blob: 79016e690ace8899488e54ee7a35e1715018e9a2 [file] [log] [blame]
wdenkc6097192002-11-03 00:24:07 +00001#
Wolfgang Denkb75190d2012-01-19 10:58:21 +01002# (C) Copyright 2000 - 2012
wdenkc6097192002-11-03 00:24:07 +00003# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
4#
5# See file CREDITS for list of people who contributed to this
6# project.
7#
8# This program is free software; you can redistribute it and/or
9# modify it under the terms of the GNU General Public License as
10# published by the Free Software Foundation; either version 2 of
11# the License, or (at your option) any later version.
12#
13# This program is distributed in the hope that it will be useful,
14# but WITHOUT ANY WARRANTY; without even the implied warranty of
15# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16# GNU General Public License for more details.
17#
18# You should have received a copy of the GNU General Public License
19# along with this program; if not, write to the Free Software
20# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
21# MA 02111-1307 USA
22#
23
24Summary:
25========
26
wdenk24ee89b2002-11-03 17:56:27 +000027This directory contains the source code for U-Boot, a boot loader for
wdenke86e5a02004-10-17 21:12:06 +000028Embedded boards based on PowerPC, ARM, MIPS and several other
29processors, which can be installed in a boot ROM and used to
30initialize and test the hardware or to download and run application
31code.
wdenkc6097192002-11-03 00:24:07 +000032
33The development of U-Boot is closely related to Linux: some parts of
wdenk24ee89b2002-11-03 17:56:27 +000034the source code originate in the Linux source tree, we have some
35header files in common, and special provision has been made to
wdenkc6097192002-11-03 00:24:07 +000036support booting of Linux images.
37
38Some attention has been paid to make this software easily
39configurable and extendable. For instance, all monitor commands are
40implemented with the same call interface, so that it's very easy to
41add new commands. Also, instead of permanently adding rarely used
42code (for instance hardware test utilities) to the monitor, you can
43load and run it dynamically.
44
45
46Status:
47=======
48
49In general, all boards for which a configuration option exists in the
wdenk24ee89b2002-11-03 17:56:27 +000050Makefile have been tested to some extent and can be considered
wdenkc6097192002-11-03 00:24:07 +000051"working". In fact, many of them are used in production systems.
52
wdenk24ee89b2002-11-03 17:56:27 +000053In case of problems see the CHANGELOG and CREDITS files to find out
Wolfgang Denk218ca722008-03-26 10:40:12 +010054who contributed the specific port. The MAINTAINERS file lists board
55maintainers.
wdenkc6097192002-11-03 00:24:07 +000056
wdenkc6097192002-11-03 00:24:07 +000057
58Where to get help:
59==================
60
wdenk24ee89b2002-11-03 17:56:27 +000061In case you have questions about, problems with or contributions for
62U-Boot you should send a message to the U-Boot mailing list at
Peter Tyser0c325652008-09-10 09:18:34 -050063<u-boot@lists.denx.de>. There is also an archive of previous traffic
64on the mailing list - please search the archive before asking FAQ's.
65Please see http://lists.denx.de/pipermail/u-boot and
66http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
wdenkc6097192002-11-03 00:24:07 +000067
68
Wolfgang Denk218ca722008-03-26 10:40:12 +010069Where to get source code:
70=========================
71
72The U-Boot source code is maintained in the git repository at
73git://www.denx.de/git/u-boot.git ; you can browse it online at
74http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
75
76The "snapshot" links on this page allow you to download tarballs of
Marcel Ziswiler11ccc332008-07-09 08:17:15 +020077any version you might be interested in. Official releases are also
Wolfgang Denk218ca722008-03-26 10:40:12 +010078available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
79directory.
80
Anatolij Gustschind4ee7112008-03-26 18:13:33 +010081Pre-built (and tested) images are available from
Wolfgang Denk218ca722008-03-26 10:40:12 +010082ftp://ftp.denx.de/pub/u-boot/images/
83
84
wdenkc6097192002-11-03 00:24:07 +000085Where we come from:
86===================
87
88- start from 8xxrom sources
wdenk24ee89b2002-11-03 17:56:27 +000089- create PPCBoot project (http://sourceforge.net/projects/ppcboot)
wdenkc6097192002-11-03 00:24:07 +000090- clean up code
91- make it easier to add custom boards
92- make it possible to add other [PowerPC] CPUs
93- extend functions, especially:
94 * Provide extended interface to Linux boot loader
95 * S-Record download
96 * network boot
Marcel Ziswiler11ccc332008-07-09 08:17:15 +020097 * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
wdenk24ee89b2002-11-03 17:56:27 +000098- create ARMBoot project (http://sourceforge.net/projects/armboot)
wdenkc6097192002-11-03 00:24:07 +000099- add other CPU families (starting with ARM)
wdenk24ee89b2002-11-03 17:56:27 +0000100- create U-Boot project (http://sourceforge.net/projects/u-boot)
Magnus Lilja0d28f342008-08-06 19:32:33 +0200101- current project page: see http://www.denx.de/wiki/U-Boot
wdenk24ee89b2002-11-03 17:56:27 +0000102
103
104Names and Spelling:
105===================
106
107The "official" name of this project is "Das U-Boot". The spelling
108"U-Boot" shall be used in all written text (documentation, comments
109in source files etc.). Example:
110
111 This is the README file for the U-Boot project.
112
113File names etc. shall be based on the string "u-boot". Examples:
114
115 include/asm-ppc/u-boot.h
116
117 #include <asm/u-boot.h>
118
119Variable names, preprocessor constants etc. shall be either based on
120the string "u_boot" or on "U_BOOT". Example:
121
122 U_BOOT_VERSION u_boot_logo
123 IH_OS_U_BOOT u_boot_hush_start
wdenkc6097192002-11-03 00:24:07 +0000124
125
wdenk93f19cc2002-12-17 17:55:09 +0000126Versioning:
127===========
128
Thomas Weber360d8832010-09-28 08:06:25 +0200129Starting with the release in October 2008, the names of the releases
130were changed from numerical release numbers without deeper meaning
131into a time stamp based numbering. Regular releases are identified by
132names consisting of the calendar year and month of the release date.
133Additional fields (if present) indicate release candidates or bug fix
134releases in "stable" maintenance trees.
wdenk93f19cc2002-12-17 17:55:09 +0000135
Thomas Weber360d8832010-09-28 08:06:25 +0200136Examples:
Wolfgang Denkc0f40852011-10-26 10:21:21 +0000137 U-Boot v2009.11 - Release November 2009
Thomas Weber360d8832010-09-28 08:06:25 +0200138 U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree
139 U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
wdenk93f19cc2002-12-17 17:55:09 +0000140
141
wdenkc6097192002-11-03 00:24:07 +0000142Directory Hierarchy:
143====================
144
Peter Tyser8d321b82010-04-12 22:28:21 -0500145/arch Architecture specific files
146 /arm Files generic to ARM architecture
147 /cpu CPU specific files
148 /arm720t Files specific to ARM 720 CPUs
149 /arm920t Files specific to ARM 920 CPUs
Andreas Bießmann6eb09212011-07-18 09:41:08 +0000150 /at91 Files specific to Atmel AT91RM9200 CPU
Wolfgang Denka9046b92010-06-13 17:48:15 +0200151 /imx Files specific to Freescale MC9328 i.MX CPUs
152 /s3c24x0 Files specific to Samsung S3C24X0 CPUs
Peter Tyser8d321b82010-04-12 22:28:21 -0500153 /arm925t Files specific to ARM 925 CPUs
154 /arm926ejs Files specific to ARM 926 CPUs
155 /arm1136 Files specific to ARM 1136 CPUs
156 /ixp Files specific to Intel XScale IXP CPUs
157 /pxa Files specific to Intel XScale PXA CPUs
158 /s3c44b0 Files specific to Samsung S3C44B0 CPUs
159 /sa1100 Files specific to Intel StrongARM SA1100 CPUs
160 /lib Architecture specific library files
161 /avr32 Files generic to AVR32 architecture
162 /cpu CPU specific files
163 /lib Architecture specific library files
164 /blackfin Files generic to Analog Devices Blackfin architecture
165 /cpu CPU specific files
166 /lib Architecture specific library files
Graeme Russfea25722011-04-13 19:43:28 +1000167 /x86 Files generic to x86 architecture
Peter Tyser8d321b82010-04-12 22:28:21 -0500168 /cpu CPU specific files
169 /lib Architecture specific library files
170 /m68k Files generic to m68k architecture
171 /cpu CPU specific files
172 /mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
173 /mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
174 /mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
175 /mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
176 /mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
177 /lib Architecture specific library files
178 /microblaze Files generic to microblaze architecture
179 /cpu CPU specific files
180 /lib Architecture specific library files
181 /mips Files generic to MIPS architecture
182 /cpu CPU specific files
Daniel Schwierzeck92bbd642011-07-27 13:22:39 +0200183 /mips32 Files specific to MIPS32 CPUs
Xiangfu Liu80421fc2011-10-12 12:24:06 +0800184 /xburst Files specific to Ingenic XBurst CPUs
Peter Tyser8d321b82010-04-12 22:28:21 -0500185 /lib Architecture specific library files
Macpaul Linafc1ce82011-10-19 20:41:11 +0000186 /nds32 Files generic to NDS32 architecture
187 /cpu CPU specific files
188 /n1213 Files specific to Andes Technology N1213 CPUs
189 /lib Architecture specific library files
Peter Tyser8d321b82010-04-12 22:28:21 -0500190 /nios2 Files generic to Altera NIOS2 architecture
191 /cpu CPU specific files
192 /lib Architecture specific library files
Stefan Roesea47a12b2010-04-15 16:07:28 +0200193 /powerpc Files generic to PowerPC architecture
Peter Tyser8d321b82010-04-12 22:28:21 -0500194 /cpu CPU specific files
195 /74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
196 /mpc5xx Files specific to Freescale MPC5xx CPUs
197 /mpc5xxx Files specific to Freescale MPC5xxx CPUs
198 /mpc8xx Files specific to Freescale MPC8xx CPUs
199 /mpc8220 Files specific to Freescale MPC8220 CPUs
200 /mpc824x Files specific to Freescale MPC824x CPUs
201 /mpc8260 Files specific to Freescale MPC8260 CPUs
202 /mpc85xx Files specific to Freescale MPC85xx CPUs
203 /ppc4xx Files specific to AMCC PowerPC 4xx CPUs
204 /lib Architecture specific library files
205 /sh Files generic to SH architecture
206 /cpu CPU specific files
207 /sh2 Files specific to sh2 CPUs
208 /sh3 Files specific to sh3 CPUs
209 /sh4 Files specific to sh4 CPUs
210 /lib Architecture specific library files
211 /sparc Files generic to SPARC architecture
212 /cpu CPU specific files
213 /leon2 Files specific to Gaisler LEON2 SPARC CPU
214 /leon3 Files specific to Gaisler LEON3 SPARC CPU
215 /lib Architecture specific library files
216/api Machine/arch independent API for external apps
217/board Board dependent files
218/common Misc architecture independent functions
219/disk Code for disk drive partition handling
220/doc Documentation (don't expect too much)
221/drivers Commonly used device drivers
222/examples Example code for standalone applications, etc.
223/fs Filesystem code (cramfs, ext2, jffs2, etc.)
224/include Header Files
225/lib Files generic to all architectures
226 /libfdt Library files to support flattened device trees
227 /lzma Library files to support LZMA decompression
228 /lzo Library files to support LZO decompression
229/net Networking code
230/post Power On Self Test
231/rtc Real Time Clock drivers
232/tools Tools to build S-Record or U-Boot images, etc.
wdenkc6097192002-11-03 00:24:07 +0000233
wdenkc6097192002-11-03 00:24:07 +0000234Software Configuration:
235=======================
236
237Configuration is usually done using C preprocessor defines; the
238rationale behind that is to avoid dead code whenever possible.
239
240There are two classes of configuration variables:
241
242* Configuration _OPTIONS_:
243 These are selectable by the user and have names beginning with
244 "CONFIG_".
245
246* Configuration _SETTINGS_:
247 These depend on the hardware etc. and should not be meddled with if
248 you don't know what you're doing; they have names beginning with
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200249 "CONFIG_SYS_".
wdenkc6097192002-11-03 00:24:07 +0000250
251Later we will add a configuration tool - probably similar to or even
252identical to what's used for the Linux kernel. Right now, we have to
253do the configuration by hand, which means creating some symbolic
254links and editing some configuration files. We use the TQM8xxL boards
255as an example here.
256
257
258Selection of Processor Architecture and Board Type:
259---------------------------------------------------
260
261For all supported boards there are ready-to-use default
262configurations available; just type "make <board_name>_config".
263
264Example: For a TQM823L module type:
265
266 cd u-boot
267 make TQM823L_config
268
Marcel Ziswiler11ccc332008-07-09 08:17:15 +0200269For the Cogent platform, you need to specify the CPU type as well;
wdenkc6097192002-11-03 00:24:07 +0000270e.g. "make cogent_mpc8xx_config". And also configure the cogent
271directory according to the instructions in cogent/README.
272
273
274Configuration Options:
275----------------------
276
277Configuration depends on the combination of board and CPU type; all
278such information is kept in a configuration file
279"include/configs/<board_name>.h".
280
281Example: For a TQM823L module, all configuration settings are in
282"include/configs/TQM823L.h".
283
284
wdenk7f6c2cb2002-11-10 22:06:23 +0000285Many of the options are named exactly as the corresponding Linux
286kernel configuration options. The intention is to make it easier to
287build a config tool - later.
288
289
wdenkc6097192002-11-03 00:24:07 +0000290The following options need to be configured:
291
Kim Phillips26281142007-08-10 13:28:25 -0500292- CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
wdenkc6097192002-11-03 00:24:07 +0000293
Kim Phillips26281142007-08-10 13:28:25 -0500294- Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
Wolfgang Denk6ccec442006-10-24 14:42:37 +0200295
296- CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
Haavard Skinnemoen09ea0de2007-11-01 12:44:20 +0100297 Define exactly one, e.g. CONFIG_ATSTK1002
wdenkc6097192002-11-03 00:24:07 +0000298
299- CPU Module Type: (if CONFIG_COGENT is defined)
300 Define exactly one of
301 CONFIG_CMA286_60_OLD
302--- FIXME --- not tested yet:
303 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
304 CONFIG_CMA287_23, CONFIG_CMA287_50
305
306- Motherboard Type: (if CONFIG_COGENT is defined)
307 Define exactly one of
308 CONFIG_CMA101, CONFIG_CMA102
309
310- Motherboard I/O Modules: (if CONFIG_COGENT is defined)
311 Define one or more of
312 CONFIG_CMA302
313
314- Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
315 Define one or more of
316 CONFIG_LCD_HEARTBEAT - update a character position on
Marcel Ziswiler11ccc332008-07-09 08:17:15 +0200317 the LCD display every second with
wdenkc6097192002-11-03 00:24:07 +0000318 a "rotator" |\-/|\-/
319
wdenk2535d602003-07-17 23:16:40 +0000320- Board flavour: (if CONFIG_MPC8260ADS is defined)
321 CONFIG_ADSTYPE
322 Possible values are:
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200323 CONFIG_SYS_8260ADS - original MPC8260ADS
324 CONFIG_SYS_8266ADS - MPC8266ADS
325 CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
326 CONFIG_SYS_8272ADS - MPC8272ADS
wdenk2535d602003-07-17 23:16:40 +0000327
Lei Wencf946c62011-02-09 18:06:58 +0530328- Marvell Family Member
329 CONFIG_SYS_MVFS - define it if you want to enable
330 multiple fs option at one time
331 for marvell soc family
332
wdenkc6097192002-11-03 00:24:07 +0000333- MPC824X Family Member (if CONFIG_MPC824X is defined)
wdenk5da627a2003-10-09 20:09:04 +0000334 Define exactly one of
335 CONFIG_MPC8240, CONFIG_MPC8245
wdenkc6097192002-11-03 00:24:07 +0000336
Marcel Ziswiler11ccc332008-07-09 08:17:15 +0200337- 8xx CPU Options: (if using an MPC8xx CPU)
wdenk66ca92a2004-09-28 17:59:53 +0000338 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
339 get_gclk_freq() cannot work
wdenk5da627a2003-10-09 20:09:04 +0000340 e.g. if there is no 32KHz
341 reference PIT/RTC clock
wdenk66ca92a2004-09-28 17:59:53 +0000342 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
343 or XTAL/EXTAL)
wdenkc6097192002-11-03 00:24:07 +0000344
wdenk66ca92a2004-09-28 17:59:53 +0000345- 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200346 CONFIG_SYS_8xx_CPUCLK_MIN
347 CONFIG_SYS_8xx_CPUCLK_MAX
wdenk66ca92a2004-09-28 17:59:53 +0000348 CONFIG_8xx_CPUCLK_DEFAULT
wdenk75d1ea72004-01-31 20:06:54 +0000349 See doc/README.MPC866
350
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200351 CONFIG_SYS_MEASURE_CPUCLK
wdenk75d1ea72004-01-31 20:06:54 +0000352
wdenkba56f622004-02-06 23:19:44 +0000353 Define this to measure the actual CPU clock instead
354 of relying on the correctness of the configured
355 values. Mostly useful for board bringup to make sure
356 the PLL is locked at the intended frequency. Note
357 that this requires a (stable) reference clock (32 kHz
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200358 RTC clock or CONFIG_SYS_8XX_XIN)
wdenk75d1ea72004-01-31 20:06:54 +0000359
Heiko Schocher506f3912009-03-12 07:37:15 +0100360 CONFIG_SYS_DELAYED_ICACHE
361
362 Define this option if you want to enable the
363 ICache only when Code runs from RAM.
364
Kumar Gala66412c62011-02-18 05:40:54 -0600365- 85xx CPU Options:
366 CONFIG_SYS_FSL_TBCLK_DIV
367
368 Defines the core time base clock divider ratio compared to the
369 system clock. On most PQ3 devices this is 8, on newer QorIQ
370 devices it can be 16 or 32. The ratio varies from SoC to Soc.
371
Kumar Gala8f290842011-05-20 00:39:21 -0500372 CONFIG_SYS_FSL_PCIE_COMPAT
373
374 Defines the string to utilize when trying to match PCIe device
375 tree nodes for the given platform.
376
Daniel Schwierzeck6cb461b2012-04-02 02:57:56 +0000377- Generic CPU options:
378 CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
379
380 Defines the endianess of the CPU. Implementation of those
381 values is arch specific.
382
Markus Klotzbuecher0b953ff2006-03-24 15:28:02 +0100383- Intel Monahans options:
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200384 CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
Markus Klotzbuecher0b953ff2006-03-24 15:28:02 +0100385
386 Defines the Monahans run mode to oscillator
387 ratio. Valid values are 8, 16, 24, 31. The core
388 frequency is this value multiplied by 13 MHz.
389
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200390 CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
Wolfgang Denkcf48eb92006-04-16 10:51:58 +0200391
Markus Klotzbuecher0b953ff2006-03-24 15:28:02 +0100392 Defines the Monahans turbo mode to oscillator
393 ratio. Valid values are 1 (default if undefined) and
Wolfgang Denkcf48eb92006-04-16 10:51:58 +0200394 2. The core frequency as calculated above is multiplied
Markus Klotzbuecher0b953ff2006-03-24 15:28:02 +0100395 by this value.
Wolfgang Denkcf48eb92006-04-16 10:51:58 +0200396
Daniel Schwierzeck92bbd642011-07-27 13:22:39 +0200397- MIPS CPU options:
398 CONFIG_SYS_INIT_SP_OFFSET
399
400 Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack
401 pointer. This is needed for the temporary stack before
402 relocation.
403
404 CONFIG_SYS_MIPS_CACHE_MODE
405
406 Cache operation mode for the MIPS CPU.
407 See also arch/mips/include/asm/mipsregs.h.
408 Possible values are:
409 CONF_CM_CACHABLE_NO_WA
410 CONF_CM_CACHABLE_WA
411 CONF_CM_UNCACHED
412 CONF_CM_CACHABLE_NONCOHERENT
413 CONF_CM_CACHABLE_CE
414 CONF_CM_CACHABLE_COW
415 CONF_CM_CACHABLE_CUW
416 CONF_CM_CACHABLE_ACCELERATED
417
418 CONFIG_SYS_XWAY_EBU_BOOTCFG
419
420 Special option for Lantiq XWAY SoCs for booting from NOR flash.
421 See also arch/mips/cpu/mips32/start.S.
422
423 CONFIG_XWAY_SWAP_BYTES
424
425 Enable compilation of tools/xway-swap-bytes needed for Lantiq
426 XWAY SoCs for booting from NOR flash. The U-Boot image needs to
427 be swapped if a flash programmer is used.
428
Christian Rieschb67d8812012-02-02 00:44:39 +0000429- ARM options:
430 CONFIG_SYS_EXCEPTION_VECTORS_HIGH
431
432 Select high exception vectors of the ARM core, e.g., do not
433 clear the V bit of the c1 register of CP15.
434
wdenk5da627a2003-10-09 20:09:04 +0000435- Linux Kernel Interface:
wdenkc6097192002-11-03 00:24:07 +0000436 CONFIG_CLOCKS_IN_MHZ
437
438 U-Boot stores all clock information in Hz
439 internally. For binary compatibility with older Linux
440 kernels (which expect the clocks passed in the
441 bd_info data to be in MHz) the environment variable
442 "clocks_in_mhz" can be defined so that U-Boot
443 converts clock data to MHZ before passing it to the
444 Linux kernel.
wdenkc6097192002-11-03 00:24:07 +0000445 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
Wolfgang Denk218ca722008-03-26 10:40:12 +0100446 "clocks_in_mhz=1" is automatically included in the
wdenkc6097192002-11-03 00:24:07 +0000447 default environment.
448
wdenk5da627a2003-10-09 20:09:04 +0000449 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
450
Marcel Ziswiler11ccc332008-07-09 08:17:15 +0200451 When transferring memsize parameter to linux, some versions
wdenk5da627a2003-10-09 20:09:04 +0000452 expect it to be in bytes, others in MB.
453 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
454
Gerald Van Barenfec6d9e2008-06-03 20:34:45 -0400455 CONFIG_OF_LIBFDT
Wolfgang Denkf57f70a2005-10-13 01:45:54 +0200456
457 New kernel versions are expecting firmware settings to be
Gerald Van Baren213bf8c2007-03-31 12:23:51 -0400458 passed using flattened device trees (based on open firmware
459 concepts).
460
461 CONFIG_OF_LIBFDT
462 * New libfdt-based support
463 * Adds the "fdt" command
Kim Phillips3bb342f2007-08-10 14:34:14 -0500464 * The bootm command automatically updates the fdt
Gerald Van Baren213bf8c2007-03-31 12:23:51 -0400465
Marcel Ziswilerb55ae402009-09-09 21:18:41 +0200466 OF_CPU - The proper name of the cpus node (only required for
467 MPC512X and MPC5xxx based boards).
468 OF_SOC - The proper name of the soc node (only required for
469 MPC512X and MPC5xxx based boards).
Wolfgang Denkf57f70a2005-10-13 01:45:54 +0200470 OF_TBCLK - The timebase frequency.
Kumar Galac2871f02006-01-11 13:59:02 -0600471 OF_STDOUT_PATH - The path to the console device
Wolfgang Denkf57f70a2005-10-13 01:45:54 +0200472
Marcel Ziswiler11ccc332008-07-09 08:17:15 +0200473 boards with QUICC Engines require OF_QE to set UCC MAC
474 addresses
Kim Phillips3bb342f2007-08-10 14:34:14 -0500475
Kumar Gala4e253132006-01-11 13:54:17 -0600476 CONFIG_OF_BOARD_SETUP
477
478 Board code has addition modification that it wants to make
479 to the flat device tree before handing it off to the kernel
wdenk6705d812004-08-02 23:22:59 +0000480
Matthew McClintock02677682006-06-28 10:41:37 -0500481 CONFIG_OF_BOOT_CPU
482
Marcel Ziswiler11ccc332008-07-09 08:17:15 +0200483 This define fills in the correct boot CPU in the boot
Matthew McClintock02677682006-06-28 10:41:37 -0500484 param header, the default value is zero if undefined.
485
Heiko Schocher3887c3f2009-09-23 07:56:08 +0200486 CONFIG_OF_IDE_FIXUP
487
488 U-Boot can detect if an IDE device is present or not.
489 If not, and this new config option is activated, U-Boot
490 removes the ATA node from the DTS before booting Linux,
491 so the Linux IDE driver does not probe the device and
492 crash. This is needed for buggy hardware (uc101) where
493 no pull down resistor is connected to the signal IDE5V_DD7.
494
Igor Grinberg7eb29392011-07-14 05:45:07 +0000495 CONFIG_MACH_TYPE [relevant for ARM only][mandatory]
496
497 This setting is mandatory for all boards that have only one
498 machine type and must be used to specify the machine type
499 number as it appears in the ARM machine registry
500 (see http://www.arm.linux.org.uk/developer/machines/).
501 Only boards that have multiple machine types supported
502 in a single configuration file and the machine type is
503 runtime discoverable, do not have to use this setting.
504
Niklaus Giger0b2f4ec2008-11-03 22:13:47 +0100505- vxWorks boot parameters:
506
507 bootvx constructs a valid bootline using the following
508 environments variables: bootfile, ipaddr, serverip, hostname.
509 It loads the vxWorks image pointed bootfile.
510
511 CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
512 CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
513 CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
514 CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
515
516 CONFIG_SYS_VXWORKS_ADD_PARAMS
517
518 Add it at the end of the bootline. E.g "u=username pw=secret"
519
520 Note: If a "bootargs" environment is defined, it will overwride
521 the defaults discussed just above.
522
Aneesh V2c451f72011-06-16 23:30:47 +0000523- Cache Configuration:
524 CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
525 CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
526 CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
527
Aneesh V93bc2192011-06-16 23:30:51 +0000528- Cache Configuration for ARM:
529 CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
530 controller
531 CONFIG_SYS_PL310_BASE - Physical base address of PL310
532 controller register space
533
wdenk6705d812004-08-02 23:22:59 +0000534- Serial Ports:
Andreas Engel48d01922008-09-08 14:30:53 +0200535 CONFIG_PL010_SERIAL
wdenk6705d812004-08-02 23:22:59 +0000536
537 Define this if you want support for Amba PrimeCell PL010 UARTs.
538
Andreas Engel48d01922008-09-08 14:30:53 +0200539 CONFIG_PL011_SERIAL
wdenk6705d812004-08-02 23:22:59 +0000540
541 Define this if you want support for Amba PrimeCell PL011 UARTs.
542
543 CONFIG_PL011_CLOCK
544
545 If you have Amba PrimeCell PL011 UARTs, set this variable to
546 the clock speed of the UARTs.
547
548 CONFIG_PL01x_PORTS
549
550 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
551 define this to a list of base addresses for each (supported)
552 port. See e.g. include/configs/versatile.h
553
John Rigby910f1ae2011-04-19 10:42:39 +0000554 CONFIG_PL011_SERIAL_RLCR
555
556 Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
557 have separate receive and transmit line control registers. Set
558 this variable to initialize the extra register.
559
560 CONFIG_PL011_SERIAL_FLUSH_ON_INIT
561
562 On some platforms (e.g. U8500) U-Boot is loaded by a second stage
563 boot loader that has already initialized the UART. Define this
564 variable to flush the UART at init time.
565
wdenk6705d812004-08-02 23:22:59 +0000566
wdenkc6097192002-11-03 00:24:07 +0000567- Console Interface:
wdenk43d96162003-03-06 00:02:04 +0000568 Depending on board, define exactly one serial port
569 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
570 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
571 console by defining CONFIG_8xx_CONS_NONE
wdenkc6097192002-11-03 00:24:07 +0000572
573 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
574 port routines must be defined elsewhere
575 (i.e. serial_init(), serial_getc(), ...)
576
577 CONFIG_CFB_CONSOLE
578 Enables console device for a color framebuffer. Needs following
Wolfgang Denkc53043b2011-12-07 12:19:20 +0000579 defines (cf. smiLynxEM, i8042)
wdenkc6097192002-11-03 00:24:07 +0000580 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
581 (default big endian)
582 VIDEO_HW_RECTFILL graphic chip supports
583 rectangle fill
584 (cf. smiLynxEM)
585 VIDEO_HW_BITBLT graphic chip supports
586 bit-blit (cf. smiLynxEM)
587 VIDEO_VISIBLE_COLS visible pixel columns
588 (cols=pitch)
wdenkba56f622004-02-06 23:19:44 +0000589 VIDEO_VISIBLE_ROWS visible pixel rows
590 VIDEO_PIXEL_SIZE bytes per pixel
wdenkc6097192002-11-03 00:24:07 +0000591 VIDEO_DATA_FORMAT graphic data format
592 (0-5, cf. cfb_console.c)
wdenkba56f622004-02-06 23:19:44 +0000593 VIDEO_FB_ADRS framebuffer address
wdenkc6097192002-11-03 00:24:07 +0000594 VIDEO_KBD_INIT_FCT keyboard int fct
595 (i.e. i8042_kbd_init())
596 VIDEO_TSTC_FCT test char fct
597 (i.e. i8042_tstc)
598 VIDEO_GETC_FCT get char fct
599 (i.e. i8042_getc)
600 CONFIG_CONSOLE_CURSOR cursor drawing on/off
601 (requires blink timer
602 cf. i8042.c)
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200603 CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
wdenkc6097192002-11-03 00:24:07 +0000604 CONFIG_CONSOLE_TIME display time/date info in
605 upper right corner
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500606 (requires CONFIG_CMD_DATE)
wdenkc6097192002-11-03 00:24:07 +0000607 CONFIG_VIDEO_LOGO display Linux logo in
608 upper left corner
wdenka6c7ad22002-12-03 21:28:10 +0000609 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
610 linux_logo.h for logo.
611 Requires CONFIG_VIDEO_LOGO
wdenkc6097192002-11-03 00:24:07 +0000612 CONFIG_CONSOLE_EXTRA_INFO
Marcel Ziswiler11ccc332008-07-09 08:17:15 +0200613 additional board info beside
wdenkc6097192002-11-03 00:24:07 +0000614 the logo
615
wdenk43d96162003-03-06 00:02:04 +0000616 When CONFIG_CFB_CONSOLE is defined, video console is
617 default i/o. Serial console can be forced with
618 environment 'console=serial'.
wdenkc6097192002-11-03 00:24:07 +0000619
wdenkd4ca31c2004-01-02 14:00:00 +0000620 When CONFIG_SILENT_CONSOLE is defined, all console
621 messages (by U-Boot and Linux!) can be silenced with
622 the "silent" environment variable. See
623 doc/README.silent for more information.
wdenka3ad8e22003-10-19 23:22:11 +0000624
wdenkc6097192002-11-03 00:24:07 +0000625- Console Baudrate:
626 CONFIG_BAUDRATE - in bps
627 Select one of the baudrates listed in
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200628 CONFIG_SYS_BAUDRATE_TABLE, see below.
629 CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
wdenkc6097192002-11-03 00:24:07 +0000630
Heiko Schocherc92fac92009-01-30 12:55:38 +0100631- Console Rx buffer length
632 With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
633 the maximum receive buffer length for the SMC.
Heiko Schocher2b3f12c2009-02-10 09:31:47 +0100634 This option is actual only for 82xx and 8xx possible.
Heiko Schocherc92fac92009-01-30 12:55:38 +0100635 If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
636 must be defined, to setup the maximum idle timeout for
637 the SMC.
638
Graeme Russ9558b482011-09-01 00:48:27 +0000639- Pre-Console Buffer:
Wolfgang Denk4cf26092011-10-07 09:58:21 +0200640 Prior to the console being initialised (i.e. serial UART
641 initialised etc) all console output is silently discarded.
642 Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to
643 buffer any console messages prior to the console being
644 initialised to a buffer of size CONFIG_PRE_CON_BUF_SZ
645 bytes located at CONFIG_PRE_CON_BUF_ADDR. The buffer is
646 a circular buffer, so if more than CONFIG_PRE_CON_BUF_SZ
Wolfgang Denk6feff892011-10-09 21:06:34 +0200647 bytes are output before the console is initialised, the
Wolfgang Denk4cf26092011-10-07 09:58:21 +0200648 earlier bytes are discarded.
Graeme Russ9558b482011-09-01 00:48:27 +0000649
Wolfgang Denk4cf26092011-10-07 09:58:21 +0200650 'Sane' compilers will generate smaller code if
651 CONFIG_PRE_CON_BUF_SZ is a power of 2
Graeme Russ9558b482011-09-01 00:48:27 +0000652
Sonny Rao046a37b2011-11-02 09:52:08 +0000653- Safe printf() functions
654 Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
655 the printf() functions. These are defined in
656 include/vsprintf.h and include snprintf(), vsnprintf() and
657 so on. Code size increase is approximately 300-500 bytes.
658 If this option is not given then these functions will
659 silently discard their buffer size argument - this means
660 you are not getting any overflow checking in this case.
661
wdenkc6097192002-11-03 00:24:07 +0000662- Boot Delay: CONFIG_BOOTDELAY - in seconds
663 Delay before automatically booting the default image;
664 set to -1 to disable autoboot.
665
666 See doc/README.autoboot for these options that
667 work with CONFIG_BOOTDELAY. None are required.
668 CONFIG_BOOT_RETRY_TIME
669 CONFIG_BOOT_RETRY_MIN
670 CONFIG_AUTOBOOT_KEYED
671 CONFIG_AUTOBOOT_PROMPT
672 CONFIG_AUTOBOOT_DELAY_STR
673 CONFIG_AUTOBOOT_STOP_STR
674 CONFIG_AUTOBOOT_DELAY_STR2
675 CONFIG_AUTOBOOT_STOP_STR2
676 CONFIG_ZERO_BOOTDELAY_CHECK
677 CONFIG_RESET_TO_RETRY
678
679- Autoboot Command:
680 CONFIG_BOOTCOMMAND
681 Only needed when CONFIG_BOOTDELAY is enabled;
682 define a command string that is automatically executed
683 when no character is read on the console interface
684 within "Boot Delay" after reset.
