blob: e74ce4c4e6dc228cf4c3d25ed9a7e43977504992 [file] [log] [blame]
wdenkc6097192002-11-03 00:24:07 +00001#
wdenk151ab832005-02-24 22:44:16 +00002# (C) Copyright 2000 - 2005
wdenkc6097192002-11-03 00:24:07 +00003# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
4#
5# See file CREDITS for list of people who contributed to this
6# project.
7#
8# This program is free software; you can redistribute it and/or
9# modify it under the terms of the GNU General Public License as
10# published by the Free Software Foundation; either version 2 of
11# the License, or (at your option) any later version.
12#
13# This program is distributed in the hope that it will be useful,
14# but WITHOUT ANY WARRANTY; without even the implied warranty of
15# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16# GNU General Public License for more details.
17#
18# You should have received a copy of the GNU General Public License
19# along with this program; if not, write to the Free Software
20# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
21# MA 02111-1307 USA
22#
23
24Summary:
25========
26
wdenk24ee89b2002-11-03 17:56:27 +000027This directory contains the source code for U-Boot, a boot loader for
wdenke86e5a02004-10-17 21:12:06 +000028Embedded boards based on PowerPC, ARM, MIPS and several other
29processors, which can be installed in a boot ROM and used to
30initialize and test the hardware or to download and run application
31code.
wdenkc6097192002-11-03 00:24:07 +000032
33The development of U-Boot is closely related to Linux: some parts of
wdenk24ee89b2002-11-03 17:56:27 +000034the source code originate in the Linux source tree, we have some
35header files in common, and special provision has been made to
wdenkc6097192002-11-03 00:24:07 +000036support booting of Linux images.
37
38Some attention has been paid to make this software easily
39configurable and extendable. For instance, all monitor commands are
40implemented with the same call interface, so that it's very easy to
41add new commands. Also, instead of permanently adding rarely used
42code (for instance hardware test utilities) to the monitor, you can
43load and run it dynamically.
44
45
46Status:
47=======
48
49In general, all boards for which a configuration option exists in the
wdenk24ee89b2002-11-03 17:56:27 +000050Makefile have been tested to some extent and can be considered
wdenkc6097192002-11-03 00:24:07 +000051"working". In fact, many of them are used in production systems.
52
wdenk24ee89b2002-11-03 17:56:27 +000053In case of problems see the CHANGELOG and CREDITS files to find out
wdenkc6097192002-11-03 00:24:07 +000054who contributed the specific port.
55
wdenkc6097192002-11-03 00:24:07 +000056
57Where to get help:
58==================
59
wdenk24ee89b2002-11-03 17:56:27 +000060In case you have questions about, problems with or contributions for
61U-Boot you should send a message to the U-Boot mailing list at
62<u-boot-users@lists.sourceforge.net>. There is also an archive of
63previous traffic on the mailing list - please search the archive
wdenkc6097192002-11-03 00:24:07 +000064before asking FAQ's. Please see
65http://lists.sourceforge.net/lists/listinfo/u-boot-users/
66
67
68Where we come from:
69===================
70
71- start from 8xxrom sources
wdenk24ee89b2002-11-03 17:56:27 +000072- create PPCBoot project (http://sourceforge.net/projects/ppcboot)
wdenkc6097192002-11-03 00:24:07 +000073- clean up code
74- make it easier to add custom boards
75- make it possible to add other [PowerPC] CPUs
76- extend functions, especially:
77 * Provide extended interface to Linux boot loader
78 * S-Record download
79 * network boot
80 * PCMCIA / CompactFLash / ATA disk / SCSI ... boot
wdenk24ee89b2002-11-03 17:56:27 +000081- create ARMBoot project (http://sourceforge.net/projects/armboot)
wdenkc6097192002-11-03 00:24:07 +000082- add other CPU families (starting with ARM)
wdenk24ee89b2002-11-03 17:56:27 +000083- create U-Boot project (http://sourceforge.net/projects/u-boot)
84
85
86Names and Spelling:
87===================
88
89The "official" name of this project is "Das U-Boot". The spelling
90"U-Boot" shall be used in all written text (documentation, comments
91in source files etc.). Example:
92
93 This is the README file for the U-Boot project.
94
95File names etc. shall be based on the string "u-boot". Examples:
96
97 include/asm-ppc/u-boot.h
98
99 #include <asm/u-boot.h>
100
101Variable names, preprocessor constants etc. shall be either based on
102the string "u_boot" or on "U_BOOT". Example:
103
104 U_BOOT_VERSION u_boot_logo
105 IH_OS_U_BOOT u_boot_hush_start
wdenkc6097192002-11-03 00:24:07 +0000106
107
wdenk93f19cc2002-12-17 17:55:09 +0000108Versioning:
109===========
110
111U-Boot uses a 3 level version number containing a version, a
112sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
113sub-version "34", and patchlevel "4".
114
115The patchlevel is used to indicate certain stages of development
116between released versions, i. e. officially released versions of
117U-Boot will always have a patchlevel of "0".
118
119
wdenkc6097192002-11-03 00:24:07 +0000120Directory Hierarchy:
121====================
122
wdenk7152b1d2003-09-05 23:19:14 +0000123- board Board dependent files
124- common Misc architecture independent functions
wdenkc6097192002-11-03 00:24:07 +0000125- cpu CPU specific files
wdenk983fda82004-10-28 00:09:35 +0000126 - 74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
wdenk11dadd52004-02-27 00:07:27 +0000127 - arm720t Files specific to ARM 720 CPUs
128 - arm920t Files specific to ARM 920 CPUs
wdenk983fda82004-10-28 00:09:35 +0000129 - imx Files specific to Freescale MC9328 i.MX CPUs
wdenk1d9f4102004-10-09 22:21:29 +0000130 - s3c24x0 Files specific to Samsung S3C24X0 CPUs
wdenk11dadd52004-02-27 00:07:27 +0000131 - arm925t Files specific to ARM 925 CPUs
132 - arm926ejs Files specific to ARM 926 CPUs
wdenk8ed96042005-01-09 23:16:25 +0000133 - arm1136 Files specific to ARM 1136 CPUs
wdenk11dadd52004-02-27 00:07:27 +0000134 - at91rm9200 Files specific to Atmel AT91RM9200 CPUs
135 - i386 Files specific to i386 CPUs
136 - ixp Files specific to Intel XScale IXP CPUs
wdenk983fda82004-10-28 00:09:35 +0000137 - mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
wdenk11dadd52004-02-27 00:07:27 +0000138 - mips Files specific to MIPS CPUs
wdenk983fda82004-10-28 00:09:35 +0000139 - mpc5xx Files specific to Freescale MPC5xx CPUs
140 - mpc5xxx Files specific to Freescale MPC5xxx CPUs
141 - mpc8xx Files specific to Freescale MPC8xx CPUs
142 - mpc8220 Files specific to Freescale MPC8220 CPUs
143 - mpc824x Files specific to Freescale MPC824x CPUs
144 - mpc8260 Files specific to Freescale MPC8260 CPUs
145 - mpc85xx Files specific to Freescale MPC85xx CPUs
wdenk11dadd52004-02-27 00:07:27 +0000146 - nios Files specific to Altera NIOS CPUs
wdenk5c952cf2004-10-10 21:27:30 +0000147 - nios2 Files specific to Altera Nios-II CPUs
wdenk11dadd52004-02-27 00:07:27 +0000148 - ppc4xx Files specific to IBM PowerPC 4xx CPUs
149 - pxa Files specific to Intel XScale PXA CPUs
150 - s3c44b0 Files specific to Samsung S3C44B0 CPUs
151 - sa1100 Files specific to Intel StrongARM SA1100 CPUs
wdenkc6097192002-11-03 00:24:07 +0000152- disk Code for disk drive partition handling
153- doc Documentation (don't expect too much)
wdenk7152b1d2003-09-05 23:19:14 +0000154- drivers Commonly used device drivers
wdenkc6097192002-11-03 00:24:07 +0000155- dtt Digital Thermometer and Thermostat drivers
156- examples Example code for standalone applications, etc.
157- include Header Files
wdenk11dadd52004-02-27 00:07:27 +0000158- lib_arm Files generic to ARM architecture
159- lib_generic Files generic to all architectures
160- lib_i386 Files generic to i386 architecture
161- lib_m68k Files generic to m68k architecture
162- lib_mips Files generic to MIPS architecture
163- lib_nios Files generic to NIOS architecture
164- lib_ppc Files generic to PowerPC architecture
wdenkc6097192002-11-03 00:24:07 +0000165- net Networking code
wdenkc6097192002-11-03 00:24:07 +0000166- post Power On Self Test
wdenkc6097192002-11-03 00:24:07 +0000167- rtc Real Time Clock drivers
168- tools Tools to build S-Record or U-Boot images, etc.
169
wdenkc6097192002-11-03 00:24:07 +0000170Software Configuration:
171=======================
172
173Configuration is usually done using C preprocessor defines; the
174rationale behind that is to avoid dead code whenever possible.
175
176There are two classes of configuration variables:
177
178* Configuration _OPTIONS_:
179 These are selectable by the user and have names beginning with
180 "CONFIG_".
181
182* Configuration _SETTINGS_:
183 These depend on the hardware etc. and should not be meddled with if
184 you don't know what you're doing; they have names beginning with
185 "CFG_".
186
187Later we will add a configuration tool - probably similar to or even
188identical to what's used for the Linux kernel. Right now, we have to
189do the configuration by hand, which means creating some symbolic
190links and editing some configuration files. We use the TQM8xxL boards
191as an example here.
192
193
194Selection of Processor Architecture and Board Type:
195---------------------------------------------------
196
197For all supported boards there are ready-to-use default
198configurations available; just type "make <board_name>_config".
199
200Example: For a TQM823L module type:
201
202 cd u-boot
203 make TQM823L_config
204
205For the Cogent platform, you need to specify the cpu type as well;
206e.g. "make cogent_mpc8xx_config". And also configure the cogent
207directory according to the instructions in cogent/README.
208
209
210Configuration Options:
211----------------------
212
213Configuration depends on the combination of board and CPU type; all
214such information is kept in a configuration file
215"include/configs/<board_name>.h".
216
217Example: For a TQM823L module, all configuration settings are in
218"include/configs/TQM823L.h".
219
220
wdenk7f6c2cb2002-11-10 22:06:23 +0000221Many of the options are named exactly as the corresponding Linux
222kernel configuration options. The intention is to make it easier to
223build a config tool - later.
224
225
wdenkc6097192002-11-03 00:24:07 +0000226The following options need to be configured:
227
228- CPU Type: Define exactly one of
229
230 PowerPC based CPUs:
231 -------------------
232 CONFIG_MPC823, CONFIG_MPC850, CONFIG_MPC855, CONFIG_MPC860
wdenk0db5bca2003-03-31 17:27:09 +0000233 or CONFIG_MPC5xx
wdenk983fda82004-10-28 00:09:35 +0000234 or CONFIG_MPC8220
wdenkc6097192002-11-03 00:24:07 +0000235 or CONFIG_MPC824X, CONFIG_MPC8260
wdenk42d1f032003-10-15 23:53:47 +0000236 or CONFIG_MPC85xx
wdenkc6097192002-11-03 00:24:07 +0000237 or CONFIG_IOP480
238 or CONFIG_405GP
wdenk12f34242003-09-02 22:48:03 +0000239 or CONFIG_405EP
wdenkc6097192002-11-03 00:24:07 +0000240 or CONFIG_440
241 or CONFIG_MPC74xx
wdenk72755c72003-06-20 23:10:58 +0000242 or CONFIG_750FX
wdenkc6097192002-11-03 00:24:07 +0000243
244 ARM based CPUs:
245 ---------------
246 CONFIG_SA1110
247 CONFIG_ARM7
248 CONFIG_PXA250
249
wdenk507bbe32004-04-18 21:13:41 +0000250 MicroBlaze based CPUs:
251 ----------------------
wdenk857cad32004-07-10 23:48:41 +0000252 CONFIG_MICROBLAZE
wdenk507bbe32004-04-18 21:13:41 +0000253
wdenk5c952cf2004-10-10 21:27:30 +0000254 Nios-2 based CPUs:
255 ----------------------
256 CONFIG_NIOS2
257
wdenkc6097192002-11-03 00:24:07 +0000258
259- Board Type: Define exactly one of
260
261 PowerPC based boards:
262 ---------------------
263
wdenk17ea1172004-06-06 21:51:03 +0000264 CONFIG_ADCIOP CONFIG_GEN860T CONFIG_PCI405
265 CONFIG_ADS860 CONFIG_GENIETV CONFIG_PCIPPC2
266 CONFIG_AMX860 CONFIG_GTH CONFIG_PCIPPC6
267 CONFIG_AR405 CONFIG_gw8260 CONFIG_pcu_e
268 CONFIG_BAB7xx CONFIG_hermes CONFIG_PIP405
269 CONFIG_c2mon CONFIG_hymod CONFIG_PM826
270 CONFIG_CANBT CONFIG_IAD210 CONFIG_ppmc8260
271 CONFIG_CCM CONFIG_ICU862 CONFIG_QS823
272 CONFIG_CMI CONFIG_IP860 CONFIG_QS850
273 CONFIG_cogent_mpc8260 CONFIG_IPHASE4539 CONFIG_QS860T
274 CONFIG_cogent_mpc8xx CONFIG_IVML24 CONFIG_RBC823
275 CONFIG_CPCI405 CONFIG_IVML24_128 CONFIG_RPXClassic
276 CONFIG_CPCI4052 CONFIG_IVML24_256 CONFIG_RPXlite
277 CONFIG_CPCIISER4 CONFIG_IVMS8 CONFIG_RPXsuper
278 CONFIG_CPU86 CONFIG_IVMS8_128 CONFIG_rsdproto
279 CONFIG_CRAYL1 CONFIG_IVMS8_256 CONFIG_sacsng
280 CONFIG_CSB272 CONFIG_JSE CONFIG_Sandpoint8240
281 CONFIG_CU824 CONFIG_LANTEC CONFIG_Sandpoint8245
282 CONFIG_DASA_SIM CONFIG_lwmon CONFIG_sbc8260
wdenk8b07a112004-07-10 21:45:47 +0000283 CONFIG_DB64360 CONFIG_MBX CONFIG_sbc8560
284 CONFIG_DB64460 CONFIG_MBX860T CONFIG_SM850
285 CONFIG_DU405 CONFIG_MHPC CONFIG_SPD823TS
286 CONFIG_DUET_ADS CONFIG_MIP405 CONFIG_STXGP3
287 CONFIG_EBONY CONFIG_MOUSSE CONFIG_SXNI855T
288 CONFIG_ELPPC CONFIG_MPC8260ADS CONFIG_TQM823L
289 CONFIG_ELPT860 CONFIG_MPC8540ADS CONFIG_TQM8260
290 CONFIG_ep8260 CONFIG_MPC8560ADS CONFIG_TQM850L
291 CONFIG_ERIC CONFIG_MUSENKI CONFIG_TQM855L
292 CONFIG_ESTEEM192E CONFIG_MVS1 CONFIG_TQM860L
293 CONFIG_ETX094 CONFIG_NETPHONE CONFIG_TTTech
294 CONFIG_EVB64260 CONFIG_NETTA CONFIG_UTX8245
295 CONFIG_FADS823 CONFIG_NETVIA CONFIG_V37
296 CONFIG_FADS850SAR CONFIG_NX823 CONFIG_W7OLMC
297 CONFIG_FADS860T CONFIG_OCRTC CONFIG_W7OLMG
298 CONFIG_FLAGADM CONFIG_ORSG CONFIG_WALNUT405
299 CONFIG_FPS850L CONFIG_OXC CONFIG_ZPC1900
300 CONFIG_FPS860L CONFIG_ZUMA
wdenkc6097192002-11-03 00:24:07 +0000301
302 ARM based boards:
303 -----------------
304
wdenk8ed96042005-01-09 23:16:25 +0000305 CONFIG_AT91RM9200DK, CONFIG_CERF250, CONFIG_DNP1110,
306 CONFIG_EP7312, CONFIG_H2_OMAP1610, CONFIG_HHP_CRADLE,
307 CONFIG_IMPA7, CONFIG_INNOVATOROMAP1510, CONFIG_INNOVATOROMAP1610,
308 CONFIG_LART, CONFIG_LPD7A400 CONFIG_LUBBOCK,
309 CONFIG_OSK_OMAP5912, CONFIG_OMAP2420H4, CONFIG_SHANNON,
310 CONFIG_P2_OMAP730, CONFIG_SMDK2400, CONFIG_SMDK2410,
311 CONFIG_TRAB, CONFIG_VCMA9
wdenkc6097192002-11-03 00:24:07 +0000312
wdenk507bbe32004-04-18 21:13:41 +0000313 MicroBlaze based boards:
314 ------------------------
315
316 CONFIG_SUZAKU
317
wdenk5c952cf2004-10-10 21:27:30 +0000318 Nios-2 based boards:
319 ------------------------
320
321 CONFIG_PCI5441 CONFIG_PK1C20
322
wdenkc6097192002-11-03 00:24:07 +0000323
324- CPU Module Type: (if CONFIG_COGENT is defined)
325 Define exactly one of
326 CONFIG_CMA286_60_OLD
327--- FIXME --- not tested yet:
328 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
329 CONFIG_CMA287_23, CONFIG_CMA287_50
330
331- Motherboard Type: (if CONFIG_COGENT is defined)
332 Define exactly one of
333 CONFIG_CMA101, CONFIG_CMA102
334
335- Motherboard I/O Modules: (if CONFIG_COGENT is defined)
336 Define one or more of
337 CONFIG_CMA302
338
339- Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
340 Define one or more of
341 CONFIG_LCD_HEARTBEAT - update a character position on
342 the lcd display every second with
343 a "rotator" |\-/|\-/
344
wdenk2535d602003-07-17 23:16:40 +0000345- Board flavour: (if CONFIG_MPC8260ADS is defined)
346 CONFIG_ADSTYPE
347 Possible values are:
348 CFG_8260ADS - original MPC8260ADS
wdenk180d3f72004-01-04 16:28:35 +0000349 CFG_8266ADS - MPC8266ADS
wdenk54387ac2003-10-08 22:45:44 +0000350 CFG_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
wdenk04a85b32004-04-15 18:22:41 +0000351 CFG_8272ADS - MPC8272ADS
wdenk2535d602003-07-17 23:16:40 +0000352
wdenkc6097192002-11-03 00:24:07 +0000353- MPC824X Family Member (if CONFIG_MPC824X is defined)
wdenk5da627a2003-10-09 20:09:04 +0000354 Define exactly one of
355 CONFIG_MPC8240, CONFIG_MPC8245
wdenkc6097192002-11-03 00:24:07 +0000356
wdenk75d1ea72004-01-31 20:06:54 +0000357- 8xx CPU Options: (if using an MPC8xx cpu)
wdenk66ca92a2004-09-28 17:59:53 +0000358 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
359 get_gclk_freq() cannot work
wdenk5da627a2003-10-09 20:09:04 +0000360 e.g. if there is no 32KHz
361 reference PIT/RTC clock
wdenk66ca92a2004-09-28 17:59:53 +0000362 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
363 or XTAL/EXTAL)
wdenkc6097192002-11-03 00:24:07 +0000364
wdenk66ca92a2004-09-28 17:59:53 +0000365- 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
366 CFG_8xx_CPUCLK_MIN
367 CFG_8xx_CPUCLK_MAX
368 CONFIG_8xx_CPUCLK_DEFAULT
wdenk75d1ea72004-01-31 20:06:54 +0000369 See doc/README.MPC866
370
371 CFG_MEASURE_CPUCLK
372
wdenkba56f622004-02-06 23:19:44 +0000373 Define this to measure the actual CPU clock instead
374 of relying on the correctness of the configured
375 values. Mostly useful for board bringup to make sure
376 the PLL is locked at the intended frequency. Note
377 that this requires a (stable) reference clock (32 kHz
wdenk66ca92a2004-09-28 17:59:53 +0000378 RTC clock or CFG_8XX_XIN)
wdenk75d1ea72004-01-31 20:06:54 +0000379
wdenk5da627a2003-10-09 20:09:04 +0000380- Linux Kernel Interface:
wdenkc6097192002-11-03 00:24:07 +0000381 CONFIG_CLOCKS_IN_MHZ
382
383 U-Boot stores all clock information in Hz
384 internally. For binary compatibility with older Linux
385 kernels (which expect the clocks passed in the
386 bd_info data to be in MHz) the environment variable
387 "clocks_in_mhz" can be defined so that U-Boot
388 converts clock data to MHZ before passing it to the
389 Linux kernel.
wdenkc6097192002-11-03 00:24:07 +0000390 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
391 "clocks_in_mhz=1" is automatically included in the
392 default environment.
393
wdenk5da627a2003-10-09 20:09:04 +0000394 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
395
396 When transfering memsize parameter to linux, some versions
397 expect it to be in bytes, others in MB.
398 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
399
wdenk6705d812004-08-02 23:22:59 +0000400- Serial Ports:
401 CFG_PL010_SERIAL
402
403 Define this if you want support for Amba PrimeCell PL010 UARTs.
404
405 CFG_PL011_SERIAL
406
407 Define this if you want support for Amba PrimeCell PL011 UARTs.
408
409 CONFIG_PL011_CLOCK
410
411 If you have Amba PrimeCell PL011 UARTs, set this variable to
412 the clock speed of the UARTs.
413
414 CONFIG_PL01x_PORTS
415
416 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
417 define this to a list of base addresses for each (supported)
418 port. See e.g. include/configs/versatile.h
419
420
wdenkc6097192002-11-03 00:24:07 +0000421- Console Interface:
wdenk43d96162003-03-06 00:02:04 +0000422 Depending on board, define exactly one serial port
423 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
424 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
425 console by defining CONFIG_8xx_CONS_NONE
wdenkc6097192002-11-03 00:24:07 +0000426
427 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
428 port routines must be defined elsewhere
429 (i.e. serial_init(), serial_getc(), ...)
