llvm/docs/CommandGuide/llvm-mca.rst

llvm-mca - LLVM Machine Code Analyzer
=====================================

SYNOPSIS
--------

:program:`llvm-mca` [*options*] [input]

DESCRIPTION
-----------

:program:`llvm-mca` is a performance analysis tool that uses information
available in LLVM (e.g. scheduling models) to statically measure the performance
of machine code in a specific CPU.

Performance is measured in terms of throughput as well as processor resource
consumption. The tool currently works for processors with an out-of-order
backend, for which there is a scheduling model available in LLVM.

The main goal of this tool is not just to predict the performance of the code
when run on the target, but also help with diagnosing potential performance
issues.

Given an assembly code sequence, :program:`llvm-mca` estimates the Instructions
Per Cycle (IPC), as well as hardware resource pressure. The analysis and
reporting style were inspired by the IACA tool from Intel.

For example, you can compile code with clang, output assembly, and pipe it
directly into :program:`llvm-mca` for analysis:

.. code-block:: bash

  $ clang foo.c -O2 -target x86_64-unknown-unknown -S -o - | llvm-mca -mcpu=btver2

Or for Intel syntax:

.. code-block:: bash

  $ clang foo.c -O2 -target x86_64-unknown-unknown -mllvm -x86-asm-syntax=intel -S -o - | llvm-mca -mcpu=btver2

OPTIONS
-------

If ``input`` is "``-``" or omitted, :program:`llvm-mca` reads from standard
input. Otherwise, it will read from the specified filename.

If the :option:`-o` option is omitted, then :program:`llvm-mca` will send its output
to standard output if the input is from standard input.  If the :option:`-o`
option specifies "``-``", then the output will also be sent to standard output.


.. option:: -help

 Print a summary of command line options.

.. option:: -mtriple=<target triple>

 Specify a target triple string.

.. option:: -march=<arch>

 Specify the architecture for which to analyze the code. It defaults to the
 host default target.

.. option:: -mcpu=<cpuname>

  Specify the processor for which to analyze the code.  By default, the cpu name
  is autodetected from the host.

.. option:: -output-asm-variant=<variant id>

 Specify the output assembly variant for the report generated by the tool.
 On x86, possible values are [0, 1]. A value of 0 (vic. 1) for this flag enables
 the AT&T (vic. Intel) assembly format for the code printed out by the tool in
 the analysis report.

.. option:: -dispatch=<width>

 Specify a different dispatch width for the processor. The dispatch width
 defaults to field 'IssueWidth' in the processor scheduling model.  If width is
 zero, then the default dispatch width is used.

.. option:: -register-file-size=<size>

 Specify the size of the register file. When specified, this flag limits how
 many physical registers are available for register renaming purposes. A value
 of zero for this flag means "unlimited number of physical registers".

.. option:: -iterations=<number of iterations>

 Specify the number of iterations to run. If this flag is set to 0, then the
 tool sets the number of iterations to a default value (i.e. 100).

.. option:: -noalias=<bool>

  If set, the tool assumes that loads and stores don't alias. This is the
  default behavior.

.. option:: -lqueue=<load queue size>

  Specify the size of the load queue in the load/store unit emulated by the tool.
  By default, the tool assumes an unbound number of entries in the load queue.
  A value of zero for this flag is ignored, and the default load queue size is
  used instead. 

.. option:: -squeue=<store queue size>

  Specify the size of the store queue in the load/store unit emulated by the
  tool. By default, the tool assumes an unbound number of entries in the store
  queue. A value of zero for this flag is ignored, and the default store queue
  size is used instead.

.. option:: -timeline

  Enable the timeline view.

.. option:: -timeline-max-iterations=<iterations>

  Limit the number of iterations to print in the timeline view. By default, the
  timeline view prints information for up to 10 iterations.

.. option:: -timeline-max-cycles=<cycles>

  Limit the number of cycles in the timeline view. By default, the number of
  cycles is set to 80.

.. option:: -resource-pressure

  Enable the resource pressure view. This is enabled by default.

.. option:: -register-file-stats

  Enable register file usage statistics.

.. option:: -dispatch-stats

  Enable extra dispatch statistics. This view collects and analyzes instruction
  dispatch events, as well as static/dynamic dispatch stall events. This view
  is disabled by default.

.. option:: -scheduler-stats

  Enable extra scheduler statistics. This view collects and analyzes instruction
  issue events. This view is disabled by default.