685
686 CONFIG_BOOTARGS
wdenk43d96162003-03-06 00:02:04 +0000687 This can be used to pass arguments to the bootm
688 command. The value of CONFIG_BOOTARGS goes into the
689 environment value "bootargs".
wdenkc6097192002-11-03 00:24:07 +0000690
691 CONFIG_RAMBOOT and CONFIG_NFSBOOT
wdenk43d96162003-03-06 00:02:04 +0000692 The value of these goes into the environment as
693 "ramboot" and "nfsboot" respectively, and can be used
694 as a convenience, when switching between booting from
Marcel Ziswiler11ccc332008-07-09 08:17:15 +0200695 RAM and NFS.
wdenkc6097192002-11-03 00:24:07 +0000696
697- Pre-Boot Commands:
698 CONFIG_PREBOOT
699
700 When this option is #defined, the existence of the
701 environment variable "preboot" will be checked
702 immediately before starting the CONFIG_BOOTDELAY
703 countdown and/or running the auto-boot command resp.
704 entering interactive mode.
705
706 This feature is especially useful when "preboot" is
707 automatically generated or modified. For an example
708 see the LWMON board specific code: here "preboot" is
709 modified when the user holds down a certain
710 combination of keys on the (special) keyboard when
711 booting the systems
712
713- Serial Download Echo Mode:
714 CONFIG_LOADS_ECHO
715 If defined to 1, all characters received during a
716 serial download (using the "loads" command) are
717 echoed back. This might be needed by some terminal
718 emulations (like "cu"), but may as well just take
719 time on others. This setting #define's the initial
720 value of the "loads_echo" environment variable.
721
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500722- Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
wdenkc6097192002-11-03 00:24:07 +0000723 CONFIG_KGDB_BAUDRATE
724 Select one of the baudrates listed in
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200725 CONFIG_SYS_BAUDRATE_TABLE, see below.
wdenkc6097192002-11-03 00:24:07 +0000726
727- Monitor Functions:
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500728 Monitor commands can be included or excluded
729 from the build by using the #include files
730 "config_cmd_all.h" and #undef'ing unwanted
731 commands, or using "config_cmd_default.h"
732 and augmenting with additional #define's
733 for wanted commands.
wdenkc6097192002-11-03 00:24:07 +0000734
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500735 The default command configuration includes all commands
736 except those marked below with a "*".
wdenkc6097192002-11-03 00:24:07 +0000737
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500738 CONFIG_CMD_ASKENV * ask for env variable
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500739 CONFIG_CMD_BDI bdinfo
740 CONFIG_CMD_BEDBUG * Include BedBug Debugger
741 CONFIG_CMD_BMP * BMP support
742 CONFIG_CMD_BSP * Board specific commands
743 CONFIG_CMD_BOOTD bootd
744 CONFIG_CMD_CACHE * icache, dcache
745 CONFIG_CMD_CONSOLE coninfo
Mike Frysinger710b9932010-12-21 14:19:51 -0500746 CONFIG_CMD_CRC32 * crc32
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500747 CONFIG_CMD_DATE * support for RTC, date/time...
748 CONFIG_CMD_DHCP * DHCP support
749 CONFIG_CMD_DIAG * Diagnostics
Peter Tysera7c93102008-12-17 16:36:22 -0600750 CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
751 CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
752 CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
753 CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500754 CONFIG_CMD_DTT * Digital Therm and Thermostat
755 CONFIG_CMD_ECHO echo arguments
Peter Tyser246c6922009-10-25 15:12:56 -0500756 CONFIG_CMD_EDITENV edit env variable
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500757 CONFIG_CMD_EEPROM * EEPROM read/write support
758 CONFIG_CMD_ELF * bootelf, bootvx
Mike Frysinger0c79cda2010-12-26 23:09:45 -0500759 CONFIG_CMD_EXPORTENV * export the environment
Mike Frysingerbdab39d2009-01-28 19:08:14 -0500760 CONFIG_CMD_SAVEENV saveenv
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500761 CONFIG_CMD_FDC * Floppy Disk Support
762 CONFIG_CMD_FAT * FAT partition support
763 CONFIG_CMD_FDOS * Dos diskette Support
764 CONFIG_CMD_FLASH flinfo, erase, protect
765 CONFIG_CMD_FPGA FPGA device initialization support
Mike Frysingera641b972010-12-26 23:32:22 -0500766 CONFIG_CMD_GO * the 'go' command (exec code)
Kim Phillipsa000b792011-04-05 07:15:14 +0000767 CONFIG_CMD_GREPENV * search environment
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500768 CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
769 CONFIG_CMD_I2C * I2C serial bus support
770 CONFIG_CMD_IDE * IDE harddisk support
771 CONFIG_CMD_IMI iminfo
772 CONFIG_CMD_IMLS List all found images
773 CONFIG_CMD_IMMAP * IMMR dump support
Mike Frysinger0c79cda2010-12-26 23:09:45 -0500774 CONFIG_CMD_IMPORTENV * import an environment
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500775 CONFIG_CMD_IRQ * irqinfo
776 CONFIG_CMD_ITEST Integer/string test of 2 values
777 CONFIG_CMD_JFFS2 * JFFS2 Support
778 CONFIG_CMD_KGDB * kgdb
Mike Frysinger1ba7fd22010-12-26 12:34:49 -0500779 CONFIG_CMD_LDRINFO ldrinfo (display Blackfin loader)
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500780 CONFIG_CMD_LOADB loadb
781 CONFIG_CMD_LOADS loads
Robin Getz02c9aa12009-07-27 00:07:59 -0400782 CONFIG_CMD_MD5SUM print md5 message digest
783 (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500784 CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
785 loop, loopw, mtest
786 CONFIG_CMD_MISC Misc functions like sleep etc
787 CONFIG_CMD_MMC * MMC memory mapped support
788 CONFIG_CMD_MII * MII utility commands
Stefan Roese68d7d652009-03-19 13:30:36 +0100789 CONFIG_CMD_MTDPARTS * MTD partition support
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500790 CONFIG_CMD_NAND * NAND support
791 CONFIG_CMD_NET bootp, tftpboot, rarpboot
Peter Tysere92739d2008-12-17 16:36:21 -0600792 CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
Wolfgang Denkc0f40852011-10-26 10:21:21 +0000793 CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500794 CONFIG_CMD_PCI * pciinfo
795 CONFIG_CMD_PCMCIA * PCMCIA support
796 CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
797 host
798 CONFIG_CMD_PORTIO * Port I/O
799 CONFIG_CMD_REGINFO * Register dump
800 CONFIG_CMD_RUN run command in env variable
801 CONFIG_CMD_SAVES * save S record dump
802 CONFIG_CMD_SCSI * SCSI Support
803 CONFIG_CMD_SDRAM * print SDRAM configuration information
804 (requires CONFIG_CMD_I2C)
805 CONFIG_CMD_SETGETDCR Support for DCR Register access
806 (4xx only)
Eric Nelsonf61ec452012-01-31 10:52:08 -0700807 CONFIG_CMD_SF * Read/write/erase SPI NOR flash
Alexander Hollerc6b1ee62011-01-18 09:48:08 +0100808 CONFIG_CMD_SHA1SUM print sha1 memory digest
Robin Getz02c9aa12009-07-27 00:07:59 -0400809 (requires CONFIG_CMD_MEMORY)
Wolfgang Denk74de7ae2009-04-01 23:34:12 +0200810 CONFIG_CMD_SOURCE "source" command Support
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500811 CONFIG_CMD_SPI * SPI serial bus support
Luca Ceresoli7a83af02011-05-17 00:03:40 +0000812 CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
Simon Glass1fb7cd42011-10-24 18:00:07 +0000813 CONFIG_CMD_TFTPPUT * TFTP put command (upload)
Che-liang Chiouca366d02011-10-06 23:40:48 +0000814 CONFIG_CMD_TIME * run command and report execution time
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500815 CONFIG_CMD_USB * USB support
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500816 CONFIG_CMD_CDP * Cisco Discover Protocol support
Marek Vasutc8339f52012-03-31 07:47:16 +0000817 CONFIG_CMD_MFSL * Microblaze FSL support
wdenkc6097192002-11-03 00:24:07 +0000818
wdenkc6097192002-11-03 00:24:07 +0000819
820 EXAMPLE: If you want all functions except of network
821 support you can write:
822
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500823 #include "config_cmd_all.h"
824 #undef CONFIG_CMD_NET
wdenkc6097192002-11-03 00:24:07 +0000825
Gerald Van Baren213bf8c2007-03-31 12:23:51 -0400826 Other Commands:
827 fdt (flattened device tree) command: CONFIG_OF_LIBFDT
wdenkc6097192002-11-03 00:24:07 +0000828
829 Note: Don't enable the "icache" and "dcache" commands
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500830 (configuration option CONFIG_CMD_CACHE) unless you know
wdenk43d96162003-03-06 00:02:04 +0000831 what you (and your U-Boot users) are doing. Data
832 cache cannot be enabled on systems like the 8xx or
833 8260 (where accesses to the IMMR region must be
834 uncached), and it cannot be disabled on all other
835 systems where we (mis-) use the data cache to hold an
836 initial stack and some data.
wdenkc6097192002-11-03 00:24:07 +0000837
838
839 XXX - this list needs to get updated!
840
Simon Glass45ba8072011-10-15 05:48:20 +0000841- Device tree:
842 CONFIG_OF_CONTROL
843 If this variable is defined, U-Boot will use a device tree
844 to configure its devices, instead of relying on statically
845 compiled #defines in the board file. This option is
846 experimental and only available on a few boards. The device
847 tree is available in the global data as gd->fdt_blob.
848
Simon Glass2c0f79e2011-10-24 19:15:31 +0000849 U-Boot needs to get its device tree from somewhere. This can
850 be done using one of the two options below:
Simon Glassbbb0b122011-10-15 05:48:21 +0000851
852 CONFIG_OF_EMBED
853 If this variable is defined, U-Boot will embed a device tree
854 binary in its image. This device tree file should be in the
855 board directory and called <soc>-<board>.dts. The binary file
856 is then picked up in board_init_f() and made available through
857 the global data structure as gd->blob.
Simon Glass45ba8072011-10-15 05:48:20 +0000858
Simon Glass2c0f79e2011-10-24 19:15:31 +0000859 CONFIG_OF_SEPARATE
860 If this variable is defined, U-Boot will build a device tree
861 binary. It will be called u-boot.dtb. Architecture-specific
862 code will locate it at run-time. Generally this works by:
863
864 cat u-boot.bin u-boot.dtb >image.bin
865
866 and in fact, U-Boot does this for you, creating a file called
867 u-boot-dtb.bin which is useful in the common case. You can
868 still use the individual files if you need something more
869 exotic.
870
wdenkc6097192002-11-03 00:24:07 +0000871- Watchdog:
872 CONFIG_WATCHDOG
873 If this variable is defined, it enables watchdog
Detlev Zundel6abe6fb2011-04-27 05:25:59 +0000874 support for the SoC. There must be support in the SoC
875 specific code for a watchdog. For the 8xx and 8260
876 CPUs, the SIU Watchdog feature is enabled in the SYPCR
877 register. When supported for a specific SoC is
878 available, then no further board specific code should
879 be needed to use it.
880
881 CONFIG_HW_WATCHDOG
882 When using a watchdog circuitry external to the used
883 SoC, then define this variable and provide board
884 specific code for the "hw_watchdog_reset" function.
wdenkc6097192002-11-03 00:24:07 +0000885
stroesec1551ea2003-04-04 15:53:41 +0000886- U-Boot Version:
887 CONFIG_VERSION_VARIABLE
888 If this variable is defined, an environment variable
889 named "ver" is created by U-Boot showing the U-Boot
890 version as printed by the "version" command.
891 This variable is readonly.
892
wdenkc6097192002-11-03 00:24:07 +0000893- Real-Time Clock:
894
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500895 When CONFIG_CMD_DATE is selected, the type of the RTC
wdenkc6097192002-11-03 00:24:07 +0000896 has to be selected, too. Define exactly one of the
897 following options:
898
899 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
900 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
Fabio Estevam4e8b7542011-10-24 06:44:15 +0000901 CONFIG_RTC_MC13XXX - use MC13783 or MC13892 RTC
wdenkc6097192002-11-03 00:24:07 +0000902 CONFIG_RTC_MC146818 - use MC146818 RTC
wdenk1cb8e982003-03-06 21:55:29 +0000903 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
wdenkc6097192002-11-03 00:24:07 +0000904 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
wdenk7f70e852003-05-20 14:25:27 +0000905 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
wdenk3bac3512003-03-12 10:41:04 +0000906 CONFIG_RTC_DS164x - use Dallas DS164x RTC
Tor Krill9536dfc2008-03-15 15:40:26 +0100907 CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
wdenk4c0d4c32004-06-09 17:34:58 +0000908 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200909 CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
Heiko Schocher71d19f32011-03-28 09:24:22 +0200910 CONFIG_SYS_RV3029_TCR - enable trickle charger on
911 RV3029 RTC.
wdenkc6097192002-11-03 00:24:07 +0000912
wdenkb37c7e52003-06-30 16:24:52 +0000913 Note that if the RTC uses I2C, then the I2C interface
914 must also be configured. See I2C Support, below.
915
Peter Tysere92739d2008-12-17 16:36:21 -0600916- GPIO Support:
917 CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
918 CONFIG_PCA953X_INFO - enable pca953x info command
919
Chris Packham5dec49c2010-12-19 10:12:13 +0000920 The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
921 chip-ngpio pairs that tell the PCA953X driver the number of
922 pins supported by a particular chip.
923
Peter Tysere92739d2008-12-17 16:36:21 -0600924 Note that if the GPIO device uses I2C, then the I2C interface
925 must also be configured. See I2C Support, below.
926
wdenkc6097192002-11-03 00:24:07 +0000927- Timestamp Support:
928
wdenk43d96162003-03-06 00:02:04 +0000929 When CONFIG_TIMESTAMP is selected, the timestamp
930 (date and time) of an image is printed by image
931 commands like bootm or iminfo. This option is
Jon Loeliger602ad3b2007-06-11 19:03:39 -0500932 automatically enabled when you select CONFIG_CMD_DATE .
wdenkc6097192002-11-03 00:24:07 +0000933
934- Partition Support:
935 CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
richardretanubun07f3d782008-09-26 11:13:22 -0400936 and/or CONFIG_ISO_PARTITION and/or CONFIG_EFI_PARTITION
wdenkc6097192002-11-03 00:24:07 +0000937
Wolfgang Denk218ca722008-03-26 10:40:12 +0100938 If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
939 CONFIG_CMD_SCSI) you must configure support for at
940 least one partition type as well.
wdenkc6097192002-11-03 00:24:07 +0000941
942- IDE Reset method:
wdenk4d13cba2004-03-14 14:09:05 +0000943 CONFIG_IDE_RESET_ROUTINE - this is defined in several
944 board configurations files but used nowhere!
wdenkc6097192002-11-03 00:24:07 +0000945
wdenk4d13cba2004-03-14 14:09:05 +0000946 CONFIG_IDE_RESET - is this is defined, IDE Reset will
947 be performed by calling the function
948 ide_set_reset(int reset)
949 which has to be defined in a board specific file
wdenkc6097192002-11-03 00:24:07 +0000950
951- ATAPI Support:
952 CONFIG_ATAPI
953
954 Set this to enable ATAPI support.
955
wdenkc40b2952004-03-13 23:29:43 +0000956- LBA48 Support
957 CONFIG_LBA48
958
959 Set this to enable support for disks larger than 137GB
Heiko Schocher4b142fe2009-12-03 11:21:21 +0100960 Also look at CONFIG_SYS_64BIT_LBA.
wdenkc40b2952004-03-13 23:29:43 +0000961 Whithout these , LBA48 support uses 32bit variables and will 'only'
962 support disks up to 2.1TB.
963
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200964 CONFIG_SYS_64BIT_LBA:
wdenkc40b2952004-03-13 23:29:43 +0000965 When enabled, makes the IDE subsystem use 64bit sector addresses.
966 Default is 32bit.
967
wdenkc6097192002-11-03 00:24:07 +0000968- SCSI Support:
969 At the moment only there is only support for the
970 SYM53C8XX SCSI controller; define
971 CONFIG_SCSI_SYM53C8XX to enable it.
972
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200973 CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
974 CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
975 CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
wdenkc6097192002-11-03 00:24:07 +0000976 maximum numbers of LUNs, SCSI ID's and target
977 devices.
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +0200978 CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
wdenkc6097192002-11-03 00:24:07 +0000979
980- NETWORK Support (PCI):
wdenk682011f2003-06-03 23:54:09 +0000981 CONFIG_E1000
Kyle Moffettce5207e2011-10-18 11:05:29 +0000982 Support for Intel 8254x/8257x gigabit chips.
983
984 CONFIG_E1000_SPI
985 Utility code for direct access to the SPI bus on Intel 8257x.
986 This does not do anything useful unless you set at least one
987 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
988
989 CONFIG_E1000_SPI_GENERIC
990 Allow generic access to the SPI bus on the Intel 8257x, for
991 example with the "sspi" command.
992
993 CONFIG_CMD_E1000
994 Management command for E1000 devices. When used on devices
995 with SPI support you can reprogram the EEPROM from U-Boot.
stroese53cf9432003-06-05 15:39:44 +0000996
Andre Schwarzac3315c2008-03-06 16:45:44 +0100997 CONFIG_E1000_FALLBACK_MAC
Marcel Ziswiler11ccc332008-07-09 08:17:15 +0200998 default MAC for empty EEPROM after production.
Andre Schwarzac3315c2008-03-06 16:45:44 +0100999
wdenkc6097192002-11-03 00:24:07 +00001000 CONFIG_EEPRO100
1001 Support for Intel 82557/82559/82559ER chips.
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02001002 Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
wdenkc6097192002-11-03 00:24:07 +00001003 write routine for first time initialisation.
1004
1005 CONFIG_TULIP
1006 Support for Digital 2114x chips.
1007 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
1008 modem chip initialisation (KS8761/QS6611).
1009
1010 CONFIG_NATSEMI
1011 Support for National dp83815 chips.
1012
1013 CONFIG_NS8382X
1014 Support for National dp8382[01] gigabit chips.
1015
wdenk45219c42003-05-12 21:50:16 +00001016- NETWORK Support (other):
1017
Jens Scharsigc041e9d2010-01-23 12:03:45 +01001018 CONFIG_DRIVER_AT91EMAC
1019 Support for AT91RM9200 EMAC.
1020
1021 CONFIG_RMII
1022 Define this to use reduced MII inteface
1023
1024 CONFIG_DRIVER_AT91EMAC_QUIET
1025 If this defined, the driver is quiet.
1026 The driver doen't show link status messages.
1027
Rob Herringefdd7312011-12-15 11:15:49 +00001028 CONFIG_CALXEDA_XGMAC
1029 Support for the Calxeda XGMAC device
1030
wdenk45219c42003-05-12 21:50:16 +00001031 CONFIG_DRIVER_LAN91C96
1032 Support for SMSC's LAN91C96 chips.
1033
1034 CONFIG_LAN91C96_BASE
1035 Define this to hold the physical address
1036 of the LAN91C96's I/O space
1037
1038 CONFIG_LAN91C96_USE_32_BIT
1039 Define this to enable 32 bit addressing
1040
wdenkf39748a2004-06-09 13:37:52 +00001041 CONFIG_DRIVER_SMC91111
1042 Support for SMSC's LAN91C111 chip
1043
1044 CONFIG_SMC91111_BASE
1045 Define this to hold the physical address
1046 of the device (I/O space)
1047
1048 CONFIG_SMC_USE_32_BIT
1049 Define this if data bus is 32 bits
1050
1051 CONFIG_SMC_USE_IOFUNCS
1052 Define this to use i/o functions instead of macros
1053 (some hardware wont work with macros)
1054
Heiko Schocherdc02bad2011-11-15 10:00:04 -05001055 CONFIG_DRIVER_TI_EMAC
1056 Support for davinci emac
1057
1058 CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
1059 Define this if you have more then 3 PHYs.
1060
Macpaul Linb3dbf4a52010-12-21 16:59:46 +08001061 CONFIG_FTGMAC100
1062 Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
1063
1064 CONFIG_FTGMAC100_EGIGA
1065 Define this to use GE link update with gigabit PHY.
1066 Define this if FTGMAC100 is connected to gigabit PHY.
1067 If your system has 10/100 PHY only, it might not occur
1068 wrong behavior. Because PHY usually return timeout or
1069 useless data when polling gigabit status and gigabit
1070 control registers. This behavior won't affect the
1071 correctnessof 10/100 link speed update.
1072
Mike Rapoportc2fff332009-11-11 10:03:03 +02001073 CONFIG_SMC911X
Jens Gehrlein557b3772008-05-05 14:06:11 +02001074 Support for SMSC's LAN911x and LAN921x chips
1075
Mike Rapoportc2fff332009-11-11 10:03:03 +02001076 CONFIG_SMC911X_BASE
Jens Gehrlein557b3772008-05-05 14:06:11 +02001077 Define this to hold the physical address
1078 of the device (I/O space)
1079
Mike Rapoportc2fff332009-11-11 10:03:03 +02001080 CONFIG_SMC911X_32_BIT
Jens Gehrlein557b3772008-05-05 14:06:11 +02001081 Define this if data bus is 32 bits
1082
Mike Rapoportc2fff332009-11-11 10:03:03 +02001083 CONFIG_SMC911X_16_BIT
Jens Gehrlein557b3772008-05-05 14:06:11 +02001084 Define this if data bus is 16 bits. If your processor
1085 automatically converts one 32 bit word to two 16 bit
Mike Rapoportc2fff332009-11-11 10:03:03 +02001086 words you may also try CONFIG_SMC911X_32_BIT.
Jens Gehrlein557b3772008-05-05 14:06:11 +02001087
Yoshihiro Shimoda3d0075f2011-01-27 10:06:03 +09001088 CONFIG_SH_ETHER
1089 Support for Renesas on-chip Ethernet controller
1090
1091 CONFIG_SH_ETHER_USE_PORT
1092 Define the number of ports to be used
1093
1094 CONFIG_SH_ETHER_PHY_ADDR
1095 Define the ETH PHY's address
1096
Yoshihiro Shimoda68260aa2011-01-27 10:06:08 +09001097 CONFIG_SH_ETHER_CACHE_WRITEBACK
1098 If this option is set, the driver enables cache flush.
1099
Vadim Bendebury5e124722011-10-17 08:36:14 +00001100- TPM Support:
1101 CONFIG_GENERIC_LPC_TPM
1102 Support for generic parallel port TPM devices. Only one device
1103 per system is supported at this time.
1104
1105 CONFIG_TPM_TIS_BASE_ADDRESS
1106 Base address where the generic TPM device is mapped
1107 to. Contemporary x86 systems usually map it at
1108 0xfed40000.
1109
wdenkc6097192002-11-03 00:24:07 +00001110- USB Support:
1111 At the moment only the UHCI host controller is
wdenk4d13cba2004-03-14 14:09:05 +00001112 supported (PIP405, MIP405, MPC5200); define
wdenkc6097192002-11-03 00:24:07 +00001113 CONFIG_USB_UHCI to enable it.
1114 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
wdenk30d56fa2004-10-09 22:44:59 +00001115 and define CONFIG_USB_STORAGE to enable the USB
wdenkc6097192002-11-03 00:24:07 +00001116 storage devices.
1117 Note:
1118 Supported are USB Keyboards and USB Floppy drives
1119 (TEAC FD-05PUB).
wdenk4d13cba2004-03-14 14:09:05 +00001120 MPC5200 USB requires additional defines:
1121 CONFIG_USB_CLOCK
1122 for 528 MHz Clock: 0x0001bbbb
Eric Millbrandt307ecb62009-08-13 08:32:37 -05001123 CONFIG_PSC3_USB
1124 for USB on PSC3
wdenk4d13cba2004-03-14 14:09:05 +00001125 CONFIG_USB_CONFIG
1126 for differential drivers: 0x00001000
1127 for single ended drivers: 0x00005000
Eric Millbrandt307ecb62009-08-13 08:32:37 -05001128 for differential drivers on PSC3: 0x00000100
1129 for single ended drivers on PSC3: 0x00004100
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001130 CONFIG_SYS_USB_EVENT_POLL
Zhang Weifdcfaa12007-06-06 10:08:13 +02001131 May be defined to allow interrupt polling
1132 instead of using asynchronous interrupts
wdenk4d13cba2004-03-14 14:09:05 +00001133
Simon Glass9ab4ce22012-02-27 10:52:47 +00001134 CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
1135 txfilltuning field in the EHCI controller on reset.
1136
Wolfgang Denk16c8d5e2006-06-14 17:45:53 +02001137- USB Device:
1138 Define the below if you wish to use the USB console.
1139 Once firmware is rebuilt from a serial console issue the
1140 command "setenv stdin usbtty; setenv stdout usbtty" and
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02001141 attach your USB cable. The Unix command "dmesg" should print
Wolfgang Denk16c8d5e2006-06-14 17:45:53 +02001142 it has found a new device. The environment variable usbtty
1143 can be set to gserial or cdc_acm to enable your device to
Wolfgang Denk386eda02006-06-14 18:14:56 +02001144 appear to a USB host as a Linux gserial device or a
Wolfgang Denk16c8d5e2006-06-14 17:45:53 +02001145 Common Device Class Abstract Control Model serial device.
1146 If you select usbtty = gserial you should be able to enumerate
1147 a Linux host by
1148 # modprobe usbserial vendor=0xVendorID product=0xProductID
1149 else if using cdc_acm, simply setting the environment
1150 variable usbtty to be cdc_acm should suffice. The following
1151 might be defined in YourBoardName.h
Wolfgang Denk386eda02006-06-14 18:14:56 +02001152
Wolfgang Denk16c8d5e2006-06-14 17:45:53 +02001153 CONFIG_USB_DEVICE
1154 Define this to build a UDC device
wdenkc6097192002-11-03 00:24:07 +00001155
Wolfgang Denk16c8d5e2006-06-14 17:45:53 +02001156 CONFIG_USB_TTY
1157 Define this to have a tty type of device available to
1158 talk to the UDC device
Wolfgang Denk386eda02006-06-14 18:14:56 +02001159
Vipin KUMARf9da0f82012-03-26 15:38:06 +05301160 CONFIG_USBD_HS
1161 Define this to enable the high speed support for usb
1162 device and usbtty. If this feature is enabled, a routine
1163 int is_usbd_high_speed(void)
1164 also needs to be defined by the driver to dynamically poll
1165 whether the enumeration has succeded at high speed or full
1166 speed.
1167
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001168 CONFIG_SYS_CONSOLE_IS_IN_ENV
Wolfgang Denk16c8d5e2006-06-14 17:45:53 +02001169 Define this if you want stdin, stdout &/or stderr to
1170 be set to usbtty.
1171
1172 mpc8xx:
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001173 CONFIG_SYS_USB_EXTC_CLK 0xBLAH
Wolfgang Denk16c8d5e2006-06-14 17:45:53 +02001174 Derive USB clock from external clock "blah"
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001175 - CONFIG_SYS_USB_EXTC_CLK 0x02
Wolfgang Denk386eda02006-06-14 18:14:56 +02001176
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001177 CONFIG_SYS_USB_BRG_CLK 0xBLAH
Wolfgang Denk16c8d5e2006-06-14 17:45:53 +02001178 Derive USB clock from brgclk
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001179 - CONFIG_SYS_USB_BRG_CLK 0x04
Wolfgang Denk16c8d5e2006-06-14 17:45:53 +02001180
Wolfgang Denk386eda02006-06-14 18:14:56 +02001181 If you have a USB-IF assigned VendorID then you may wish to
Wolfgang Denk16c8d5e2006-06-14 17:45:53 +02001182 define your own vendor specific values either in BoardName.h
Wolfgang Denk386eda02006-06-14 18:14:56 +02001183 or directly in usbd_vendor_info.h. If you don't define
Wolfgang Denk16c8d5e2006-06-14 17:45:53 +02001184 CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
1185 CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
1186 should pretend to be a Linux device to it's target host.
1187
1188 CONFIG_USBD_MANUFACTURER
1189 Define this string as the name of your company for
1190 - CONFIG_USBD_MANUFACTURER "my company"
Wolfgang Denk386eda02006-06-14 18:14:56 +02001191
Wolfgang Denk16c8d5e2006-06-14 17:45:53 +02001192 CONFIG_USBD_PRODUCT_NAME
1193 Define this string as the name of your product
1194 - CONFIG_USBD_PRODUCT_NAME "acme usb device"
1195
1196 CONFIG_USBD_VENDORID
1197 Define this as your assigned Vendor ID from the USB
1198 Implementors Forum. This *must* be a genuine Vendor ID
1199 to avoid polluting the USB namespace.
1200 - CONFIG_USBD_VENDORID 0xFFFF
Wolfgang Denk386eda02006-06-14 18:14:56 +02001201
Wolfgang Denk16c8d5e2006-06-14 17:45:53 +02001202 CONFIG_USBD_PRODUCTID
1203 Define this as the unique Product ID
1204 for your device
1205 - CONFIG_USBD_PRODUCTID 0xFFFF
wdenkc6097192002-11-03 00:24:07 +00001206
Igor Grinbergd70a5602011-12-12 12:08:35 +02001207- ULPI Layer Support:
1208 The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
1209 the generic ULPI layer. The generic layer accesses the ULPI PHY
1210 via the platform viewport, so you need both the genric layer and
1211 the viewport enabled. Currently only Chipidea/ARC based
1212 viewport is supported.
1213 To enable the ULPI layer support, define CONFIG_USB_ULPI and
1214 CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
wdenkc6097192002-11-03 00:24:07 +00001215
1216- MMC Support:
1217 The MMC controller on the Intel PXA is supported. To
1218 enable this define CONFIG_MMC. The MMC can be
1219 accessed from the boot prompt by mapping the device
1220 to physical memory similar to flash. Command line is
Jon Loeliger602ad3b2007-06-11 19:03:39 -05001221 enabled with CONFIG_CMD_MMC. The MMC driver also works with
1222 the FAT fs. This is enabled with CONFIG_CMD_FAT.
wdenkc6097192002-11-03 00:24:07 +00001223
Yoshihiro Shimodaafb35662011-07-04 22:21:22 +00001224 CONFIG_SH_MMCIF
1225 Support for Renesas on-chip MMCIF controller
1226
1227 CONFIG_SH_MMCIF_ADDR
1228 Define the base address of MMCIF registers
1229
1230 CONFIG_SH_MMCIF_CLK
1231 Define the clock frequency for MMCIF
1232
wdenk6705d812004-08-02 23:22:59 +00001233- Journaling Flash filesystem support:
1234 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
1235 CONFIG_JFFS2_NAND_DEV
1236 Define these for a default partition on a NAND device
1237
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001238 CONFIG_SYS_JFFS2_FIRST_SECTOR,
1239 CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
wdenk6705d812004-08-02 23:22:59 +00001240 Define these for a default partition on a NOR device
1241
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001242 CONFIG_SYS_JFFS_CUSTOM_PART
wdenk6705d812004-08-02 23:22:59 +00001243 Define this to create an own partition. You have to provide a
1244 function struct part_info* jffs2_part_info(int part_num)
1245
1246 If you define only one JFFS2 partition you may also want to
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001247 #define CONFIG_SYS_JFFS_SINGLE_PART 1
wdenk6705d812004-08-02 23:22:59 +00001248 to disable the command chpart. This is the default when you
1249 have not defined a custom partition
1250
Donggeun Kimc30a15e2011-10-24 21:15:28 +00001251- FAT(File Allocation Table) filesystem write function support:
1252 CONFIG_FAT_WRITE
Donggeun Kim656f4c62012-03-22 04:38:56 +00001253
1254 Define this to enable support for saving memory data as a
1255 file in FAT formatted partition.
1256
1257 This will also enable the command "fatwrite" enabling the
1258 user to write files to FAT.
Donggeun Kimc30a15e2011-10-24 21:15:28 +00001259
wdenkc6097192002-11-03 00:24:07 +00001260- Keyboard Support:
1261 CONFIG_ISA_KEYBOARD
1262
1263 Define this to enable standard (PC-Style) keyboard
1264 support
1265
1266 CONFIG_I8042_KBD
1267 Standard PC keyboard driver with US (is default) and
1268 GERMAN key layout (switch via environment 'keymap=de') support.
1269 Export function i8042_kbd_init, i8042_tstc and i8042_getc
1270 for cfb_console. Supports cursor blinking.
1271
1272- Video support:
1273 CONFIG_VIDEO
1274
1275 Define this to enable video support (for output to
1276 video).
1277
1278 CONFIG_VIDEO_CT69000
1279
1280 Enable Chips & Technologies 69000 Video chip
1281
1282 CONFIG_VIDEO_SMI_LYNXEM
wdenkb79a11c2004-03-25 15:14:43 +00001283 Enable Silicon Motion SMI 712/710/810 Video chip. The
wdenkeeb1b772004-03-23 22:53:55 +00001284 video output is selected via environment 'videoout'
1285 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
1286 assumed.
wdenkc6097192002-11-03 00:24:07 +00001287
wdenkb79a11c2004-03-25 15:14:43 +00001288 For the CT69000 and SMI_LYNXEM drivers, videomode is
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02001289 selected via environment 'videomode'. Two different ways
wdenkeeb1b772004-03-23 22:53:55 +00001290 are possible:
1291 - "videomode=num" 'num' is a standard LiLo mode numbers.
wdenk6e592382004-04-18 17:39:38 +00001292 Following standard modes are supported (* is default):
wdenkeeb1b772004-03-23 22:53:55 +00001293
1294 Colors 640x480 800x600 1024x768 1152x864 1280x1024
1295 -------------+---------------------------------------------
1296 8 bits | 0x301* 0x303 0x305 0x161 0x307
1297 15 bits | 0x310 0x313 0x316 0x162 0x319
1298 16 bits | 0x311 0x314 0x317 0x163 0x31A
1299 24 bits | 0x312 0x315 0x318 ? 0x31B
1300 -------------+---------------------------------------------
wdenkc6097192002-11-03 00:24:07 +00001301 (i.e. setenv videomode 317; saveenv; reset;)
1302
wdenkb79a11c2004-03-25 15:14:43 +00001303 - "videomode=bootargs" all the video parameters are parsed
Marcel Ziswiler7817cb22007-12-30 03:30:46 +01001304 from the bootargs. (See drivers/video/videomodes.c)
wdenkeeb1b772004-03-23 22:53:55 +00001305
1306
stroesec1551ea2003-04-04 15:53:41 +00001307 CONFIG_VIDEO_SED13806
wdenk43d96162003-03-06 00:02:04 +00001308 Enable Epson SED13806 driver. This driver supports 8bpp
wdenka6c7ad22002-12-03 21:28:10 +00001309 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
1310 or CONFIG_VIDEO_SED13806_16BPP
1311
Timur Tabi7d3053f2011-02-15 17:09:19 -06001312 CONFIG_FSL_DIU_FB
Wolfgang Denk04e5ae72011-09-11 21:24:09 +02001313 Enable the Freescale DIU video driver. Reference boards for
Timur Tabi7d3053f2011-02-15 17:09:19 -06001314 SOCs that have a DIU should define this macro to enable DIU
1315 support, and should also define these other macros:
1316
1317 CONFIG_SYS_DIU_ADDR
1318 CONFIG_VIDEO
1319 CONFIG_CMD_BMP
1320 CONFIG_CFB_CONSOLE
1321 CONFIG_VIDEO_SW_CURSOR
1322 CONFIG_VGA_AS_SINGLE_DEVICE
1323 CONFIG_VIDEO_LOGO
1324 CONFIG_VIDEO_BMP_LOGO
1325
Timur Tabiba8e76b2011-04-11 14:18:22 -05001326 The DIU driver will look for the 'video-mode' environment
1327 variable, and if defined, enable the DIU as a console during
1328 boot. See the documentation file README.video for a
1329 description of this variable.