430
431 CONFIG_CFB_CONSOLE
432 Enables console device for a color framebuffer. Needs following
433 defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
434 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
435 (default big endian)
436 VIDEO_HW_RECTFILL graphic chip supports
437 rectangle fill
438 (cf. smiLynxEM)
439 VIDEO_HW_BITBLT graphic chip supports
440 bit-blit (cf. smiLynxEM)
441 VIDEO_VISIBLE_COLS visible pixel columns
442 (cols=pitch)
wdenkba56f622004-02-06 23:19:44 +0000443 VIDEO_VISIBLE_ROWS visible pixel rows
444 VIDEO_PIXEL_SIZE bytes per pixel
wdenkc6097192002-11-03 00:24:07 +0000445 VIDEO_DATA_FORMAT graphic data format
446 (0-5, cf. cfb_console.c)
wdenkba56f622004-02-06 23:19:44 +0000447 VIDEO_FB_ADRS framebuffer address
wdenkc6097192002-11-03 00:24:07 +0000448 VIDEO_KBD_INIT_FCT keyboard int fct
449 (i.e. i8042_kbd_init())
450 VIDEO_TSTC_FCT test char fct
451 (i.e. i8042_tstc)
452 VIDEO_GETC_FCT get char fct
453 (i.e. i8042_getc)
454 CONFIG_CONSOLE_CURSOR cursor drawing on/off
455 (requires blink timer
456 cf. i8042.c)
457 CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
458 CONFIG_CONSOLE_TIME display time/date info in
459 upper right corner
460 (requires CFG_CMD_DATE)
461 CONFIG_VIDEO_LOGO display Linux logo in
462 upper left corner
wdenka6c7ad22002-12-03 21:28:10 +0000463 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
464 linux_logo.h for logo.
465 Requires CONFIG_VIDEO_LOGO
wdenkc6097192002-11-03 00:24:07 +0000466 CONFIG_CONSOLE_EXTRA_INFO
467 addional board info beside
468 the logo
469
wdenk43d96162003-03-06 00:02:04 +0000470 When CONFIG_CFB_CONSOLE is defined, video console is
471 default i/o. Serial console can be forced with
472 environment 'console=serial'.
wdenkc6097192002-11-03 00:24:07 +0000473
wdenkd4ca31c2004-01-02 14:00:00 +0000474 When CONFIG_SILENT_CONSOLE is defined, all console
475 messages (by U-Boot and Linux!) can be silenced with
476 the "silent" environment variable. See
477 doc/README.silent for more information.
wdenka3ad8e22003-10-19 23:22:11 +0000478
wdenkc6097192002-11-03 00:24:07 +0000479- Console Baudrate:
480 CONFIG_BAUDRATE - in bps
481 Select one of the baudrates listed in
482 CFG_BAUDRATE_TABLE, see below.
wdenk3bbc8992003-12-07 22:27:15 +0000483 CFG_BRGCLK_PRESCALE, baudrate prescale
wdenkc6097192002-11-03 00:24:07 +0000484
485- Interrupt driven serial port input:
486 CONFIG_SERIAL_SOFTWARE_FIFO
487
488 PPC405GP only.
489 Use an interrupt handler for receiving data on the
490 serial port. It also enables using hardware handshake
491 (RTS/CTS) and UART's built-in FIFO. Set the number of
492 bytes the interrupt driven input buffer should have.
493
wdenk109c0e32004-03-23 21:43:07 +0000494 Leave undefined to disable this feature, including
495 disable the buffer and hardware handshake.
wdenkc6097192002-11-03 00:24:07 +0000496
stroese1d49b1f2003-05-23 11:39:05 +0000497- Console UART Number:
498 CONFIG_UART1_CONSOLE
499
500 IBM PPC4xx only.
501 If defined internal UART1 (and not UART0) is used
502 as default U-Boot console.
503
wdenkc6097192002-11-03 00:24:07 +0000504- Boot Delay: CONFIG_BOOTDELAY - in seconds
505 Delay before automatically booting the default image;
506 set to -1 to disable autoboot.
507
508 See doc/README.autoboot for these options that
509 work with CONFIG_BOOTDELAY. None are required.
510 CONFIG_BOOT_RETRY_TIME
511 CONFIG_BOOT_RETRY_MIN
512 CONFIG_AUTOBOOT_KEYED
513 CONFIG_AUTOBOOT_PROMPT
514 CONFIG_AUTOBOOT_DELAY_STR
515 CONFIG_AUTOBOOT_STOP_STR
516 CONFIG_AUTOBOOT_DELAY_STR2
517 CONFIG_AUTOBOOT_STOP_STR2
518 CONFIG_ZERO_BOOTDELAY_CHECK
519 CONFIG_RESET_TO_RETRY
520
521- Autoboot Command:
522 CONFIG_BOOTCOMMAND
523 Only needed when CONFIG_BOOTDELAY is enabled;
524 define a command string that is automatically executed
525 when no character is read on the console interface
526 within "Boot Delay" after reset.
527
528 CONFIG_BOOTARGS
wdenk43d96162003-03-06 00:02:04 +0000529 This can be used to pass arguments to the bootm
530 command. The value of CONFIG_BOOTARGS goes into the
531 environment value "bootargs".
wdenkc6097192002-11-03 00:24:07 +0000532
533 CONFIG_RAMBOOT and CONFIG_NFSBOOT
wdenk43d96162003-03-06 00:02:04 +0000534 The value of these goes into the environment as
535 "ramboot" and "nfsboot" respectively, and can be used
536 as a convenience, when switching between booting from
537 ram and nfs.
wdenkc6097192002-11-03 00:24:07 +0000538
539- Pre-Boot Commands:
540 CONFIG_PREBOOT
541
542 When this option is #defined, the existence of the
543 environment variable "preboot" will be checked
544 immediately before starting the CONFIG_BOOTDELAY
545 countdown and/or running the auto-boot command resp.
546 entering interactive mode.
547
548 This feature is especially useful when "preboot" is
549 automatically generated or modified. For an example
550 see the LWMON board specific code: here "preboot" is
551 modified when the user holds down a certain
552 combination of keys on the (special) keyboard when
553 booting the systems
554
555- Serial Download Echo Mode:
556 CONFIG_LOADS_ECHO
557 If defined to 1, all characters received during a
558 serial download (using the "loads" command) are
559 echoed back. This might be needed by some terminal
560 emulations (like "cu"), but may as well just take
561 time on others. This setting #define's the initial
562 value of the "loads_echo" environment variable.
563
564- Kgdb Serial Baudrate: (if CFG_CMD_KGDB is defined)
565 CONFIG_KGDB_BAUDRATE
566 Select one of the baudrates listed in
567 CFG_BAUDRATE_TABLE, see below.
568
569- Monitor Functions:
570 CONFIG_COMMANDS
571 Most monitor functions can be selected (or
572 de-selected) by adjusting the definition of
573 CONFIG_COMMANDS; to select individual functions,
574 #define CONFIG_COMMANDS by "OR"ing any of the
575 following values:
576
577 #define enables commands:
578 -------------------------
579 CFG_CMD_ASKENV * ask for env variable
wdenk78137c32003-09-15 18:00:00 +0000580 CFG_CMD_AUTOSCRIPT Autoscript Support
wdenkc6097192002-11-03 00:24:07 +0000581 CFG_CMD_BDI bdinfo
wdenk6705d812004-08-02 23:22:59 +0000582 CFG_CMD_BEDBUG * Include BedBug Debugger
wdenkba56f622004-02-06 23:19:44 +0000583 CFG_CMD_BMP * BMP support
wdenk6705d812004-08-02 23:22:59 +0000584 CFG_CMD_BSP * Board specific commands
wdenkc6097192002-11-03 00:24:07 +0000585 CFG_CMD_BOOTD bootd
wdenk6705d812004-08-02 23:22:59 +0000586 CFG_CMD_CACHE * icache, dcache
wdenkc6097192002-11-03 00:24:07 +0000587 CFG_CMD_CONSOLE coninfo
588 CFG_CMD_DATE * support for RTC, date/time...
wdenk6705d812004-08-02 23:22:59 +0000589 CFG_CMD_DHCP * DHCP support
wdenkba56f622004-02-06 23:19:44 +0000590 CFG_CMD_DIAG * Diagnostics
591 CFG_CMD_DOC * Disk-On-Chip Support
wdenk6705d812004-08-02 23:22:59 +0000592 CFG_CMD_DTT * Digital Therm and Thermostat
wdenkc6097192002-11-03 00:24:07 +0000593 CFG_CMD_ECHO * echo arguments
594 CFG_CMD_EEPROM * EEPROM read/write support
wdenk6705d812004-08-02 23:22:59 +0000595 CFG_CMD_ELF * bootelf, bootvx
wdenkc6097192002-11-03 00:24:07 +0000596 CFG_CMD_ENV saveenv
597 CFG_CMD_FDC * Floppy Disk Support
wdenk6705d812004-08-02 23:22:59 +0000598 CFG_CMD_FAT * FAT partition support
wdenk2262cfe2002-11-18 00:14:45 +0000599 CFG_CMD_FDOS * Dos diskette Support
wdenkc6097192002-11-03 00:24:07 +0000600 CFG_CMD_FLASH flinfo, erase, protect
601 CFG_CMD_FPGA FPGA device initialization support
wdenkba56f622004-02-06 23:19:44 +0000602 CFG_CMD_HWFLOW * RTS/CTS hw flow control
wdenkc6097192002-11-03 00:24:07 +0000603 CFG_CMD_I2C * I2C serial bus support
604 CFG_CMD_IDE * IDE harddisk support
605 CFG_CMD_IMI iminfo
wdenkba56f622004-02-06 23:19:44 +0000606 CFG_CMD_IMLS List all found images
wdenkc6097192002-11-03 00:24:07 +0000607 CFG_CMD_IMMAP * IMMR dump support
608 CFG_CMD_IRQ * irqinfo
wdenk6705d812004-08-02 23:22:59 +0000609 CFG_CMD_ITEST Integer/string test of 2 values
wdenkba56f622004-02-06 23:19:44 +0000610 CFG_CMD_JFFS2 * JFFS2 Support
wdenkc6097192002-11-03 00:24:07 +0000611 CFG_CMD_KGDB * kgdb
612 CFG_CMD_LOADB loadb
613 CFG_CMD_LOADS loads
614 CFG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
wdenk56523f12004-07-11 17:40:54 +0000615 loop, loopw, mtest
wdenkba56f622004-02-06 23:19:44 +0000616 CFG_CMD_MISC Misc functions like sleep etc
wdenk6705d812004-08-02 23:22:59 +0000617 CFG_CMD_MMC * MMC memory mapped support
618 CFG_CMD_MII * MII utility commands
wdenkba56f622004-02-06 23:19:44 +0000619 CFG_CMD_NAND * NAND support
wdenkc6097192002-11-03 00:24:07 +0000620 CFG_CMD_NET bootp, tftpboot, rarpboot
621 CFG_CMD_PCI * pciinfo
622 CFG_CMD_PCMCIA * PCMCIA support
wdenkba56f622004-02-06 23:19:44 +0000623 CFG_CMD_PING * send ICMP ECHO_REQUEST to network host
624 CFG_CMD_PORTIO * Port I/O
wdenkc6097192002-11-03 00:24:07 +0000625 CFG_CMD_REGINFO * Register dump
626 CFG_CMD_RUN run command in env variable
wdenk6705d812004-08-02 23:22:59 +0000627 CFG_CMD_SAVES * save S record dump
wdenkc6097192002-11-03 00:24:07 +0000628 CFG_CMD_SCSI * SCSI Support
wdenkba56f622004-02-06 23:19:44 +0000629 CFG_CMD_SDRAM * print SDRAM configuration information
wdenkb1bf6f22005-04-03 14:52:59 +0000630 (requires CFG_CMD_I2C)
wdenkc6097192002-11-03 00:24:07 +0000631 CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
632 CFG_CMD_SPI * SPI serial bus support
633 CFG_CMD_USB * USB support
wdenkba56f622004-02-06 23:19:44 +0000634 CFG_CMD_VFD * VFD support (TRAB)
wdenkc6097192002-11-03 00:24:07 +0000635 CFG_CMD_BSP * Board SPecific functions
wdenka3d991b2004-04-15 21:48:45 +0000636 CFG_CMD_CDP * Cisco Discover Protocol support
wdenkc6097192002-11-03 00:24:07 +0000637 -----------------------------------------------
638 CFG_CMD_ALL all
639
wdenk81050922004-07-11 20:04:51 +0000640 CONFIG_CMD_DFL Default configuration; at the moment
wdenkc6097192002-11-03 00:24:07 +0000641 this is includes all commands, except
642 the ones marked with "*" in the list
643 above.
644
645 If you don't define CONFIG_COMMANDS it defaults to
wdenk81050922004-07-11 20:04:51 +0000646 CONFIG_CMD_DFL in include/cmd_confdefs.h. A board can
wdenkc6097192002-11-03 00:24:07 +0000647 override the default settings in the respective
648 include file.
649
650 EXAMPLE: If you want all functions except of network
651 support you can write:
652
653 #define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET)
654
655
656 Note: Don't enable the "icache" and "dcache" commands
wdenk43d96162003-03-06 00:02:04 +0000657 (configuration option CFG_CMD_CACHE) unless you know
658 what you (and your U-Boot users) are doing. Data
659 cache cannot be enabled on systems like the 8xx or
660 8260 (where accesses to the IMMR region must be
661 uncached), and it cannot be disabled on all other
662 systems where we (mis-) use the data cache to hold an
663 initial stack and some data.
wdenkc6097192002-11-03 00:24:07 +0000664
665
666 XXX - this list needs to get updated!
667
668- Watchdog:
669 CONFIG_WATCHDOG
670 If this variable is defined, it enables watchdog
wdenk7152b1d2003-09-05 23:19:14 +0000671 support. There must be support in the platform specific
wdenkc6097192002-11-03 00:24:07 +0000672 code for a watchdog. For the 8xx and 8260 CPUs, the
673 SIU Watchdog feature is enabled in the SYPCR
674 register.
675
stroesec1551ea2003-04-04 15:53:41 +0000676- U-Boot Version:
677 CONFIG_VERSION_VARIABLE
678 If this variable is defined, an environment variable
679 named "ver" is created by U-Boot showing the U-Boot
680 version as printed by the "version" command.
681 This variable is readonly.
682
wdenkc6097192002-11-03 00:24:07 +0000683- Real-Time Clock:
684
685 When CFG_CMD_DATE is selected, the type of the RTC
686 has to be selected, too. Define exactly one of the
687 following options:
688
689 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
690 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
691 CONFIG_RTC_MC146818 - use MC146818 RTC
wdenk1cb8e982003-03-06 21:55:29 +0000692 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
wdenkc6097192002-11-03 00:24:07 +0000693 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
wdenk7f70e852003-05-20 14:25:27 +0000694 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
wdenk3bac3512003-03-12 10:41:04 +0000695 CONFIG_RTC_DS164x - use Dallas DS164x RTC
wdenk4c0d4c32004-06-09 17:34:58 +0000696 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
wdenkc6097192002-11-03 00:24:07 +0000697
wdenkb37c7e52003-06-30 16:24:52 +0000698 Note that if the RTC uses I2C, then the I2C interface
699 must also be configured. See I2C Support, below.
700
wdenkc6097192002-11-03 00:24:07 +0000701- Timestamp Support:
702
wdenk43d96162003-03-06 00:02:04 +0000703 When CONFIG_TIMESTAMP is selected, the timestamp
704 (date and time) of an image is printed by image
705 commands like bootm or iminfo. This option is
706 automatically enabled when you select CFG_CMD_DATE .
wdenkc6097192002-11-03 00:24:07 +0000707
708- Partition Support:
709 CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
710 and/or CONFIG_ISO_PARTITION
711
712 If IDE or SCSI support is enabled (CFG_CMD_IDE or
713 CFG_CMD_SCSI) you must configure support for at least
714 one partition type as well.
715
716- IDE Reset method:
wdenk4d13cba2004-03-14 14:09:05 +0000717 CONFIG_IDE_RESET_ROUTINE - this is defined in several
718 board configurations files but used nowhere!
wdenkc6097192002-11-03 00:24:07 +0000719
wdenk4d13cba2004-03-14 14:09:05 +0000720 CONFIG_IDE_RESET - is this is defined, IDE Reset will
721 be performed by calling the function
722 ide_set_reset(int reset)
723 which has to be defined in a board specific file
wdenkc6097192002-11-03 00:24:07 +0000724
725- ATAPI Support:
726 CONFIG_ATAPI
727
728 Set this to enable ATAPI support.
729
wdenkc40b2952004-03-13 23:29:43 +0000730- LBA48 Support
731 CONFIG_LBA48
732
733 Set this to enable support for disks larger than 137GB
734 Also look at CFG_64BIT_LBA ,CFG_64BIT_VSPRINTF and CFG_64BIT_STRTOUL
735 Whithout these , LBA48 support uses 32bit variables and will 'only'
736 support disks up to 2.1TB.
737
738 CFG_64BIT_LBA:
739 When enabled, makes the IDE subsystem use 64bit sector addresses.
740 Default is 32bit.
741
wdenkc6097192002-11-03 00:24:07 +0000742- SCSI Support:
743 At the moment only there is only support for the
744 SYM53C8XX SCSI controller; define
745 CONFIG_SCSI_SYM53C8XX to enable it.
746
747 CFG_SCSI_MAX_LUN [8], CFG_SCSI_MAX_SCSI_ID [7] and
748 CFG_SCSI_MAX_DEVICE [CFG_SCSI_MAX_SCSI_ID *
749 CFG_SCSI_MAX_LUN] can be adjusted to define the
750 maximum numbers of LUNs, SCSI ID's and target
751 devices.
752 CFG_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
753
754- NETWORK Support (PCI):
wdenk682011f2003-06-03 23:54:09 +0000755 CONFIG_E1000
756 Support for Intel 8254x gigabit chips.
stroese53cf9432003-06-05 15:39:44 +0000757
wdenkc6097192002-11-03 00:24:07 +0000758 CONFIG_EEPRO100
759 Support for Intel 82557/82559/82559ER chips.
760 Optional CONFIG_EEPRO100_SROM_WRITE enables eeprom
761 write routine for first time initialisation.
762
763 CONFIG_TULIP
764 Support for Digital 2114x chips.
765 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
766 modem chip initialisation (KS8761/QS6611).
767
768 CONFIG_NATSEMI
769 Support for National dp83815 chips.
770
771 CONFIG_NS8382X
772 Support for National dp8382[01] gigabit chips.
773
wdenk45219c42003-05-12 21:50:16 +0000774- NETWORK Support (other):
775
776 CONFIG_DRIVER_LAN91C96
777 Support for SMSC's LAN91C96 chips.
778
779 CONFIG_LAN91C96_BASE
780 Define this to hold the physical address
781 of the LAN91C96's I/O space
782
783 CONFIG_LAN91C96_USE_32_BIT
784 Define this to enable 32 bit addressing
785
wdenkf39748a2004-06-09 13:37:52 +0000786 CONFIG_DRIVER_SMC91111
787 Support for SMSC's LAN91C111 chip
788
789 CONFIG_SMC91111_BASE
790 Define this to hold the physical address
791 of the device (I/O space)
792
793 CONFIG_SMC_USE_32_BIT
794 Define this if data bus is 32 bits
795
796 CONFIG_SMC_USE_IOFUNCS
797 Define this to use i/o functions instead of macros
798 (some hardware wont work with macros)
799
wdenkc6097192002-11-03 00:24:07 +0000800- USB Support:
801 At the moment only the UHCI host controller is
wdenk4d13cba2004-03-14 14:09:05 +0000802 supported (PIP405, MIP405, MPC5200); define
wdenkc6097192002-11-03 00:24:07 +0000803 CONFIG_USB_UHCI to enable it.
804 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
wdenk30d56fa2004-10-09 22:44:59 +0000805 and define CONFIG_USB_STORAGE to enable the USB
wdenkc6097192002-11-03 00:24:07 +0000806 storage devices.
807 Note:
808 Supported are USB Keyboards and USB Floppy drives
809 (TEAC FD-05PUB).
wdenk4d13cba2004-03-14 14:09:05 +0000810 MPC5200 USB requires additional defines:
811 CONFIG_USB_CLOCK
812 for 528 MHz Clock: 0x0001bbbb
813 CONFIG_USB_CONFIG
814 for differential drivers: 0x00001000
815 for single ended drivers: 0x00005000
816
wdenkc6097192002-11-03 00:24:07 +0000817
wdenk71f95112003-06-15 22:40:42 +0000818- MMC Support:
wdenk8bde7f72003-06-27 21:31:46 +0000819 The MMC controller on the Intel PXA is supported. To
820 enable this define CONFIG_MMC. The MMC can be
821 accessed from the boot prompt by mapping the device
wdenk71f95112003-06-15 22:40:42 +0000822 to physical memory similar to flash. Command line is
823 enabled with CFG_CMD_MMC. The MMC driver also works with
wdenk8bde7f72003-06-27 21:31:46 +0000824 the FAT fs. This is enabled with CFG_CMD_FAT.
wdenk71f95112003-06-15 22:40:42 +0000825
wdenk6705d812004-08-02 23:22:59 +0000826- Journaling Flash filesystem support:
827 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
828 CONFIG_JFFS2_NAND_DEV
829 Define these for a default partition on a NAND device
830
831 CFG_JFFS2_FIRST_SECTOR,
832 CFG_JFFS2_FIRST_BANK, CFG_JFFS2_NUM_BANKS
833 Define these for a default partition on a NOR device
834
835 CFG_JFFS_CUSTOM_PART
836 Define this to create an own partition. You have to provide a
837 function struct part_info* jffs2_part_info(int part_num)
838
839 If you define only one JFFS2 partition you may also want to
wdenkefe2a4d2004-12-16 21:44:03 +0000840 #define CFG_JFFS_SINGLE_PART 1
wdenk6705d812004-08-02 23:22:59 +0000841 to disable the command chpart. This is the default when you
842 have not defined a custom partition
843
wdenkc6097192002-11-03 00:24:07 +0000844- Keyboard Support:
845 CONFIG_ISA_KEYBOARD
846
847 Define this to enable standard (PC-Style) keyboard
848 support
849
850 CONFIG_I8042_KBD
851 Standard PC keyboard driver with US (is default) and
852 GERMAN key layout (switch via environment 'keymap=de') support.
853 Export function i8042_kbd_init, i8042_tstc and i8042_getc
854 for cfb_console. Supports cursor blinking.
855
856- Video support:
857 CONFIG_VIDEO
858
859 Define this to enable video support (for output to
860 video).
