driver supports the "le" interface present on all 32-bit Sparc
548 systems, on some older Ultra systems and as an Sbus option. These
549 cards are based on the AMD Lance chipset, which is better known
550 via the NE2100 cards.
551
552 To compile this driver as a module, choose M here: the module
553 will be called sunlance.
554
555config HAPPYMEAL
556 tristate "Sun Happy Meal 10/100baseT support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700557 depends on SBUS || PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700558 select CRC32
559 help
560 This driver supports the "hme" interface present on most Ultra
561 systems and as an option on older Sbus systems. This driver supports
562 both PCI and Sbus devices. This driver also supports the "qfe" quad
563 100baseT device available in both PCI and Sbus configurations.
564
565 To compile this driver as a module, choose M here: the module
566 will be called sunhme.
567
568config SUNBMAC
569 tristate "Sun BigMAC 10/100baseT support (EXPERIMENTAL)"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700570 depends on SBUS && EXPERIMENTAL
Linus Torvalds1da177e2005-04-16 15:20:36 -0700571 select CRC32
572 help
573 This driver supports the "be" interface available as an Sbus option.
574 This is Sun's older 100baseT Ethernet device.
575
576 To compile this driver as a module, choose M here: the module
577 will be called sunbmac.
578
579config SUNQE
580 tristate "Sun QuadEthernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700581 depends on SBUS
Linus Torvalds1da177e2005-04-16 15:20:36 -0700582 select CRC32
583 help
584 This driver supports the "qe" 10baseT Ethernet device, available as
585 an Sbus option. Note that this is not the same as Quad FastEthernet
586 "qfe" which is supported by the Happy Meal driver instead.
587
588 To compile this driver as a module, choose M here: the module
589 will be called sunqe.
590
591config SUNGEM
592 tristate "Sun GEM support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700593 depends on PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700594 select CRC32
595 help
596 Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0. See also
597 <http://www.sun.com/products-n-solutions/hardware/docs/pdf/806-3985-10.pdf>.
598
David S. Miller1f26dac2005-09-27 15:24:13 -0700599config CASSINI
600 tristate "Sun Cassini support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700601 depends on PCI
David S. Miller1f26dac2005-09-27 15:24:13 -0700602 select CRC32
603 help
604 Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also
605 <http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf>
606
David S. Miller4c521e42007-07-09 22:23:51 -0700607config SUNVNET
608 tristate "Sun Virtual Network support"
609 depends on SUN_LDOMS
610 help
611 Support for virtual network devices under Sun Logical Domains.
612
Linus Torvalds1da177e2005-04-16 15:20:36 -0700613config NET_VENDOR_3COM
614 bool "3COM cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700615 depends on ISA || EISA || MCA || PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700616 help
617 If you have a network (Ethernet) card belonging to this class, say Y
618 and read the Ethernet-HOWTO, available from
619 <http://www.tldp.org/docs.html#howto>.
620
621 Note that the answer to this question doesn't directly affect the
622 kernel: saying N will just cause the configurator to skip all
623 the questions about 3COM cards. If you say Y, you will be asked for
624 your specific card in the following questions.
625
626config EL1
627 tristate "3c501 \"EtherLink\" support"
628 depends on NET_VENDOR_3COM && ISA
629 ---help---
630 If you have a network (Ethernet) card of this type, say Y and read
631 the Ethernet-HOWTO, available from
632 <http://www.tldp.org/docs.html#howto>. Also, consider buying a
633 new card, since the 3c501 is slow, broken, and obsolete: you will
634 have problems. Some people suggest to ping ("man ping") a nearby
635 machine every minute ("man cron") when using this card.
636
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800637 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700638 will be called 3c501.
639
640config EL2
641 tristate "3c503 \"EtherLink II\" support"
642 depends on NET_VENDOR_3COM && ISA
643 select CRC32
644 help
645 If you have a network (Ethernet) card of this type, say Y and read
646 the Ethernet-HOWTO, available from
647 <http://www.tldp.org/docs.html#howto>.
648
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800649 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700650 will be called 3c503.
651
652config ELPLUS
653 tristate "3c505 \"EtherLink Plus\" support"
Al Viroa5532602005-05-04 05:39:42 +0100654 depends on NET_VENDOR_3COM && ISA && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -0700655 ---help---
656 Information about this network (Ethernet) card can be found in
657 <file:Documentation/networking/3c505.txt>. If you have a card of
658 this type, say Y and read the Ethernet-HOWTO, available from
659 <http://www.tldp.org/docs.html#howto>.
660
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800661 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700662 will be called 3c505.
663
664config EL16
665 tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)"
666 depends on NET_VENDOR_3COM && ISA && EXPERIMENTAL
667 help
668 If you have a network (Ethernet) card of this type, say Y and read
669 the Ethernet-HOWTO, available from
670 <http://www.tldp.org/docs.html#howto>.
671
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800672 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700673 will be called 3c507.
674
675config EL3
676 tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support"
677 depends on NET_VENDOR_3COM && (ISA || EISA || MCA)
678 ---help---
679 If you have a network (Ethernet) card belonging to the 3Com
680 EtherLinkIII series, say Y and read the Ethernet-HOWTO, available
681 from <http://www.tldp.org/docs.html#howto>.
682
683 If your card is not working you may need to use the DOS
684 setup disk to disable Plug & Play mode, and to select the default
685 media type.
686
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800687 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700688 will be called 3c509.
689
690config 3C515
691 tristate "3c515 ISA \"Fast EtherLink\""
Al Viroa5532602005-05-04 05:39:42 +0100692 depends on NET_VENDOR_3COM && (ISA || EISA) && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -0700693 help
694 If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet
695 network card, say Y and read the Ethernet-HOWTO, available from
696 <http://www.tldp.org/docs.html#howto>.
697
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800698 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700699 will be called 3c515.
700
701config ELMC
702 tristate "3c523 \"EtherLink/MC\" support"
703 depends on NET_VENDOR_3COM && MCA_LEGACY
704 help
705 If you have a network (Ethernet) card of this type, say Y and read
706 the Ethernet-HOWTO, available from
707 <http://www.tldp.org/docs.html#howto>.
708
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800709 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700710 will be called 3c523.
711
712config ELMC_II
713 tristate "3c527 \"EtherLink/MC 32\" support (EXPERIMENTAL)"
714 depends on NET_VENDOR_3COM && MCA && MCA_LEGACY
715 help
716 If you have a network (Ethernet) card of this type, say Y and read
717 the Ethernet-HOWTO, available from
718 <http://www.tldp.org/docs.html#howto>.
719
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800720 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700721 will be called 3c527.
722
723config VORTEX
724 tristate "3c590/3c900 series (592/595/597) \"Vortex/Boomerang\" support"
725 depends on NET_VENDOR_3COM && (PCI || EISA)
726 select MII
727 ---help---
Jon Mason47c51432006-02-12 11:53:04 -0600728 This option enables driver support for a large number of 10Mbps and
729 10/100Mbps EISA, PCI and PCMCIA 3Com network cards:
Linus Torvalds1da177e2005-04-16 15:20:36 -0700730
731 "Vortex" (Fast EtherLink 3c590/3c592/3c595/3c597) EISA and PCI
732 "Boomerang" (EtherLink XL 3c900 or 3c905) PCI
733 "Cyclone" (3c540/3c900/3c905/3c980/3c575/3c656) PCI and Cardbus
734 "Tornado" (3c905) PCI
735 "Hurricane" (3c555/3cSOHO) PCI
736
737 If you have such a card, say Y and read the Ethernet-HOWTO,
738 available from <http://www.tldp.org/docs.html#howto>. More
739 specific information is in
740 <file:Documentation/networking/vortex.txt> and in the comments at
741 the beginning of <file:drivers/net/3c59x.c>.
742
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800743 To compile this support as a module, choose M here.
Linus Torvalds1da177e2005-04-16 15:20:36 -0700744
745config TYPHOON
746 tristate "3cr990 series \"Typhoon\" support"
747 depends on NET_VENDOR_3COM && PCI
748 select CRC32
749 ---help---
750 This option enables driver support for the 3cr990 series of cards:
751
752 3C990-TX, 3CR990-TX-95, 3CR990-TX-97, 3CR990-FX-95, 3CR990-FX-97,
753 3CR990SVR, 3CR990SVR95, 3CR990SVR97, 3CR990-FX-95 Server,
754 3CR990-FX-97 Server, 3C990B-TX-M, 3C990BSVR
755
756 If you have a network (Ethernet) card of this type, say Y and read
757 the Ethernet-HOWTO, available from
758 <http://www.tldp.org/docs.html#howto>.
759
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800760 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700761 will be called typhoon.
762
763config LANCE
764 tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700765 depends on ISA && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -0700766 help
767 If you have a network (Ethernet) card of this type, say Y and read
768 the Ethernet-HOWTO, available from
769 <http://www.tldp.org/docs.html#howto>. Some LinkSys cards are
770 of this type.
771
772 To compile this driver as a module, choose M here: the module
773 will be called lance. This is recommended.
774
775config NET_VENDOR_SMC
776 bool "Western Digital/SMC cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700777 depends on ISA || MCA || EISA || MAC
Linus Torvalds1da177e2005-04-16 15:20:36 -0700778 help
779 If you have a network (Ethernet) card belonging to this class, say Y
780 and read the Ethernet-HOWTO, available from
781 <http://www.tldp.org/docs.html#howto>.
782
783 Note that the answer to this question doesn't directly affect the
784 kernel: saying N will just cause the configurator to skip all
785 the questions about Western Digital cards. If you say Y, you will be
786 asked for your specific card in the following questions.
787
788config WD80x3
789 tristate "WD80*3 support"
790 depends on NET_VENDOR_SMC && ISA
791 select CRC32
792 help
793 If you have a network (Ethernet) card of this type, say Y and read
794 the Ethernet-HOWTO, available from
795 <http://www.tldp.org/docs.html#howto>.
796
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800797 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700798 will be called wd.
799
800config ULTRAMCA
801 tristate "SMC Ultra MCA support"
802 depends on NET_VENDOR_SMC && MCA
803 select CRC32
804 help
805 If you have a network (Ethernet) card of this type and are running
806 an MCA based system (PS/2), say Y and read the Ethernet-HOWTO,
807 available from <http://www.tldp.org/docs.html#howto>.
808
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800809 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700810 will be called smc-mca.
811
812config ULTRA
813 tristate "SMC Ultra support"
814 depends on NET_VENDOR_SMC && ISA
815 select CRC32
816 ---help---
817 If you have a network (Ethernet) card of this type, say Y and read
818 the Ethernet-HOWTO, available from
819 <http://www.tldp.org/docs.html#howto>.
820
821 Important: There have been many reports that, with some motherboards
822 mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible,
823 such as some BusLogic models) causes corruption problems with many
824 operating systems. The Linux smc-ultra driver has a work-around for
825 this but keep it in mind if you have such a SCSI card and have
826 problems.
827
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800828 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700829 will be called smc-ultra.
830
831config ULTRA32
832 tristate "SMC Ultra32 EISA support"
833 depends on NET_VENDOR_SMC && EISA
834 select CRC32
835 help
836 If you have a network (Ethernet) card of this type, say Y and read
837 the Ethernet-HOWTO, available from
838 <http://www.tldp.org/docs.html#howto>.
839
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800840 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700841 will be called smc-ultra32.
842
Bryan Wue190d6b2007-07-17 14:43:44 +0800843config BFIN_MAC
Mike Frysinger736783b2008-08-27 11:47:57 +0800844 tristate "Blackfin on-chip MAC support"
Sonic Zhang33a2a2b2009-01-08 10:52:26 -0800845 depends on NET_ETHERNET && (BF516 || BF518 || BF526 || BF527 || BF536 || BF537)
Bryan Wue190d6b2007-07-17 14:43:44 +0800846 select CRC32
Bryan Wueeb70af2007-09-19 23:37:41 +0800847 select MII
848 select PHYLIB
Bryan Wue190d6b2007-07-17 14:43:44 +0800849 select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
850 help
Mike Frysinger736783b2008-08-27 11:47:57 +0800851 This is the driver for Blackfin on-chip mac device. Say Y if you want it
Bryan Wue190d6b2007-07-17 14:43:44 +0800852 compiled into the kernel. This driver is also available as a module
853 ( = code which can be inserted in and removed from the running kernel
854 whenever you want). The module will be called bfin_mac.
855
856config BFIN_MAC_USE_L1
857 bool "Use L1 memory for rx/tx packets"
Michael Hennerich6893ff12008-01-30 16:52:25 +0800858 depends on BFIN_MAC && (BF527 || BF537)
Bryan Wue190d6b2007-07-17 14:43:44 +0800859 default y
860 help
Matt LaPlante01dd2fb2007-10-20 01:34:40 +0200861 To get maximum network performance, you should use L1 memory as rx/tx buffers.
Bryan Wue190d6b2007-07-17 14:43:44 +0800862 Say N here if you want to reserve L1 memory for other uses.
863
864config BFIN_TX_DESC_NUM
865 int "Number of transmit buffer packets"
866 depends on BFIN_MAC
867 range 6 10 if BFIN_MAC_USE_L1
868 range 10 100
869 default "10"
870 help
871 Set the number of buffer packets used in driver.
872
873config BFIN_RX_DESC_NUM
874 int "Number of receive buffer packets"
875 depends on BFIN_MAC
876 range 20 100 if BFIN_MAC_USE_L1
877 range 20 800
878 default "20"
879 help
880 Set the number of buffer packets used in driver.
881
882config BFIN_MAC_RMII
Mike Frysingere06d41d2010-02-15 14:32:50 +0000883 bool "RMII PHY Interface"
884 depends on BFIN_MAC
Michael Hennerich6893ff12008-01-30 16:52:25 +0800885 default y if BFIN527_EZKIT
886 default n if BFIN537_STAMP
Bryan Wue190d6b2007-07-17 14:43:44 +0800887 help
888 Use Reduced PHY MII Interface
889
Linus Torvalds1da177e2005-04-16 15:20:36 -0700890config SMC9194
891 tristate "SMC 9194 support"
892 depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
893 select CRC32
894 ---help---
895 This is support for the SMC9xxx based Ethernet cards. Choose this
896 option if you have a DELL laptop with the docking station, or
897 another SMC9192/9194 based chipset. Say Y if you want it compiled
898 into the kernel, and read the file
899 <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
900 available from <http://www.tldp.org/docs.html#howto>.
901
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800902 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -0700903 will be called smc9194.
904
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700905config SMC91X
906 tristate "SMC 91C9x/91C1xxx support"
907 select CRC32
908 select MII
David Howellsb920de12008-02-08 04:19:31 -0800909 depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || \
Greg Ungerer717ea4b2010-03-10 07:37:06 -0800910 MIPS || BLACKFIN || MN10300 || COLDFIRE
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700911 help
912 This is a driver for SMC's 91x series of Ethernet chipsets,
913 including the SMC91C94 and the SMC91C111. Say Y if you want it
914 compiled into the kernel, and read the file
915 <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
916 available from <http://www.linuxdoc.org/docs.html#howto>.
917
918 This driver is also available as a module ( = code which can be
919 inserted in and removed from the running kernel whenever you want).
920 The module will be called smc91x. If you want to compile it as a
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800921 module, say M here and read <file:Documentation/kbuild/modules.txt>.
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700922
Sascha Hauer92aa6742006-06-22 07:11:13 +0200923config NET_NETX
924 tristate "NetX Ethernet support"
925 select MII
Jan Engelhardtd1c0a652007-06-13 12:48:53 -0700926 depends on ARCH_NETX
Sascha Hauer92aa6742006-06-22 07:11:13 +0200927 help
928 This is support for the Hilscher netX builtin Ethernet ports
929
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800930 To compile this driver as a module, choose M here. The module
Sascha Hauer92aa6742006-06-22 07:11:13 +0200931 will be called netx-eth.
932
Anant Golea6286ee2009-05-18 15:19:01 -0700933config TI_DAVINCI_EMAC
934 tristate "TI DaVinci EMAC Support"
Sriramakrishnan8ee2bf92009-11-19 15:58:25 +0530935 depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
Anant Golea6286ee2009-05-18 15:19:01 -0700936 select PHYLIB
937 help
938 This driver supports TI's DaVinci Ethernet .
939
940 To compile this driver as a module, choose M here: the module
941 will be called davinci_emac_driver. This is recommended.