.. option:: -retire-stats

  Enable extra retire control unit statistics. This view is disabled by default.

.. option:: -instruction-info

  Enable the instruction info view. This is enabled by default.

.. option:: -all-stats

  Print all hardware statistics. This enables extra statistics related to the
  dispatch logic, the hardware schedulers, the register file(s), and the retire
  control unit. This option is disabled by default.

.. option:: -all-views

  Enable all the view.

.. option:: -instruction-tables

  Prints resource pressure information based on the static information
  available from the processor model. This differs from the resource pressure
  view because it doesn't require that the code is simulated. It instead prints
  the theoretical uniform distribution of resource pressure for every
  instruction in sequence.


EXIT STATUS
-----------

:program:`llvm-mca` returns 0 on success. Otherwise, an error message is printed
to standard error, and the tool returns 1.

USING MARKERS TO ANALYZE SPECIFIC CODE BLOCKS
---------------------------------------------
:program:`llvm-mca` allows for the optional usage of special code comments to
mark regions of the assembly code to be analyzed.  A comment starting with
substring ``LLVM-MCA-BEGIN`` marks the beginning of a code region. A comment
starting with substring ``LLVM-MCA-END`` marks the end of a code region.  For
example:

.. code-block:: none

  # LLVM-MCA-BEGIN My Code Region
    ...
  # LLVM-MCA-END

Multiple regions can be specified provided that they do not overlap.  A code
region can have an optional description. If no user-defined region is specified,
then :program:`llvm-mca` assumes a default region which contains every
instruction in the input file.  Every region is analyzed in isolation, and the
final performance report is the union of all the reports generated for every
code region.

Inline assembly directives may be used from source code to annotate the
assembly text:

.. code-block:: c++

  int foo(int a, int b) {
    __asm volatile("# LLVM-MCA-BEGIN foo");
    a += 42;
    __asm volatile("# LLVM-MCA-END");
    a *= b;
    return a;
  }

HOW LLVM-MCA WORKS
------------------

:program:`llvm-mca` takes assembly code as input. The assembly code is parsed
into a sequence of MCInst with the help of the existing LLVM target assembly
parsers. The parsed sequence of MCInst is then analyzed by a ``Pipeline`` module
to generate a performance report.

The Pipeline module simulates the execution of the machine code sequence in a
loop of iterations (default is 100). During this process, the pipeline collects
a number of execution related statistics. At the end of this process, the
pipeline generates and prints a report from the collected statistics.

Here is an example of a performance report generated by the tool for a
dot-product of two packed float vectors of four elements. The analysis is
conducted for target x86, cpu btver2.  The following result can be produced via
the following command using the example located at
``test/tools/llvm-mca/X86/BtVer2/dot-product.s``:

.. code-block:: bash

  $ llvm-mca -mtriple=x86_64-unknown-unknown -mcpu=btver2 -iterations=300 dot-product.s

.. code-block:: none

  Iterations:        300
  Instructions:      900
  Total Cycles:      610
  Total uOps:        900

  Dispatch Width:    2
  uOps Per Cycle:    1.48
  IPC:               1.48
  Block RThroughput: 2.0


  Instruction Info:
  [1]: #uOps
  [2]: Latency
  [3]: RThroughput
  [4]: MayLoad
  [5]: MayStore
  [6]: HasSideEffects (U)

  [1]    [2]    [3]    [4]    [5]    [6]    Instructions:
   1      2     1.00                        vmulps	%xmm0, %xmm1, %xmm2
   1      3     1.00                        vhaddps	%xmm2, %xmm2, %xmm3
   1      3     1.00                        vhaddps	%xmm3, %xmm3, %xmm4


  Resources:
  [0]   - JALU0
  [1]   - JALU1
  [2]   - JDiv
  [3]   - JFPA
  [4]   - JFPM
  [5]   - JFPU0
  [6]   - JFPU1
  [7]   - JLAGU
  [8]   - JMul
  [9]   - JSAGU
  [10]  - JSTC
  [11]  - JVALU0
  [12]  - JVALU1
  [13]  - JVIMUL


  Resource pressure per iteration:
  [0]    [1]    [2]    [3]    [4]    [5]    [6]    [7]    [8]    [9]    [10]   [11]   [12]   [13]
   -      -      -     2.00   1.00   2.00   1.00    -      -      -      -      -      -      -