Timur Tabi7d3053f2011-02-15 17:09:19 -06001330
wdenk682011f2003-06-03 23:54:09 +00001331- Keyboard Support:
wdenk8bde7f72003-06-27 21:31:46 +00001332 CONFIG_KEYBOARD
wdenk682011f2003-06-03 23:54:09 +00001333
wdenk8bde7f72003-06-27 21:31:46 +00001334 Define this to enable a custom keyboard support.
1335 This simply calls drv_keyboard_init() which must be
1336 defined in your board-specific files.
1337 The only board using this so far is RBC823.
wdenka6c7ad22002-12-03 21:28:10 +00001338
wdenkc6097192002-11-03 00:24:07 +00001339- LCD Support: CONFIG_LCD
1340
1341 Define this to enable LCD support (for output to LCD
1342 display); also select one of the supported displays
1343 by defining one of these:
1344
Stelian Pop39cf4802008-05-09 21:57:18 +02001345 CONFIG_ATMEL_LCD:
1346
1347 HITACHI TX09D70VM1CCA, 3.5", 240x320.
1348
wdenkfd3103b2003-11-25 16:55:19 +00001349 CONFIG_NEC_NL6448AC33:
wdenkc6097192002-11-03 00:24:07 +00001350
wdenkfd3103b2003-11-25 16:55:19 +00001351 NEC NL6448AC33-18. Active, color, single scan.
wdenkc6097192002-11-03 00:24:07 +00001352
wdenkfd3103b2003-11-25 16:55:19 +00001353 CONFIG_NEC_NL6448BC20
wdenkc6097192002-11-03 00:24:07 +00001354
wdenkfd3103b2003-11-25 16:55:19 +00001355 NEC NL6448BC20-08. 6.5", 640x480.
1356 Active, color, single scan.
1357
1358 CONFIG_NEC_NL6448BC33_54
1359
1360 NEC NL6448BC33-54. 10.4", 640x480.
wdenkc6097192002-11-03 00:24:07 +00001361 Active, color, single scan.
1362
1363 CONFIG_SHARP_16x9
1364
1365 Sharp 320x240. Active, color, single scan.
1366 It isn't 16x9, and I am not sure what it is.
1367
1368 CONFIG_SHARP_LQ64D341
1369
1370 Sharp LQ64D341 display, 640x480.
1371 Active, color, single scan.
1372
1373 CONFIG_HLD1045
1374
1375 HLD1045 display, 640x480.
1376 Active, color, single scan.
1377
1378 CONFIG_OPTREX_BW
1379
1380 Optrex CBL50840-2 NF-FW 99 22 M5
1381 or
1382 Hitachi LMG6912RPFC-00T
1383 or
1384 Hitachi SP14Q002
1385
1386 320x240. Black & white.
1387
1388 Normally display is black on white background; define
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001389 CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
wdenkc6097192002-11-03 00:24:07 +00001390
wdenk7152b1d2003-09-05 23:19:14 +00001391- Splash Screen Support: CONFIG_SPLASH_SCREEN
wdenkd791b1d2003-04-20 14:04:18 +00001392
wdenk8bde7f72003-06-27 21:31:46 +00001393 If this option is set, the environment is checked for
1394 a variable "splashimage". If found, the usual display
1395 of logo, copyright and system information on the LCD
wdenke94d2cd2004-06-30 22:59:18 +00001396 is suppressed and the BMP image at the address
wdenk8bde7f72003-06-27 21:31:46 +00001397 specified in "splashimage" is loaded instead. The
1398 console is redirected to the "nulldev", too. This
1399 allows for a "silent" boot where a splash screen is
1400 loaded very quickly after power-on.
wdenkd791b1d2003-04-20 14:04:18 +00001401
Matthias Weisser1ca298c2009-07-09 16:07:30 +02001402 CONFIG_SPLASH_SCREEN_ALIGN
1403
1404 If this option is set the splash image can be freely positioned
1405 on the screen. Environment variable "splashpos" specifies the
1406 position as "x,y". If a positive number is given it is used as
1407 number of pixel from left/top. If a negative number is given it
1408 is used as number of pixel from right/bottom. You can also
1409 specify 'm' for centering the image.
1410
1411 Example:
1412 setenv splashpos m,m
1413 => image at center of screen
1414
1415 setenv splashpos 30,20
1416 => image at x = 30 and y = 20
1417
1418 setenv splashpos -10,m
1419 => vertically centered image
1420 at x = dspWidth - bmpWidth - 9
1421
Stefan Roese98f4a3d2005-09-22 09:04:17 +02001422- Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
1423
1424 If this option is set, additionally to standard BMP
1425 images, gzipped BMP images can be displayed via the
1426 splashscreen support or the bmp command.
1427
Anatolij Gustschind5011762010-03-15 14:50:25 +01001428- Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8
1429
1430 If this option is set, 8-bit RLE compressed BMP images
1431 can be displayed via the splashscreen support or the
1432 bmp command.
1433
wdenkc29fdfc2003-08-29 20:57:53 +00001434- Compression support:
1435 CONFIG_BZIP2
1436
1437 If this option is set, support for bzip2 compressed
1438 images is included. If not, only uncompressed and gzip
1439 compressed images are supported.
1440
wdenk42d1f032003-10-15 23:53:47 +00001441 NOTE: the bzip2 algorithm requires a lot of RAM, so
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001442 the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
wdenk42d1f032003-10-15 23:53:47 +00001443 be at least 4MB.
wdenkd791b1d2003-04-20 14:04:18 +00001444
Luigi 'Comio' Mantellinifc9c1722008-09-08 02:46:13 +02001445 CONFIG_LZMA
1446
1447 If this option is set, support for lzma compressed
1448 images is included.
1449
1450 Note: The LZMA algorithm adds between 2 and 4KB of code and it
1451 requires an amount of dynamic memory that is given by the
1452 formula:
1453
1454 (1846 + 768 << (lc + lp)) * sizeof(uint16)
1455
1456 Where lc and lp stand for, respectively, Literal context bits
1457 and Literal pos bits.
1458
1459 This value is upper-bounded by 14MB in the worst case. Anyway,
1460 for a ~4MB large kernel image, we have lc=3 and lp=0 for a
1461 total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
1462 a very small buffer.
1463
1464 Use the lzmainfo tool to determinate the lc and lp values and
1465 then calculate the amount of needed dynamic memory (ensuring
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001466 the appropriate CONFIG_SYS_MALLOC_LEN value).
Luigi 'Comio' Mantellinifc9c1722008-09-08 02:46:13 +02001467
wdenk17ea1172004-06-06 21:51:03 +00001468- MII/PHY support:
1469 CONFIG_PHY_ADDR
1470
1471 The address of PHY on MII bus.
1472
1473 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
1474
1475 The clock frequency of the MII bus
1476
1477 CONFIG_PHY_GIGE
1478
1479 If this option is set, support for speed/duplex
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02001480 detection of gigabit PHY is included.
wdenk17ea1172004-06-06 21:51:03 +00001481
1482 CONFIG_PHY_RESET_DELAY
1483
1484 Some PHY like Intel LXT971A need extra delay after
1485 reset before any MII register access is possible.
1486 For such PHY, set this option to the usec delay
1487 required. (minimum 300usec for LXT971A)
1488
1489 CONFIG_PHY_CMD_DELAY (ppc4xx)
1490
1491 Some PHY like Intel LXT971A need extra delay after
1492 command issued before MII status register can be read
1493
wdenkc6097192002-11-03 00:24:07 +00001494- Ethernet address:
1495 CONFIG_ETHADDR
richardretanubunc68a05f2008-09-29 18:28:23 -04001496 CONFIG_ETH1ADDR
wdenkc6097192002-11-03 00:24:07 +00001497 CONFIG_ETH2ADDR
1498 CONFIG_ETH3ADDR
richardretanubunc68a05f2008-09-29 18:28:23 -04001499 CONFIG_ETH4ADDR
1500 CONFIG_ETH5ADDR
wdenkc6097192002-11-03 00:24:07 +00001501
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02001502 Define a default value for Ethernet address to use
1503 for the respective Ethernet interface, in case this
wdenkc6097192002-11-03 00:24:07 +00001504 is not determined automatically.
1505
1506- IP address:
1507 CONFIG_IPADDR
1508
1509 Define a default value for the IP address to use for
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02001510 the default Ethernet interface, in case this is not
wdenkc6097192002-11-03 00:24:07 +00001511 determined through e.g. bootp.
Wolfgang Denk1ebcd652011-10-26 10:21:22 +00001512 (Environment variable "ipaddr")
wdenkc6097192002-11-03 00:24:07 +00001513
1514- Server IP address:
1515 CONFIG_SERVERIP
1516
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02001517 Defines a default value for the IP address of a TFTP
wdenkc6097192002-11-03 00:24:07 +00001518 server to contact when using the "tftboot" command.
Wolfgang Denk1ebcd652011-10-26 10:21:22 +00001519 (Environment variable "serverip")
wdenkc6097192002-11-03 00:24:07 +00001520
Robin Getz97cfe862009-07-21 12:15:28 -04001521 CONFIG_KEEP_SERVERADDR
1522
1523 Keeps the server's MAC address, in the env 'serveraddr'
1524 for passing to bootargs (like Linux's netconsole option)
1525
Wolfgang Denk1ebcd652011-10-26 10:21:22 +00001526- Gateway IP address:
1527 CONFIG_GATEWAYIP
1528
1529 Defines a default value for the IP address of the
1530 default router where packets to other networks are
1531 sent to.
1532 (Environment variable "gatewayip")
1533
1534- Subnet mask:
1535 CONFIG_NETMASK
1536
1537 Defines a default value for the subnet mask (or
1538 routing prefix) which is used to determine if an IP
1539 address belongs to the local subnet or needs to be
1540 forwarded through a router.
1541 (Environment variable "netmask")
1542
David Updegraff53a5c422007-06-11 10:41:07 -05001543- Multicast TFTP Mode:
1544 CONFIG_MCAST_TFTP
1545
1546 Defines whether you want to support multicast TFTP as per
1547 rfc-2090; for example to work with atftp. Lets lots of targets
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02001548 tftp down the same boot image concurrently. Note: the Ethernet
David Updegraff53a5c422007-06-11 10:41:07 -05001549 driver in use must provide a function: mcast() to join/leave a
1550 multicast group.
1551
wdenkc6097192002-11-03 00:24:07 +00001552- BOOTP Recovery Mode:
1553 CONFIG_BOOTP_RANDOM_DELAY
1554
1555 If you have many targets in a network that try to
1556 boot using BOOTP, you may want to avoid that all
1557 systems send out BOOTP requests at precisely the same
1558 moment (which would happen for instance at recovery
1559 from a power failure, when all systems will try to
1560 boot, thus flooding the BOOTP server. Defining
1561 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1562 inserted before sending out BOOTP requests. The
Wolfgang Denk6c33c782007-08-06 23:21:05 +02001563 following delays are inserted then:
wdenkc6097192002-11-03 00:24:07 +00001564
1565 1st BOOTP request: delay 0 ... 1 sec
1566 2nd BOOTP request: delay 0 ... 2 sec
1567 3rd BOOTP request: delay 0 ... 4 sec
1568 4th and following
1569 BOOTP requests: delay 0 ... 8 sec
1570
stroesefe389a82003-08-28 14:17:32 +00001571- DHCP Advanced Options:
Jon Loeliger1fe80d72007-07-09 22:08:34 -05001572 You can fine tune the DHCP functionality by defining
1573 CONFIG_BOOTP_* symbols:
stroesefe389a82003-08-28 14:17:32 +00001574
Jon Loeliger1fe80d72007-07-09 22:08:34 -05001575 CONFIG_BOOTP_SUBNETMASK
1576 CONFIG_BOOTP_GATEWAY
1577 CONFIG_BOOTP_HOSTNAME
1578 CONFIG_BOOTP_NISDOMAIN
1579 CONFIG_BOOTP_BOOTPATH
1580 CONFIG_BOOTP_BOOTFILESIZE
1581 CONFIG_BOOTP_DNS
1582 CONFIG_BOOTP_DNS2
1583 CONFIG_BOOTP_SEND_HOSTNAME
1584 CONFIG_BOOTP_NTPSERVER
1585 CONFIG_BOOTP_TIMEOFFSET
1586 CONFIG_BOOTP_VENDOREX
stroesefe389a82003-08-28 14:17:32 +00001587
Wilson Callan5d110f02007-07-28 10:56:13 -04001588 CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
1589 environment variable, not the BOOTP server.
stroesefe389a82003-08-28 14:17:32 +00001590
1591 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1592 serverip from a DHCP server, it is possible that more
1593 than one DNS serverip is offered to the client.
1594 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1595 serverip will be stored in the additional environment
1596 variable "dnsip2". The first DNS serverip is always
1597 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
Jon Loeliger1fe80d72007-07-09 22:08:34 -05001598 is defined.
stroesefe389a82003-08-28 14:17:32 +00001599
1600 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1601 to do a dynamic update of a DNS server. To do this, they
1602 need the hostname of the DHCP requester.
Wilson Callan5d110f02007-07-28 10:56:13 -04001603 If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
Jon Loeliger1fe80d72007-07-09 22:08:34 -05001604 of the "hostname" environment variable is passed as
1605 option 12 to the DHCP server.
stroesefe389a82003-08-28 14:17:32 +00001606
Aras Vaichasd9a2f412008-03-26 09:43:57 +11001607 CONFIG_BOOTP_DHCP_REQUEST_DELAY
1608
1609 A 32bit value in microseconds for a delay between
1610 receiving a "DHCP Offer" and sending the "DHCP Request".
1611 This fixes a problem with certain DHCP servers that don't
1612 respond 100% of the time to a "DHCP request". E.g. On an
1613 AT91RM9200 processor running at 180MHz, this delay needed
1614 to be *at least* 15,000 usec before a Windows Server 2003
1615 DHCP server would reply 100% of the time. I recommend at
1616 least 50,000 usec to be safe. The alternative is to hope
1617 that one of the retries will be successful but note that
1618 the DHCP timeout and retry process takes a longer than
1619 this delay.
1620
wdenka3d991b2004-04-15 21:48:45 +00001621 - CDP Options:
wdenk6e592382004-04-18 17:39:38 +00001622 CONFIG_CDP_DEVICE_ID
wdenka3d991b2004-04-15 21:48:45 +00001623
1624 The device id used in CDP trigger frames.
1625
1626 CONFIG_CDP_DEVICE_ID_PREFIX
1627
1628 A two character string which is prefixed to the MAC address
1629 of the device.
1630
1631 CONFIG_CDP_PORT_ID
1632
1633 A printf format string which contains the ascii name of
1634 the port. Normally is set to "eth%d" which sets
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02001635 eth0 for the first Ethernet, eth1 for the second etc.
wdenka3d991b2004-04-15 21:48:45 +00001636
1637 CONFIG_CDP_CAPABILITIES
1638
1639 A 32bit integer which indicates the device capabilities;
1640 0x00000010 for a normal host which does not forwards.
1641
1642 CONFIG_CDP_VERSION
1643
1644 An ascii string containing the version of the software.
1645
1646 CONFIG_CDP_PLATFORM
1647
1648 An ascii string containing the name of the platform.
1649
1650 CONFIG_CDP_TRIGGER
1651
1652 A 32bit integer sent on the trigger.
1653
1654 CONFIG_CDP_POWER_CONSUMPTION
1655
1656 A 16bit integer containing the power consumption of the
1657 device in .1 of milliwatts.
1658
1659 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1660
1661 A byte containing the id of the VLAN.
1662
wdenkc6097192002-11-03 00:24:07 +00001663- Status LED: CONFIG_STATUS_LED
1664
1665 Several configurations allow to display the current
1666 status using a LED. For instance, the LED will blink
1667 fast while running U-Boot code, stop blinking as
1668 soon as a reply to a BOOTP request was received, and
1669 start blinking slow once the Linux kernel is running
1670 (supported by a status LED driver in the Linux
1671 kernel). Defining CONFIG_STATUS_LED enables this
1672 feature in U-Boot.
1673
1674- CAN Support: CONFIG_CAN_DRIVER
1675
1676 Defining CONFIG_CAN_DRIVER enables CAN driver support
1677 on those systems that support this (optional)
1678 feature, like the TQM8xxL modules.
1679
1680- I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1681
wdenkb37c7e52003-06-30 16:24:52 +00001682 These enable I2C serial bus commands. Defining either of
wdenk945af8d2003-07-16 21:53:01 +00001683 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02001684 include the appropriate I2C driver for the selected CPU.
wdenkc6097192002-11-03 00:24:07 +00001685
wdenk945af8d2003-07-16 21:53:01 +00001686 This will allow you to use i2c commands at the u-boot
Jon Loeliger602ad3b2007-06-11 19:03:39 -05001687 command line (as long as you set CONFIG_CMD_I2C in
wdenkb37c7e52003-06-30 16:24:52 +00001688 CONFIG_COMMANDS) and communicate with i2c based realtime
1689 clock chips. See common/cmd_i2c.c for a description of the
wdenk43d96162003-03-06 00:02:04 +00001690 command line interface.
wdenkc6097192002-11-03 00:24:07 +00001691
Ben Warrenbb99ad62006-09-07 16:50:54 -04001692 CONFIG_HARD_I2C selects a hardware I2C controller.
wdenkc6097192002-11-03 00:24:07 +00001693
wdenk945af8d2003-07-16 21:53:01 +00001694 CONFIG_SOFT_I2C configures u-boot to use a software (aka
wdenkb37c7e52003-06-30 16:24:52 +00001695 bit-banging) driver instead of CPM or similar hardware
1696 support for I2C.
wdenkc6097192002-11-03 00:24:07 +00001697
wdenk945af8d2003-07-16 21:53:01 +00001698 There are several other quantities that must also be
wdenkb37c7e52003-06-30 16:24:52 +00001699 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
wdenkc6097192002-11-03 00:24:07 +00001700
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001701 In both cases you will need to define CONFIG_SYS_I2C_SPEED
wdenk945af8d2003-07-16 21:53:01 +00001702 to be the frequency (in Hz) at which you wish your i2c bus
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001703 to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02001704 the CPU's i2c node address).
wdenk945af8d2003-07-16 21:53:01 +00001705
Peter Tyser8d321b82010-04-12 22:28:21 -05001706 Now, the u-boot i2c code for the mpc8xx
Stefan Roesea47a12b2010-04-15 16:07:28 +02001707 (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
Peter Tyser8d321b82010-04-12 22:28:21 -05001708 and so its address should therefore be cleared to 0 (See,
1709 eg, MPC823e User's Manual p.16-473). So, set
1710 CONFIG_SYS_I2C_SLAVE to 0.
wdenkc6097192002-11-03 00:24:07 +00001711
Eric Millbrandt5da71ef2009-09-03 08:09:44 -05001712 CONFIG_SYS_I2C_INIT_MPC5XXX
1713
1714 When a board is reset during an i2c bus transfer
1715 chips might think that the current transfer is still
1716 in progress. Reset the slave devices by sending start
1717 commands until the slave device responds.
1718
wdenk945af8d2003-07-16 21:53:01 +00001719 That's all that's required for CONFIG_HARD_I2C.
wdenkb37c7e52003-06-30 16:24:52 +00001720
1721 If you use the software i2c interface (CONFIG_SOFT_I2C)
1722 then the following macros need to be defined (examples are
1723 from include/configs/lwmon.h):
wdenkc6097192002-11-03 00:24:07 +00001724
1725 I2C_INIT
1726
wdenkb37c7e52003-06-30 16:24:52 +00001727 (Optional). Any commands necessary to enable the I2C
wdenk43d96162003-03-06 00:02:04 +00001728 controller or configure ports.
wdenkc6097192002-11-03 00:24:07 +00001729
wdenkba56f622004-02-06 23:19:44 +00001730 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
wdenkb37c7e52003-06-30 16:24:52 +00001731
wdenkc6097192002-11-03 00:24:07 +00001732 I2C_PORT
1733
wdenk43d96162003-03-06 00:02:04 +00001734 (Only for MPC8260 CPU). The I/O port to use (the code
1735 assumes both bits are on the same port). Valid values
1736 are 0..3 for ports A..D.
wdenkc6097192002-11-03 00:24:07 +00001737
1738 I2C_ACTIVE
1739
1740 The code necessary to make the I2C data line active
1741 (driven). If the data line is open collector, this
1742 define can be null.
1743
wdenkb37c7e52003-06-30 16:24:52 +00001744 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1745
wdenkc6097192002-11-03 00:24:07 +00001746 I2C_TRISTATE
1747
1748 The code necessary to make the I2C data line tri-stated
1749 (inactive). If the data line is open collector, this
1750 define can be null.
1751
wdenkb37c7e52003-06-30 16:24:52 +00001752 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1753
wdenkc6097192002-11-03 00:24:07 +00001754 I2C_READ
1755
1756 Code that returns TRUE if the I2C data line is high,
1757 FALSE if it is low.
1758
wdenkb37c7e52003-06-30 16:24:52 +00001759 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1760
wdenkc6097192002-11-03 00:24:07 +00001761 I2C_SDA(bit)
1762
1763 If <bit> is TRUE, sets the I2C data line high. If it
1764 is FALSE, it clears it (low).
1765
wdenkb37c7e52003-06-30 16:24:52 +00001766 eg: #define I2C_SDA(bit) \
wdenk2535d602003-07-17 23:16:40 +00001767 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
wdenkba56f622004-02-06 23:19:44 +00001768 else immr->im_cpm.cp_pbdat &= ~PB_SDA
wdenkb37c7e52003-06-30 16:24:52 +00001769
wdenkc6097192002-11-03 00:24:07 +00001770 I2C_SCL(bit)
1771
1772 If <bit> is TRUE, sets the I2C clock line high. If it
1773 is FALSE, it clears it (low).
1774
wdenkb37c7e52003-06-30 16:24:52 +00001775 eg: #define I2C_SCL(bit) \
wdenk2535d602003-07-17 23:16:40 +00001776 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
wdenkba56f622004-02-06 23:19:44 +00001777 else immr->im_cpm.cp_pbdat &= ~PB_SCL
wdenkb37c7e52003-06-30 16:24:52 +00001778
wdenkc6097192002-11-03 00:24:07 +00001779 I2C_DELAY
1780
1781 This delay is invoked four times per clock cycle so this
1782 controls the rate of data transfer. The data rate thus
wdenkb37c7e52003-06-30 16:24:52 +00001783 is 1 / (I2C_DELAY * 4). Often defined to be something
wdenk945af8d2003-07-16 21:53:01 +00001784 like:
1785
wdenkb37c7e52003-06-30 16:24:52 +00001786 #define I2C_DELAY udelay(2)
wdenkc6097192002-11-03 00:24:07 +00001787
Mike Frysinger793b5722010-07-21 13:38:02 -04001788 CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
1789
1790 If your arch supports the generic GPIO framework (asm/gpio.h),
1791 then you may alternatively define the two GPIOs that are to be
1792 used as SCL / SDA. Any of the previous I2C_xxx macros will
1793 have GPIO-based defaults assigned to them as appropriate.
1794
1795 You should define these to the GPIO value as given directly to
1796 the generic GPIO functions.
1797
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001798 CONFIG_SYS_I2C_INIT_BOARD
wdenk47cd00f2003-03-06 13:39:27 +00001799
wdenk8bde7f72003-06-27 21:31:46 +00001800 When a board is reset during an i2c bus transfer
1801 chips might think that the current transfer is still
1802 in progress. On some boards it is possible to access
1803 the i2c SCLK line directly, either by using the
1804 processor pin as a GPIO or by having a second pin
1805 connected to the bus. If this option is defined a
1806 custom i2c_init_board() routine in boards/xxx/board.c
1807 is run early in the boot sequence.
wdenk47cd00f2003-03-06 13:39:27 +00001808
Richard Retanubun26a33502010-04-12 15:08:17 -04001809 CONFIG_SYS_I2C_BOARD_LATE_INIT
1810
1811 An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
1812 defined a custom i2c_board_late_init() routine in
1813 boards/xxx/board.c is run AFTER the operations in i2c_init()
1814 is completed. This callpoint can be used to unreset i2c bus
1815 using CPU i2c controller register accesses for CPUs whose i2c
1816 controller provide such a method. It is called at the end of
1817 i2c_init() to allow i2c_init operations to setup the i2c bus
1818 controller on the CPU (e.g. setting bus speed & slave address).
1819
wdenk17ea1172004-06-06 21:51:03 +00001820 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
1821
1822 This option enables configuration of bi_iic_fast[] flags
1823 in u-boot bd_info structure based on u-boot environment
1824 variable "i2cfast". (see also i2cfast)
1825
Ben Warrenbb99ad62006-09-07 16:50:54 -04001826 CONFIG_I2C_MULTI_BUS
1827
1828 This option allows the use of multiple I2C buses, each of which
Wolfgang Denkc0f40852011-10-26 10:21:21 +00001829 must have a controller. At any point in time, only one bus is
1830 active. To switch to a different bus, use the 'i2c dev' command.
Ben Warrenbb99ad62006-09-07 16:50:54 -04001831 Note that bus numbering is zero-based.
1832
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001833 CONFIG_SYS_I2C_NOPROBES
Ben Warrenbb99ad62006-09-07 16:50:54 -04001834
1835 This option specifies a list of I2C devices that will be skipped
Wolfgang Denkc0f40852011-10-26 10:21:21 +00001836 when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
Peter Tyser0f89c542009-04-18 22:34:03 -05001837 is set, specify a list of bus-device pairs. Otherwise, specify
1838 a 1D array of device addresses
Ben Warrenbb99ad62006-09-07 16:50:54 -04001839
1840 e.g.
1841 #undef CONFIG_I2C_MULTI_BUS
Wolfgang Denkc0f40852011-10-26 10:21:21 +00001842 #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
Ben Warrenbb99ad62006-09-07 16:50:54 -04001843
1844 will skip addresses 0x50 and 0x68 on a board with one I2C bus
1845
Wolfgang Denkc0f40852011-10-26 10:21:21 +00001846 #define CONFIG_I2C_MULTI_BUS
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001847 #define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
Ben Warrenbb99ad62006-09-07 16:50:54 -04001848
1849 will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
1850
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001851 CONFIG_SYS_SPD_BUS_NUM
Timur Tabibe5e6182006-11-03 19:15:00 -06001852
1853 If defined, then this indicates the I2C bus number for DDR SPD.
1854 If not defined, then U-Boot assumes that SPD is on I2C bus 0.
1855
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001856 CONFIG_SYS_RTC_BUS_NUM
Stefan Roese0dc018e2007-02-20 10:51:26 +01001857
1858 If defined, then this indicates the I2C bus number for the RTC.
1859 If not defined, then U-Boot assumes that RTC is on I2C bus 0.
1860
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001861 CONFIG_SYS_DTT_BUS_NUM
Stefan Roese0dc018e2007-02-20 10:51:26 +01001862
1863 If defined, then this indicates the I2C bus number for the DTT.
1864 If not defined, then U-Boot assumes that DTT is on I2C bus 0.
1865
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001866 CONFIG_SYS_I2C_DTT_ADDR:
Victor Gallardo9ebbb542008-09-09 15:13:29 -07001867
1868 If defined, specifies the I2C address of the DTT device.
1869 If not defined, then U-Boot uses predefined value for
1870 specified DTT device.
1871
Timur Tabibe5e6182006-11-03 19:15:00 -06001872 CONFIG_FSL_I2C
1873
1874 Define this option if you want to use Freescale's I2C driver in
Marcel Ziswiler7817cb22007-12-30 03:30:46 +01001875 drivers/i2c/fsl_i2c.c.
Timur Tabibe5e6182006-11-03 19:15:00 -06001876
Heiko Schocher67b23a32008-10-15 09:39:47 +02001877 CONFIG_I2C_MUX
1878
1879 Define this option if you have I2C devices reached over 1 .. n
1880 I2C Muxes like the pca9544a. This option addes a new I2C
1881 Command "i2c bus [muxtype:muxaddr:muxchannel]" which adds a
1882 new I2C Bus to the existing I2C Busses. If you select the
1883 new Bus with "i2c dev", u-bbot sends first the commandos for
1884 the muxes to activate this new "bus".
1885
1886 CONFIG_I2C_MULTI_BUS must be also defined, to use this
1887 feature!
1888
1889 Example:
1890 Adding a new I2C Bus reached over 2 pca9544a muxes
1891 The First mux with address 70 and channel 6
1892 The Second mux with address 71 and channel 4
1893
1894 => i2c bus pca9544a:70:6:pca9544a:71:4
1895
1896 Use the "i2c bus" command without parameter, to get a list
1897 of I2C Busses with muxes:
1898
1899 => i2c bus
1900 Busses reached over muxes:
1901 Bus ID: 2
1902 reached over Mux(es):
1903 pca9544a@70 ch: 4
1904 Bus ID: 3
1905 reached over Mux(es):
1906 pca9544a@70 ch: 6
1907 pca9544a@71 ch: 4
1908 =>
1909
1910 If you now switch to the new I2C Bus 3 with "i2c dev 3"
Michael Jonesf9a78b82011-07-14 22:09:28 +00001911 u-boot first sends the command to the mux@70 to enable
1912 channel 6, and then the command to the mux@71 to enable
Heiko Schocher67b23a32008-10-15 09:39:47 +02001913 the channel 4.
1914
1915 After that, you can use the "normal" i2c commands as
Michael Jonesf9a78b82011-07-14 22:09:28 +00001916 usual to communicate with your I2C devices behind
Heiko Schocher67b23a32008-10-15 09:39:47 +02001917 the 2 muxes.
1918
1919 This option is actually implemented for the bitbanging
1920 algorithm in common/soft_i2c.c and for the Hardware I2C
1921 Bus on the MPC8260. But it should be not so difficult
1922 to add this option to other architectures.
1923
Andrew Dyer2ac69852008-12-29 17:36:01 -06001924 CONFIG_SOFT_I2C_READ_REPEATED_START
1925
1926 defining this will force the i2c_read() function in
1927 the soft_i2c driver to perform an I2C repeated start
1928 between writing the address pointer and reading the
1929 data. If this define is omitted the default behaviour
1930 of doing a stop-start sequence will be used. Most I2C
1931 devices can use either method, but some require one or
1932 the other.
Timur Tabibe5e6182006-11-03 19:15:00 -06001933
wdenkc6097192002-11-03 00:24:07 +00001934- SPI Support: CONFIG_SPI
1935
1936 Enables SPI driver (so far only tested with
1937 SPI EEPROM, also an instance works with Crystal A/D and
1938 D/As on the SACSng board)
1939
Yoshihiro Shimoda66395622011-01-31 16:50:43 +09001940 CONFIG_SH_SPI
1941
1942 Enables the driver for SPI controller on SuperH. Currently
1943 only SH7757 is supported.
1944
wdenkc6097192002-11-03 00:24:07 +00001945 CONFIG_SPI_X
1946
1947 Enables extended (16-bit) SPI EEPROM addressing.
1948 (symmetrical to CONFIG_I2C_X)
1949
1950 CONFIG_SOFT_SPI
1951
wdenk43d96162003-03-06 00:02:04 +00001952 Enables a software (bit-bang) SPI driver rather than
1953 using hardware support. This is a general purpose
1954 driver that only requires three general I/O port pins
1955 (two outputs, one input) to function. If this is
1956 defined, the board configuration must define several
1957 SPI configuration items (port pins to use, etc). For
1958 an example, see include/configs/sacsng.h.
wdenkc6097192002-11-03 00:24:07 +00001959
Ben Warren04a9e112008-01-16 22:37:35 -05001960 CONFIG_HARD_SPI
1961
1962 Enables a hardware SPI driver for general-purpose reads
1963 and writes. As with CONFIG_SOFT_SPI, the board configuration
1964 must define a list of chip-select function pointers.
Wolfgang Denkc0f40852011-10-26 10:21:21 +00001965 Currently supported on some MPC8xxx processors. For an
Ben Warren04a9e112008-01-16 22:37:35 -05001966 example, see include/configs/mpc8349emds.h.
1967
Guennadi Liakhovetski38254f42008-04-15 14:14:25 +02001968 CONFIG_MXC_SPI
1969
1970 Enables the driver for the SPI controllers on i.MX and MXC
Fabio Estevam2e3cd1c2011-10-28 08:57:46 +00001971 SoCs. Currently i.MX31/35/51 are supported.
Guennadi Liakhovetski38254f42008-04-15 14:14:25 +02001972
Matthias Fuchs01335022007-12-27 17:12:34 +01001973- FPGA Support: CONFIG_FPGA
1974
1975 Enables FPGA subsystem.
1976
1977 CONFIG_FPGA_<vendor>
1978
1979 Enables support for specific chip vendors.
1980 (ALTERA, XILINX)
1981
1982 CONFIG_FPGA_<family>
1983
1984 Enables support for FPGA family.
1985 (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
1986
1987 CONFIG_FPGA_COUNT
wdenkc6097192002-11-03 00:24:07 +00001988
wdenk43d96162003-03-06 00:02:04 +00001989 Specify the number of FPGA devices to support.
wdenkc6097192002-11-03 00:24:07 +00001990
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001991 CONFIG_SYS_FPGA_PROG_FEEDBACK
wdenkc6097192002-11-03 00:24:07 +00001992
wdenk8bde7f72003-06-27 21:31:46 +00001993 Enable printing of hash marks during FPGA configuration.
wdenkc6097192002-11-03 00:24:07 +00001994
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02001995 CONFIG_SYS_FPGA_CHECK_BUSY
wdenkc6097192002-11-03 00:24:07 +00001996
wdenk43d96162003-03-06 00:02:04 +00001997 Enable checks on FPGA configuration interface busy
1998 status by the configuration function. This option
1999 will require a board or device specific function to
2000 be written.
wdenkc6097192002-11-03 00:24:07 +00002001
2002 CONFIG_FPGA_DELAY
2003
2004 If defined, a function that provides delays in the FPGA
2005 configuration driver.