942
Sascha Hauera1365272005-05-05 15:14:15 -0700943config DM9000
944 tristate "DM9000 support"
Alex Landauf40d24d2007-07-12 12:11:48 +0800945 depends on ARM || BLACKFIN || MIPS
Sascha Hauera1365272005-05-05 15:14:15 -0700946 select CRC32
947 select MII
948 ---help---
949 Support for DM9000 chipset.
950
Adrian Bunk57ce45d2007-11-12 21:03:58 -0800951 To compile this driver as a module, choose M here. The module
952 will be called dm9000.
Sascha Hauera1365272005-05-05 15:14:15 -0700953
Ben Dooks485ca222008-06-24 22:16:06 +0100954config DM9000_DEBUGLEVEL
955 int "DM9000 maximum debug level"
956 depends on DM9000
957 default 4
958 help
959 The maximum level of debugging code compiled into the DM9000
960 driver.
961
Ben Dooksf8dd0ec2008-06-24 22:16:04 +0100962config DM9000_FORCE_SIMPLE_PHY_POLL
963 bool "Force simple NSR based PHY polling"
964 depends on DM9000
965 ---help---
966 This configuration forces the DM9000 to use the NSR's LinkStatus
967 bit to determine if the link is up or down instead of the more
968 costly MII PHY reads. Note, this will not work if the chip is
969 operating with an external PHY.
970
Claudio Lanconelli3ec9c112008-01-14 11:00:28 +0100971config ENC28J60
972 tristate "ENC28J60 support"
973 depends on EXPERIMENTAL && SPI && NET_ETHERNET
974 select CRC32
975 ---help---
976 Support for the Microchip EN28J60 ethernet chip.
977
Johann Felix Soden2bfc79d2008-02-05 03:13:58 -0800978 To compile this driver as a module, choose M here. The module will be
Claudio Lanconelli3ec9c112008-01-14 11:00:28 +0100979 called enc28j60.
980
981config ENC28J60_WRITEVERIFY
982 bool "Enable write verify"
983 depends on ENC28J60
984 ---help---
985 Enable the verify after the buffer write useful for debugging purpose.
986 If unsure, say N.
987
Thierry Redinga1702852009-03-27 00:12:24 -0700988config ETHOC
989 tristate "OpenCores 10/100 Mbps Ethernet MAC support"
Geert Uytterhoeven0ebe74e2009-11-20 09:19:10 +0000990 depends on NET_ETHERNET && HAS_IOMEM && HAS_DMA
Thierry Redinga1702852009-03-27 00:12:24 -0700991 select MII
992 select PHYLIB
Randy Dunlapc5cacb32009-04-08 15:41:25 -0700993 select CRC32
994 select BITREVERSE
Thierry Redinga1702852009-03-27 00:12:24 -0700995 help
996 Say Y here if you want to use the OpenCores 10/100 Mbps Ethernet MAC.
997
Kristoffer Glembod4c41132010-02-15 03:33:44 +0000998config GRETH
999 tristate "Aeroflex Gaisler GRETH Ethernet MAC support"
David S. Millercf261b22010-02-18 23:32:26 -08001000 depends on SPARC
Kristoffer Glembod4c41132010-02-15 03:33:44 +00001001 select PHYLIB
1002 select CRC32
1003 help
1004 Say Y here if you want to use the Aeroflex Gaisler GRETH Ethernet MAC.
1005
Dustin McIntire0a0c72c2006-04-19 20:24:51 -07001006config SMC911X
1007 tristate "SMSC LAN911[5678] support"
1008 select CRC32
1009 select MII
Catalin Marinasbd2c4972008-10-20 18:15:17 +01001010 depends on ARM || SUPERH
Dustin McIntire0a0c72c2006-04-19 20:24:51 -07001011 help
1012 This is a driver for SMSC's LAN911x series of Ethernet chipsets
1013 including the new LAN9115, LAN9116, LAN9117, and LAN9118.
1014 Say Y if you want it compiled into the kernel,
1015 and read the Ethernet-HOWTO, available from
1016 <http://www.linuxdoc.org/docs.html#howto>.
1017
1018 This driver is also available as a module. The module will be
1019 called smc911x. If you want to compile it as a module, say M
Alexander E. Patrakov39f5fb32007-03-16 18:28:43 +05001020 here and read <file:Documentation/kbuild/modules.txt>
Dustin McIntire0a0c72c2006-04-19 20:24:51 -07001021
Steve Glendinningfd9abb32008-11-05 00:35:37 +00001022config SMSC911X
1023 tristate "SMSC LAN911x/LAN921x families embedded ethernet support"
Manuel Laussb4efc562009-10-13 07:25:48 +00001024 depends on ARM || SUPERH || BLACKFIN || MIPS
Steve Glendinningfd9abb32008-11-05 00:35:37 +00001025 select CRC32
1026 select MII
1027 select PHYLIB
1028 ---help---
1029 Say Y here if you want support for SMSC LAN911x and LAN921x families
1030 of ethernet controllers.
1031
1032 To compile this driver as a module, choose M here and read
1033 <file:Documentation/networking/net-modules.txt>. The module
1034 will be called smsc911x.
1035
Linus Torvalds1da177e2005-04-16 15:20:36 -07001036config NET_VENDOR_RACAL
1037 bool "Racal-Interlan (Micom) NI cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001038 depends on ISA
Linus Torvalds1da177e2005-04-16 15:20:36 -07001039 help
1040 If you have a network (Ethernet) card belonging to this class, such
1041 as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO,
1042 available from <http://www.tldp.org/docs.html#howto>.
1043
1044 Note that the answer to this question doesn't directly affect the
1045 kernel: saying N will just cause the configurator to skip all
1046 the questions about NI cards. If you say Y, you will be asked for
1047 your specific card in the following questions.
1048
1049config NI5010
1050 tristate "NI5010 support (EXPERIMENTAL)"
1051 depends on NET_VENDOR_RACAL && ISA && EXPERIMENTAL && BROKEN_ON_SMP
1052 ---help---
1053 If you have a network (Ethernet) card of this type, say Y and read
1054 the Ethernet-HOWTO, available from
1055 <http://www.tldp.org/docs.html#howto>. Note that this is still
1056 experimental code.
1057
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001058 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001059 will be called ni5010.
1060
1061config NI52
1062 tristate "NI5210 support"
1063 depends on NET_VENDOR_RACAL && ISA
1064 help
1065 If you have a network (Ethernet) card of this type, say Y and read
1066 the Ethernet-HOWTO, available from
1067 <http://www.tldp.org/docs.html#howto>.
1068
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001069 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001070 will be called ni52.
1071
1072config NI65
1073 tristate "NI6510 support"
Al Viroa5532602005-05-04 05:39:42 +01001074 depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -07001075 help
1076 If you have a network (Ethernet) card of this type, say Y and read
1077 the Ethernet-HOWTO, available from
1078 <http://www.tldp.org/docs.html#howto>.
1079
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001080 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001081 will be called ni65.
1082
Ilya Yanok47964172009-03-11 23:26:02 -07001083config DNET
1084 tristate "Dave ethernet support (DNET)"
Ilya Yanok4b979262009-03-21 16:58:47 -07001085 depends on NET_ETHERNET && HAS_IOMEM
Ilya Yanok47964172009-03-11 23:26:02 -07001086 select PHYLIB
1087 help
1088 The Dave ethernet interface (DNET) is found on Qong Board FPGA.
1089 Say Y to include support for the DNET chip.
1090
1091 To compile this driver as a module, choose M here: the module
1092 will be called dnet.
1093
Linus Torvalds1da177e2005-04-16 15:20:36 -07001094source "drivers/net/tulip/Kconfig"
1095
1096config AT1700
1097 tristate "AT1700/1720 support (EXPERIMENTAL)"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001098 depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
Linus Torvalds1da177e2005-04-16 15:20:36 -07001099 select CRC32
1100 ---help---
1101 If you have a network (Ethernet) card of this type, say Y and read
1102 the Ethernet-HOWTO, available from
1103 <http://www.tldp.org/docs.html#howto>.
1104
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001105 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001106 will be called at1700.
1107
1108config DEPCA
1109 tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001110 depends on ISA || EISA || MCA
Linus Torvalds1da177e2005-04-16 15:20:36 -07001111 select CRC32
1112 ---help---
1113 If you have a network (Ethernet) card of this type, say Y and read
1114 the Ethernet-HOWTO, available from
1115 <http://www.tldp.org/docs.html#howto> as well as
1116 <file:drivers/net/depca.c>.
1117
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001118 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001119 will be called depca.
1120
1121config HP100
1122 tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001123 depends on ISA || EISA || PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07001124 help
1125 If you have a network (Ethernet) card of this type, say Y and read
1126 the Ethernet-HOWTO, available from
1127 <http://www.tldp.org/docs.html#howto>.
1128
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001129 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001130 will be called hp100.
1131
1132config NET_ISA
1133 bool "Other ISA cards"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001134 depends on ISA
Linus Torvalds1da177e2005-04-16 15:20:36 -07001135 ---help---
1136 If your network (Ethernet) card hasn't been mentioned yet and its
1137 bus system (that's the way the cards talks to the other components
1138 of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y.
1139 Make sure you know the name of your card. Read the Ethernet-HOWTO,
1140 available from <http://www.tldp.org/docs.html#howto>.
1141
1142 If unsure, say Y.
1143
1144 Note that the answer to this question doesn't directly affect the
1145 kernel: saying N will just cause the configurator to skip all
1146 the remaining ISA network card questions. If you say Y, you will be
1147 asked for your specific card in the following questions.
1148
1149config E2100
1150 tristate "Cabletron E21xx support"
1151 depends on NET_ISA
1152 select CRC32
1153 help
1154 If you have a network (Ethernet) card of this type, say Y and read
1155 the Ethernet-HOWTO, available from
1156 <http://www.tldp.org/docs.html#howto>.
1157
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001158 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001159 will be called e2100.
1160
1161config EWRK3
1162 tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
1163 depends on NET_ISA
1164 select CRC32
1165 ---help---
1166 This driver supports the DE203, DE204 and DE205 network (Ethernet)
1167 cards. If this is for you, say Y and read
1168 <file:Documentation/networking/ewrk3.txt> in the kernel source as
1169 well as the Ethernet-HOWTO, available from
1170 <http://www.tldp.org/docs.html#howto>.
1171
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001172 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001173 will be called ewrk3.
1174
1175config EEXPRESS
1176 tristate "EtherExpress 16 support"
1177 depends on NET_ISA
1178 ---help---
1179 If you have an EtherExpress16 network (Ethernet) card, say Y and
1180 read the Ethernet-HOWTO, available from
1181 <http://www.tldp.org/docs.html#howto>. Note that the Intel
1182 EtherExpress16 card used to be regarded as a very poor choice
1183 because the driver was very unreliable. We now have a new driver
1184 that should do better.
1185
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001186 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001187 will be called eexpress.
1188
1189config EEXPRESS_PRO
1190 tristate "EtherExpressPro support/EtherExpress 10 (i82595) support"
1191 depends on NET_ISA
1192 ---help---
1193 If you have a network (Ethernet) card of this type, say Y. This
Jon Mason47c51432006-02-12 11:53:04 -06001194 driver supports Intel i82595{FX,TX} based boards. Note however
Linus Torvalds1da177e2005-04-16 15:20:36 -07001195 that the EtherExpress PRO/100 Ethernet card has its own separate
1196 driver. Please read the Ethernet-HOWTO, available from
1197 <http://www.tldp.org/docs.html#howto>.
1198
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001199 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001200 will be called eepro.
1201
Linus Torvalds1da177e2005-04-16 15:20:36 -07001202config HPLAN_PLUS
1203 tristate "HP PCLAN+ (27247B and 27252A) support"
1204 depends on NET_ISA
1205 select CRC32
1206 help
1207 If you have a network (Ethernet) card of this type, say Y and read
1208 the Ethernet-HOWTO, available from
1209 <http://www.tldp.org/docs.html#howto>.
1210
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001211 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001212 will be called hp-plus.
1213
1214config HPLAN
1215 tristate "HP PCLAN (27245 and other 27xxx series) support"
1216 depends on NET_ISA
1217 select CRC32
1218 help
1219 If you have a network (Ethernet) card of this type, say Y and read
1220 the Ethernet-HOWTO, available from
1221 <http://www.tldp.org/docs.html#howto>.
1222
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001223 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001224 will be called hp.
1225
1226config LP486E
1227 tristate "LP486E on board Ethernet"
1228 depends on NET_ISA
1229 help
1230 Say Y here to support the 82596-based on-board Ethernet controller
1231 for the Panther motherboard, which is one of the two shipped in the
1232 Intel Professional Workstation.
1233
1234config ETH16I
1235 tristate "ICL EtherTeam 16i/32 support"
1236 depends on NET_ISA
1237 help
1238 If you have a network (Ethernet) card of this type, say Y and read
1239 the Ethernet-HOWTO, available from
1240 <http://www.tldp.org/docs.html#howto>.
1241
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001242 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001243 will be called eth16i.
1244
1245config NE2000
1246 tristate "NE2000/NE1000 support"
Atsushi Nemotoc7e65c12008-08-08 00:55:17 +09001247 depends on NET_ISA || (Q40 && m) || M32R || MACH_TX49XX
Linus Torvalds1da177e2005-04-16 15:20:36 -07001248 select CRC32
1249 ---help---
1250 If you have a network (Ethernet) card of this type, say Y and read
1251 the Ethernet-HOWTO, available from
1252 <http://www.tldp.org/docs.html#howto>. Many Ethernet cards
1253 without a specific driver are compatible with NE2000.
1254
1255 If you have a PCI NE2000 card however, say N here and Y to "PCI
Jesper Juhl28beaf62006-03-08 00:06:31 -08001256 NE2000 and clone support" under "EISA, VLB, PCI and on board
1257 controllers" below. If you have a NE2000 card and are running on
Linus Torvalds1da177e2005-04-16 15:20:36 -07001258 an MCA system (a bus system used on some IBM PS/2 computers and
1259 laptops), say N here and Y to "NE/2 (ne2000 MCA version) support",
1260 below.
1261
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001262 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001263 will be called ne.
1264
1265config ZNET
1266 tristate "Zenith Z-Note support (EXPERIMENTAL)"
Al Viroa5532602005-05-04 05:39:42 +01001267 depends on NET_ISA && EXPERIMENTAL && ISA_DMA_API
Linus Torvalds1da177e2005-04-16 15:20:36 -07001268 help
1269 The Zenith Z-Note notebook computer has a built-in network
1270 (Ethernet) card, and this is the Linux driver for it. Note that the
1271 IBM Thinkpad 300 is compatible with the Z-Note and is also supported
1272 by this driver. Read the Ethernet-HOWTO, available from
1273 <http://www.tldp.org/docs.html#howto>.
1274
1275config SEEQ8005
1276 tristate "SEEQ8005 support (EXPERIMENTAL)"
1277 depends on NET_ISA && EXPERIMENTAL
1278 help
1279 This is a driver for the SEEQ 8005 network (Ethernet) card. If this
1280 is for you, read the Ethernet-HOWTO, available from
1281 <http://www.tldp.org/docs.html#howto>.
1282
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001283 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001284 will be called seeq8005.
1285
Linus Torvalds1da177e2005-04-16 15:20:36 -07001286config NE2_MCA
1287 tristate "NE/2 (ne2000 MCA version) support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001288 depends on MCA_LEGACY
Linus Torvalds1da177e2005-04-16 15:20:36 -07001289 select CRC32
1290 help
1291 If you have a network (Ethernet) card of this type, say Y and read
1292 the Ethernet-HOWTO, available from
1293 <http://www.tldp.org/docs.html#howto>.
1294
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001295 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001296 will be called ne2.
1297
1298config IBMLANA
1299 tristate "IBM LAN Adapter/A support"
Adrian Bunke6353f32008-01-30 22:02:35 +02001300 depends on MCA
Linus Torvalds1da177e2005-04-16 15:20:36 -07001301 ---help---
1302 This is a Micro Channel Ethernet adapter. You need to set
1303 CONFIG_MCA to use this driver. It is both available as an in-kernel
1304 driver and as a module.
1305
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001306 To compile this driver as a module, choose M here. The only
Linus Torvalds1da177e2005-04-16 15:20:36 -07001307 currently supported card is the IBM LAN Adapter/A for Ethernet. It
1308 will both support 16K and 32K memory windows, however a 32K window
1309 gives a better security against packet losses. Usage of multiple
1310 boards with this driver should be possible, but has not been tested
1311 up to now due to lack of hardware.
1312
1313config IBMVETH
1314 tristate "IBM LAN Virtual Ethernet support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001315 depends on PPC_PSERIES
Linus Torvalds1da177e2005-04-16 15:20:36 -07001316 ---help---
1317 This driver supports virtual ethernet adapters on newer IBM iSeries
1318 and pSeries systems.