  Resource pressure by instruction:
  [0]    [1]    [2]    [3]    [4]    [5]    [6]    [7]    [8]    [9]    [10]   [11]   [12]   [13]   Instructions:
   -      -      -      -     1.00    -     1.00    -      -      -      -      -      -      -     vmulps	%xmm0, %xmm1, %xmm2
   -      -      -     1.00    -     1.00    -      -      -      -      -      -      -      -     vhaddps	%xmm2, %xmm2, %xmm3
   -      -      -     1.00    -     1.00    -      -      -      -      -      -      -      -     vhaddps	%xmm3, %xmm3, %xmm4

According to this report, the dot-product kernel has been executed 300 times,
for a total of 900 simulated instructions. The total number of simulated micro
opcodes (uOps) is also 900.

The report is structured in three main sections.  The first section collects a
few performance numbers; the goal of this section is to give a very quick
overview of the performance throughput. Important performance indicators are
**IPC**, **uOps Per Cycle**, and  **Block RThroughput** (Block Reciprocal
Throughput).

IPC is computed dividing the total number of simulated instructions by the total
number of cycles. In the absence of loop-carried data dependencies, the
observed IPC tends to a theoretical maximum which can be computed by dividing
the number of instructions of a single iteration by the *Block RThroughput*.

Field 'uOps Per Cycle' is computed dividing the total number of simulated micro
opcodes by the total number of cycles. A delta between Dispatch Width and this
field is an indicator of a performance issue. In the absence of loop-carried
data dependencies, the observed 'uOps Per Cycle' should tend to a theoretical
maximum throughput which can be computed by dividing the number of uOps of a
single iteration by the *Block RThroughput*.

Field *uOps Per Cycle* is bounded from above by the dispatch width. That is
because the dispatch width limits the maximum size of a dispatch group. Both IPC
and 'uOps Per Cycle' are limited by the amount of hardware parallelism. The
availability of hardware resources affects the resource pressure distribution,
and it limits the number of instructions that can be executed in parallel every
cycle.  A delta between Dispatch Width and the theoretical maximum uOps per
Cycle (computed by dividing the number of uOps of a single iteration by the
*Block RTrhoughput*) is an indicator of a performance bottleneck caused by the
lack of hardware resources.
In general, the lower the Block RThroughput, the better.

In this example, ``uOps per iteration/Block RThroughput`` is 1.50. Since there
are no loop-carried dependencies, the observed *uOps Per Cycle* is expected to
approach 1.50 when the number of iterations tends to infinity. The delta between
the Dispatch Width (2.00), and the theoretical maximum uOp throughput (1.50) is
an indicator of a performance bottleneck caused by the lack of hardware
resources, and the *Resource pressure view* can help to identify the problematic
resource usage.

The second section of the report shows the latency and reciprocal
throughput of every instruction in the sequence. That section also reports
extra information related to the number of micro opcodes, and opcode properties
(i.e., 'MayLoad', 'MayStore', and 'HasSideEffects').

The third section is the *Resource pressure view*.  This view reports
the average number of resource cycles consumed every iteration by instructions
for every processor resource unit available on the target.  Information is
structured in two tables. The first table reports the number of resource cycles
spent on average every iteration. The second table correlates the resource
cycles to the machine instruction in the sequence. For example, every iteration
of the instruction vmulps always executes on resource unit [6]
(JFPU1 - floating point pipeline #1), consuming an average of 1 resource cycle
per iteration.  Note that on AMD Jaguar, vector floating-point multiply can
only be issued to pipeline JFPU1, while horizontal floating-point additions can
only be issued to pipeline JFPU0.

The resource pressure view helps with identifying bottlenecks caused by high
usage of specific hardware resources.  Situations with resource pressure mainly
concentrated on a few resources should, in general, be avoided.  Ideally,
pressure should be uniformly distributed between multiple resources.

Timeline View
^^^^^^^^^^^^^
The timeline view produces a detailed report of each instruction's state
transitions through an instruction pipeline.  This view is enabled by the
command line option ``-timeline``.  As instructions transition through the
various stages of the pipeline, their states are depicted in the view report.
These states are represented by the following characters:

* D : Instruction dispatched.
* e : Instruction executing.
* E : Instruction executed.
* R : Instruction retired.
* = : Instruction already dispatched, waiting to be executed.
* \- : Instruction executed, waiting to be retired.