2006
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002007 CONFIG_SYS_FPGA_CHECK_CTRLC
wdenkc6097192002-11-03 00:24:07 +00002008 Allow Control-C to interrupt FPGA configuration
2009
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002010 CONFIG_SYS_FPGA_CHECK_ERROR
wdenkc6097192002-11-03 00:24:07 +00002011
wdenk43d96162003-03-06 00:02:04 +00002012 Check for configuration errors during FPGA bitfile
2013 loading. For example, abort during Virtex II
2014 configuration if the INIT_B line goes low (which
2015 indicated a CRC error).
wdenkc6097192002-11-03 00:24:07 +00002016
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002017 CONFIG_SYS_FPGA_WAIT_INIT
wdenkc6097192002-11-03 00:24:07 +00002018
wdenk43d96162003-03-06 00:02:04 +00002019 Maximum time to wait for the INIT_B line to deassert
2020 after PROB_B has been deasserted during a Virtex II
2021 FPGA configuration sequence. The default time is 500
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002022 ms.
wdenkc6097192002-11-03 00:24:07 +00002023
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002024 CONFIG_SYS_FPGA_WAIT_BUSY
wdenkc6097192002-11-03 00:24:07 +00002025
wdenk43d96162003-03-06 00:02:04 +00002026 Maximum time to wait for BUSY to deassert during
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002027 Virtex II FPGA configuration. The default is 5 ms.
wdenkc6097192002-11-03 00:24:07 +00002028
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002029 CONFIG_SYS_FPGA_WAIT_CONFIG
wdenkc6097192002-11-03 00:24:07 +00002030
wdenk43d96162003-03-06 00:02:04 +00002031 Time to wait after FPGA configuration. The default is
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002032 200 ms.
wdenkc6097192002-11-03 00:24:07 +00002033
2034- Configuration Management:
2035 CONFIG_IDENT_STRING
2036
wdenk43d96162003-03-06 00:02:04 +00002037 If defined, this string will be added to the U-Boot
2038 version information (U_BOOT_VERSION)
wdenkc6097192002-11-03 00:24:07 +00002039
2040- Vendor Parameter Protection:
2041
wdenk43d96162003-03-06 00:02:04 +00002042 U-Boot considers the values of the environment
2043 variables "serial#" (Board Serial Number) and
wdenk7152b1d2003-09-05 23:19:14 +00002044 "ethaddr" (Ethernet Address) to be parameters that
wdenk43d96162003-03-06 00:02:04 +00002045 are set once by the board vendor / manufacturer, and
2046 protects these variables from casual modification by
2047 the user. Once set, these variables are read-only,
2048 and write or delete attempts are rejected. You can
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002049 change this behaviour:
wdenkc6097192002-11-03 00:24:07 +00002050
2051 If CONFIG_ENV_OVERWRITE is #defined in your config
2052 file, the write protection for vendor parameters is
wdenk47cd00f2003-03-06 13:39:27 +00002053 completely disabled. Anybody can change or delete
wdenkc6097192002-11-03 00:24:07 +00002054 these parameters.
2055
2056 Alternatively, if you #define _both_ CONFIG_ETHADDR
2057 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002058 Ethernet address is installed in the environment,
wdenkc6097192002-11-03 00:24:07 +00002059 which can be changed exactly ONCE by the user. [The
2060 serial# is unaffected by this, i. e. it remains
2061 read-only.]
2062
2063- Protected RAM:
2064 CONFIG_PRAM
2065
2066 Define this variable to enable the reservation of
2067 "protected RAM", i. e. RAM which is not overwritten
2068 by U-Boot. Define CONFIG_PRAM to hold the number of
2069 kB you want to reserve for pRAM. You can overwrite
2070 this default value by defining an environment
2071 variable "pram" to the number of kB you want to
2072 reserve. Note that the board info structure will
2073 still show the full amount of RAM. If pRAM is
2074 reserved, a new environment variable "mem" will
2075 automatically be defined to hold the amount of
2076 remaining RAM in a form that can be passed as boot
2077 argument to Linux, for instance like that:
2078
Wolfgang Denkfe126d82005-11-20 21:40:11 +01002079 setenv bootargs ... mem=\${mem}
wdenkc6097192002-11-03 00:24:07 +00002080 saveenv
2081
2082 This way you can tell Linux not to use this memory,
2083 either, which results in a memory region that will
2084 not be affected by reboots.
2085
2086 *WARNING* If your board configuration uses automatic
2087 detection of the RAM size, you must make sure that
2088 this memory test is non-destructive. So far, the
2089 following board configurations are known to be
2090 "pRAM-clean":
2091
2092 ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
2093 HERMES, IP860, RPXlite, LWMON, LANTEC,
Wolfgang Denk544d97e2010-10-05 22:54:53 +02002094 FLAGADM, TQM8260
wdenkc6097192002-11-03 00:24:07 +00002095
2096- Error Recovery:
2097 CONFIG_PANIC_HANG
2098
2099 Define this variable to stop the system in case of a
2100 fatal error, so that you have to reset it manually.
2101 This is probably NOT a good idea for an embedded
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002102 system where you want the system to reboot
wdenkc6097192002-11-03 00:24:07 +00002103 automatically as fast as possible, but it may be
2104 useful during development since you can try to debug
2105 the conditions that lead to the situation.
2106
2107 CONFIG_NET_RETRY_COUNT
2108
wdenk43d96162003-03-06 00:02:04 +00002109 This variable defines the number of retries for
2110 network operations like ARP, RARP, TFTP, or BOOTP
2111 before giving up the operation. If not defined, a
2112 default value of 5 is used.
wdenkc6097192002-11-03 00:24:07 +00002113
Guennadi Liakhovetski40cb90e2008-04-03 17:04:19 +02002114 CONFIG_ARP_TIMEOUT
2115
2116 Timeout waiting for an ARP reply in milliseconds.
2117
wdenkc6097192002-11-03 00:24:07 +00002118- Command Interpreter:
Wolfgang Denk8078f1a2006-10-28 02:28:02 +02002119 CONFIG_AUTO_COMPLETE
wdenk04a85b32004-04-15 18:22:41 +00002120
2121 Enable auto completion of commands using TAB.
2122
Wolfgang Denka9398e02006-11-27 15:32:42 +01002123 Note that this feature has NOT been implemented yet
2124 for the "hush" shell.
Wolfgang Denk8078f1a2006-10-28 02:28:02 +02002125
2126
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002127 CONFIG_SYS_HUSH_PARSER
wdenkc6097192002-11-03 00:24:07 +00002128
2129 Define this variable to enable the "hush" shell (from
2130 Busybox) as command line interpreter, thus enabling
2131 powerful command line syntax like
2132 if...then...else...fi conditionals or `&&' and '||'
2133 constructs ("shell scripts").
2134
2135 If undefined, you get the old, much simpler behaviour
2136 with a somewhat smaller memory footprint.
2137
2138
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002139 CONFIG_SYS_PROMPT_HUSH_PS2
wdenkc6097192002-11-03 00:24:07 +00002140
2141 This defines the secondary prompt string, which is
2142 printed when the command interpreter needs more input
2143 to complete a command. Usually "> ".
2144
2145 Note:
2146
wdenk8bde7f72003-06-27 21:31:46 +00002147 In the current implementation, the local variables
2148 space and global environment variables space are
2149 separated. Local variables are those you define by
2150 simply typing `name=value'. To access a local
2151 variable later on, you have write `$name' or
2152 `${name}'; to execute the contents of a variable
2153 directly type `$name' at the command prompt.
wdenkc6097192002-11-03 00:24:07 +00002154
wdenk43d96162003-03-06 00:02:04 +00002155 Global environment variables are those you use
2156 setenv/printenv to work with. To run a command stored
2157 in such a variable, you need to use the run command,
2158 and you must not use the '$' sign to access them.
wdenkc6097192002-11-03 00:24:07 +00002159
2160 To store commands and special characters in a
2161 variable, please use double quotation marks
2162 surrounding the whole text of the variable, instead
2163 of the backslashes before semicolons and special
2164 symbols.
2165
Wolfgang Denkaa0c71a2006-07-21 11:35:21 +02002166- Commandline Editing and History:
2167 CONFIG_CMDLINE_EDITING
2168
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002169 Enable editing and History functions for interactive
Wolfgang Denkb9365a22006-07-21 11:56:05 +02002170 commandline input operations
Wolfgang Denkaa0c71a2006-07-21 11:35:21 +02002171
wdenka8c7c702003-12-06 19:49:23 +00002172- Default Environment:
wdenkc6097192002-11-03 00:24:07 +00002173 CONFIG_EXTRA_ENV_SETTINGS
2174
wdenk43d96162003-03-06 00:02:04 +00002175 Define this to contain any number of null terminated
2176 strings (variable = value pairs) that will be part of
wdenk7152b1d2003-09-05 23:19:14 +00002177 the default environment compiled into the boot image.
wdenk2262cfe2002-11-18 00:14:45 +00002178
wdenk43d96162003-03-06 00:02:04 +00002179 For example, place something like this in your
2180 board's config file:
wdenkc6097192002-11-03 00:24:07 +00002181
2182 #define CONFIG_EXTRA_ENV_SETTINGS \
2183 "myvar1=value1\0" \
2184 "myvar2=value2\0"
2185
wdenk43d96162003-03-06 00:02:04 +00002186 Warning: This method is based on knowledge about the
2187 internal format how the environment is stored by the
2188 U-Boot code. This is NOT an official, exported
2189 interface! Although it is unlikely that this format
wdenk7152b1d2003-09-05 23:19:14 +00002190 will change soon, there is no guarantee either.
wdenkc6097192002-11-03 00:24:07 +00002191 You better know what you are doing here.
2192
wdenk43d96162003-03-06 00:02:04 +00002193 Note: overly (ab)use of the default environment is
2194 discouraged. Make sure to check other ways to preset
Wolfgang Denk74de7ae2009-04-01 23:34:12 +02002195 the environment like the "source" command or the
wdenk43d96162003-03-06 00:02:04 +00002196 boot command first.
wdenkc6097192002-11-03 00:24:07 +00002197
wdenka8c7c702003-12-06 19:49:23 +00002198- DataFlash Support:
wdenk2abbe072003-06-16 23:50:08 +00002199 CONFIG_HAS_DATAFLASH
2200
wdenk8bde7f72003-06-27 21:31:46 +00002201 Defining this option enables DataFlash features and
2202 allows to read/write in Dataflash via the standard
2203 commands cp, md...
wdenk2abbe072003-06-16 23:50:08 +00002204
Eric Nelsonf61ec452012-01-31 10:52:08 -07002205- Serial Flash support
2206 CONFIG_CMD_SF
2207
2208 Defining this option enables SPI flash commands
2209 'sf probe/read/write/erase/update'.
2210
2211 Usage requires an initial 'probe' to define the serial
2212 flash parameters, followed by read/write/erase/update
2213 commands.
2214
2215 The following defaults may be provided by the platform
2216 to handle the common case when only a single serial
2217 flash is present on the system.
2218
2219 CONFIG_SF_DEFAULT_BUS Bus identifier
2220 CONFIG_SF_DEFAULT_CS Chip-select
2221 CONFIG_SF_DEFAULT_MODE (see include/spi.h)
2222 CONFIG_SF_DEFAULT_SPEED in Hz
2223
wdenk3f85ce22004-02-23 16:11:30 +00002224- SystemACE Support:
2225 CONFIG_SYSTEMACE
2226
2227 Adding this option adds support for Xilinx SystemACE
2228 chips attached via some sort of local bus. The address
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002229 of the chip must also be defined in the
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002230 CONFIG_SYS_SYSTEMACE_BASE macro. For example:
wdenk3f85ce22004-02-23 16:11:30 +00002231
2232 #define CONFIG_SYSTEMACE
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002233 #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
wdenk3f85ce22004-02-23 16:11:30 +00002234
2235 When SystemACE support is added, the "ace" device type
2236 becomes available to the fat commands, i.e. fatls.
2237
Wolfgang Denkecb0ccd2005-09-24 22:37:32 +02002238- TFTP Fixed UDP Port:
2239 CONFIG_TFTP_PORT
2240
Wolfgang Denk28cb9372005-09-24 23:25:46 +02002241 If this is defined, the environment variable tftpsrcp
Wolfgang Denkecb0ccd2005-09-24 22:37:32 +02002242 is used to supply the TFTP UDP source port value.
Wolfgang Denk28cb9372005-09-24 23:25:46 +02002243 If tftpsrcp isn't defined, the normal pseudo-random port
Wolfgang Denkecb0ccd2005-09-24 22:37:32 +02002244 number generator is used.
2245
Wolfgang Denk28cb9372005-09-24 23:25:46 +02002246 Also, the environment variable tftpdstp is used to supply
2247 the TFTP UDP destination port value. If tftpdstp isn't
2248 defined, the normal port 69 is used.
2249
2250 The purpose for tftpsrcp is to allow a TFTP server to
Wolfgang Denkecb0ccd2005-09-24 22:37:32 +02002251 blindly start the TFTP transfer using the pre-configured
2252 target IP address and UDP port. This has the effect of
2253 "punching through" the (Windows XP) firewall, allowing
2254 the remainder of the TFTP transfer to proceed normally.
2255 A better solution is to properly configure the firewall,
2256 but sometimes that is not allowed.
2257
wdenka8c7c702003-12-06 19:49:23 +00002258- Show boot progress:
wdenkc6097192002-11-03 00:24:07 +00002259 CONFIG_SHOW_BOOT_PROGRESS
2260
wdenk43d96162003-03-06 00:02:04 +00002261 Defining this option allows to add some board-
2262 specific code (calling a user-provided function
2263 "show_boot_progress(int)") that enables you to show
2264 the system's boot progress on some display (for
2265 example, some LED's) on your board. At the moment,
2266 the following checkpoints are implemented:
wdenkc6097192002-11-03 00:24:07 +00002267
Simon Glass3a608ca2012-02-13 13:51:19 +00002268- Detailed boot stage timing
2269 CONFIG_BOOTSTAGE
2270 Define this option to get detailed timing of each stage
2271 of the boot process.
2272
2273 CONFIG_BOOTSTAGE_USER_COUNT
2274 This is the number of available user bootstage records.
2275 Each time you call bootstage_mark(BOOTSTAGE_ID_ALLOC, ...)
2276 a new ID will be allocated from this stash. If you exceed
2277 the limit, recording will stop.
2278
2279 CONFIG_BOOTSTAGE_REPORT
2280 Define this to print a report before boot, similar to this:
2281
2282 Timer summary in microseconds:
2283 Mark Elapsed Stage
2284 0 0 reset
2285 3,575,678 3,575,678 board_init_f start
2286 3,575,695 17 arch_cpu_init A9
2287 3,575,777 82 arch_cpu_init done
2288 3,659,598 83,821 board_init_r start
2289 3,910,375 250,777 main_loop
2290 29,916,167 26,005,792 bootm_start
2291 30,361,327 445,160 start_kernel
2292
Marian Balakowicz1372cce2008-03-12 10:33:01 +01002293Legacy uImage format:
2294
wdenkc6097192002-11-03 00:24:07 +00002295 Arg Where When
2296 1 common/cmd_bootm.c before attempting to boot an image
wdenkba56f622004-02-06 23:19:44 +00002297 -1 common/cmd_bootm.c Image header has bad magic number
wdenkc6097192002-11-03 00:24:07 +00002298 2 common/cmd_bootm.c Image header has correct magic number
wdenkba56f622004-02-06 23:19:44 +00002299 -2 common/cmd_bootm.c Image header has bad checksum
wdenkc6097192002-11-03 00:24:07 +00002300 3 common/cmd_bootm.c Image header has correct checksum
wdenkba56f622004-02-06 23:19:44 +00002301 -3 common/cmd_bootm.c Image data has bad checksum
wdenkc6097192002-11-03 00:24:07 +00002302 4 common/cmd_bootm.c Image data has correct checksum
2303 -4 common/cmd_bootm.c Image is for unsupported architecture
2304 5 common/cmd_bootm.c Architecture check OK
Marian Balakowicz1372cce2008-03-12 10:33:01 +01002305 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
wdenkc6097192002-11-03 00:24:07 +00002306 6 common/cmd_bootm.c Image Type check OK
2307 -6 common/cmd_bootm.c gunzip uncompression error
2308 -7 common/cmd_bootm.c Unimplemented compression type
2309 7 common/cmd_bootm.c Uncompression OK
Marian Balakowicz1372cce2008-03-12 10:33:01 +01002310 8 common/cmd_bootm.c No uncompress/copy overwrite error
wdenkc6097192002-11-03 00:24:07 +00002311 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
Marian Balakowicz1372cce2008-03-12 10:33:01 +01002312
2313 9 common/image.c Start initial ramdisk verification
2314 -10 common/image.c Ramdisk header has bad magic number
2315 -11 common/image.c Ramdisk header has bad checksum
2316 10 common/image.c Ramdisk header is OK
2317 -12 common/image.c Ramdisk data has bad checksum
2318 11 common/image.c Ramdisk data has correct checksum
2319 12 common/image.c Ramdisk verification complete, start loading
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002320 -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
Marian Balakowicz1372cce2008-03-12 10:33:01 +01002321 13 common/image.c Start multifile image verification
2322 14 common/image.c No initial ramdisk, no multifile, continue.
2323
Wolfgang Denkc0f40852011-10-26 10:21:21 +00002324 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
wdenkc6097192002-11-03 00:24:07 +00002325
Stefan Roesea47a12b2010-04-15 16:07:28 +02002326 -30 arch/powerpc/lib/board.c Fatal error, hang the system
wdenk11dadd52004-02-27 00:07:27 +00002327 -31 post/post.c POST test failed, detected by post_output_backlog()
2328 -32 post/post.c POST test failed, detected by post_run_single()
wdenk63e73c92004-02-23 22:22:28 +00002329
Heiko Schocher566a4942007-06-22 19:11:54 +02002330 34 common/cmd_doc.c before loading a Image from a DOC device
2331 -35 common/cmd_doc.c Bad usage of "doc" command
2332 35 common/cmd_doc.c correct usage of "doc" command
2333 -36 common/cmd_doc.c No boot device
2334 36 common/cmd_doc.c correct boot device
2335 -37 common/cmd_doc.c Unknown Chip ID on boot device
2336 37 common/cmd_doc.c correct chip ID found, device available
2337 -38 common/cmd_doc.c Read Error on boot device
2338 38 common/cmd_doc.c reading Image header from DOC device OK
2339 -39 common/cmd_doc.c Image header has bad magic number
2340 39 common/cmd_doc.c Image header has correct magic number
2341 -40 common/cmd_doc.c Error reading Image from DOC device
2342 40 common/cmd_doc.c Image header has correct magic number
2343 41 common/cmd_ide.c before loading a Image from a IDE device
2344 -42 common/cmd_ide.c Bad usage of "ide" command
2345 42 common/cmd_ide.c correct usage of "ide" command
2346 -43 common/cmd_ide.c No boot device
2347 43 common/cmd_ide.c boot device found
2348 -44 common/cmd_ide.c Device not available
2349 44 common/cmd_ide.c Device available
2350 -45 common/cmd_ide.c wrong partition selected
2351 45 common/cmd_ide.c partition selected
2352 -46 common/cmd_ide.c Unknown partition table
2353 46 common/cmd_ide.c valid partition table found
2354 -47 common/cmd_ide.c Invalid partition type
2355 47 common/cmd_ide.c correct partition type
2356 -48 common/cmd_ide.c Error reading Image Header on boot device
2357 48 common/cmd_ide.c reading Image Header from IDE device OK
2358 -49 common/cmd_ide.c Image header has bad magic number
2359 49 common/cmd_ide.c Image header has correct magic number
2360 -50 common/cmd_ide.c Image header has bad checksum
2361 50 common/cmd_ide.c Image header has correct checksum
2362 -51 common/cmd_ide.c Error reading Image from IDE device
2363 51 common/cmd_ide.c reading Image from IDE device OK
2364 52 common/cmd_nand.c before loading a Image from a NAND device
2365 -53 common/cmd_nand.c Bad usage of "nand" command
2366 53 common/cmd_nand.c correct usage of "nand" command
2367 -54 common/cmd_nand.c No boot device
2368 54 common/cmd_nand.c boot device found
2369 -55 common/cmd_nand.c Unknown Chip ID on boot device
2370 55 common/cmd_nand.c correct chip ID found, device available
2371 -56 common/cmd_nand.c Error reading Image Header on boot device
2372 56 common/cmd_nand.c reading Image Header from NAND device OK
2373 -57 common/cmd_nand.c Image header has bad magic number
2374 57 common/cmd_nand.c Image header has correct magic number
2375 -58 common/cmd_nand.c Error reading Image from NAND device
2376 58 common/cmd_nand.c reading Image from NAND device OK
wdenkc6097192002-11-03 00:24:07 +00002377
Heiko Schocher566a4942007-06-22 19:11:54 +02002378 -60 common/env_common.c Environment has a bad CRC, using default
wdenkc6097192002-11-03 00:24:07 +00002379
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002380 64 net/eth.c starting with Ethernet configuration.
Heiko Schocher566a4942007-06-22 19:11:54 +02002381 -64 net/eth.c no Ethernet found.
2382 65 net/eth.c Ethernet found.
wdenk206c60c2003-09-18 10:02:25 +00002383
Heiko Schocher566a4942007-06-22 19:11:54 +02002384 -80 common/cmd_net.c usage wrong
2385 80 common/cmd_net.c before calling NetLoop()
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002386 -81 common/cmd_net.c some error in NetLoop() occurred
Heiko Schocher566a4942007-06-22 19:11:54 +02002387 81 common/cmd_net.c NetLoop() back without error
2388 -82 common/cmd_net.c size == 0 (File with size 0 loaded)
2389 82 common/cmd_net.c trying automatic boot
Wolfgang Denk74de7ae2009-04-01 23:34:12 +02002390 83 common/cmd_net.c running "source" command
2391 -83 common/cmd_net.c some error in automatic boot or "source" command
Heiko Schocher566a4942007-06-22 19:11:54 +02002392 84 common/cmd_net.c end without errors
wdenkc6097192002-11-03 00:24:07 +00002393
Marian Balakowicz1372cce2008-03-12 10:33:01 +01002394FIT uImage format:
2395
2396 Arg Where When
2397 100 common/cmd_bootm.c Kernel FIT Image has correct format
2398 -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
2399 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
2400 -101 common/cmd_bootm.c Can't get configuration for kernel subimage
2401 102 common/cmd_bootm.c Kernel unit name specified
2402 -103 common/cmd_bootm.c Can't get kernel subimage node offset
Marian Balakowiczf773bea2008-03-12 10:35:46 +01002403 103 common/cmd_bootm.c Found configuration node
Marian Balakowicz1372cce2008-03-12 10:33:01 +01002404 104 common/cmd_bootm.c Got kernel subimage node offset
2405 -104 common/cmd_bootm.c Kernel subimage hash verification failed
2406 105 common/cmd_bootm.c Kernel subimage hash verification OK
2407 -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
2408 106 common/cmd_bootm.c Architecture check OK
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002409 -106 common/cmd_bootm.c Kernel subimage has wrong type
2410 107 common/cmd_bootm.c Kernel subimage type OK
Marian Balakowicz1372cce2008-03-12 10:33:01 +01002411 -107 common/cmd_bootm.c Can't get kernel subimage data/size
2412 108 common/cmd_bootm.c Got kernel subimage data/size
2413 -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
2414 -109 common/cmd_bootm.c Can't get kernel subimage type
2415 -110 common/cmd_bootm.c Can't get kernel subimage comp
2416 -111 common/cmd_bootm.c Can't get kernel subimage os
2417 -112 common/cmd_bootm.c Can't get kernel subimage load address
2418 -113 common/cmd_bootm.c Image uncompress/copy overwrite error
2419
2420 120 common/image.c Start initial ramdisk verification
2421 -120 common/image.c Ramdisk FIT image has incorrect format
2422 121 common/image.c Ramdisk FIT image has correct format
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002423 122 common/image.c No ramdisk subimage unit name, using configuration
Marian Balakowicz1372cce2008-03-12 10:33:01 +01002424 -122 common/image.c Can't get configuration for ramdisk subimage
2425 123 common/image.c Ramdisk unit name specified
2426 -124 common/image.c Can't get ramdisk subimage node offset
2427 125 common/image.c Got ramdisk subimage node offset
2428 -125 common/image.c Ramdisk subimage hash verification failed
2429 126 common/image.c Ramdisk subimage hash verification OK
2430 -126 common/image.c Ramdisk subimage for unsupported architecture
2431 127 common/image.c Architecture check OK
2432 -127 common/image.c Can't get ramdisk subimage data/size
2433 128 common/image.c Got ramdisk subimage data/size
2434 129 common/image.c Can't get ramdisk load address
2435 -129 common/image.c Got ramdisk load address
2436
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002437 -130 common/cmd_doc.c Incorrect FIT image format
Marian Balakowicz1372cce2008-03-12 10:33:01 +01002438 131 common/cmd_doc.c FIT image format OK
2439
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002440 -140 common/cmd_ide.c Incorrect FIT image format
Marian Balakowicz1372cce2008-03-12 10:33:01 +01002441 141 common/cmd_ide.c FIT image format OK
2442
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002443 -150 common/cmd_nand.c Incorrect FIT image format
Marian Balakowicz1372cce2008-03-12 10:33:01 +01002444 151 common/cmd_nand.c FIT image format OK
2445
Wolfgang Denk4cf26092011-10-07 09:58:21 +02002446- Standalone program support:
2447 CONFIG_STANDALONE_LOAD_ADDR
2448
Wolfgang Denk6feff892011-10-09 21:06:34 +02002449 This option defines a board specific value for the
2450 address where standalone program gets loaded, thus
2451 overwriting the architecture dependent default
Wolfgang Denk4cf26092011-10-07 09:58:21 +02002452 settings.
2453
2454- Frame Buffer Address:
2455 CONFIG_FB_ADDR
2456
2457 Define CONFIG_FB_ADDR if you want to use specific
2458 address for frame buffer.
2459 Then system will reserve the frame buffer address to
2460 defined address instead of lcd_setmem (this function
Wolfgang Denk6feff892011-10-09 21:06:34 +02002461 grabs the memory for frame buffer by panel's size).
Wolfgang Denk4cf26092011-10-07 09:58:21 +02002462
2463 Please see board_init_f function.
2464
Detlev Zundelcccfc2a2009-12-01 17:16:19 +01002465- Automatic software updates via TFTP server
2466 CONFIG_UPDATE_TFTP
2467 CONFIG_UPDATE_TFTP_CNT_MAX
2468 CONFIG_UPDATE_TFTP_MSEC_MAX
2469
2470 These options enable and control the auto-update feature;
2471 for a more detailed description refer to doc/README.update.
2472
2473- MTD Support (mtdparts command, UBI support)
2474 CONFIG_MTD_DEVICE
2475
2476 Adds the MTD device infrastructure from the Linux kernel.
2477 Needed for mtdparts command support.
2478
2479 CONFIG_MTD_PARTITIONS
2480
2481 Adds the MTD partitioning infrastructure from the Linux
2482 kernel. Needed for UBI support.
2483
Daniel Schwierzeck6a11cf42011-07-18 07:48:07 +00002484- SPL framework
Wolfgang Denk04e5ae72011-09-11 21:24:09 +02002485 CONFIG_SPL
2486 Enable building of SPL globally.
Daniel Schwierzeck6a11cf42011-07-18 07:48:07 +00002487
Tom Rini95579792012-02-14 07:29:40 +00002488 CONFIG_SPL_LDSCRIPT
2489 LDSCRIPT for linking the SPL binary.
2490
2491 CONFIG_SPL_MAX_SIZE
2492 Maximum binary size (text, data and rodata) of the SPL binary.
2493
Wolfgang Denk04e5ae72011-09-11 21:24:09 +02002494 CONFIG_SPL_TEXT_BASE
2495 TEXT_BASE for linking the SPL binary.
Daniel Schwierzeck6a11cf42011-07-18 07:48:07 +00002496
Tom Rini95579792012-02-14 07:29:40 +00002497 CONFIG_SPL_BSS_START_ADDR
2498 Link address for the BSS within the SPL binary.
2499
2500 CONFIG_SPL_BSS_MAX_SIZE
2501 Maximum binary size of the BSS section of the SPL binary.
2502
2503 CONFIG_SPL_STACK
2504 Adress of the start of the stack SPL will use
2505
2506 CONFIG_SYS_SPL_MALLOC_START
2507 Starting address of the malloc pool used in SPL.
2508
2509 CONFIG_SYS_SPL_MALLOC_SIZE
2510 The size of the malloc pool used in SPL.
Daniel Schwierzeck6a11cf42011-07-18 07:48:07 +00002511
Wolfgang Denk04e5ae72011-09-11 21:24:09 +02002512 CONFIG_SPL_LIBCOMMON_SUPPORT
2513 Support for common/libcommon.o in SPL binary
Daniel Schwierzeck6a11cf42011-07-18 07:48:07 +00002514
Wolfgang Denk04e5ae72011-09-11 21:24:09 +02002515 CONFIG_SPL_LIBDISK_SUPPORT
2516 Support for disk/libdisk.o in SPL binary
Daniel Schwierzeck6a11cf42011-07-18 07:48:07 +00002517
Wolfgang Denk04e5ae72011-09-11 21:24:09 +02002518 CONFIG_SPL_I2C_SUPPORT
2519 Support for drivers/i2c/libi2c.o in SPL binary
Daniel Schwierzeck6a11cf42011-07-18 07:48:07 +00002520
Wolfgang Denk04e5ae72011-09-11 21:24:09 +02002521 CONFIG_SPL_GPIO_SUPPORT
2522 Support for drivers/gpio/libgpio.o in SPL binary
Daniel Schwierzeck6a11cf42011-07-18 07:48:07 +00002523
Wolfgang Denk04e5ae72011-09-11 21:24:09 +02002524 CONFIG_SPL_MMC_SUPPORT
2525 Support for drivers/mmc/libmmc.o in SPL binary
Daniel Schwierzeck6a11cf42011-07-18 07:48:07 +00002526
Tom Rini95579792012-02-14 07:29:40 +00002527 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR,
2528 CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS,
2529 CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION
2530 Address, size and partition on the MMC to load U-Boot from
2531 when the MMC is being used in raw mode.
2532
2533 CONFIG_SPL_FAT_SUPPORT
2534 Support for fs/fat/libfat.o in SPL binary
2535
2536 CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME
2537 Filename to read to load U-Boot when reading from FAT
2538
2539 CONFIG_SPL_NAND_SIMPLE
2540 Support for drivers/mtd/nand/libnand.o in SPL binary
2541
2542 CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
2543 CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
2544 CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
2545 CONFIG_SYS_NAND_ECCPOS, CONFIG_SYS_NAND_ECCSIZE,
2546 CONFIG_SYS_NAND_ECCBYTES
2547 Defines the size and behavior of the NAND that SPL uses
2548 to read U-Boot with CONFIG_SPL_NAND_SIMPLE
2549
2550 CONFIG_SYS_NAND_U_BOOT_OFFS
2551 Location in NAND for CONFIG_SPL_NAND_SIMPLE to read U-Boot
2552 from.
2553
2554 CONFIG_SYS_NAND_U_BOOT_START
2555 Location in memory for CONFIG_SPL_NAND_SIMPLE to load U-Boot
2556 to.
2557
2558 CONFIG_SYS_NAND_HW_ECC_OOBFIRST
2559 Define this if you need to first read the OOB and then the
2560 data. This is used for example on davinci plattforms.
2561
2562 CONFIG_SPL_OMAP3_ID_NAND
2563 Support for an OMAP3-specific set of functions to return the
2564 ID and MFR of the first attached NAND chip, if present.
2565
Wolfgang Denk04e5ae72011-09-11 21:24:09 +02002566 CONFIG_SPL_SERIAL_SUPPORT
2567 Support for drivers/serial/libserial.o in SPL binary
Daniel Schwierzeck6a11cf42011-07-18 07:48:07 +00002568
Wolfgang Denk04e5ae72011-09-11 21:24:09 +02002569 CONFIG_SPL_SPI_FLASH_SUPPORT
2570 Support for drivers/mtd/spi/libspi_flash.o in SPL binary
Daniel Schwierzeck6a11cf42011-07-18 07:48:07 +00002571
Wolfgang Denk04e5ae72011-09-11 21:24:09 +02002572 CONFIG_SPL_SPI_SUPPORT
2573 Support for drivers/spi/libspi.o in SPL binary
Daniel Schwierzeck6a11cf42011-07-18 07:48:07 +00002574
Wolfgang Denk04e5ae72011-09-11 21:24:09 +02002575 CONFIG_SPL_LIBGENERIC_SUPPORT
2576 Support for lib/libgeneric.o in SPL binary
Marian Balakowicz1372cce2008-03-12 10:33:01 +01002577
wdenkc6097192002-11-03 00:24:07 +00002578Modem Support:
2579--------------
2580
Wolfgang Denk566e5cf2011-05-01 20:44:23 +02002581[so far only for SMDK2400 boards]
wdenkc6097192002-11-03 00:24:07 +00002582
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002583- Modem support enable:
wdenkc6097192002-11-03 00:24:07 +00002584 CONFIG_MODEM_SUPPORT
2585
2586- RTS/CTS Flow control enable:
2587 CONFIG_HWFLOW
2588
2589- Modem debug support:
2590 CONFIG_MODEM_SUPPORT_DEBUG
2591
wdenk43d96162003-03-06 00:02:04 +00002592 Enables debugging stuff (char screen[1024], dbg())
2593 for modem support. Useful only with BDI2000.
wdenkc6097192002-11-03 00:24:07 +00002594
wdenka8c7c702003-12-06 19:49:23 +00002595- Interrupt support (PPC):
2596
wdenkd4ca31c2004-01-02 14:00:00 +00002597 There are common interrupt_init() and timer_interrupt()
2598 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002599 for CPU specific initialization. interrupt_init_cpu()
wdenkd4ca31c2004-01-02 14:00:00 +00002600 should set decrementer_count to appropriate value. If
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002601 CPU resets decrementer automatically after interrupt
wdenkd4ca31c2004-01-02 14:00:00 +00002602 (ppc4xx) it should set decrementer_count to zero.