1319
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001320 To compile this driver as a module, choose M here. The module will
Linus Torvalds1da177e2005-04-16 15:20:36 -07001321 be called ibmveth.
1322
David Gibson1d3bb992007-08-23 13:56:01 +10001323source "drivers/net/ibm_newemac/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -07001324
1325config NET_PCI
1326 bool "EISA, VLB, PCI and on board controllers"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001327 depends on ISA || EISA || PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07001328 help
1329 This is another class of network cards which attach directly to the
1330 bus. If you have one of those, say Y and read the Ethernet-HOWTO,
1331 available from <http://www.tldp.org/docs.html#howto>.
1332
1333 Note that the answer to this question doesn't directly affect the
1334 kernel: saying N will just cause the configurator to skip all
1335 the questions about this class of network cards. If you say Y, you
1336 will be asked for your specific card in the following questions. If
1337 you are unsure, say Y.
1338
1339config PCNET32
1340 tristate "AMD PCnet32 PCI support"
1341 depends on NET_PCI && PCI
1342 select CRC32
1343 select MII
1344 help
1345 If you have a PCnet32 or PCnetPCI based network (Ethernet) card,
1346 answer Y here and read the Ethernet-HOWTO, available from
1347 <http://www.tldp.org/docs.html#howto>.
1348
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001349 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001350 will be called pcnet32.
1351
1352config AMD8111_ETH
1353 tristate "AMD 8111 (new PCI lance) support"
1354 depends on NET_PCI && PCI
1355 select CRC32
1356 select MII
1357 help
1358 If you have an AMD 8111-based PCI lance ethernet card,
1359 answer Y here and read the Ethernet-HOWTO, available from
1360 <http://www.tldp.org/docs.html#howto>.
1361
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001362 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001363 will be called amd8111e.
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001364
Linus Torvalds1da177e2005-04-16 15:20:36 -07001365config ADAPTEC_STARFIRE
1366 tristate "Adaptec Starfire/DuraLAN support"
1367 depends on NET_PCI && PCI
1368 select CRC32
1369 select MII
1370 help
1371 Say Y here if you have an Adaptec Starfire (or DuraLAN) PCI network
1372 adapter. The DuraLAN chip is used on the 64 bit PCI boards from
1373 Adaptec e.g. the ANA-6922A. The older 32 bit boards use the tulip
1374 driver.
1375
1376 To compile this driver as a module, choose M here: the module
1377 will be called starfire. This is recommended.
1378
Linus Torvalds1da177e2005-04-16 15:20:36 -07001379config AC3200
1380 tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)"
1381 depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL
1382 select CRC32
1383 help
1384 If you have a network (Ethernet) card of this type, say Y and read
1385 the Ethernet-HOWTO, available from
1386 <http://www.tldp.org/docs.html#howto>.
1387
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001388 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001389 will be called ac3200.
1390
Tristram Ha1eb1cc72010-02-08 11:38:28 +00001391config KSZ884X_PCI
1392 tristate "Micrel KSZ8841/2 PCI"
1393 depends on NET_PCI && PCI
1394 select MII
1395 select CRC32
1396 help
1397 This PCI driver is for Micrel KSZ8841/KSZ8842 PCI Ethernet chip.
1398
1399 To compile this driver as a module, choose M here. The module
1400 will be called ksz884x.
1401
Linus Torvalds1da177e2005-04-16 15:20:36 -07001402config APRICOT
1403 tristate "Apricot Xen-II on board Ethernet"
1404 depends on NET_PCI && ISA
1405 help
1406 If you have a network (Ethernet) controller of this type, say Y and
1407 read the Ethernet-HOWTO, available from
1408 <http://www.tldp.org/docs.html#howto>.
1409
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001410 To compile this driver as a module, choose M here. The module
1411 will be called apricot.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001412
1413config B44
Michael Buesch753f4922007-09-19 14:20:30 -07001414 tristate "Broadcom 440x/47xx ethernet support"
Al Viro46cb69c2008-05-21 06:32:11 +01001415 depends on SSB_POSSIBLE && HAS_DMA
Michael Buesch753f4922007-09-19 14:20:30 -07001416 select SSB
Linus Torvalds1da177e2005-04-16 15:20:36 -07001417 select MII
1418 help
Michael Buesch753f4922007-09-19 14:20:30 -07001419 If you have a network (Ethernet) controller of this type, say Y
1420 or M and read the Ethernet-HOWTO, available from
Linus Torvalds1da177e2005-04-16 15:20:36 -07001421 <http://www.tldp.org/docs.html#howto>.
1422
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001423 To compile this driver as a module, choose M here. The module
1424 will be called b44.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001425
Michael Buesch753f4922007-09-19 14:20:30 -07001426# Auto-select SSB PCI-HOST support, if possible
1427config B44_PCI_AUTOSELECT
1428 bool
1429 depends on B44 && SSB_PCIHOST_POSSIBLE
1430 select SSB_PCIHOST
1431 default y
1432
1433# Auto-select SSB PCICORE driver, if possible
1434config B44_PCICORE_AUTOSELECT
1435 bool
1436 depends on B44 && SSB_DRIVER_PCICORE_POSSIBLE
1437 select SSB_DRIVER_PCICORE
1438 default y
1439
1440config B44_PCI
1441 bool
1442 depends on B44_PCI_AUTOSELECT && B44_PCICORE_AUTOSELECT
1443 default y
1444
Linus Torvalds1da177e2005-04-16 15:20:36 -07001445config FORCEDETH
Adrian Bunk82770082006-03-08 00:06:30 -08001446 tristate "nForce Ethernet support"
1447 depends on NET_PCI && PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07001448 help
1449 If you have a network (Ethernet) controller of this type, say Y and
1450 read the Ethernet-HOWTO, available from
1451 <http://www.tldp.org/docs.html#howto>.
1452
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001453 To compile this driver as a module, choose M here. The module
1454 will be called forcedeth.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001455
Stephen Hemmingere27cdba2006-07-31 20:37:19 -07001456config FORCEDETH_NAPI
Randy Dunlapbf45abe2007-10-18 17:16:20 -07001457 bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
Stephen Hemmingere27cdba2006-07-31 20:37:19 -07001458 depends on FORCEDETH && EXPERIMENTAL
1459 help
1460 NAPI is a new driver API designed to reduce CPU and interrupt load
1461 when the driver is receiving lots of packets from the card. It is
1462 still somewhat experimental and thus not yet enabled by default.
1463
1464 If your estimated Rx load is 10kpps or more, or if the card will be
1465 deployed on potentially unfriendly networks (e.g. in a firewall),
1466 then say Y here.
1467
Stephen Hemmingere27cdba2006-07-31 20:37:19 -07001468 If in doubt, say N.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001469
1470config CS89x0
1471 tristate "CS89x0 support"
Gilles Chanteperdrix0ac4ed92008-09-26 15:44:43 +01001472 depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \
1473 || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001474 ---help---
1475 Support for CS89x0 chipset based Ethernet cards. If you have a
1476 network (Ethernet) card of this type, say Y and read the
1477 Ethernet-HOWTO, available from
1478 <http://www.tldp.org/docs.html#howto> as well as
1479 <file:Documentation/networking/cs89x0.txt>.
1480
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001481 To compile this driver as a module, choose M here. The module
1482 will be called cs89x0.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001483
Gilles Chanteperdrix0ac4ed92008-09-26 15:44:43 +01001484config CS89x0_NONISA_IRQ
1485 def_bool y
1486 depends on CS89x0 != n
1487 depends on MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS
1488
Linus Torvalds1da177e2005-04-16 15:20:36 -07001489config TC35815
1490 tristate "TOSHIBA TC35815 Ethernet support"
Atsushi Nemotoeea221c2007-03-03 23:54:59 +09001491 depends on NET_PCI && PCI && MIPS
Atsushi Nemotoc6686fe2008-04-12 00:47:46 +09001492 select PHYLIB
Linus Torvalds1da177e2005-04-16 15:20:36 -07001493
Linus Torvalds1da177e2005-04-16 15:20:36 -07001494config E100
1495 tristate "Intel(R) PRO/100+ support"
1496 depends on NET_PCI && PCI
1497 select MII
1498 ---help---
1499 This driver supports Intel(R) PRO/100 family of adapters.
1500 To verify that your adapter is supported, find the board ID number
1501 on the adapter. Look for a label that has a barcode and a number
1502 in the format 123456-001 (six digits hyphen three digits).
1503
1504 Use the above information and the Adapter & Driver ID Guide at:
1505
1506 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
1507
1508 to identify the adapter.
1509
1510 For the latest Intel PRO/100 network driver for Linux, see:
1511
1512 <http://appsr.intel.com/scripts-df/support_intel.asp>
1513
1514 More specific information on configuring the driver is in
1515 <file:Documentation/networking/e100.txt>.
1516
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001517 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001518 will be called e100.
1519
1520config LNE390
1521 tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)"
1522 depends on NET_PCI && EISA && EXPERIMENTAL
1523 select CRC32
1524 help
1525 If you have a network (Ethernet) card of this type, say Y and read
1526 the Ethernet-HOWTO, available from
1527 <http://www.tldp.org/docs.html#howto>.
1528
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001529 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001530 will be called lne390.
1531
1532config FEALNX
1533 tristate "Myson MTD-8xx PCI Ethernet support"
1534 depends on NET_PCI && PCI
1535 select CRC32
1536 select MII
1537 help
1538 Say Y here to support the Mysom MTD-800 family of PCI-based Ethernet
1539 cards. Specifications and data at
1540 <http://www.myson.com.hk/mtd/datasheet/>.
1541
1542config NATSEMI
1543 tristate "National Semiconductor DP8381x series PCI Ethernet support"
1544 depends on NET_PCI && PCI
1545 select CRC32
1546 help
1547 This driver is for the National Semiconductor DP83810 series,
1548 which is used in cards from PureData, NetGear, Linksys
1549 and others, including the 83815 chip.
1550 More specific information and updates are available from
1551 <http://www.scyld.com/network/natsemi.html>.
1552
1553config NE2K_PCI
1554 tristate "PCI NE2000 and clones support (see help)"
1555 depends on NET_PCI && PCI
1556 select CRC32
1557 ---help---
1558 This driver is for NE2000 compatible PCI cards. It will not work
1559 with ISA NE2000 cards (they have their own driver, "NE2000/NE1000
1560 support" below). If you have a PCI NE2000 network (Ethernet) card,
1561 say Y and read the Ethernet-HOWTO, available from
1562 <http://www.tldp.org/docs.html#howto>.
1563
1564 This driver also works for the following NE2000 clone cards:
1565 RealTek RTL-8029 Winbond 89C940 Compex RL2000 KTI ET32P2
1566 NetVin NV5000SC Via 86C926 SureCom NE34 Winbond
1567 Holtek HT80232 Holtek HT80229
1568
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001569 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001570 will be called ne2k-pci.
1571
1572config NE3210
1573 tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)"
1574 depends on NET_PCI && EISA && EXPERIMENTAL
1575 select CRC32
1576 ---help---
1577 If you have a network (Ethernet) card of this type, say Y and read
1578 the Ethernet-HOWTO, available from
1579 <http://www.tldp.org/docs.html#howto>. Note that this driver
1580 will NOT WORK for NE3200 cards as they are completely different.
1581
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001582 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001583 will be called ne3210.
1584
1585config ES3210
1586 tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)"
1587 depends on NET_PCI && EISA && EXPERIMENTAL
1588 select CRC32
1589 help
1590 If you have a network (Ethernet) card of this type, say Y and read
1591 the Ethernet-HOWTO, available from
1592 <http://www.tldp.org/docs.html#howto>.
1593
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001594 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001595 will be called es3210.
1596
1597config 8139CP
1598 tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)"
1599 depends on NET_PCI && PCI && EXPERIMENTAL
1600 select CRC32
1601 select MII
1602 help
1603 This is a driver for the Fast Ethernet PCI network cards based on
1604 the RTL8139C+ chips. If you have one of those, say Y and read
1605 the Ethernet-HOWTO, available from
1606 <http://www.tldp.org/docs.html#howto>.
1607
1608 To compile this driver as a module, choose M here: the module
1609 will be called 8139cp. This is recommended.
1610
1611config 8139TOO
Adrian Bunkf04e3f02005-05-16 21:13:03 +02001612 tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support"
Linus Torvalds1da177e2005-04-16 15:20:36 -07001613 depends on NET_PCI && PCI
1614 select CRC32
1615 select MII
1616 ---help---
1617 This is a driver for the Fast Ethernet PCI network cards based on
Adrian Bunkf04e3f02005-05-16 21:13:03 +02001618 the RTL 8129/8130/8139 chips. If you have one of those, say Y and
1619 read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001620
1621 To compile this driver as a module, choose M here: the module
1622 will be called 8139too. This is recommended.
1623
1624config 8139TOO_PIO
1625 bool "Use PIO instead of MMIO"
1626 default y
1627 depends on 8139TOO
1628 help
1629 This instructs the driver to use programmed I/O ports (PIO) instead
1630 of PCI shared memory (MMIO). This can possibly solve some problems
1631 in case your mainboard has memory consistency issues. If unsure,
1632 say N.
1633
1634config 8139TOO_TUNE_TWISTER
1635 bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)"
1636 depends on 8139TOO
1637 help
1638 This implements a function which might come in handy in case you
1639 are using low quality on long cabling. It is required for RealTek
1640 RTL-8139 revision K boards, and totally unused otherwise. It tries
1641 to match the transceiver to the cable characteristics. This is
1642 experimental since hardly documented by the manufacturer.
1643 If unsure, say Y.
1644
1645config 8139TOO_8129
1646 bool "Support for older RTL-8129/8130 boards"
1647 depends on 8139TOO
1648 help
1649 This enables support for the older and uncommon RTL-8129 and
1650 RTL-8130 chips, which support MII via an external transceiver,
1651 instead of an internal one. Disabling this option will save some
1652 memory by making the code size smaller. If unsure, say Y.
1653
1654config 8139_OLD_RX_RESET
1655 bool "Use older RX-reset method"
1656 depends on 8139TOO
1657 help
1658 The 8139too driver was recently updated to contain a more rapid
1659 reset sequence, in the face of severe receive errors. This "new"
1660 RX-reset method should be adequate for all boards. But if you
1661 experience problems, you can enable this option to restore the
1662 old RX-reset behavior. If unsure, say N.
1663
Sten Wang7a47dd72007-11-12 21:31:11 -08001664config R6040
Florian Fainelli68334112009-01-08 15:04:50 +00001665 tristate "RDC R6040 Fast Ethernet Adapter support"
Sten Wang7a47dd72007-11-12 21:31:11 -08001666 depends on NET_PCI && PCI
1667 select CRC32
1668 select MII
1669 help
1670 This is a driver for the R6040 Fast Ethernet MACs found in the
1671 the RDC R-321x System-on-chips.
1672
1673 To compile this driver as a module, choose M here: the module
1674 will be called r6040. This is recommended.
1675
Linus Torvalds1da177e2005-04-16 15:20:36 -07001676config SIS900
1677 tristate "SiS 900/7016 PCI Fast Ethernet Adapter support"
1678 depends on NET_PCI && PCI
1679 select CRC32
Adrian Bunk6da0f682005-04-30 13:52:49 +02001680 select MII
Linus Torvalds1da177e2005-04-16 15:20:36 -07001681 ---help---
1682 This is a driver for the Fast Ethernet PCI network cards based on
1683 the SiS 900 and SiS 7016 chips. The SiS 900 core is also embedded in
Adrian Bunkc3cf5602006-03-04 17:07:57 +01001684 SiS 630 and SiS 540 chipsets.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001685
1686 This driver also supports AMD 79C901 HomePNA so that you can use
1687 your phone line as a network cable.
1688
1689 To compile this driver as a module, choose M here: the module
1690 will be called sis900. This is recommended.
1691
1692config EPIC100
1693 tristate "SMC EtherPower II"
1694 depends on NET_PCI && PCI
1695 select CRC32
1696 select MII
1697 help
1698 This driver is for the SMC EtherPower II 9432 PCI Ethernet NIC,
1699 which is based on the SMC83c17x (EPIC/100).
1700 More specific information and updates are available from
1701 <http://www.scyld.com/network/epic100.html>.