861
862 CONFIG_VIDEO_CT69000
863
864 Enable Chips & Technologies 69000 Video chip
865
866 CONFIG_VIDEO_SMI_LYNXEM
wdenkb79a11c2004-03-25 15:14:43 +0000867 Enable Silicon Motion SMI 712/710/810 Video chip. The
wdenkeeb1b772004-03-23 22:53:55 +0000868 video output is selected via environment 'videoout'
869 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
870 assumed.
wdenkc6097192002-11-03 00:24:07 +0000871
wdenkb79a11c2004-03-25 15:14:43 +0000872 For the CT69000 and SMI_LYNXEM drivers, videomode is
873 selected via environment 'videomode'. Two diferent ways
wdenkeeb1b772004-03-23 22:53:55 +0000874 are possible:
875 - "videomode=num" 'num' is a standard LiLo mode numbers.
wdenk6e592382004-04-18 17:39:38 +0000876 Following standard modes are supported (* is default):
wdenkeeb1b772004-03-23 22:53:55 +0000877
878 Colors 640x480 800x600 1024x768 1152x864 1280x1024
879 -------------+---------------------------------------------
880 8 bits | 0x301* 0x303 0x305 0x161 0x307
881 15 bits | 0x310 0x313 0x316 0x162 0x319
882 16 bits | 0x311 0x314 0x317 0x163 0x31A
883 24 bits | 0x312 0x315 0x318 ? 0x31B
884 -------------+---------------------------------------------
wdenkc6097192002-11-03 00:24:07 +0000885 (i.e. setenv videomode 317; saveenv; reset;)
886
wdenkb79a11c2004-03-25 15:14:43 +0000887 - "videomode=bootargs" all the video parameters are parsed
wdenkeeb1b772004-03-23 22:53:55 +0000888 from the bootargs. (See drivers/videomodes.c)
889
890
stroesec1551ea2003-04-04 15:53:41 +0000891 CONFIG_VIDEO_SED13806
wdenk43d96162003-03-06 00:02:04 +0000892 Enable Epson SED13806 driver. This driver supports 8bpp
wdenka6c7ad22002-12-03 21:28:10 +0000893 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
894 or CONFIG_VIDEO_SED13806_16BPP
895
wdenk682011f2003-06-03 23:54:09 +0000896- Keyboard Support:
wdenk8bde7f72003-06-27 21:31:46 +0000897 CONFIG_KEYBOARD
wdenk682011f2003-06-03 23:54:09 +0000898
wdenk8bde7f72003-06-27 21:31:46 +0000899 Define this to enable a custom keyboard support.
900 This simply calls drv_keyboard_init() which must be
901 defined in your board-specific files.
902 The only board using this so far is RBC823.
wdenka6c7ad22002-12-03 21:28:10 +0000903
wdenkc6097192002-11-03 00:24:07 +0000904- LCD Support: CONFIG_LCD
905
906 Define this to enable LCD support (for output to LCD
907 display); also select one of the supported displays
908 by defining one of these:
909
wdenkfd3103b2003-11-25 16:55:19 +0000910 CONFIG_NEC_NL6448AC33:
wdenkc6097192002-11-03 00:24:07 +0000911
wdenkfd3103b2003-11-25 16:55:19 +0000912 NEC NL6448AC33-18. Active, color, single scan.
wdenkc6097192002-11-03 00:24:07 +0000913
wdenkfd3103b2003-11-25 16:55:19 +0000914 CONFIG_NEC_NL6448BC20
wdenkc6097192002-11-03 00:24:07 +0000915
wdenkfd3103b2003-11-25 16:55:19 +0000916 NEC NL6448BC20-08. 6.5", 640x480.
917 Active, color, single scan.
918
919 CONFIG_NEC_NL6448BC33_54
920
921 NEC NL6448BC33-54. 10.4", 640x480.
wdenkc6097192002-11-03 00:24:07 +0000922 Active, color, single scan.
923
924 CONFIG_SHARP_16x9
925
926 Sharp 320x240. Active, color, single scan.
927 It isn't 16x9, and I am not sure what it is.
928
929 CONFIG_SHARP_LQ64D341
930
931 Sharp LQ64D341 display, 640x480.
932 Active, color, single scan.
933
934 CONFIG_HLD1045
935
936 HLD1045 display, 640x480.
937 Active, color, single scan.
938
939 CONFIG_OPTREX_BW
940
941 Optrex CBL50840-2 NF-FW 99 22 M5
942 or
943 Hitachi LMG6912RPFC-00T
944 or
945 Hitachi SP14Q002
946
947 320x240. Black & white.
948
949 Normally display is black on white background; define
950 CFG_WHITE_ON_BLACK to get it inverted.
951
wdenk7152b1d2003-09-05 23:19:14 +0000952- Splash Screen Support: CONFIG_SPLASH_SCREEN
wdenkd791b1d2003-04-20 14:04:18 +0000953
wdenk8bde7f72003-06-27 21:31:46 +0000954 If this option is set, the environment is checked for
955 a variable "splashimage". If found, the usual display
956 of logo, copyright and system information on the LCD
wdenke94d2cd2004-06-30 22:59:18 +0000957 is suppressed and the BMP image at the address
wdenk8bde7f72003-06-27 21:31:46 +0000958 specified in "splashimage" is loaded instead. The
959 console is redirected to the "nulldev", too. This
960 allows for a "silent" boot where a splash screen is
961 loaded very quickly after power-on.
wdenkd791b1d2003-04-20 14:04:18 +0000962
wdenkc29fdfc2003-08-29 20:57:53 +0000963- Compression support:
964 CONFIG_BZIP2
965
966 If this option is set, support for bzip2 compressed
967 images is included. If not, only uncompressed and gzip
968 compressed images are supported.
969
wdenk42d1f032003-10-15 23:53:47 +0000970 NOTE: the bzip2 algorithm requires a lot of RAM, so
971 the malloc area (as defined by CFG_MALLOC_LEN) should
972 be at least 4MB.
wdenkd791b1d2003-04-20 14:04:18 +0000973
wdenk17ea1172004-06-06 21:51:03 +0000974- MII/PHY support:
975 CONFIG_PHY_ADDR
976
977 The address of PHY on MII bus.
978
979 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
980
981 The clock frequency of the MII bus
982
983 CONFIG_PHY_GIGE
984
985 If this option is set, support for speed/duplex
986 detection of Gigabit PHY is included.
987
988 CONFIG_PHY_RESET_DELAY
989
990 Some PHY like Intel LXT971A need extra delay after
991 reset before any MII register access is possible.
992 For such PHY, set this option to the usec delay
993 required. (minimum 300usec for LXT971A)
994
995 CONFIG_PHY_CMD_DELAY (ppc4xx)
996
997 Some PHY like Intel LXT971A need extra delay after
998 command issued before MII status register can be read
999
wdenkc6097192002-11-03 00:24:07 +00001000- Ethernet address:
1001 CONFIG_ETHADDR
1002 CONFIG_ETH2ADDR
1003 CONFIG_ETH3ADDR
1004
1005 Define a default value for ethernet address to use
1006 for the respective ethernet interface, in case this
1007 is not determined automatically.
1008
1009- IP address:
1010 CONFIG_IPADDR
1011
1012 Define a default value for the IP address to use for
1013 the default ethernet interface, in case this is not
1014 determined through e.g. bootp.
1015
1016- Server IP address:
1017 CONFIG_SERVERIP
1018
1019 Defines a default value for theIP address of a TFTP
1020 server to contact when using the "tftboot" command.
1021
1022- BOOTP Recovery Mode:
1023 CONFIG_BOOTP_RANDOM_DELAY
1024
1025 If you have many targets in a network that try to
1026 boot using BOOTP, you may want to avoid that all
1027 systems send out BOOTP requests at precisely the same
1028 moment (which would happen for instance at recovery
1029 from a power failure, when all systems will try to
1030 boot, thus flooding the BOOTP server. Defining
1031 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1032 inserted before sending out BOOTP requests. The
1033 following delays are insterted then:
1034
1035 1st BOOTP request: delay 0 ... 1 sec
1036 2nd BOOTP request: delay 0 ... 2 sec
1037 3rd BOOTP request: delay 0 ... 4 sec
1038 4th and following
1039 BOOTP requests: delay 0 ... 8 sec
1040
stroesefe389a82003-08-28 14:17:32 +00001041- DHCP Advanced Options:
1042 CONFIG_BOOTP_MASK
1043
1044 You can fine tune the DHCP functionality by adding
1045 these flags to the CONFIG_BOOTP_MASK define:
1046
1047 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1048 serverip from a DHCP server, it is possible that more
1049 than one DNS serverip is offered to the client.
1050 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1051 serverip will be stored in the additional environment
1052 variable "dnsip2". The first DNS serverip is always
1053 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1054 is added to the CONFIG_BOOTP_MASK.
1055
1056 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1057 to do a dynamic update of a DNS server. To do this, they
1058 need the hostname of the DHCP requester.
1059 If CONFIG_BOOP_SEND_HOSTNAME is added to the
1060 CONFIG_BOOTP_MASK, the content of the "hostname"
1061 environment variable is passed as option 12 to
1062 the DHCP server.
1063
wdenka3d991b2004-04-15 21:48:45 +00001064 - CDP Options:
wdenk6e592382004-04-18 17:39:38 +00001065 CONFIG_CDP_DEVICE_ID
wdenka3d991b2004-04-15 21:48:45 +00001066
1067 The device id used in CDP trigger frames.
1068
1069 CONFIG_CDP_DEVICE_ID_PREFIX
1070
1071 A two character string which is prefixed to the MAC address
1072 of the device.
1073
1074 CONFIG_CDP_PORT_ID
1075
1076 A printf format string which contains the ascii name of
1077 the port. Normally is set to "eth%d" which sets
1078 eth0 for the first ethernet, eth1 for the second etc.
1079
1080 CONFIG_CDP_CAPABILITIES
1081
1082 A 32bit integer which indicates the device capabilities;
1083 0x00000010 for a normal host which does not forwards.
1084
1085 CONFIG_CDP_VERSION
1086
1087 An ascii string containing the version of the software.
1088
1089 CONFIG_CDP_PLATFORM
1090
1091 An ascii string containing the name of the platform.
1092
1093 CONFIG_CDP_TRIGGER
1094
1095 A 32bit integer sent on the trigger.
1096
1097 CONFIG_CDP_POWER_CONSUMPTION
1098
1099 A 16bit integer containing the power consumption of the
1100 device in .1 of milliwatts.
1101
1102 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1103
1104 A byte containing the id of the VLAN.
1105
wdenkc6097192002-11-03 00:24:07 +00001106- Status LED: CONFIG_STATUS_LED
1107
1108 Several configurations allow to display the current
1109 status using a LED. For instance, the LED will blink
1110 fast while running U-Boot code, stop blinking as
1111 soon as a reply to a BOOTP request was received, and
1112 start blinking slow once the Linux kernel is running
1113 (supported by a status LED driver in the Linux
1114 kernel). Defining CONFIG_STATUS_LED enables this
1115 feature in U-Boot.
1116
1117- CAN Support: CONFIG_CAN_DRIVER
1118
1119 Defining CONFIG_CAN_DRIVER enables CAN driver support
1120 on those systems that support this (optional)
1121 feature, like the TQM8xxL modules.
1122
1123- I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1124
wdenkb37c7e52003-06-30 16:24:52 +00001125 These enable I2C serial bus commands. Defining either of
wdenk945af8d2003-07-16 21:53:01 +00001126 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
1127 include the appropriate I2C driver for the selected cpu.
wdenkc6097192002-11-03 00:24:07 +00001128
wdenk945af8d2003-07-16 21:53:01 +00001129 This will allow you to use i2c commands at the u-boot
1130 command line (as long as you set CFG_CMD_I2C in
wdenkb37c7e52003-06-30 16:24:52 +00001131 CONFIG_COMMANDS) and communicate with i2c based realtime
1132 clock chips. See common/cmd_i2c.c for a description of the
wdenk43d96162003-03-06 00:02:04 +00001133 command line interface.
wdenkc6097192002-11-03 00:24:07 +00001134
wdenkba56f622004-02-06 23:19:44 +00001135 CONFIG_HARD_I2C selects the CPM hardware driver for I2C.
wdenkc6097192002-11-03 00:24:07 +00001136
wdenk945af8d2003-07-16 21:53:01 +00001137 CONFIG_SOFT_I2C configures u-boot to use a software (aka
wdenkb37c7e52003-06-30 16:24:52 +00001138 bit-banging) driver instead of CPM or similar hardware
1139 support for I2C.
wdenkc6097192002-11-03 00:24:07 +00001140
wdenk945af8d2003-07-16 21:53:01 +00001141 There are several other quantities that must also be
wdenkb37c7e52003-06-30 16:24:52 +00001142 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
wdenkc6097192002-11-03 00:24:07 +00001143
wdenkb37c7e52003-06-30 16:24:52 +00001144 In both cases you will need to define CFG_I2C_SPEED
wdenk945af8d2003-07-16 21:53:01 +00001145 to be the frequency (in Hz) at which you wish your i2c bus
1146 to run and CFG_I2C_SLAVE to be the address of this node (ie
1147 the cpu's i2c node address).
1148
wdenkb37c7e52003-06-30 16:24:52 +00001149 Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c)
1150 sets the cpu up as a master node and so its address should
1151 therefore be cleared to 0 (See, eg, MPC823e User's Manual
wdenk945af8d2003-07-16 21:53:01 +00001152 p.16-473). So, set CFG_I2C_SLAVE to 0.
wdenkc6097192002-11-03 00:24:07 +00001153
wdenk945af8d2003-07-16 21:53:01 +00001154 That's all that's required for CONFIG_HARD_I2C.
wdenkb37c7e52003-06-30 16:24:52 +00001155
1156 If you use the software i2c interface (CONFIG_SOFT_I2C)
1157 then the following macros need to be defined (examples are
1158 from include/configs/lwmon.h):
wdenkc6097192002-11-03 00:24:07 +00001159
1160 I2C_INIT
1161
wdenkb37c7e52003-06-30 16:24:52 +00001162 (Optional). Any commands necessary to enable the I2C
wdenk43d96162003-03-06 00:02:04 +00001163 controller or configure ports.
wdenkc6097192002-11-03 00:24:07 +00001164
wdenkba56f622004-02-06 23:19:44 +00001165 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
wdenkb37c7e52003-06-30 16:24:52 +00001166
wdenkc6097192002-11-03 00:24:07 +00001167 I2C_PORT
1168
wdenk43d96162003-03-06 00:02:04 +00001169 (Only for MPC8260 CPU). The I/O port to use (the code
1170 assumes both bits are on the same port). Valid values
1171 are 0..3 for ports A..D.
wdenkc6097192002-11-03 00:24:07 +00001172
1173 I2C_ACTIVE
1174
1175 The code necessary to make the I2C data line active
1176 (driven). If the data line is open collector, this
1177 define can be null.
1178
wdenkb37c7e52003-06-30 16:24:52 +00001179 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1180
wdenkc6097192002-11-03 00:24:07 +00001181 I2C_TRISTATE
1182
1183 The code necessary to make the I2C data line tri-stated
1184 (inactive). If the data line is open collector, this
1185 define can be null.
1186
wdenkb37c7e52003-06-30 16:24:52 +00001187 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1188
wdenkc6097192002-11-03 00:24:07 +00001189 I2C_READ
1190
1191 Code that returns TRUE if the I2C data line is high,
1192 FALSE if it is low.
1193
wdenkb37c7e52003-06-30 16:24:52 +00001194 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1195
wdenkc6097192002-11-03 00:24:07 +00001196 I2C_SDA(bit)
1197
1198 If <bit> is TRUE, sets the I2C data line high. If it
1199 is FALSE, it clears it (low).
1200
wdenkb37c7e52003-06-30 16:24:52 +00001201 eg: #define I2C_SDA(bit) \
wdenk2535d602003-07-17 23:16:40 +00001202 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
wdenkba56f622004-02-06 23:19:44 +00001203 else immr->im_cpm.cp_pbdat &= ~PB_SDA
wdenkb37c7e52003-06-30 16:24:52 +00001204
wdenkc6097192002-11-03 00:24:07 +00001205 I2C_SCL(bit)
1206
1207 If <bit> is TRUE, sets the I2C clock line high. If it
1208 is FALSE, it clears it (low).
1209
wdenkb37c7e52003-06-30 16:24:52 +00001210 eg: #define I2C_SCL(bit) \
wdenk2535d602003-07-17 23:16:40 +00001211 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
wdenkba56f622004-02-06 23:19:44 +00001212 else immr->im_cpm.cp_pbdat &= ~PB_SCL
wdenkb37c7e52003-06-30 16:24:52 +00001213
wdenkc6097192002-11-03 00:24:07 +00001214 I2C_DELAY
1215
1216 This delay is invoked four times per clock cycle so this
1217 controls the rate of data transfer. The data rate thus
wdenkb37c7e52003-06-30 16:24:52 +00001218 is 1 / (I2C_DELAY * 4). Often defined to be something
wdenk945af8d2003-07-16 21:53:01 +00001219 like:
1220
wdenkb37c7e52003-06-30 16:24:52 +00001221 #define I2C_DELAY udelay(2)
wdenkc6097192002-11-03 00:24:07 +00001222
wdenk47cd00f2003-03-06 13:39:27 +00001223 CFG_I2C_INIT_BOARD
1224
wdenk8bde7f72003-06-27 21:31:46 +00001225 When a board is reset during an i2c bus transfer
1226 chips might think that the current transfer is still
1227 in progress. On some boards it is possible to access
1228 the i2c SCLK line directly, either by using the
1229 processor pin as a GPIO or by having a second pin
1230 connected to the bus. If this option is defined a
1231 custom i2c_init_board() routine in boards/xxx/board.c
1232 is run early in the boot sequence.
wdenk47cd00f2003-03-06 13:39:27 +00001233
wdenk17ea1172004-06-06 21:51:03 +00001234 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
1235
1236 This option enables configuration of bi_iic_fast[] flags
1237 in u-boot bd_info structure based on u-boot environment
1238 variable "i2cfast". (see also i2cfast)
1239
wdenkc6097192002-11-03 00:24:07 +00001240- SPI Support: CONFIG_SPI
1241
1242 Enables SPI driver (so far only tested with
1243 SPI EEPROM, also an instance works with Crystal A/D and
1244 D/As on the SACSng board)
1245
1246 CONFIG_SPI_X
1247
1248 Enables extended (16-bit) SPI EEPROM addressing.
1249 (symmetrical to CONFIG_I2C_X)
1250
1251 CONFIG_SOFT_SPI
1252
wdenk43d96162003-03-06 00:02:04 +00001253 Enables a software (bit-bang) SPI driver rather than
1254 using hardware support. This is a general purpose
1255 driver that only requires three general I/O port pins
1256 (two outputs, one input) to function. If this is
1257 defined, the board configuration must define several
1258 SPI configuration items (port pins to use, etc). For
1259 an example, see include/configs/sacsng.h.
wdenkc6097192002-11-03 00:24:07 +00001260
1261- FPGA Support: CONFIG_FPGA_COUNT
1262
wdenk43d96162003-03-06 00:02:04 +00001263 Specify the number of FPGA devices to support.
wdenkc6097192002-11-03 00:24:07 +00001264
wdenk43d96162003-03-06 00:02:04 +00001265 CONFIG_FPGA
wdenkc6097192002-11-03 00:24:07 +00001266
wdenk8bde7f72003-06-27 21:31:46 +00001267 Used to specify the types of FPGA devices. For example,
1268 #define CONFIG_FPGA CFG_XILINX_VIRTEX2
wdenkc6097192002-11-03 00:24:07 +00001269
wdenk8bde7f72003-06-27 21:31:46 +00001270 CFG_FPGA_PROG_FEEDBACK
wdenkc6097192002-11-03 00:24:07 +00001271
wdenk8bde7f72003-06-27 21:31:46 +00001272 Enable printing of hash marks during FPGA configuration.
wdenkc6097192002-11-03 00:24:07 +00001273
1274 CFG_FPGA_CHECK_BUSY
1275
wdenk43d96162003-03-06 00:02:04 +00001276 Enable checks on FPGA configuration interface busy
1277 status by the configuration function. This option
1278 will require a board or device specific function to
1279 be written.
wdenkc6097192002-11-03 00:24:07 +00001280
1281 CONFIG_FPGA_DELAY
1282
1283 If defined, a function that provides delays in the FPGA
1284 configuration driver.
1285
1286 CFG_FPGA_CHECK_CTRLC
1287 Allow Control-C to interrupt FPGA configuration
1288
1289 CFG_FPGA_CHECK_ERROR
1290
wdenk43d96162003-03-06 00:02:04 +00001291 Check for configuration errors during FPGA bitfile
1292 loading. For example, abort during Virtex II
1293 configuration if the INIT_B line goes low (which
1294 indicated a CRC error).
wdenkc6097192002-11-03 00:24:07 +00001295
1296 CFG_FPGA_WAIT_INIT
1297
wdenk43d96162003-03-06 00:02:04 +00001298 Maximum time to wait for the INIT_B line to deassert
1299 after PROB_B has been deasserted during a Virtex II
1300 FPGA configuration sequence. The default time is 500
1301 mS.
wdenkc6097192002-11-03 00:24:07 +00001302
1303 CFG_FPGA_WAIT_BUSY
1304
wdenk43d96162003-03-06 00:02:04 +00001305 Maximum time to wait for BUSY to deassert during
1306 Virtex II FPGA configuration. The default is 5 mS.
wdenkc6097192002-11-03 00:24:07 +00001307
1308 CFG_FPGA_WAIT_CONFIG
1309
wdenk43d96162003-03-06 00:02:04 +00001310 Time to wait after FPGA configuration. The default is
1311 200 mS.
wdenkc6097192002-11-03 00:24:07 +00001312
1313- Configuration Management:
1314 CONFIG_IDENT_STRING
1315
wdenk43d96162003-03-06 00:02:04 +00001316 If defined, this string will be added to the U-Boot
1317 version information (U_BOOT_VERSION)
wdenkc6097192002-11-03 00:24:07 +00001318
1319- Vendor Parameter Protection:
1320
wdenk43d96162003-03-06 00:02:04 +00001321 U-Boot considers the values of the environment
1322 variables "serial#" (Board Serial Number) and
wdenk7152b1d2003-09-05 23:19:14 +00001323 "ethaddr" (Ethernet Address) to be parameters that
wdenk43d96162003-03-06 00:02:04 +00001324 are set once by the board vendor / manufacturer, and
1325 protects these variables from casual modification by
1326 the user. Once set, these variables are read-only,
1327 and write or delete attempts are rejected. You can
1328 change this behviour:
wdenkc6097192002-11-03 00:24:07 +00001329
1330 If CONFIG_ENV_OVERWRITE is #defined in your config
1331 file, the write protection for vendor parameters is
wdenk47cd00f2003-03-06 13:39:27 +00001332 completely disabled. Anybody can change or delete
wdenkc6097192002-11-03 00:24:07 +00001333 these parameters.