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002603 timer_interrupt() calls timer_interrupt_cpu() for CPU
wdenkd4ca31c2004-01-02 14:00:00 +00002604 specific handling. If board has watchdog / status_led
2605 / other_activity_monitor it works automatically from
2606 general timer_interrupt().
wdenka8c7c702003-12-06 19:49:23 +00002607
wdenkc6097192002-11-03 00:24:07 +00002608- General:
2609
wdenk43d96162003-03-06 00:02:04 +00002610 In the target system modem support is enabled when a
2611 specific key (key combination) is pressed during
2612 power-on. Otherwise U-Boot will boot normally
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002613 (autoboot). The key_pressed() function is called from
wdenk43d96162003-03-06 00:02:04 +00002614 board_init(). Currently key_pressed() is a dummy
2615 function, returning 1 and thus enabling modem
2616 initialization.
wdenkc6097192002-11-03 00:24:07 +00002617
wdenk43d96162003-03-06 00:02:04 +00002618 If there are no modem init strings in the
2619 environment, U-Boot proceed to autoboot; the
2620 previous output (banner, info printfs) will be
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002621 suppressed, though.
wdenkc6097192002-11-03 00:24:07 +00002622
2623 See also: doc/README.Modem
2624
Helmut Raiger9660e442011-10-20 04:19:47 +00002625Board initialization settings:
2626------------------------------
2627
2628During Initialization u-boot calls a number of board specific functions
2629to allow the preparation of board specific prerequisites, e.g. pin setup
2630before drivers are initialized. To enable these callbacks the
2631following configuration macros have to be defined. Currently this is
2632architecture specific, so please check arch/your_architecture/lib/board.c
2633typically in board_init_f() and board_init_r().
2634
2635- CONFIG_BOARD_EARLY_INIT_F: Call board_early_init_f()
2636- CONFIG_BOARD_EARLY_INIT_R: Call board_early_init_r()
2637- CONFIG_BOARD_LATE_INIT: Call board_late_init()
2638- CONFIG_BOARD_POSTCLK_INIT: Call board_postclk_init()
wdenkc6097192002-11-03 00:24:07 +00002639
wdenkc6097192002-11-03 00:24:07 +00002640Configuration Settings:
2641-----------------------
2642
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002643- CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
wdenkc6097192002-11-03 00:24:07 +00002644 undefine this when you're short of memory.
2645
Peter Tyser2fb26042009-01-27 18:03:12 -06002646- CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
2647 width of the commands listed in the 'help' command output.
2648
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002649- CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to
wdenkc6097192002-11-03 00:24:07 +00002650 prompt for user input.
2651
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002652- CONFIG_SYS_CBSIZE: Buffer size for input from the Console
wdenkc6097192002-11-03 00:24:07 +00002653
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002654- CONFIG_SYS_PBSIZE: Buffer size for Console output
wdenkc6097192002-11-03 00:24:07 +00002655
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002656- CONFIG_SYS_MAXARGS: max. Number of arguments accepted for monitor commands
wdenkc6097192002-11-03 00:24:07 +00002657
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002658- CONFIG_SYS_BARGSIZE: Buffer size for Boot Arguments which are passed to
wdenkc6097192002-11-03 00:24:07 +00002659 the application (usually a Linux kernel) when it is
2660 booted
2661
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002662- CONFIG_SYS_BAUDRATE_TABLE:
wdenkc6097192002-11-03 00:24:07 +00002663 List of legal baudrate settings for this board.
2664
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002665- CONFIG_SYS_CONSOLE_INFO_QUIET
wdenk8bde7f72003-06-27 21:31:46 +00002666 Suppress display of console information at boot.
wdenkc6097192002-11-03 00:24:07 +00002667
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002668- CONFIG_SYS_CONSOLE_IS_IN_ENV
wdenk8bde7f72003-06-27 21:31:46 +00002669 If the board specific function
2670 extern int overwrite_console (void);
2671 returns 1, the stdin, stderr and stdout are switched to the
wdenkc6097192002-11-03 00:24:07 +00002672 serial port, else the settings in the environment are used.
2673
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002674- CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
wdenk8bde7f72003-06-27 21:31:46 +00002675 Enable the call to overwrite_console().
wdenkc6097192002-11-03 00:24:07 +00002676
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002677- CONFIG_SYS_CONSOLE_ENV_OVERWRITE
wdenkc6097192002-11-03 00:24:07 +00002678 Enable overwrite of previous console environment settings.
2679
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002680- CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
wdenkc6097192002-11-03 00:24:07 +00002681 Begin and End addresses of the area used by the
2682 simple memory test.
2683
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002684- CONFIG_SYS_ALT_MEMTEST:
wdenk8bde7f72003-06-27 21:31:46 +00002685 Enable an alternate, more extensive memory test.
wdenkc6097192002-11-03 00:24:07 +00002686
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002687- CONFIG_SYS_MEMTEST_SCRATCH:
wdenk5f535fe2003-09-18 09:21:33 +00002688 Scratch address used by the alternate memory test
2689 You only need to set this if address zero isn't writeable
2690
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002691- CONFIG_SYS_MEM_TOP_HIDE (PPC only):
2692 If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
Stefan Roese14f73ca2008-03-26 10:14:11 +01002693 this specified memory area will get subtracted from the top
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002694 (end) of RAM and won't get "touched" at all by U-Boot. By
Stefan Roese14f73ca2008-03-26 10:14:11 +01002695 fixing up gd->ram_size the Linux kernel should gets passed
2696 the now "corrected" memory size and won't touch it either.
2697 This should work for arch/ppc and arch/powerpc. Only Linux
Stefan Roese5e12e752008-03-28 11:02:53 +01002698 board ports in arch/powerpc with bootwrapper support that
Stefan Roese14f73ca2008-03-26 10:14:11 +01002699 recalculate the memory size from the SDRAM controller setup
Stefan Roese5e12e752008-03-28 11:02:53 +01002700 will have to get fixed in Linux additionally.
Stefan Roese14f73ca2008-03-26 10:14:11 +01002701
2702 This option can be used as a workaround for the 440EPx/GRx
2703 CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
2704 be touched.
2705
2706 WARNING: Please make sure that this value is a multiple of
2707 the Linux page size (normally 4k). If this is not the case,
2708 then the end address of the Linux memory will be located at a
2709 non page size aligned address and this could cause major
2710 problems.
2711
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002712- CONFIG_SYS_TFTP_LOADADDR:
wdenkc6097192002-11-03 00:24:07 +00002713 Default load address for network file downloads
2714
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002715- CONFIG_SYS_LOADS_BAUD_CHANGE:
wdenkc6097192002-11-03 00:24:07 +00002716 Enable temporary baudrate change while serial download
2717
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002718- CONFIG_SYS_SDRAM_BASE:
wdenkc6097192002-11-03 00:24:07 +00002719 Physical start address of SDRAM. _Must_ be 0 here.
2720
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002721- CONFIG_SYS_MBIO_BASE:
wdenkc6097192002-11-03 00:24:07 +00002722 Physical start address of Motherboard I/O (if using a
2723 Cogent motherboard)
2724
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002725- CONFIG_SYS_FLASH_BASE:
wdenkc6097192002-11-03 00:24:07 +00002726 Physical start address of Flash memory.
2727
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002728- CONFIG_SYS_MONITOR_BASE:
wdenkc6097192002-11-03 00:24:07 +00002729 Physical start address of boot monitor code (set by
2730 make config files to be same as the text base address
Wolfgang Denk14d0a022010-10-07 21:51:12 +02002731 (CONFIG_SYS_TEXT_BASE) used when linking) - same as
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002732 CONFIG_SYS_FLASH_BASE when booting from flash.
wdenkc6097192002-11-03 00:24:07 +00002733
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002734- CONFIG_SYS_MONITOR_LEN:
wdenk8bde7f72003-06-27 21:31:46 +00002735 Size of memory reserved for monitor code, used to
2736 determine _at_compile_time_ (!) if the environment is
2737 embedded within the U-Boot image, or in a separate
2738 flash sector.
wdenkc6097192002-11-03 00:24:07 +00002739
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002740- CONFIG_SYS_MALLOC_LEN:
wdenkc6097192002-11-03 00:24:07 +00002741 Size of DRAM reserved for malloc() use.
2742
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002743- CONFIG_SYS_BOOTM_LEN:
Stefan Roese15940c92006-03-13 11:16:36 +01002744 Normally compressed uImages are limited to an
2745 uncompressed size of 8 MBytes. If this is not enough,
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002746 you can define CONFIG_SYS_BOOTM_LEN in your board config file
Stefan Roese15940c92006-03-13 11:16:36 +01002747 to adjust this setting to your needs.
2748
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002749- CONFIG_SYS_BOOTMAPSZ:
wdenkc6097192002-11-03 00:24:07 +00002750 Maximum size of memory mapped by the startup code of
2751 the Linux kernel; all data that must be processed by
Bartlomiej Sieka7d721e32008-04-14 15:44:16 +02002752 the Linux kernel (bd_info, boot arguments, FDT blob if
2753 used) must be put below this limit, unless "bootm_low"
2754 enviroment variable is defined and non-zero. In such case
2755 all data for the Linux kernel must be between "bootm_low"
Wolfgang Denkc0f40852011-10-26 10:21:21 +00002756 and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
Grant Likelyc3624e62011-03-28 09:58:43 +00002757 variable "bootm_mapsize" will override the value of
2758 CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
2759 then the value in "bootm_size" will be used instead.
wdenkc6097192002-11-03 00:24:07 +00002760
John Rigbyfca43cc2010-10-13 13:57:35 -06002761- CONFIG_SYS_BOOT_RAMDISK_HIGH:
2762 Enable initrd_high functionality. If defined then the
2763 initrd_high feature is enabled and the bootm ramdisk subcommand
2764 is enabled.
2765
2766- CONFIG_SYS_BOOT_GET_CMDLINE:
2767 Enables allocating and saving kernel cmdline in space between
2768 "bootm_low" and "bootm_low" + BOOTMAPSZ.
2769
2770- CONFIG_SYS_BOOT_GET_KBD:
2771 Enables allocating and saving a kernel copy of the bd_info in
2772 space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
2773
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002774- CONFIG_SYS_MAX_FLASH_BANKS:
wdenkc6097192002-11-03 00:24:07 +00002775 Max number of Flash memory banks
2776
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002777- CONFIG_SYS_MAX_FLASH_SECT:
wdenkc6097192002-11-03 00:24:07 +00002778 Max number of sectors on a Flash chip
2779
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002780- CONFIG_SYS_FLASH_ERASE_TOUT:
wdenkc6097192002-11-03 00:24:07 +00002781 Timeout for Flash erase operations (in ms)
2782
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002783- CONFIG_SYS_FLASH_WRITE_TOUT:
wdenkc6097192002-11-03 00:24:07 +00002784 Timeout for Flash write operations (in ms)
2785
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002786- CONFIG_SYS_FLASH_LOCK_TOUT
wdenk8564acf2003-07-14 22:13:32 +00002787 Timeout for Flash set sector lock bit operation (in ms)
2788
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002789- CONFIG_SYS_FLASH_UNLOCK_TOUT
wdenk8564acf2003-07-14 22:13:32 +00002790 Timeout for Flash clear lock bits operation (in ms)
2791
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002792- CONFIG_SYS_FLASH_PROTECTION
wdenk8564acf2003-07-14 22:13:32 +00002793 If defined, hardware flash sectors protection is used
2794 instead of U-Boot software protection.
2795
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002796- CONFIG_SYS_DIRECT_FLASH_TFTP:
wdenkc6097192002-11-03 00:24:07 +00002797
2798 Enable TFTP transfers directly to flash memory;
2799 without this option such a download has to be
2800 performed in two steps: (1) download to RAM, and (2)
2801 copy from RAM to flash.
2802
2803 The two-step approach is usually more reliable, since
2804 you can check if the download worked before you erase
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002805 the flash, but in some situations (when system RAM is
2806 too limited to allow for a temporary copy of the
wdenkc6097192002-11-03 00:24:07 +00002807 downloaded image) this option may be very useful.
2808
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002809- CONFIG_SYS_FLASH_CFI:
wdenk43d96162003-03-06 00:02:04 +00002810 Define if the flash driver uses extra elements in the
wdenk5653fc32004-02-08 22:55:38 +00002811 common flash structure for storing flash geometry.
2812
Jean-Christophe PLAGNIOL-VILLARD00b18832008-08-13 01:40:42 +02002813- CONFIG_FLASH_CFI_DRIVER
wdenk5653fc32004-02-08 22:55:38 +00002814 This option also enables the building of the cfi_flash driver
2815 in the drivers directory
wdenkc6097192002-11-03 00:24:07 +00002816
Piotr Ziecik91809ed2008-11-17 15:57:58 +01002817- CONFIG_FLASH_CFI_MTD
2818 This option enables the building of the cfi_mtd driver
2819 in the drivers directory. The driver exports CFI flash
2820 to the MTD layer.
2821
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002822- CONFIG_SYS_FLASH_USE_BUFFER_WRITE
Guennadi Liakhovetski96ef8312008-04-03 13:36:02 +02002823 Use buffered writes to flash.
2824
2825- CONFIG_FLASH_SPANSION_S29WS_N
2826 s29ws-n MirrorBit flash has non-standard addresses for buffered
2827 write commands.
2828
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002829- CONFIG_SYS_FLASH_QUIET_TEST
Stefan Roese5568e612005-11-22 13:20:42 +01002830 If this option is defined, the common CFI flash doesn't
2831 print it's warning upon not recognized FLASH banks. This
2832 is useful, if some of the configured banks are only
2833 optionally available.
2834
Jerry Van Baren9a042e92008-03-08 13:48:01 -05002835- CONFIG_FLASH_SHOW_PROGRESS
2836 If defined (must be an integer), print out countdown
2837 digits and dots. Recommended value: 45 (9..1) for 80
2838 column displays, 15 (3..1) for 40 column displays.
2839
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002840- CONFIG_SYS_RX_ETH_BUFFER:
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002841 Defines the number of Ethernet receive buffers. On some
2842 Ethernet controllers it is recommended to set this value
stroese53cf9432003-06-05 15:39:44 +00002843 to 8 or even higher (EEPRO100 or 405 EMAC), since all
2844 buffers can be full shortly after enabling the interface
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002845 on high Ethernet traffic.
stroese53cf9432003-06-05 15:39:44 +00002846 Defaults to 4 if not defined.
2847
Wolfgang Denkea882ba2010-06-20 23:33:59 +02002848- CONFIG_ENV_MAX_ENTRIES
2849
Wolfgang Denk071bc922010-10-27 22:48:30 +02002850 Maximum number of entries in the hash table that is used
2851 internally to store the environment settings. The default
2852 setting is supposed to be generous and should work in most
2853 cases. This setting can be used to tune behaviour; see
2854 lib/hashtable.c for details.
Wolfgang Denkea882ba2010-06-20 23:33:59 +02002855
wdenkc6097192002-11-03 00:24:07 +00002856The following definitions that deal with the placement and management
2857of environment data (variable area); in general, we support the
2858following configurations:
2859
Mike Frysingerc3eb3fe2011-07-08 10:44:25 +00002860- CONFIG_BUILD_ENVCRC:
2861
2862 Builds up envcrc with the target environment so that external utils
2863 may easily extract it and embed it in final U-Boot images.
2864
Jean-Christophe PLAGNIOL-VILLARD5a1aceb2008-09-10 22:48:04 +02002865- CONFIG_ENV_IS_IN_FLASH:
wdenkc6097192002-11-03 00:24:07 +00002866
2867 Define this if the environment is in flash memory.
2868
2869 a) The environment occupies one whole flash sector, which is
2870 "embedded" in the text segment with the U-Boot code. This
2871 happens usually with "bottom boot sector" or "top boot
2872 sector" type flash chips, which have several smaller
2873 sectors at the start or the end. For instance, such a
2874 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
2875 such a case you would place the environment in one of the
2876 4 kB sectors - with U-Boot code before and after it. With
2877 "top boot sector" type flash chips, you would put the
2878 environment in one of the last sectors, leaving a gap
2879 between U-Boot and the environment.
2880
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +02002881 - CONFIG_ENV_OFFSET:
wdenkc6097192002-11-03 00:24:07 +00002882
2883 Offset of environment data (variable area) to the
2884 beginning of flash memory; for instance, with bottom boot
2885 type flash chips the second sector can be used: the offset
2886 for this sector is given here.
2887
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002888 CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
wdenkc6097192002-11-03 00:24:07 +00002889
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +02002890 - CONFIG_ENV_ADDR:
wdenkc6097192002-11-03 00:24:07 +00002891
2892 This is just another way to specify the start address of
2893 the flash sector containing the environment (instead of
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +02002894 CONFIG_ENV_OFFSET).
wdenkc6097192002-11-03 00:24:07 +00002895
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +02002896 - CONFIG_ENV_SECT_SIZE:
wdenkc6097192002-11-03 00:24:07 +00002897
2898 Size of the sector containing the environment.
2899
2900
2901 b) Sometimes flash chips have few, equal sized, BIG sectors.
2902 In such a case you don't want to spend a whole sector for
2903 the environment.
2904
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +02002905 - CONFIG_ENV_SIZE:
wdenkc6097192002-11-03 00:24:07 +00002906
Jean-Christophe PLAGNIOL-VILLARD5a1aceb2008-09-10 22:48:04 +02002907 If you use this in combination with CONFIG_ENV_IS_IN_FLASH
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +02002908 and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
wdenkc6097192002-11-03 00:24:07 +00002909 of this flash sector for the environment. This saves
2910 memory for the RAM copy of the environment.
2911
2912 It may also save flash memory if you decide to use this
2913 when your environment is "embedded" within U-Boot code,
2914 since then the remainder of the flash sector could be used
2915 for U-Boot code. It should be pointed out that this is
2916 STRONGLY DISCOURAGED from a robustness point of view:
2917 updating the environment in flash makes it always
2918 necessary to erase the WHOLE sector. If something goes
2919 wrong before the contents has been restored from a copy in
2920 RAM, your target system will be dead.
2921
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +02002922 - CONFIG_ENV_ADDR_REDUND
2923 CONFIG_ENV_SIZE_REDUND
wdenkc6097192002-11-03 00:24:07 +00002924
wdenk43d96162003-03-06 00:02:04 +00002925 These settings describe a second storage area used to hold
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002926 a redundant copy of the environment data, so that there is
wdenk3e386912003-04-05 00:53:31 +00002927 a valid backup copy in case there is a power failure during
wdenk43d96162003-03-06 00:02:04 +00002928 a "saveenv" operation.
wdenkc6097192002-11-03 00:24:07 +00002929
2930BE CAREFUL! Any changes to the flash layout, and some changes to the
2931source code will make it necessary to adapt <board>/u-boot.lds*
2932accordingly!
2933
2934
Jean-Christophe PLAGNIOL-VILLARD9314cee2008-09-10 22:47:59 +02002935- CONFIG_ENV_IS_IN_NVRAM:
wdenkc6097192002-11-03 00:24:07 +00002936
2937 Define this if you have some non-volatile memory device
2938 (NVRAM, battery buffered SRAM) which you want to use for the
2939 environment.
2940
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +02002941 - CONFIG_ENV_ADDR:
2942 - CONFIG_ENV_SIZE:
wdenkc6097192002-11-03 00:24:07 +00002943
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002944 These two #defines are used to determine the memory area you
wdenkc6097192002-11-03 00:24:07 +00002945 want to use for environment. It is assumed that this memory
2946 can just be read and written to, without any special
2947 provision.
2948
2949BE CAREFUL! The first access to the environment happens quite early
2950in U-Boot initalization (when we try to get the setting of for the
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02002951console baudrate). You *MUST* have mapped your NVRAM area then, or
wdenkc6097192002-11-03 00:24:07 +00002952U-Boot will hang.
2953
2954Please note that even with NVRAM we still use a copy of the
2955environment in RAM: we could work on NVRAM directly, but we want to
2956keep settings there always unmodified except somebody uses "saveenv"
2957to save the current settings.
2958
2959
Jean-Christophe PLAGNIOL-VILLARDbb1f8b42008-09-05 09:19:30 +02002960- CONFIG_ENV_IS_IN_EEPROM:
wdenkc6097192002-11-03 00:24:07 +00002961
2962 Use this if you have an EEPROM or similar serial access
2963 device and a driver for it.
2964
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +02002965 - CONFIG_ENV_OFFSET:
2966 - CONFIG_ENV_SIZE:
wdenkc6097192002-11-03 00:24:07 +00002967
2968 These two #defines specify the offset and size of the
2969 environment area within the total memory of your EEPROM.
2970
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002971 - CONFIG_SYS_I2C_EEPROM_ADDR:
wdenkc6097192002-11-03 00:24:07 +00002972 If defined, specified the chip address of the EEPROM device.
2973 The default address is zero.
2974
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002975 - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
wdenkc6097192002-11-03 00:24:07 +00002976 If defined, the number of bits used to address bytes in a
2977 single page in the EEPROM device. A 64 byte page, for example
2978 would require six bits.
2979
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002980 - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
wdenkc6097192002-11-03 00:24:07 +00002981 If defined, the number of milliseconds to delay between
wdenkba56f622004-02-06 23:19:44 +00002982 page writes. The default is zero milliseconds.
wdenkc6097192002-11-03 00:24:07 +00002983
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002984 - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
wdenkc6097192002-11-03 00:24:07 +00002985 The length in bytes of the EEPROM memory array address. Note
2986 that this is NOT the chip address length!
2987
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002988 - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
wdenk5cf91d62004-04-23 20:32:05 +00002989 EEPROM chips that implement "address overflow" are ones
2990 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
2991 address and the extra bits end up in the "chip address" bit
2992 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
2993 byte chips.
2994
2995 Note that we consider the length of the address field to
2996 still be one byte because the extra address bits are hidden
2997 in the chip address.
2998
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02002999 - CONFIG_SYS_EEPROM_SIZE:
wdenkc6097192002-11-03 00:24:07 +00003000 The size in bytes of the EEPROM device.
3001
Heiko Schocher548738b2010-01-07 08:55:40 +01003002 - CONFIG_ENV_EEPROM_IS_ON_I2C
3003 define this, if you have I2C and SPI activated, and your
3004 EEPROM, which holds the environment, is on the I2C bus.
3005
3006 - CONFIG_I2C_ENV_EEPROM_BUS
3007 if you have an Environment on an EEPROM reached over
3008 I2C muxes, you can define here, how to reach this
3009 EEPROM. For example:
3010
Wolfgang Denka9046b92010-06-13 17:48:15 +02003011 #define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0"
Heiko Schocher548738b2010-01-07 08:55:40 +01003012
3013 EEPROM which holds the environment, is reached over
3014 a pca9547 i2c mux with address 0x70, channel 3.
wdenkc6097192002-11-03 00:24:07 +00003015
Jean-Christophe PLAGNIOL-VILLARD057c8492008-09-10 22:47:58 +02003016- CONFIG_ENV_IS_IN_DATAFLASH:
wdenk5779d8d2003-12-06 23:55:10 +00003017
wdenkd4ca31c2004-01-02 14:00:00 +00003018 Define this if you have a DataFlash memory device which you
wdenk5779d8d2003-12-06 23:55:10 +00003019 want to use for the environment.
3020
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +02003021 - CONFIG_ENV_OFFSET:
3022 - CONFIG_ENV_ADDR:
3023 - CONFIG_ENV_SIZE:
wdenk5779d8d2003-12-06 23:55:10 +00003024
3025 These three #defines specify the offset and size of the
3026 environment area within the total memory of your DataFlash placed
3027 at the specified address.
3028
Liu Gang0a85a9e2012-03-08 00:33:20 +00003029- CONFIG_ENV_IS_IN_REMOTE:
3030
3031 Define this if you have a remote memory space which you
3032 want to use for the local device's environment.
3033
3034 - CONFIG_ENV_ADDR:
3035 - CONFIG_ENV_SIZE:
3036
3037 These two #defines specify the address and size of the
3038 environment area within the remote memory space. The
3039 local device can get the environment from remote memory
3040 space by SRIO or other links.
3041
3042BE CAREFUL! For some special cases, the local device can not use
3043"saveenv" command. For example, the local device will get the
3044environment stored in a remote NOR flash by SRIO link, but it can
3045not erase, write this NOR flash by SRIO interface.
3046
Jean-Christophe PLAGNIOL-VILLARD51bfee12008-09-10 22:47:58 +02003047- CONFIG_ENV_IS_IN_NAND:
wdenk13a56952004-06-09 14:58:14 +00003048
3049 Define this if you have a NAND device which you want to use
3050 for the environment.
3051
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +02003052 - CONFIG_ENV_OFFSET:
3053 - CONFIG_ENV_SIZE:
wdenk13a56952004-06-09 14:58:14 +00003054
3055 These two #defines specify the offset and size of the environment
Scott Woodfdd813d2010-09-17 14:38:37 -05003056 area within the first NAND device. CONFIG_ENV_OFFSET must be
3057 aligned to an erase block boundary.
wdenk5779d8d2003-12-06 23:55:10 +00003058
Scott Woodfdd813d2010-09-17 14:38:37 -05003059 - CONFIG_ENV_OFFSET_REDUND (optional):
Markus Klotzbuechere443c942006-03-20 18:02:44 +01003060
Jean-Christophe PLAGNIOL-VILLARD0e8d1582008-09-10 22:48:06 +02003061 This setting describes a second storage area of CONFIG_ENV_SIZE
Scott Woodfdd813d2010-09-17 14:38:37 -05003062 size used to hold a redundant copy of the environment data, so
3063 that there is a valid backup copy in case there is a power failure
Wolfgang Denkc0f40852011-10-26 10:21:21 +00003064 during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
Scott Woodfdd813d2010-09-17 14:38:37 -05003065 aligned to an erase block boundary.
Markus Klotzbuechere443c942006-03-20 18:02:44 +01003066
Scott Woodfdd813d2010-09-17 14:38:37 -05003067 - CONFIG_ENV_RANGE (optional):
3068
3069 Specifies the length of the region in which the environment
3070 can be written. This should be a multiple of the NAND device's
3071 block size. Specifying a range with more erase blocks than
3072 are needed to hold CONFIG_ENV_SIZE allows bad blocks within
3073 the range to be avoided.
3074
3075 - CONFIG_ENV_OFFSET_OOB (optional):
3076
3077 Enables support for dynamically retrieving the offset of the
3078 environment from block zero's out-of-band data. The
3079 "nand env.oob" command can be used to record this offset.
3080 Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
3081 using CONFIG_ENV_OFFSET_OOB.
Markus Klotzbuechere443c942006-03-20 18:02:44 +01003082
Guennadi Liakhovetskib74ab732009-05-18 16:07:22 +02003083- CONFIG_NAND_ENV_DST
3084
3085 Defines address in RAM to which the nand_spl code should copy the
3086 environment. If redundant environment is used, it will be copied to
3087 CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
3088
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003089- CONFIG_SYS_SPI_INIT_OFFSET
wdenkc6097192002-11-03 00:24:07 +00003090
3091 Defines offset to the initial SPI buffer area in DPRAM. The
3092 area is used at an early stage (ROM part) if the environment
3093 is configured to reside in the SPI EEPROM: We need a 520 byte
3094 scratch DPRAM area. It is used between the two initialization
3095 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
3096 to be a good choice since it makes it far enough from the
3097 start of the data area as well as from the stack pointer.
3098
Bruce Adlere881cb52007-11-02 13:15:42 -07003099Please note that the environment is read-only until the monitor
wdenkc6097192002-11-03 00:24:07 +00003100has been relocated to RAM and a RAM copy of the environment has been
Wolfgang Denkcdb74972010-07-24 21:55:43 +02003101created; also, when using EEPROM you will have to use getenv_f()
wdenkc6097192002-11-03 00:24:07 +00003102until then to read environment variables.
3103
wdenk85ec0bc2003-03-31 16:34:49 +00003104The environment is protected by a CRC32 checksum. Before the monitor
3105is relocated into RAM, as a result of a bad CRC you will be working
3106with the compiled-in default environment - *silently*!!! [This is
3107necessary, because the first environment variable we need is the
3108"baudrate" setting for the console - if we have a bad CRC, we don't
3109have any device yet where we could complain.]
wdenkc6097192002-11-03 00:24:07 +00003110
3111Note: once the monitor has been relocated, then it will complain if
3112the default environment is used; a new CRC is computed as soon as you
wdenk85ec0bc2003-03-31 16:34:49 +00003113use the "saveenv" command to store a valid environment.
wdenkc6097192002-11-03 00:24:07 +00003114
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003115- CONFIG_SYS_FAULT_ECHO_LINK_DOWN:
wdenk42d1f032003-10-15 23:53:47 +00003116 Echo the inverted Ethernet link state to the fault LED.
wdenkfc3e2162003-10-08 22:33:00 +00003117
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003118 Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
wdenkfc3e2162003-10-08 22:33:00 +00003119 also needs to be defined.
3120
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003121- CONFIG_SYS_FAULT_MII_ADDR:
wdenk42d1f032003-10-15 23:53:47 +00003122 MII address of the PHY to check for the Ethernet link state.
wdenkc6097192002-11-03 00:24:07 +00003123
Ron Madridf5675aa2009-02-18 14:30:44 -08003124- CONFIG_NS16550_MIN_FUNCTIONS:
3125 Define this if you desire to only have use of the NS16550_init
3126 and NS16550_putc functions for the serial driver located at
3127 drivers/serial/ns16550.c. This option is useful for saving
3128 space for already greatly restricted images, including but not
3129 limited to NAND_SPL configurations.
3130
wdenkc6097192002-11-03 00:24:07 +00003131Low Level (hardware related) configuration options:
wdenkdc7c9a12003-03-26 06:55:25 +00003132---------------------------------------------------
wdenkc6097192002-11-03 00:24:07 +00003133
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003134- CONFIG_SYS_CACHELINE_SIZE:
wdenkc6097192002-11-03 00:24:07 +00003135 Cache Line Size of the CPU.
3136
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003137- CONFIG_SYS_DEFAULT_IMMR:
wdenkc6097192002-11-03 00:24:07 +00003138 Default address of the IMMR after system reset.
wdenk2535d602003-07-17 23:16:40 +00003139
wdenk42d1f032003-10-15 23:53:47 +00003140 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
3141 and RPXsuper) to be able to adjust the position of
3142 the IMMR register after a reset.
wdenkc6097192002-11-03 00:24:07 +00003143
Timur Tabie46fedf2011-08-04 18:03:41 -05003144- CONFIG_SYS_CCSRBAR_DEFAULT:
3145 Default (power-on reset) physical address of CCSR on Freescale
3146 PowerPC SOCs.
3147
3148- CONFIG_SYS_CCSRBAR:
3149 Virtual address of CCSR. On a 32-bit build, this is typically
3150 the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
3151
3152 CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
3153 for cross-platform code that uses that macro instead.
3154
3155- CONFIG_SYS_CCSRBAR_PHYS:
3156 Physical address of CCSR. CCSR can be relocated to a new
3157 physical address, if desired. In this case, this macro should
Wolfgang Denkc0f40852011-10-26 10:21:21 +00003158 be set to that address. Otherwise, it should be set to the
Timur Tabie46fedf2011-08-04 18:03:41 -05003159 same value as CONFIG_SYS_CCSRBAR_DEFAULT. For example, CCSR
3160 is typically relocated on 36-bit builds. It is recommended
3161 that this macro be defined via the _HIGH and _LOW macros:
3162
3163 #define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH
3164 * 1ull) << 32 | CONFIG_SYS_CCSRBAR_PHYS_LOW)
3165
3166- CONFIG_SYS_CCSRBAR_PHYS_HIGH:
Wolfgang Denk4cf26092011-10-07 09:58:21 +02003167 Bits 33-36 of CONFIG_SYS_CCSRBAR_PHYS. This value is typically
3168 either 0 (32-bit build) or 0xF (36-bit build). This macro is
Timur Tabie46fedf2011-08-04 18:03:41 -05003169 used in assembly code, so it must not contain typecasts or
3170 integer size suffixes (e.g. "ULL").
3171
3172- CONFIG_SYS_CCSRBAR_PHYS_LOW:
3173 Lower 32-bits of CONFIG_SYS_CCSRBAR_PHYS. This macro is
3174 used in assembly code, so it must not contain typecasts or
3175 integer size suffixes (e.g. "ULL").
3176
3177- CONFIG_SYS_CCSR_DO_NOT_RELOCATE:
3178 If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
3179 forced to a value that ensures that CCSR is not relocated.
3180
wdenk7f6c2cb2002-11-10 22:06:23 +00003181- Floppy Disk Support:
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003182 CONFIG_SYS_FDC_DRIVE_NUMBER
wdenk7f6c2cb2002-11-10 22:06:23 +00003183
3184 the default drive number (default value 0)
3185
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003186 CONFIG_SYS_ISA_IO_STRIDE
wdenk7f6c2cb2002-11-10 22:06:23 +00003187
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02003188 defines the spacing between FDC chipset registers
wdenk7f6c2cb2002-11-10 22:06:23 +00003189 (default value 1)
3190
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003191 CONFIG_SYS_ISA_IO_OFFSET
wdenk7f6c2cb2002-11-10 22:06:23 +00003192
wdenk43d96162003-03-06 00:02:04 +00003193 defines the offset of register from address. It
3194 depends on which part of the data bus is connected to
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02003195 the FDC chipset. (default value 0)
wdenk7f6c2cb2002-11-10 22:06:23 +00003196
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003197 If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
3198 CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
wdenk43d96162003-03-06 00:02:04 +00003199 default value.
wdenk7f6c2cb2002-11-10 22:06:23 +00003200
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003201 if CONFIG_SYS_FDC_HW_INIT is defined, then the function
wdenk43d96162003-03-06 00:02:04 +00003202 fdc_hw_init() is called at the beginning of the FDC
3203 setup. fdc_hw_init() must be provided by the board
3204 source code. It is used to make hardware dependant
3205 initializations.
wdenk7f6c2cb2002-11-10 22:06:23 +00003206
Macpaul Lin0abddf82011-04-11 20:45:32 +00003207- CONFIG_IDE_AHB:
3208 Most IDE controllers were designed to be connected with PCI
3209 interface. Only few of them were designed for AHB interface.