1702
Steve Glendinning2cb37722008-12-11 20:54:30 -08001703config SMSC9420
1704 tristate "SMSC LAN9420 PCI ethernet adapter support"
1705 depends on NET_PCI && PCI
1706 select CRC32
1707 select PHYLIB
1708 select SMSC_PHY
1709 help
1710 This is a driver for SMSC's LAN9420 PCI ethernet adapter.
1711 Say Y if you want it compiled into the kernel,
1712 and read the Ethernet-HOWTO, available from
1713 <http://www.linuxdoc.org/docs.html#howto>.
1714
1715 This driver is also available as a module. The module will be
1716 called smsc9420. If you want to compile it as a module, say M
1717 here and read <file:Documentation/kbuild/modules.txt>
1718
Linus Torvalds1da177e2005-04-16 15:20:36 -07001719config SUNDANCE
1720 tristate "Sundance Alta support"
1721 depends on NET_PCI && PCI
1722 select CRC32
1723 select MII
1724 help
1725 This driver is for the Sundance "Alta" chip.
1726 More specific information and updates are available from
1727 <http://www.scyld.com/network/sundance.html>.
1728
1729config SUNDANCE_MMIO
1730 bool "Use MMIO instead of PIO"
1731 depends on SUNDANCE
1732 help
1733 Enable memory-mapped I/O for interaction with Sundance NIC registers.
1734 Do NOT enable this by default, PIO (enabled when MMIO is disabled)
1735 is known to solve bugs on certain chips.
1736
1737 If unsure, say N.
1738
1739config TLAN
1740 tristate "TI ThunderLAN support"
Stephen Hemminger93e16842008-05-30 09:49:55 -07001741 depends on NET_PCI && (PCI || EISA)
Linus Torvalds1da177e2005-04-16 15:20:36 -07001742 ---help---
1743 If you have a PCI Ethernet network card based on the ThunderLAN chip
1744 which is supported by this driver, say Y and read the
1745 Ethernet-HOWTO, available from
1746 <http://www.tldp.org/docs.html#howto>.
1747
1748 Devices currently supported by this driver are Compaq Netelligent,
1749 Compaq NetFlex and Olicom cards. Please read the file
1750 <file:Documentation/networking/tlan.txt> for more details.
1751
Adrian Bunk57ce45d2007-11-12 21:03:58 -08001752 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07001753 will be called tlan.
1754
1755 Please email feedback to <torben.mathiasen@compaq.com>.
1756
Richard Ršöjforsb07878e2009-06-04 03:35:55 +00001757config KS8842
1758 tristate "Micrel KSZ8842"
Heiko Carstens0cf08dc2009-06-22 21:32:18 +00001759 depends on HAS_IOMEM
Richard Ršöjforsb07878e2009-06-04 03:35:55 +00001760 help
Andreas Mohrc1893082009-08-21 00:46:06 +00001761 This platform driver is for Micrel KSZ8842 / KS8842
1762 2-port ethernet switch chip (managed, VLAN, QoS).
Richard Ršöjforsb07878e2009-06-04 03:35:55 +00001763
Ben Dooks3ba81f32009-07-16 05:24:08 +00001764config KS8851
1765 tristate "Micrel KS8851 SPI"
1766 depends on SPI
Alexander Beregalovde72e5d2009-07-22 01:16:51 +00001767 select MII
Randy Dunlapcbb35f82009-08-19 12:13:31 -07001768 select CRC32
Ben Dooks3ba81f32009-07-16 05:24:08 +00001769 help
1770 SPI driver for Micrel KS8851 SPI attached network chip.
1771
Choi, Davida55c0a0e2009-09-25 14:42:12 +00001772config KS8851_MLL
1773 tristate "Micrel KS8851 MLL"
1774 depends on HAS_IOMEM
Randy Dunlap47a01a02009-10-14 15:10:58 -07001775 select MII
Choi, Davida55c0a0e2009-09-25 14:42:12 +00001776 help
1777 This platform driver is for Micrel KS8851 Address/data bus
1778 multiplexed network chip.
1779
Linus Torvalds1da177e2005-04-16 15:20:36 -07001780config VIA_RHINE
1781 tristate "VIA Rhine support"
1782 depends on NET_PCI && PCI
1783 select CRC32
1784 select MII
1785 help
1786 If you have a VIA "Rhine" based network card (Rhine-I (VT86C100A),
1787 Rhine-II (VT6102), or Rhine-III (VT6105)), say Y here. Rhine-type
1788 Ethernet functions can also be found integrated on South Bridges
1789 (e.g. VT8235).
1790
1791 To compile this driver as a module, choose M here. The module
1792 will be called via-rhine.
1793
1794config VIA_RHINE_MMIO
1795 bool "Use MMIO instead of PIO"
1796 depends on VIA_RHINE
1797 help
1798 This instructs the driver to use PCI shared memory (MMIO) instead of
1799 programmed I/O ports (PIO). Enabling this gives an improvement in
1800 processing time in parts of the driver.
1801
1802 If unsure, say Y.
1803
Cesar Eduardo Barrosbf345702006-12-19 13:08:47 -08001804config SC92031
1805 tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
1806 depends on NET_PCI && PCI && EXPERIMENTAL
1807 select CRC32
1808 ---help---
1809 This is a driver for the Fast Ethernet PCI network cards based on
1810 the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you
1811 have one of these, say Y here.
1812
1813 To compile this driver as a module, choose M here: the module
1814 will be called sc92031. This is recommended.
1815
Matteo Croced95b39c2007-10-14 18:10:13 +02001816config CPMAC
1817 tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
Florian Fainelli839b04c2009-08-04 11:17:49 +00001818 depends on NET_ETHERNET && EXPERIMENTAL && AR7
Matteo Croced95b39c2007-10-14 18:10:13 +02001819 select PHYLIB
Matteo Croced95b39c2007-10-14 18:10:13 +02001820 help
1821 TI AR7 CPMAC Ethernet support
1822
Linus Torvalds1da177e2005-04-16 15:20:36 -07001823config NET_POCKET
1824 bool "Pocket and portable adapters"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001825 depends on PARPORT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001826 ---help---
1827 Cute little network (Ethernet) devices which attach to the parallel
1828 port ("pocket adapters"), commonly used with laptops. If you have
1829 one of those, say Y and read the Ethernet-HOWTO, available from
1830 <http://www.tldp.org/docs.html#howto>.
1831
1832 If you want to plug a network (or some other) card into the PCMCIA
1833 (or PC-card) slot of your laptop instead (PCMCIA is the standard for
1834 credit card size extension cards used by all modern laptops), you
1835 need the pcmcia-cs package (location contained in the file
1836 <file:Documentation/Changes>) and you can say N here.
1837
1838 Laptop users should read the Linux Laptop home page at
1839 <http://www.linux-on-laptops.com/> or
1840 Tuxmobil - Linux on Mobile Computers at <http://www.tuxmobil.org/>.
1841
1842 Note that the answer to this question doesn't directly affect the
1843 kernel: saying N will just cause the configurator to skip all
1844 the questions about this class of network devices. If you say Y, you
1845 will be asked for your specific device in the following questions.
1846
1847config ATP
1848 tristate "AT-LAN-TEC/RealTek pocket adapter support"
Grant Coady32fa2bf2005-09-10 00:14:05 +10001849 depends on NET_POCKET && PARPORT && X86
Linus Torvalds1da177e2005-04-16 15:20:36 -07001850 select CRC32
1851 ---help---
1852 This is a network (Ethernet) device which attaches to your parallel
1853 port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO,
1854 available from <http://www.tldp.org/docs.html#howto>, if you
1855 want to use this. If you intend to use this driver, you should have
1856 said N to the "Parallel printer support", because the two drivers
1857 don't like each other.
1858
1859 To compile this driver as a module, choose M here: the module
1860 will be called atp.
1861
1862config DE600
1863 tristate "D-Link DE600 pocket adapter support"
Grant Coady32fa2bf2005-09-10 00:14:05 +10001864 depends on NET_POCKET && PARPORT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001865 ---help---
1866 This is a network (Ethernet) device which attaches to your parallel
1867 port. Read <file:Documentation/networking/DLINK.txt> as well as the
1868 Ethernet-HOWTO, available from
1869 <http://www.tldp.org/docs.html#howto>, if you want to use
1870 this. It is possible to have several devices share a single parallel
1871 port and it is safe to compile the corresponding drivers into the
1872 kernel.
1873
1874 To compile this driver as a module, choose M here: the module
1875 will be called de600.
1876
1877config DE620
1878 tristate "D-Link DE620 pocket adapter support"
Grant Coady32fa2bf2005-09-10 00:14:05 +10001879 depends on NET_POCKET && PARPORT
Linus Torvalds1da177e2005-04-16 15:20:36 -07001880 ---help---
1881 This is a network (Ethernet) device which attaches to your parallel
1882 port. Read <file:Documentation/networking/DLINK.txt> as well as the
1883 Ethernet-HOWTO, available from
1884 <http://www.tldp.org/docs.html#howto>, if you want to use
1885 this. It is possible to have several devices share a single parallel
1886 port and it is safe to compile the corresponding drivers into the
1887 kernel.
1888
1889 To compile this driver as a module, choose M here: the module
1890 will be called de620.
1891
1892config SGISEEQ
1893 tristate "SGI Seeq ethernet controller support"
Thomas Bogendoerfer49b11bc2007-12-19 13:42:36 +01001894 depends on SGI_HAS_SEEQ
Linus Torvalds1da177e2005-04-16 15:20:36 -07001895 help
1896 Say Y here if you have an Seeq based Ethernet network card. This is
1897 used in many Silicon Graphics machines.
1898
1899config DECLANCE
1900 tristate "DEC LANCE ethernet controller support"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001901 depends on MACH_DECSTATION
Linus Torvalds1da177e2005-04-16 15:20:36 -07001902 select CRC32
1903 help
1904 This driver is for the series of Ethernet controllers produced by
1905 DEC (now Compaq) based on the AMD Lance chipset, including the
1906 DEPCA series. (This chipset is better known via the NE2100 cards.)
1907
1908config 68360_ENET
1909 bool "Motorola 68360 ethernet controller"
1910 depends on M68360
1911 help
1912 Say Y here if you want to use the built-in ethernet controller of
1913 the Motorola 68360 processor.
1914
1915config FEC
Fabio Estevam64423302009-05-27 03:41:39 +00001916 bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
Amit Kucheriabd011e82010-02-05 08:56:22 +00001917 depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
1918 MACH_MX27 || ARCH_MX35 || ARCH_MX25 || ARCH_MX5
Linus Torvalds1da177e2005-04-16 15:20:36 -07001919 help
1920 Say Y here if you want to use the built-in 10/100 Fast ethernet
Sascha Hauer196719e2009-01-28 23:03:10 +00001921 controller on some Motorola ColdFire and Freescale i.MX processors.
Greg Ungerer2af69212005-09-12 11:18:10 +10001922
1923config FEC2
1924 bool "Second FEC ethernet controller (on some ColdFire CPUs)"
1925 depends on FEC
1926 help
1927 Say Y here if you want to use the second built-in 10/100 Fast
1928 ethernet controller on some Motorola ColdFire processors.
Linus Torvalds1da177e2005-04-16 15:20:36 -07001929
Domen Puncer5d031e92007-10-26 18:07:49 +02001930config FEC_MPC52xx
1931 tristate "MPC52xx FEC driver"
Grant Likely847cdf42008-11-14 05:19:00 -07001932 depends on PPC_MPC52xx && PPC_BESTCOMM
Domen Puncer5d031e92007-10-26 18:07:49 +02001933 select CRC32
1934 select PHYLIB
Grant Likely847cdf42008-11-14 05:19:00 -07001935 select PPC_BESTCOMM_FEC
Domen Puncer5d031e92007-10-26 18:07:49 +02001936 ---help---
1937 This option enables support for the MPC5200's on-chip
1938 Fast Ethernet Controller
Pavel Machek4737f092009-06-05 00:44:53 +02001939 If compiled as module, it will be called fec_mpc52xx.
Domen Puncer5d031e92007-10-26 18:07:49 +02001940
1941config FEC_MPC52xx_MDIO
1942 bool "MPC52xx FEC MDIO bus driver"
1943 depends on FEC_MPC52xx
1944 default y
1945 ---help---
1946 The MPC5200's FEC can connect to the Ethernet either with
1947 an external MII PHY chip or 10 Mbps 7-wire interface
1948 (Motorola? industry standard).
1949 If your board uses an external PHY connected to FEC, enable this.
1950 If not sure, enable.
Pavel Machek4737f092009-06-05 00:44:53 +02001951 If compiled as module, it will be called fec_mpc52xx_phy.
Domen Puncer5d031e92007-10-26 18:07:49 +02001952
Linus Torvalds1da177e2005-04-16 15:20:36 -07001953config NE_H8300
1954 tristate "NE2000 compatible support for H8/300"
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001955 depends on H8300
Linus Torvalds1da177e2005-04-16 15:20:36 -07001956 help
1957 Say Y here if you want to use the NE2000 compatible
1958 controller on the Renesas H8/300 processor.
1959
Chris Snook452c1ce2008-09-14 19:56:10 -05001960config ATL2
1961 tristate "Atheros L2 Fast Ethernet support"
1962 depends on PCI
1963 select CRC32
1964 select MII
1965 help
1966 This driver supports the Atheros L2 fast ethernet adapter.
1967
1968 To compile this driver as a module, choose M here. The module
1969 will be called atl2.
1970
John Linnbb81b2d2009-08-20 02:52:16 -07001971config XILINX_EMACLITE
1972 tristate "Xilinx 10/100 Ethernet Lite support"
1973 depends on PPC32 || MICROBLAZE
John Linn5cdaaa12010-02-15 21:51:00 -08001974 select PHYLIB
John Linnbb81b2d2009-08-20 02:52:16 -07001975 help
1976 This driver supports the 10/100 Ethernet Lite from Xilinx.
1977
Maxime Bizon9b1fc552009-08-18 13:23:40 +01001978config BCM63XX_ENET
1979 tristate "Broadcom 63xx internal mac support"
1980 depends on BCM63XX
1981 select MII
1982 select PHYLIB
1983 help
1984 This driver supports the ethernet MACs in the Broadcom 63xx
1985 MIPS chipset family (BCM63XX).
1986
Pantelis Antoniou48257c42005-10-28 16:25:58 -04001987source "drivers/net/fs_enet/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -07001988
David Daneyd6aa60a2009-10-14 12:04:41 -07001989source "drivers/net/octeon/Kconfig"
1990
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07001991endif # NET_ETHERNET
Linus Torvalds1da177e2005-04-16 15:20:36 -07001992
1993#
1994# Gigabit Ethernet
1995#
1996
Jan Engelhardtf30486d2007-05-10 22:52:56 -07001997menuconfig NETDEV_1000
1998 bool "Ethernet (1000 Mbit)"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07001999 depends on !UML
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002000 default y
Jan Engelhardt06bfb7e2007-08-18 12:56:21 +02002001 ---help---
2002 Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
2003 type of Local Area Network (LAN) in universities and companies.
2004
2005 Say Y here to get to see options for Gigabit Ethernet drivers.
2006 This option alone does not add any kernel code.
2007 Note that drivers supporting both 100 and 1000 MBit may be listed
2008 under "Ethernet (10 or 100MBit)" instead.
2009
2010 If you say N, all options in this submenu will be skipped and disabled.
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002011
2012if NETDEV_1000
Linus Torvalds1da177e2005-04-16 15:20:36 -07002013
2014config ACENIC
2015 tristate "Alteon AceNIC/3Com 3C985/NetGear GA620 Gigabit support"
2016 depends on PCI
2017 ---help---
2018 Say Y here if you have an Alteon AceNIC, 3Com 3C985(B), NetGear
2019 GA620, SGI Gigabit or Farallon PN9000-SX PCI Gigabit Ethernet
2020 adapter. The driver allows for using the Jumbo Frame option (9000
2021 bytes/frame) however it requires that your switches can handle this
2022 as well. To enable Jumbo Frames, add `mtu 9000' to your ifconfig
2023 line.
2024
2025 To compile this driver as a module, choose M here: the
2026 module will be called acenic.
2027
2028config ACENIC_OMIT_TIGON_I
2029 bool "Omit support for old Tigon I based AceNICs"
2030 depends on ACENIC
2031 help
2032 Say Y here if you only have Tigon II based AceNICs and want to leave
2033 out support for the older Tigon I based cards which are no longer
2034 being sold (ie. the original Alteon AceNIC and 3Com 3C985 (non B
2035 version)). This will reduce the size of the driver object by
2036 app. 100KB. If you are not sure whether your card is a Tigon I or a
2037 Tigon II, say N here.
2038
2039 The safe and default value for this is N.
2040
2041config DL2K
Komurodf950822007-08-13 09:45:41 +09002042 tristate "DL2000/TC902x-based Gigabit Ethernet support"
Linus Torvalds1da177e2005-04-16 15:20:36 -07002043 depends on PCI
2044 select CRC32
2045 help
Komurodf950822007-08-13 09:45:41 +09002046 This driver supports DL2000/TC902x-based Gigabit ethernet cards,
2047 which includes
Linus Torvalds1da177e2005-04-16 15:20:36 -07002048 D-Link DGE-550T Gigabit Ethernet Adapter.