1334
1335 Alternatively, if you #define _both_ CONFIG_ETHADDR
1336 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
1337 ethernet address is installed in the environment,
1338 which can be changed exactly ONCE by the user. [The
1339 serial# is unaffected by this, i. e. it remains
1340 read-only.]
1341
1342- Protected RAM:
1343 CONFIG_PRAM
1344
1345 Define this variable to enable the reservation of
1346 "protected RAM", i. e. RAM which is not overwritten
1347 by U-Boot. Define CONFIG_PRAM to hold the number of
1348 kB you want to reserve for pRAM. You can overwrite
1349 this default value by defining an environment
1350 variable "pram" to the number of kB you want to
1351 reserve. Note that the board info structure will
1352 still show the full amount of RAM. If pRAM is
1353 reserved, a new environment variable "mem" will
1354 automatically be defined to hold the amount of
1355 remaining RAM in a form that can be passed as boot
1356 argument to Linux, for instance like that:
1357
1358 setenv bootargs ... mem=\$(mem)
1359 saveenv
1360
1361 This way you can tell Linux not to use this memory,
1362 either, which results in a memory region that will
1363 not be affected by reboots.
1364
1365 *WARNING* If your board configuration uses automatic
1366 detection of the RAM size, you must make sure that
1367 this memory test is non-destructive. So far, the
1368 following board configurations are known to be
1369 "pRAM-clean":
1370
1371 ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
1372 HERMES, IP860, RPXlite, LWMON, LANTEC,
1373 PCU_E, FLAGADM, TQM8260
1374
1375- Error Recovery:
1376 CONFIG_PANIC_HANG
1377
1378 Define this variable to stop the system in case of a
1379 fatal error, so that you have to reset it manually.
1380 This is probably NOT a good idea for an embedded
1381 system where you want to system to reboot
1382 automatically as fast as possible, but it may be
1383 useful during development since you can try to debug
1384 the conditions that lead to the situation.
1385
1386 CONFIG_NET_RETRY_COUNT
1387
wdenk43d96162003-03-06 00:02:04 +00001388 This variable defines the number of retries for
1389 network operations like ARP, RARP, TFTP, or BOOTP
1390 before giving up the operation. If not defined, a
1391 default value of 5 is used.
wdenkc6097192002-11-03 00:24:07 +00001392
1393- Command Interpreter:
wdenk04a85b32004-04-15 18:22:41 +00001394 CFG_AUTO_COMPLETE
1395
1396 Enable auto completion of commands using TAB.
1397
wdenkc6097192002-11-03 00:24:07 +00001398 CFG_HUSH_PARSER
1399
1400 Define this variable to enable the "hush" shell (from
1401 Busybox) as command line interpreter, thus enabling
1402 powerful command line syntax like
1403 if...then...else...fi conditionals or `&&' and '||'
1404 constructs ("shell scripts").
1405
1406 If undefined, you get the old, much simpler behaviour
1407 with a somewhat smaller memory footprint.
1408
1409
1410 CFG_PROMPT_HUSH_PS2
1411
1412 This defines the secondary prompt string, which is
1413 printed when the command interpreter needs more input
1414 to complete a command. Usually "> ".
1415
1416 Note:
1417
wdenk8bde7f72003-06-27 21:31:46 +00001418 In the current implementation, the local variables
1419 space and global environment variables space are
1420 separated. Local variables are those you define by
1421 simply typing `name=value'. To access a local
1422 variable later on, you have write `$name' or
1423 `${name}'; to execute the contents of a variable
1424 directly type `$name' at the command prompt.
wdenkc6097192002-11-03 00:24:07 +00001425
wdenk43d96162003-03-06 00:02:04 +00001426 Global environment variables are those you use
1427 setenv/printenv to work with. To run a command stored
1428 in such a variable, you need to use the run command,
1429 and you must not use the '$' sign to access them.
wdenkc6097192002-11-03 00:24:07 +00001430
1431 To store commands and special characters in a
1432 variable, please use double quotation marks
1433 surrounding the whole text of the variable, instead
1434 of the backslashes before semicolons and special
1435 symbols.
1436
wdenka8c7c702003-12-06 19:49:23 +00001437- Default Environment:
wdenkc6097192002-11-03 00:24:07 +00001438 CONFIG_EXTRA_ENV_SETTINGS
1439
wdenk43d96162003-03-06 00:02:04 +00001440 Define this to contain any number of null terminated
1441 strings (variable = value pairs) that will be part of
wdenk7152b1d2003-09-05 23:19:14 +00001442 the default environment compiled into the boot image.
wdenk2262cfe2002-11-18 00:14:45 +00001443
wdenk43d96162003-03-06 00:02:04 +00001444 For example, place something like this in your
1445 board's config file:
wdenkc6097192002-11-03 00:24:07 +00001446
1447 #define CONFIG_EXTRA_ENV_SETTINGS \
1448 "myvar1=value1\0" \
1449 "myvar2=value2\0"
1450
wdenk43d96162003-03-06 00:02:04 +00001451 Warning: This method is based on knowledge about the
1452 internal format how the environment is stored by the
1453 U-Boot code. This is NOT an official, exported
1454 interface! Although it is unlikely that this format
wdenk7152b1d2003-09-05 23:19:14 +00001455 will change soon, there is no guarantee either.
wdenkc6097192002-11-03 00:24:07 +00001456 You better know what you are doing here.
1457
wdenk43d96162003-03-06 00:02:04 +00001458 Note: overly (ab)use of the default environment is
1459 discouraged. Make sure to check other ways to preset
1460 the environment like the autoscript function or the
1461 boot command first.
wdenkc6097192002-11-03 00:24:07 +00001462
wdenka8c7c702003-12-06 19:49:23 +00001463- DataFlash Support:
wdenk2abbe072003-06-16 23:50:08 +00001464 CONFIG_HAS_DATAFLASH
1465
wdenk8bde7f72003-06-27 21:31:46 +00001466 Defining this option enables DataFlash features and
1467 allows to read/write in Dataflash via the standard
1468 commands cp, md...
wdenk2abbe072003-06-16 23:50:08 +00001469
wdenk3f85ce22004-02-23 16:11:30 +00001470- SystemACE Support:
1471 CONFIG_SYSTEMACE
1472
1473 Adding this option adds support for Xilinx SystemACE
1474 chips attached via some sort of local bus. The address
1475 of the chip must alsh be defined in the
1476 CFG_SYSTEMACE_BASE macro. For example:
1477
1478 #define CONFIG_SYSTEMACE
1479 #define CFG_SYSTEMACE_BASE 0xf0000000
1480
1481 When SystemACE support is added, the "ace" device type
1482 becomes available to the fat commands, i.e. fatls.
1483
wdenka8c7c702003-12-06 19:49:23 +00001484- Show boot progress:
wdenkc6097192002-11-03 00:24:07 +00001485 CONFIG_SHOW_BOOT_PROGRESS
1486
wdenk43d96162003-03-06 00:02:04 +00001487 Defining this option allows to add some board-
1488 specific code (calling a user-provided function
1489 "show_boot_progress(int)") that enables you to show
1490 the system's boot progress on some display (for
1491 example, some LED's) on your board. At the moment,
1492 the following checkpoints are implemented:
wdenkc6097192002-11-03 00:24:07 +00001493
1494 Arg Where When
1495 1 common/cmd_bootm.c before attempting to boot an image
wdenkba56f622004-02-06 23:19:44 +00001496 -1 common/cmd_bootm.c Image header has bad magic number
wdenkc6097192002-11-03 00:24:07 +00001497 2 common/cmd_bootm.c Image header has correct magic number
wdenkba56f622004-02-06 23:19:44 +00001498 -2 common/cmd_bootm.c Image header has bad checksum
wdenkc6097192002-11-03 00:24:07 +00001499 3 common/cmd_bootm.c Image header has correct checksum
wdenkba56f622004-02-06 23:19:44 +00001500 -3 common/cmd_bootm.c Image data has bad checksum
wdenkc6097192002-11-03 00:24:07 +00001501 4 common/cmd_bootm.c Image data has correct checksum
1502 -4 common/cmd_bootm.c Image is for unsupported architecture
1503 5 common/cmd_bootm.c Architecture check OK
1504 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1505 6 common/cmd_bootm.c Image Type check OK
1506 -6 common/cmd_bootm.c gunzip uncompression error
1507 -7 common/cmd_bootm.c Unimplemented compression type
1508 7 common/cmd_bootm.c Uncompression OK
1509 -8 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1510 8 common/cmd_bootm.c Image Type check OK
1511 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
1512 9 common/cmd_bootm.c Start initial ramdisk verification
wdenkba56f622004-02-06 23:19:44 +00001513 -10 common/cmd_bootm.c Ramdisk header has bad magic number
1514 -11 common/cmd_bootm.c Ramdisk header has bad checksum
wdenkc6097192002-11-03 00:24:07 +00001515 10 common/cmd_bootm.c Ramdisk header is OK
wdenkba56f622004-02-06 23:19:44 +00001516 -12 common/cmd_bootm.c Ramdisk data has bad checksum
wdenkc6097192002-11-03 00:24:07 +00001517 11 common/cmd_bootm.c Ramdisk data has correct checksum
1518 12 common/cmd_bootm.c Ramdisk verification complete, start loading
1519 -13 common/cmd_bootm.c Wrong Image Type (not PPC Linux Ramdisk)
1520 13 common/cmd_bootm.c Start multifile image verification
1521 14 common/cmd_bootm.c No initial ramdisk, no multifile, continue.
1522 15 common/cmd_bootm.c All preparation done, transferring control to OS
1523
wdenk11dadd52004-02-27 00:07:27 +00001524 -30 lib_ppc/board.c Fatal error, hang the system
1525 -31 post/post.c POST test failed, detected by post_output_backlog()
1526 -32 post/post.c POST test failed, detected by post_run_single()
wdenk63e73c92004-02-23 22:22:28 +00001527
wdenkc6097192002-11-03 00:24:07 +00001528 -1 common/cmd_doc.c Bad usage of "doc" command
1529 -1 common/cmd_doc.c No boot device
1530 -1 common/cmd_doc.c Unknown Chip ID on boot device
1531 -1 common/cmd_doc.c Read Error on boot device
1532 -1 common/cmd_doc.c Image header has bad magic number
1533
1534 -1 common/cmd_ide.c Bad usage of "ide" command
1535 -1 common/cmd_ide.c No boot device
1536 -1 common/cmd_ide.c Unknown boot device
1537 -1 common/cmd_ide.c Unknown partition table
1538 -1 common/cmd_ide.c Invalid partition type
1539 -1 common/cmd_ide.c Read Error on boot device
1540 -1 common/cmd_ide.c Image header has bad magic number
1541
wdenk206c60c2003-09-18 10:02:25 +00001542 -1 common/cmd_nand.c Bad usage of "nand" command
1543 -1 common/cmd_nand.c No boot device
1544 -1 common/cmd_nand.c Unknown Chip ID on boot device
1545 -1 common/cmd_nand.c Read Error on boot device
1546 -1 common/cmd_nand.c Image header has bad magic number
1547
wdenkba56f622004-02-06 23:19:44 +00001548 -1 common/env_common.c Environment has a bad CRC, using default
wdenkc6097192002-11-03 00:24:07 +00001549
1550
1551Modem Support:
1552--------------
1553
wdenk85ec0bc2003-03-31 16:34:49 +00001554[so far only for SMDK2400 and TRAB boards]
wdenkc6097192002-11-03 00:24:07 +00001555
1556- Modem support endable:
1557 CONFIG_MODEM_SUPPORT
1558
1559- RTS/CTS Flow control enable:
1560 CONFIG_HWFLOW
1561
1562- Modem debug support:
1563 CONFIG_MODEM_SUPPORT_DEBUG
1564
wdenk43d96162003-03-06 00:02:04 +00001565 Enables debugging stuff (char screen[1024], dbg())
1566 for modem support. Useful only with BDI2000.
wdenkc6097192002-11-03 00:24:07 +00001567
wdenka8c7c702003-12-06 19:49:23 +00001568- Interrupt support (PPC):
1569
wdenkd4ca31c2004-01-02 14:00:00 +00001570 There are common interrupt_init() and timer_interrupt()
1571 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
1572 for cpu specific initialization. interrupt_init_cpu()
1573 should set decrementer_count to appropriate value. If
1574 cpu resets decrementer automatically after interrupt
1575 (ppc4xx) it should set decrementer_count to zero.
1576 timer_interrupt() calls timer_interrupt_cpu() for cpu
1577 specific handling. If board has watchdog / status_led
1578 / other_activity_monitor it works automatically from
1579 general timer_interrupt().
wdenka8c7c702003-12-06 19:49:23 +00001580
wdenkc6097192002-11-03 00:24:07 +00001581- General:
1582
wdenk43d96162003-03-06 00:02:04 +00001583 In the target system modem support is enabled when a
1584 specific key (key combination) is pressed during
1585 power-on. Otherwise U-Boot will boot normally
1586 (autoboot). The key_pressed() fuction is called from
1587 board_init(). Currently key_pressed() is a dummy
1588 function, returning 1 and thus enabling modem
1589 initialization.
wdenkc6097192002-11-03 00:24:07 +00001590
wdenk43d96162003-03-06 00:02:04 +00001591 If there are no modem init strings in the
1592 environment, U-Boot proceed to autoboot; the
1593 previous output (banner, info printfs) will be
1594 supressed, though.
wdenkc6097192002-11-03 00:24:07 +00001595
1596 See also: doc/README.Modem
1597
1598
wdenkc6097192002-11-03 00:24:07 +00001599Configuration Settings:
1600-----------------------
1601
1602- CFG_LONGHELP: Defined when you want long help messages included;
1603 undefine this when you're short of memory.
1604
1605- CFG_PROMPT: This is what U-Boot prints on the console to
1606 prompt for user input.
1607
1608- CFG_CBSIZE: Buffer size for input from the Console
1609
1610- CFG_PBSIZE: Buffer size for Console output
1611
1612- CFG_MAXARGS: max. Number of arguments accepted for monitor commands
1613
1614- CFG_BARGSIZE: Buffer size for Boot Arguments which are passed to
1615 the application (usually a Linux kernel) when it is
1616 booted
1617
1618- CFG_BAUDRATE_TABLE:
1619 List of legal baudrate settings for this board.
1620
1621- CFG_CONSOLE_INFO_QUIET
wdenk8bde7f72003-06-27 21:31:46 +00001622 Suppress display of console information at boot.
wdenkc6097192002-11-03 00:24:07 +00001623
1624- CFG_CONSOLE_IS_IN_ENV
wdenk8bde7f72003-06-27 21:31:46 +00001625 If the board specific function
1626 extern int overwrite_console (void);
1627 returns 1, the stdin, stderr and stdout are switched to the
wdenkc6097192002-11-03 00:24:07 +00001628 serial port, else the settings in the environment are used.
1629
1630- CFG_CONSOLE_OVERWRITE_ROUTINE
wdenk8bde7f72003-06-27 21:31:46 +00001631 Enable the call to overwrite_console().
wdenkc6097192002-11-03 00:24:07 +00001632
1633- CFG_CONSOLE_ENV_OVERWRITE
1634 Enable overwrite of previous console environment settings.
1635
1636- CFG_MEMTEST_START, CFG_MEMTEST_END:
1637 Begin and End addresses of the area used by the
1638 simple memory test.
1639
1640- CFG_ALT_MEMTEST:
wdenk8bde7f72003-06-27 21:31:46 +00001641 Enable an alternate, more extensive memory test.
wdenkc6097192002-11-03 00:24:07 +00001642
wdenk5f535fe2003-09-18 09:21:33 +00001643- CFG_MEMTEST_SCRATCH:
1644 Scratch address used by the alternate memory test
1645 You only need to set this if address zero isn't writeable
1646
wdenkc6097192002-11-03 00:24:07 +00001647- CFG_TFTP_LOADADDR:
1648 Default load address for network file downloads
1649
1650- CFG_LOADS_BAUD_CHANGE:
1651 Enable temporary baudrate change while serial download
1652
1653- CFG_SDRAM_BASE:
1654 Physical start address of SDRAM. _Must_ be 0 here.
1655
1656- CFG_MBIO_BASE:
1657 Physical start address of Motherboard I/O (if using a
1658 Cogent motherboard)
1659
1660- CFG_FLASH_BASE:
1661 Physical start address of Flash memory.
1662
1663- CFG_MONITOR_BASE:
1664 Physical start address of boot monitor code (set by
1665 make config files to be same as the text base address
1666 (TEXT_BASE) used when linking) - same as
1667 CFG_FLASH_BASE when booting from flash.
1668
1669- CFG_MONITOR_LEN:
wdenk8bde7f72003-06-27 21:31:46 +00001670 Size of memory reserved for monitor code, used to
1671 determine _at_compile_time_ (!) if the environment is
1672 embedded within the U-Boot image, or in a separate
1673 flash sector.
wdenkc6097192002-11-03 00:24:07 +00001674
1675- CFG_MALLOC_LEN:
1676 Size of DRAM reserved for malloc() use.
1677
1678- CFG_BOOTMAPSZ:
1679 Maximum size of memory mapped by the startup code of
1680 the Linux kernel; all data that must be processed by
1681 the Linux kernel (bd_info, boot arguments, eventually
1682 initrd image) must be put below this limit.
1683
1684- CFG_MAX_FLASH_BANKS:
1685 Max number of Flash memory banks
1686
1687- CFG_MAX_FLASH_SECT:
1688 Max number of sectors on a Flash chip
1689
1690- CFG_FLASH_ERASE_TOUT:
1691 Timeout for Flash erase operations (in ms)
1692
1693- CFG_FLASH_WRITE_TOUT:
1694 Timeout for Flash write operations (in ms)
1695
wdenk8564acf2003-07-14 22:13:32 +00001696- CFG_FLASH_LOCK_TOUT
1697 Timeout for Flash set sector lock bit operation (in ms)
1698
1699- CFG_FLASH_UNLOCK_TOUT
1700 Timeout for Flash clear lock bits operation (in ms)
1701
1702- CFG_FLASH_PROTECTION
1703 If defined, hardware flash sectors protection is used
1704 instead of U-Boot software protection.
1705
wdenkc6097192002-11-03 00:24:07 +00001706- CFG_DIRECT_FLASH_TFTP:
1707
1708 Enable TFTP transfers directly to flash memory;
1709 without this option such a download has to be
1710 performed in two steps: (1) download to RAM, and (2)
1711 copy from RAM to flash.
1712
1713 The two-step approach is usually more reliable, since
1714 you can check if the download worked before you erase
1715 the flash, but in some situations (when sytem RAM is
1716 too limited to allow for a tempory copy of the
1717 downloaded image) this option may be very useful.
1718
1719- CFG_FLASH_CFI:
wdenk43d96162003-03-06 00:02:04 +00001720 Define if the flash driver uses extra elements in the
wdenk5653fc32004-02-08 22:55:38 +00001721 common flash structure for storing flash geometry.
1722
1723- CFG_FLASH_CFI_DRIVER
1724 This option also enables the building of the cfi_flash driver
1725 in the drivers directory
wdenkc6097192002-11-03 00:24:07 +00001726
stroese53cf9432003-06-05 15:39:44 +00001727- CFG_RX_ETH_BUFFER:
1728 Defines the number of ethernet receive buffers. On some
1729 ethernet controllers it is recommended to set this value
1730 to 8 or even higher (EEPRO100 or 405 EMAC), since all
1731 buffers can be full shortly after enabling the interface
1732 on high ethernet traffic.
1733 Defaults to 4 if not defined.
1734
wdenkc6097192002-11-03 00:24:07 +00001735The following definitions that deal with the placement and management
1736of environment data (variable area); in general, we support the
1737following configurations:
1738
1739- CFG_ENV_IS_IN_FLASH:
1740
1741 Define this if the environment is in flash memory.
1742
1743 a) The environment occupies one whole flash sector, which is
1744 "embedded" in the text segment with the U-Boot code. This
1745 happens usually with "bottom boot sector" or "top boot
1746 sector" type flash chips, which have several smaller
1747 sectors at the start or the end. For instance, such a
1748 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
1749 such a case you would place the environment in one of the
1750 4 kB sectors - with U-Boot code before and after it. With
1751 "top boot sector" type flash chips, you would put the
1752 environment in one of the last sectors, leaving a gap
1753 between U-Boot and the environment.
1754
1755 - CFG_ENV_OFFSET:
1756
1757 Offset of environment data (variable area) to the
1758 beginning of flash memory; for instance, with bottom boot
1759 type flash chips the second sector can be used: the offset
1760 for this sector is given here.
1761
1762 CFG_ENV_OFFSET is used relative to CFG_FLASH_BASE.
1763
1764 - CFG_ENV_ADDR:
1765
1766 This is just another way to specify the start address of
1767 the flash sector containing the environment (instead of
1768 CFG_ENV_OFFSET).
1769
1770 - CFG_ENV_SECT_SIZE:
1771
1772 Size of the sector containing the environment.
1773
1774
1775 b) Sometimes flash chips have few, equal sized, BIG sectors.
1776 In such a case you don't want to spend a whole sector for
1777 the environment.
1778
1779 - CFG_ENV_SIZE:
1780
1781 If you use this in combination with CFG_ENV_IS_IN_FLASH
1782 and CFG_ENV_SECT_SIZE, you can specify to use only a part
1783 of this flash sector for the environment. This saves
1784 memory for the RAM copy of the environment.
1785
1786 It may also save flash memory if you decide to use this
1787 when your environment is "embedded" within U-Boot code,
1788 since then the remainder of the flash sector could be used
1789 for U-Boot code. It should be pointed out that this is
1790 STRONGLY DISCOURAGED from a robustness point of view:
1791 updating the environment in flash makes it always
1792 necessary to erase the WHOLE sector. If something goes
1793 wrong before the contents has been restored from a copy in
1794 RAM, your target system will be dead.
1795
1796 - CFG_ENV_ADDR_REDUND
1797 CFG_ENV_SIZE_REDUND
1798
wdenk43d96162003-03-06 00:02:04 +00001799 These settings describe a second storage area used to hold
1800 a redundand copy of the environment data, so that there is
wdenk3e386912003-04-05 00:53:31 +00001801 a valid backup copy in case there is a power failure during
wdenk43d96162003-03-06 00:02:04 +00001802 a "saveenv" operation.
wdenkc6097192002-11-03 00:24:07 +00001803
1804BE CAREFUL! Any changes to the flash layout, and some changes to the
1805source code will make it necessary to adapt <board>/u-boot.lds*
1806accordingly!