3210 When software is doing ATA command and data transfer to
3211 IDE devices through IDE-AHB controller, some additional
3212 registers accessing to these kind of IDE-AHB controller
3213 is requierd.
3214
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003215- CONFIG_SYS_IMMR: Physical address of the Internal Memory.
wdenkefe2a4d2004-12-16 21:44:03 +00003216 DO NOT CHANGE unless you know exactly what you're
wdenk25d67122004-12-10 11:40:40 +00003217 doing! (11-4) [MPC8xx/82xx systems only]
wdenkc6097192002-11-03 00:24:07 +00003218
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003219- CONFIG_SYS_INIT_RAM_ADDR:
wdenkc6097192002-11-03 00:24:07 +00003220
wdenk7152b1d2003-09-05 23:19:14 +00003221 Start address of memory area that can be used for
wdenkc6097192002-11-03 00:24:07 +00003222 initial data and stack; please note that this must be
3223 writable memory that is working WITHOUT special
3224 initialization, i. e. you CANNOT use normal RAM which
3225 will become available only after programming the
3226 memory controller and running certain initialization
3227 sequences.
3228
3229 U-Boot uses the following memory types:
3230 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
3231 - MPC824X: data cache
3232 - PPC4xx: data cache
3233
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003234- CONFIG_SYS_GBL_DATA_OFFSET:
wdenkc6097192002-11-03 00:24:07 +00003235
3236 Offset of the initial data structure in the memory
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003237 area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
3238 CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
wdenkc6097192002-11-03 00:24:07 +00003239 data is located at the end of the available space
Wolfgang Denk553f0982010-10-26 13:32:32 +02003240 (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003241 CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
3242 below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
3243 CONFIG_SYS_GBL_DATA_OFFSET) downward.
wdenkc6097192002-11-03 00:24:07 +00003244
3245 Note:
3246 On the MPC824X (or other systems that use the data
3247 cache for initial memory) the address chosen for
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003248 CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must
wdenkc6097192002-11-03 00:24:07 +00003249 point to an otherwise UNUSED address space between
3250 the top of RAM and the start of the PCI space.
3251
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003252- CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
wdenkc6097192002-11-03 00:24:07 +00003253
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003254- CONFIG_SYS_SYPCR: System Protection Control (11-9)
wdenkc6097192002-11-03 00:24:07 +00003255
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003256- CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
wdenkc6097192002-11-03 00:24:07 +00003257
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003258- CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
wdenkc6097192002-11-03 00:24:07 +00003259
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003260- CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
wdenkc6097192002-11-03 00:24:07 +00003261
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003262- CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
wdenkc6097192002-11-03 00:24:07 +00003263
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003264- CONFIG_SYS_OR_TIMING_SDRAM:
wdenkc6097192002-11-03 00:24:07 +00003265 SDRAM timing
3266
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003267- CONFIG_SYS_MAMR_PTA:
wdenkc6097192002-11-03 00:24:07 +00003268 periodic timer for refresh
3269
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003270- CONFIG_SYS_DER: Debug Event Register (37-47)
wdenkc6097192002-11-03 00:24:07 +00003271
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003272- FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
3273 CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
3274 CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
3275 CONFIG_SYS_BR1_PRELIM:
wdenkc6097192002-11-03 00:24:07 +00003276 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
3277
3278- SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003279 CONFIG_SYS_OR_TIMING_SDRAM, CONFIG_SYS_OR2_PRELIM, CONFIG_SYS_BR2_PRELIM,
3280 CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
wdenkc6097192002-11-03 00:24:07 +00003281 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
3282
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003283- CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K,
3284 CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL:
wdenkc6097192002-11-03 00:24:07 +00003285 Machine Mode Register and Memory Periodic Timer
3286 Prescaler definitions (SDRAM timing)
3287
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003288- CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
wdenkc6097192002-11-03 00:24:07 +00003289 enable I2C microcode relocation patch (MPC8xx);
3290 define relocation offset in DPRAM [DSP2]
3291
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003292- CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
Heiko Schocherb423d052008-01-11 01:12:07 +01003293 enable SMC microcode relocation patch (MPC8xx);
3294 define relocation offset in DPRAM [SMC1]
3295
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003296- CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
wdenkc6097192002-11-03 00:24:07 +00003297 enable SPI microcode relocation patch (MPC8xx);
3298 define relocation offset in DPRAM [SCC4]
3299
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003300- CONFIG_SYS_USE_OSCCLK:
wdenkc6097192002-11-03 00:24:07 +00003301 Use OSCM clock mode on MBX8xx board. Be careful,
3302 wrong setting might damage your board. Read
3303 doc/README.MBX before setting this variable!
3304
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003305- CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
wdenk43d96162003-03-06 00:02:04 +00003306 Offset of the bootmode word in DPRAM used by post
3307 (Power On Self Tests). This definition overrides
3308 #define'd default value in commproc.h resp.
3309 cpm_8260.h.
wdenkea909b72002-11-21 23:11:29 +00003310
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003311- CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB,
3312 CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL,
3313 CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS,
3314 CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB,
3315 CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
3316 CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
3317 CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
3318 CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
Stefan Roesea47a12b2010-04-15 16:07:28 +02003319 Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
wdenk5d232d02003-05-22 22:52:13 +00003320
Dirk Eibach9cacf4f2009-02-09 08:18:34 +01003321- CONFIG_PCI_DISABLE_PCIE:
3322 Disable PCI-Express on systems where it is supported but not
3323 required.
3324
Kumar Galaa09b9b62010-12-30 12:09:53 -06003325- CONFIG_SYS_SRIO:
3326 Chip has SRIO or not
3327
3328- CONFIG_SRIO1:
3329 Board has SRIO 1 port available
3330
3331- CONFIG_SRIO2:
3332 Board has SRIO 2 port available
3333
3334- CONFIG_SYS_SRIOn_MEM_VIRT:
3335 Virtual Address of SRIO port 'n' memory region
3336
3337- CONFIG_SYS_SRIOn_MEM_PHYS:
3338 Physical Address of SRIO port 'n' memory region
3339
3340- CONFIG_SYS_SRIOn_MEM_SIZE:
3341 Size of SRIO port 'n' memory region
3342
Alex Watermaneced4622011-05-19 15:08:36 -04003343- CONFIG_SYS_NDFC_16
3344 Defined to tell the NDFC that the NAND chip is using a
3345 16 bit bus.
3346
3347- CONFIG_SYS_NDFC_EBC0_CFG
3348 Sets the EBC0_CFG register for the NDFC. If not defined
3349 a default value will be used.
3350
Ben Warrenbb99ad62006-09-07 16:50:54 -04003351- CONFIG_SPD_EEPROM
Wolfgang Denk218ca722008-03-26 10:40:12 +01003352 Get DDR timing information from an I2C EEPROM. Common
3353 with pluggable memory modules such as SODIMMs
3354
Ben Warrenbb99ad62006-09-07 16:50:54 -04003355 SPD_EEPROM_ADDRESS
3356 I2C address of the SPD EEPROM
3357
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003358- CONFIG_SYS_SPD_BUS_NUM
Wolfgang Denk218ca722008-03-26 10:40:12 +01003359 If SPD EEPROM is on an I2C bus other than the first
3360 one, specify here. Note that the value must resolve
3361 to something your driver can deal with.
Ben Warrenbb99ad62006-09-07 16:50:54 -04003362
York Sun1b3e3c42011-06-07 09:42:16 +08003363- CONFIG_SYS_DDR_RAW_TIMING
3364 Get DDR timing information from other than SPD. Common with
3365 soldered DDR chips onboard without SPD. DDR raw timing
3366 parameters are extracted from datasheet and hard-coded into
3367 header files or board specific files.
3368
York Sun6f5e1dc2011-09-16 13:21:35 -07003369- CONFIG_FSL_DDR_INTERACTIVE
3370 Enable interactive DDR debugging. See doc/README.fsl-ddr.
3371
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003372- CONFIG_SYS_83XX_DDR_USES_CS0
Wolfgang Denk218ca722008-03-26 10:40:12 +01003373 Only for 83xx systems. If specified, then DDR should
3374 be configured using CS0 and CS1 instead of CS2 and CS3.
Timur Tabi2ad6b512006-10-31 18:44:42 -06003375
wdenkc26e4542004-04-18 10:13:26 +00003376- CONFIG_ETHER_ON_FEC[12]
3377 Define to enable FEC[12] on a 8xx series processor.
3378
3379- CONFIG_FEC[12]_PHY
3380 Define to the hardcoded PHY address which corresponds
wdenk6e592382004-04-18 17:39:38 +00003381 to the given FEC; i. e.
3382 #define CONFIG_FEC1_PHY 4
wdenkc26e4542004-04-18 10:13:26 +00003383 means that the PHY with address 4 is connected to FEC1
3384
3385 When set to -1, means to probe for first available.
3386
3387- CONFIG_FEC[12]_PHY_NORXERR
3388 The PHY does not have a RXERR line (RMII only).
3389 (so program the FEC to ignore it).
3390
3391- CONFIG_RMII
3392 Enable RMII mode for all FECs.
3393 Note that this is a global option, we can't
3394 have one FEC in standard MII mode and another in RMII mode.
3395
wdenk5cf91d62004-04-23 20:32:05 +00003396- CONFIG_CRC32_VERIFY
3397 Add a verify option to the crc32 command.
3398 The syntax is:
3399
3400 => crc32 -v <address> <count> <crc32>
3401
3402 Where address/count indicate a memory area
3403 and crc32 is the correct crc32 which the
3404 area should have.
3405
wdenk56523f12004-07-11 17:40:54 +00003406- CONFIG_LOOPW
3407 Add the "loopw" memory command. This only takes effect if
Jon Loeliger602ad3b2007-06-11 19:03:39 -05003408 the memory commands are activated globally (CONFIG_CMD_MEM).
wdenk56523f12004-07-11 17:40:54 +00003409
stroese7b466642004-12-16 18:46:55 +00003410- CONFIG_MX_CYCLIC
3411 Add the "mdc" and "mwc" memory commands. These are cyclic
3412 "md/mw" commands.
3413 Examples:
3414
wdenkefe2a4d2004-12-16 21:44:03 +00003415 => mdc.b 10 4 500
stroese7b466642004-12-16 18:46:55 +00003416 This command will print 4 bytes (10,11,12,13) each 500 ms.
3417
wdenkefe2a4d2004-12-16 21:44:03 +00003418 => mwc.l 100 12345678 10
stroese7b466642004-12-16 18:46:55 +00003419 This command will write 12345678 to address 100 all 10 ms.
3420
wdenkefe2a4d2004-12-16 21:44:03 +00003421 This only takes effect if the memory commands are activated
Jon Loeliger602ad3b2007-06-11 19:03:39 -05003422 globally (CONFIG_CMD_MEM).
stroese7b466642004-12-16 18:46:55 +00003423
wdenk8aa1a2d2005-04-04 12:44:11 +00003424- CONFIG_SKIP_LOWLEVEL_INIT
Macpaul Linafc1ce82011-10-19 20:41:11 +00003425 [ARM, NDS32, MIPS only] If this variable is defined, then certain
Wolfgang Denk844f07d2010-11-27 23:30:56 +01003426 low level initializations (like setting up the memory
3427 controller) are omitted and/or U-Boot does not
3428 relocate itself into RAM.
wdenk8aa1a2d2005-04-04 12:44:11 +00003429
Wolfgang Denk844f07d2010-11-27 23:30:56 +01003430 Normally this variable MUST NOT be defined. The only
3431 exception is when U-Boot is loaded (to RAM) by some
3432 other boot loader or by a debugger which performs
3433 these initializations itself.
wdenk8aa1a2d2005-04-04 12:44:11 +00003434
Aneesh V401bb302011-07-13 05:11:07 +00003435- CONFIG_SPL_BUILD
Magnus Liljadf812382009-06-13 20:50:00 +02003436 Modifies the behaviour of start.S when compiling a loader
3437 that is executed before the actual U-Boot. E.g. when
3438 compiling a NAND SPL.
wdenk400558b2005-04-02 23:52:25 +00003439
Matthias Weisserd8834a12011-03-10 21:36:32 +00003440- CONFIG_USE_ARCH_MEMCPY
3441 CONFIG_USE_ARCH_MEMSET
3442 If these options are used a optimized version of memcpy/memset will
3443 be used if available. These functions may be faster under some
3444 conditions but may increase the binary size.
3445
Timur Tabif2717b42011-11-22 09:21:25 -06003446Freescale QE/FMAN Firmware Support:
3447-----------------------------------
3448
3449The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the
3450loading of "firmware", which is encoded in the QE firmware binary format.
3451This firmware often needs to be loaded during U-Boot booting, so macros
3452are used to identify the storage device (NOR flash, SPI, etc) and the address
3453within that device.
3454
3455- CONFIG_SYS_QE_FMAN_FW_ADDR
3456 The address in the storage device where the firmware is located. The
3457 meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
3458 is also specified.
3459
3460- CONFIG_SYS_QE_FMAN_FW_LENGTH
3461 The maximum possible size of the firmware. The firmware binary format
3462 has a field that specifies the actual size of the firmware, but it
3463 might not be possible to read any part of the firmware unless some
3464 local storage is allocated to hold the entire firmware first.
3465
3466- CONFIG_SYS_QE_FMAN_FW_IN_NOR
3467 Specifies that QE/FMAN firmware is located in NOR flash, mapped as
3468 normal addressable memory via the LBC. CONFIG_SYS_FMAN_FW_ADDR is the
3469 virtual address in NOR flash.
3470
3471- CONFIG_SYS_QE_FMAN_FW_IN_NAND
3472 Specifies that QE/FMAN firmware is located in NAND flash.
3473 CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
3474
3475- CONFIG_SYS_QE_FMAN_FW_IN_MMC
3476 Specifies that QE/FMAN firmware is located on the primary SD/MMC
3477 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
3478
3479- CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH
3480 Specifies that QE/FMAN firmware is located on the primary SPI
3481 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
3482
Liu Gang292dc6c2012-03-08 00:33:18 +00003483- CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
3484 Specifies that QE/FMAN firmware is located in the remote (master)
3485 memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
3486 can be mapped from slave TLB->slave LAW->slave SRIO outbound window
3487 ->master inbound window->master LAW->the ucode address in master's
3488 NOR flash.
Timur Tabif2717b42011-11-22 09:21:25 -06003489
wdenkc6097192002-11-03 00:24:07 +00003490Building the Software:
3491======================
3492
Wolfgang Denk218ca722008-03-26 10:40:12 +01003493Building U-Boot has been tested in several native build environments
3494and in many different cross environments. Of course we cannot support
3495all possibly existing versions of cross development tools in all
3496(potentially obsolete) versions. In case of tool chain problems we
3497recommend to use the ELDK (see http://www.denx.de/wiki/DULG/ELDK)
3498which is extensively used to build and test U-Boot.
wdenkc6097192002-11-03 00:24:07 +00003499
Wolfgang Denk218ca722008-03-26 10:40:12 +01003500If you are not using a native environment, it is assumed that you
3501have GNU cross compiling tools available in your path. In this case,
3502you must set the environment variable CROSS_COMPILE in your shell.
3503Note that no changes to the Makefile or any other source files are
3504necessary. For example using the ELDK on a 4xx CPU, please enter:
wdenkc6097192002-11-03 00:24:07 +00003505
Wolfgang Denk218ca722008-03-26 10:40:12 +01003506 $ CROSS_COMPILE=ppc_4xx-
3507 $ export CROSS_COMPILE
wdenkc6097192002-11-03 00:24:07 +00003508
Peter Tyser2f8d3962009-03-13 18:54:51 -05003509Note: If you wish to generate Windows versions of the utilities in
3510 the tools directory you can use the MinGW toolchain
3511 (http://www.mingw.org). Set your HOST tools to the MinGW
3512 toolchain and execute 'make tools'. For example:
3513
3514 $ make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
3515
3516 Binaries such as tools/mkimage.exe will be created which can
3517 be executed on computers running Windows.
3518
Wolfgang Denk218ca722008-03-26 10:40:12 +01003519U-Boot is intended to be simple to build. After installing the
3520sources you must configure U-Boot for one specific board type. This
wdenkc6097192002-11-03 00:24:07 +00003521is done by typing:
3522
3523 make NAME_config
3524
Wolfgang Denk218ca722008-03-26 10:40:12 +01003525where "NAME_config" is the name of one of the existing configu-
Michael Jones4d675ae2012-03-15 22:48:10 +00003526rations; see boards.cfg for supported names.
wdenk54387ac2003-10-08 22:45:44 +00003527
wdenk2729af92004-05-03 20:45:30 +00003528Note: for some board special configuration names may exist; check if
3529 additional information is available from the board vendor; for
3530 instance, the TQM823L systems are available without (standard)
3531 or with LCD support. You can select such additional "features"
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02003532 when choosing the configuration, i. e.
wdenkc6097192002-11-03 00:24:07 +00003533
wdenk2729af92004-05-03 20:45:30 +00003534 make TQM823L_config
3535 - will configure for a plain TQM823L, i. e. no LCD support
wdenkc6097192002-11-03 00:24:07 +00003536
wdenk2729af92004-05-03 20:45:30 +00003537 make TQM823L_LCD_config
3538 - will configure for a TQM823L with U-Boot console on LCD
wdenkc6097192002-11-03 00:24:07 +00003539
wdenk2729af92004-05-03 20:45:30 +00003540 etc.
wdenkc6097192002-11-03 00:24:07 +00003541
wdenkc6097192002-11-03 00:24:07 +00003542
wdenk2729af92004-05-03 20:45:30 +00003543Finally, type "make all", and you should get some working U-Boot
3544images ready for download to / installation on your system:
wdenkc6097192002-11-03 00:24:07 +00003545
wdenk2729af92004-05-03 20:45:30 +00003546- "u-boot.bin" is a raw binary image
3547- "u-boot" is an image in ELF binary format
3548- "u-boot.srec" is in Motorola S-Record format
wdenkc6097192002-11-03 00:24:07 +00003549
Marian Balakowiczbaf31242006-09-07 17:25:40 +02003550By default the build is performed locally and the objects are saved
3551in the source directory. One of the two methods can be used to change
3552this behavior and build U-Boot to some external directory:
3553
35541. Add O= to the make command line invocations:
3555
3556 make O=/tmp/build distclean
3557 make O=/tmp/build NAME_config
3558 make O=/tmp/build all
3559
35602. Set environment variable BUILD_DIR to point to the desired location:
3561
3562 export BUILD_DIR=/tmp/build
3563 make distclean
3564 make NAME_config
3565 make all
3566
3567Note that the command line "O=" setting overrides the BUILD_DIR environment
3568variable.
3569
wdenkc6097192002-11-03 00:24:07 +00003570
wdenk2729af92004-05-03 20:45:30 +00003571Please be aware that the Makefiles assume you are using GNU make, so
3572for instance on NetBSD you might need to use "gmake" instead of
3573native "make".
wdenkc6097192002-11-03 00:24:07 +00003574
wdenkc6097192002-11-03 00:24:07 +00003575
wdenk2729af92004-05-03 20:45:30 +00003576If the system board that you have is not listed, then you will need
3577to port U-Boot to your hardware platform. To do this, follow these
3578steps:
wdenkc6097192002-11-03 00:24:07 +00003579
wdenk2729af92004-05-03 20:45:30 +000035801. Add a new configuration option for your board to the toplevel
Michael Jones4d675ae2012-03-15 22:48:10 +00003581 "boards.cfg" file, using the existing entries as examples.
3582 Follow the instructions there to keep the boards in order.
wdenk2729af92004-05-03 20:45:30 +000035832. Create a new directory to hold your board specific code. Add any
3584 files you need. In your board directory, you will need at least
3585 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
35863. Create a new configuration file "include/configs/<board>.h" for
3587 your board
35883. If you're porting U-Boot to a new CPU, then also create a new
3589 directory to hold your CPU specific code. Add any files you need.
35904. Run "make <board>_config" with your new name.
35915. Type "make", and you should get a working "u-boot.srec" file
3592 to be installed on your target system.
35936. Debug and solve any problems that might arise.
3594 [Of course, this last step is much harder than it sounds.]
wdenkc6097192002-11-03 00:24:07 +00003595
wdenkc6097192002-11-03 00:24:07 +00003596
wdenk2729af92004-05-03 20:45:30 +00003597Testing of U-Boot Modifications, Ports to New Hardware, etc.:
3598==============================================================
wdenkc6097192002-11-03 00:24:07 +00003599
Wolfgang Denk218ca722008-03-26 10:40:12 +01003600If you have modified U-Boot sources (for instance added a new board
3601or support for new devices, a new CPU, etc.) you are expected to
wdenk2729af92004-05-03 20:45:30 +00003602provide feedback to the other developers. The feedback normally takes
3603the form of a "patch", i. e. a context diff against a certain (latest
Wolfgang Denk218ca722008-03-26 10:40:12 +01003604official or latest in the git repository) version of U-Boot sources.
wdenkc6097192002-11-03 00:24:07 +00003605
Wolfgang Denk218ca722008-03-26 10:40:12 +01003606But before you submit such a patch, please verify that your modifi-
3607cation did not break existing code. At least make sure that *ALL* of
wdenk2729af92004-05-03 20:45:30 +00003608the supported boards compile WITHOUT ANY compiler warnings. To do so,
3609just run the "MAKEALL" script, which will configure and build U-Boot
Wolfgang Denk218ca722008-03-26 10:40:12 +01003610for ALL supported system. Be warned, this will take a while. You can
3611select which (cross) compiler to use by passing a `CROSS_COMPILE'
3612environment variable to the script, i. e. to use the ELDK cross tools
3613you can type
wdenkc6097192002-11-03 00:24:07 +00003614
wdenk2729af92004-05-03 20:45:30 +00003615 CROSS_COMPILE=ppc_8xx- MAKEALL
wdenkc6097192002-11-03 00:24:07 +00003616
wdenk2729af92004-05-03 20:45:30 +00003617or to build on a native PowerPC system you can type
wdenkc6097192002-11-03 00:24:07 +00003618
wdenk2729af92004-05-03 20:45:30 +00003619 CROSS_COMPILE=' ' MAKEALL
wdenkc6097192002-11-03 00:24:07 +00003620
Wolfgang Denk218ca722008-03-26 10:40:12 +01003621When using the MAKEALL script, the default behaviour is to build
3622U-Boot in the source directory. This location can be changed by
3623setting the BUILD_DIR environment variable. Also, for each target
3624built, the MAKEALL script saves two log files (<target>.ERR and
3625<target>.MAKEALL) in the <source dir>/LOG directory. This default
3626location can be changed by setting the MAKEALL_LOGDIR environment
3627variable. For example:
Marian Balakowiczbaf31242006-09-07 17:25:40 +02003628
3629 export BUILD_DIR=/tmp/build
3630 export MAKEALL_LOGDIR=/tmp/log
3631 CROSS_COMPILE=ppc_8xx- MAKEALL
3632
Wolfgang Denk218ca722008-03-26 10:40:12 +01003633With the above settings build objects are saved in the /tmp/build,
3634log files are saved in the /tmp/log and the source tree remains clean
3635during the whole build process.
Marian Balakowiczbaf31242006-09-07 17:25:40 +02003636
3637
wdenk2729af92004-05-03 20:45:30 +00003638See also "U-Boot Porting Guide" below.
wdenkc6097192002-11-03 00:24:07 +00003639
wdenkc6097192002-11-03 00:24:07 +00003640
wdenk2729af92004-05-03 20:45:30 +00003641Monitor Commands - Overview:
3642============================
wdenkc6097192002-11-03 00:24:07 +00003643
wdenk2729af92004-05-03 20:45:30 +00003644go - start application at address 'addr'
3645run - run commands in an environment variable
3646bootm - boot application image from memory
3647bootp - boot image via network using BootP/TFTP protocol
Marek Vasut44f074c2012-03-14 21:52:45 +00003648bootz - boot zImage from memory
wdenk2729af92004-05-03 20:45:30 +00003649tftpboot- boot image via network using TFTP protocol
3650 and env variables "ipaddr" and "serverip"
3651 (and eventually "gatewayip")
Simon Glass1fb7cd42011-10-24 18:00:07 +00003652tftpput - upload a file via network using TFTP protocol
wdenk2729af92004-05-03 20:45:30 +00003653rarpboot- boot image via network using RARP/TFTP protocol
3654diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
3655loads - load S-Record file over serial line
3656loadb - load binary file over serial line (kermit mode)
3657md - memory display
3658mm - memory modify (auto-incrementing)
3659nm - memory modify (constant address)
3660mw - memory write (fill)
3661cp - memory copy
3662cmp - memory compare
3663crc32 - checksum calculation
Peter Tyser0f89c542009-04-18 22:34:03 -05003664i2c - I2C sub-system
wdenk2729af92004-05-03 20:45:30 +00003665sspi - SPI utility commands
3666base - print or set address offset
3667printenv- print environment variables
3668setenv - set environment variables
3669saveenv - save environment variables to persistent storage
3670protect - enable or disable FLASH write protection
3671erase - erase FLASH memory
3672flinfo - print FLASH memory information
3673bdinfo - print Board Info structure
3674iminfo - print header information for application image
3675coninfo - print console devices and informations
3676ide - IDE sub-system
3677loop - infinite loop on address range
wdenk56523f12004-07-11 17:40:54 +00003678loopw - infinite write loop on address range
wdenk2729af92004-05-03 20:45:30 +00003679mtest - simple RAM test
3680icache - enable or disable instruction cache
3681dcache - enable or disable data cache
3682reset - Perform RESET of the CPU
3683echo - echo args to console
3684version - print monitor version
3685help - print online help
3686? - alias for 'help'
wdenkc6097192002-11-03 00:24:07 +00003687
wdenkc6097192002-11-03 00:24:07 +00003688
wdenk2729af92004-05-03 20:45:30 +00003689Monitor Commands - Detailed Description:
3690========================================
wdenkc6097192002-11-03 00:24:07 +00003691
wdenk2729af92004-05-03 20:45:30 +00003692TODO.
wdenkc6097192002-11-03 00:24:07 +00003693
wdenk2729af92004-05-03 20:45:30 +00003694For now: just type "help <command>".
wdenkc6097192002-11-03 00:24:07 +00003695
3696
wdenk2729af92004-05-03 20:45:30 +00003697Environment Variables:
3698======================
wdenkc6097192002-11-03 00:24:07 +00003699
wdenk2729af92004-05-03 20:45:30 +00003700U-Boot supports user configuration using Environment Variables which
3701can be made persistent by saving to Flash memory.
wdenkc6097192002-11-03 00:24:07 +00003702
wdenk2729af92004-05-03 20:45:30 +00003703Environment Variables are set using "setenv", printed using
3704"printenv", and saved to Flash using "saveenv". Using "setenv"
3705without a value can be used to delete a variable from the
3706environment. As long as you don't save the environment you are
3707working with an in-memory copy. In case the Flash area containing the
3708environment is erased by accident, a default environment is provided.
wdenkc6097192002-11-03 00:24:07 +00003709
Wolfgang Denkc96f86e2010-01-17 23:55:53 +01003710Some configuration options can be set using Environment Variables.
3711
3712List of environment variables (most likely not complete):
wdenkc6097192002-11-03 00:24:07 +00003713
wdenk2729af92004-05-03 20:45:30 +00003714 baudrate - see CONFIG_BAUDRATE
wdenkc6097192002-11-03 00:24:07 +00003715
wdenk2729af92004-05-03 20:45:30 +00003716 bootdelay - see CONFIG_BOOTDELAY
wdenkc6097192002-11-03 00:24:07 +00003717
wdenk2729af92004-05-03 20:45:30 +00003718 bootcmd - see CONFIG_BOOTCOMMAND
wdenkc6097192002-11-03 00:24:07 +00003719
wdenk2729af92004-05-03 20:45:30 +00003720 bootargs - Boot arguments when booting an RTOS image
wdenkc6097192002-11-03 00:24:07 +00003721
wdenk2729af92004-05-03 20:45:30 +00003722 bootfile - Name of the image to load with TFTP
wdenkc6097192002-11-03 00:24:07 +00003723
Bartlomiej Sieka7d721e32008-04-14 15:44:16 +02003724 bootm_low - Memory range available for image processing in the bootm
3725 command can be restricted. This variable is given as
3726 a hexadecimal number and defines lowest address allowed
3727 for use by the bootm command. See also "bootm_size"
3728 environment variable. Address defined by "bootm_low" is
3729 also the base of the initial memory mapping for the Linux
Grant Likelyc3624e62011-03-28 09:58:43 +00003730 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
3731 bootm_mapsize.
3732
Wolfgang Denkc0f40852011-10-26 10:21:21 +00003733 bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
Grant Likelyc3624e62011-03-28 09:58:43 +00003734 This variable is given as a hexadecimal number and it
3735 defines the size of the memory region starting at base
3736 address bootm_low that is accessible by the Linux kernel
3737 during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used
3738 as the default value if it is defined, and bootm_size is
3739 used otherwise.
Bartlomiej Sieka7d721e32008-04-14 15:44:16 +02003740
3741 bootm_size - Memory range available for image processing in the bootm
3742 command can be restricted. This variable is given as
3743 a hexadecimal number and defines the size of the region
3744 allowed for use by the bootm command. See also "bootm_low"
3745 environment variable.
3746
Bartlomiej Sieka4bae9092008-10-01 15:26:31 +02003747 updatefile - Location of the software update file on a TFTP server, used
3748 by the automatic software update feature. Please refer to
3749 documentation in doc/README.update for more details.
3750
wdenk2729af92004-05-03 20:45:30 +00003751 autoload - if set to "no" (any string beginning with 'n'),
3752 "bootp" will just load perform a lookup of the
3753 configuration from the BOOTP server, but not try to
3754 load any image using TFTP
wdenkc6097192002-11-03 00:24:07 +00003755
wdenk2729af92004-05-03 20:45:30 +00003756 autostart - if set to "yes", an image loaded using the "bootp",
3757 "rarpboot", "tftpboot" or "diskboot" commands will
3758 be automatically started (by internally calling
3759 "bootm")
wdenkc6097192002-11-03 00:24:07 +00003760
wdenk2729af92004-05-03 20:45:30 +00003761 If set to "no", a standalone image passed to the
3762 "bootm" command will be copied to the load address
3763 (and eventually uncompressed), but NOT be started.
3764 This can be used to load and uncompress arbitrary
3765 data.
wdenkc6097192002-11-03 00:24:07 +00003766
David A. Longa28afca2011-07-09 16:40:19 -04003767 fdt_high - if set this restricts the maximum address that the
3768 flattened device tree will be copied into upon boot.
Shawn Guofa34f6b2012-01-09 21:54:08 +00003769 For example, if you have a system with 1 GB memory
3770 at physical address 0x10000000, while Linux kernel
3771 only recognizes the first 704 MB as low memory, you
3772 may need to set fdt_high as 0x3C000000 to have the
3773 device tree blob be copied to the maximum address
3774 of the 704 MB low memory, so that Linux kernel can
3775 access it during the boot procedure.
3776
David A. Longa28afca2011-07-09 16:40:19 -04003777 If this is set to the special value 0xFFFFFFFF then
3778 the fdt will not be copied at all on boot. For this
3779 to work it must reside in writable memory, have
3780 sufficient padding on the end of it for u-boot to
3781 add the information it needs into it, and the memory
3782 must be accessible by the kernel.
3783
Simon Glasseea63e02011-10-24 19:15:34 +00003784 fdtcontroladdr- if set this is the address of the control flattened
3785 device tree used by U-Boot when CONFIG_OF_CONTROL is
3786 defined.
3787
wdenk17ea1172004-06-06 21:51:03 +00003788 i2cfast - (PPC405GP|PPC405EP only)
3789 if set to 'y' configures Linux I2C driver for fast
3790 mode (400kHZ). This environment variable is used in
3791 initialization code. So, for changes to be effective
3792 it must be saved and board must be reset.
3793
wdenk2729af92004-05-03 20:45:30 +00003794 initrd_high - restrict positioning of initrd images:
3795 If this variable is not set, initrd images will be
3796 copied to the highest possible address in RAM; this
3797 is usually what you want since it allows for
3798 maximum initrd size. If for some reason you want to
3799 make sure that the initrd image is loaded below the
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02003800 CONFIG_SYS_BOOTMAPSZ limit, you can set this environment
wdenk2729af92004-05-03 20:45:30 +00003801 variable to a value of "no" or "off" or "0".
3802 Alternatively, you can set it to a maximum upper
3803 address to use (U-Boot will still check that it
3804 does not overwrite the U-Boot stack and data).
wdenkc6097192002-11-03 00:24:07 +00003805
wdenk2729af92004-05-03 20:45:30 +00003806 For instance, when you have a system with 16 MB
3807 RAM, and want to reserve 4 MB from use by Linux,
3808 you can do this by adding "mem=12M" to the value of
3809 the "bootargs" variable. However, now you must make
3810 sure that the initrd image is placed in the first
3811 12 MB as well - this can be done with
wdenkc6097192002-11-03 00:24:07 +00003812
wdenk2729af92004-05-03 20:45:30 +00003813 setenv initrd_high 00c00000
wdenkc6097192002-11-03 00:24:07 +00003814
wdenk2729af92004-05-03 20:45:30 +00003815 If you set initrd_high to 0xFFFFFFFF, this is an
3816 indication to U-Boot that all addresses are legal
3817 for the Linux kernel, including addresses in flash
3818 memory. In this case U-Boot will NOT COPY the
3819 ramdisk at all. This may be useful to reduce the
3820 boot time on your system, but requires that this
3821 feature is supported by your Linux kernel.
wdenk4a6fd342003-04-12 23:38:12 +00003822
wdenk2729af92004-05-03 20:45:30 +00003823 ipaddr - IP address; needed for tftpboot command
wdenkc6097192002-11-03 00:24:07 +00003824
wdenk2729af92004-05-03 20:45:30 +00003825 loadaddr - Default load address for commands like "bootp",
3826 "rarpboot", "tftpboot", "loadb" or "diskboot"
wdenkc6097192002-11-03 00:24:07 +00003827
wdenk2729af92004-05-03 20:45:30 +00003828 loads_echo - see CONFIG_LOADS_ECHO
wdenkc6097192002-11-03 00:24:07 +00003829
wdenk2729af92004-05-03 20:45:30 +00003830 serverip - TFTP server IP address; needed for tftpboot command
wdenk38b99262003-05-23 23:18:21 +00003831
wdenk2729af92004-05-03 20:45:30 +00003832 bootretry - see CONFIG_BOOT_RETRY_TIME
wdenkc6097192002-11-03 00:24:07 +00003833
wdenk2729af92004-05-03 20:45:30 +00003834 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
wdenkc6097192002-11-03 00:24:07 +00003835
wdenk2729af92004-05-03 20:45:30 +00003836 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
wdenkc6097192002-11-03 00:24:07 +00003837
Mike Frysingere2a53452011-10-02 10:01:27 +00003838 ethprime - controls which interface is used first.
wdenkc6097192002-11-03 00:24:07 +00003839
Mike Frysingere2a53452011-10-02 10:01:27 +00003840 ethact - controls which interface is currently active.