2049 D-Link DL2000-based Gigabit Ethernet Adapter.
Komurodf950822007-08-13 09:45:41 +09002050 Sundance/Tamarack TC902x Gigabit Ethernet Adapter.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002051
2052 To compile this driver as a module, choose M here: the
2053 module will be called dl2k.
2054
2055config E1000
2056 tristate "Intel(R) PRO/1000 Gigabit Ethernet support"
2057 depends on PCI
2058 ---help---
2059 This driver supports Intel(R) PRO/1000 gigabit ethernet family of
2060 adapters. For more information on how to identify your adapter, go
2061 to the Adapter & Driver ID Guide at:
2062
2063 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2064
2065 For general information and support, go to the Intel support
2066 website at:
2067
2068 <http://support.intel.com>
2069
2070 More specific information on configuring the driver is in
2071 <file:Documentation/networking/e1000.txt>.
2072
Adrian Bunk57ce45d2007-11-12 21:03:58 -08002073 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07002074 will be called e1000.
2075
Auke Kokbc7f75f2007-09-17 12:30:59 -07002076config E1000E
2077 tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
Al Viro7ac86bf2008-04-27 06:15:42 +01002078 depends on PCI && (!SPARC32 || BROKEN)
Auke Kokbc7f75f2007-09-17 12:30:59 -07002079 ---help---
2080 This driver supports the PCI-Express Intel(R) PRO/1000 gigabit
2081 ethernet family of adapters. For PCI or PCI-X e1000 adapters,
2082 use the regular e1000 driver For more information on how to
2083 identify your adapter, go to the Adapter & Driver ID Guide at:
2084
2085 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2086
2087 For general information and support, go to the Intel support
2088 website at:
2089
2090 <http://support.intel.com>
2091
Adrian Bunk57ce45d2007-11-12 21:03:58 -08002092 To compile this driver as a module, choose M here. The module
Auke Kokbc7f75f2007-09-17 12:30:59 -07002093 will be called e1000e.
2094
Stephen Hemmingerab7a9832008-01-01 09:27:58 -08002095config IP1000
2096 tristate "IP1000 Gigabit Ethernet support"
2097 depends on PCI && EXPERIMENTAL
2098 select MII
2099 ---help---
2100 This driver supports IP1000 gigabit Ethernet cards.
2101
2102 To compile this driver as a module, choose M here: the module
2103 will be called ipg. This is recommended.
2104
Auke Kok9d5c8242008-01-24 02:22:38 -08002105config IGB
Alexander Duyck3ef6b232008-11-20 00:46:57 -08002106 tristate "Intel(R) 82575/82576 PCI-Express Gigabit Ethernet support"
Auke Kok9d5c8242008-01-24 02:22:38 -08002107 depends on PCI
2108 ---help---
Alexander Duyck3ef6b232008-11-20 00:46:57 -08002109 This driver supports Intel(R) 82575/82576 gigabit ethernet family of
Auke Kok9d5c8242008-01-24 02:22:38 -08002110 adapters. For more information on how to identify your adapter, go
2111 to the Adapter & Driver ID Guide at:
2112
2113 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2114
2115 For general information and support, go to the Intel support
2116 website at:
2117
2118 <http://support.intel.com>
2119
2120 More specific information on configuring the driver is in
2121 <file:Documentation/networking/e1000.txt>.
2122
Johann Felix Soden2bfc79d2008-02-05 03:13:58 -08002123 To compile this driver as a module, choose M here. The module
Auke Kok9d5c8242008-01-24 02:22:38 -08002124 will be called igb.
2125
Jeff Kirsher421e02f2008-10-17 11:08:31 -07002126config IGB_DCA
Jeff Kirsher1d19ecf2008-11-02 20:30:33 -08002127 bool "Direct Cache Access (DCA) Support"
Jeff Kirsher421e02f2008-10-17 11:08:31 -07002128 default y
2129 depends on IGB && DCA && !(IGB=y && DCA=m)
Jeff Kirsher1d19ecf2008-11-02 20:30:33 -08002130 ---help---
2131 Say Y here if you want to use Direct Cache Access (DCA) in the
2132 driver. DCA is a method for warming the CPU cache before data
2133 is used, with the intent of lessening the impact of cache misses.
Jeff Kirsher421e02f2008-10-17 11:08:31 -07002134
Alexander Duyckd4e0fe02009-04-07 14:37:34 +00002135config IGBVF
2136 tristate "Intel(R) 82576 Virtual Function Ethernet support"
2137 depends on PCI
2138 ---help---
2139 This driver supports Intel(R) 82576 virtual functions. For more
2140 information on how to identify your adapter, go to the Adapter &
2141 Driver ID Guide at:
2142
2143 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2144
2145 For general information and support, go to the Intel support
2146 website at:
2147
2148 <http://support.intel.com>
2149
2150 More specific information on configuring the driver is in
2151 <file:Documentation/networking/e1000.txt>.
2152
2153 To compile this driver as a module, choose M here. The module
2154 will be called igbvf.
2155
Lennert Buytenhek15d014d2005-11-11 18:23:13 +01002156source "drivers/net/ixp2000/Kconfig"
2157
Linus Torvalds1da177e2005-04-16 15:20:36 -07002158config MYRI_SBUS
2159 tristate "MyriCOM Gigabit Ethernet support"
2160 depends on SBUS
2161 help
2162 This driver supports MyriCOM Sbus gigabit Ethernet cards.
2163
2164 To compile this driver as a module, choose M here: the module
2165 will be called myri_sbus. This is recommended.
2166
2167config NS83820
Jon Mason47c51432006-02-12 11:53:04 -06002168 tristate "National Semiconductor DP83820 support"
Linus Torvalds1da177e2005-04-16 15:20:36 -07002169 depends on PCI
2170 help
2171 This is a driver for the National Semiconductor DP83820 series
2172 of gigabit ethernet MACs. Cards using this chipset include
2173 the D-Link DGE-500T, PureData's PDP8023Z-TG, SMC's SMC9462TX,
2174 SOHO-GA2000T, SOHO-GA2500T. The driver supports the use of
2175 zero copy.
2176
2177config HAMACHI
2178 tristate "Packet Engines Hamachi GNIC-II support"
2179 depends on PCI
2180 select MII
2181 help
2182 If you have a Gigabit Ethernet card of this type, say Y and read
2183 the Ethernet-HOWTO, available from
2184 <http://www.tldp.org/docs.html#howto>.
2185
Adrian Bunk57ce45d2007-11-12 21:03:58 -08002186 To compile this driver as a module, choose M here. The module will be
Linus Torvalds1da177e2005-04-16 15:20:36 -07002187 called hamachi.
2188
2189config YELLOWFIN
2190 tristate "Packet Engines Yellowfin Gigabit-NIC support (EXPERIMENTAL)"
2191 depends on PCI && EXPERIMENTAL
2192 select CRC32
2193 ---help---
2194 Say Y here if you have a Packet Engines G-NIC PCI Gigabit Ethernet
2195 adapter or the SYM53C885 Ethernet controller. The Gigabit adapter is
2196 used by the Beowulf Linux cluster project. See
2197 <http://cesdis.gsfc.nasa.gov/linux/drivers/yellowfin.html> for more
2198 information about this driver in particular and Beowulf in general.
2199
2200 To compile this driver as a module, choose M here: the module
2201 will be called yellowfin. This is recommended.
2202
2203config R8169
2204 tristate "Realtek 8169 gigabit ethernet support"
2205 depends on PCI
2206 select CRC32
Francois Romieub7372492008-09-13 15:04:38 +02002207 select MII
Linus Torvalds1da177e2005-04-16 15:20:36 -07002208 ---help---
2209 Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter.
2210
2211 To compile this driver as a module, choose M here: the module
2212 will be called r8169. This is recommended.
2213
Linus Torvalds1da177e2005-04-16 15:20:36 -07002214config R8169_VLAN
2215 bool "VLAN support"
2216 depends on R8169 && VLAN_8021Q
2217 ---help---
2218 Say Y here for the r8169 driver to support the functions required
2219 by the kernel 802.1Q code.
Francois Romieu865c6522008-05-11 14:51:00 +02002220
Linus Torvalds1da177e2005-04-16 15:20:36 -07002221 If in doubt, say Y.
2222
Maciej W. Rozycki1a9e8542007-09-14 12:05:00 +01002223config SB1250_MAC
Maciej W. Rozycki25a72df2007-09-14 11:57:33 +01002224 tristate "SB1250 Gigabit Ethernet support"
2225 depends on SIBYTE_SB1xxx_SOC
Maciej W. Rozyckif5279ff2007-09-21 12:52:10 +01002226 select PHYLIB
Maciej W. Rozycki25a72df2007-09-14 11:57:33 +01002227 ---help---
2228 This driver supports Gigabit Ethernet interfaces based on the
2229 Broadcom SiByte family of System-On-a-Chip parts. They include
2230 the BCM1120, BCM1125, BCM1125H, BCM1250, BCM1255, BCM1280, BCM1455
2231 and BCM1480 chips.
2232
2233 To compile this driver as a module, choose M here: the module
2234 will be called sb1250-mac.
2235
Francois Romieu890e8d02005-07-30 13:08:43 +02002236config SIS190
Francois Romieue7976372005-09-03 00:57:51 +02002237 tristate "SiS190/SiS191 gigabit ethernet support"
Adrian Bunke9985d52005-08-09 02:41:00 +02002238 depends on PCI
2239 select CRC32
2240 select MII
2241 ---help---
Francois Romieue7976372005-09-03 00:57:51 +02002242 Say Y here if you have a SiS 190 PCI Fast Ethernet adapter or
2243 a SiS 191 PCI Gigabit Ethernet adapter. Both are expected to
2244 appear in lan on motherboard designs which are based on SiS 965
2245 and SiS 966 south bridge.
Francois Romieu890e8d02005-07-30 13:08:43 +02002246
Adrian Bunke9985d52005-08-09 02:41:00 +02002247 To compile this driver as a module, choose M here: the module
2248 will be called sis190. This is recommended.
Francois Romieu890e8d02005-07-30 13:08:43 +02002249
Stephen Hemmingerbaef58b2005-05-12 20:14:36 -04002250config SKGE
Stephen Hemminger7a160c72006-02-13 15:48:08 -08002251 tristate "New SysKonnect GigaEthernet support"
2252 depends on PCI
Stephen Hemmingerbaef58b2005-05-12 20:14:36 -04002253 select CRC32
2254 ---help---
2255 This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
2256 and related Gigabit Ethernet adapters. It is a new smaller driver
Stephen Hemminger46a60f22005-09-09 12:54:56 -07002257 with better performance and more complete ethtool support.
Stephen Hemmingerbaef58b2005-05-12 20:14:36 -04002258
2259 It does not support the link failover and network management
Stephen Hemminger5ad887f2007-09-15 19:35:14 -04002260 features that "portable" vendor supplied sk98lin driver does.
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002261
Daniel Drakec6f0d752006-01-21 19:35:34 +00002262 This driver supports adapters based on the original Yukon chipset:
2263 Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T,
2264 Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872.
2265
2266 It does not support the newer Yukon2 chipset: a separate driver,
2267 sky2, is provided for Yukon2-based adapters.
2268
2269 To compile this driver as a module, choose M here: the module
2270 will be called skge. This is recommended.
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002271
Stephen Hemminger678aa1f2007-10-16 12:15:54 -07002272config SKGE_DEBUG
2273 bool "Debugging interface"
2274 depends on SKGE && DEBUG_FS
2275 help
2276 This option adds the ability to dump driver state for debugging.
GeunSik Lim156f5a72009-06-02 15:01:37 +09002277 The file /sys/kernel/debug/skge/ethX displays the state of the internal
Stephen Hemminger678aa1f2007-10-16 12:15:54 -07002278 transmit and receive rings.
2279
2280 If unsure, say N.
2281
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002282config SKY2
Stephen Hemminger8a3e3bf2007-07-09 15:33:38 -07002283 tristate "SysKonnect Yukon2 support"
Stephen Hemmingerf479b322006-10-27 10:22:10 -07002284 depends on PCI
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002285 select CRC32
2286 ---help---
Matt LaPlantecab00892006-10-03 22:36:44 +02002287 This driver supports Gigabit Ethernet adapters based on the
Daniel Drakec6f0d752006-01-21 19:35:34 +00002288 Marvell Yukon 2 chipset:
2289 Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/
2290 88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21
2291
Stephen Hemmingerf479b322006-10-27 10:22:10 -07002292 There is companion driver for the older Marvell Yukon and
2293 Genesis based adapters: skge.
Stephen Hemmingercd28ab62005-08-16 16:36:49 -07002294
2295 To compile this driver as a module, choose M here: the module
2296 will be called sky2. This is recommended.
2297
Stephen Hemminger3cf26752007-07-09 15:33:35 -07002298config SKY2_DEBUG
2299 bool "Debugging interface"
2300 depends on SKY2 && DEBUG_FS
2301 help
2302 This option adds the ability to dump driver state for debugging.
GeunSik Lim156f5a72009-06-02 15:01:37 +09002303 The file /sys/kernel/debug/sky2/ethX displays the state of the internal
Stephen Hemminger3cf26752007-07-09 15:33:35 -07002304 transmit and receive rings.
Daniel Drakec6f0d752006-01-21 19:35:34 +00002305
Stephen Hemminger3cf26752007-07-09 15:33:35 -07002306 If unsure, say N.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002307
2308config VIA_VELOCITY
2309 tristate "VIA Velocity support"
Yoichi Yuasa73815532007-05-24 16:12:27 +09002310 depends on PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07002311 select CRC32
2312 select CRC_CCITT
2313 select MII
2314 help
2315 If you have a VIA "Velocity" based network card say Y here.
2316
2317 To compile this driver as a module, choose M here. The module
2318 will be called via-velocity.
2319
2320config TIGON3
2321 tristate "Broadcom Tigon3 support"
2322 depends on PCI
Matt Carlson158d7ab2008-05-29 01:37:54 -07002323 select PHYLIB
Linus Torvalds1da177e2005-04-16 15:20:36 -07002324 help
2325 This driver supports Broadcom Tigon3 based gigabit Ethernet cards.
2326
2327 To compile this driver as a module, choose M here: the module
2328 will be called tg3. This is recommended.
2329
Michael Chanb6016b72005-05-26 13:03:09 -07002330config BNX2
2331 tristate "Broadcom NetXtremeII support"
2332 depends on PCI
Michael Chanfba9fe92006-06-12 22:21:25 -07002333 select CRC32
Michael Chan57579f72009-04-04 16:51:14 -07002334 select FW_LOADER
Michael Chanb6016b72005-05-26 13:03:09 -07002335 help
2336 This driver supports Broadcom NetXtremeII gigabit Ethernet cards.
2337
2338 To compile this driver as a module, choose M here: the module
2339 will be called bnx2. This is recommended.
2340
Michael Chana4636962009-06-08 18:14:43 -07002341config CNIC
2342 tristate "Broadcom CNIC support"
Michael Chanbabdb782009-06-10 13:35:28 -07002343 depends on PCI
2344 select BNX2
2345 select UIO
Michael Chana4636962009-06-08 18:14:43 -07002346 help
2347 This driver supports offload features of Broadcom NetXtremeII
2348 gigabit Ethernet cards.
2349
2350 To compile this driver as a module, choose M here: the module
2351 will be called cnic. This is recommended.
2352
Jens Osterkampaaec0fa2005-09-05 15:19:29 -07002353config SPIDER_NET
2354 tristate "Spider Gigabit Ethernet driver"
Kou Ishizaki3342cf02007-02-20 16:36:14 -06002355 depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
Christoph Hellwig9b158792006-03-15 11:30:44 +01002356 select FW_LOADER
Jens Osterkampaaec0fa2005-09-05 15:19:29 -07002357 help
2358 This driver supports the Gigabit Ethernet chips present on the
2359 Cell Processor-Based Blades from IBM.
2360
Zang Roy-r619115e123b82006-11-08 19:49:13 -08002361config TSI108_ETH
2362 tristate "Tundra TSI108 gigabit Ethernet support"
2363 depends on TSI108_BRIDGE
2364 help
2365 This driver supports Tundra TSI108 gigabit Ethernet ports.
2366 To compile this driver as a module, choose M here: the module
2367 will be called tsi108_eth.