Below is the timeline view for a subset of the dot-product example located in
``test/tools/llvm-mca/X86/BtVer2/dot-product.s`` and processed by
:program:`llvm-mca` using the following command:

.. code-block:: bash

  $ llvm-mca -mtriple=x86_64-unknown-unknown -mcpu=btver2 -iterations=3 -timeline dot-product.s

.. code-block:: none

  Timeline view:
                      012345
  Index     0123456789

  [0,0]     DeeER.    .    .   vmulps	%xmm0, %xmm1, %xmm2
  [0,1]     D==eeeER  .    .   vhaddps	%xmm2, %xmm2, %xmm3
  [0,2]     .D====eeeER    .   vhaddps	%xmm3, %xmm3, %xmm4
  [1,0]     .DeeE-----R    .   vmulps	%xmm0, %xmm1, %xmm2
  [1,1]     . D=eeeE---R   .   vhaddps	%xmm2, %xmm2, %xmm3
  [1,2]     . D====eeeER   .   vhaddps	%xmm3, %xmm3, %xmm4
  [2,0]     .  DeeE-----R  .   vmulps	%xmm0, %xmm1, %xmm2
  [2,1]     .  D====eeeER  .   vhaddps	%xmm2, %xmm2, %xmm3
  [2,2]     .   D======eeeER   vhaddps	%xmm3, %xmm3, %xmm4


  Average Wait times (based on the timeline view):
  [0]: Executions
  [1]: Average time spent waiting in a scheduler's queue
  [2]: Average time spent waiting in a scheduler's queue while ready
  [3]: Average time elapsed from WB until retire stage

        [0]    [1]    [2]    [3]
  0.     3     1.0    1.0    3.3       vmulps	%xmm0, %xmm1, %xmm2
  1.     3     3.3    0.7    1.0       vhaddps	%xmm2, %xmm2, %xmm3
  2.     3     5.7    0.0    0.0       vhaddps	%xmm3, %xmm3, %xmm4

The timeline view is interesting because it shows instruction state changes
during execution.  It also gives an idea of how the tool processes instructions
executed on the target, and how their timing information might be calculated.

The timeline view is structured in two tables.  The first table shows
instructions changing state over time (measured in cycles); the second table
(named *Average Wait times*) reports useful timing statistics, which should
help diagnose performance bottlenecks caused by long data dependencies and
sub-optimal usage of hardware resources.

An instruction in the timeline view is identified by a pair of indices, where
the first index identifies an iteration, and the second index is the
instruction index (i.e., where it appears in the code sequence).  Since this
example was generated using 3 iterations: ``-iterations=3``, the iteration
indices range from 0-2 inclusively.

Excluding the first and last column, the remaining columns are in cycles.
Cycles are numbered sequentially starting from 0.

From the example output above, we know the following:

* Instruction [1,0] was dispatched at cycle 1.
* Instruction [1,0] started executing at cycle 2.
* Instruction [1,0] reached the write back stage at cycle 4.
* Instruction [1,0] was retired at cycle 10.

Instruction [1,0] (i.e., vmulps from iteration #1) does not have to wait in the
scheduler's queue for the operands to become available. By the time vmulps is
dispatched, operands are already available, and pipeline JFPU1 is ready to
serve another instruction.  So the instruction can be immediately issued on the
JFPU1 pipeline. That is demonstrated by the fact that the instruction only
spent 1cy in the scheduler's queue.

There is a gap of 5 cycles between the write-back stage and the retire event.
That is because instructions must retire in program order, so [1,0] has to wait
for [0,2] to be retired first (i.e., it has to wait until cycle 10).

In the example, all instructions are in a RAW (Read After Write) dependency
chain.  Register %xmm2 written by vmulps is immediately used by the first
vhaddps, and register %xmm3 written by the first vhaddps is used by the second
vhaddps.  Long data dependencies negatively impact the ILP (Instruction Level
Parallelism).

In the dot-product example, there are anti-dependencies introduced by
instructions from different iterations.  However, those dependencies can be
removed at register renaming stage (at the cost of allocating register aliases,
and therefore consuming physical registers).

Table *Average Wait times* helps diagnose performance issues that are caused by
the presence of long latency instructions and potentially long data dependencies
which may limit the ILP.  Note that :program:`llvm-mca`, by default, assumes at
least 1cy between the dispatch event and the issue event.