1807
1808
1809- CFG_ENV_IS_IN_NVRAM:
1810
1811 Define this if you have some non-volatile memory device
1812 (NVRAM, battery buffered SRAM) which you want to use for the
1813 environment.
1814
1815 - CFG_ENV_ADDR:
1816 - CFG_ENV_SIZE:
1817
1818 These two #defines are used to determin the memory area you
1819 want to use for environment. It is assumed that this memory
1820 can just be read and written to, without any special
1821 provision.
1822
1823BE CAREFUL! The first access to the environment happens quite early
1824in U-Boot initalization (when we try to get the setting of for the
1825console baudrate). You *MUST* have mappend your NVRAM area then, or
1826U-Boot will hang.
1827
1828Please note that even with NVRAM we still use a copy of the
1829environment in RAM: we could work on NVRAM directly, but we want to
1830keep settings there always unmodified except somebody uses "saveenv"
1831to save the current settings.
1832
1833
1834- CFG_ENV_IS_IN_EEPROM:
1835
1836 Use this if you have an EEPROM or similar serial access
1837 device and a driver for it.
1838
1839 - CFG_ENV_OFFSET:
1840 - CFG_ENV_SIZE:
1841
1842 These two #defines specify the offset and size of the
1843 environment area within the total memory of your EEPROM.
1844
1845 - CFG_I2C_EEPROM_ADDR:
1846 If defined, specified the chip address of the EEPROM device.
1847 The default address is zero.
1848
1849 - CFG_EEPROM_PAGE_WRITE_BITS:
1850 If defined, the number of bits used to address bytes in a
1851 single page in the EEPROM device. A 64 byte page, for example
1852 would require six bits.
1853
1854 - CFG_EEPROM_PAGE_WRITE_DELAY_MS:
1855 If defined, the number of milliseconds to delay between
wdenkba56f622004-02-06 23:19:44 +00001856 page writes. The default is zero milliseconds.
wdenkc6097192002-11-03 00:24:07 +00001857
1858 - CFG_I2C_EEPROM_ADDR_LEN:
1859 The length in bytes of the EEPROM memory array address. Note
1860 that this is NOT the chip address length!
1861
wdenk5cf91d62004-04-23 20:32:05 +00001862 - CFG_I2C_EEPROM_ADDR_OVERFLOW:
1863 EEPROM chips that implement "address overflow" are ones
1864 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
1865 address and the extra bits end up in the "chip address" bit
1866 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
1867 byte chips.
1868
1869 Note that we consider the length of the address field to
1870 still be one byte because the extra address bits are hidden
1871 in the chip address.
1872
wdenkc6097192002-11-03 00:24:07 +00001873 - CFG_EEPROM_SIZE:
1874 The size in bytes of the EEPROM device.
1875
wdenkc6097192002-11-03 00:24:07 +00001876
wdenk5779d8d2003-12-06 23:55:10 +00001877- CFG_ENV_IS_IN_DATAFLASH:
1878
wdenkd4ca31c2004-01-02 14:00:00 +00001879 Define this if you have a DataFlash memory device which you
wdenk5779d8d2003-12-06 23:55:10 +00001880 want to use for the environment.
1881
1882 - CFG_ENV_OFFSET:
1883 - CFG_ENV_ADDR:
1884 - CFG_ENV_SIZE:
1885
1886 These three #defines specify the offset and size of the
1887 environment area within the total memory of your DataFlash placed
1888 at the specified address.
1889
wdenk13a56952004-06-09 14:58:14 +00001890- CFG_ENV_IS_IN_NAND:
1891
1892 Define this if you have a NAND device which you want to use
1893 for the environment.
1894
1895 - CFG_ENV_OFFSET:
1896 - CFG_ENV_SIZE:
1897
1898 These two #defines specify the offset and size of the environment
1899 area within the first NAND device.
wdenk5779d8d2003-12-06 23:55:10 +00001900
wdenkc6097192002-11-03 00:24:07 +00001901- CFG_SPI_INIT_OFFSET
1902
1903 Defines offset to the initial SPI buffer area in DPRAM. The
1904 area is used at an early stage (ROM part) if the environment
1905 is configured to reside in the SPI EEPROM: We need a 520 byte
1906 scratch DPRAM area. It is used between the two initialization
1907 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
1908 to be a good choice since it makes it far enough from the
1909 start of the data area as well as from the stack pointer.
1910
1911Please note that the environment is read-only as long as the monitor
1912has been relocated to RAM and a RAM copy of the environment has been
1913created; also, when using EEPROM you will have to use getenv_r()
1914until then to read environment variables.
1915
wdenk85ec0bc2003-03-31 16:34:49 +00001916The environment is protected by a CRC32 checksum. Before the monitor
1917is relocated into RAM, as a result of a bad CRC you will be working
1918with the compiled-in default environment - *silently*!!! [This is
1919necessary, because the first environment variable we need is the
1920"baudrate" setting for the console - if we have a bad CRC, we don't
1921have any device yet where we could complain.]
wdenkc6097192002-11-03 00:24:07 +00001922
1923Note: once the monitor has been relocated, then it will complain if
1924the default environment is used; a new CRC is computed as soon as you
wdenk85ec0bc2003-03-31 16:34:49 +00001925use the "saveenv" command to store a valid environment.
wdenkc6097192002-11-03 00:24:07 +00001926
wdenkfc3e2162003-10-08 22:33:00 +00001927- CFG_FAULT_ECHO_LINK_DOWN:
wdenk42d1f032003-10-15 23:53:47 +00001928 Echo the inverted Ethernet link state to the fault LED.
wdenkfc3e2162003-10-08 22:33:00 +00001929
1930 Note: If this option is active, then CFG_FAULT_MII_ADDR
1931 also needs to be defined.
1932
1933- CFG_FAULT_MII_ADDR:
wdenk42d1f032003-10-15 23:53:47 +00001934 MII address of the PHY to check for the Ethernet link state.
wdenkc6097192002-11-03 00:24:07 +00001935
wdenkc40b2952004-03-13 23:29:43 +00001936- CFG_64BIT_VSPRINTF:
1937 Makes vsprintf (and all *printf functions) support printing
1938 of 64bit values by using the L quantifier
1939
1940- CFG_64BIT_STRTOUL:
1941 Adds simple_strtoull that returns a 64bit value
1942
wdenkc6097192002-11-03 00:24:07 +00001943Low Level (hardware related) configuration options:
wdenkdc7c9a12003-03-26 06:55:25 +00001944---------------------------------------------------
wdenkc6097192002-11-03 00:24:07 +00001945
1946- CFG_CACHELINE_SIZE:
1947 Cache Line Size of the CPU.
1948
1949- CFG_DEFAULT_IMMR:
1950 Default address of the IMMR after system reset.
wdenk2535d602003-07-17 23:16:40 +00001951
wdenk42d1f032003-10-15 23:53:47 +00001952 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
1953 and RPXsuper) to be able to adjust the position of
1954 the IMMR register after a reset.
wdenkc6097192002-11-03 00:24:07 +00001955
wdenk7f6c2cb2002-11-10 22:06:23 +00001956- Floppy Disk Support:
1957 CFG_FDC_DRIVE_NUMBER
1958
1959 the default drive number (default value 0)
1960
1961 CFG_ISA_IO_STRIDE
1962
1963 defines the spacing between fdc chipset registers
1964 (default value 1)
1965
1966 CFG_ISA_IO_OFFSET
1967
wdenk43d96162003-03-06 00:02:04 +00001968 defines the offset of register from address. It
1969 depends on which part of the data bus is connected to
1970 the fdc chipset. (default value 0)
wdenk7f6c2cb2002-11-10 22:06:23 +00001971
wdenk43d96162003-03-06 00:02:04 +00001972 If CFG_ISA_IO_STRIDE CFG_ISA_IO_OFFSET and
1973 CFG_FDC_DRIVE_NUMBER are undefined, they take their
1974 default value.
wdenk7f6c2cb2002-11-10 22:06:23 +00001975
wdenk43d96162003-03-06 00:02:04 +00001976 if CFG_FDC_HW_INIT is defined, then the function
1977 fdc_hw_init() is called at the beginning of the FDC
1978 setup. fdc_hw_init() must be provided by the board
1979 source code. It is used to make hardware dependant
1980 initializations.
wdenk7f6c2cb2002-11-10 22:06:23 +00001981
wdenk25d67122004-12-10 11:40:40 +00001982- CFG_IMMR: Physical address of the Internal Memory.
wdenkefe2a4d2004-12-16 21:44:03 +00001983 DO NOT CHANGE unless you know exactly what you're
wdenk25d67122004-12-10 11:40:40 +00001984 doing! (11-4) [MPC8xx/82xx systems only]
wdenkc6097192002-11-03 00:24:07 +00001985
1986- CFG_INIT_RAM_ADDR:
1987
wdenk7152b1d2003-09-05 23:19:14 +00001988 Start address of memory area that can be used for
wdenkc6097192002-11-03 00:24:07 +00001989 initial data and stack; please note that this must be
1990 writable memory that is working WITHOUT special
1991 initialization, i. e. you CANNOT use normal RAM which
1992 will become available only after programming the
1993 memory controller and running certain initialization
1994 sequences.
1995
1996 U-Boot uses the following memory types:
1997 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
1998 - MPC824X: data cache
1999 - PPC4xx: data cache
2000
wdenk85ec0bc2003-03-31 16:34:49 +00002001- CFG_GBL_DATA_OFFSET:
wdenkc6097192002-11-03 00:24:07 +00002002
2003 Offset of the initial data structure in the memory
2004 area defined by CFG_INIT_RAM_ADDR. Usually
wdenk85ec0bc2003-03-31 16:34:49 +00002005 CFG_GBL_DATA_OFFSET is chosen such that the initial
wdenkc6097192002-11-03 00:24:07 +00002006 data is located at the end of the available space
2007 (sometimes written as (CFG_INIT_RAM_END -
2008 CFG_INIT_DATA_SIZE), and the initial stack is just
2009 below that area (growing from (CFG_INIT_RAM_ADDR +
wdenk85ec0bc2003-03-31 16:34:49 +00002010 CFG_GBL_DATA_OFFSET) downward.
wdenkc6097192002-11-03 00:24:07 +00002011
2012 Note:
2013 On the MPC824X (or other systems that use the data
2014 cache for initial memory) the address chosen for
2015 CFG_INIT_RAM_ADDR is basically arbitrary - it must
2016 point to an otherwise UNUSED address space between
2017 the top of RAM and the start of the PCI space.
2018
2019- CFG_SIUMCR: SIU Module Configuration (11-6)
2020
2021- CFG_SYPCR: System Protection Control (11-9)
2022
2023- CFG_TBSCR: Time Base Status and Control (11-26)
2024
2025- CFG_PISCR: Periodic Interrupt Status and Control (11-31)
2026
2027- CFG_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
2028
2029- CFG_SCCR: System Clock and reset Control Register (15-27)
2030
2031- CFG_OR_TIMING_SDRAM:
2032 SDRAM timing
2033
2034- CFG_MAMR_PTA:
2035 periodic timer for refresh
2036
2037- CFG_DER: Debug Event Register (37-47)
2038
2039- FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CFG_REMAP_OR_AM,
2040 CFG_PRELIM_OR_AM, CFG_OR_TIMING_FLASH, CFG_OR0_REMAP,
2041 CFG_OR0_PRELIM, CFG_BR0_PRELIM, CFG_OR1_REMAP, CFG_OR1_PRELIM,
2042 CFG_BR1_PRELIM:
2043 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
2044
2045- SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
2046 CFG_OR_TIMING_SDRAM, CFG_OR2_PRELIM, CFG_BR2_PRELIM,
2047 CFG_OR3_PRELIM, CFG_BR3_PRELIM:
2048 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
2049
2050- CFG_MAMR_PTA, CFG_MPTPR_2BK_4K, CFG_MPTPR_1BK_4K, CFG_MPTPR_2BK_8K,
2051 CFG_MPTPR_1BK_8K, CFG_MAMR_8COL, CFG_MAMR_9COL:
2052 Machine Mode Register and Memory Periodic Timer
2053 Prescaler definitions (SDRAM timing)
2054
2055- CFG_I2C_UCODE_PATCH, CFG_I2C_DPMEM_OFFSET [0x1FC0]:
2056 enable I2C microcode relocation patch (MPC8xx);
2057 define relocation offset in DPRAM [DSP2]
2058
2059- CFG_SPI_UCODE_PATCH, CFG_SPI_DPMEM_OFFSET [0x1FC0]:
2060 enable SPI microcode relocation patch (MPC8xx);
2061 define relocation offset in DPRAM [SCC4]
2062
2063- CFG_USE_OSCCLK:
2064 Use OSCM clock mode on MBX8xx board. Be careful,
2065 wrong setting might damage your board. Read
2066 doc/README.MBX before setting this variable!
2067
wdenkea909b72002-11-21 23:11:29 +00002068- CFG_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
wdenk43d96162003-03-06 00:02:04 +00002069 Offset of the bootmode word in DPRAM used by post
2070 (Power On Self Tests). This definition overrides
2071 #define'd default value in commproc.h resp.
2072 cpm_8260.h.
wdenkea909b72002-11-21 23:11:29 +00002073
stroese1d49b1f2003-05-23 11:39:05 +00002074- CFG_PCI_SLV_MEM_LOCAL, CFG_PCI_SLV_MEM_BUS, CFG_PICMR0_MASK_ATTRIB,
2075 CFG_PCI_MSTR0_LOCAL, CFG_PCIMSK0_MASK, CFG_PCI_MSTR1_LOCAL,
2076 CFG_PCIMSK1_MASK, CFG_PCI_MSTR_MEM_LOCAL, CFG_PCI_MSTR_MEM_BUS,
2077 CFG_CPU_PCI_MEM_START, CFG_PCI_MSTR_MEM_SIZE, CFG_POCMR0_MASK_ATTRIB,
2078 CFG_PCI_MSTR_MEMIO_LOCAL, CFG_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
2079 CFG_PCI_MSTR_MEMIO_SIZE, CFG_POCMR1_MASK_ATTRIB, CFG_PCI_MSTR_IO_LOCAL,
2080 CFG_PCI_MSTR_IO_BUS, CFG_CPU_PCI_IO_START, CFG_PCI_MSTR_IO_SIZE,
wdenk5d232d02003-05-22 22:52:13 +00002081 CFG_POCMR2_MASK_ATTRIB: (MPC826x only)
2082 Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
2083
wdenkc26e4542004-04-18 10:13:26 +00002084- CONFIG_ETHER_ON_FEC[12]
2085 Define to enable FEC[12] on a 8xx series processor.
2086
2087- CONFIG_FEC[12]_PHY
2088 Define to the hardcoded PHY address which corresponds
wdenk6e592382004-04-18 17:39:38 +00002089 to the given FEC; i. e.
2090 #define CONFIG_FEC1_PHY 4
wdenkc26e4542004-04-18 10:13:26 +00002091 means that the PHY with address 4 is connected to FEC1
2092
2093 When set to -1, means to probe for first available.
2094
2095- CONFIG_FEC[12]_PHY_NORXERR
2096 The PHY does not have a RXERR line (RMII only).
2097 (so program the FEC to ignore it).
2098
2099- CONFIG_RMII
2100 Enable RMII mode for all FECs.
2101 Note that this is a global option, we can't
2102 have one FEC in standard MII mode and another in RMII mode.
2103
wdenk5cf91d62004-04-23 20:32:05 +00002104- CONFIG_CRC32_VERIFY
2105 Add a verify option to the crc32 command.
2106 The syntax is:
2107
2108 => crc32 -v <address> <count> <crc32>
2109
2110 Where address/count indicate a memory area
2111 and crc32 is the correct crc32 which the
2112 area should have.
2113
wdenk56523f12004-07-11 17:40:54 +00002114- CONFIG_LOOPW
2115 Add the "loopw" memory command. This only takes effect if
2116 the memory commands are activated globally (CFG_CMD_MEM).
2117
stroese7b466642004-12-16 18:46:55 +00002118- CONFIG_MX_CYCLIC
2119 Add the "mdc" and "mwc" memory commands. These are cyclic
2120 "md/mw" commands.
2121 Examples:
2122
wdenkefe2a4d2004-12-16 21:44:03 +00002123 => mdc.b 10 4 500
stroese7b466642004-12-16 18:46:55 +00002124 This command will print 4 bytes (10,11,12,13) each 500 ms.
2125
wdenkefe2a4d2004-12-16 21:44:03 +00002126 => mwc.l 100 12345678 10
stroese7b466642004-12-16 18:46:55 +00002127 This command will write 12345678 to address 100 all 10 ms.
2128
wdenkefe2a4d2004-12-16 21:44:03 +00002129 This only takes effect if the memory commands are activated
stroese7b466642004-12-16 18:46:55 +00002130 globally (CFG_CMD_MEM).
2131
wdenk8aa1a2d2005-04-04 12:44:11 +00002132- CONFIG_SKIP_LOWLEVEL_INIT
2133- CONFIG_SKIP_RELOCATE_UBOOT
2134
2135 [ARM only] If these variables are defined, then
2136 certain low level initializations (like setting up
2137 the memory controller) are omitted and/or U-Boot does
2138 not relocate itself into RAM.
2139 Normally these variables MUST NOT be defined. The
2140 only exception is when U-Boot is loaded (to RAM) by
2141 some other boot loader or by a debugger which
2142 performs these intializations itself.
2143
wdenk400558b2005-04-02 23:52:25 +00002144
wdenkc6097192002-11-03 00:24:07 +00002145Building the Software:
2146======================
2147
2148Building U-Boot has been tested in native PPC environments (on a
2149PowerBook G3 running LinuxPPC 2000) and in cross environments
2150(running RedHat 6.x and 7.x Linux on x86, Solaris 2.6 on a SPARC, and
2151NetBSD 1.5 on x86).
2152
2153If you are not using a native PPC environment, it is assumed that you
2154have the GNU cross compiling tools available in your path and named
2155with a prefix of "powerpc-linux-". If this is not the case, (e.g. if
2156you are using Monta Vista's Hard Hat Linux CDK 1.2) you must change
2157the definition of CROSS_COMPILE in Makefile. For HHL on a 4xx CPU,
2158change it to:
2159
2160 CROSS_COMPILE = ppc_4xx-
2161
2162
wdenkba56f622004-02-06 23:19:44 +00002163U-Boot is intended to be simple to build. After installing the
wdenkc6097192002-11-03 00:24:07 +00002164sources you must configure U-Boot for one specific board type. This
2165is done by typing:
2166
2167 make NAME_config
2168
2169where "NAME_config" is the name of one of the existing
2170configurations; the following names are supported:
2171
wdenk1eaeb582004-06-08 00:22:43 +00002172 ADCIOP_config FPS860L_config omap730p2_config
2173 ADS860_config GEN860T_config pcu_e_config
wdenk983fda82004-10-28 00:09:35 +00002174 Alaska8220_config
wdenk1eaeb582004-06-08 00:22:43 +00002175 AR405_config GENIETV_config PIP405_config
2176 at91rm9200dk_config GTH_config QS823_config
2177 CANBT_config hermes_config QS850_config
2178 cmi_mpc5xx_config hymod_config QS860T_config
2179 cogent_common_config IP860_config RPXlite_config
wdenke63c8ee2004-06-09 21:04:48 +00002180 cogent_mpc8260_config IVML24_config RPXlite_DW_config
2181 cogent_mpc8xx_config IVMS8_config RPXsuper_config
2182 CPCI405_config JSE_config rsdproto_config
2183 CPCIISER4_config LANTEC_config Sandpoint8240_config
2184 csb272_config lwmon_config sbc8260_config
wdenk466b7412004-07-10 22:35:59 +00002185 CU824_config MBX860T_config sbc8560_33_config
2186 DUET_ADS_config MBX_config sbc8560_66_config
wdenk8b07a112004-07-10 21:45:47 +00002187 EBONY_config MPC8260ADS_config SM850_config
2188 ELPT860_config MPC8540ADS_config SPD823TS_config
2189 ESTEEM192E_config MPC8560ADS_config stxgp3_config
2190 ETX094_config NETVIA_config SXNI855T_config
2191 FADS823_config omap1510inn_config TQM823L_config
2192 FADS850SAR_config omap1610h2_config TQM850L_config
2193 FADS860T_config omap1610inn_config TQM855L_config
2194 FPS850L_config omap5912osk_config TQM860L_config
wdenk8ed96042005-01-09 23:16:25 +00002195 omap2420h4_config WALNUT405_config
wdenk983fda82004-10-28 00:09:35 +00002196 Yukon8220_config
wdenk8b07a112004-07-10 21:45:47 +00002197 ZPC1900_config
wdenk54387ac2003-10-08 22:45:44 +00002198
wdenk2729af92004-05-03 20:45:30 +00002199Note: for some board special configuration names may exist; check if
2200 additional information is available from the board vendor; for
2201 instance, the TQM823L systems are available without (standard)
2202 or with LCD support. You can select such additional "features"
2203 when chosing the configuration, i. e.
wdenkc6097192002-11-03 00:24:07 +00002204
wdenk2729af92004-05-03 20:45:30 +00002205 make TQM823L_config
2206 - will configure for a plain TQM823L, i. e. no LCD support
wdenkc6097192002-11-03 00:24:07 +00002207
wdenk2729af92004-05-03 20:45:30 +00002208 make TQM823L_LCD_config
2209 - will configure for a TQM823L with U-Boot console on LCD
wdenkc6097192002-11-03 00:24:07 +00002210
wdenk2729af92004-05-03 20:45:30 +00002211 etc.
wdenkc6097192002-11-03 00:24:07 +00002212
wdenkc6097192002-11-03 00:24:07 +00002213
wdenk2729af92004-05-03 20:45:30 +00002214Finally, type "make all", and you should get some working U-Boot
2215images ready for download to / installation on your system:
wdenkc6097192002-11-03 00:24:07 +00002216
wdenk2729af92004-05-03 20:45:30 +00002217- "u-boot.bin" is a raw binary image
2218- "u-boot" is an image in ELF binary format
2219- "u-boot.srec" is in Motorola S-Record format
wdenkc6097192002-11-03 00:24:07 +00002220
wdenkc6097192002-11-03 00:24:07 +00002221
wdenk2729af92004-05-03 20:45:30 +00002222Please be aware that the Makefiles assume you are using GNU make, so
2223for instance on NetBSD you might need to use "gmake" instead of
2224native "make".
wdenkc6097192002-11-03 00:24:07 +00002225
wdenkc6097192002-11-03 00:24:07 +00002226
wdenk2729af92004-05-03 20:45:30 +00002227If the system board that you have is not listed, then you will need
2228to port U-Boot to your hardware platform. To do this, follow these
2229steps:
wdenkc6097192002-11-03 00:24:07 +00002230
wdenk2729af92004-05-03 20:45:30 +000022311. Add a new configuration option for your board to the toplevel
2232 "Makefile" and to the "MAKEALL" script, using the existing
2233 entries as examples. Note that here and at many other places
2234 boards and other names are listed in alphabetical sort order. Please
2235 keep this order.