2368
Masakazu Mokuno02c18892007-07-05 20:11:16 +09002369config GELIC_NET
2370 tristate "PS3 Gigabit Ethernet driver"
2371 depends on PPC_PS3
Geoff Levand1d32e212008-04-10 07:01:53 +10002372 select PS3_SYS_MANAGER
Masakazu Mokuno02c18892007-07-05 20:11:16 +09002373 help
2374 This driver supports the network device on the PS3 game
2375 console. This driver has built-in support for Ethernet.
2376
2377 To compile this driver as a module, choose M here: the
2378 module will be called ps3_gelic.
2379
Masakazu Mokuno09dde542008-02-07 19:58:57 +09002380config GELIC_WIRELESS
John W. Linville97ed8392008-03-06 13:08:09 -05002381 bool "PS3 Wireless support"
Benjamin Herrenschmidt92c6f8d2009-12-18 11:19:32 -08002382 depends on WLAN
John W. Linville97ed8392008-03-06 13:08:09 -05002383 depends on GELIC_NET
2384 select WIRELESS_EXT
2385 help
2386 This option adds the support for the wireless feature of PS3.
2387 If you have the wireless-less model of PS3 or have no plan to
2388 use wireless feature, disabling this option saves memory. As
2389 the driver automatically distinguishes the models, you can
2390 safely enable this option even if you have a wireless-less model.
Masakazu Mokuno09dde542008-02-07 19:58:57 +09002391
Andy Fleming1577ece2009-02-04 16:42:12 -08002392config FSL_PQ_MDIO
2393 tristate "Freescale PQ MDIO"
2394 depends on FSL_SOC
2395 select PHYLIB
2396 help
2397 This driver supports the MDIO bus used by the gianfar and UCC drivers.
2398
Linus Torvalds1da177e2005-04-16 15:20:36 -07002399config GIANFAR
2400 tristate "Gianfar Ethernet"
Kumar Gala3a831562008-01-28 10:24:30 -06002401 depends on FSL_SOC
Andy Fleming1577ece2009-02-04 16:42:12 -08002402 select FSL_PQ_MDIO
Andy Flemingbb40dcb2005-09-23 22:54:21 -04002403 select PHYLIB
Dave Jiangbf41a7c2007-04-12 10:57:06 -07002404 select CRC32
Linus Torvalds1da177e2005-04-16 15:20:36 -07002405 help
Jon Loeligeref82a302006-06-17 17:52:55 -05002406 This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
2407 and MPC86xx family of chips, and the FEC on the 8540.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002408
Li Yangce973b12006-08-14 23:00:11 -07002409config UCC_GETH
Timur Tabi7d776cb2007-03-12 15:40:27 -05002410 tristate "Freescale QE Gigabit Ethernet"
2411 depends on QUICC_ENGINE
Andy Fleming1577ece2009-02-04 16:42:12 -08002412 select FSL_PQ_MDIO
Jan Altenberg296baae2007-06-01 00:46:29 -07002413 select PHYLIB
Li Yangce973b12006-08-14 23:00:11 -07002414 help
Timur Tabi7d776cb2007-03-12 15:40:27 -05002415 This driver supports the Gigabit Ethernet mode of the QUICC Engine,
2416 which is available on some Freescale SOCs.
Li Yangce973b12006-08-14 23:00:11 -07002417
Michael Reissd5b90492007-04-13 01:26:19 -05002418config UGETH_TX_ON_DEMAND
2419 bool "Transmit on Demand support"
Li Yangce973b12006-08-14 23:00:11 -07002420 depends on UCC_GETH
2421
Linus Torvalds1da177e2005-04-16 15:20:36 -07002422config MV643XX_ETH
Lennert Buytenhek9c1bbdf2007-10-19 04:11:03 +02002423 tristate "Marvell Discovery (643XX) and Orion ethernet support"
Gabriel Paubertdfa92642009-05-25 22:46:19 -07002424 depends on MV64X60 || PPC32 || PLAT_ORION
Lennert Buytenhekab307a32009-02-24 15:41:32 +00002425 select INET_LRO
Lennert Buytenheked944932008-08-26 13:34:19 +02002426 select PHYLIB
Linus Torvalds1da177e2005-04-16 15:20:36 -07002427 help
Lennert Buytenhek9c1bbdf2007-10-19 04:11:03 +02002428 This driver supports the gigabit ethernet MACs in the
2429 Marvell Discovery PPC/MIPS chipset family (MV643XX) and
2430 in the Marvell Orion ARM SoC family.
2431
2432 Some boards that use the Discovery chipset are the Momenco
2433 Ocelot C and Jaguar ATX and Pegasos II.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002434
Grant Likely92744982009-04-25 12:53:39 +00002435config XILINX_LL_TEMAC
2436 tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
2437 select PHYLIB
2438 depends on PPC_DCR_NATIVE
2439 help
2440 This driver supports the Xilinx 10/100/1000 LocalLink TEMAC
2441 core used in Xilinx Spartan and Virtex FPGAs
2442
Ron Mercer5a4faa82006-07-25 00:40:21 -07002443config QLA3XXX
2444 tristate "QLogic QLA3XXX Network Driver Support"
2445 depends on PCI
2446 help
2447 This driver supports QLogic ISP3XXX gigabit Ethernet cards.
2448
2449 To compile this driver as a module, choose M here: the module
2450 will be called qla3xxx.
2451
Jay Cliburnf3cc28c2007-02-08 10:42:37 -05002452config ATL1
Jay Cliburna6d1f362008-09-27 04:17:22 +00002453 tristate "Atheros/Attansic L1 Gigabit Ethernet support"
2454 depends on PCI
Jay Cliburnf3cc28c2007-02-08 10:42:37 -05002455 select CRC32
2456 select MII
2457 help
Jay Cliburna6d1f362008-09-27 04:17:22 +00002458 This driver supports the Atheros/Attansic L1 gigabit ethernet
2459 adapter.
Jay Cliburnf3cc28c2007-02-08 10:42:37 -05002460
2461 To compile this driver as a module, choose M here. The module
2462 will be called atl1.
2463
Jie Yanga6a53252008-07-18 11:37:13 +08002464config ATL1E
2465 tristate "Atheros L1E Gigabit Ethernet support (EXPERIMENTAL)"
2466 depends on PCI && EXPERIMENTAL
2467 select CRC32
2468 select MII
2469 help
2470 This driver supports the Atheros L1E gigabit ethernet adapter.
2471
2472 To compile this driver as a module, choose M here. The module
2473 will be called atl1e.
2474
Jie Yang43250dd2009-02-18 17:24:15 -08002475config ATL1C
2476 tristate "Atheros L1C Gigabit Ethernet support (EXPERIMENTAL)"
2477 depends on PCI && EXPERIMENTAL
2478 select CRC32
2479 select MII
2480 help
2481 This driver supports the Atheros L1C gigabit ethernet adapter.
2482
2483 To compile this driver as a module, choose M here. The module
2484 will be called atl1c.
2485
Guo-Fu Tseng95252232008-09-16 01:00:11 +08002486config JME
2487 tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
2488 depends on PCI
2489 select CRC32
2490 select MII
2491 ---help---
2492 This driver supports the PCI-Express gigabit ethernet adapters
2493 based on JMicron JMC250 chipset.
2494
2495 To compile this driver as a module, choose M here. The module
2496 will be called jme.
2497
Oskar Schirmer8b0215a2009-06-10 12:58:48 -07002498config S6GMAC
2499 tristate "S6105 GMAC ethernet support"
2500 depends on XTENSA_VARIANT_S6000
2501 select PHYLIB
2502 help
2503 This driver supports the on chip ethernet device on the
2504 S6105 xtensa processor.
2505
2506 To compile this driver as a module, choose M here. The module
2507 will be called s6gmac.
2508
Giuseppe Cavallaro47dd7a52009-10-14 15:13:45 -07002509source "drivers/net/stmmac/Kconfig"
2510
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002511endif # NETDEV_1000
Linus Torvalds1da177e2005-04-16 15:20:36 -07002512
2513#
2514# 10 Gigabit Ethernet
2515#
2516
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002517menuconfig NETDEV_10000
2518 bool "Ethernet (10000 Mbit)"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07002519 depends on !UML
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002520 default y
Jan Engelhardt06bfb7e2007-08-18 12:56:21 +02002521 ---help---
2522 Say Y here to get to see options for 10 Gigabit Ethernet drivers.
2523 This option alone does not add any kernel code.
2524
2525 If you say N, all options in this submenu will be skipped and disabled.
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002526
2527if NETDEV_10000
Linus Torvalds1da177e2005-04-16 15:20:36 -07002528
Ben Hutchings1b1c2e92009-04-29 08:04:46 +00002529config MDIO
2530 tristate
2531
Christoph Lameter8199d3a2005-03-30 13:34:31 -08002532config CHELSIO_T1
2533 tristate "Chelsio 10Gb Ethernet support"
2534 depends on PCI
Stephen Hemminger57834ca2006-12-01 16:36:19 -08002535 select CRC32
Ben Hutchings23c33202009-04-29 08:06:34 +00002536 select MDIO
Christoph Lameter8199d3a2005-03-30 13:34:31 -08002537 help
Stephen Hemmingerf1d3d382006-12-01 16:36:16 -08002538 This driver supports Chelsio gigabit and 10-gigabit
2539 Ethernet cards. More information about adapter features and
2540 performance tuning is in <file:Documentation/networking/cxgb.txt>.
Christoph Lameter8199d3a2005-03-30 13:34:31 -08002541
2542 For general information about Chelsio and our products, visit
2543 our website at <http://www.chelsio.com>.
2544
2545 For customer support, please visit our customer support page at
2546 <http://www.chelsio.com/support.htm>.
2547
2548 Please send feedback to <linux-bugs@chelsio.com>.
2549
2550 To compile this driver as a module, choose M here: the module
2551 will be called cxgb.
2552
Stephen Hemminger352c4172006-12-01 16:36:17 -08002553config CHELSIO_T1_1G
2554 bool "Chelsio gigabit Ethernet support"
2555 depends on CHELSIO_T1
2556 help
2557 Enables support for Chelsio's gigabit Ethernet PCI cards. If you
2558 are using only 10G cards say 'N' here.
2559
James Bottomley58daa682008-12-30 10:20:24 -06002560config CHELSIO_T3_DEPENDS
2561 tristate
2562 depends on PCI && INET
2563 default y
2564
Divy Le Ray4d22de32007-01-18 22:04:14 -05002565config CHELSIO_T3
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002566 tristate "Chelsio Communications T3 10Gb Ethernet support"
James Bottomley58daa682008-12-30 10:20:24 -06002567 depends on CHELSIO_T3_DEPENDS
Divy Le Ray2e283962007-03-18 13:10:06 -07002568 select FW_LOADER
Ben Hutchings0f07c4e2009-04-29 08:07:20 +00002569 select MDIO
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002570 help
2571 This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
2572 adapters.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002573
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002574 For general information about Chelsio and our products, visit
2575 our website at <http://www.chelsio.com>.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002576
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002577 For customer support, please visit our customer support page at
2578 <http://www.chelsio.com/support.htm>.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002579
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002580 Please send feedback to <linux-bugs@chelsio.com>.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002581
Divy Le Ray194c1fb2007-03-21 19:21:00 -07002582 To compile this driver as a module, choose M here: the module
2583 will be called cxgb3.
Divy Le Ray4d22de32007-01-18 22:04:14 -05002584
Dimitris Michailidis43e9da82010-04-01 15:28:27 +00002585config CHELSIO_T4_DEPENDS
2586 tristate
2587 depends on PCI && INET
2588 default y
2589
2590config CHELSIO_T4
2591 tristate "Chelsio Communications T4 Ethernet support"
2592 depends on CHELSIO_T4_DEPENDS
2593 select FW_LOADER
2594 select MDIO
2595 help
2596 This driver supports Chelsio T4-based gigabit and 10Gb Ethernet
2597 adapters.
2598
2599 For general information about Chelsio and our products, visit
2600 our website at <http://www.chelsio.com>.
2601
2602 For customer support, please visit our customer support page at
2603 <http://www.chelsio.com/support.htm>.
2604
2605 Please send feedback to <linux-bugs@chelsio.com>.
2606
2607 To compile this driver as a module choose M here; the module
2608 will be called cxgb4.
2609
Jan-Bernd Themann7a291082006-09-13 17:44:31 +02002610config EHEA
2611 tristate "eHEA Ethernet support"
Nathan Lynch60d50192008-06-04 08:31:28 +10002612 depends on IBMEBUS && INET && SPARSEMEM
Jan-Bernd Themannd4dc4ec2007-09-25 16:16:34 -07002613 select INET_LRO
Jan-Bernd Themann7a291082006-09-13 17:44:31 +02002614 ---help---
2615 This driver supports the IBM pSeries eHEA ethernet adapter.
2616
2617 To compile the driver as a module, choose M here. The module
2618 will be called ehea.
2619
Scott Feldman01f2e4e2008-09-15 09:17:11 -07002620config ENIC
Roland Dreiereb8a4cb2008-10-13 18:53:05 -07002621 tristate "Cisco 10G Ethernet NIC support"
Scott Feldman01f2e4e2008-09-15 09:17:11 -07002622 depends on PCI && INET
2623 select INET_LRO
2624 help
2625 This enables the support for the Cisco 10G Ethernet card.
2626
Auke Kok9a799d72007-09-15 14:07:45 -07002627config IXGBE
2628 tristate "Intel(R) 10GbE PCI Express adapters support"
Mallikarjuna R Chilakala177db6f2008-06-18 15:32:19 -07002629 depends on PCI && INET
Ben Hutchings6b73e102009-04-29 08:08:58 +00002630 select MDIO
Auke Kok9a799d72007-09-15 14:07:45 -07002631 ---help---
2632 This driver supports Intel(R) 10GbE PCI Express family of
2633 adapters. For more information on how to identify your adapter, go
2634 to the Adapter & Driver ID Guide at:
2635
2636 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2637
2638 For general information and support, go to the Intel support
2639 website at:
2640
2641 <http://support.intel.com>
2642
Adrian Bunk57ce45d2007-11-12 21:03:58 -08002643 To compile this driver as a module, choose M here. The module
Auke Kok9a799d72007-09-15 14:07:45 -07002644 will be called ixgbe.
2645
Jeff Garzik5dd2d332008-10-16 05:09:31 -04002646config IXGBE_DCA
Jeff Kirsher1d19ecf2008-11-02 20:30:33 -08002647 bool "Direct Cache Access (DCA) Support"
Jeff Garzik5dd2d332008-10-16 05:09:31 -04002648 default y
2649 depends on IXGBE && DCA && !(IXGBE=y && DCA=m)
Jeff Kirsher1d19ecf2008-11-02 20:30:33 -08002650 ---help---
2651 Say Y here if you want to use Direct Cache Access (DCA) in the
2652 driver. DCA is a method for warming the CPU cache before data
2653 is used, with the intent of lessening the impact of cache misses.
Jeff Garzik5dd2d332008-10-16 05:09:31 -04002654
Jeff Kirsher7a6b6f52008-11-25 01:02:08 -08002655config IXGBE_DCB
Alexander Duyck2f90b862008-11-20 20:52:10 -08002656 bool "Data Center Bridging (DCB) Support"
2657 default n
Jeff Kirsher7a6b6f52008-11-25 01:02:08 -08002658 depends on IXGBE && DCB
Alexander Duyck2f90b862008-11-20 20:52:10 -08002659 ---help---
2660 Say Y here if you want to use Data Center Bridging (DCB) in the
2661 driver.
2662
2663 If unsure, say N.
2664
Greg Roseecc67032010-01-09 02:24:50 +00002665config IXGBEVF
2666 tristate "Intel(R) 82599 Virtual Function Ethernet support"
2667 depends on PCI_MSI
2668 ---help---
2669 This driver supports Intel(R) 82599 virtual functions. For more
2670 information on how to identify your adapter, go to the Adapter &
2671 Driver ID Guide at:
2672
2673 <http://support.intel.com/support/network/sb/CS-008441.htm>
2674
2675 For general information and support, go to the Intel support
2676 website at:
2677
2678 <http://support.intel.com>
2679
2680 More specific information on configuring the driver is in
2681 <file:Documentation/networking/ixgbevf.txt>.