When the performance is limited by data dependencies and/or long latency
instructions, the number of cycles spent while in the *ready* state is expected
to be very small when compared with the total number of cycles spent in the
scheduler's queue.  The difference between the two counters is a good indicator
of how large of an impact data dependencies had on the execution of the
instructions.  When performance is mostly limited by the lack of hardware
resources, the delta between the two counters is small.  However, the number of
cycles spent in the queue tends to be larger (i.e., more than 1-3cy),
especially when compared to other low latency instructions.

Extra Statistics to Further Diagnose Performance Issues
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The ``-all-stats`` command line option enables extra statistics and performance
counters for the dispatch logic, the reorder buffer, the retire control unit,
and the register file.

Below is an example of ``-all-stats`` output generated by  :program:`llvm-mca`
for 300 iterations of the dot-product example discussed in the previous
sections.

.. code-block:: none

  Dynamic Dispatch Stall Cycles:
  RAT     - Register unavailable:                      0
  RCU     - Retire tokens unavailable:                 0
  SCHEDQ  - Scheduler full:                            272
  LQ      - Load queue full:                           0
  SQ      - Store queue full:                          0
  GROUP   - Static restrictions on the dispatch group: 0


  Dispatch Logic - number of cycles where we saw N instructions dispatched:
  [# dispatched], [# cycles]
   0,              24  (3.9%)
   1,              272  (44.6%)
   2,              314  (51.5%)


  Schedulers - number of cycles where we saw N instructions issued:
  [# issued], [# cycles]
   0,          7  (1.1%)
   1,          306  (50.2%)
   2,          297  (48.7%)

  Scheduler's queue usage:
  [1] Resource name.
  [2] Average number of used buffer entries.
  [3] Maximum number of used buffer entries.
  [4] Total number of buffer entries.

   [1]            [2]        [3]        [4]
  JALU01           0          0          20
  JFPU01           17         18         18
  JLSAGU           0          0          12


  Retire Control Unit - number of cycles where we saw N instructions retired:
  [# retired], [# cycles]
   0,           109  (17.9%)
   1,           102  (16.7%)
   2,           399  (65.4%)


  Register File statistics:
  Total number of mappings created:    900
  Max number of mappings used:         35

  *  Register File #1 -- JFpuPRF:
     Number of physical registers:     72
     Total number of mappings created: 900
     Max number of mappings used:      35

  *  Register File #2 -- JIntegerPRF:
     Number of physical registers:     64
     Total number of mappings created: 0
     Max number of mappings used:      0

If we look at the *Dynamic Dispatch Stall Cycles* table, we see the counter for
SCHEDQ reports 272 cycles.  This counter is incremented every time the dispatch
logic is unable to dispatch a group of two instructions because the scheduler's
queue is full.

Looking at the *Dispatch Logic* table, we see that the pipeline was only able to
dispatch two instructions 51.5% of the time.  The dispatch group was limited to
one instruction 44.6% of the cycles, which corresponds to 272 cycles.  The
dispatch statistics are displayed by either using the command option
``-all-stats`` or ``-dispatch-stats``.

The next table, *Schedulers*, presents a histogram displaying a count,
representing the number of instructions issued on some number of cycles.  In
this case, of the 610 simulated cycles, single instructions were issued 306
times (50.2%) and there were 7 cycles where no instructions were issued.

The *Scheduler's queue usage* table shows that the average and maximum number of
buffer entries (i.e., scheduler queue entries) used at runtime.  Resource JFPU01
reached its maximum (18 of 18 queue entries). Note that AMD Jaguar implements
three schedulers:

* JALU01 - A scheduler for ALU instructions.
* JFPU01 - A scheduler floating point operations.
* JLSAGU - A scheduler for address generation.

The dot-product is a kernel of three floating point instructions (a vector
multiply followed by two horizontal adds).  That explains why only the floating
point scheduler appears to be used.

A full scheduler queue is either caused by data dependency chains or by a
sub-optimal usage of hardware resources.  Sometimes, resource pressure can be
mitigated by rewriting the kernel using different instructions that consume
different scheduler resources.  Schedulers with a small queue are less resilient
to bottlenecks caused by the presence of long data dependencies.  The scheduler
statistics are displayed by using the command option ``-all-stats`` or
``-scheduler-stats``.