22362. Create a new directory to hold your board specific code. Add any
2237 files you need. In your board directory, you will need at least
2238 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
22393. Create a new configuration file "include/configs/<board>.h" for
2240 your board
22413. If you're porting U-Boot to a new CPU, then also create a new
2242 directory to hold your CPU specific code. Add any files you need.
22434. Run "make <board>_config" with your new name.
22445. Type "make", and you should get a working "u-boot.srec" file
2245 to be installed on your target system.
22466. Debug and solve any problems that might arise.
2247 [Of course, this last step is much harder than it sounds.]
wdenkc6097192002-11-03 00:24:07 +00002248
wdenkc6097192002-11-03 00:24:07 +00002249
wdenk2729af92004-05-03 20:45:30 +00002250Testing of U-Boot Modifications, Ports to New Hardware, etc.:
2251==============================================================
wdenkc6097192002-11-03 00:24:07 +00002252
wdenk2729af92004-05-03 20:45:30 +00002253If you have modified U-Boot sources (for instance added a new board
2254or support for new devices, a new CPU, etc.) you are expected to
2255provide feedback to the other developers. The feedback normally takes
2256the form of a "patch", i. e. a context diff against a certain (latest
2257official or latest in CVS) version of U-Boot sources.
wdenkc6097192002-11-03 00:24:07 +00002258
wdenk2729af92004-05-03 20:45:30 +00002259But before you submit such a patch, please verify that your modifi-
2260cation did not break existing code. At least make sure that *ALL* of
2261the supported boards compile WITHOUT ANY compiler warnings. To do so,
2262just run the "MAKEALL" script, which will configure and build U-Boot
2263for ALL supported system. Be warned, this will take a while. You can
2264select which (cross) compiler to use by passing a `CROSS_COMPILE'
2265environment variable to the script, i. e. to use the cross tools from
2266MontaVista's Hard Hat Linux you can type
wdenkc6097192002-11-03 00:24:07 +00002267
wdenk2729af92004-05-03 20:45:30 +00002268 CROSS_COMPILE=ppc_8xx- MAKEALL
wdenkc6097192002-11-03 00:24:07 +00002269
wdenk2729af92004-05-03 20:45:30 +00002270or to build on a native PowerPC system you can type
wdenkc6097192002-11-03 00:24:07 +00002271
wdenk2729af92004-05-03 20:45:30 +00002272 CROSS_COMPILE=' ' MAKEALL
wdenkc6097192002-11-03 00:24:07 +00002273
wdenk2729af92004-05-03 20:45:30 +00002274See also "U-Boot Porting Guide" below.
wdenkc6097192002-11-03 00:24:07 +00002275
wdenkc6097192002-11-03 00:24:07 +00002276
wdenk2729af92004-05-03 20:45:30 +00002277Monitor Commands - Overview:
2278============================
wdenkc6097192002-11-03 00:24:07 +00002279
wdenk2729af92004-05-03 20:45:30 +00002280go - start application at address 'addr'
2281run - run commands in an environment variable
2282bootm - boot application image from memory
2283bootp - boot image via network using BootP/TFTP protocol
2284tftpboot- boot image via network using TFTP protocol
2285 and env variables "ipaddr" and "serverip"
2286 (and eventually "gatewayip")
2287rarpboot- boot image via network using RARP/TFTP protocol
2288diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
2289loads - load S-Record file over serial line
2290loadb - load binary file over serial line (kermit mode)
2291md - memory display
2292mm - memory modify (auto-incrementing)
2293nm - memory modify (constant address)
2294mw - memory write (fill)
2295cp - memory copy
2296cmp - memory compare
2297crc32 - checksum calculation
2298imd - i2c memory display
2299imm - i2c memory modify (auto-incrementing)
2300inm - i2c memory modify (constant address)
2301imw - i2c memory write (fill)
2302icrc32 - i2c checksum calculation
2303iprobe - probe to discover valid I2C chip addresses
2304iloop - infinite loop on address range
2305isdram - print SDRAM configuration information
2306sspi - SPI utility commands
2307base - print or set address offset
2308printenv- print environment variables
2309setenv - set environment variables
2310saveenv - save environment variables to persistent storage
2311protect - enable or disable FLASH write protection
2312erase - erase FLASH memory
2313flinfo - print FLASH memory information
2314bdinfo - print Board Info structure
2315iminfo - print header information for application image
2316coninfo - print console devices and informations
2317ide - IDE sub-system
2318loop - infinite loop on address range
wdenk56523f12004-07-11 17:40:54 +00002319loopw - infinite write loop on address range
wdenk2729af92004-05-03 20:45:30 +00002320mtest - simple RAM test
2321icache - enable or disable instruction cache
2322dcache - enable or disable data cache
2323reset - Perform RESET of the CPU
2324echo - echo args to console
2325version - print monitor version
2326help - print online help
2327? - alias for 'help'
wdenkc6097192002-11-03 00:24:07 +00002328
wdenkc6097192002-11-03 00:24:07 +00002329
wdenk2729af92004-05-03 20:45:30 +00002330Monitor Commands - Detailed Description:
2331========================================
wdenkc6097192002-11-03 00:24:07 +00002332
wdenk2729af92004-05-03 20:45:30 +00002333TODO.
wdenkc6097192002-11-03 00:24:07 +00002334
wdenk2729af92004-05-03 20:45:30 +00002335For now: just type "help <command>".
wdenkc6097192002-11-03 00:24:07 +00002336
2337
wdenk2729af92004-05-03 20:45:30 +00002338Environment Variables:
2339======================
wdenkc6097192002-11-03 00:24:07 +00002340
wdenk2729af92004-05-03 20:45:30 +00002341U-Boot supports user configuration using Environment Variables which
2342can be made persistent by saving to Flash memory.
wdenkc6097192002-11-03 00:24:07 +00002343
wdenk2729af92004-05-03 20:45:30 +00002344Environment Variables are set using "setenv", printed using
2345"printenv", and saved to Flash using "saveenv". Using "setenv"
2346without a value can be used to delete a variable from the
2347environment. As long as you don't save the environment you are
2348working with an in-memory copy. In case the Flash area containing the
2349environment is erased by accident, a default environment is provided.
wdenkc6097192002-11-03 00:24:07 +00002350
wdenk2729af92004-05-03 20:45:30 +00002351Some configuration options can be set using Environment Variables:
wdenkc6097192002-11-03 00:24:07 +00002352
wdenk2729af92004-05-03 20:45:30 +00002353 baudrate - see CONFIG_BAUDRATE
wdenkc6097192002-11-03 00:24:07 +00002354
wdenk2729af92004-05-03 20:45:30 +00002355 bootdelay - see CONFIG_BOOTDELAY
wdenkc6097192002-11-03 00:24:07 +00002356
wdenk2729af92004-05-03 20:45:30 +00002357 bootcmd - see CONFIG_BOOTCOMMAND
wdenkc6097192002-11-03 00:24:07 +00002358
wdenk2729af92004-05-03 20:45:30 +00002359 bootargs - Boot arguments when booting an RTOS image
wdenkc6097192002-11-03 00:24:07 +00002360
wdenk2729af92004-05-03 20:45:30 +00002361 bootfile - Name of the image to load with TFTP
wdenkc6097192002-11-03 00:24:07 +00002362
wdenk2729af92004-05-03 20:45:30 +00002363 autoload - if set to "no" (any string beginning with 'n'),
2364 "bootp" will just load perform a lookup of the
2365 configuration from the BOOTP server, but not try to
2366 load any image using TFTP
wdenkc6097192002-11-03 00:24:07 +00002367
wdenk2729af92004-05-03 20:45:30 +00002368 autostart - if set to "yes", an image loaded using the "bootp",
2369 "rarpboot", "tftpboot" or "diskboot" commands will
2370 be automatically started (by internally calling
2371 "bootm")
wdenkc6097192002-11-03 00:24:07 +00002372
wdenk2729af92004-05-03 20:45:30 +00002373 If set to "no", a standalone image passed to the
2374 "bootm" command will be copied to the load address
2375 (and eventually uncompressed), but NOT be started.
2376 This can be used to load and uncompress arbitrary
2377 data.
wdenkc6097192002-11-03 00:24:07 +00002378
wdenk17ea1172004-06-06 21:51:03 +00002379 i2cfast - (PPC405GP|PPC405EP only)
2380 if set to 'y' configures Linux I2C driver for fast
2381 mode (400kHZ). This environment variable is used in
2382 initialization code. So, for changes to be effective
2383 it must be saved and board must be reset.
2384
wdenk2729af92004-05-03 20:45:30 +00002385 initrd_high - restrict positioning of initrd images:
2386 If this variable is not set, initrd images will be
2387 copied to the highest possible address in RAM; this
2388 is usually what you want since it allows for
2389 maximum initrd size. If for some reason you want to
2390 make sure that the initrd image is loaded below the
2391 CFG_BOOTMAPSZ limit, you can set this environment
2392 variable to a value of "no" or "off" or "0".
2393 Alternatively, you can set it to a maximum upper
2394 address to use (U-Boot will still check that it
2395 does not overwrite the U-Boot stack and data).
wdenkc6097192002-11-03 00:24:07 +00002396
wdenk2729af92004-05-03 20:45:30 +00002397 For instance, when you have a system with 16 MB
2398 RAM, and want to reserve 4 MB from use by Linux,
2399 you can do this by adding "mem=12M" to the value of
2400 the "bootargs" variable. However, now you must make
2401 sure that the initrd image is placed in the first
2402 12 MB as well - this can be done with
wdenkc6097192002-11-03 00:24:07 +00002403
wdenk2729af92004-05-03 20:45:30 +00002404 setenv initrd_high 00c00000
wdenkc6097192002-11-03 00:24:07 +00002405
wdenk2729af92004-05-03 20:45:30 +00002406 If you set initrd_high to 0xFFFFFFFF, this is an
2407 indication to U-Boot that all addresses are legal
2408 for the Linux kernel, including addresses in flash
2409 memory. In this case U-Boot will NOT COPY the
2410 ramdisk at all. This may be useful to reduce the
2411 boot time on your system, but requires that this
2412 feature is supported by your Linux kernel.
wdenk4a6fd342003-04-12 23:38:12 +00002413
wdenk2729af92004-05-03 20:45:30 +00002414 ipaddr - IP address; needed for tftpboot command
wdenkc6097192002-11-03 00:24:07 +00002415
wdenk2729af92004-05-03 20:45:30 +00002416 loadaddr - Default load address for commands like "bootp",
2417 "rarpboot", "tftpboot", "loadb" or "diskboot"
wdenkc6097192002-11-03 00:24:07 +00002418
wdenk2729af92004-05-03 20:45:30 +00002419 loads_echo - see CONFIG_LOADS_ECHO
wdenkc6097192002-11-03 00:24:07 +00002420
wdenk2729af92004-05-03 20:45:30 +00002421 serverip - TFTP server IP address; needed for tftpboot command
wdenk38b99262003-05-23 23:18:21 +00002422
wdenk2729af92004-05-03 20:45:30 +00002423 bootretry - see CONFIG_BOOT_RETRY_TIME
wdenkc6097192002-11-03 00:24:07 +00002424
wdenk2729af92004-05-03 20:45:30 +00002425 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
wdenkc6097192002-11-03 00:24:07 +00002426
wdenk2729af92004-05-03 20:45:30 +00002427 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
wdenkc6097192002-11-03 00:24:07 +00002428
wdenk2729af92004-05-03 20:45:30 +00002429 ethprime - When CONFIG_NET_MULTI is enabled controls which
2430 interface is used first.
wdenkc6097192002-11-03 00:24:07 +00002431
wdenk2729af92004-05-03 20:45:30 +00002432 ethact - When CONFIG_NET_MULTI is enabled controls which
2433 interface is currently active. For example you
2434 can do the following
wdenkc6097192002-11-03 00:24:07 +00002435
wdenk2729af92004-05-03 20:45:30 +00002436 => setenv ethact FEC ETHERNET
2437 => ping 192.168.0.1 # traffic sent on FEC ETHERNET
2438 => setenv ethact SCC ETHERNET
2439 => ping 10.0.0.1 # traffic sent on SCC ETHERNET
wdenkc6097192002-11-03 00:24:07 +00002440
wdenk2729af92004-05-03 20:45:30 +00002441 netretry - When set to "no" each network operation will
2442 either succeed or fail without retrying.
2443 When set to "once" the network operation will
2444 fail when all the available network interfaces
2445 are tried once without success.
2446 Useful on scripts which control the retry operation
2447 themselves.
wdenkc6097192002-11-03 00:24:07 +00002448
wdenk2729af92004-05-03 20:45:30 +00002449 vlan - When set to a value < 4095 the traffic over
2450 ethernet is encapsulated/received over 802.1q
2451 VLAN tagged frames.
wdenka3d991b2004-04-15 21:48:45 +00002452
wdenk2729af92004-05-03 20:45:30 +00002453The following environment variables may be used and automatically
2454updated by the network boot commands ("bootp" and "rarpboot"),
2455depending the information provided by your boot server:
wdenka3d991b2004-04-15 21:48:45 +00002456
wdenk2729af92004-05-03 20:45:30 +00002457 bootfile - see above
2458 dnsip - IP address of your Domain Name Server
2459 dnsip2 - IP address of your secondary Domain Name Server
2460 gatewayip - IP address of the Gateway (Router) to use
2461 hostname - Target hostname
2462 ipaddr - see above
2463 netmask - Subnet Mask
2464 rootpath - Pathname of the root filesystem on the NFS server
2465 serverip - see above
wdenka3d991b2004-04-15 21:48:45 +00002466
wdenka3d991b2004-04-15 21:48:45 +00002467
wdenk2729af92004-05-03 20:45:30 +00002468There are two special Environment Variables:
wdenkc6097192002-11-03 00:24:07 +00002469
wdenk2729af92004-05-03 20:45:30 +00002470 serial# - contains hardware identification information such
2471 as type string and/or serial number
2472 ethaddr - Ethernet address
wdenkc6097192002-11-03 00:24:07 +00002473
wdenk2729af92004-05-03 20:45:30 +00002474These variables can be set only once (usually during manufacturing of
2475the board). U-Boot refuses to delete or overwrite these variables
2476once they have been set once.
wdenkc6097192002-11-03 00:24:07 +00002477
2478
wdenk2729af92004-05-03 20:45:30 +00002479Further special Environment Variables:
wdenkc6097192002-11-03 00:24:07 +00002480
wdenk2729af92004-05-03 20:45:30 +00002481 ver - Contains the U-Boot version string as printed
2482 with the "version" command. This variable is
2483 readonly (see CONFIG_VERSION_VARIABLE).
wdenkc6097192002-11-03 00:24:07 +00002484
wdenkc6097192002-11-03 00:24:07 +00002485
wdenk2729af92004-05-03 20:45:30 +00002486Please note that changes to some configuration parameters may take
2487only effect after the next boot (yes, that's just like Windoze :-).
wdenkc6097192002-11-03 00:24:07 +00002488
stroesec1551ea2003-04-04 15:53:41 +00002489
wdenk2729af92004-05-03 20:45:30 +00002490Command Line Parsing:
2491=====================
stroesec1551ea2003-04-04 15:53:41 +00002492
wdenk2729af92004-05-03 20:45:30 +00002493There are two different command line parsers available with U-Boot:
2494the old "simple" one, and the much more powerful "hush" shell:
stroesec1551ea2003-04-04 15:53:41 +00002495
wdenk2729af92004-05-03 20:45:30 +00002496Old, simple command line parser:
2497--------------------------------
wdenkc6097192002-11-03 00:24:07 +00002498
wdenk2729af92004-05-03 20:45:30 +00002499- supports environment variables (through setenv / saveenv commands)
2500- several commands on one line, separated by ';'
2501- variable substitution using "... $(name) ..." syntax
2502- special characters ('$', ';') can be escaped by prefixing with '\',
2503 for example:
2504 setenv bootcmd bootm \$(address)
2505- You can also escape text by enclosing in single apostrophes, for example:
2506 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
wdenkc6097192002-11-03 00:24:07 +00002507
wdenk2729af92004-05-03 20:45:30 +00002508Hush shell:
2509-----------
wdenkf07771c2003-05-28 08:06:31 +00002510
wdenk2729af92004-05-03 20:45:30 +00002511- similar to Bourne shell, with control structures like
2512 if...then...else...fi, for...do...done; while...do...done,
2513 until...do...done, ...
2514- supports environment ("global") variables (through setenv / saveenv
2515 commands) and local shell variables (through standard shell syntax
2516 "name=value"); only environment variables can be used with "run"
2517 command
wdenkf07771c2003-05-28 08:06:31 +00002518
wdenk2729af92004-05-03 20:45:30 +00002519General rules:
2520--------------
wdenkf07771c2003-05-28 08:06:31 +00002521
wdenk2729af92004-05-03 20:45:30 +00002522(1) If a command line (or an environment variable executed by a "run"
2523 command) contains several commands separated by semicolon, and
2524 one of these commands fails, then the remaining commands will be
2525 executed anyway.
wdenkf07771c2003-05-28 08:06:31 +00002526
wdenk2729af92004-05-03 20:45:30 +00002527(2) If you execute several variables with one call to run (i. e.
2528 calling run with a list af variables as arguments), any failing
2529 command will cause "run" to terminate, i. e. the remaining
2530 variables are not executed.
wdenkf07771c2003-05-28 08:06:31 +00002531
wdenk2729af92004-05-03 20:45:30 +00002532Note for Redundant Ethernet Interfaces:
2533=======================================
wdenkf07771c2003-05-28 08:06:31 +00002534
wdenk2729af92004-05-03 20:45:30 +00002535Some boards come with redundant ethernet interfaces; U-Boot supports
2536such configurations and is capable of automatic selection of a
2537"working" interface when needed. MAC assignment works as follows:
wdenkf07771c2003-05-28 08:06:31 +00002538
wdenk2729af92004-05-03 20:45:30 +00002539Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
2540MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
2541"eth1addr" (=>eth1), "eth2addr", ...
wdenkf07771c2003-05-28 08:06:31 +00002542
wdenk2729af92004-05-03 20:45:30 +00002543If the network interface stores some valid MAC address (for instance
2544in SROM), this is used as default address if there is NO correspon-
2545ding setting in the environment; if the corresponding environment
2546variable is set, this overrides the settings in the card; that means:
wdenkf07771c2003-05-28 08:06:31 +00002547
wdenk2729af92004-05-03 20:45:30 +00002548o If the SROM has a valid MAC address, and there is no address in the
2549 environment, the SROM's address is used.
wdenkc6097192002-11-03 00:24:07 +00002550
wdenk2729af92004-05-03 20:45:30 +00002551o If there is no valid address in the SROM, and a definition in the
2552 environment exists, then the value from the environment variable is
2553 used.
wdenkc6097192002-11-03 00:24:07 +00002554
wdenk2729af92004-05-03 20:45:30 +00002555o If both the SROM and the environment contain a MAC address, and
2556 both addresses are the same, this MAC address is used.
wdenkc6097192002-11-03 00:24:07 +00002557
wdenk2729af92004-05-03 20:45:30 +00002558o If both the SROM and the environment contain a MAC address, and the
2559 addresses differ, the value from the environment is used and a
2560 warning is printed.
wdenkc6097192002-11-03 00:24:07 +00002561
wdenk2729af92004-05-03 20:45:30 +00002562o If neither SROM nor the environment contain a MAC address, an error
2563 is raised.
wdenkc6097192002-11-03 00:24:07 +00002564
wdenkc6097192002-11-03 00:24:07 +00002565
wdenk2729af92004-05-03 20:45:30 +00002566Image Formats:
2567==============
wdenkc6097192002-11-03 00:24:07 +00002568
wdenk2729af92004-05-03 20:45:30 +00002569The "boot" commands of this monitor operate on "image" files which
2570can be basicly anything, preceeded by a special header; see the
2571definitions in include/image.h for details; basicly, the header
2572defines the following image properties:
wdenkc6097192002-11-03 00:24:07 +00002573
wdenk2729af92004-05-03 20:45:30 +00002574* Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
2575 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
2576 LynxOS, pSOS, QNX, RTEMS, ARTOS;
2577 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS, LynxOS).