2682
2683 To compile this driver as a module, choose M here. The module
2684 will be called ixgbevf. MSI-X interrupt support is required
2685 for this driver to work correctly.
2686
Linus Torvalds1da177e2005-04-16 15:20:36 -07002687config IXGB
2688 tristate "Intel(R) PRO/10GbE support"
2689 depends on PCI
2690 ---help---
Auke Kok9a799d72007-09-15 14:07:45 -07002691 This driver supports Intel(R) PRO/10GbE family of adapters for
2692 PCI-X type cards. For PCI-E type cards, use the "ixgbe" driver
2693 instead. For more information on how to identify your adapter, go
Linus Torvalds1da177e2005-04-16 15:20:36 -07002694 to the Adapter & Driver ID Guide at:
2695
2696 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
2697
2698 For general information and support, go to the Intel support
2699 website at:
2700
2701 <http://support.intel.com>
2702
2703 More specific information on configuring the driver is in
2704 <file:Documentation/networking/ixgb.txt>.
2705
Adrian Bunk57ce45d2007-11-12 21:03:58 -08002706 To compile this driver as a module, choose M here. The module
Linus Torvalds1da177e2005-04-16 15:20:36 -07002707 will be called ixgb.
2708
Linus Torvalds1da177e2005-04-16 15:20:36 -07002709config S2IO
2710 tristate "S2IO 10Gbe XFrame NIC"
2711 depends on PCI
2712 ---help---
2713 This driver supports the 10Gbe XFrame NIC of S2IO.
Akinobu Mita9eb343a2005-10-21 19:06:42 +09002714 More specific information on configuring the driver is in
2715 <file:Documentation/networking/s2io.txt>.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002716
Ramkrishna Vepaf1782852009-04-01 18:15:24 +00002717config VXGE
2718 tristate "Neterion X3100 Series 10GbE PCIe Server Adapter"
2719 depends on PCI && INET
2720 ---help---
2721 This driver supports Neterion Inc's X3100 Series 10 GbE PCIe
2722 I/O Virtualized Server Adapter.
2723 More specific information on configuring the driver is in
2724 <file:Documentation/networking/vxge.txt>.
2725
2726config VXGE_DEBUG_TRACE_ALL
2727 bool "Enabling All Debug trace statments in driver"
2728 default n
2729 depends on VXGE
2730 ---help---
2731 Say Y here if you want to enabling all the debug trace statements in
2732 driver. By default only few debug trace statements are enabled.
2733
Brice Goglin0da34b62006-05-23 06:10:15 -04002734config MYRI10GE
2735 tristate "Myricom Myri-10G Ethernet support"
Randy Dunlape0d5dab2007-10-18 21:53:50 -07002736 depends on PCI && INET
Brice Goglin0da34b62006-05-23 06:10:15 -04002737 select FW_LOADER
2738 select CRC32
Andrew Gallatin1e6e9342007-09-17 11:37:42 -07002739 select INET_LRO
Brice Goglin0da34b62006-05-23 06:10:15 -04002740 ---help---
2741 This driver supports Myricom Myri-10G Dual Protocol interface in
2742 Ethernet mode. If the eeprom on your board is not recent enough,
2743 you will need a newer firmware image.
2744 You may get this image or more information, at:
2745
Brice Goglind2794902006-09-05 21:58:50 -04002746 <http://www.myri.com/scs/download-Myri10GE.html>
Brice Goglin0da34b62006-05-23 06:10:15 -04002747
Adrian Bunk57ce45d2007-11-12 21:03:58 -08002748 To compile this driver as a module, choose M here. The module
Brice Goglin0da34b62006-05-23 06:10:15 -04002749 will be called myri10ge.
2750
Jeff Garzik5dd2d332008-10-16 05:09:31 -04002751config MYRI10GE_DCA
Jeff Kirsher1d19ecf2008-11-02 20:30:33 -08002752 bool "Direct Cache Access (DCA) Support"
Jeff Garzik5dd2d332008-10-16 05:09:31 -04002753 default y
2754 depends on MYRI10GE && DCA && !(MYRI10GE=y && DCA=m)
Jeff Kirsher1d19ecf2008-11-02 20:30:33 -08002755 ---help---
2756 Say Y here if you want to use Direct Cache Access (DCA) in the
2757 driver. DCA is a method for warming the CPU cache before data
2758 is used, with the intent of lessening the impact of cache misses.
Jeff Garzik5dd2d332008-10-16 05:09:31 -04002759
Amit S. Kale3d396eb2006-10-21 15:33:03 -04002760config NETXEN_NIC
2761 tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC"
Randy Dunlap5ac36612006-11-16 21:39:11 -08002762 depends on PCI
Amit S. Kale3d396eb2006-10-21 15:33:03 -04002763 help
2764 This enables the support for NetXen's Gigabit Ethernet card.
2765
David S. Millera3138df2007-10-09 01:54:01 -07002766config NIU
2767 tristate "Sun Neptune 10Gbit Ethernet support"
2768 depends on PCI
Randy Dunlapc557c152009-12-10 13:50:56 -08002769 select CRC32
David S. Millera3138df2007-10-09 01:54:01 -07002770 help
2771 This enables support for cards based upon Sun's
2772 Neptune chipset.
2773
Olof Johanssonf5cd7872007-01-31 21:43:54 -06002774config PASEMI_MAC
2775 tristate "PA Semi 1/10Gbit MAC"
Michael Ellerman5beaf7d2008-03-28 12:17:33 +11002776 depends on PPC_PASEMI && PCI
Olof Johanssonbb6e9592007-05-08 00:47:54 -05002777 select PHYLIB
Olof Johansson28ae79f2007-11-28 20:57:27 -06002778 select INET_LRO
Olof Johanssonf5cd7872007-01-31 21:43:54 -06002779 help
2780 This driver supports the on-chip 1/10Gbit Ethernet controller on
2781 PA Semi's PWRficient line of chips.
2782
Yevgeny Petrilinc27a02c2008-10-22 15:47:49 -07002783config MLX4_EN
2784 tristate "Mellanox Technologies 10Gbit Ethernet support"
2785 depends on PCI && INET
2786 select MLX4_CORE
2787 select INET_LRO
2788 help
2789 This driver supports Mellanox Technologies ConnectX Ethernet
2790 devices.
2791
Roland Dreier225c7b12007-05-08 18:00:38 -07002792config MLX4_CORE
2793 tristate
2794 depends on PCI
2795 default n
2796
2797config MLX4_DEBUG
2798 bool "Verbose debugging output" if (MLX4_CORE && EMBEDDED)
Paul Mundtf550d942007-05-10 12:50:28 +09002799 depends on MLX4_CORE
Roland Dreier225c7b12007-05-08 18:00:38 -07002800 default y
2801 ---help---
2802 This option causes debugging code to be compiled into the
2803 mlx4_core driver. The output can be turned on via the
2804 debug_level module parameter (which can also be set after
2805 the driver is loaded through sysfs).
2806
Andy Gospodarek1a348cc2007-09-17 18:50:36 -07002807config TEHUTI
2808 tristate "Tehuti Networks 10G Ethernet"
2809 depends on PCI
2810 help
2811 Tehuti Networks 10G Ethernet NIC
2812
Eliezer Tamira2fbb9e2007-11-15 20:09:02 +02002813config BNX2X
2814 tristate "Broadcom NetXtremeII 10Gb support"
2815 depends on PCI
Vladislav Zolotarov94a78b72009-04-27 03:27:43 -07002816 select FW_LOADER
Lee Schermerhorn07b270e2007-12-13 16:02:59 -08002817 select ZLIB_INFLATE
Eilon Greenstein34f80b02008-06-23 20:33:01 -07002818 select LIBCRC32C
Eilon Greenstein01cd4522009-08-12 08:23:08 +00002819 select MDIO
Eliezer Tamira2fbb9e2007-11-15 20:09:02 +02002820 help
2821 This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
2822 To compile this driver as a module, choose M here: the module
2823 will be called bnx2x. This is recommended.
2824
Amit Kumar Salecha0ec00f02010-01-13 00:37:26 +00002825config QLCNIC
2826 tristate "QLOGIC QLCNIC 1/10Gb Converged Ethernet NIC Support"
2827 depends on PCI
2828 help
2829 This driver supports QLogic QLE8240 and QLE8242 Converged Ethernet
2830 devices.
2831
Ron Mercerc4e84bd2008-09-18 11:56:28 -04002832config QLGE
2833 tristate "QLogic QLGE 10Gb Ethernet Driver Support"
2834 depends on PCI
2835 help
2836 This driver supports QLogic ISP8XXX 10Gb Ethernet cards.
2837
2838 To compile this driver as a module, choose M here: the module
2839 will be called qlge.
2840
Ben Hutchings8ceee662008-04-27 12:55:59 +01002841source "drivers/net/sfc/Kconfig"
Eliezer Tamira2fbb9e2007-11-15 20:09:02 +02002842
Sathya Perla6b7c5b92009-03-11 23:32:03 -07002843source "drivers/net/benet/Kconfig"
2844
Jan Engelhardtf30486d2007-05-10 22:52:56 -07002845endif # NETDEV_10000
Linus Torvalds1da177e2005-04-16 15:20:36 -07002846
Linus Torvalds1da177e2005-04-16 15:20:36 -07002847source "drivers/net/tokenring/Kconfig"
2848
2849source "drivers/net/wireless/Kconfig"
2850
Inaky Perez-Gonzalez143ee2d2008-12-23 16:18:48 -08002851source "drivers/net/wimax/Kconfig"
2852
Jeff Garzik5b2fc492007-05-09 21:31:55 -04002853source "drivers/net/usb/Kconfig"
2854
Linus Torvalds1da177e2005-04-16 15:20:36 -07002855source "drivers/net/pcmcia/Kconfig"
Linus Torvalds1da177e2005-04-16 15:20:36 -07002856
2857source "drivers/net/wan/Kconfig"
2858
2859source "drivers/atm/Kconfig"
2860
Sergey Lapin84594642009-06-08 12:18:51 +00002861source "drivers/ieee802154/Kconfig"
2862
Linus Torvalds1da177e2005-04-16 15:20:36 -07002863source "drivers/s390/net/Kconfig"
2864
Jeremy Fitzhardinge0d160212007-07-17 18:37:06 -07002865config XEN_NETDEV_FRONTEND
2866 tristate "Xen network device frontend driver"
2867 depends on XEN
2868 default y
2869 help
2870 The network device frontend driver allows the kernel to
2871 access network devices exported exported by a virtual
2872 machine containing a physical network device driver. The
2873 frontend driver is intended for unprivileged guest domains;
2874 if you are compiling a kernel for a Xen guest, you almost
2875 certainly want to enable this.
2876
Linus Torvalds1da177e2005-04-16 15:20:36 -07002877config ISERIES_VETH
2878 tristate "iSeries Virtual Ethernet driver support"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07002879 depends on PPC_ISERIES
Linus Torvalds1da177e2005-04-16 15:20:36 -07002880
Matt Porterf89efd52005-09-09 12:10:10 -07002881config RIONET
2882 tristate "RapidIO Ethernet over messaging driver support"
Randy Dunlapa81c52a2006-11-01 21:18:58 -08002883 depends on RAPIDIO
Matt Porterf89efd52005-09-09 12:10:10 -07002884
2885config RIONET_TX_SIZE
2886 int "Number of outbound queue entries"
2887 depends on RIONET
2888 default "128"
2889
2890config RIONET_RX_SIZE
2891 int "Number of inbound queue entries"
2892 depends on RIONET
2893 default "128"
2894
Linus Torvalds1da177e2005-04-16 15:20:36 -07002895config FDDI
Dave Joneseb560922008-12-27 20:43:48 -08002896 tristate "FDDI driver support"
Maciej W. Rozyckie89a2cf2007-02-05 16:28:27 -08002897 depends on (PCI || EISA || TC)
Linus Torvalds1da177e2005-04-16 15:20:36 -07002898 help
2899 Fiber Distributed Data Interface is a high speed local area network
2900 design; essentially a replacement for high speed Ethernet. FDDI can
2901 run over copper or fiber. If you are connected to such a network and
2902 want a driver for the FDDI card in your computer, say Y here (and
2903 then also Y to the driver for your FDDI card, below). Most people
2904 will say N.
2905
2906config DEFXX
Maciej W. Rozyckie89a2cf2007-02-05 16:28:27 -08002907 tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
2908 depends on FDDI && (PCI || EISA || TC)
2909 ---help---
2910 This is support for the DIGITAL series of TURBOchannel (DEFTA),
2911 EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
2912 to a local FDDI network.
2913
2914 To compile this driver as a module, choose M here: the module
2915 will be called defxx. If unsure, say N.
2916
2917config DEFXX_MMIO
2918 bool
2919 prompt "Use MMIO instead of PIO" if PCI || EISA
2920 depends on DEFXX
2921 default n if PCI || EISA
2922 default y
2923 ---help---
2924 This instructs the driver to use EISA or PCI memory-mapped I/O
2925 (MMIO) as appropriate instead of programmed I/O ports (PIO).
2926 Enabling this gives an improvement in processing time in parts
2927 of the driver, but it may cause problems with EISA (DEFEA)
2928 adapters. TURBOchannel does not have the concept of I/O ports,
2929 so MMIO is always used for these (DEFTA) adapters.
2930
2931 If unsure, say N.
Linus Torvalds1da177e2005-04-16 15:20:36 -07002932
2933config SKFP
2934 tristate "SysKonnect FDDI PCI support"
2935 depends on FDDI && PCI
Akinobu Mitabc63eb92006-12-19 13:09:08 -08002936 select BITREVERSE
Linus Torvalds1da177e2005-04-16 15:20:36 -07002937 ---help---
2938 Say Y here if you have a SysKonnect FDDI PCI adapter.
2939 The following adapters are supported by this driver:
2940 - SK-5521 (SK-NET FDDI-UP)
2941 - SK-5522 (SK-NET FDDI-UP DAS)
2942 - SK-5541 (SK-NET FDDI-FP)
2943 - SK-5543 (SK-NET FDDI-LP)
2944 - SK-5544 (SK-NET FDDI-LP DAS)
2945 - SK-5821 (SK-NET FDDI-UP64)
2946 - SK-5822 (SK-NET FDDI-UP64 DAS)
2947 - SK-5841 (SK-NET FDDI-FP64)
2948 - SK-5843 (SK-NET FDDI-LP64)
2949 - SK-5844 (SK-NET FDDI-LP64 DAS)
2950 - Netelligent 100 FDDI DAS Fibre SC
2951 - Netelligent 100 FDDI SAS Fibre SC
2952 - Netelligent 100 FDDI DAS UTP
2953 - Netelligent 100 FDDI SAS UTP
2954 - Netelligent 100 FDDI SAS Fibre MIC
2955
2956 Read <file:Documentation/networking/skfp.txt> for information about
2957 the driver.
2958
2959 Questions concerning this driver can be addressed to:
2960 <linux@syskonnect.de>
2961
2962 To compile this driver as a module, choose M here: the module
2963 will be called skfp. This is recommended.
2964
2965config HIPPI
2966 bool "HIPPI driver support (EXPERIMENTAL)"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07002967 depends on EXPERIMENTAL && INET && PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07002968 help
2969 HIgh Performance Parallel Interface (HIPPI) is a 800Mbit/sec and
2970 1600Mbit/sec dual-simplex switched or point-to-point network. HIPPI
2971 can run over copper (25m) or fiber (300m on multi-mode or 10km on
2972 single-mode). HIPPI networks are commonly used for clusters and to
2973 connect to super computers. If you are connected to a HIPPI network
2974 and have a HIPPI network card in your computer that you want to use
2975 under Linux, say Y here (you must also remember to enable the driver
2976 for your HIPPI card below). Most people will say N here.
2977
2978config ROADRUNNER
2979 tristate "Essential RoadRunner HIPPI PCI adapter support (EXPERIMENTAL)"
2980 depends on HIPPI && PCI
2981 help
2982 Say Y here if this is your PCI HIPPI network card.
2983
2984 To compile this driver as a module, choose M here: the module
2985 will be called rrunner. If unsure, say N.
2986
2987config ROADRUNNER_LARGE_RINGS
2988 bool "Use large TX/RX rings (EXPERIMENTAL)"
2989 depends on ROADRUNNER
2990 help
2991 If you say Y here, the RoadRunner driver will preallocate up to 2 MB
2992 of additional memory to allow for fastest operation, both for
2993 transmitting and receiving. This memory cannot be used by any other
2994 kernel code or by user space programs. Say Y here only if you have
2995 the memory.