The next table, *Retire Control Unit*, presents a histogram displaying a count,
representing the number of instructions retired on some number of cycles.  In
this case, of the 610 simulated cycles, two instructions were retired during the
same cycle 399 times (65.4%) and there were 109 cycles where no instructions
were retired.  The retire statistics are displayed by using the command option
``-all-stats`` or ``-retire-stats``.

The last table presented is *Register File statistics*.  Each physical register
file (PRF) used by the pipeline is presented in this table.  In the case of AMD
Jaguar, there are two register files, one for floating-point registers (JFpuPRF)
and one for integer registers (JIntegerPRF).  The table shows that of the 900
instructions processed, there were 900 mappings created.  Since this dot-product
example utilized only floating point registers, the JFPuPRF was responsible for
creating the 900 mappings.  However, we see that the pipeline only used a
maximum of 35 of 72 available register slots at any given time. We can conclude
that the floating point PRF was the only register file used for the example, and
that it was never resource constrained.  The register file statistics are
displayed by using the command option ``-all-stats`` or
``-register-file-stats``.

In this example, we can conclude that the IPC is mostly limited by data
dependencies, and not by resource pressure.

Instruction Flow
^^^^^^^^^^^^^^^^
This section describes the instruction flow through the default pipeline of
:program:`llvm-mca`, as well as the functional units involved in the process.

The default pipeline implements the following sequence of stages used to
process instructions.

* Dispatch (Instruction is dispatched to the schedulers).
* Issue (Instruction is issued to the processor pipelines).
* Write Back (Instruction is executed, and results are written back).
* Retire (Instruction is retired; writes are architecturally committed).

The default pipeline only models the out-of-order portion of a processor.
Therefore, the instruction fetch and decode stages are not modeled. Performance
bottlenecks in the frontend are not diagnosed. :program:`llvm-mca` assumes that
instructions have all been decoded and placed into a queue before the simulation
start.  Also, :program:`llvm-mca` does not model branch prediction.

Instruction Dispatch
""""""""""""""""""""
During the dispatch stage, instructions are picked in program order from a
queue of already decoded instructions, and dispatched in groups to the
simulated hardware schedulers.

The size of a dispatch group depends on the availability of the simulated
hardware resources.  The processor dispatch width defaults to the value
of the ``IssueWidth`` in LLVM's scheduling model.

An instruction can be dispatched if:

* The size of the dispatch group is smaller than processor's dispatch width.
* There are enough entries in the reorder buffer.
* There are enough physical registers to do register renaming.
* The schedulers are not full.

Scheduling models can optionally specify which register files are available on
the processor. :program:`llvm-mca` uses that information to initialize register
file descriptors.  Users can limit the number of physical registers that are
globally available for register renaming by using the command option
``-register-file-size``.  A value of zero for this option means *unbounded*. By
knowing how many registers are available for renaming, the tool can predict
dispatch stalls caused by the lack of physical registers.

The number of reorder buffer entries consumed by an instruction depends on the
number of micro-opcodes specified for that instruction by the target scheduling
model.  The reorder buffer is responsible for tracking the progress of
instructions that are "in-flight", and retiring them in program order.  The
number of entries in the reorder buffer defaults to the value specified by field
`MicroOpBufferSize` in the target scheduling model.

Instructions that are dispatched to the schedulers consume scheduler buffer
entries. :program:`llvm-mca` queries the scheduling model to determine the set
of buffered resources consumed by an instruction.  Buffered resources are
treated like scheduler resources.

Instruction Issue
"""""""""""""""""
Each processor scheduler implements a buffer of instructions.  An instruction
has to wait in the scheduler's buffer until input register operands become
available.  Only at that point, does the instruction becomes eligible for
execution and may be issued (potentially out-of-order) for execution.
Instruction latencies are computed by :program:`llvm-mca` with the help of the
scheduling model.

:program:`llvm-mca`'s scheduler is designed to simulate multiple processor
schedulers.  The scheduler is responsible for tracking data dependencies, and
dynamically selecting which processor resources are consumed by instructions.
It delegates the management of processor resource units and resource groups to a
resource manager.  The resource manager is responsible for selecting resource
units that are consumed by instructions.  For example, if an instruction
consumes 1cy of a resource group, the resource manager selects one of the
available units from the group; by default, the resource manager uses a
round-robin selector to guarantee that resource usage is uniformly distributed
between all units of a group.