2578* Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,
2579 IA64, MIPS, NIOS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
2580 Currently supported: ARM, Intel x86, MIPS, NIOS, PowerPC).
2581* Compression Type (uncompressed, gzip, bzip2)
2582* Load Address
2583* Entry Point
2584* Image Name
2585* Image Timestamp
wdenkc6097192002-11-03 00:24:07 +00002586
wdenk2729af92004-05-03 20:45:30 +00002587The header is marked by a special Magic Number, and both the header
2588and the data portions of the image are secured against corruption by
2589CRC32 checksums.
wdenkc6097192002-11-03 00:24:07 +00002590
wdenkc6097192002-11-03 00:24:07 +00002591
wdenk2729af92004-05-03 20:45:30 +00002592Linux Support:
2593==============
wdenkc6097192002-11-03 00:24:07 +00002594
wdenk2729af92004-05-03 20:45:30 +00002595Although U-Boot should support any OS or standalone application
2596easily, the main focus has always been on Linux during the design of
2597U-Boot.
wdenkc6097192002-11-03 00:24:07 +00002598
wdenk2729af92004-05-03 20:45:30 +00002599U-Boot includes many features that so far have been part of some
2600special "boot loader" code within the Linux kernel. Also, any
2601"initrd" images to be used are no longer part of one big Linux image;
2602instead, kernel and "initrd" are separate images. This implementation
2603serves several purposes:
wdenkc6097192002-11-03 00:24:07 +00002604
wdenk2729af92004-05-03 20:45:30 +00002605- the same features can be used for other OS or standalone
2606 applications (for instance: using compressed images to reduce the
2607 Flash memory footprint)
wdenkc6097192002-11-03 00:24:07 +00002608
wdenk2729af92004-05-03 20:45:30 +00002609- it becomes much easier to port new Linux kernel versions because
2610 lots of low-level, hardware dependent stuff are done by U-Boot
wdenkc6097192002-11-03 00:24:07 +00002611
wdenk2729af92004-05-03 20:45:30 +00002612- the same Linux kernel image can now be used with different "initrd"
2613 images; of course this also means that different kernel images can
2614 be run with the same "initrd". This makes testing easier (you don't
2615 have to build a new "zImage.initrd" Linux image when you just
2616 change a file in your "initrd"). Also, a field-upgrade of the
2617 software is easier now.
wdenkc6097192002-11-03 00:24:07 +00002618
wdenkc6097192002-11-03 00:24:07 +00002619
wdenk2729af92004-05-03 20:45:30 +00002620Linux HOWTO:
2621============
wdenkc6097192002-11-03 00:24:07 +00002622
wdenk2729af92004-05-03 20:45:30 +00002623Porting Linux to U-Boot based systems:
2624---------------------------------------
wdenkc6097192002-11-03 00:24:07 +00002625
wdenk2729af92004-05-03 20:45:30 +00002626U-Boot cannot save you from doing all the necessary modifications to
2627configure the Linux device drivers for use with your target hardware
2628(no, we don't intend to provide a full virtual machine interface to
2629Linux :-).
wdenkc6097192002-11-03 00:24:07 +00002630
wdenk2729af92004-05-03 20:45:30 +00002631But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
wdenkc6097192002-11-03 00:24:07 +00002632
wdenk2729af92004-05-03 20:45:30 +00002633Just make sure your machine specific header file (for instance
2634include/asm-ppc/tqm8xx.h) includes the same definition of the Board
2635Information structure as we define in include/u-boot.h, and make
2636sure that your definition of IMAP_ADDR uses the same value as your
2637U-Boot configuration in CFG_IMMR.
wdenkc6097192002-11-03 00:24:07 +00002638
wdenkc6097192002-11-03 00:24:07 +00002639
wdenk2729af92004-05-03 20:45:30 +00002640Configuring the Linux kernel:
2641-----------------------------
wdenkc6097192002-11-03 00:24:07 +00002642
wdenk2729af92004-05-03 20:45:30 +00002643No specific requirements for U-Boot. Make sure you have some root
2644device (initial ramdisk, NFS) for your target system.
wdenkc6097192002-11-03 00:24:07 +00002645
wdenkc6097192002-11-03 00:24:07 +00002646
wdenk2729af92004-05-03 20:45:30 +00002647Building a Linux Image:
2648-----------------------
wdenkc6097192002-11-03 00:24:07 +00002649
wdenk2729af92004-05-03 20:45:30 +00002650With U-Boot, "normal" build targets like "zImage" or "bzImage" are
2651not used. If you use recent kernel source, a new build target
2652"uImage" will exist which automatically builds an image usable by
2653U-Boot. Most older kernels also have support for a "pImage" target,
2654which was introduced for our predecessor project PPCBoot and uses a
2655100% compatible format.
wdenkc6097192002-11-03 00:24:07 +00002656
wdenk2729af92004-05-03 20:45:30 +00002657Example:
wdenkc6097192002-11-03 00:24:07 +00002658
wdenk2729af92004-05-03 20:45:30 +00002659 make TQM850L_config
2660 make oldconfig
2661 make dep
2662 make uImage
wdenkc6097192002-11-03 00:24:07 +00002663
wdenk2729af92004-05-03 20:45:30 +00002664The "uImage" build target uses a special tool (in 'tools/mkimage') to
2665encapsulate a compressed Linux kernel image with header information,
2666CRC32 checksum etc. for use with U-Boot. This is what we are doing:
wdenkc6097192002-11-03 00:24:07 +00002667
wdenk2729af92004-05-03 20:45:30 +00002668* build a standard "vmlinux" kernel image (in ELF binary format):
wdenkc6097192002-11-03 00:24:07 +00002669
wdenk2729af92004-05-03 20:45:30 +00002670* convert the kernel into a raw binary image:
wdenkc6097192002-11-03 00:24:07 +00002671
wdenk2729af92004-05-03 20:45:30 +00002672 ${CROSS_COMPILE}-objcopy -O binary \
2673 -R .note -R .comment \
2674 -S vmlinux linux.bin
wdenkc6097192002-11-03 00:24:07 +00002675
wdenk2729af92004-05-03 20:45:30 +00002676* compress the binary image:
wdenkc6097192002-11-03 00:24:07 +00002677
wdenk2729af92004-05-03 20:45:30 +00002678 gzip -9 linux.bin
wdenkc6097192002-11-03 00:24:07 +00002679
wdenk2729af92004-05-03 20:45:30 +00002680* package compressed binary image for U-Boot:
wdenk24ee89b2002-11-03 17:56:27 +00002681
wdenk2729af92004-05-03 20:45:30 +00002682 mkimage -A ppc -O linux -T kernel -C gzip \
2683 -a 0 -e 0 -n "Linux Kernel Image" \
2684 -d linux.bin.gz uImage
wdenk24ee89b2002-11-03 17:56:27 +00002685
wdenk24ee89b2002-11-03 17:56:27 +00002686
wdenk2729af92004-05-03 20:45:30 +00002687The "mkimage" tool can also be used to create ramdisk images for use
2688with U-Boot, either separated from the Linux kernel image, or
2689combined into one file. "mkimage" encapsulates the images with a 64
2690byte header containing information about target architecture,
2691operating system, image type, compression method, entry points, time
2692stamp, CRC32 checksums, etc.
wdenk24ee89b2002-11-03 17:56:27 +00002693
wdenk2729af92004-05-03 20:45:30 +00002694"mkimage" can be called in two ways: to verify existing images and
2695print the header information, or to build new images.
wdenk24ee89b2002-11-03 17:56:27 +00002696
wdenk2729af92004-05-03 20:45:30 +00002697In the first form (with "-l" option) mkimage lists the information
2698contained in the header of an existing U-Boot image; this includes
2699checksum verification:
wdenk24ee89b2002-11-03 17:56:27 +00002700
wdenk2729af92004-05-03 20:45:30 +00002701 tools/mkimage -l image
2702 -l ==> list image header information
wdenk24ee89b2002-11-03 17:56:27 +00002703
wdenk2729af92004-05-03 20:45:30 +00002704The second form (with "-d" option) is used to build a U-Boot image
2705from a "data file" which is used as image payload:
wdenk24ee89b2002-11-03 17:56:27 +00002706
wdenk2729af92004-05-03 20:45:30 +00002707 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
2708 -n name -d data_file image
2709 -A ==> set architecture to 'arch'
2710 -O ==> set operating system to 'os'
2711 -T ==> set image type to 'type'
2712 -C ==> set compression type 'comp'
2713 -a ==> set load address to 'addr' (hex)
2714 -e ==> set entry point to 'ep' (hex)
2715 -n ==> set image name to 'name'
2716 -d ==> use image data from 'datafile'
wdenk24ee89b2002-11-03 17:56:27 +00002717
wdenk69459792004-05-29 16:53:29 +00002718Right now, all Linux kernels for PowerPC systems use the same load
2719address (0x00000000), but the entry point address depends on the
2720kernel version:
wdenkc6097192002-11-03 00:24:07 +00002721
wdenk2729af92004-05-03 20:45:30 +00002722- 2.2.x kernels have the entry point at 0x0000000C,
2723- 2.3.x and later kernels have the entry point at 0x00000000.
wdenkc6097192002-11-03 00:24:07 +00002724
wdenk2729af92004-05-03 20:45:30 +00002725So a typical call to build a U-Boot image would read:
wdenkc6097192002-11-03 00:24:07 +00002726
wdenk2729af92004-05-03 20:45:30 +00002727 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2728 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
2729 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
2730 > examples/uImage.TQM850L
2731 Image Name: 2.4.4 kernel for TQM850L
2732 Created: Wed Jul 19 02:34:59 2000
2733 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2734 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2735 Load Address: 0x00000000
2736 Entry Point: 0x00000000
wdenkc6097192002-11-03 00:24:07 +00002737
wdenk2729af92004-05-03 20:45:30 +00002738To verify the contents of the image (or check for corruption):
wdenkc6097192002-11-03 00:24:07 +00002739
wdenk2729af92004-05-03 20:45:30 +00002740 -> tools/mkimage -l examples/uImage.TQM850L
2741 Image Name: 2.4.4 kernel for TQM850L
2742 Created: Wed Jul 19 02:34:59 2000
2743 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2744 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2745 Load Address: 0x00000000
2746 Entry Point: 0x00000000
wdenkc6097192002-11-03 00:24:07 +00002747
wdenk2729af92004-05-03 20:45:30 +00002748NOTE: for embedded systems where boot time is critical you can trade
2749speed for memory and install an UNCOMPRESSED image instead: this
2750needs more space in Flash, but boots much faster since it does not
2751need to be uncompressed:
wdenkc6097192002-11-03 00:24:07 +00002752
wdenk2729af92004-05-03 20:45:30 +00002753 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
2754 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2755 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
2756 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
2757 > examples/uImage.TQM850L-uncompressed
2758 Image Name: 2.4.4 kernel for TQM850L
2759 Created: Wed Jul 19 02:34:59 2000
2760 Image Type: PowerPC Linux Kernel Image (uncompressed)
2761 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
2762 Load Address: 0x00000000
2763 Entry Point: 0x00000000
wdenkc6097192002-11-03 00:24:07 +00002764
wdenkc6097192002-11-03 00:24:07 +00002765
wdenk2729af92004-05-03 20:45:30 +00002766Similar you can build U-Boot images from a 'ramdisk.image.gz' file
2767when your kernel is intended to use an initial ramdisk:
wdenkdb01a2e2004-04-15 23:14:49 +00002768
wdenk2729af92004-05-03 20:45:30 +00002769 -> tools/mkimage -n 'Simple Ramdisk Image' \
2770 > -A ppc -O linux -T ramdisk -C gzip \
2771 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
2772 Image Name: Simple Ramdisk Image
2773 Created: Wed Jan 12 14:01:50 2000
2774 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2775 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
2776 Load Address: 0x00000000
2777 Entry Point: 0x00000000
wdenkdb01a2e2004-04-15 23:14:49 +00002778
wdenkdb01a2e2004-04-15 23:14:49 +00002779
wdenk2729af92004-05-03 20:45:30 +00002780Installing a Linux Image:
2781-------------------------
wdenkdb01a2e2004-04-15 23:14:49 +00002782
wdenk2729af92004-05-03 20:45:30 +00002783To downloading a U-Boot image over the serial (console) interface,
2784you must convert the image to S-Record format:
wdenkdb01a2e2004-04-15 23:14:49 +00002785
wdenk2729af92004-05-03 20:45:30 +00002786 objcopy -I binary -O srec examples/image examples/image.srec
wdenkdb01a2e2004-04-15 23:14:49 +00002787
wdenk2729af92004-05-03 20:45:30 +00002788The 'objcopy' does not understand the information in the U-Boot
2789image header, so the resulting S-Record file will be relative to
2790address 0x00000000. To load it to a given address, you need to
2791specify the target address as 'offset' parameter with the 'loads'
2792command.
wdenkc6097192002-11-03 00:24:07 +00002793
wdenk2729af92004-05-03 20:45:30 +00002794Example: install the image to address 0x40100000 (which on the
2795TQM8xxL is in the first Flash bank):
wdenkc6097192002-11-03 00:24:07 +00002796
wdenk2729af92004-05-03 20:45:30 +00002797 => erase 40100000 401FFFFF
wdenkc6097192002-11-03 00:24:07 +00002798
wdenk2729af92004-05-03 20:45:30 +00002799 .......... done
2800 Erased 8 sectors
wdenkc6097192002-11-03 00:24:07 +00002801
wdenk2729af92004-05-03 20:45:30 +00002802 => loads 40100000
2803 ## Ready for S-Record download ...
2804 ~>examples/image.srec
2805 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
2806 ...
2807 15989 15990 15991 15992
2808 [file transfer complete]
2809 [connected]
2810 ## Start Addr = 0x00000000
wdenkc6097192002-11-03 00:24:07 +00002811
2812
wdenk2729af92004-05-03 20:45:30 +00002813You can check the success of the download using the 'iminfo' command;
2814this includes a checksum verification so you can be sure no data
2815corruption happened:
wdenkc6097192002-11-03 00:24:07 +00002816
wdenk2729af92004-05-03 20:45:30 +00002817 => imi 40100000
wdenkc6097192002-11-03 00:24:07 +00002818
wdenk2729af92004-05-03 20:45:30 +00002819 ## Checking Image at 40100000 ...
2820 Image Name: 2.2.13 for initrd on TQM850L
2821 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2822 Data Size: 335725 Bytes = 327 kB = 0 MB
2823 Load Address: 00000000
2824 Entry Point: 0000000c
2825 Verifying Checksum ... OK
wdenkc6097192002-11-03 00:24:07 +00002826
2827
wdenk2729af92004-05-03 20:45:30 +00002828Boot Linux:
2829-----------
wdenkc6097192002-11-03 00:24:07 +00002830
wdenk2729af92004-05-03 20:45:30 +00002831The "bootm" command is used to boot an application that is stored in
2832memory (RAM or Flash). In case of a Linux kernel image, the contents
2833of the "bootargs" environment variable is passed to the kernel as
2834parameters. You can check and modify this variable using the
2835"printenv" and "setenv" commands:
wdenkc6097192002-11-03 00:24:07 +00002836
2837
wdenk2729af92004-05-03 20:45:30 +00002838 => printenv bootargs
2839 bootargs=root=/dev/ram
wdenkc6097192002-11-03 00:24:07 +00002840
wdenk2729af92004-05-03 20:45:30 +00002841 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
wdenkc6097192002-11-03 00:24:07 +00002842
wdenk2729af92004-05-03 20:45:30 +00002843 => printenv bootargs
2844 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
wdenkc6097192002-11-03 00:24:07 +00002845
wdenk2729af92004-05-03 20:45:30 +00002846 => bootm 40020000
2847 ## Booting Linux kernel at 40020000 ...
2848 Image Name: 2.2.13 for NFS on TQM850L
2849 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2850 Data Size: 381681 Bytes = 372 kB = 0 MB
2851 Load Address: 00000000
2852 Entry Point: 0000000c
2853 Verifying Checksum ... OK
2854 Uncompressing Kernel Image ... OK
2855 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
2856 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2857 time_init: decrementer frequency = 187500000/60
2858 Calibrating delay loop... 49.77 BogoMIPS
2859 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
2860 ...
wdenkc6097192002-11-03 00:24:07 +00002861
wdenk2729af92004-05-03 20:45:30 +00002862If you want to boot a Linux kernel with initial ram disk, you pass
2863the memory addresses of both the kernel and the initrd image (PPBCOOT
2864format!) to the "bootm" command:
wdenkc6097192002-11-03 00:24:07 +00002865
wdenk2729af92004-05-03 20:45:30 +00002866 => imi 40100000 40200000
wdenkc6097192002-11-03 00:24:07 +00002867
wdenk2729af92004-05-03 20:45:30 +00002868 ## Checking Image at 40100000 ...
2869 Image Name: 2.2.13 for initrd on TQM850L
2870 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2871 Data Size: 335725 Bytes = 327 kB = 0 MB
2872 Load Address: 00000000
2873 Entry Point: 0000000c
2874 Verifying Checksum ... OK
wdenkc6097192002-11-03 00:24:07 +00002875
wdenk2729af92004-05-03 20:45:30 +00002876 ## Checking Image at 40200000 ...
2877 Image Name: Simple Ramdisk Image
2878 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2879 Data Size: 566530 Bytes = 553 kB = 0 MB
2880 Load Address: 00000000
2881 Entry Point: 00000000
2882 Verifying Checksum ... OK
wdenkc6097192002-11-03 00:24:07 +00002883
wdenk2729af92004-05-03 20:45:30 +00002884 => bootm 40100000 40200000
2885 ## Booting Linux kernel at 40100000 ...
2886 Image Name: 2.2.13 for initrd on TQM850L
2887 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2888 Data Size: 335725 Bytes = 327 kB = 0 MB
2889 Load Address: 00000000
2890 Entry Point: 0000000c
2891 Verifying Checksum ... OK
2892 Uncompressing Kernel Image ... OK
2893 ## Loading RAMDisk Image at 40200000 ...
2894 Image Name: Simple Ramdisk Image
2895 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2896 Data Size: 566530 Bytes = 553 kB = 0 MB
2897 Load Address: 00000000
2898 Entry Point: 00000000
2899 Verifying Checksum ... OK
2900 Loading Ramdisk ... OK
2901 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
2902 Boot arguments: root=/dev/ram
2903 time_init: decrementer frequency = 187500000/60
2904 Calibrating delay loop... 49.77 BogoMIPS
2905 ...
2906 RAMDISK: Compressed image found at block 0
2907 VFS: Mounted root (ext2 filesystem).
wdenkc6097192002-11-03 00:24:07 +00002908
wdenk2729af92004-05-03 20:45:30 +00002909 bash#
wdenkc6097192002-11-03 00:24:07 +00002910
wdenk2729af92004-05-03 20:45:30 +00002911More About U-Boot Image Types:
2912------------------------------
wdenk6069ff22003-02-28 00:49:47 +00002913
wdenk2729af92004-05-03 20:45:30 +00002914U-Boot supports the following image types:
wdenk6069ff22003-02-28 00:49:47 +00002915
wdenk2729af92004-05-03 20:45:30 +00002916 "Standalone Programs" are directly runnable in the environment
2917 provided by U-Boot; it is expected that (if they behave
2918 well) you can continue to work in U-Boot after return from
2919 the Standalone Program.
2920 "OS Kernel Images" are usually images of some Embedded OS which
2921 will take over control completely. Usually these programs
2922 will install their own set of exception handlers, device
2923 drivers, set up the MMU, etc. - this means, that you cannot
2924 expect to re-enter U-Boot except by resetting the CPU.
2925 "RAMDisk Images" are more or less just data blocks, and their
2926 parameters (address, size) are passed to an OS kernel that is
2927 being started.
2928 "Multi-File Images" contain several images, typically an OS
2929 (Linux) kernel image and one or more data images like
2930 RAMDisks. This construct is useful for instance when you want
2931 to boot over the network using BOOTP etc., where the boot
2932 server provides just a single image file, but you want to get
2933 for instance an OS kernel and a RAMDisk image.
stroesec1551ea2003-04-04 15:53:41 +00002934
wdenk2729af92004-05-03 20:45:30 +00002935 "Multi-File Images" start with a list of image sizes, each
2936 image size (in bytes) specified by an "uint32_t" in network
2937 byte order. This list is terminated by an "(uint32_t)0".
2938 Immediately after the terminating 0 follow the images, one by
2939 one, all aligned on "uint32_t" boundaries (size rounded up to
2940 a multiple of 4 bytes).
stroesec1551ea2003-04-04 15:53:41 +00002941
wdenk2729af92004-05-03 20:45:30 +00002942 "Firmware Images" are binary images containing firmware (like
2943 U-Boot or FPGA images) which usually will be programmed to
2944 flash memory.
stroesec1551ea2003-04-04 15:53:41 +00002945
wdenk2729af92004-05-03 20:45:30 +00002946 "Script files" are command sequences that will be executed by
2947 U-Boot's command interpreter; this feature is especially
2948 useful when you configure U-Boot to use a real shell (hush)
2949 as command interpreter.
wdenk6069ff22003-02-28 00:49:47 +00002950
wdenkc6097192002-11-03 00:24:07 +00002951
wdenk2729af92004-05-03 20:45:30 +00002952Standalone HOWTO:
2953=================
wdenkc6097192002-11-03 00:24:07 +00002954
wdenk2729af92004-05-03 20:45:30 +00002955One of the features of U-Boot is that you can dynamically load and
2956run "standalone" applications, which can use some resources of
2957U-Boot like console I/O functions or interrupt services.
wdenkc6097192002-11-03 00:24:07 +00002958
wdenk2729af92004-05-03 20:45:30 +00002959Two simple examples are included with the sources:
wdenkc6097192002-11-03 00:24:07 +00002960
wdenk2729af92004-05-03 20:45:30 +00002961"Hello World" Demo:
2962-------------------
wdenkc6097192002-11-03 00:24:07 +00002963
wdenk2729af92004-05-03 20:45:30 +00002964'examples/hello_world.c' contains a small "Hello World" Demo
2965application; it is automatically compiled when you build U-Boot.
2966It's configured to run at address 0x00040004, so you can play with it
2967like that:
wdenkc6097192002-11-03 00:24:07 +00002968
wdenk2729af92004-05-03 20:45:30 +00002969 => loads
2970 ## Ready for S-Record download ...
2971 ~>examples/hello_world.srec
2972 1 2 3 4 5 6 7 8 9 10 11 ...
2973 [file transfer complete]
2974 [connected]
2975 ## Start Addr = 0x00040004
wdenkc6097192002-11-03 00:24:07 +00002976
wdenk2729af92004-05-03 20:45:30 +00002977 => go 40004 Hello World! This is a test.
2978 ## Starting application at 0x00040004 ...
2979 Hello World
2980 argc = 7
2981 argv[0] = "40004"
2982 argv[1] = "Hello"
2983 argv[2] = "World!"
2984 argv[3] = "This"
2985 argv[4] = "is"
2986 argv[5] = "a"
2987 argv[6] = "test."
2988 argv[7] = "<NULL>"
2989 Hit any key to exit ...
wdenkc6097192002-11-03 00:24:07 +00002990
wdenk2729af92004-05-03 20:45:30 +00002991 ## Application terminated, rc = 0x0
wdenkc6097192002-11-03 00:24:07 +00002992
wdenk2729af92004-05-03 20:45:30 +00002993Another example, which demonstrates how to register a CPM interrupt
2994handler with the U-Boot code, can be found in 'examples/timer.c'.
2995Here, a CPM timer is set up to generate an interrupt every second.
2996The interrupt service routine is trivial, just printing a '.'
2997character, but this is just a demo program. The application can be
2998controlled by the following keys:
wdenkc6097192002-11-03 00:24:07 +00002999
wdenk2729af92004-05-03 20:45:30 +00003000 ? - print current values og the CPM Timer registers
3001 b - enable interrupts and start timer
3002 e - stop timer and disable interrupts
3003 q - quit application
wdenkc6097192002-11-03 00:24:07 +00003004
wdenk2729af92004-05-03 20:45:30 +00003005 => loads
3006 ## Ready for S-Record download ...