3841 For example you can do the following
wdenkc6097192002-11-03 00:24:07 +00003842
Heiko Schocher48690d82010-07-20 17:45:02 +02003843 => setenv ethact FEC
3844 => ping 192.168.0.1 # traffic sent on FEC
3845 => setenv ethact SCC
3846 => ping 10.0.0.1 # traffic sent on SCC
wdenkc6097192002-11-03 00:24:07 +00003847
Matthias Fuchse1692572008-01-17 07:45:05 +01003848 ethrotate - When set to "no" U-Boot does not go through all
3849 available network interfaces.
3850 It just stays at the currently selected interface.
3851
Wolfgang Denkc96f86e2010-01-17 23:55:53 +01003852 netretry - When set to "no" each network operation will
wdenk2729af92004-05-03 20:45:30 +00003853 either succeed or fail without retrying.
3854 When set to "once" the network operation will
3855 fail when all the available network interfaces
3856 are tried once without success.
3857 Useful on scripts which control the retry operation
3858 themselves.
wdenkc6097192002-11-03 00:24:07 +00003859
Jean-Christophe PLAGNIOL-VILLARDb4e2f892009-01-31 09:53:39 +01003860 npe_ucode - set load address for the NPE microcode
Jean-Christophe PLAGNIOL-VILLARDa1cf0272008-01-07 08:41:34 +01003861
Wolfgang Denk28cb9372005-09-24 23:25:46 +02003862 tftpsrcport - If this is set, the value is used for TFTP's
Wolfgang Denkecb0ccd2005-09-24 22:37:32 +02003863 UDP source port.
3864
Wolfgang Denk28cb9372005-09-24 23:25:46 +02003865 tftpdstport - If this is set, the value is used for TFTP's UDP
3866 destination port instead of the Well Know Port 69.
3867
Wolfgang Denkc96f86e2010-01-17 23:55:53 +01003868 tftpblocksize - Block size to use for TFTP transfers; if not set,
3869 we use the TFTP server's default block size
3870
3871 tftptimeout - Retransmission timeout for TFTP packets (in milli-
3872 seconds, minimum value is 1000 = 1 second). Defines
3873 when a packet is considered to be lost so it has to
3874 be retransmitted. The default is 5000 = 5 seconds.
3875 Lowering this value may make downloads succeed
3876 faster in networks with high packet loss rates or
3877 with unreliable TFTP servers.
3878
3879 vlan - When set to a value < 4095 the traffic over
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02003880 Ethernet is encapsulated/received over 802.1q
wdenk2729af92004-05-03 20:45:30 +00003881 VLAN tagged frames.
wdenka3d991b2004-04-15 21:48:45 +00003882
Jason Hobbsdc0b7b02011-08-31 05:37:28 +00003883The following image location variables contain the location of images
3884used in booting. The "Image" column gives the role of the image and is
3885not an environment variable name. The other columns are environment
3886variable names. "File Name" gives the name of the file on a TFTP
3887server, "RAM Address" gives the location in RAM the image will be
3888loaded to, and "Flash Location" gives the image's address in NOR
3889flash or offset in NAND flash.
3890
3891*Note* - these variables don't have to be defined for all boards, some
3892boards currenlty use other variables for these purposes, and some
3893boards use these variables for other purposes.
3894
Wolfgang Denkc0f40852011-10-26 10:21:21 +00003895Image File Name RAM Address Flash Location
3896----- --------- ----------- --------------
3897u-boot u-boot u-boot_addr_r u-boot_addr
3898Linux kernel bootfile kernel_addr_r kernel_addr
3899device tree blob fdtfile fdt_addr_r fdt_addr
3900ramdisk ramdiskfile ramdisk_addr_r ramdisk_addr
Jason Hobbsdc0b7b02011-08-31 05:37:28 +00003901
wdenk2729af92004-05-03 20:45:30 +00003902The following environment variables may be used and automatically
3903updated by the network boot commands ("bootp" and "rarpboot"),
3904depending the information provided by your boot server:
wdenka3d991b2004-04-15 21:48:45 +00003905
wdenk2729af92004-05-03 20:45:30 +00003906 bootfile - see above
3907 dnsip - IP address of your Domain Name Server
3908 dnsip2 - IP address of your secondary Domain Name Server
3909 gatewayip - IP address of the Gateway (Router) to use
3910 hostname - Target hostname
3911 ipaddr - see above
3912 netmask - Subnet Mask
3913 rootpath - Pathname of the root filesystem on the NFS server
3914 serverip - see above
wdenka3d991b2004-04-15 21:48:45 +00003915
wdenka3d991b2004-04-15 21:48:45 +00003916
wdenk2729af92004-05-03 20:45:30 +00003917There are two special Environment Variables:
wdenkc6097192002-11-03 00:24:07 +00003918
wdenk2729af92004-05-03 20:45:30 +00003919 serial# - contains hardware identification information such
3920 as type string and/or serial number
3921 ethaddr - Ethernet address
wdenkc6097192002-11-03 00:24:07 +00003922
wdenk2729af92004-05-03 20:45:30 +00003923These variables can be set only once (usually during manufacturing of
3924the board). U-Boot refuses to delete or overwrite these variables
3925once they have been set once.
wdenkc6097192002-11-03 00:24:07 +00003926
3927
wdenk2729af92004-05-03 20:45:30 +00003928Further special Environment Variables:
wdenkc6097192002-11-03 00:24:07 +00003929
wdenk2729af92004-05-03 20:45:30 +00003930 ver - Contains the U-Boot version string as printed
3931 with the "version" command. This variable is
3932 readonly (see CONFIG_VERSION_VARIABLE).
wdenkc6097192002-11-03 00:24:07 +00003933
wdenkc6097192002-11-03 00:24:07 +00003934
wdenk2729af92004-05-03 20:45:30 +00003935Please note that changes to some configuration parameters may take
3936only effect after the next boot (yes, that's just like Windoze :-).
wdenkc6097192002-11-03 00:24:07 +00003937
stroesec1551ea2003-04-04 15:53:41 +00003938
wdenk2729af92004-05-03 20:45:30 +00003939Command Line Parsing:
3940=====================
stroesec1551ea2003-04-04 15:53:41 +00003941
wdenk2729af92004-05-03 20:45:30 +00003942There are two different command line parsers available with U-Boot:
3943the old "simple" one, and the much more powerful "hush" shell:
stroesec1551ea2003-04-04 15:53:41 +00003944
wdenk2729af92004-05-03 20:45:30 +00003945Old, simple command line parser:
3946--------------------------------
wdenkc6097192002-11-03 00:24:07 +00003947
wdenk2729af92004-05-03 20:45:30 +00003948- supports environment variables (through setenv / saveenv commands)
3949- several commands on one line, separated by ';'
Wolfgang Denkfe126d82005-11-20 21:40:11 +01003950- variable substitution using "... ${name} ..." syntax
wdenk2729af92004-05-03 20:45:30 +00003951- special characters ('$', ';') can be escaped by prefixing with '\',
3952 for example:
Wolfgang Denkfe126d82005-11-20 21:40:11 +01003953 setenv bootcmd bootm \${address}
wdenk2729af92004-05-03 20:45:30 +00003954- You can also escape text by enclosing in single apostrophes, for example:
3955 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
wdenkc6097192002-11-03 00:24:07 +00003956
wdenk2729af92004-05-03 20:45:30 +00003957Hush shell:
3958-----------
wdenkf07771c2003-05-28 08:06:31 +00003959
wdenk2729af92004-05-03 20:45:30 +00003960- similar to Bourne shell, with control structures like
3961 if...then...else...fi, for...do...done; while...do...done,
3962 until...do...done, ...
3963- supports environment ("global") variables (through setenv / saveenv
3964 commands) and local shell variables (through standard shell syntax
3965 "name=value"); only environment variables can be used with "run"
3966 command
wdenkf07771c2003-05-28 08:06:31 +00003967
wdenk2729af92004-05-03 20:45:30 +00003968General rules:
3969--------------
wdenkf07771c2003-05-28 08:06:31 +00003970
wdenk2729af92004-05-03 20:45:30 +00003971(1) If a command line (or an environment variable executed by a "run"
3972 command) contains several commands separated by semicolon, and
3973 one of these commands fails, then the remaining commands will be
3974 executed anyway.
wdenkf07771c2003-05-28 08:06:31 +00003975
wdenk2729af92004-05-03 20:45:30 +00003976(2) If you execute several variables with one call to run (i. e.
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02003977 calling run with a list of variables as arguments), any failing
wdenk2729af92004-05-03 20:45:30 +00003978 command will cause "run" to terminate, i. e. the remaining
3979 variables are not executed.
wdenkf07771c2003-05-28 08:06:31 +00003980
wdenk2729af92004-05-03 20:45:30 +00003981Note for Redundant Ethernet Interfaces:
3982=======================================
wdenkf07771c2003-05-28 08:06:31 +00003983
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02003984Some boards come with redundant Ethernet interfaces; U-Boot supports
wdenk2729af92004-05-03 20:45:30 +00003985such configurations and is capable of automatic selection of a
3986"working" interface when needed. MAC assignment works as follows:
wdenkf07771c2003-05-28 08:06:31 +00003987
wdenk2729af92004-05-03 20:45:30 +00003988Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
3989MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
3990"eth1addr" (=>eth1), "eth2addr", ...
wdenkf07771c2003-05-28 08:06:31 +00003991
wdenk2729af92004-05-03 20:45:30 +00003992If the network interface stores some valid MAC address (for instance
3993in SROM), this is used as default address if there is NO correspon-
3994ding setting in the environment; if the corresponding environment
3995variable is set, this overrides the settings in the card; that means:
wdenkf07771c2003-05-28 08:06:31 +00003996
wdenk2729af92004-05-03 20:45:30 +00003997o If the SROM has a valid MAC address, and there is no address in the
3998 environment, the SROM's address is used.
wdenkc6097192002-11-03 00:24:07 +00003999
wdenk2729af92004-05-03 20:45:30 +00004000o If there is no valid address in the SROM, and a definition in the
4001 environment exists, then the value from the environment variable is
4002 used.
wdenkc6097192002-11-03 00:24:07 +00004003
wdenk2729af92004-05-03 20:45:30 +00004004o If both the SROM and the environment contain a MAC address, and
4005 both addresses are the same, this MAC address is used.
wdenkc6097192002-11-03 00:24:07 +00004006
wdenk2729af92004-05-03 20:45:30 +00004007o If both the SROM and the environment contain a MAC address, and the
4008 addresses differ, the value from the environment is used and a
4009 warning is printed.
wdenkc6097192002-11-03 00:24:07 +00004010
wdenk2729af92004-05-03 20:45:30 +00004011o If neither SROM nor the environment contain a MAC address, an error
4012 is raised.
wdenkc6097192002-11-03 00:24:07 +00004013
Ben Warrenecee9322010-04-26 11:11:46 -07004014If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
Wolfgang Denkc0f40852011-10-26 10:21:21 +00004015will be programmed into hardware as part of the initialization process. This
Ben Warrenecee9322010-04-26 11:11:46 -07004016may be skipped by setting the appropriate 'ethmacskip' environment variable.
4017The naming convention is as follows:
4018"ethmacskip" (=>eth0), "eth1macskip" (=>eth1) etc.
wdenkc6097192002-11-03 00:24:07 +00004019
wdenk2729af92004-05-03 20:45:30 +00004020Image Formats:
4021==============
wdenkc6097192002-11-03 00:24:07 +00004022
Marian Balakowicz3310c542008-03-12 12:13:13 +01004023U-Boot is capable of booting (and performing other auxiliary operations on)
4024images in two formats:
4025
4026New uImage format (FIT)
4027-----------------------
4028
4029Flexible and powerful format based on Flattened Image Tree -- FIT (similar
4030to Flattened Device Tree). It allows the use of images with multiple
4031components (several kernels, ramdisks, etc.), with contents protected by
4032SHA1, MD5 or CRC32. More details are found in the doc/uImage.FIT directory.
4033
4034
4035Old uImage format
4036-----------------
4037
4038Old image format is based on binary files which can be basically anything,
4039preceded by a special header; see the definitions in include/image.h for
4040details; basically, the header defines the following image properties:
wdenkc6097192002-11-03 00:24:07 +00004041
wdenk2729af92004-05-03 20:45:30 +00004042* Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
4043 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
Peter Tyserf5ed9e32008-09-08 14:56:49 -05004044 LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
4045 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
4046 INTEGRITY).
Wolfgang Denk7b64fef2006-10-24 14:21:16 +02004047* Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
Macpaul Linafc1ce82011-10-19 20:41:11 +00004048 IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
4049 Currently supported: ARM, AVR32, Intel x86, MIPS, NDS32, Nios II, PowerPC).
wdenk2729af92004-05-03 20:45:30 +00004050* Compression Type (uncompressed, gzip, bzip2)
4051* Load Address
4052* Entry Point
4053* Image Name
4054* Image Timestamp
wdenkc6097192002-11-03 00:24:07 +00004055
wdenk2729af92004-05-03 20:45:30 +00004056The header is marked by a special Magic Number, and both the header
4057and the data portions of the image are secured against corruption by
4058CRC32 checksums.
wdenkc6097192002-11-03 00:24:07 +00004059
wdenkc6097192002-11-03 00:24:07 +00004060
wdenk2729af92004-05-03 20:45:30 +00004061Linux Support:
4062==============
wdenkc6097192002-11-03 00:24:07 +00004063
wdenk2729af92004-05-03 20:45:30 +00004064Although U-Boot should support any OS or standalone application
4065easily, the main focus has always been on Linux during the design of
4066U-Boot.
wdenkc6097192002-11-03 00:24:07 +00004067
wdenk2729af92004-05-03 20:45:30 +00004068U-Boot includes many features that so far have been part of some
4069special "boot loader" code within the Linux kernel. Also, any
4070"initrd" images to be used are no longer part of one big Linux image;
4071instead, kernel and "initrd" are separate images. This implementation
4072serves several purposes:
wdenkc6097192002-11-03 00:24:07 +00004073
wdenk2729af92004-05-03 20:45:30 +00004074- the same features can be used for other OS or standalone
4075 applications (for instance: using compressed images to reduce the
4076 Flash memory footprint)
wdenkc6097192002-11-03 00:24:07 +00004077
wdenk2729af92004-05-03 20:45:30 +00004078- it becomes much easier to port new Linux kernel versions because
4079 lots of low-level, hardware dependent stuff are done by U-Boot
wdenkc6097192002-11-03 00:24:07 +00004080
wdenk2729af92004-05-03 20:45:30 +00004081- the same Linux kernel image can now be used with different "initrd"
4082 images; of course this also means that different kernel images can
4083 be run with the same "initrd". This makes testing easier (you don't
4084 have to build a new "zImage.initrd" Linux image when you just
4085 change a file in your "initrd"). Also, a field-upgrade of the
4086 software is easier now.
wdenkc6097192002-11-03 00:24:07 +00004087
wdenkc6097192002-11-03 00:24:07 +00004088
wdenk2729af92004-05-03 20:45:30 +00004089Linux HOWTO:
4090============
wdenkc6097192002-11-03 00:24:07 +00004091
wdenk2729af92004-05-03 20:45:30 +00004092Porting Linux to U-Boot based systems:
4093---------------------------------------
wdenkc6097192002-11-03 00:24:07 +00004094
wdenk2729af92004-05-03 20:45:30 +00004095U-Boot cannot save you from doing all the necessary modifications to
4096configure the Linux device drivers for use with your target hardware
4097(no, we don't intend to provide a full virtual machine interface to
4098Linux :-).
wdenkc6097192002-11-03 00:24:07 +00004099
Stefan Roesea47a12b2010-04-15 16:07:28 +02004100But now you can ignore ALL boot loader code (in arch/powerpc/mbxboot).
wdenkc6097192002-11-03 00:24:07 +00004101
wdenk2729af92004-05-03 20:45:30 +00004102Just make sure your machine specific header file (for instance
4103include/asm-ppc/tqm8xx.h) includes the same definition of the Board
Markus Heidelberg1dc30692008-09-07 20:18:27 +02004104Information structure as we define in include/asm-<arch>/u-boot.h,
4105and make sure that your definition of IMAP_ADDR uses the same value
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02004106as your U-Boot configuration in CONFIG_SYS_IMMR.
wdenkc6097192002-11-03 00:24:07 +00004107
wdenkc6097192002-11-03 00:24:07 +00004108
wdenk2729af92004-05-03 20:45:30 +00004109Configuring the Linux kernel:
4110-----------------------------
wdenkc6097192002-11-03 00:24:07 +00004111
wdenk2729af92004-05-03 20:45:30 +00004112No specific requirements for U-Boot. Make sure you have some root
4113device (initial ramdisk, NFS) for your target system.
wdenkc6097192002-11-03 00:24:07 +00004114
wdenkc6097192002-11-03 00:24:07 +00004115
wdenk2729af92004-05-03 20:45:30 +00004116Building a Linux Image:
4117-----------------------
wdenkc6097192002-11-03 00:24:07 +00004118
wdenk2729af92004-05-03 20:45:30 +00004119With U-Boot, "normal" build targets like "zImage" or "bzImage" are
4120not used. If you use recent kernel source, a new build target
4121"uImage" will exist which automatically builds an image usable by
4122U-Boot. Most older kernels also have support for a "pImage" target,
4123which was introduced for our predecessor project PPCBoot and uses a
4124100% compatible format.
wdenkc6097192002-11-03 00:24:07 +00004125
wdenk2729af92004-05-03 20:45:30 +00004126Example:
wdenkc6097192002-11-03 00:24:07 +00004127
wdenk2729af92004-05-03 20:45:30 +00004128 make TQM850L_config
4129 make oldconfig
4130 make dep
4131 make uImage
wdenkc6097192002-11-03 00:24:07 +00004132
wdenk2729af92004-05-03 20:45:30 +00004133The "uImage" build target uses a special tool (in 'tools/mkimage') to
4134encapsulate a compressed Linux kernel image with header information,
4135CRC32 checksum etc. for use with U-Boot. This is what we are doing:
wdenkc6097192002-11-03 00:24:07 +00004136
wdenk2729af92004-05-03 20:45:30 +00004137* build a standard "vmlinux" kernel image (in ELF binary format):
wdenkc6097192002-11-03 00:24:07 +00004138
wdenk2729af92004-05-03 20:45:30 +00004139* convert the kernel into a raw binary image:
wdenkc6097192002-11-03 00:24:07 +00004140
wdenk2729af92004-05-03 20:45:30 +00004141 ${CROSS_COMPILE}-objcopy -O binary \
4142 -R .note -R .comment \
4143 -S vmlinux linux.bin
wdenkc6097192002-11-03 00:24:07 +00004144
wdenk2729af92004-05-03 20:45:30 +00004145* compress the binary image:
wdenkc6097192002-11-03 00:24:07 +00004146
wdenk2729af92004-05-03 20:45:30 +00004147 gzip -9 linux.bin
wdenkc6097192002-11-03 00:24:07 +00004148
wdenk2729af92004-05-03 20:45:30 +00004149* package compressed binary image for U-Boot:
wdenk24ee89b2002-11-03 17:56:27 +00004150
wdenk2729af92004-05-03 20:45:30 +00004151 mkimage -A ppc -O linux -T kernel -C gzip \
4152 -a 0 -e 0 -n "Linux Kernel Image" \
4153 -d linux.bin.gz uImage
wdenk24ee89b2002-11-03 17:56:27 +00004154
wdenk24ee89b2002-11-03 17:56:27 +00004155
wdenk2729af92004-05-03 20:45:30 +00004156The "mkimage" tool can also be used to create ramdisk images for use
4157with U-Boot, either separated from the Linux kernel image, or
4158combined into one file. "mkimage" encapsulates the images with a 64
4159byte header containing information about target architecture,
4160operating system, image type, compression method, entry points, time
4161stamp, CRC32 checksums, etc.
wdenk24ee89b2002-11-03 17:56:27 +00004162
wdenk2729af92004-05-03 20:45:30 +00004163"mkimage" can be called in two ways: to verify existing images and
4164print the header information, or to build new images.
wdenk24ee89b2002-11-03 17:56:27 +00004165
wdenk2729af92004-05-03 20:45:30 +00004166In the first form (with "-l" option) mkimage lists the information
4167contained in the header of an existing U-Boot image; this includes
4168checksum verification:
wdenk24ee89b2002-11-03 17:56:27 +00004169
wdenk2729af92004-05-03 20:45:30 +00004170 tools/mkimage -l image
4171 -l ==> list image header information
wdenk24ee89b2002-11-03 17:56:27 +00004172
wdenk2729af92004-05-03 20:45:30 +00004173The second form (with "-d" option) is used to build a U-Boot image
4174from a "data file" which is used as image payload:
wdenk24ee89b2002-11-03 17:56:27 +00004175
wdenk2729af92004-05-03 20:45:30 +00004176 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
4177 -n name -d data_file image
4178 -A ==> set architecture to 'arch'
4179 -O ==> set operating system to 'os'
4180 -T ==> set image type to 'type'
4181 -C ==> set compression type 'comp'
4182 -a ==> set load address to 'addr' (hex)
4183 -e ==> set entry point to 'ep' (hex)
4184 -n ==> set image name to 'name'
4185 -d ==> use image data from 'datafile'
wdenk24ee89b2002-11-03 17:56:27 +00004186
wdenk69459792004-05-29 16:53:29 +00004187Right now, all Linux kernels for PowerPC systems use the same load
4188address (0x00000000), but the entry point address depends on the
4189kernel version:
wdenkc6097192002-11-03 00:24:07 +00004190
wdenk2729af92004-05-03 20:45:30 +00004191- 2.2.x kernels have the entry point at 0x0000000C,
4192- 2.3.x and later kernels have the entry point at 0x00000000.
wdenkc6097192002-11-03 00:24:07 +00004193
wdenk2729af92004-05-03 20:45:30 +00004194So a typical call to build a U-Boot image would read:
wdenkc6097192002-11-03 00:24:07 +00004195
wdenk2729af92004-05-03 20:45:30 +00004196 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
4197 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
Stefan Roesea47a12b2010-04-15 16:07:28 +02004198 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz \
wdenk2729af92004-05-03 20:45:30 +00004199 > examples/uImage.TQM850L
4200 Image Name: 2.4.4 kernel for TQM850L
4201 Created: Wed Jul 19 02:34:59 2000
4202 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4203 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
4204 Load Address: 0x00000000
4205 Entry Point: 0x00000000
wdenkc6097192002-11-03 00:24:07 +00004206
wdenk2729af92004-05-03 20:45:30 +00004207To verify the contents of the image (or check for corruption):
wdenkc6097192002-11-03 00:24:07 +00004208
wdenk2729af92004-05-03 20:45:30 +00004209 -> tools/mkimage -l examples/uImage.TQM850L
4210 Image Name: 2.4.4 kernel for TQM850L
4211 Created: Wed Jul 19 02:34:59 2000
4212 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4213 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
4214 Load Address: 0x00000000
4215 Entry Point: 0x00000000
wdenkc6097192002-11-03 00:24:07 +00004216
wdenk2729af92004-05-03 20:45:30 +00004217NOTE: for embedded systems where boot time is critical you can trade
4218speed for memory and install an UNCOMPRESSED image instead: this
4219needs more space in Flash, but boots much faster since it does not
4220need to be uncompressed:
wdenkc6097192002-11-03 00:24:07 +00004221
Stefan Roesea47a12b2010-04-15 16:07:28 +02004222 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz
wdenk2729af92004-05-03 20:45:30 +00004223 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
4224 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
Stefan Roesea47a12b2010-04-15 16:07:28 +02004225 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux \
wdenk2729af92004-05-03 20:45:30 +00004226 > examples/uImage.TQM850L-uncompressed
4227 Image Name: 2.4.4 kernel for TQM850L
4228 Created: Wed Jul 19 02:34:59 2000
4229 Image Type: PowerPC Linux Kernel Image (uncompressed)
4230 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
4231 Load Address: 0x00000000
4232 Entry Point: 0x00000000
wdenkc6097192002-11-03 00:24:07 +00004233
wdenkc6097192002-11-03 00:24:07 +00004234
wdenk2729af92004-05-03 20:45:30 +00004235Similar you can build U-Boot images from a 'ramdisk.image.gz' file
4236when your kernel is intended to use an initial ramdisk:
wdenkdb01a2e2004-04-15 23:14:49 +00004237
wdenk2729af92004-05-03 20:45:30 +00004238 -> tools/mkimage -n 'Simple Ramdisk Image' \
4239 > -A ppc -O linux -T ramdisk -C gzip \
4240 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
4241 Image Name: Simple Ramdisk Image
4242 Created: Wed Jan 12 14:01:50 2000
4243 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
4244 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
4245 Load Address: 0x00000000
4246 Entry Point: 0x00000000
wdenkdb01a2e2004-04-15 23:14:49 +00004247
wdenkdb01a2e2004-04-15 23:14:49 +00004248
wdenk2729af92004-05-03 20:45:30 +00004249Installing a Linux Image:
4250-------------------------
wdenkdb01a2e2004-04-15 23:14:49 +00004251
wdenk2729af92004-05-03 20:45:30 +00004252To downloading a U-Boot image over the serial (console) interface,
4253you must convert the image to S-Record format:
wdenkdb01a2e2004-04-15 23:14:49 +00004254
wdenk2729af92004-05-03 20:45:30 +00004255 objcopy -I binary -O srec examples/image examples/image.srec
wdenkdb01a2e2004-04-15 23:14:49 +00004256
wdenk2729af92004-05-03 20:45:30 +00004257The 'objcopy' does not understand the information in the U-Boot
4258image header, so the resulting S-Record file will be relative to
4259address 0x00000000. To load it to a given address, you need to
4260specify the target address as 'offset' parameter with the 'loads'
4261command.
wdenkc6097192002-11-03 00:24:07 +00004262
wdenk2729af92004-05-03 20:45:30 +00004263Example: install the image to address 0x40100000 (which on the
4264TQM8xxL is in the first Flash bank):
wdenkc6097192002-11-03 00:24:07 +00004265
wdenk2729af92004-05-03 20:45:30 +00004266 => erase 40100000 401FFFFF
wdenkc6097192002-11-03 00:24:07 +00004267
wdenk2729af92004-05-03 20:45:30 +00004268 .......... done
4269 Erased 8 sectors
wdenkc6097192002-11-03 00:24:07 +00004270
wdenk2729af92004-05-03 20:45:30 +00004271 => loads 40100000
4272 ## Ready for S-Record download ...
4273 ~>examples/image.srec
4274 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
4275 ...
4276 15989 15990 15991 15992
4277 [file transfer complete]
4278 [connected]
4279 ## Start Addr = 0x00000000
wdenkc6097192002-11-03 00:24:07 +00004280
4281
wdenk2729af92004-05-03 20:45:30 +00004282You can check the success of the download using the 'iminfo' command;
Wolfgang Denk218ca722008-03-26 10:40:12 +01004283this includes a checksum verification so you can be sure no data
wdenk2729af92004-05-03 20:45:30 +00004284corruption happened:
wdenkc6097192002-11-03 00:24:07 +00004285
wdenk2729af92004-05-03 20:45:30 +00004286 => imi 40100000
wdenkc6097192002-11-03 00:24:07 +00004287
wdenk2729af92004-05-03 20:45:30 +00004288 ## Checking Image at 40100000 ...
4289 Image Name: 2.2.13 for initrd on TQM850L
4290 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4291 Data Size: 335725 Bytes = 327 kB = 0 MB
4292 Load Address: 00000000
4293 Entry Point: 0000000c
4294 Verifying Checksum ... OK
wdenkc6097192002-11-03 00:24:07 +00004295
4296
wdenk2729af92004-05-03 20:45:30 +00004297Boot Linux:
4298-----------
wdenkc6097192002-11-03 00:24:07 +00004299
wdenk2729af92004-05-03 20:45:30 +00004300The "bootm" command is used to boot an application that is stored in
4301memory (RAM or Flash). In case of a Linux kernel image, the contents
4302of the "bootargs" environment variable is passed to the kernel as
4303parameters. You can check and modify this variable using the
4304"printenv" and "setenv" commands:
wdenkc6097192002-11-03 00:24:07 +00004305
4306
wdenk2729af92004-05-03 20:45:30 +00004307 => printenv bootargs
4308 bootargs=root=/dev/ram
wdenkc6097192002-11-03 00:24:07 +00004309
wdenk2729af92004-05-03 20:45:30 +00004310 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
wdenkc6097192002-11-03 00:24:07 +00004311
wdenk2729af92004-05-03 20:45:30 +00004312 => printenv bootargs
4313 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
wdenkc6097192002-11-03 00:24:07 +00004314
wdenk2729af92004-05-03 20:45:30 +00004315 => bootm 40020000
4316 ## Booting Linux kernel at 40020000 ...
4317 Image Name: 2.2.13 for NFS on TQM850L
4318 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4319 Data Size: 381681 Bytes = 372 kB = 0 MB
4320 Load Address: 00000000
4321 Entry Point: 0000000c
4322 Verifying Checksum ... OK
4323 Uncompressing Kernel Image ... OK
4324 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
4325 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
4326 time_init: decrementer frequency = 187500000/60
4327 Calibrating delay loop... 49.77 BogoMIPS
4328 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
4329 ...
wdenkc6097192002-11-03 00:24:07 +00004330
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02004331If you want to boot a Linux kernel with initial RAM disk, you pass
wdenk2729af92004-05-03 20:45:30 +00004332the memory addresses of both the kernel and the initrd image (PPBCOOT
4333format!) to the "bootm" command:
wdenkc6097192002-11-03 00:24:07 +00004334
wdenk2729af92004-05-03 20:45:30 +00004335 => imi 40100000 40200000
wdenkc6097192002-11-03 00:24:07 +00004336
wdenk2729af92004-05-03 20:45:30 +00004337 ## Checking Image at 40100000 ...
4338 Image Name: 2.2.13 for initrd on TQM850L
4339 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4340 Data Size: 335725 Bytes = 327 kB = 0 MB
4341 Load Address: 00000000
4342 Entry Point: 0000000c
4343 Verifying Checksum ... OK
wdenkc6097192002-11-03 00:24:07 +00004344
wdenk2729af92004-05-03 20:45:30 +00004345 ## Checking Image at 40200000 ...
4346 Image Name: Simple Ramdisk Image
4347 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
4348 Data Size: 566530 Bytes = 553 kB = 0 MB
4349 Load Address: 00000000
4350 Entry Point: 00000000
4351 Verifying Checksum ... OK
wdenkc6097192002-11-03 00:24:07 +00004352
wdenk2729af92004-05-03 20:45:30 +00004353 => bootm 40100000 40200000
4354 ## Booting Linux kernel at 40100000 ...
4355 Image Name: 2.2.13 for initrd on TQM850L
4356 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4357 Data Size: 335725 Bytes = 327 kB = 0 MB
4358 Load Address: 00000000
4359 Entry Point: 0000000c
4360 Verifying Checksum ... OK
4361 Uncompressing Kernel Image ... OK
4362 ## Loading RAMDisk Image at 40200000 ...
4363 Image Name: Simple Ramdisk Image
4364 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
4365 Data Size: 566530 Bytes = 553 kB = 0 MB
4366 Load Address: 00000000
4367 Entry Point: 00000000
4368 Verifying Checksum ... OK
4369 Loading Ramdisk ... OK
4370 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
4371 Boot arguments: root=/dev/ram
4372 time_init: decrementer frequency = 187500000/60
4373 Calibrating delay loop... 49.77 BogoMIPS
4374 ...
4375 RAMDISK: Compressed image found at block 0
4376 VFS: Mounted root (ext2 filesystem).
wdenkc6097192002-11-03 00:24:07 +00004377
wdenk2729af92004-05-03 20:45:30 +00004378 bash#
wdenkc6097192002-11-03 00:24:07 +00004379
Matthew McClintock02677682006-06-28 10:41:37 -05004380Boot Linux and pass a flat device tree:
4381-----------
4382
4383First, U-Boot must be compiled with the appropriate defines. See the section
4384titled "Linux Kernel Interface" above for a more in depth explanation. The
4385following is an example of how to start a kernel and pass an updated
4386flat device tree:
4387
4388=> print oftaddr
4389oftaddr=0x300000
4390=> print oft
4391oft=oftrees/mpc8540ads.dtb
4392=> tftp $oftaddr $oft
4393Speed: 1000, full duplex
4394Using TSEC0 device
4395TFTP from server 192.168.1.1; our IP address is 192.168.1.101
4396Filename 'oftrees/mpc8540ads.dtb'.
4397Load address: 0x300000
4398Loading: #
4399done
4400Bytes transferred = 4106 (100a hex)
4401=> tftp $loadaddr $bootfile
4402Speed: 1000, full duplex
4403Using TSEC0 device
4404TFTP from server 192.168.1.1; our IP address is 192.168.1.2
4405Filename 'uImage'.
4406Load address: 0x200000
4407Loading:############
4408done
4409Bytes transferred = 1029407 (fb51f hex)
4410=> print loadaddr
4411loadaddr=200000
4412=> print oftaddr
4413oftaddr=0x300000
4414=> bootm $loadaddr - $oftaddr
4415## Booting image at 00200000 ...