2996
2997config PLIP
2998 tristate "PLIP (parallel port) support"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07002999 depends on PARPORT
Linus Torvalds1da177e2005-04-16 15:20:36 -07003000 ---help---
3001 PLIP (Parallel Line Internet Protocol) is used to create a
3002 reasonably fast mini network consisting of two (or, rarely, more)
3003 local machines. A PLIP link from a Linux box is a popular means to
3004 install a Linux distribution on a machine which doesn't have a
3005 CD-ROM drive (a minimal system has to be transferred with floppies
3006 first). The kernels on both machines need to have this PLIP option
3007 enabled for this to work.
3008
3009 The PLIP driver has two modes, mode 0 and mode 1. The parallel
3010 ports (the connectors at the computers with 25 holes) are connected
3011 with "null printer" or "Turbo Laplink" cables which can transmit 4
3012 bits at a time (mode 0) or with special PLIP cables, to be used on
3013 bidirectional parallel ports only, which can transmit 8 bits at a
3014 time (mode 1); you can find the wiring of these cables in
3015 <file:Documentation/networking/PLIP.txt>. The cables can be up to
3016 15m long. Mode 0 works also if one of the machines runs DOS/Windows
3017 and has some PLIP software installed, e.g. the Crynwr PLIP packet
3018 driver (<http://oak.oakland.edu/simtel.net/msdos/pktdrvr-pre.html>)
3019 and winsock or NCSA's telnet.
3020
3021 If you want to use PLIP, say Y and read the PLIP mini-HOWTO as well
3022 as the NET-3-HOWTO, both available from
3023 <http://www.tldp.org/docs.html#howto>. Note that the PLIP
3024 protocol has been changed and this PLIP driver won't work together
3025 with the PLIP support in Linux versions 1.0.x. This option enlarges
3026 your kernel by about 8 KB.
3027
Adrian Bunk57ce45d2007-11-12 21:03:58 -08003028 To compile this driver as a module, choose M here. The module
3029 will be called plip. If unsure, say Y or M, in case you buy
3030 a laptop later.
Linus Torvalds1da177e2005-04-16 15:20:36 -07003031
3032config PPP
3033 tristate "PPP (point-to-point protocol) support"
Ralf Baechleb6e37e52006-07-14 12:15:40 +01003034 select SLHC
Linus Torvalds1da177e2005-04-16 15:20:36 -07003035 ---help---
3036 PPP (Point to Point Protocol) is a newer and better SLIP. It serves
3037 the same purpose: sending Internet traffic over telephone (and other
3038 serial) lines. Ask your access provider if they support it, because
3039 otherwise you can't use it; most Internet access providers these
3040 days support PPP rather than SLIP.
3041
3042 To use PPP, you need an additional program called pppd as described
3043 in the PPP-HOWTO, available at
3044 <http://www.tldp.org/docs.html#howto>. Make sure that you have
3045 the version of pppd recommended in <file:Documentation/Changes>.
3046 The PPP option enlarges your kernel by about 16 KB.
3047
3048 There are actually two versions of PPP: the traditional PPP for
3049 asynchronous lines, such as regular analog phone lines, and
3050 synchronous PPP which can be used over digital ISDN lines for
3051 example. If you want to use PPP over phone lines or other
3052 asynchronous serial lines, you need to say Y (or M) here and also to
3053 the next option, "PPP support for async serial ports". For PPP over
3054 synchronous lines, you should say Y (or M) here and to "Support
3055 synchronous PPP", below.
3056
3057 If you said Y to "Version information on all symbols" above, then
3058 you cannot compile the PPP driver into the kernel; you can then only
3059 compile it as a module. To compile this driver as a module, choose M
Adrian Bunk57ce45d2007-11-12 21:03:58 -08003060 here. The module will be called ppp_generic.
Linus Torvalds1da177e2005-04-16 15:20:36 -07003061
3062config PPP_MULTILINK
3063 bool "PPP multilink support (EXPERIMENTAL)"
3064 depends on PPP && EXPERIMENTAL
3065 help
3066 PPP multilink is a protocol (defined in RFC 1990) which allows you
3067 to combine several (logical or physical) lines into one logical PPP
3068 connection, so that you can utilize your full bandwidth.
3069
3070 This has to be supported at the other end as well and you need a
3071 version of the pppd daemon which understands the multilink protocol.
3072
3073 If unsure, say N.
3074
3075config PPP_FILTER
3076 bool "PPP filtering"
3077 depends on PPP
3078 help
3079 Say Y here if you want to be able to filter the packets passing over
3080 PPP interfaces. This allows you to control which packets count as
3081 activity (i.e. which packets will reset the idle timer or bring up
Jon Mason47c51432006-02-12 11:53:04 -06003082 a demand-dialed link) and which packets are to be dropped entirely.
Linus Torvalds1da177e2005-04-16 15:20:36 -07003083 You need to say Y here if you wish to use the pass-filter and
3084 active-filter options to pppd.
3085
3086 If unsure, say N.
3087
3088config PPP_ASYNC
3089 tristate "PPP support for async serial ports"
3090 depends on PPP
3091 select CRC_CCITT
3092 ---help---
3093 Say Y (or M) here if you want to be able to use PPP over standard
3094 asynchronous serial ports, such as COM1 or COM2 on a PC. If you use
3095 a modem (not a synchronous or ISDN modem) to contact your ISP, you
3096 need this option.
3097
3098 To compile this driver as a module, choose M here.
3099
3100 If unsure, say Y.
3101
3102config PPP_SYNC_TTY
3103 tristate "PPP support for sync tty ports"
3104 depends on PPP
3105 help
3106 Say Y (or M) here if you want to be able to use PPP over synchronous
3107 (HDLC) tty devices, such as the SyncLink adapter. These devices
3108 are often used for high-speed leased lines like T1/E1.
3109
3110 To compile this driver as a module, choose M here.
3111
3112config PPP_DEFLATE
3113 tristate "PPP Deflate compression"
3114 depends on PPP
3115 select ZLIB_INFLATE
3116 select ZLIB_DEFLATE
3117 ---help---
3118 Support for the Deflate compression method for PPP, which uses the
3119 Deflate algorithm (the same algorithm that gzip uses) to compress
3120 each PPP packet before it is sent over the wire. The machine at the
3121 other end of the PPP link (usually your ISP) has to support the
3122 Deflate compression method as well for this to be useful. Even if
3123 they don't support it, it is safe to say Y here.
3124
3125 To compile this driver as a module, choose M here.
3126
3127config PPP_BSDCOMP
3128 tristate "PPP BSD-Compress compression"
3129 depends on PPP
3130 ---help---
3131 Support for the BSD-Compress compression method for PPP, which uses
3132 the LZW compression method to compress each PPP packet before it is
3133 sent over the wire. The machine at the other end of the PPP link
3134 (usually your ISP) has to support the BSD-Compress compression
3135 method as well for this to be useful. Even if they don't support it,
3136 it is safe to say Y here.
3137
3138 The PPP Deflate compression method ("PPP Deflate compression",
3139 above) is preferable to BSD-Compress, because it compresses better
3140 and is patent-free.
3141
3142 Note that the BSD compression code will always be compiled as a
3143 module; it is called bsd_comp and will show up in the directory
3144 modules once you have said "make modules". If unsure, say N.
3145
Matt Domschb3f9b922005-11-08 09:40:47 -08003146config PPP_MPPE
3147 tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)"
3148 depends on PPP && EXPERIMENTAL
3149 select CRYPTO
3150 select CRYPTO_SHA1
3151 select CRYPTO_ARC4
Patrick McHardybcbaecb2006-10-25 16:49:36 +10003152 select CRYPTO_ECB
Matt Domschb3f9b922005-11-08 09:40:47 -08003153 ---help---
3154 Support for the MPPE Encryption protocol, as employed by the
3155 Microsoft Point-to-Point Tunneling Protocol.
3156
3157 See http://pptpclient.sourceforge.net/ for information on
3158 configuring PPTP clients and servers to utilize this method.
3159
Linus Torvalds1da177e2005-04-16 15:20:36 -07003160config PPPOE
3161 tristate "PPP over Ethernet (EXPERIMENTAL)"
3162 depends on EXPERIMENTAL && PPP
3163 help
3164 Support for PPP over Ethernet.
3165
3166 This driver requires the latest version of pppd from the CVS
3167 repository at cvs.samba.org. Alternatively, see the
3168 RoaringPenguin package (<http://www.roaringpenguin.com/pppoe>)
3169 which contains instruction on how to use this driver (under
3170 the heading "Kernel mode PPPoE").
3171
3172config PPPOATM
3173 tristate "PPP over ATM"
3174 depends on ATM && PPP
3175 help
3176 Support PPP (Point to Point Protocol) encapsulated in ATM frames.
3177 This implementation does not yet comply with section 8 of RFC2364,
3178 which can lead to bad results if the ATM peer loses state and
3179 changes its encapsulation unilaterally.
3180
James Chapman3557baa2007-06-27 15:49:24 -07003181config PPPOL2TP
3182 tristate "PPP over L2TP (EXPERIMENTAL)"
James Chapman143cf352007-07-30 18:51:48 -07003183 depends on EXPERIMENTAL && PPP && INET
James Chapman3557baa2007-06-27 15:49:24 -07003184 help
3185 Support for PPP-over-L2TP socket family. L2TP is a protocol
3186 used by ISPs and enterprises to tunnel PPP traffic over UDP
3187 tunnels. L2TP is replacing PPTP for VPN uses.
3188
3189 This kernel component handles only L2TP data packets: a
3190 userland daemon handles L2TP the control protocol (tunnel
3191 and session setup). One such daemon is OpenL2TP
3192 (http://openl2tp.sourceforge.net/).
3193
Linus Torvalds1da177e2005-04-16 15:20:36 -07003194config SLIP
3195 tristate "SLIP (serial line) support"
Linus Torvalds1da177e2005-04-16 15:20:36 -07003196 ---help---
3197 Say Y if you intend to use SLIP or CSLIP (compressed SLIP) to
3198 connect to your Internet service provider or to connect to some
3199 other local Unix box or if you want to configure your Linux box as a
3200 Slip/CSlip server for other people to dial in. SLIP (Serial Line
3201 Internet Protocol) is a protocol used to send Internet traffic over
3202 serial connections such as telephone lines or null modem cables;
3203 nowadays, the protocol PPP is more commonly used for this same
3204 purpose.
3205
3206 Normally, your access provider has to support SLIP in order for you
3207 to be able to use it, but there is now a SLIP emulator called SLiRP
3208 around (available from
3209 <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
3210 allows you to use SLIP over a regular dial up shell connection. If
3211 you plan to use SLiRP, make sure to say Y to CSLIP, below. The
3212 NET-3-HOWTO, available from
3213 <http://www.tldp.org/docs.html#howto>, explains how to
3214 configure SLIP. Note that you don't need this option if you just
3215 want to run term (term is a program which gives you almost full
3216 Internet connectivity if you have a regular dial up shell account on
3217 some Internet connected Unix computer. Read
3218 <http://www.bart.nl/~patrickr/term-howto/Term-HOWTO.html>). SLIP
3219 support will enlarge your kernel by about 4 KB. If unsure, say N.
3220
Adrian Bunk57ce45d2007-11-12 21:03:58 -08003221 To compile this driver as a module, choose M here. The module
3222 will be called slip.
Linus Torvalds1da177e2005-04-16 15:20:36 -07003223
3224config SLIP_COMPRESSED
3225 bool "CSLIP compressed headers"
3226 depends on SLIP
Ralf Baechleb6e37e52006-07-14 12:15:40 +01003227 select SLHC
Linus Torvalds1da177e2005-04-16 15:20:36 -07003228 ---help---
3229 This protocol is faster than SLIP because it uses compression on the
3230 TCP/IP headers (not on the data itself), but it has to be supported
3231 on both ends. Ask your access provider if you are not sure and
3232 answer Y, just in case. You will still be able to use plain SLIP. If
3233 you plan to use SLiRP, the SLIP emulator (available from
3234 <ftp://ibiblio.org/pub/Linux/system/network/serial/>) which
3235 allows you to use SLIP over a regular dial up shell connection, you
3236 definitely want to say Y here. The NET-3-HOWTO, available from
3237 <http://www.tldp.org/docs.html#howto>, explains how to configure
3238 CSLIP. This won't enlarge your kernel.
3239
Ralf Baechleb6e37e52006-07-14 12:15:40 +01003240config SLHC
3241 tristate
3242 help
3243 This option enables Van Jacobsen serial line header compression
3244 routines.
3245
Linus Torvalds1da177e2005-04-16 15:20:36 -07003246config SLIP_SMART
3247 bool "Keepalive and linefill"
3248 depends on SLIP
3249 help
3250 Adds additional capabilities to the SLIP driver to support the
3251 RELCOM line fill and keepalive monitoring. Ideal on poor quality
3252 analogue lines.
3253
3254config SLIP_MODE_SLIP6
3255 bool "Six bit SLIP encapsulation"
3256 depends on SLIP
3257 help
3258 Just occasionally you may need to run IP over hostile serial
3259 networks that don't pass all control characters or are only seven
3260 bit. Saying Y here adds an extra mode you can use with SLIP:
3261 "slip6". In this mode, SLIP will only send normal ASCII symbols over
3262 the serial device. Naturally, this has to be supported at the other
3263 end of the link as well. It's good enough, for example, to run IP
3264 over the async ports of a Camtec JNT Pad. If unsure, say N.
3265
3266config NET_FC
3267 bool "Fibre Channel driver support"
Randy Dunlapcbcd2a42005-07-27 13:04:35 -07003268 depends on SCSI && PCI
Linus Torvalds1da177e2005-04-16 15:20:36 -07003269 help
3270 Fibre Channel is a high speed serial protocol mainly used to connect
3271 large storage devices to the computer; it is compatible with and
3272 intended to replace SCSI.
3273
3274 If you intend to use Fibre Channel, you need to have a Fibre channel
3275 adaptor card in your computer; say Y here and to the driver for your
3276 adaptor below. You also should have said Y to "SCSI support" and
3277 "SCSI generic support".
3278
Linus Torvalds1da177e2005-04-16 15:20:36 -07003279config NETCONSOLE
3280 tristate "Network console logging support (EXPERIMENTAL)"
Matt Mackall5e43db72005-07-27 15:24:42 -07003281 depends on EXPERIMENTAL
Linus Torvalds1da177e2005-04-16 15:20:36 -07003282 ---help---
3283 If you want to log kernel messages over the network, enable this.
3284 See <file:Documentation/networking/netconsole.txt> for details.
3285
Satyam Sharma0bcc1812007-08-10 15:35:05 -07003286config NETCONSOLE_DYNAMIC
3287 bool "Dynamic reconfiguration of logging targets (EXPERIMENTAL)"
3288 depends on NETCONSOLE && SYSFS && EXPERIMENTAL
3289 select CONFIGFS_FS
3290 help
3291 This option enables the ability to dynamically reconfigure target
3292 parameters (interface, IP addresses, port numbers, MAC addresses)
3293 at runtime through a userspace interface exported using configfs.
3294 See <file:Documentation/networking/netconsole.txt> for details.
3295
Randy Dunlap54208992005-07-18 13:45:12 -07003296config NETPOLL
3297 def_bool NETCONSOLE
3298
Randy Dunlap54208992005-07-18 13:45:12 -07003299config NETPOLL_TRAP
3300 bool "Netpoll traffic trapping"
3301 default n
3302 depends on NETPOLL
3303
3304config NET_POLL_CONTROLLER
3305 def_bool NETPOLL
3306
Rusty Russell296f96f2007-10-22 11:03:37 +10003307config VIRTIO_NET
3308 tristate "Virtio network driver (EXPERIMENTAL)"
3309 depends on EXPERIMENTAL && VIRTIO
3310 ---help---
Anthony Liguori0ad07ec2007-11-07 20:46:31 -06003311 This is the virtual network driver for virtio. It can be used with
3312 lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
Rusty Russell296f96f2007-10-22 11:03:37 +10003313
Shreyas Bhatewarad1a890f2009-10-13 00:15:51 -07003314config VMXNET3
3315 tristate "VMware VMXNET3 ethernet driver"
Shreyas Bhatewara115924b2009-11-16 13:41:33 +00003316 depends on PCI && INET
Shreyas Bhatewarad1a890f2009-10-13 00:15:51 -07003317 help
3318 This driver supports VMware's vmxnet3 virtual ethernet NIC.
3319 To compile this driver as a module, choose M here: the
3320 module will be called vmxnet3.
3321
Jan Engelhardtd1c0a652007-06-13 12:48:53 -07003322endif # NETDEVICES