3007 ~>examples/timer.srec
3008 1 2 3 4 5 6 7 8 9 10 11 ...
3009 [file transfer complete]
3010 [connected]
3011 ## Start Addr = 0x00040004
wdenkc6097192002-11-03 00:24:07 +00003012
wdenk2729af92004-05-03 20:45:30 +00003013 => go 40004
3014 ## Starting application at 0x00040004 ...
3015 TIMERS=0xfff00980
3016 Using timer 1
3017 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
wdenkc6097192002-11-03 00:24:07 +00003018
wdenk2729af92004-05-03 20:45:30 +00003019Hit 'b':
3020 [q, b, e, ?] Set interval 1000000 us
3021 Enabling timer
3022Hit '?':
3023 [q, b, e, ?] ........
3024 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
3025Hit '?':
3026 [q, b, e, ?] .
3027 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
3028Hit '?':
3029 [q, b, e, ?] .
3030 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
3031Hit '?':
3032 [q, b, e, ?] .
3033 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
3034Hit 'e':
3035 [q, b, e, ?] ...Stopping timer
3036Hit 'q':
3037 [q, b, e, ?] ## Application terminated, rc = 0x0
wdenkc6097192002-11-03 00:24:07 +00003038
3039
wdenk2729af92004-05-03 20:45:30 +00003040Minicom warning:
3041================
wdenk85ec0bc2003-03-31 16:34:49 +00003042
wdenk2729af92004-05-03 20:45:30 +00003043Over time, many people have reported problems when trying to use the
3044"minicom" terminal emulation program for serial download. I (wd)
3045consider minicom to be broken, and recommend not to use it. Under
3046Unix, I recommend to use C-Kermit for general purpose use (and
3047especially for kermit binary protocol download ("loadb" command), and
3048use "cu" for S-Record download ("loads" command).
wdenk85ec0bc2003-03-31 16:34:49 +00003049
wdenk2729af92004-05-03 20:45:30 +00003050Nevertheless, if you absolutely want to use it try adding this
3051configuration to your "File transfer protocols" section:
wdenk52f52c12003-06-19 23:04:19 +00003052
wdenk2729af92004-05-03 20:45:30 +00003053 Name Program Name U/D FullScr IO-Red. Multi
3054 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
3055 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
wdenk52f52c12003-06-19 23:04:19 +00003056
3057
wdenk2729af92004-05-03 20:45:30 +00003058NetBSD Notes:
3059=============
wdenkc6097192002-11-03 00:24:07 +00003060
wdenk2729af92004-05-03 20:45:30 +00003061Starting at version 0.9.2, U-Boot supports NetBSD both as host
3062(build U-Boot) and target system (boots NetBSD/mpc8xx).
wdenkc6097192002-11-03 00:24:07 +00003063
wdenk2729af92004-05-03 20:45:30 +00003064Building requires a cross environment; it is known to work on
3065NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
3066need gmake since the Makefiles are not compatible with BSD make).
3067Note that the cross-powerpc package does not install include files;
3068attempting to build U-Boot will fail because <machine/ansi.h> is
3069missing. This file has to be installed and patched manually:
wdenkc6097192002-11-03 00:24:07 +00003070
wdenk2729af92004-05-03 20:45:30 +00003071 # cd /usr/pkg/cross/powerpc-netbsd/include
3072 # mkdir powerpc
3073 # ln -s powerpc machine
3074 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
3075 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
wdenkc6097192002-11-03 00:24:07 +00003076
wdenk2729af92004-05-03 20:45:30 +00003077Native builds *don't* work due to incompatibilities between native
3078and U-Boot include files.
wdenkc6097192002-11-03 00:24:07 +00003079
wdenk2729af92004-05-03 20:45:30 +00003080Booting assumes that (the first part of) the image booted is a
3081stage-2 loader which in turn loads and then invokes the kernel
3082proper. Loader sources will eventually appear in the NetBSD source
3083tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
3084meantime, send mail to bruno@exet-ag.de and/or wd@denx.de for
3085details.
wdenkc6097192002-11-03 00:24:07 +00003086
3087
wdenk2729af92004-05-03 20:45:30 +00003088Implementation Internals:
3089=========================
wdenkc6097192002-11-03 00:24:07 +00003090
wdenk2729af92004-05-03 20:45:30 +00003091The following is not intended to be a complete description of every
3092implementation detail. However, it should help to understand the
3093inner workings of U-Boot and make it easier to port it to custom
3094hardware.
wdenkc6097192002-11-03 00:24:07 +00003095
3096
wdenk2729af92004-05-03 20:45:30 +00003097Initial Stack, Global Data:
3098---------------------------
wdenkc6097192002-11-03 00:24:07 +00003099
wdenk2729af92004-05-03 20:45:30 +00003100The implementation of U-Boot is complicated by the fact that U-Boot
3101starts running out of ROM (flash memory), usually without access to
3102system RAM (because the memory controller is not initialized yet).
3103This means that we don't have writable Data or BSS segments, and BSS
3104is not initialized as zero. To be able to get a C environment working
3105at all, we have to allocate at least a minimal stack. Implementation
3106options for this are defined and restricted by the CPU used: Some CPU
3107models provide on-chip memory (like the IMMR area on MPC8xx and
3108MPC826x processors), on others (parts of) the data cache can be
3109locked as (mis-) used as memory, etc.
wdenkc6097192002-11-03 00:24:07 +00003110
wdenk2729af92004-05-03 20:45:30 +00003111 Chris Hallinan posted a good summary of these issues to the
3112 u-boot-users mailing list:
wdenk43d96162003-03-06 00:02:04 +00003113
wdenk2729af92004-05-03 20:45:30 +00003114 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
3115 From: "Chris Hallinan" <clh@net1plus.com>
3116 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
3117 ...
wdenk43d96162003-03-06 00:02:04 +00003118
wdenk2729af92004-05-03 20:45:30 +00003119 Correct me if I'm wrong, folks, but the way I understand it
3120 is this: Using DCACHE as initial RAM for Stack, etc, does not
3121 require any physical RAM backing up the cache. The cleverness
3122 is that the cache is being used as a temporary supply of
3123 necessary storage before the SDRAM controller is setup. It's
3124 beyond the scope of this list to expain the details, but you
3125 can see how this works by studying the cache architecture and
3126 operation in the architecture and processor-specific manuals.
wdenk43d96162003-03-06 00:02:04 +00003127
wdenk2729af92004-05-03 20:45:30 +00003128 OCM is On Chip Memory, which I believe the 405GP has 4K. It
3129 is another option for the system designer to use as an
3130 initial stack/ram area prior to SDRAM being available. Either
3131 option should work for you. Using CS 4 should be fine if your
3132 board designers haven't used it for something that would
3133 cause you grief during the initial boot! It is frequently not
3134 used.
wdenk43d96162003-03-06 00:02:04 +00003135
wdenk2729af92004-05-03 20:45:30 +00003136 CFG_INIT_RAM_ADDR should be somewhere that won't interfere
3137 with your processor/board/system design. The default value
3138 you will find in any recent u-boot distribution in
3139 Walnut405.h should work for you. I'd set it to a value larger
3140 than your SDRAM module. If you have a 64MB SDRAM module, set
3141 it above 400_0000. Just make sure your board has no resources
3142 that are supposed to respond to that address! That code in
3143 start.S has been around a while and should work as is when
3144 you get the config right.
wdenk43d96162003-03-06 00:02:04 +00003145
wdenk2729af92004-05-03 20:45:30 +00003146 -Chris Hallinan
3147 DS4.COM, Inc.
wdenk43d96162003-03-06 00:02:04 +00003148
wdenk2729af92004-05-03 20:45:30 +00003149It is essential to remember this, since it has some impact on the C
3150code for the initialization procedures:
wdenkc6097192002-11-03 00:24:07 +00003151
wdenk2729af92004-05-03 20:45:30 +00003152* Initialized global data (data segment) is read-only. Do not attempt
3153 to write it.
wdenkc6097192002-11-03 00:24:07 +00003154
wdenk2729af92004-05-03 20:45:30 +00003155* Do not use any unitialized global data (or implicitely initialized
3156 as zero data - BSS segment) at all - this is undefined, initiali-
3157 zation is performed later (when relocating to RAM).
wdenkc6097192002-11-03 00:24:07 +00003158
wdenk2729af92004-05-03 20:45:30 +00003159* Stack space is very limited. Avoid big data buffers or things like
3160 that.
wdenkc6097192002-11-03 00:24:07 +00003161
wdenk2729af92004-05-03 20:45:30 +00003162Having only the stack as writable memory limits means we cannot use
3163normal global data to share information beween the code. But it
3164turned out that the implementation of U-Boot can be greatly
3165simplified by making a global data structure (gd_t) available to all
3166functions. We could pass a pointer to this data as argument to _all_
3167functions, but this would bloat the code. Instead we use a feature of
3168the GCC compiler (Global Register Variables) to share the data: we
3169place a pointer (gd) to the global data into a register which we
3170reserve for this purpose.
wdenkc6097192002-11-03 00:24:07 +00003171
wdenk2729af92004-05-03 20:45:30 +00003172When choosing a register for such a purpose we are restricted by the
3173relevant (E)ABI specifications for the current architecture, and by
3174GCC's implementation.
wdenkc6097192002-11-03 00:24:07 +00003175
wdenk2729af92004-05-03 20:45:30 +00003176For PowerPC, the following registers have specific use:
3177 R1: stack pointer
3178 R2: TOC pointer
3179 R3-R4: parameter passing and return values
3180 R5-R10: parameter passing
3181 R13: small data area pointer
3182 R30: GOT pointer
3183 R31: frame pointer
wdenkc6097192002-11-03 00:24:07 +00003184
wdenk2729af92004-05-03 20:45:30 +00003185 (U-Boot also uses R14 as internal GOT pointer.)
wdenkc6097192002-11-03 00:24:07 +00003186
wdenk2729af92004-05-03 20:45:30 +00003187 ==> U-Boot will use R29 to hold a pointer to the global data
wdenkc6097192002-11-03 00:24:07 +00003188
wdenk2729af92004-05-03 20:45:30 +00003189 Note: on PPC, we could use a static initializer (since the
3190 address of the global data structure is known at compile time),
3191 but it turned out that reserving a register results in somewhat
3192 smaller code - although the code savings are not that big (on
3193 average for all boards 752 bytes for the whole U-Boot image,
3194 624 text + 127 data).
wdenkc6097192002-11-03 00:24:07 +00003195
wdenk2729af92004-05-03 20:45:30 +00003196On ARM, the following registers are used:
wdenkc6097192002-11-03 00:24:07 +00003197
wdenk2729af92004-05-03 20:45:30 +00003198 R0: function argument word/integer result
3199 R1-R3: function argument word
3200 R9: GOT pointer
3201 R10: stack limit (used only if stack checking if enabled)
3202 R11: argument (frame) pointer
3203 R12: temporary workspace
3204 R13: stack pointer
3205 R14: link register
3206 R15: program counter
wdenkc6097192002-11-03 00:24:07 +00003207
wdenk2729af92004-05-03 20:45:30 +00003208 ==> U-Boot will use R8 to hold a pointer to the global data
wdenkc6097192002-11-03 00:24:07 +00003209
3210
wdenk2729af92004-05-03 20:45:30 +00003211Memory Management:
3212------------------
wdenkc6097192002-11-03 00:24:07 +00003213
wdenk2729af92004-05-03 20:45:30 +00003214U-Boot runs in system state and uses physical addresses, i.e. the
3215MMU is not used either for address mapping nor for memory protection.
wdenkc6097192002-11-03 00:24:07 +00003216
wdenk2729af92004-05-03 20:45:30 +00003217The available memory is mapped to fixed addresses using the memory
3218controller. In this process, a contiguous block is formed for each
3219memory type (Flash, SDRAM, SRAM), even when it consists of several
3220physical memory banks.
wdenkc6097192002-11-03 00:24:07 +00003221
wdenk2729af92004-05-03 20:45:30 +00003222U-Boot is installed in the first 128 kB of the first Flash bank (on
3223TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
3224booting and sizing and initializing DRAM, the code relocates itself
3225to the upper end of DRAM. Immediately below the U-Boot code some
3226memory is reserved for use by malloc() [see CFG_MALLOC_LEN
3227configuration setting]. Below that, a structure with global Board
3228Info data is placed, followed by the stack (growing downward).
wdenkc6097192002-11-03 00:24:07 +00003229
wdenk2729af92004-05-03 20:45:30 +00003230Additionally, some exception handler code is copied to the low 8 kB
3231of DRAM (0x00000000 ... 0x00001FFF).
wdenkc6097192002-11-03 00:24:07 +00003232
wdenk2729af92004-05-03 20:45:30 +00003233So a typical memory configuration with 16 MB of DRAM could look like
3234this:
wdenkc6097192002-11-03 00:24:07 +00003235
wdenk2729af92004-05-03 20:45:30 +00003236 0x0000 0000 Exception Vector code
3237 :
3238 0x0000 1FFF
3239 0x0000 2000 Free for Application Use
3240 :
3241 :
wdenkc6097192002-11-03 00:24:07 +00003242
wdenk2729af92004-05-03 20:45:30 +00003243 :
3244 :
3245 0x00FB FF20 Monitor Stack (Growing downward)
3246 0x00FB FFAC Board Info Data and permanent copy of global data
3247 0x00FC 0000 Malloc Arena
3248 :
3249 0x00FD FFFF
3250 0x00FE 0000 RAM Copy of Monitor Code
3251 ... eventually: LCD or video framebuffer
3252 ... eventually: pRAM (Protected RAM - unchanged by reset)
3253 0x00FF FFFF [End of RAM]
wdenkc6097192002-11-03 00:24:07 +00003254
3255
wdenk2729af92004-05-03 20:45:30 +00003256System Initialization:
3257----------------------
wdenkc6097192002-11-03 00:24:07 +00003258
wdenk2729af92004-05-03 20:45:30 +00003259In the reset configuration, U-Boot starts at the reset entry point
3260(on most PowerPC systens at address 0x00000100). Because of the reset
3261configuration for CS0# this is a mirror of the onboard Flash memory.
3262To be able to re-map memory U-Boot then jumps to its link address.
3263To be able to implement the initialization code in C, a (small!)
3264initial stack is set up in the internal Dual Ported RAM (in case CPUs
3265which provide such a feature like MPC8xx or MPC8260), or in a locked
3266part of the data cache. After that, U-Boot initializes the CPU core,
3267the caches and the SIU.
wdenkc6097192002-11-03 00:24:07 +00003268
wdenk2729af92004-05-03 20:45:30 +00003269Next, all (potentially) available memory banks are mapped using a
3270preliminary mapping. For example, we put them on 512 MB boundaries
3271(multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
3272on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
3273programmed for SDRAM access. Using the temporary configuration, a
3274simple memory test is run that determines the size of the SDRAM
3275banks.
wdenkc6097192002-11-03 00:24:07 +00003276
wdenk2729af92004-05-03 20:45:30 +00003277When there is more than one SDRAM bank, and the banks are of
3278different size, the largest is mapped first. For equal size, the first
3279bank (CS2#) is mapped first. The first mapping is always for address
32800x00000000, with any additional banks following immediately to create
3281contiguous memory starting from 0.
wdenkc6097192002-11-03 00:24:07 +00003282
wdenk2729af92004-05-03 20:45:30 +00003283Then, the monitor installs itself at the upper end of the SDRAM area
3284and allocates memory for use by malloc() and for the global Board
3285Info data; also, the exception vector code is copied to the low RAM
3286pages, and the final stack is set up.
wdenkc6097192002-11-03 00:24:07 +00003287
wdenk2729af92004-05-03 20:45:30 +00003288Only after this relocation will you have a "normal" C environment;
3289until that you are restricted in several ways, mostly because you are
3290running from ROM, and because the code will have to be relocated to a
3291new address in RAM.
wdenkc6097192002-11-03 00:24:07 +00003292
3293
wdenk2729af92004-05-03 20:45:30 +00003294U-Boot Porting Guide:
3295----------------------
wdenkc6097192002-11-03 00:24:07 +00003296
wdenk2729af92004-05-03 20:45:30 +00003297[Based on messages by Jerry Van Baren in the U-Boot-Users mailing
3298list, October 2002]
wdenkc6097192002-11-03 00:24:07 +00003299
3300
wdenk2729af92004-05-03 20:45:30 +00003301int main (int argc, char *argv[])
3302{
3303 sighandler_t no_more_time;
wdenkc6097192002-11-03 00:24:07 +00003304
wdenk2729af92004-05-03 20:45:30 +00003305 signal (SIGALRM, no_more_time);
3306 alarm (PROJECT_DEADLINE - toSec (3 * WEEK));
wdenkc6097192002-11-03 00:24:07 +00003307
wdenk2729af92004-05-03 20:45:30 +00003308 if (available_money > available_manpower) {
3309 pay consultant to port U-Boot;
wdenkc6097192002-11-03 00:24:07 +00003310 return 0;
3311 }
3312
wdenk2729af92004-05-03 20:45:30 +00003313 Download latest U-Boot source;
3314
3315 Subscribe to u-boot-users mailing list;
3316
3317 if (clueless) {
3318 email ("Hi, I am new to U-Boot, how do I get started?");
wdenkc6097192002-11-03 00:24:07 +00003319 }
3320
wdenk2729af92004-05-03 20:45:30 +00003321 while (learning) {
3322 Read the README file in the top level directory;
3323 Read http://www.denx.de/twiki/bin/view/DULG/Manual ;
3324 Read the source, Luke;
3325 }
wdenkc6097192002-11-03 00:24:07 +00003326
wdenk2729af92004-05-03 20:45:30 +00003327 if (available_money > toLocalCurrency ($2500)) {
3328 Buy a BDI2000;
3329 } else {
3330 Add a lot of aggravation and time;
3331 }
wdenkc6097192002-11-03 00:24:07 +00003332
wdenk2729af92004-05-03 20:45:30 +00003333 Create your own board support subdirectory;
wdenkc6097192002-11-03 00:24:07 +00003334
wdenk2729af92004-05-03 20:45:30 +00003335 Create your own board config file;
wdenk6aff3112002-12-17 01:51:00 +00003336
wdenk2729af92004-05-03 20:45:30 +00003337 while (!running) {
3338 do {
3339 Add / modify source code;
3340 } until (compiles);
3341 Debug;
3342 if (clueless)
3343 email ("Hi, I am having problems...");
3344 }
3345 Send patch file to Wolfgang;
wdenkc6097192002-11-03 00:24:07 +00003346
wdenk2729af92004-05-03 20:45:30 +00003347 return 0;
3348}
3349
3350void no_more_time (int sig)
3351{
3352 hire_a_guru();
3353}
wdenkc6097192002-11-03 00:24:07 +00003354
3355
wdenk2729af92004-05-03 20:45:30 +00003356Coding Standards:
3357-----------------
wdenkc6097192002-11-03 00:24:07 +00003358
wdenk2729af92004-05-03 20:45:30 +00003359All contributions to U-Boot should conform to the Linux kernel
3360coding style; see the file "Documentation/CodingStyle" in your Linux
3361kernel source directory.
3362
3363Please note that U-Boot is implemented in C (and to some small parts
3364in Assembler); no C++ is used, so please do not use C++ style
3365comments (//) in your code.
3366
3367Please also stick to the following formatting rules:
3368- remove any trailing white space
3369- use TAB characters for indentation, not spaces
3370- make sure NOT to use DOS '\r\n' line feeds
3371- do not add more than 2 empty lines to source files
3372- do not add trailing empty lines to source files
3373
3374Submissions which do not conform to the standards may be returned
3375with a request to reformat the changes.
wdenkc6097192002-11-03 00:24:07 +00003376
3377
wdenk2729af92004-05-03 20:45:30 +00003378Submitting Patches:
3379-------------------
wdenkc6097192002-11-03 00:24:07 +00003380
wdenk2729af92004-05-03 20:45:30 +00003381Since the number of patches for U-Boot is growing, we need to
3382establish some rules. Submissions which do not conform to these rules
3383may be rejected, even when they contain important and valuable stuff.
wdenkc6097192002-11-03 00:24:07 +00003384
3385
wdenk2729af92004-05-03 20:45:30 +00003386When you send a patch, please include the following information with
3387it:
wdenkc6097192002-11-03 00:24:07 +00003388
wdenk2729af92004-05-03 20:45:30 +00003389* For bug fixes: a description of the bug and how your patch fixes
3390 this bug. Please try to include a way of demonstrating that the
3391 patch actually fixes something.
wdenkc6097192002-11-03 00:24:07 +00003392
wdenk2729af92004-05-03 20:45:30 +00003393* For new features: a description of the feature and your
3394 implementation.
wdenkc6097192002-11-03 00:24:07 +00003395
wdenk2729af92004-05-03 20:45:30 +00003396* A CHANGELOG entry as plaintext (separate from the patch)
3397
3398* For major contributions, your entry to the CREDITS file
3399
3400* When you add support for a new board, don't forget to add this
3401 board to the MAKEALL script, too.
3402
3403* If your patch adds new configuration options, don't forget to
3404 document these in the README file.
3405
3406* The patch itself. If you are accessing the CVS repository use "cvs
3407 update; cvs diff -puRN"; else, use "diff -purN OLD NEW". If your
3408 version of diff does not support these options, then get the latest
3409 version of GNU diff.
3410
3411 The current directory when running this command shall be the top
3412 level directory of the U-Boot source tree, or it's parent directory
3413 (i. e. please make sure that your patch includes sufficient
3414 directory information for the affected files).
3415
3416 We accept patches as plain text, MIME attachments or as uuencoded
3417 gzipped text.
3418
3419* If one logical set of modifications affects or creates several
3420 files, all these changes shall be submitted in a SINGLE patch file.
3421
3422* Changesets that contain different, unrelated modifications shall be
3423 submitted as SEPARATE patches, one patch per changeset.
3424
3425
3426Notes:
3427
3428* Before sending the patch, run the MAKEALL script on your patched
3429 source tree and make sure that no errors or warnings are reported
3430 for any of the boards.
3431
3432* Keep your modifications to the necessary minimum: A patch
3433 containing several unrelated changes or arbitrary reformats will be
3434 returned with a request to re-formatting / split it.
3435
3436* If you modify existing code, make sure that your new code does not
3437 add to the memory footprint of the code ;-) Small is beautiful!
3438 When adding new features, these should compile conditionally only
3439 (using #ifdef), and the resulting code with the new feature
3440 disabled must not need more memory than the old code without your
3441 modification.