Wolfgang Denka9398e02006-11-27 15:32:42 +01004416 Image Name: Linux-2.6.17-dirty
4417 Image Type: PowerPC Linux Kernel Image (gzip compressed)
4418 Data Size: 1029343 Bytes = 1005.2 kB
Matthew McClintock02677682006-06-28 10:41:37 -05004419 Load Address: 00000000
Wolfgang Denka9398e02006-11-27 15:32:42 +01004420 Entry Point: 00000000
Matthew McClintock02677682006-06-28 10:41:37 -05004421 Verifying Checksum ... OK
4422 Uncompressing Kernel Image ... OK
4423Booting using flat device tree at 0x300000
4424Using MPC85xx ADS machine description
4425Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
4426[snip]
4427
4428
wdenk2729af92004-05-03 20:45:30 +00004429More About U-Boot Image Types:
4430------------------------------
wdenk6069ff22003-02-28 00:49:47 +00004431
wdenk2729af92004-05-03 20:45:30 +00004432U-Boot supports the following image types:
wdenk6069ff22003-02-28 00:49:47 +00004433
wdenk2729af92004-05-03 20:45:30 +00004434 "Standalone Programs" are directly runnable in the environment
4435 provided by U-Boot; it is expected that (if they behave
4436 well) you can continue to work in U-Boot after return from
4437 the Standalone Program.
4438 "OS Kernel Images" are usually images of some Embedded OS which
4439 will take over control completely. Usually these programs
4440 will install their own set of exception handlers, device
4441 drivers, set up the MMU, etc. - this means, that you cannot
4442 expect to re-enter U-Boot except by resetting the CPU.
4443 "RAMDisk Images" are more or less just data blocks, and their
4444 parameters (address, size) are passed to an OS kernel that is
4445 being started.
4446 "Multi-File Images" contain several images, typically an OS
4447 (Linux) kernel image and one or more data images like
4448 RAMDisks. This construct is useful for instance when you want
4449 to boot over the network using BOOTP etc., where the boot
4450 server provides just a single image file, but you want to get
4451 for instance an OS kernel and a RAMDisk image.
stroesec1551ea2003-04-04 15:53:41 +00004452
wdenk2729af92004-05-03 20:45:30 +00004453 "Multi-File Images" start with a list of image sizes, each
4454 image size (in bytes) specified by an "uint32_t" in network
4455 byte order. This list is terminated by an "(uint32_t)0".
4456 Immediately after the terminating 0 follow the images, one by
4457 one, all aligned on "uint32_t" boundaries (size rounded up to
4458 a multiple of 4 bytes).
stroesec1551ea2003-04-04 15:53:41 +00004459
wdenk2729af92004-05-03 20:45:30 +00004460 "Firmware Images" are binary images containing firmware (like
4461 U-Boot or FPGA images) which usually will be programmed to
4462 flash memory.
stroesec1551ea2003-04-04 15:53:41 +00004463
wdenk2729af92004-05-03 20:45:30 +00004464 "Script files" are command sequences that will be executed by
4465 U-Boot's command interpreter; this feature is especially
4466 useful when you configure U-Boot to use a real shell (hush)
4467 as command interpreter.
wdenk6069ff22003-02-28 00:49:47 +00004468
Marek Vasut44f074c2012-03-14 21:52:45 +00004469Booting the Linux zImage:
4470-------------------------
4471
4472On some platforms, it's possible to boot Linux zImage. This is done
4473using the "bootz" command. The syntax of "bootz" command is the same
4474as the syntax of "bootm" command.
4475
Marek Vasut017e1f32012-03-18 11:47:58 +00004476Note, defining the CONFIG_SUPPORT_INITRD_RAW allows user to supply
4477kernel with raw initrd images. The syntax is slightly different, the
4478address of the initrd must be augmented by it's size, in the following
4479format: "<initrd addres>:<initrd size>".
4480
wdenkc6097192002-11-03 00:24:07 +00004481
wdenk2729af92004-05-03 20:45:30 +00004482Standalone HOWTO:
4483=================
wdenkc6097192002-11-03 00:24:07 +00004484
wdenk2729af92004-05-03 20:45:30 +00004485One of the features of U-Boot is that you can dynamically load and
4486run "standalone" applications, which can use some resources of
4487U-Boot like console I/O functions or interrupt services.
wdenkc6097192002-11-03 00:24:07 +00004488
wdenk2729af92004-05-03 20:45:30 +00004489Two simple examples are included with the sources:
wdenkc6097192002-11-03 00:24:07 +00004490
wdenk2729af92004-05-03 20:45:30 +00004491"Hello World" Demo:
4492-------------------
wdenkc6097192002-11-03 00:24:07 +00004493
wdenk2729af92004-05-03 20:45:30 +00004494'examples/hello_world.c' contains a small "Hello World" Demo
4495application; it is automatically compiled when you build U-Boot.
4496It's configured to run at address 0x00040004, so you can play with it
4497like that:
wdenkc6097192002-11-03 00:24:07 +00004498
wdenk2729af92004-05-03 20:45:30 +00004499 => loads
4500 ## Ready for S-Record download ...
4501 ~>examples/hello_world.srec
4502 1 2 3 4 5 6 7 8 9 10 11 ...
4503 [file transfer complete]
4504 [connected]
4505 ## Start Addr = 0x00040004
wdenkc6097192002-11-03 00:24:07 +00004506
wdenk2729af92004-05-03 20:45:30 +00004507 => go 40004 Hello World! This is a test.
4508 ## Starting application at 0x00040004 ...
4509 Hello World
4510 argc = 7
4511 argv[0] = "40004"
4512 argv[1] = "Hello"
4513 argv[2] = "World!"
4514 argv[3] = "This"
4515 argv[4] = "is"
4516 argv[5] = "a"
4517 argv[6] = "test."
4518 argv[7] = "<NULL>"
4519 Hit any key to exit ...
wdenkc6097192002-11-03 00:24:07 +00004520
wdenk2729af92004-05-03 20:45:30 +00004521 ## Application terminated, rc = 0x0
wdenkc6097192002-11-03 00:24:07 +00004522
wdenk2729af92004-05-03 20:45:30 +00004523Another example, which demonstrates how to register a CPM interrupt
4524handler with the U-Boot code, can be found in 'examples/timer.c'.
4525Here, a CPM timer is set up to generate an interrupt every second.
4526The interrupt service routine is trivial, just printing a '.'
4527character, but this is just a demo program. The application can be
4528controlled by the following keys:
wdenkc6097192002-11-03 00:24:07 +00004529
wdenk2729af92004-05-03 20:45:30 +00004530 ? - print current values og the CPM Timer registers
4531 b - enable interrupts and start timer
4532 e - stop timer and disable interrupts
4533 q - quit application
wdenkc6097192002-11-03 00:24:07 +00004534
wdenk2729af92004-05-03 20:45:30 +00004535 => loads
4536 ## Ready for S-Record download ...
4537 ~>examples/timer.srec
4538 1 2 3 4 5 6 7 8 9 10 11 ...
4539 [file transfer complete]
4540 [connected]
4541 ## Start Addr = 0x00040004
wdenkc6097192002-11-03 00:24:07 +00004542
wdenk2729af92004-05-03 20:45:30 +00004543 => go 40004
4544 ## Starting application at 0x00040004 ...
4545 TIMERS=0xfff00980
4546 Using timer 1
4547 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
wdenkc6097192002-11-03 00:24:07 +00004548
wdenk2729af92004-05-03 20:45:30 +00004549Hit 'b':
4550 [q, b, e, ?] Set interval 1000000 us
4551 Enabling timer
4552Hit '?':
4553 [q, b, e, ?] ........
4554 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
4555Hit '?':
4556 [q, b, e, ?] .
4557 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
4558Hit '?':
4559 [q, b, e, ?] .
4560 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
4561Hit '?':
4562 [q, b, e, ?] .
4563 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
4564Hit 'e':
4565 [q, b, e, ?] ...Stopping timer
4566Hit 'q':
4567 [q, b, e, ?] ## Application terminated, rc = 0x0
wdenkc6097192002-11-03 00:24:07 +00004568
4569
wdenk2729af92004-05-03 20:45:30 +00004570Minicom warning:
4571================
wdenk85ec0bc2003-03-31 16:34:49 +00004572
wdenk2729af92004-05-03 20:45:30 +00004573Over time, many people have reported problems when trying to use the
4574"minicom" terminal emulation program for serial download. I (wd)
4575consider minicom to be broken, and recommend not to use it. Under
4576Unix, I recommend to use C-Kermit for general purpose use (and
4577especially for kermit binary protocol download ("loadb" command), and
4578use "cu" for S-Record download ("loads" command).
wdenk85ec0bc2003-03-31 16:34:49 +00004579
wdenk2729af92004-05-03 20:45:30 +00004580Nevertheless, if you absolutely want to use it try adding this
4581configuration to your "File transfer protocols" section:
wdenk52f52c12003-06-19 23:04:19 +00004582
wdenk2729af92004-05-03 20:45:30 +00004583 Name Program Name U/D FullScr IO-Red. Multi
4584 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
4585 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
wdenk52f52c12003-06-19 23:04:19 +00004586
4587
wdenk2729af92004-05-03 20:45:30 +00004588NetBSD Notes:
4589=============
wdenkc6097192002-11-03 00:24:07 +00004590
wdenk2729af92004-05-03 20:45:30 +00004591Starting at version 0.9.2, U-Boot supports NetBSD both as host
4592(build U-Boot) and target system (boots NetBSD/mpc8xx).
wdenkc6097192002-11-03 00:24:07 +00004593
wdenk2729af92004-05-03 20:45:30 +00004594Building requires a cross environment; it is known to work on
4595NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
4596need gmake since the Makefiles are not compatible with BSD make).
4597Note that the cross-powerpc package does not install include files;
4598attempting to build U-Boot will fail because <machine/ansi.h> is
4599missing. This file has to be installed and patched manually:
wdenkc6097192002-11-03 00:24:07 +00004600
wdenk2729af92004-05-03 20:45:30 +00004601 # cd /usr/pkg/cross/powerpc-netbsd/include
4602 # mkdir powerpc
4603 # ln -s powerpc machine
4604 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
4605 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
wdenkc6097192002-11-03 00:24:07 +00004606
wdenk2729af92004-05-03 20:45:30 +00004607Native builds *don't* work due to incompatibilities between native
4608and U-Boot include files.
wdenkc6097192002-11-03 00:24:07 +00004609
wdenk2729af92004-05-03 20:45:30 +00004610Booting assumes that (the first part of) the image booted is a
4611stage-2 loader which in turn loads and then invokes the kernel
4612proper. Loader sources will eventually appear in the NetBSD source
4613tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
wdenk2a8af182005-04-13 10:02:42 +00004614meantime, see ftp://ftp.denx.de/pub/u-boot/ppcboot_stage2.tar.gz
wdenkc6097192002-11-03 00:24:07 +00004615
4616
wdenk2729af92004-05-03 20:45:30 +00004617Implementation Internals:
4618=========================
wdenkc6097192002-11-03 00:24:07 +00004619
wdenk2729af92004-05-03 20:45:30 +00004620The following is not intended to be a complete description of every
4621implementation detail. However, it should help to understand the
4622inner workings of U-Boot and make it easier to port it to custom
4623hardware.
wdenkc6097192002-11-03 00:24:07 +00004624
4625
wdenk2729af92004-05-03 20:45:30 +00004626Initial Stack, Global Data:
4627---------------------------
wdenkc6097192002-11-03 00:24:07 +00004628
wdenk2729af92004-05-03 20:45:30 +00004629The implementation of U-Boot is complicated by the fact that U-Boot
4630starts running out of ROM (flash memory), usually without access to
4631system RAM (because the memory controller is not initialized yet).
4632This means that we don't have writable Data or BSS segments, and BSS
4633is not initialized as zero. To be able to get a C environment working
4634at all, we have to allocate at least a minimal stack. Implementation
4635options for this are defined and restricted by the CPU used: Some CPU
4636models provide on-chip memory (like the IMMR area on MPC8xx and
4637MPC826x processors), on others (parts of) the data cache can be
4638locked as (mis-) used as memory, etc.
wdenkc6097192002-11-03 00:24:07 +00004639
Wolfgang Denk218ca722008-03-26 10:40:12 +01004640 Chris Hallinan posted a good summary of these issues to the
Wolfgang Denk06682362008-12-30 22:56:11 +01004641 U-Boot mailing list:
wdenk43d96162003-03-06 00:02:04 +00004642
wdenk2729af92004-05-03 20:45:30 +00004643 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
4644 From: "Chris Hallinan" <clh@net1plus.com>
4645 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
4646 ...
wdenk43d96162003-03-06 00:02:04 +00004647
wdenk2729af92004-05-03 20:45:30 +00004648 Correct me if I'm wrong, folks, but the way I understand it
4649 is this: Using DCACHE as initial RAM for Stack, etc, does not
4650 require any physical RAM backing up the cache. The cleverness
4651 is that the cache is being used as a temporary supply of
4652 necessary storage before the SDRAM controller is setup. It's
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02004653 beyond the scope of this list to explain the details, but you
wdenk2729af92004-05-03 20:45:30 +00004654 can see how this works by studying the cache architecture and
4655 operation in the architecture and processor-specific manuals.
wdenk43d96162003-03-06 00:02:04 +00004656
wdenk2729af92004-05-03 20:45:30 +00004657 OCM is On Chip Memory, which I believe the 405GP has 4K. It
4658 is another option for the system designer to use as an
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02004659 initial stack/RAM area prior to SDRAM being available. Either
wdenk2729af92004-05-03 20:45:30 +00004660 option should work for you. Using CS 4 should be fine if your
4661 board designers haven't used it for something that would
4662 cause you grief during the initial boot! It is frequently not
4663 used.
wdenk43d96162003-03-06 00:02:04 +00004664
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02004665 CONFIG_SYS_INIT_RAM_ADDR should be somewhere that won't interfere
wdenk2729af92004-05-03 20:45:30 +00004666 with your processor/board/system design. The default value
4667 you will find in any recent u-boot distribution in
Stefan Roese8a316c92005-08-01 16:49:12 +02004668 walnut.h should work for you. I'd set it to a value larger
wdenk2729af92004-05-03 20:45:30 +00004669 than your SDRAM module. If you have a 64MB SDRAM module, set
4670 it above 400_0000. Just make sure your board has no resources
4671 that are supposed to respond to that address! That code in
4672 start.S has been around a while and should work as is when
4673 you get the config right.
wdenk43d96162003-03-06 00:02:04 +00004674
wdenk2729af92004-05-03 20:45:30 +00004675 -Chris Hallinan
4676 DS4.COM, Inc.
wdenk43d96162003-03-06 00:02:04 +00004677
wdenk2729af92004-05-03 20:45:30 +00004678It is essential to remember this, since it has some impact on the C
4679code for the initialization procedures:
wdenkc6097192002-11-03 00:24:07 +00004680
wdenk2729af92004-05-03 20:45:30 +00004681* Initialized global data (data segment) is read-only. Do not attempt
4682 to write it.
wdenkc6097192002-11-03 00:24:07 +00004683
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02004684* Do not use any uninitialized global data (or implicitely initialized
wdenk2729af92004-05-03 20:45:30 +00004685 as zero data - BSS segment) at all - this is undefined, initiali-
4686 zation is performed later (when relocating to RAM).
wdenkc6097192002-11-03 00:24:07 +00004687
wdenk2729af92004-05-03 20:45:30 +00004688* Stack space is very limited. Avoid big data buffers or things like
4689 that.
wdenkc6097192002-11-03 00:24:07 +00004690
wdenk2729af92004-05-03 20:45:30 +00004691Having only the stack as writable memory limits means we cannot use
4692normal global data to share information beween the code. But it
4693turned out that the implementation of U-Boot can be greatly
4694simplified by making a global data structure (gd_t) available to all
4695functions. We could pass a pointer to this data as argument to _all_
4696functions, but this would bloat the code. Instead we use a feature of
4697the GCC compiler (Global Register Variables) to share the data: we
4698place a pointer (gd) to the global data into a register which we
4699reserve for this purpose.
wdenkc6097192002-11-03 00:24:07 +00004700
wdenk2729af92004-05-03 20:45:30 +00004701When choosing a register for such a purpose we are restricted by the
4702relevant (E)ABI specifications for the current architecture, and by
4703GCC's implementation.
wdenkc6097192002-11-03 00:24:07 +00004704
wdenk2729af92004-05-03 20:45:30 +00004705For PowerPC, the following registers have specific use:
4706 R1: stack pointer
Wolfgang Denke7670f62008-02-14 22:43:22 +01004707 R2: reserved for system use
wdenk2729af92004-05-03 20:45:30 +00004708 R3-R4: parameter passing and return values
4709 R5-R10: parameter passing
4710 R13: small data area pointer
4711 R30: GOT pointer
4712 R31: frame pointer
wdenkc6097192002-11-03 00:24:07 +00004713
Joakim Tjernlunde6bee802010-01-19 14:41:58 +01004714 (U-Boot also uses R12 as internal GOT pointer. r12
4715 is a volatile register so r12 needs to be reset when
4716 going back and forth between asm and C)
wdenkc6097192002-11-03 00:24:07 +00004717
Wolfgang Denke7670f62008-02-14 22:43:22 +01004718 ==> U-Boot will use R2 to hold a pointer to the global data
wdenkc6097192002-11-03 00:24:07 +00004719
wdenk2729af92004-05-03 20:45:30 +00004720 Note: on PPC, we could use a static initializer (since the
4721 address of the global data structure is known at compile time),
4722 but it turned out that reserving a register results in somewhat
4723 smaller code - although the code savings are not that big (on
4724 average for all boards 752 bytes for the whole U-Boot image,
4725 624 text + 127 data).
wdenkc6097192002-11-03 00:24:07 +00004726
Robin Getzc4db3352009-08-17 15:23:02 +00004727On Blackfin, the normal C ABI (except for P3) is followed as documented here:
Mike Frysinger4c58eb52008-02-04 19:26:54 -05004728 http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
4729
Robin Getzc4db3352009-08-17 15:23:02 +00004730 ==> U-Boot will use P3 to hold a pointer to the global data
Mike Frysinger4c58eb52008-02-04 19:26:54 -05004731
wdenk2729af92004-05-03 20:45:30 +00004732On ARM, the following registers are used:
wdenkc6097192002-11-03 00:24:07 +00004733
wdenk2729af92004-05-03 20:45:30 +00004734 R0: function argument word/integer result
4735 R1-R3: function argument word
4736 R9: GOT pointer
4737 R10: stack limit (used only if stack checking if enabled)
4738 R11: argument (frame) pointer
4739 R12: temporary workspace
4740 R13: stack pointer
4741 R14: link register
4742 R15: program counter
wdenkc6097192002-11-03 00:24:07 +00004743
wdenk2729af92004-05-03 20:45:30 +00004744 ==> U-Boot will use R8 to hold a pointer to the global data
wdenkc6097192002-11-03 00:24:07 +00004745
Thomas Chou0df01fd2010-05-21 11:08:03 +08004746On Nios II, the ABI is documented here:
4747 http://www.altera.com/literature/hb/nios2/n2cpu_nii51016.pdf
4748
4749 ==> U-Boot will use gp to hold a pointer to the global data
4750
4751 Note: on Nios II, we give "-G0" option to gcc and don't use gp
4752 to access small data sections, so gp is free.
4753
Macpaul Linafc1ce82011-10-19 20:41:11 +00004754On NDS32, the following registers are used:
4755
4756 R0-R1: argument/return
4757 R2-R5: argument
4758 R15: temporary register for assembler
4759 R16: trampoline register
4760 R28: frame pointer (FP)
4761 R29: global pointer (GP)
4762 R30: link register (LP)
4763 R31: stack pointer (SP)
4764 PC: program counter (PC)
4765
4766 ==> U-Boot will use R10 to hold a pointer to the global data
4767
Wolfgang Denkd87080b2006-03-31 18:32:53 +02004768NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
4769or current versions of GCC may "optimize" the code too much.
wdenkc6097192002-11-03 00:24:07 +00004770
wdenk2729af92004-05-03 20:45:30 +00004771Memory Management:
4772------------------
wdenkc6097192002-11-03 00:24:07 +00004773
wdenk2729af92004-05-03 20:45:30 +00004774U-Boot runs in system state and uses physical addresses, i.e. the
4775MMU is not used either for address mapping nor for memory protection.
wdenkc6097192002-11-03 00:24:07 +00004776
wdenk2729af92004-05-03 20:45:30 +00004777The available memory is mapped to fixed addresses using the memory
4778controller. In this process, a contiguous block is formed for each
4779memory type (Flash, SDRAM, SRAM), even when it consists of several
4780physical memory banks.
wdenkc6097192002-11-03 00:24:07 +00004781
wdenk2729af92004-05-03 20:45:30 +00004782U-Boot is installed in the first 128 kB of the first Flash bank (on
4783TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
4784booting and sizing and initializing DRAM, the code relocates itself
4785to the upper end of DRAM. Immediately below the U-Boot code some
Jean-Christophe PLAGNIOL-VILLARD6d0f6bc2008-10-16 15:01:15 +02004786memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN
wdenk2729af92004-05-03 20:45:30 +00004787configuration setting]. Below that, a structure with global Board
4788Info data is placed, followed by the stack (growing downward).
wdenkc6097192002-11-03 00:24:07 +00004789
wdenk2729af92004-05-03 20:45:30 +00004790Additionally, some exception handler code is copied to the low 8 kB
4791of DRAM (0x00000000 ... 0x00001FFF).
wdenkc6097192002-11-03 00:24:07 +00004792
wdenk2729af92004-05-03 20:45:30 +00004793So a typical memory configuration with 16 MB of DRAM could look like
4794this:
wdenkc6097192002-11-03 00:24:07 +00004795
wdenk2729af92004-05-03 20:45:30 +00004796 0x0000 0000 Exception Vector code
4797 :
4798 0x0000 1FFF
4799 0x0000 2000 Free for Application Use
4800 :
4801 :
wdenkc6097192002-11-03 00:24:07 +00004802
wdenk2729af92004-05-03 20:45:30 +00004803 :
4804 :
4805 0x00FB FF20 Monitor Stack (Growing downward)
4806 0x00FB FFAC Board Info Data and permanent copy of global data
4807 0x00FC 0000 Malloc Arena
4808 :
4809 0x00FD FFFF
4810 0x00FE 0000 RAM Copy of Monitor Code
4811 ... eventually: LCD or video framebuffer
4812 ... eventually: pRAM (Protected RAM - unchanged by reset)
4813 0x00FF FFFF [End of RAM]
wdenkc6097192002-11-03 00:24:07 +00004814
4815
wdenk2729af92004-05-03 20:45:30 +00004816System Initialization:
4817----------------------
wdenkc6097192002-11-03 00:24:07 +00004818
wdenk2729af92004-05-03 20:45:30 +00004819In the reset configuration, U-Boot starts at the reset entry point
Marcel Ziswiler11ccc332008-07-09 08:17:15 +02004820(on most PowerPC systems at address 0x00000100). Because of the reset
wdenk2729af92004-05-03 20:45:30 +00004821configuration for CS0# this is a mirror of the onboard Flash memory.
4822To be able to re-map memory U-Boot then jumps to its link address.
4823To be able to implement the initialization code in C, a (small!)
4824initial stack is set up in the internal Dual Ported RAM (in case CPUs
4825which provide such a feature like MPC8xx or MPC8260), or in a locked
4826part of the data cache. After that, U-Boot initializes the CPU core,
4827the caches and the SIU.
wdenkc6097192002-11-03 00:24:07 +00004828
wdenk2729af92004-05-03 20:45:30 +00004829Next, all (potentially) available memory banks are mapped using a
4830preliminary mapping. For example, we put them on 512 MB boundaries
4831(multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
4832on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
4833programmed for SDRAM access. Using the temporary configuration, a
4834simple memory test is run that determines the size of the SDRAM
4835banks.
wdenkc6097192002-11-03 00:24:07 +00004836
wdenk2729af92004-05-03 20:45:30 +00004837When there is more than one SDRAM bank, and the banks are of
4838different size, the largest is mapped first. For equal size, the first
4839bank (CS2#) is mapped first. The first mapping is always for address
48400x00000000, with any additional banks following immediately to create
4841contiguous memory starting from 0.
wdenkc6097192002-11-03 00:24:07 +00004842
wdenk2729af92004-05-03 20:45:30 +00004843Then, the monitor installs itself at the upper end of the SDRAM area
4844and allocates memory for use by malloc() and for the global Board
4845Info data; also, the exception vector code is copied to the low RAM
4846pages, and the final stack is set up.
wdenkc6097192002-11-03 00:24:07 +00004847
wdenk2729af92004-05-03 20:45:30 +00004848Only after this relocation will you have a "normal" C environment;
4849until that you are restricted in several ways, mostly because you are
4850running from ROM, and because the code will have to be relocated to a
4851new address in RAM.
wdenkc6097192002-11-03 00:24:07 +00004852
4853
wdenk2729af92004-05-03 20:45:30 +00004854U-Boot Porting Guide:
4855----------------------
wdenkc6097192002-11-03 00:24:07 +00004856
wdenk2729af92004-05-03 20:45:30 +00004857[Based on messages by Jerry Van Baren in the U-Boot-Users mailing
4858list, October 2002]
wdenkc6097192002-11-03 00:24:07 +00004859
4860
Jerry Van Baren6c3fef22009-07-15 20:42:59 -04004861int main(int argc, char *argv[])
wdenk2729af92004-05-03 20:45:30 +00004862{
4863 sighandler_t no_more_time;
wdenkc6097192002-11-03 00:24:07 +00004864
Jerry Van Baren6c3fef22009-07-15 20:42:59 -04004865 signal(SIGALRM, no_more_time);
4866 alarm(PROJECT_DEADLINE - toSec (3 * WEEK));
wdenkc6097192002-11-03 00:24:07 +00004867
wdenk2729af92004-05-03 20:45:30 +00004868 if (available_money > available_manpower) {
Jerry Van Baren6c3fef22009-07-15 20:42:59 -04004869 Pay consultant to port U-Boot;
wdenkc6097192002-11-03 00:24:07 +00004870 return 0;
4871 }
4872
wdenk2729af92004-05-03 20:45:30 +00004873 Download latest U-Boot source;
4874
Wolfgang Denk06682362008-12-30 22:56:11 +01004875 Subscribe to u-boot mailing list;
wdenk2729af92004-05-03 20:45:30 +00004876
Jerry Van Baren6c3fef22009-07-15 20:42:59 -04004877 if (clueless)
4878 email("Hi, I am new to U-Boot, how do I get started?");
wdenkc6097192002-11-03 00:24:07 +00004879
wdenk2729af92004-05-03 20:45:30 +00004880 while (learning) {
4881 Read the README file in the top level directory;
Jerry Van Baren6c3fef22009-07-15 20:42:59 -04004882 Read http://www.denx.de/twiki/bin/view/DULG/Manual;
4883 Read applicable doc/*.README;
wdenk2729af92004-05-03 20:45:30 +00004884 Read the source, Luke;
Jerry Van Baren6c3fef22009-07-15 20:42:59 -04004885 /* find . -name "*.[chS]" | xargs grep -i <keyword> */
wdenk2729af92004-05-03 20:45:30 +00004886 }
wdenkc6097192002-11-03 00:24:07 +00004887
Jerry Van Baren6c3fef22009-07-15 20:42:59 -04004888 if (available_money > toLocalCurrency ($2500))
4889 Buy a BDI3000;
4890 else
wdenk2729af92004-05-03 20:45:30 +00004891 Add a lot of aggravation and time;
Jerry Van Baren6c3fef22009-07-15 20:42:59 -04004892
4893 if (a similar board exists) { /* hopefully... */
4894 cp -a board/<similar> board/<myboard>
4895 cp include/configs/<similar>.h include/configs/<myboard>.h
4896 } else {
4897 Create your own board support subdirectory;
4898 Create your own board include/configs/<myboard>.h file;
wdenk2729af92004-05-03 20:45:30 +00004899 }
Jerry Van Baren6c3fef22009-07-15 20:42:59 -04004900 Edit new board/<myboard> files
4901 Edit new include/configs/<myboard>.h
wdenkc6097192002-11-03 00:24:07 +00004902
Jerry Van Baren6c3fef22009-07-15 20:42:59 -04004903 while (!accepted) {
4904 while (!running) {
4905 do {
4906 Add / modify source code;
4907 } until (compiles);
4908 Debug;
4909 if (clueless)
4910 email("Hi, I am having problems...");
4911 }
4912 Send patch file to the U-Boot email list;
4913 if (reasonable critiques)
4914 Incorporate improvements from email list code review;
4915 else
4916 Defend code as written;
wdenk2729af92004-05-03 20:45:30 +00004917 }
wdenkc6097192002-11-03 00:24:07 +00004918
wdenk2729af92004-05-03 20:45:30 +00004919 return 0;
4920}
4921
4922void no_more_time (int sig)
4923{
4924 hire_a_guru();
4925}
wdenkc6097192002-11-03 00:24:07 +00004926
4927
wdenk2729af92004-05-03 20:45:30 +00004928Coding Standards:
4929-----------------
wdenkc6097192002-11-03 00:24:07 +00004930
wdenk2729af92004-05-03 20:45:30 +00004931All contributions to U-Boot should conform to the Linux kernel
Detlev Zundel2c051652006-09-01 15:39:02 +02004932coding style; see the file "Documentation/CodingStyle" and the script
Wolfgang Denk7ca92962011-07-27 10:59:55 +00004933"scripts/Lindent" in your Linux kernel source directory.
wdenk2729af92004-05-03 20:45:30 +00004934
Detlev Zundel2c051652006-09-01 15:39:02 +02004935Source files originating from a different project (for example the
4936MTD subsystem) are generally exempt from these guidelines and are not
4937reformated to ease subsequent migration to newer versions of those
4938sources.
4939
4940Please note that U-Boot is implemented in C (and to some small parts in
4941Assembler); no C++ is used, so please do not use C++ style comments (//)
4942in your code.
wdenk2729af92004-05-03 20:45:30 +00004943
4944Please also stick to the following formatting rules:
4945- remove any trailing white space
Wolfgang Denk7ca92962011-07-27 10:59:55 +00004946- use TAB characters for indentation and vertical alignment, not spaces
wdenk2729af92004-05-03 20:45:30 +00004947- make sure NOT to use DOS '\r\n' line feeds
Wolfgang Denk7ca92962011-07-27 10:59:55 +00004948- do not add more than 2 consecutive empty lines to source files
wdenk2729af92004-05-03 20:45:30 +00004949- do not add trailing empty lines to source files
4950
4951Submissions which do not conform to the standards may be returned
4952with a request to reformat the changes.
wdenkc6097192002-11-03 00:24:07 +00004953
4954
wdenk2729af92004-05-03 20:45:30 +00004955Submitting Patches:
4956-------------------
wdenkc6097192002-11-03 00:24:07 +00004957
wdenk2729af92004-05-03 20:45:30 +00004958Since the number of patches for U-Boot is growing, we need to
4959establish some rules. Submissions which do not conform to these rules
4960may be rejected, even when they contain important and valuable stuff.
wdenkc6097192002-11-03 00:24:07 +00004961
Magnus Lilja0d28f342008-08-06 19:32:33 +02004962Please see http://www.denx.de/wiki/U-Boot/Patches for details.
Wolfgang Denk218ca722008-03-26 10:40:12 +01004963
Wolfgang Denk06682362008-12-30 22:56:11 +01004964Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;
4965see http://lists.denx.de/mailman/listinfo/u-boot
4966
wdenk2729af92004-05-03 20:45:30 +00004967When you send a patch, please include the following information with
4968it:
wdenkc6097192002-11-03 00:24:07 +00004969
wdenk2729af92004-05-03 20:45:30 +00004970* For bug fixes: a description of the bug and how your patch fixes
4971 this bug. Please try to include a way of demonstrating that the
4972 patch actually fixes something.
wdenkc6097192002-11-03 00:24:07 +00004973
wdenk2729af92004-05-03 20:45:30 +00004974* For new features: a description of the feature and your
4975 implementation.
wdenkc6097192002-11-03 00:24:07 +00004976
wdenk2729af92004-05-03 20:45:30 +00004977* A CHANGELOG entry as plaintext (separate from the patch)
4978
4979* For major contributions, your entry to the CREDITS file
4980
4981* When you add support for a new board, don't forget to add this
Wolfgang Denk7ca92962011-07-27 10:59:55 +00004982 board to the MAINTAINERS file, too.
wdenk2729af92004-05-03 20:45:30 +00004983
4984* If your patch adds new configuration options, don't forget to
4985 document these in the README file.
4986
Wolfgang Denk218ca722008-03-26 10:40:12 +01004987* The patch itself. If you are using git (which is *strongly*
4988 recommended) you can easily generate the patch using the
Wolfgang Denk7ca92962011-07-27 10:59:55 +00004989 "git format-patch". If you then use "git send-email" to send it to
Wolfgang Denk218ca722008-03-26 10:40:12 +01004990 the U-Boot mailing list, you will avoid most of the common problems
4991 with some other mail clients.
wdenk2729af92004-05-03 20:45:30 +00004992
Wolfgang Denk218ca722008-03-26 10:40:12 +01004993 If you cannot use git, use "diff -purN OLD NEW". If your version of
4994 diff does not support these options, then get the latest version of
4995 GNU diff.
wdenk2729af92004-05-03 20:45:30 +00004996
Wolfgang Denk218ca722008-03-26 10:40:12 +01004997 The current directory when running this command shall be the parent
4998 directory of the U-Boot source tree (i. e. please make sure that
4999 your patch includes sufficient directory information for the
5000 affected files).
5001
5002 We prefer patches as plain text. MIME attachments are discouraged,
5003 and compressed attachments must not be used.
wdenk2729af92004-05-03 20:45:30 +00005004
5005* If one logical set of modifications affects or creates several
5006 files, all these changes shall be submitted in a SINGLE patch file.
5007
5008* Changesets that contain different, unrelated modifications shall be
5009 submitted as SEPARATE patches, one patch per changeset.
5010
5011
5012Notes:
5013
5014* Before sending the patch, run the MAKEALL script on your patched
5015 source tree and make sure that no errors or warnings are reported
5016 for any of the boards.
5017
5018* Keep your modifications to the necessary minimum: A patch
5019 containing several unrelated changes or arbitrary reformats will be
5020 returned with a request to re-formatting / split it.
5021
5022* If you modify existing code, make sure that your new code does not
5023 add to the memory footprint of the code ;-) Small is beautiful!
5024 When adding new features, these should compile conditionally only
5025 (using #ifdef), and the resulting code with the new feature
5026 disabled must not need more memory than the old code without your
5027 modification.
wdenk90dc6702005-05-03 14:12:25 +00005028
Wolfgang Denk06682362008-12-30 22:56:11 +01005029* Remember that there is a size limit of 100 kB per message on the
5030 u-boot mailing list. Bigger patches will be moderated. If they are
5031 reasonable and not too big, they will be acknowledged. But patches
5032 bigger than the size limit should be avoided.