:program:`llvm-mca`'s scheduler internally groups instructions into three sets:

* WaitSet: a set of instructions whose operands are not ready.
* ReadySet: a set of instructions ready to execute.
* IssuedSet: a set of instructions executing.

Depending on the operands availability, instructions that are dispatched to the
scheduler are either placed into the WaitSet or into the ReadySet.

Every cycle, the scheduler checks if instructions can be moved from the WaitSet
to the ReadySet, and if instructions from the ReadySet can be issued to the
underlying pipelines. The algorithm prioritizes older instructions over younger
instructions.

Write-Back and Retire Stage
"""""""""""""""""""""""""""
Issued instructions are moved from the ReadySet to the IssuedSet.  There,
instructions wait until they reach the write-back stage.  At that point, they
get removed from the queue and the retire control unit is notified.

When instructions are executed, the retire control unit flags the instruction as
"ready to retire."

Instructions are retired in program order.  The register file is notified of the
retirement so that it can free the physical registers that were allocated for
the instruction during the register renaming stage.

Load/Store Unit and Memory Consistency Model
""""""""""""""""""""""""""""""""""""""""""""
To simulate an out-of-order execution of memory operations, :program:`llvm-mca`
utilizes a simulated load/store unit (LSUnit) to simulate the speculative
execution of loads and stores.

Each load (or store) consumes an entry in the load (or store) queue. Users can
specify flags ``-lqueue`` and ``-squeue`` to limit the number of entries in the
load and store queues respectively. The queues are unbounded by default.

The LSUnit implements a relaxed consistency model for memory loads and stores.
The rules are:

1. A younger load is allowed to pass an older load only if there are no
   intervening stores or barriers between the two loads.
2. A younger load is allowed to pass an older store provided that the load does
   not alias with the store.
3. A younger store is not allowed to pass an older store.
4. A younger store is not allowed to pass an older load.

By default, the LSUnit optimistically assumes that loads do not alias
(`-noalias=true`) store operations.  Under this assumption, younger loads are
always allowed to pass older stores.  Essentially, the LSUnit does not attempt
to run any alias analysis to predict when loads and stores do not alias with
each other.

Note that, in the case of write-combining memory, rule 3 could be relaxed to
allow reordering of non-aliasing store operations.  That being said, at the
moment, there is no way to further relax the memory model (``-noalias`` is the
only option).  Essentially, there is no option to specify a different memory
type (e.g., write-back, write-combining, write-through; etc.) and consequently
to weaken, or strengthen, the memory model.

Other limitations are:

* The LSUnit does not know when store-to-load forwarding may occur.
* The LSUnit does not know anything about cache hierarchy and memory types.
* The LSUnit does not know how to identify serializing operations and memory
  fences.

The LSUnit does not attempt to predict if a load or store hits or misses the L1
cache.  It only knows if an instruction "MayLoad" and/or "MayStore."  For
loads, the scheduling model provides an "optimistic" load-to-use latency (which
usually matches the load-to-use latency for when there is a hit in the L1D).

:program:`llvm-mca` does not know about serializing operations or memory-barrier
like instructions.  The LSUnit conservatively assumes that an instruction which
has both "MayLoad" and unmodeled side effects behaves like a "soft"
load-barrier.  That means, it serializes loads without forcing a flush of the
load queue.  Similarly, instructions that "MayStore" and have unmodeled side
effects are treated like store barriers.  A full memory barrier is a "MayLoad"
and "MayStore" instruction with unmodeled side effects.  This is inaccurate, but
it is the best that we can do at the moment with the current information
available in LLVM.

A load/store barrier consumes one entry of the load/store queue.  A load/store
barrier enforces ordering of loads/stores.  A younger load cannot pass a load
barrier.  Also, a younger store cannot pass a store barrier.  A younger load
has to wait for the memory/load barrier to execute.  A load/store barrier is
"executed" when it becomes the oldest entry in the load/store queue(s). That
also means, by construction, all of the older loads/stores have been executed.

In conclusion, the full set of load/store consistency rules are:

#. A store may not pass a previous store.
#. A store may not pass a previous load (regardless of ``-noalias``).
#. A store has to wait until an older store barrier is fully executed.
#. A load may pass a previous load.
#. A load may not pass a previous store unless ``-noalias`` is set.
#. A load has to wait until an older load barrier is fully executed.